After adding display power domain for Exynos5250 in commit
2d2c9a8d0a ("ARM: dts: add display power domain for exynos5250") the
display on Chromebook Snow and others stopped working after boot.
The reason for this suggested Andrzej Hajda: the DP clock was disabled.
This clock is required by Display Port and is enabled by bootloader.
However when FIMD driver probing was deferred, the display power domain
was turned off. This effectively reset the value of DP clock enable
register.
When exynos-dp is later probed, the clock is not enabled and display is
not properly configured:
exynos-dp 145b0000.dp-controller: Timeout of video streamclk ok
exynos-dp 145b0000.dp-controller: unable to config video
Fixes: 2d2c9a8d0a ("ARM: dts: add display power domain for exynos5250")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reported-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
XR24 planes were not shown properly, so now set the right registers
to correctly enable displaying these planes.
It also moves the alpha register settings to fimd_win_set_pixfmt()
to keep all pixel format stuff together.
v2: remove leftover var alpha
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch consolidates the different interface_pix_fmt, pixel_fmt, pix_fmt,
and pixfmt variables to a common name "bus_format" wherever they describe the
pixel format on the bus between display controller and encoder hardware.
At the same time, it renames imx_drm_panel_format to imx_drm_set_bus_format.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Tested-by: Emil Renner Berthing <kernel@esmil.dk>
At the moment the enum values for ACTIVE_HIGH and RISING_EDGE are 0, and
ACTIVE_LOW and FALLING_EDGE are 1, to match the values programmed to HW.
The previous patch removed this dependency.
Swap the enum values the other way around. This doesn't change the
behavior in any way, but makes it easier to debug as value of '1' means
HIGH or RISING.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DISPC can drive data lines either on rising or falling pixel clock edge,
which can be configured by the user.
Sync lines can also be driven on rising or falling pixel clock edge, but
additionally the HW can be configured to drive the sync lines on
opposite clock edge from the data lines.
This opposite edge setting does not make any sense, as the same effect
can be achieved by just setting the sync lines to be driven on the other
edge compared to the data lines. It feels like some kind of backward
compatibility option, even if all DSS versions seem to have the same
implementation.
To simplify the code and configuration of the signals, and to make the
dispc timings more compatible with what is used on other platforms,
let's just remove the whole opposite-edge support.
The drivers that used OMAPDSS_DRIVE_SIG_OPPOSITE_EDGES setting are
changed so that they use the opposite setting from the data edge.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omapdss's sysfs directories for displays used to have 'name' file,
giving the name for the display. This file was later renamed to
'display_name' to avoid conflicts with i2c sysfs 'name' file. Looks like
at least xserver-xorg-video-omap3 requires the 'name' file to be
present.
To fix the regression, this patch creates new kobjects for each display,
allowing us to create sysfs directories for the displays. This way we
have the whole directory for omapdss, and there will be no sysfs file
clashes with the underlying display device's sysfs files.
We can thus add the 'name' sysfs file back.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: NeilBrown <neilb@suse.de>
Pull drm updates from Dave Airlie:
"This is the main drm pull, it has a shared branch with some alsa
crossover but everything should be acked by relevant people.
New drivers:
- ATMEL HLCDC driver
- designware HDMI core support (used in multiple SoCs).
core:
- lots more atomic modesetting work, properties and atomic ioctl
(hidden under option)
- bridge rework allows support for Samsung exynos chromebooks to
work finally.
- some more panels supported
i915:
- atomic plane update support
- DSI uses shared DSI infrastructure
- Skylake basic support is all merged now
- component framework used for i915/snd-hda interactions
- write-combine cpu memory mappings
- engine init code refactored
- full ppgtt enabled where execlists are enabled.
- cherryview rps/gpu turbo and pipe CRC support.
radeon:
- indirect draw support for evergreen/cayman
- SMC and manual fan control for SI/CI
- Displayport audio support
amdkfd:
- SDMA usermode queue support
- replace suballocator usage with more suitable one
- rework for allowing interfacing to more than radeon
nouveau:
- major renaming in prep for later splitting work
- merge arm platform driver into nouveau
- GK20A reclocking support
msm:
- conversion to atomic modesetting
- YUV support for mdp4/5
- eDP support
- hw cursor for mdp5
tegra:
- conversion to atomic modesetting
- better suspend/resume support for child devices
rcar-du:
- interlaced support
imx:
- move to using dw_hdmi shared support
- mode_fixup support
sti:
- DVO support
- HDMI infoframe support
exynos:
- refactoring and cleanup, removed lots of internal unnecessary
abstraction
- exynos7 DECON display controller support
Along with the usual bunch of fixes, cleanups etc"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (724 commits)
drm/radeon: fix voltage setup on hawaii
drm/radeon/dp: Set EDP_CONFIGURATION_SET for bridge chips if necessary
drm/radeon: only enable kv/kb dpm interrupts once v3
drm/radeon: workaround for CP HW bug on CIK
drm/radeon: Don't try to enable write-combining without PAT
drm/radeon: use 0-255 rather than 0-100 for pwm fan range
drm/i915: Clamp efficient frequency to valid range
drm/i915: Really ignore long HPD pulses on eDP
drm/exynos: Add DECON driver
drm/i915: Correct the base value while updating LP_OUTPUT_HOLD in MIPI_PORT_CTRL
drm/i915: Insert a command barrier on BLT/BSD cache flushes
drm/i915: Drop vblank wait from intel_dp_link_down
drm/exynos: fix NULL pointer reference
drm/exynos: remove exynos_plane_dpms
drm/exynos: remove mode property of exynos crtc
drm/exynos: Remove exynos_plane_dpms() call with no effect
drm/i915: Squelch overzealous uncore reset WARN_ON
drm/i915: Take runtime pm reference on hangcheck_info
drm/i915: Correct the IOSF Dev_FN field for IOSF transfers
drm/exynos: fix DMA_ATTR_NO_KERNEL_MAPPING usage
...
This patch is based on exynos-drm-next branch of Inki Dae's tree at:
git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos.git
DECON(Display and Enhancement Controller) is the new IP
in exynos7 SOC for generating video signals using pixel data.
DECON driver can be used to drive 2 different interfaces on Exynos7:
DECON-INT(video controller) and DECON-EXT(Mixer for HDMI)
The existing FIMD driver code was used as a template to create
DECON driver. Only DECON-INT is supported as of now, and
DECON-EXT support will be added later.
The current version of the driver supports video mode displays.
Changelog v2:
- Change config name, DRM_EXYNOS_DECON to DRM_EXYNOS7_DECON.
Signed-off-by: Akshu Agrawal <akshua@gmail.com>
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch changes struct ipu_di_signal_cfg to use struct videomode
to define video timings and flags.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
On some monitors, high resolution modes are not working, exhibiting
pixel column truncation problems (for example, 1280x1024 displays as
1280x1022).
The function ipu_di_adjust_videomode() aims to fix these issues by
adjusting a passed videomode to IPU restrictions. The function can
be called from the drm_crtc_helper_funcs->mode_fixup() methods.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Deepak Das <deepak_das@mentor.com>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
In new model these callbacks are obsolete since the ASoC component
drivers are integrated into the HDMI drivers and no callbacks are
needed anymore.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In omapdss_of_find_source_for_first_ep, we retrieve a source endpoint's DT node,
and then see what omapdss output has the matching device_node pointer in
omap_dss_find_output_by_node.
For all DPI and SDI outputs, the device_node pointer is set as the parent's DSS
device_node pointer. If the source is one of these outputs, the above method
won't work.
To get the correct output for ports within DSS(and in other cases in the future,
where multiple ports might be under one device), we require additional
information which is exclusive to the output port.
