This patch adds the necessary functions to compute and check the HMAC signature
of an SR-enabled packet. Two HMAC algorithms are supported: hmac(sha1) and
hmac(sha256).
In order to avoid dynamic memory allocation for each HMAC computation,
a per-cpu ring buffer is allocated for this purpose.
A new per-interface sysctl called seg6_require_hmac is added, allowing a
user-defined policy for processing HMAC-signed SR-enabled packets.
A value of -1 means that the HMAC field will always be ignored.
A value of 0 means that if an HMAC field is present, its validity will
be enforced (the packet is dropped is the signature is incorrect).
Finally, a value of 1 means that any SR-enabled packet that does not
contain an HMAC signature or whose signature is incorrect will be dropped.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch creates a new type of interfaceless lightweight tunnel (SEG6),
enabling the encapsulation and injection of SRH within locally emitted
packets and forwarded packets.
>From a configuration viewpoint, a seg6 tunnel would be configured as follows:
ip -6 ro ad fc00::1/128 encap seg6 mode encap segs fc42::1,fc42::2,fc42::3 dev eth0
Any packet whose destination address is fc00::1 would thus be encapsulated
within an outer IPv6 header containing the SRH with three segments, and would
actually be routed to the first segment of the list. If `mode inline' was
specified instead of `mode encap', then the SRH would be directly inserted
after the IPv6 header without outer encapsulation.
The inline mode is only available if CONFIG_IPV6_SEG6_INLINE is enabled. This
feature was made configurable because direct header insertion may break
several mechanisms such as PMTUD or IPSec AH.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary hooks and structures to provide support
for SR-IPv6 control plane, essentially the Generic Netlink commands
that will be used for userspace control over the Segment Routing
kernel structures.
The genetlink commands provide control over two different structures:
tunnel source and HMAC data. The tunnel source is the source address
that will be used by default when encapsulating packets into an
outer IPv6 header + SRH. If the tunnel source is set to :: then an
address of the outgoing interface will be selected as the source.
The HMAC commands currently just return ENOTSUPP and will be implemented
in a future patch.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement minimal support for processing of SR-enabled packets
as described in
https://tools.ietf.org/html/draft-ietf-6man-segment-routing-header-02.
This patch implements the following operations:
- Intermediate segment endpoint: incrementation of active segment and rerouting.
- Egress for SR-encapsulated packets: decapsulation of outer IPv6 header + SRH
and routing of inner packet.
- Cleanup flag support for SR-inlined packets: removal of SRH if we are the
penultimate segment endpoint.
A per-interface sysctl seg6_enabled is provided, to accept/deny SR-enabled
packets. Default is deny.
This patch does not provide support for HMAC-signed packets.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dst port parameter to __ip_tun_set_dst and __ipv6_tun_set_dst
utility functions.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current IP tunneling classification supports only IP addresses and key.
Enhance UDP based IP tunneling classification parameters by adding UDP
src and dst port.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New encapsulation keys were added to the flower classifier, which allow
classification according to outer (encapsulation) headers attributes
such as key and IP addresses.
In order to expose those attributes outside flower, add
corresponding enums in the flow dissector.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Needed for drivers to pick the relevant action when offloading tunnel
key act.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default TX queue length of Ethernet devices have been a magic
constant of 1000, ever since the initial git import.
Looking back in historical trees[1][2] the value used to be 100,
with the same comment "Ethernet wants good queues". The commit[3]
that changed this from 100 to 1000 didn't describe why, but from
conversations with Robert Olsson it seems that it was changed
when Ethernet devices went from 100Mbit/s to 1Gbit/s, because the
link speed increased x10 the queue size were also adjusted. This
value later caused much heartache for the bufferbloat community.
This patch merely moves the value into a defined constant.
[1] https://git.kernel.org/cgit/linux/kernel/git/davem/netdev-vger-cvs.git/
[2] https://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/
[3] https://git.kernel.org/tglx/history/c/98921832c232
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new argument is added to __skb_recv_datagram to provide
an explicit skb destructor, invoked under the receive queue
lock.
The UDP protocol uses such argument to perform memory
reclaiming on dequeue, so that the UDP protocol does not
set anymore skb->desctructor.