We create a new field in omap_dss_device called 'port_num', this provides port
number of the output port corresponding to this device. When searching for the
source endpoint in DT, we extract the 'reg' property from the port corresponding
to the endpoint source. From the list of registered outputs, we pick out that
output which has both dev->of_node and port_num matching with the device_node
pointer and 'reg' of the source endpoint node from DT.
For encoder blocks(the ones which have both an input and output port), we need
to set the port_num as the 'reg' property for the output port as defined in the
DT bindings. We set port_num to 1 in the tfp410 and tpd12s015 encoder drivers.
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* new 6x10 font
* various small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f13d
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- new 6x10 font
- various small fixes and cleanups
* tag 'fbdev-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (30 commits)
fonts: Add 6x10 font
videomode: provide dummy inline functions for !CONFIG_OF
video/atmel_lcdfb: Introduce regulator support
fbdev: sh_mobile_hdmi: Re-init regs before irq re-enable on resume
framebuffer: fix screen corruption when copying
framebuffer: fix border color
arm, fbdev, omap2, LLVMLinux: Remove nested function from omapfb
arm, fbdev, omap2, LLVMLinux: Remove nested function from omap2 dss
video: fbdev: valkyriefb.c: use container_of to resolve fb_info_valkyrie from fb_info
video: fbdev: pxafb.c: use container_of to resolve pxafb_info/layer from fb_info
video: fbdev: cyber2000fb.c: use container_of to resolve cfb_info from fb_info
video: fbdev: controlfb.c: use container_of to resolve fb_info_control from fb_info
video: fbdev: sa1100fb.c: use container_of to resolve sa1100fb_info from fb_info
video: fbdev: stifb.c: use container_of to resolve stifb_info from fb_info
video: fbdev: sis: sis_main.c: Cleaning up missing null-terminate in conjunction with strncpy
video: valkyriefb: Fix unused variable warning in set_valkyrie_clock()
video: fbdev: use %*ph specifier to dump small buffers
video: mx3fb: always enable BACKLIGHT_LCD_SUPPORT
video: fbdev: au1200fb: delete double assignment
video: fbdev: sis: delete double assignment
...
If CONFIG_OF is disabled but we build any driver that tries to
use of_get_display_timing, we get this link error:
ERROR: "of_get_display_timing" [drivers/gpu/drm/rcar-du/rcar-du-drm.ko] undefined!
This adds an empty inline function as an alternative, to avoid changing
each driver using this function when we want to build them without
CONFIG_OF.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adds ipu_dump() which dumps IPU register state to debug.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds ipu_cpmem_dump() which dumps a channel's cpmem to debug.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add a second buffer physaddr to struct ipu_image, for double-buffering
support.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds ipu_cpmem_set_axi_id() to set which AXI bus master the channel
will use to transfer data onto AXI bus.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds ipu_idmac_lock_enable(), which enables or disables channel
burst locking.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds the function ipu_idmac_enable_watermark(), which enables or disables
watermarking in the IDMAC channel. Enabling watermarking can increase a
channel's AXI bus arbitration priority.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds ipu_stride_to_bytes(), which converts a pixel stride to bytes,
suitable for passing to cpmem.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add the reverse of ipu_idmac_select_buffer(), that is, clear a buffer
ready status in a channel.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add ipu_idmac_buffer_is_ready(), returns true if the given buffer in
the given channel is set ready (owned by IPU), or false if not ready
(owned by CPU core).
Support has been added for third buffer, there is no support yet for
triple-buffering in idmac channels, but this function checks
buffer-ready for third buffer in case this support is added later.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Move the IDMAC channel names to imx-ipu-v3.h, to make the names
available outside IPU. Add a couple new channels in the process
(async display BG/FG, channels 24 and 29).
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add simple helper function returning true if passed pixel format is one
of supported planar ones.
Signed-off-by: Dmitry Eremin-Solenikov <dmitry_eremin@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add two functions:
- ipu_degrees_to_rot_mode(): converts a degrees, hflip, and vflip setting
to an IPU rotation mode.
- ipu_rot_mode_to_degrees(): converts an IPU rotation mode with given hflip
and vflip settings to degrees.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Add ipu_mbus_code_to_colorspace() to find ipu_color_space from a
media bus pixel format code.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds ipu_smfc_set_watermark() which programs a channel's SMFC FIFO
levels at which the watermark signal is set and cleared.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Convert the smfc object to be specific to a single smfc channel.
Add ipu_smfc_{get|put} to retrieve and release a single smfc channel
for exclusive use, and add use counter to ipu_smfc_{enable|disable}.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds the Image Converter (IC) unit.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Condensed the three CSC setup functions into a single one that
uses static tables to set up the CSC task parameters.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds the Camera Sensor Interface (CSI) unit required for video capture.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Removed the unused clk_get_rate in ipu_csi_init_interface and the
ipu_csi_ccir_err_detection_enable/disable functions.
Checkpatch cleanup.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Adds two new functions, ipu_set_csi_src_mux() and ipu_set_ic_src_mux(),
that select the inputs to the CSI and IC respectively. Both muxes are
programmed in the IPU_CONF register.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Move channel parameter memory setup functions and macros into a new
submodule ipu-cpmem. In the process, cleanup arguments to the functions
to take a channel pointer instead of a pointer into cpmem for that
channel. That allows the structure of the parameter memory to be
private to ipu-cpmem.c.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
* Much better HDMI infoframe support for OMAP
* Cirrus Logic CLPS711X framebuffer driver
* DT support for PL11x CLCD driver
* Various small fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gXX+
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev updates from Tomi Valkeinen:
- much better HDMI infoframe support for OMAP
- Cirrus Logic CLPS711X framebuffer driver
- DT support for PL11x CLCD driver
- various small fixes
* tag 'fbdev-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (35 commits)
OMAPDSS: DSI: fix depopulating dsi peripherals
video: hyperv: hyperv_fb: refresh the VM screen by force on VM panic
video: ARM CLCD: Fix DT-related build problems
drivers: video: fbdev: atmel_lcdfb.c: Add ability to inverted backlight PWM.
video: ARM CLCD: Add DT support
drm/omap: Add infoframe & dvi/hdmi mode support
OMAPDSS: HDMI: remove the unused code
OMAPDSS: HDMI5: add support to set infoframe & HDMI mode
OMAPDSS: HDMI4: add support to set infoframe & HDMI mode
OMAPDSS: HDMI: add infoframe and hdmi_dvi_mode fields
OMAPDSS: add hdmi ops to hdmi-connector and tpd12s015
OMAPDSS: add hdmi ops to hdmi_ops and omap_dss_driver
OMAPDSS: HDMI: remove custom avi infoframe
OMAPDSS: HDMI5: use common AVI infoframe support
OMAPDSS: HDMI4: use common AVI infoframe support
OMAPDSS: Kconfig: select HDMI
OMAPDSS: HDMI: fix name conflict
OMAPDSS: DISPC: clean up dispc_mgr_timings_ok
OMAPDSS: DISPC: reject interlace for lcd out
OMAPDSS: DISPC: fix debugfs reg dump
...
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
To support MIPI command mode based I80 interface panel,
FIMD should do followings:
- Sets LCD I80 interface timings configuration.
- Uses "lcd_sys" as an IRQ resource and sets relevant IRQ configuration.
- Sets LCD block configuration for I80 interface.
- Sets ideal(pixel) clock is 2 times faster than the original one
to generate frame done IRQ prior to the next TE signal.
- Implements trigger feature that transfers image data if there is page
flip request, and implements TE handler to call trigger function.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch removes fimd and fb codes for s5pc100 SoC.