Instead explicit memory reclaiming is performed at close() time and
when skbs are removed from the receive queue.
The in kernel UDP protocol users now need to call a
skb_recv_udp() variant instead of skb_recv_datagram() to
properly perform memory accounting on dequeue.
Overall, this allows acquiring only once the receive queue
lock on dequeue.
Tested using pktgen with random src port, 64 bytes packet,
wire-speed on a 10G link as sender and udp_sink as the receiver,
using an l4 tuple rxhash to stress the contention, and one or more
udp_sink instances with reuseport.
nr sinks vanilla patched
1 440 560
3 2150 2300
6 3650 3800
9 4450 4600
12 6250 6450
v1 -> v2:
- do rmem and allocated memory scheduling under the receive lock
- do bulk scheduling in first_packet_length() and in udp_destruct_sock()
- avoid the typdef for the dequeue callback
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that we can use it even after orphaining the skbuff.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use the UID in routing lookups made by protocol connect() and
sendmsg() functions.
- Make sure that routing lookups triggered by incoming packets
(e.g., Path MTU discovery) take the UID of the socket into
account.
- For packets not associated with a userspace socket, (e.g., ping
replies) use UID 0 inside the user namespace corresponding to
the network namespace the socket belongs to. This allows
all namespaces to apply routing and iptables rules to
kernel-originated traffic in that namespaces by matching UID 0.
This is better than using the UID of the kernel socket that is
sending the traffic, because the UID of kernel sockets created
at namespace creation time (e.g., the per-processor ICMP and
TCP sockets) is the UID of the user that created the socket,
which might not be mapped in the namespace.
Tested: compiles allnoconfig, allyesconfig, allmodconfig
Tested: https://android-review.googlesource.com/253302
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Define a new FIB rule attributes, FRA_UID_RANGE, to describe a
range of UIDs.
- Define a RTA_UID attribute for per-UID route lookups and dumps.
- Support passing these attributes to and from userspace via
rtnetlink. The value INVALID_UID indicates no UID was
specified.
- Add a UID field to the flow structures.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocol sockets (struct sock) don't have UIDs, but most of the
time, they map 1:1 to userspace sockets (struct socket) which do.
Various operations such as the iptables xt_owner match need
access to the "UID of a socket", and do so by following the
backpointer to the struct socket. This involves taking
sk_callback_lock and doesn't work when there is no socket
because userspace has already called close().
Simplify this by adding a sk_uid field to struct sock whose value
matches the UID of the corresponding struct socket. The semantics
are as follows:
1. Whenever sk_socket is non-null: sk_uid is the same as the UID
in sk_socket, i.e., matches the return value of sock_i_uid.
Specifically, the UID is set when userspace calls socket(),
fchown(), or accept().
2. When sk_socket is NULL, sk_uid is defined as follows:
- For a socket that no longer has a sk_socket because
userspace has called close(): the previous UID.
- For a cloned socket (e.g., an incoming connection that is
established but on which userspace has not yet called
accept): the UID of the socket it was cloned from.
- For a socket that has never had an sk_socket: UID 0 inside
the user namespace corresponding to the network namespace
the socket belongs to.
Kernel sockets created by sock_create_kern are a special case
of #1 and sk_uid is the user that created them. For kernel
sockets created at network namespace creation time, such as the
per-processor ICMP and TCP sockets, this is the user that created
the network namespace.
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The IP stack records the largest fragment of a reassembled packet
in IPCB(skb)->frag_max_size. When reading a datagram or raw packet
that arrived fragmented, expose the value to allow applications to
estimate receive path MTU.
Tested:
Sent data over a veth pair of which the source has a small mtu.
Sent data using netcat, received using a dedicated process.
Verified that the cmsg IP_RECVFRAGSIZE is returned only when
data arrives fragmented, and in that cases matches the veth mtu.
ip link add veth0 type veth peer name veth1
ip netns add from
ip netns add to
ip link set dev veth1 netns to
ip netns exec to ip addr add dev veth1 192.168.10.1/24
ip netns exec to ip link set dev veth1 up
ip link set dev veth0 netns from
ip netns exec from ip addr add dev veth0 192.168.10.2/24
ip netns exec from ip link set dev veth0 up
ip netns exec from ip link set dev veth0 mtu 1300
ip netns exec from ethtool -K veth0 ufo off
dd if=/dev/zero bs=1 count=1400 2>/dev/null > payload
ip netns exec to ./recv_cmsg_recvfragsize -4 -u -p 6000 &
ip netns exec from nc -q 1 -u 192.168.10.1 6000 < payload
using github.com/wdebruij/kerneltools/blob/master/tests/recvfragsize.c
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. This includes better integration with the routing subsystem for
nf_tables, explicit notrack support and smaller updates. More
specifically, they are:
1) Add fib lookup expression for nf_tables, from Florian Westphal. This
new expression provides a native replacement for iptables addrtype
and rp_filter matches. This is more flexible though, since we can
populate the kernel flowi representation to inquire fib to
accomodate new usecases, such as RTBH through skb mark.
2) Introduce rt expression for nf_tables, from Anders K. Pedersen. This
new expression allow you to access skbuff route metadata, more
specifically nexthop and classid fields.
3) Add notrack support for nf_tables, to skip conntracking, requested by
many users already.
4) Add boilerplate code to allow to use nf_log infrastructure from
nf_tables ingress.
5) Allow to mangle pkttype from nf_tables prerouting chain, to emulate
the xtables cluster match, from Liping Zhang.
6) Move socket lookup code into generic nf_socket_* infrastructure so
we can provide a native replacement for the xtables socket match.
7) Make sure nfnetlink_queue data that is updated on every packets is
placed in a different cache from read-only data, from Florian Westphal.
8) Handle NF_STOLEN from nf_tables core, also from Florian Westphal.
9) Start round robin number generation in nft_numgen from zero,
instead of n-1, for consistency with xtables statistics match,
patch from Liping Zhang.
10) Set GFP_NOWARN flag in skbuff netlink allocations in nfnetlink_log,
given we retry with a smaller allocation on failure, from Calvin Owens.
11) Cleanup xt_multiport to use switch(), from Gao feng.
12) Remove superfluous check in nft_immediate and nft_cmp, from
Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Move layer 2 packet logging into nf_log_l2packet() that resides in
nf_log_common.c, so this can be shared by both bridge and netdev
families.
This patch adds the boiler plate code to register the netdev logging
family.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Add FIB expression, supported for ipv4, ipv6 and inet family (the latter
just dispatches to ipv4 or ipv6 one based on nfproto).
Currently supports fetching output interface index/name and the
rtm_type associated with an address.
This can be used for adding path filtering. rtm_type is useful
to e.g. enforce a strong-end host model where packets
are only accepted if daddr is configured on the interface the
packet arrived on.
The fib expression is a native nftables alternative to the
xtables addrtype and rp_filter matches.
FIB result order for oif/oifname retrieval is as follows:
- if packet is local (skb has rtable, RTF_LOCAL set, this
will also catch looped-back multicast packets), set oif to
the loopback interface.
- if fib lookup returns an error, or result points to local,
store zero result. This means '--local' option of -m rpfilter
is not supported. It is possible to use 'fib type local' or add
explicit saddr/daddr matching rules to create exceptions if this
is really needed.
- store result in the destination register.
In case of multiple routes, search set for desired oif in case
strict matching is requested.
ipv4 and ipv6 behave fib expressions are supposed to behave the same.
[ I have collapsed Arnd Bergmann's ("netfilter: nf_tables: fib warnings")
http://patchwork.ozlabs.org/patch/688615/
to address fallout from this patch after rebasing nf-next, that was
posted to address compilation warnings. --pablo ]
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Systems with large pages (64KB pages for example) do not always have
huge quantity of memory.
A big SK_MEM_QUANTUM value leads to fewer interactions with the
global counters (like tcp_memory_allocated) but might trigger
memory pressure much faster, giving suboptimal TCP performance
since windows are lowered to ridiculous values.
Note that sysctl_mem units being in pages and in ABI, we also need
to change sk_prot_mem_limits() accordingly.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
When vxlan device is closed vxlan socket is freed. This
operation can race with vxlan-xmit function which
dereferences vxlan socket. Following patch uses RCU
mechanism to avoid this situation.