Acked-by: Jingoo Han <jg1.han@samsung.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add two new ops for HDMI: set_infoframe() and set_hdmi_mode(). The first
one can be used to specify the infoframe that should be sent to the HDMI
monitor, and the second one is used to enable HDMI mode (versus DVI
mode).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pull drm updates from Dave Airlie:
"This is the main drm merge window pull request, changes all over the
place, mostly normal levels of churn.
Highlights:
Core drm:
More cleanups, fix race on connector/encoder naming, docs updates,
object locking rework in prep for atomic modeset
i915:
mipi DSI support, valleyview power fixes, cursor size fixes,
execlist refactoring, vblank improvements, userptr support, OOM
handling improvements
radeon:
GPUVM tuning and large page size support, gart fixes, deep color
HDMI support, HDMI audio cleanups
nouveau:
- displayport rework should fix lots of issues
- initial gk20a support
- gk110b support
- gk208 fixes
exynos:
probe order fixes, HDMI changes, IPP consolidation
msm:
debugfs updates, misc fixes
ast:
ast2400 support, sync with UMS driver
tegra:
cleanups, hdmi + hw cursor for Tegra 124.
panel:
fixes existing panels add some new ones.
ipuv3:
moved from staging to drivers/gpu"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (761 commits)
drm/nouveau/disp/dp: fix tmds passthrough on dp connector
drm/nouveau/dp: probe dpcd to determine connectedness
drm/nv50-: trigger update after all connectors disabled
drm/nv50-: prepare for attaching a SOR to multiple heads
drm/gf119-/disp: fix debug output on update failure
drm/nouveau/disp/dp: make use of postcursor when its available
drm/g94-/disp/dp: take max pullup value across all lanes
drm/nouveau/bios/dp: parse lane postcursor data
drm/nouveau/dp: fix support for dpms
drm/nouveau: register a drm_dp_aux channel for each dp connector
drm/g94-/disp: add method to power-off dp lanes
drm/nouveau/disp/dp: maintain link in response to hpd signal
drm/g94-/disp: bash and wait for something after changing lane power regs
drm/nouveau/disp/dp: split link config/power into two steps
drm/nv50/disp: train PIOR-attached DP from second supervisor
drm/nouveau/disp/dp: make use of existing output data for link training
drm/gf119/disp: start removing direct vbios parsing from supervisor
drm/nv50/disp: start removing direct vbios parsing from supervisor
drm/nouveau/disp/dp: maintain receiver caps in response to hpd signal
drm/nouveau/disp/dp: create subclass for dp outputs
...
This patch registers the two CSI platform devices per IPU.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
IPU_CONF_..._EN bits are implementation details, not to be made public.
Add wrappers around ipu_module_enable/disable, so the CSI V4L2 driver
can enable/disable the CSI and SMFC modules.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
This function returns the currently active buffer (0 or 1)
of a double buffered IDMAC channel. It is to be used by the
CSI driver.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The Sensor Multi Fifo Controller (SMFC) is used as a buffer between
the two CSIs (writing simultaneously) and up to four IDMAC channels.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
The i.MX Image Processing Unit (IPU) contains a number of image processing
blocks that sit right in the middle between DRM and V4L2. Some of the modules,
such as Display Controller, Processor, and Interface (DC, DP, DI) or CMOS
Sensor Interface (CSI) and their FIFOs could be assigned to either framework,
but others, such as the dma controller (IDMAC) and image converter (IC) can
be used by both.
The IPUv3 core driver provides an internal API to access the modules, to be
used by both DRM and V4L2 IPUv3 drivers.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add DSS features for AM43xx.
Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Macros to_dss_driver() and to_dss_device() are no longer used, and the
latter doesn't even work. Remove them.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
If LPAE is enabled, dma_addr_t is 64 bit, so we have to
change a few type for everything in this driver to match
again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
This contains OMAP related fbdev changes for 3.15. The bulk of the patches are
for adding Device Tree support for OMAP Display Subsystem:
* SoCs: OMAP2/3/4
* Boards: OMAP4 Panda, OMAP4 SDP, OMAP3 Beagle, OMAP3 Beagle-xM, OMAP3
IGEP0020, OMAP3 N900
* Devices: TFP410 Encoder, tpd12s015 HDMI companion chip, Sony acx565akm panel,
MIPI DSI Command mode panel and HDMI, DVI and Analog TV connectors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=Mnc1
-----END PGP SIGNATURE-----
Merge tag 'fbdev-omap-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull OMAP fbdev changes from Tomi Valkeinen:
"This is based on the already pulled fbdev-main changes, and this also
merges .dts branch from Tony Lindgren (which has also been pulled), so
that I was able to add the display related .dts changes.
This contains OMAP related fbdev changes for 3.15. The bulk of the
patches are for adding Device Tree support for OMAP Display Subsystem:
- SoCs: OMAP2/3/4
- Boards: OMAP4 Panda, OMAP4 SDP, OMAP3 Beagle, OMAP3 Beagle-xM,
OMAP3 IGEP0020, OMAP3 N900
- Devices: TFP410 Encoder, tpd12s015 HDMI companion chip, Sony
acx565akm panel, MIPI DSI Command mode panel and HDMI, DVI and
Analog TV connectors"
* tag 'fbdev-omap-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (45 commits)
OMAPDSS: HDMI: fix interlace output
OMAPDSS: add missing __init for dss_init_ports
ARM: OMAP2+: remove pdata quirks for displays
OMAPDSS: remove DT hacks for regulators
Doc/DT: Add DT binding documentation for tpd12s015 encoder
Doc/DT: Add DT binding documentation for TFP410 encoder
Doc/DT: Add DT binding documentation for Sony acx565akm panel
Doc/DT: Add DT binding documentation for MIPI DSI CM Panel
Doc/DT: Add DT binding documentation for HDMI Connector
Doc/DT: Add DT binding documentation for DVI Connector
Doc/DT: Add DT binding documentation for Analog TV Connector
ARM: omap3-n900.dts: add display information
ARM: omap3-igep0020.dts: add display information
ARM: omap3-beagle-xm.dts: add display information
ARM: omap3-beagle.dts: add display information
ARM: omap4-sdp.dts: add display information
Doc/DT: Add DT binding documentation for OMAP DSS
OMAPDSS: acx565akm: Add DT support
OMAPDSS: connector-analog-tv: Add DT support
OMAPDSS: hdmi-connector: Add DT support
...
Various fbdev fixes and improvements, but nothing big.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=bavN
-----END PGP SIGNATURE-----
Merge tag 'fbdev-main-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev changes from Tomi Valkeinen:
"Various fbdev fixes and improvements, but nothing big"
* tag 'fbdev-main-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (38 commits)
fbdev: Make the switch from generic to native driver less alarming
Video: atmel: avoid the id of fix screen info is overwritten
video: imxfb: Add DT default contrast control register property.
video: atmel_lcdfb: ensure the hardware is initialized with the correct mode
fbdev: vesafb: add dev->remove() callback
fbdev: efifb: add dev->remove() callback
video: pxa3xx-gcu: switch to devres functions
video: pxa3xx-gcu: provide an empty .open call
video: pxa3xx-gcu: pass around struct device *
video: pxa3xx-gcu: rename some symbols
sisfb: fix 1280x720 resolution support
video: fbdev: uvesafb: Remove impossible code path in uvesafb_init_info
video: fbdev: uvesafb: Remove redundant NULL check in uvesafb_remove
fbdev: FB_OPENCORES should depend on HAS_DMA
OMAPDSS: convert pixel clock to common videomode style
OMAPDSS: Remove unused get_context_loss_count support
OMAPDSS: use DISPC register to detect context loss
video: da8xx-fb: Use "SIMPLE_DEV_PM_OPS" macro
video: imxfb: Convert to SIMPLE_DEV_PM_OPS
video: imxfb: Resolve mismatch between backlight/contrast
...
Add helpers to get ports and endpoints from DT data.
These helpers parse v4l2 style ports and endpoints, but compared to the
v4l2 helpers, these allow iterating ports and endpoints separately.
This is a temporary solution until we get generic code to parse the
ports and endpoints.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
omapdss has its own video-timings struct, but we want to move the common
videomode.
The first step is to change the omapdss's pixelclock unit from kHz to
Hz. Also, omapdss uses "pixel_clock" field name, whereas the common
videomode uses "pixelclock" field name. This patch changes the field
name also, as that makes it easy to spot any non-converted pixel_clock
uses.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omapdss driver no longer uses get_context_loss_count call, so we can
remove it.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
The SGI Visual Workstation seems to be dead; remove support so we
don't have to continue maintaining it.
Cc: Andrey Panin <pazke@donpac.ru>
Cc: Michael Reed <mdr@sgi.com>
Link: http://lkml.kernel.org/r/530CFD6C.7040705@zytor.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Nothing particularly stands out in this pull request. The biggest part of the
changes are cleanups.
Maybe one fix to mention is the "fb: reorder the lock sequence to fix potential
dead lock" which hopefully fixes the fb locking issues reported by multiple
persons.
There are also a few commits that have changes to arch/arm/mach-at91 and
arch/avr32, which have been acked by the maintainers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=59+j
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev changes from Tomi Valkeinen:
"Nothing particularly stands out in this pull request. The biggest
part of the changes are cleanups.
Maybe one fix to mention is the "fb: reorder the lock sequence to fix
potential dead lock" which hopefully fixes the fb locking issues
reported by multiple persons.
There are also a few commits that have changes to arch/arm/mach-at91
and arch/avr32, which have been acked by the maintainers"
* tag 'fbdev-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (143 commits)
fb: reorder the lock sequence to fix potential dead lock
fbdev: shmobile-lcdcfb: Convert to clk_prepare/unprepare
fbdev: shmobile-hdmi: Convert to clk_prepare/unprepare
omapdss: Add new panel driver for Topolly td028ttec1 LCD.
video: exynos_mipi_dsi: Unlock the mutex before returning
video: da8xx-fb: remove unwanted define
video: Remove unnecessary semicolons
simplefb: use write-combined remapping
simplefb: fix unmapping fb during destruction
OMAPDSS: connector-dvi: fix releasing i2c_adapter
OMAPDSS: DSI: fix perf measuring ifdefs
framebuffer: Use fb_<level>
framebuffer: Add fb_<level> convenience logging macros
efifb: prevent null-deref when iterating dmi_list
fbdev: fix error return code in metronomefb_probe()
video: xilinxfb: Fix for "Use standard variable name convention"
OMAPDSS: Fix de_level in videomode_to_omap_video_timings()
video: xilinxfb: Simplify error path
video: xilinxfb: Use devm_kzalloc instead of kzalloc
video: xilinxfb: Use standard variable name convention
...
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
[tomi.valkeinen@ti.com: made a few funcs static]
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Exynos Display Port can be used only for Exynos SoCs. In addition,
non-DT for EXYNOS SoCs is not supported from v3.11; thus, there is
no need to support non-DT for Exynos Display Port.
The 'include/video/exynos_dp.h' file has been used for non-DT
support and the content of file include/video/exynos_dp.h is moved
to drivers/video/exynos/exynos_dp_core.h. Thus, the 'exynos_dp.h'
file is removed. Also, 'struct exynos_dp_platdata' is removed,
because it is not used any more.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the generic PHY API instead of the platform callback
for the MIPI DSIM DPHY enable/reset control.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Donghwa Lee <dh09.lee@samsung.com>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
so we can use have list gpio as example (probe via DT)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Today we mix pdata and drivers data in the struct atmel_lcdfb_info
Fix it and introduce a new struct atmel_lcdfb_pdata for platform data only
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add pitch length info of graphics/video layer, pitch is used
to represent line length in byte, the usage depends on pix_fmt.
If the fmt is YUV, the pitch[0] will be Y length,pitch[1]
will be U length, pitch[2] will be V lenth.
If the fmt is RGB, the picth[0] will be line lenth, and
pitch[1]/pitch[2] will be 0 and not be used.
Signed-off-by: Jing Xiang <jxiang@marvell.com>
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Zhou Zhu <zzhu3@marvell.com>
Reviewed-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We could set rb swap in two modules: DMA controler input part and
dsi interface output part.
DMA input part is based on pix_fmt to set rbswap, dsi output interface
part will set rbswap based on platform dsi_rbswap configuration.
This patch include below change and enhancement:
1) The input format which support rbswap is based on RGB format,
eg. RGB565 indicates the source data in memory is that Red is [15~11],
Green is [10~5], Blue is [4:0], Red is MSB, Blue is LSB, but for the
display dma input default setting(rbswap = 0), it only support Blue
is [15~11], Green is [10~5], Red is [4:0], Red is LSB, Blue is MSB,
so for this format(RGB565), display controller need to set rbswap
= 1 and it can support the MSB/LSB correctly.
BGR/YUV format will not set it in mmp display driver.
2) The dsi output part of rbswap is depend on dsi_rbswap which is
defined in specific platfrom. For output dsi interface, it has this
feature to do rbswap again if it needs specifc byte sequence of RGB
byte for DSI panel.
eg. If display content is set RGB565 in memory and DMA input part set
rbswap in driver to support Red as MSB , Blue LSB, but dsi panel only
support Red as LSB, Blue as MSB, then it can use this feature.
If there is no this requirement of panel, this dsi output part is not
needed.
Signed-off-by: Guoqing Li <ligq@marvell.com>
Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Zhou Zhu <zzhu3@marvell.com>
Reviewed-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
* Improvements to da8xx-fb to make it support v2 of the LCDC IP, used e.g. in
BeagleBone
* Himax HX8369 controller support
* Various small fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSKB9vAAoJEPo9qoy8lh71dqkP/AgEljWrEKumJ6KQYLjxGEQM
RseTYKaNE78TkPX5p4DcA2rJ0Ud/yK/swelZvHfnq+6yTxUiuwsHDAPcgrMf27NM
yWWTW0gJRrs7jbHF7sIQkPbww56Irjz7uzUfOoNRqajgf51+mB3olAhTUn9tE3Pf
PW9u5M5b904VnT0VKASEUB9SUtx5izWKP9Yyy7QG8WF++zp4BHfmO7+8kx46cE0l
WFAQL7JrvtzI2yVcnnkfDRpmHOunbupIGOAT79s3KlK226SHNRi3wd6w6zDTudjj
sEMJLDpipKYliT+yzwgHmuHfDTi+gx6a36bTMf9lXp+KZKYEjNlWnYKKHdkdtk7Z
nYlUagu+8tOUsZGy5dOyMkbeYMMfpcBlN1VjMDBIs1kPc0psg15wPznLdnPa5rau
Ag0Z7GPHvy8ucFBsfqp1Sgsi1QMSqWgkcCh55BAMID58A7ELPhHz9NpaFt9KGMEy
EKoNPQmTjIosgEQDdbayqjBwBqK1O0Q8MPPFGiDCwX37XppgZ4mflSz3NfDpwN+J
+J+C3y2Bn2qzYPUzy3vOoohoWvtxsGnteNyX3D/Yrk7I4/4IWdI0maTVMv9yq//D
/uBt+OxEY0ODkfC+yhhKT6P5zNBqsoWa16fqDdx3WDV7xoCsVq6dKkhaQd/zEr0Z
Yjtcw3ZRyGLQgX75Zo+B
=Kr2i
-----END PGP SIGNATURE-----
Merge tag 'fbdev-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev changes from Tomi Valkeinen:
- Improvements to da8xx-fb to make it support v2 of the LCDC IP, used
eg in BeagleBone
- Himax HX8369 controller support
- Various small fixes and cleanups
* tag 'fbdev-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (42 commits)
video: da8xx-fb: fix the polarities of the hsync/vsync pulse
video: da8xx-fb: support lcdc v2 timing register expansion
video: da8xx-fb: fixing timing off by one errors
video: da8xx-fb fixing incorrect porch mappings
video: xilinxfb: replace devm_request_and_ioremap by devm_ioremap_resource
fbmem: move EXPORT_SYMBOL annotation next to symbol declarations
drivers: video: fbcmap: remove the redundency and incorrect checkings
video: mxsfb: simplify use of devm_ioremap_resource
Release efifb's colormap in efifb_destroy()
at91/avr32/atmel_lcdfb: prepare clk before calling enable
video: exynos: Ensure definitions match prototypes
OMAPDSS: fix WARN_ON in 'alpha_blending_enabled' sysfs file
OMAPDSS: HDMI: Fix possible NULL reference
video: da8xx-fb: adding am33xx as dependency
video: da8xx-fb: let compiler decide what to inline
video: da8xx-fb: make clock naming consistent
video: da8xx-fb: set upstream clock rate (if reqd)
video: da8xx-fb: reorganize panel detection
video: da8xx-fb: ensure non-null cfg in pdata
video: da8xx-fb: use devres
...