Signed-off-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* client FILS authentication support in mac80211 (Jouni)
* AP/VLAN multicast improvements (Michael Braun)
* config/advertising support for differing beacon intervals on
multiple virtual interfaces (Purushottam Kushwaha, myself)
* deprecate the old WDS mode for cfg80211-based drivers, the
mode is hardly usable since it doesn't support any "modern"
features like WPA encryption (2003), HT (2009) or VHT (2014),
I'm not even sure WEP (introduced in 1997) could be done.
-----BEGIN PGP SIGNATURE-----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=SjfQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-10-28' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Among various cleanups and improvements, we have the following:
* client FILS authentication support in mac80211 (Jouni)
* AP/VLAN multicast improvements (Michael Braun)
* config/advertising support for differing beacon intervals on
multiple virtual interfaces (Purushottam Kushwaha, myself)
* deprecate the old WDS mode for cfg80211-based drivers, the
mode is hardly usable since it doesn't support any "modern"
features like WPA encryption (2003), HT (2009) or VHT (2014),
I'm not even sure WEP (introduced in 1997) could be done.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
* a fix to process all events while suspending, so any
potential calls into the driver are done before it is
suspended
* small markup fixes for the sphinx documentation conversion
that's coming into the tree via the doc tree
-----BEGIN PGP SIGNATURE-----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=toQY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-10-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two fixes:
* a fix to process all events while suspending, so any
potential calls into the driver are done before it is
suspended
* small markup fixes for the sphinx documentation conversion
that's coming into the tree via the doc tree
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Per listen(fd, backlog) rules, there is really no point accepting a SYN,
sending a SYNACK, and dropping the following ACK packet if accept queue
is full, because application is not draining accept queue fast enough.
This behavior is fooling TCP clients that believe they established a
flow, while there is nothing at server side. They might then send about
10 MSS (if using IW10) that will be dropped anyway while server is under
stress.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrap several common instances of:
kmemdup(nla_data(attr), nla_len(attr), GFP_KERNEL);
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to IPv4, do not consider link state when validating next hops.
Currently, if the link is down default routes can fail to insert:
$ ip -6 ro add vrf blue default via 2100:2::64 dev eth2
RTNETLINK answers: No route to host
With this patch the command succeeds.
Fixes: 8c14586fc3 ("net: ipv6: Use passed in table for nexthop lookups")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt6_add_route_info and rt6_add_dflt_router were updated to pull the FIB
table from the device index, but the corresponding rt6_get_route_info
and rt6_get_dflt_router functions were not leading to the failure to
process RA's:
ICMPv6: RA: ndisc_router_discovery failed to add default route
Fix the 'get' functions by using the table id associated with the
device when applicable.
Also, now that default routes can be added to tables other than the
default table, rt6_purge_dflt_routers needs to be updated as well to
look at all tables. To handle that efficiently, add a flag to the table
denoting if it is has a default route via RA.
Fixes: ca254490c8 ("net: Add VRF support to IPv6 stack")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since generic netlink family IDs are small integers, allocated
densely, IDR is an ideal match for lookups. Replace the existing
hand-written hash-table with IDR for allocation and lookup.
This lets the families only be written to once, during register,
since the list_head can be removed and removal of a family won't
cause any writes.
It also slightly reduces the code size (by about 1.3k on x86-64).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of providing macros/inline functions to initialize
the families, make all users initialize them statically and
get rid of the macros.
This reduces the kernel code size by about 1.6k on x86-64
(with allyesconfig).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static family IDs have never really been used, the only
use case was the workaround I introduced for those users
that assumed their family ID was also their multicast
group ID.
Additionally, because static family IDs would never be
reserved by the generic netlink code, using a relatively
low ID would only work for built-in families that can be
registered immediately after generic netlink is started,
which is basically only the control family (apart from
the workaround code, which I also had to add code for so
it would reserve those IDs)
Thus, anything other than GENL_ID_GENERATE is flawed and
luckily not used except in the cases I mentioned. Move
those workarounds into a few lines of code, and then get
rid of GENL_ID_GENERATE entirely, making it more robust.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helper function allows family implementations to access
their family's attrbuf. This gets rid of the attrbuf usage
in families, and also adds locking validation, since it's not
valid to use the attrbuf with parallel_ops or outside of the
dumpit callback.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The user may want to use only some bits of the skb mark in
his skbedit rules because the remaining part might be used by
something else.