In the old panel device model we had omap_dss_output entities,
representing the encoders in the DSS block. This entity had "device"
field, which pointed to the panel that was using the omap_dss_output.
With the new panel device model, the omap_dss_output is integrated into
omap_dss_device, which now represents a "display entity". Thus the "device"
field, now in omap_dss_device, points to the next entity in the display
entity-chain.
This patch renames the "device" field to "dst", which much better tells
what the field points to.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
In the old panel device model we had "outputs", which were the encoders
inside OMAP DSS block, and panel devices (omap_dss_device). The panel
devices had a reference to the source of the video data, i.e. reference
to an "output", in a field named "output".
That was somewhat confusing even in the old panel device model, but even
more so with the panel device model where we can have longer chains of
display entities.
This patch renames the "output" field to "src", which much better tells
what the field points to.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
With all the old panels removed and all the old panel model APIs removed
from the DSS encoders, we can now remove the custom omapdss-bus which
was used in the old panel model.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Now that the old panel drivers have been removed, we can remove the
old-model API and related code from the DSS encoder drivers.
This patch removes the code from the RFBI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Now that the old panel drivers have been removed, we can remove the
old-model API and related code from the DSS encoder drivers.
This patch removes the code from the SDI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Now that the old panel drivers have been removed, we can remove the
old-model API and related code from the DSS encoder drivers.
This patch removes the code from the DSI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Now that the old panel drivers have been removed, we can remove the
old-model API and related code from the DSS encoder drivers.
This patch removes the code from the DPI driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
The board files now use the new panel drivers, making the old panel
drivers obsolete.
Remove the old panel drivers, Kconfig and Makefile entries, and the
panels' platform data structs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
The 'channel' field in struct omap_dss_device is no longer used, and can
be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Change the lcd_disable_raster funtion from using a bool to an enum
as the function is very confusing with the current api. This helps
make it clearer what the parameter is really doing.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
This is the second part of OMAP DSS changes for 3.11. This part contains the
new DSS device model support.
The current OMAP panel drivers use a custom DSS bus, and there's a hard limit
of one external display block per video pipeline. In the new DSS device model
the devices/drivers are made according to the control bus of the display block,
usually platform, i2c or spi. The display blocks can also be chained so that we
can have separate drivers for setups with both external encoder and panel.
To allow the current board files, which use the old style panels, to function,
the old display drivers are left in their current state, and new ones are added
to drivers/video/omap2/displays-new/. When the board files have been converted
to use the new style panels, we can remove the old code. This is planned to
happen in v3.12.
Having to support two very different DSS device models makes the driver
somewhat confusing in some parts, and prevents us from properly cleaning up
some other parts. These cleanups will be done when the old code is removed.
The new device model is designed with CDF (Common Display Framework) in mind.
While CDF is still under work, the new DSS device model should be much more
similar to CDF's model than the old device model, which should make the
eventual conversion to CDF much easier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yEcM
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.11-2' of git://gitorious.org/linux-omap-dss2/linux into fbdev/for-next
OMAP display subsystem changes for 3.11 (part 2/2)
This is the second part of OMAP DSS changes for 3.11. This part contains the
new DSS device model support.
The current OMAP panel drivers use a custom DSS bus, and there's a hard limit
of one external display block per video pipeline. In the new DSS device model
the devices/drivers are made according to the control bus of the display block,
usually platform, i2c or spi. The display blocks can also be chained so that we
can have separate drivers for setups with both external encoder and panel.
To allow the current board files, which use the old style panels, to function,
the old display drivers are left in their current state, and new ones are added
to drivers/video/omap2/displays-new/. When the board files have been converted
to use the new style panels, we can remove the old code. This is planned to
happen in v3.12.
Having to support two very different DSS device models makes the driver
somewhat confusing in some parts, and prevents us from properly cleaning up
some other parts. These cleanups will be done when the old code is removed.
The new device model is designed with CDF (Common Display Framework) in mind.
While CDF is still under work, the new DSS device model should be much more
similar to CDF's model than the old device model, which should make the
eventual conversion to CDF much easier.
This is the first part of OMAP DSS changes for 3.11. This part contains fixes,
cleanups and reorganizations that are not directly related to the new DSS
device model that is added in part 2, although many of the reorganizations are
made to make the part 2 possible.
There should not be any functional changes visible to the user except the few
bug fixes.
The main new internal features:
- Display (dis)connect support, which allows us to explicitly (dis)connect a
whole display pipeline
- Panel list, which allows us to operate without the specific DSS bus
- Combine omap_dss_output to omap_dss_device, so that we have one generic
"entity" for display pipeline blocks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=I6Y2
-----END PGP SIGNATURE-----
Merge tag 'omapdss-for-3.11-1' of git://gitorious.org/linux-omap-dss2/linux into fbdev/for-next
OMAP display subsystem changes for 3.11 (part 1/2)
This is the first part of OMAP DSS changes for 3.11. This part contains fixes,
cleanups and reorganizations that are not directly related to the new DSS
device model that is added in part 2, although many of the reorganizations are
made to make the part 2 possible.
There should not be any functional changes visible to the user except the few
bug fixes.
The main new internal features:
- Display (dis)connect support, which allows us to explicitly (dis)connect a
whole display pipeline
- Panel list, which allows us to operate without the specific DSS bus
- Combine omap_dss_output to omap_dss_device, so that we have one generic
"entity" for display pipeline blocks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEbBAABAgAGBQJRxf9cAAoJEHm+PkMAQRiGMWkH911xM4gRmFgE7SqVW4F4AWBm
ngcqMqNy9IdqKfibORUUDvVfEa5gjD5ai2quIKpfQiaukbpQJ696H90ijuAkajLn
DQBrN243s0pzhhc/quWINnWxsFQ613JjdUMUMaD7e9A1aKjYzWrPGt/tSjrFXGCP
tArTupVzc/iOmnEQDKiROI/Nokq44QJ36aTGPM7n08xMtpKmkCXM+9/UosBteB0O
HVI33dmjwz7i55fI53XAWyuZCE+gSEnA4z8spJ9LfXso2W14V+roc+GuL6OyeeTI
pCn/+4niVPb4B0ROZlpyVmdZjbPPcMMEK5o+BSJI68SH6LHZTQh2iVuqYfpSyA==
=uUH5
-----END PGP SIGNATURE-----
Merge tag 'v3.10-rc7' into drm-next
Linux 3.10-rc7
The sdvo lvds fix in this -fixes pull
commit c3456fb3e4
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jun 10 09:47:58 2013 +0200
drm/i915: prefer VBT modes for SVDO-LVDS over EDID
has a silent functional conflict with
commit 990256aec2
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri May 31 12:17:07 2013 +0000
drm: Add probed modes in probe order
in drm-next. W simply need to add the vbt modes before edid modes, i.e. the
other way round than now.
Conflicts:
drivers/gpu/drm/drm_prime.c
drivers/gpu/drm/i915/intel_sdvo.c
Commit ffa3fd21de ("videomode: implement public of_get_display_timing()") causes
the following build warning:
include/video/of_display_timing.h:18:10: warning: 'struct display_timing' declared inside parameter list [enabled by default]
include/video/of_display_timing.h:18:10: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Declare 'display_timing' to avoid the build warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add TPO TD043MTEA1 panel driver which uses the new DSS device model
and DSS ops.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Add Sony ACX565AKM panel driver which uses the new DSS device model and
DSS ops.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Add DSI Command Mode panel driver which uses the new DSS device model
and DSS ops. This driver only supports a very basic set of features
which should be common to all DSI command mode panels.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add simple DPI Panel driver which uses the new DSS device model and DSS
ops. A "simple" panel means one that does not require any special setup.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add TPD12S015 HDMI ESD protection and level shifter encoder driver which
uses the new DSS device model and DSS ops.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "ops" style method for using DSI functionality.
Ops style calls will allow us to have arbitrarily long display
pipelines, where each entity can call ops in the previous display
entity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "ops" style method for using HDMI functionality.
Ops style calls will allow us to have arbitrarily long display
pipelines, where each entity can call ops in the previous display
entity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "ops" style method for using analog TV functionality.
Ops style calls will allow us to have arbitrarily long display
pipelines, where each entity can call ops in the previous display
entity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "ops" style method for using DVI functionality.
Ops style calls will allow us to have arbitrarily long display
pipelines, where each entity can call ops in the previous display
entity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "ops" style method for using SDI functionality.
Ops style calls will allow us to have arbitrarily long display
pipelines, where each entity can call ops in the previous display
entity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add "ops" style method for using DPI functionality.
Ops style calls will allow us to have arbitrarily long display
pipelines, where each entity can call ops in the previous display
entity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add new display bus type for DVI. This is not used by omapdss driver
itself, but is used by external encoder chips that output DVI.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
In order to allow multiple display block in a video pipeline, we need to
give the drivers way to register themselves. For now we have
the omapdss_register_display() which is used to register panels, and
dss_register_output() which is used to register DSS encoders.
This patch makes dss_register_output() public (with the name of
omapdss_register_output), which can be used to register also external
encoders. The distinction between register_output and register_display
is that a "display" is an entity at the end of the videopipeline, and
"output" is something inside the pipeline.
The registration and naming will be made saner in the future, but the
current names and functions are kept to minimize changes during the dss
device model transition.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The use of platform callbacks, backlight, DSI TE and reset gpio from the
struct omap_dss_device has been removed. We can thus remove the fields
from omap_dss_device.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
omap_dss_get_device() should be called for omap_dss_device before it is
used to increase its refcount. Currently we only increase the refcount
for the underlying device.
This patch adds managing the ref count to the underlying module also,
which contains the ops for the omap_dss_device.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add struct module *owner field to omap_dss_device, which points to the
module containing the ops for this omap_dss_device. This will be used to
manage the ref count for the module.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently have omap_dss_device, which represents an external display
device, sometimes an external encoder, sometimes a panel. Then we have
omap_dss_output, which represents DSS's output encoder.
In the future with new display device model, we construct a video
pipeline from the display blocks. To accomplish this, all the blocks
need to be presented by the same entity.
Thus, this patch combines omap_dss_output into omap_dss_device. Some of
the fields in omap_dss_output are already found in omap_dss_device, but
some are not. This means we'll have DSS output specific fields in
omap_dss_device, which is not very nice. However, it is easier to just
keep those output specific fields there for now, and after transition to
new display device model is made, they can be cleaned up easier than
could be done now.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_dss_start_device() and omap_dss_stop_device(), called by the
DSS output drivers, are old relics. They originally did something
totally else, but nowadays they increase the module ref count for panels
that are enabled.
This model is quite broken: the panel modules may be used even before
they are enabled. For example, configuring the panel requires calls to
functions located in the panel modules.
In the following patches we try to improve the ref count management for
the modules and display devices. The first step, however, is to remove
the omap_dss_start/stop_device() totally.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We are about to remove the dss bus support, which also means that the
omap_dss_device won't be a real device anymore. This means that the
embedded "dev" struct needs to be removed from omap_dss_device.
After we've finished the removal of the dss bus, we see the following
changes:
- struct omap_dss_device won't be a real Linux device anymore, but more
like a "display entity".
- struct omap_dss_driver won't be a Linux device driver, but "display
entity ops".
- The panel devices/drivers won't be omapdss devices/drivers, but
platform/i2c/spi/etc devices/drivers, whichever fits the control
mechanism of the panel.
- The panel drivers will create omap_dss_device and omap_dss_driver,
fill the required fields, and register the omap_dss_device to
omapdss.
- omap_dss_device won't have an embedded dev struct anymore, but a
dev pointer to the actual device that manages the omap_dss_device.
The model described above resembles the model that has been discussed
with CDF (common display framework).
For the duration of the conversion, we temporarily have two devs in the
dssdev, the old "old_dev", which is a full embedded device struct, and the
new "dev", which is a pointer to the device. "old_dev" will be removed
in the future.
For devices belonging to dss bus the dev is initialized to point to
old_dev. This way all the code can just use the dev, for both old and
new style panels.
Both the new and old style panel drivers work during the conversion, and
only after the dss bus support is removed will the old style panels stop
to compile.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently use the omapdss bus (which contains all the available
displays) to iterate the displays. As the omapdss bus is on its way out,
this needs to be changed.
Instead of using the dss bus to iterate displays, this patch adds our
own list of displays which we manage. The panels on the dss bus are
automatically added to this new list.
An "alias" field is also added to omap_dss_device. This field is
set to "display%d", the same way as omap_dss_device's dev name is set.
This alias is later used to keep backward compatibility, when the
embedded dev is no longer used.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add helper functions to convert between omapdss specific video timings
and the common videomode.
Eventually omapdss will be changed to use only the common video timings,
and these helper functions will make the transition easier.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We currently have two steps in panel initialization and startup: probing
and enabling. After the panel has been probed, it's ready and can be
configured and later enabled.
This model is not enough with more complex display pipelines, where we
may have, for example, two panels, of which only one can be used at a
time, connected to the same video output.
To support that kind of scenarios, we need to add new step to the
initialization: connect.
This patch adds support for connecting and disconnecting panels. After
probe, but before connect, no panel ops should be called. When the
connect is called, a proper video pipeline is established, and the panel
is ready for use. If some part in the video pipeline is already
connected (by some other panel), the connect call fails.
One key difference with the old style setup is that connect() handles
also connecting to the overlay manager. This means that the omapfb (or
omapdrm) no longer needs to figure out which overlay manager to use, but
it can just call connect() on the panel, and the proper overlay manager
is connected by omapdss.
This also allows us to add back the support for dynamic switching
between two exclusive panels. However, the current panel device model is
not changed to support this, as the new device model is implemented in
the following patches and the old model will be removed. The new device
model supports dynamic switching.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add two helper functions that can be used to find either the DSS output
or the overlay manager that is connected to the given display.