Introduce the "mask" parameter to the skbedit actor in order
to implement such functionality.
When the mask is specified, only those bits selected by the
latter are altered really changed by the actor, while the
rest is left untouched.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functionality to update the connection parameters when in connected
state, so that driver/firmware uses the updated parameters for
subsequent roaming. This is for drivers that support internal BSS
selection and roaming. The new command does not change the current
association state, i.e., it can be used to update IE contents for future
(re)associations without causing an immediate disassociation or
reassociation with the current BSS.
This commit implements the required functionality for updating IEs for
(Re)Association Request frame only. Other parameters can be added in
future when required.
Signed-off-by: vamsi krishna <vamsin@qti.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the ability to configure if an AP (and associated VLANs) will
do multicast-to-unicast conversion for ARP, IPv4 and IPv6 frames
(possibly within 802.1Q). If enabled, such frames are to be sent
to each station separately, with the DA replaced by their own MAC
address rather than the group address.
Note that this may break certain expectations of the receiver,
such as the ability to drop unicast IP packets received within
multicast L2 frames, or the ability to not send ICMP destination
unreachable messages for packets received in L2 multicast (which
is required, but the receiver can't tell the difference if this
new option is enabled.)
This also doesn't implement the 802.11 DMS (directed multicast
service).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[fix disabling, add better documentation & commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The new nl80211 attributes can be used to provide KEK and nonces to
allow the driver to encrypt and decrypt FILS (Re)Association
Request/Response frames in station mode.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Define the Element IDs and Element ID Extensions from IEEE
P802.11ai/D11.0. In addition, add a new cfg80211_find_ext_ie() wrapper
to make it easier to find information elements that used the Element ID
Extension field.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds defines and nl80211 extensions to allow FILS Authentication to
be implemented similarly to SAE. FILS does not need the special rules
for the Authentication transaction number and Status code fields, but it
does need to add non-IE fields. The previously used
NL80211_ATTR_SAE_DATA can be reused for this to avoid having to
duplicate that implementation. Rename that attribute to more generic
NL80211_ATTR_AUTH_DATA (with backwards compatibility define for
NL80211_SAE_DATA).
Also document the special rules related to the Authentication
transaction number and Status code fiels.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the pointless checking against interface combinations in
the initial basic beacon interval validation, that currently isn't
taking into account radar detection or channels properly. Instead,
just validate the basic range there, and then delay real checking
to the interface combination validation that drivers must do.
This means that drivers wanting to use the beacon_int_min_gcd will
now have to pass the new_beacon_int when validating the AP/mesh
start.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a helper using wdev to check if interface is running. This
deals with both non-netdev and netdev interfaces. In struct
wireless_dev replace 'p2p_started' and 'nan_started' by
'is_running' as those are mutually exclusive anyway, and unify
all the code to use wdev_running().
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
First bug was added in commit ad6f939ab1 ("ip: Add offset parameter to
ip_cmsg_recv") : Tom missed that ipv4 udp messages could be received on
AF_INET6 socket. ip_cmsg_recv(msg, skb) should have been replaced by
ip_cmsg_recv_offset(msg, skb, sizeof(struct udphdr));
Then commit e6afc8ace6 ("udp: remove headers from UDP packets before
queueing") forgot to adjust the offsets now UDP headers are pulled
before skb are put in receive queue.
Fixes: ad6f939ab1 ("ip: Add offset parameter to ip_cmsg_recv")
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skbuff and sock structure both had missing parameter annotation
values.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In criu we are actively using diag interface to collect sockets
present in the system when dumping applications. And while for
unix, tcp, udp[lite], packet, netlink it works as expected,
the raw sockets do not have. Thus add it.