This hides how the output and the manager are actually connected, making
it easier to change the connections in the future.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a support function to find a DSS output by given DT node. This is
used in later patches to link the panels to DSS outputs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Add a support function to find a DSS output by given name. This is used
in later patches to link the panels to DSS outputs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We can currently set the default display (i.e. the initial display) in
the omapdss platform data by using a pointer to the default
omap_dss_device. Internally omapdss uses the device's name to resolve
the default display.
As it's difficult to get the omap_dss_device pointer in the future,
after we've changed the omapdss device model, this patch adds a new way
to define the default display, by using the name of the display.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
The old code allowed very strange memory types. Now it works like
all the other video drivers: ioremap_wc is used unconditionally,
and MTRRs are set if PAT is unavailable (unless MTRR is disabled
by a module parameter).
UC, WB, and WT support is gone. If there are MTRR conflicts that prevent
addition of a WC MTRR, adding a non-conflicting MTRR is pointless; it's
better to just turn off MTRR support entirely.
As an added bonus, any MTRR added is freed on unload.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current of_get_display_timings() reads multiple display timings,
allocating memory for the entries. However, most of the time when
parsing display timings from DT data is needed, there's only one display
timing as it's not common for a LCD panel to support multiple videomodes.
This patch creates a new function:
int of_get_display_timing(struct device_node *np, const char *name,
struct display_timing *dt);
which can be used to parse a single display timing entry from the given
node name.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
When booting with DT, there's a crash when omapfb is probed. This is
caused by the fact that omapdss+DT is not yet supported, and thus
omapdss is not probed at all. On the other hand, omapfb is always
probed. When omapfb tries to use omapdss, there's a NULL pointer
dereference crash. The same error should most likely happen with omapdrm
and omap_vout also.
To fix this, add an "initialized" state to omapdss. When omapdss has
been probed, it's marked as initialized. omapfb, omapdrm and omap_vout
check this state when they are probed to see that omapdss is actually
there.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem
specific interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into
platform specific interface, or to get called from platform specific
code, as long as all information about the hardware is provided
through a device tree.
Most of the drivers we touch this time are for clocksource. Since
now most of them are part of drivers/clocksource, I expect that we
won't have to touch these again from arm-soc and can let the
clocksource maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the
merge conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface
for taking devices on the SoC out of reset or back into reset.
Patches to use this interface on i.MX follow later in this merge
window, and we are going to have other platforms (at least tegra
and sirf) get converted in 3.11. This will let us get rid of
platform specific callbacks in a number of platform independent
device drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ZWk9
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Olof Johansson:
"This is a rather large set of patches for device drivers that for one
reason or another the subsystem maintainer preferred to get merged
through the arm-soc tree. There are both new drivers as well as
existing drivers that are getting converted from platform-specific
code into standalone drivers using the appropriate subsystem specific
interfaces.
In particular, we can now have pinctrl, clk, clksource and irqchip
drivers in one file per driver, without the need to call into platform
specific interface, or to get called from platform specific code, as
long as all information about the hardware is provided through a
device tree.
Most of the drivers we touch this time are for clocksource. Since now
most of them are part of drivers/clocksource, I expect that we won't
have to touch these again from arm-soc and can let the clocksource
maintainers take care of these in the future.
Another larger part of this series is specific to the exynos platform,
which is seeing some significant effort in upstreaming and
modernization of its device drivers this time around, which
unfortunately is also the cause for the churn and a lot of the merge
conflicts.
There is one new subsystem that gets merged as part of this series:
the reset controller interface, which is a very simple interface for
taking devices on the SoC out of reset or back into reset. Patches to
use this interface on i.MX follow later in this merge window, and we
are going to have other platforms (at least tegra and sirf) get
converted in 3.11. This will let us get rid of platform specific
callbacks in a number of platform independent device drivers."
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (256 commits)
irqchip: s3c24xx: add missing __init annotations
ARM: dts: Disable the RTC by default on exynos5
clk: exynos5250: Fix parent clock for sclk_mmc{0,1,2,3}
ARM: exynos: restore mach/regs-clock.h for exynos5
clocksource: exynos_mct: fix build error on non-DT
pinctrl: vt8500: wmt: Fix checking return value of pinctrl_register()
irqchip: vt8500: Convert arch-vt8500 to new irqchip infrastructure
reset: NULL deref on allocation failure
reset: Add reset controller API
dt: describe base reset signal binding
ARM: EXYNOS: Add arm-pmu DT binding for exynos421x
ARM: EXYNOS: Add arm-pmu DT binding for exynos5250
ARM: EXYNOS: Enable PMUs for exynos4
irqchip: exynos-combiner: Correct combined IRQs for exynos4
irqchip: exynos-combiner: Add set_irq_affinity function for combiner_irq
ARM: EXYNOS: fix compilation error introduced due to common clock migration
clk: exynos5250: Fix divider values for sclk_mmc{0,1,2,3}
clk: exynos4: export clocks required for fimc-is
clk: samsung: Fix compilation error
clk: tegra: fix enum tegra114_clk to match binding
...
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 3.10.
Wierd bits:
- OMAP drm changes required OMAP dss changes, in drivers/video, so I
took them in here.
- one more fbcon fix for font handover
- VT switch avoidance in pm code
- scatterlist helpers for gpu drivers - have acks from akpm
Highlights:
- qxl kms driver - driver for the spice qxl virtual GPU
Nouveau:
- fermi/kepler VRAM compression
- GK110/nvf0 modesetting support.
Tegra:
- host1x core merged with 2D engine support
i915:
- vt switchless resume
- more valleyview support
- vblank fixes
- modesetting pipe config rework
radeon:
- UVD engine support
- SI chip tiling support
- GPU registers initialisation from golden values.
exynos:
- device tree changes
- fimc block support
Otherwise:
- bunches of fixes all over the place."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (513 commits)
qxl: update to new idr interfaces.
drm/nouveau: fix build with nv50->nvc0
drm/radeon: fix handling of v6 power tables
drm/radeon: clarify family checks in pm table parsing
drm/radeon: consolidate UVD clock programming
drm/radeon: fix UPLL_REF_DIV_MASK definition
radeon: add bo tracking debugfs
drm/radeon: add new richland pci ids
drm/radeon: add some new SI PCI ids
drm/radeon: fix scratch reg handling for UVD fence
drm/radeon: allocate SA bo in the requested domain
drm/radeon: fix possible segfault when parsing pm tables
drm/radeon: fix endian bugs in atom_allocate_fb_scratch()
OMAPDSS: TFP410: return EPROBE_DEFER if the i2c adapter not found
OMAPDSS: VENC: Add error handling for venc_probe_pdata
OMAPDSS: HDMI: Add error handling for hdmi_probe_pdata
OMAPDSS: RFBI: Add error handling for rfbi_probe_pdata
OMAPDSS: DSI: Add error handling for dsi_probe_pdata
OMAPDSS: SDI: Add error handling for sdi_probe_pdata
OMAPDSS: DPI: Add error handling for dpi_probe_pdata
...
Platform LCD devices may need to do some device-specific initialization
before they can be used (regulator or GPIO setup, for example), but
currently the driver does not support any way of doing this. This patch
adds a probe() callback to plat_lcd_data which platform LCD devices can
set to indicate that device-specific initialization is needed.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The controller also contains support for displays in a portrait
orientation and it seems devices which such displays really reached
the market - Pandigital Novell seems to be one example.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change the driver to use the framebuffer rotation functions to be
able to change the rotation at runtime.
This also removes the setting of the rotation via the platform data.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The n8x0 panel contains support to call platform backlight functions.
These are not used by any board, and can be removed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Use the new clock calculation code in the DSI driver.
The new code does not need DSI video mode parameters from the panel
driver, like the old code does. Instead the new code is given the normal
video timings, and a few DSI parameters, which are used to create DSI
video timings.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of managing DSI sync ends with booleans, add an enum for the DSI
transfer mode. This is much cleaner way to handle the DSI syncs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
We have a bunch of dsi functions that are used to do the basic
configuration for DSI. To simplify things, and to make sure we have all
the necessary information, create a single dsi config function, which
does the basic configuration.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The DISPC channel used for each output is currently passed in panel
platform data from the board files.
To simplify this, and to make the panel drivers less dependent on OMAP,
this patch changes omapdss to resolve the channel independently. The
channel is resolved based on the OMAP version and, in case of DSI, the
DSI module id. This resolved channel is stored into a new field in
output, dispc_channel.
The few places where dssdev->channel was used are changed to use
output->recommended_channel. After this patch, dssdev->channel is
obsolete.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Add name field to omapdss's outputs so that in the following patches
panels refer to the output by their name. The name also helps debugging.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
struct omap_dss_device contains HDMI clock divisors. The idea is that the
board file can pass precalculated divisors to the display driver.
However, these divsors are no longer needed, as the omapdss driver can
calculate the divisors during runtime.
This patch removes the divisors from omap_dss_device, and their uses
from the hdmi driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
struct omap_dss_device contains DSS clock divisors. The idea is that the
board file can pass precalculated divisors to the display driver.
However, these divsors are no longer needed, as the omapdss driver can
calculate the divisors during runtime.
This patch removes the divisors from omap_dss_device, and their uses
from the dsi driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Forthcoming panel patches will change the panel drivers to use platform
data to pass panel's gpios to the panel driver. This patch adds the
required fields and platform data structs to the omap-panel-data.h file,
so that the board files can be changed independently of the panel driver
changes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Structs for platform data of omapdss panels are found in headers in the
'include/video/' path. Board files populate these structs with platform
specific values, and the panel driver uses these to configure the panel.
Currently, each panel has it's own header in the above path. Move all the
omapdss panel platform data structs to a single header omap-panel-data.h.
This is useful because:
- All other omapdss panel drivers will be modified to use platform data. This
would lead to a lot of panel headers usable only by omapdss. A lot of these
platform data structs are trivial, and don't really need a separate header.
- Platform data would be eventually removed, and platform information would be
passed via device tree. Therefore, omapdss panel platform data structs are
temporary, and will be easier to remove if they are all in the same header.
- All board files will have to include the same header to configure a panel's
platform data, that makes the board files more consistent.
Signed-off-by: Archit Taneja <archit@ti.com>
We currently have videomode_from_timing(), which takes one
display_timing entry from display_timings.
To make it easier to use display_timing without display_timings, this
patch renames videomode_from_timing() to videomode_from_timings(), and
adds a new videomode_from_timing() which just converts a given
display_timing to videomode.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Add platform device-id table in order to identify the controller and
determine its configuration.
The currently used configuration parameters are:
have_alt_pixclock
- SOC uses an alternate pixel-clock calculation formula (at91sam9g45
non-ES)
have_hozval
- SOC has a HOZVAL field in LCDFRMCFG which is used to determine the
linesize for STN displays (at91sam9261, at921sam9g10 and at32ap)
have_intensity_bit
- SOC uses IBGR:555 rather than BGR:565 16-bit pixel layout
(at91sam9261, at91sam9263 and at91sam9rl)
This allows us to remove all the remaining uses of cpu_is macros from
the driver.
Tested on at91sam9263 and at91sam9g45, compile-tested for other
AT91-SOCs, and untested for AVR32.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix regression introduced by commit 787f9fd232 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather than
BGR:565.
The above commit removes the RGB:555-wiring hack by
removing the no longer used ATMEL_LCDC_WIRING_RGB555 define.
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Fix regression introduced by commit 787f9fd232 ("atmel_lcdfb: support
16bit BGR:565 mode, remove unsupported 15bit modes") which broke 16-bpp
modes for older SOCs which use IBGR:555 (msb is intensity) rather
than BGR:565.
Use SOC-type to determine the pixel layout.
Tested on at91sam9263 and at91sam9g45.
Cc: <stable@vger.kernel.org>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Display timing's fields have minimum, typical and maximum values. These
can be accessed by using timing_entry_index enum, and
display_timing_get_value() function.
There's no real need for this extra complexity. The values can be
accessed more easily by just using the min/typ/max fields.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Instead of having plain defines for the videomode's flags, add an enum
for the flags. This makes the flags clearer to use, as the enum tells
which values can be used with the flags field.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Both videomode and display_timing contain flags describing the modes.
These are stored in dmt_flags and data_flags. There's no need to
separate these flags, and having separate fields just makes the flags
more difficult to use.
This patch combines the fields and renames VESA_DMT_* flags to
DISPLAY_FLAGS_*.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JMlx
-----END PGP SIGNATURE-----
Merge tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers
Pull fbdev UAPI disintegration from David Howells:
"You'll be glad to here that the end is nigh for the UAPI patches.
Only the fbdev/framebuffer piece remains now that the SCSI stuff has
gone in.
Here are the UAPI disintegration bits for the fbdev drivers. It
appears that Florian hasn't had time to deal with my patch, but back
in December he did say he didn't mind if I pushed it forward."
Yay. No more uapi movement. And hopefully no more big header file
cleanups coming up either, it just tends to be very painful.
* tag 'disintegrate-fbdev-20121220' of git://git.infradead.org/users/dhowells/linux-headers:
UAPI: (Scripted) Disintegrate include/video
Pull drm merge from Dave Airlie:
"Highlights:
- TI LCD controller KMS driver
- TI OMAP KMS driver merged from staging
- drop gma500 stub driver
- the fbcon locking fixes
- the vgacon dirty like zebra fix.
- open firmware videomode and hdmi common code helpers
- major locking rework for kms object handling - pageflip/cursor
won't block on polling anymore!
- fbcon helper and prime helper cleanups
- i915: all over the map, haswell power well enhancements, valleyview
macro horrors cleaned up, killing lots of legacy GTT code,
- radeon: CS ioctl unification, deprecated UMS support, gpu reset
rework, VM fixes
- nouveau: reworked thermal code, external dp/tmds encoder support
(anx9805), fences sleep instead of polling,
- exynos: all over the driver fixes."
Lovely conflict in radeon/evergreen_cs.c between commit de0babd60d
("drm/radeon: enforce use of radeon_get_ib_value when reading user cmd")
and the new changes that modified that evergreen_dma_cs_parse()
function.
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (508 commits)
drm/tilcdc: only build on arm
drm/i915: Revert hdmi HDP pin checks
drm/tegra: Add list of framebuffers to debugfs
drm/tegra: Fix color expansion
drm/tegra: Split DC_CMD_STATE_CONTROL register write
drm/tegra: Implement page-flipping support
drm/tegra: Implement VBLANK support
drm/tegra: Implement .mode_set_base()
drm/tegra: Add plane support
drm/tegra: Remove bogus tegra_framebuffer structure
drm: Add consistency check for page-flipping
drm/radeon: Use generic HDMI infoframe helpers
drm/tegra: Use generic HDMI infoframe helpers
drm: Add EDID helper documentation
drm: Add HDMI infoframe helpers
video: Add generic HDMI infoframe helpers
drm: Add some missing forward declarations
drm: Move mode tables to drm_edid.c
drm: Remove duplicate drm_mode_cea_vic()
gma500: Fix n, m1 and m2 clock limits for sdvo and lvds
...
The correct value for VIDCON1_VSTATUS_FRONTPORCH is 3, not 0.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