v2:
- add missing sock_put calls in raw_diag_dump_one (by eric.dumazet@)
- implement @destroy for diag requests (by dsa@)
v3:
- add export of raw_abort for IPv6 (by dsa@)
- pass net-admin flag into inet_sk_diag_fill due to
changes in net-next branch (by dsa@)
v4:
- use @pad in struct inet_diag_req_v2 for raw socket
protocol specification: raw module carries sockets
which may have custom protocol passed from socket()
syscall and sole @sdiag_protocol is not enough to
match underlied ones
- start reporting protocol specifed in socket() call
when sockets are raw ones for the same reason: user
space tools like ss may parse this attribute and use
it for socket matching
v5 (by eric.dumazet@):
- use sock_hold in raw_sock_get instead of atomic_inc,
we're holding (raw_v4_hashinfo|raw_v6_hashinfo)->lock
when looking up so counter won't be zero here.
v6:
- use sdiag_raw_protocol() helper which will access @pad
structure used for raw sockets protocol specification:
we can't simply rename this member without breaking uapi
v7:
- sine sdiag_raw_protocol() helper is not suitable for
uapi lets rather make an alias structure with proper
names. __check_inet_diag_req_raw helper will catch
if any of structure unintentionally changed.
CC: David S. Miller <davem@davemloft.net>
CC: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Ahern <dsa@cumulusnetworks.com>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Andrey Vagin <avagin@openvz.org>
CC: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The field is initialized by ILA and MPLS but never used. Remove it.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid using the generic helpers.
Use the receive queue spin lock to protect the memory
accounting operation, both on enqueue and on dequeue.
On dequeue perform partial memory reclaiming, trying to
leave a quantum of forward allocated memory.
On enqueue use a custom helper, to allow some optimizations:
- use a plain spin_lock() variant instead of the slightly
costly spin_lock_irqsave(),
- avoid dst_force check, since the calling code has already
dropped the skb dst
- avoid orphaning the skb, since skb_steal_sock() already did
the work for us
The above needs custom memory reclaiming on shutdown, provided
by the udp_destruct_sock().
v5 -> v6:
- don't orphan the skb on enqueue
v4 -> v5:
- replace the mem_lock with the receive queue spin lock
- ensure that the bh is always allowed to enqueue at least
a skb, even if sk_rcvbuf is exceeded
v3 -> v4:
- reworked memory accunting, simplifying the schema
- provide an helper for both memory scheduling and enqueuing
v1 -> v2:
- use a udp specific destrctor to perform memory reclaiming
- remove a couple of helpers, unneeded after the above cleanup
- do not reclaim memory on dequeue if not under memory
pressure
- reworked the fwd accounting schema to avoid potential
integer overflow
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Basic sock operations that udp code can use with its own
memory accounting schema. No functional change is introduced
in the existing APIs.
v4 -> v5:
- avoid whitespace changes
v2 -> v4:
- avoid exporting __sock_enqueue_skb
v1 -> v2:
- avoid export sock_rmem_free
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Baozeng reported this deadlock case:
CPU0 CPU1
---- ----
lock([ 165.136033] sk_lock-AF_INET6);
lock([ 165.136033] rtnl_mutex);
lock([ 165.136033] sk_lock-AF_INET6);
lock([ 165.136033] rtnl_mutex);
Similar to commit 87e9f03159
("ipv4: fix a potential deadlock in mcast getsockopt() path")
this is due to we still have a case, ipv6_sock_mc_close(),
where we acquire sk_lock before rtnl_lock. Close this deadlock
with the similar solution, that is always acquire rtnl lock first.
Fixes: baf606d9c9 ("ipv4,ipv6: grab rtnl before locking the socket")
Reported-by: Baozeng Ding <sploving1@gmail.com>
Tested-by: Baozeng Ding <sploving1@gmail.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Baozeng Ding reported KASAN traces showing uses after free in
udp_lib_get_port() and other related UDP functions.
A CONFIG_DEBUG_PAGEALLOC=y kernel would eventually crash.
I could write a reproducer with two threads doing :
static int sock_fd;
static void *thr1(void *arg)
{
for (;;) {
connect(sock_fd, (const struct sockaddr *)arg,
sizeof(struct sockaddr_in));
}
}
static void *thr2(void *arg)
{
struct sockaddr_in unspec;
for (;;) {
memset(&unspec, 0, sizeof(unspec));
connect(sock_fd, (const struct sockaddr *)&unspec,
sizeof(unspec));
}
}
Problem is that udp_disconnect() could run without holding socket lock,
and this was causing list corruptions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Baozeng Ding <sploving1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
