Fix to return a negative error code from the error handling
case instead of 0.
Fixes: 837052d0cc ('net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling')
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check if the device get enough bandwidth from the entire PCI chain to satisfy
its capabilities. This patch determines the PCIe device's bandwidth capabilities
by reading its PCIe Link Capabilities registers and then call the
pcie_get_minimum_link function to ensure that the adapter is hooked into a slot
which is capable of providing the necessary bandwidth capabilities.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hwtstamp_config matches what is currently set for the device then
simply return. Without this change any program that tries to enable
hardware timestamps will cause the link to cycle even if hardware
timstamps were already enabled.
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Acked-By: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds a PHC to the mlx4_en driver. We use reader/writer spinlocks to
protect the timecounter since every packet received needs to call
timecounter_cycle2time() when timestamping is enabled. This can become
a performance bottleneck with RSS and multiple receive queues if normal
spinlocks are used.
This driver has been tested with both Documentation/ptp/testptp and the
linuxptp project (http://linuxptp.sourceforge.net/) on a Mellanox
ConnectX-3 card.
Signed-off-by: Shawn Bohrer <sbohrer@rgmadvisors.com>
Acked-By: Hadar Hen Zion <hadarh@mellanox.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use possibly more efficient ether_addr_equal
to instead of memcmp.
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the device tunneling offloads mode is vxlan do the following
- call SET_PORT with the relevant setting
- add DMFS steering vxlan rule for the device self and multicast mac addresses
of the form: {<ETH, outer-mac> <VXLAN, ANY vnid> <ETH, ANY mac>} --> RSS QP
- set relevant QPC fields in RSS context and RX ring QPs
- in TX flow, set WQE fields to generate HW checksum, and handle gso skbs
which are marked for encapsulation such that the HW will segment them properly.
- in RX flow, read HW offloaded checksum for encapsulated packets from the CQE
- advertize hw_enc_features and NETIF_F_GSO_UDP_TUNNEL to the networking stack
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the low-level device commands and definitions used for TCP/IP HW offloads
of tunneled/vxlan traffic which are supported by the ConnectX3-pro NIC.
This is done through the following elements:
- read tunneling device caps in QUERY_DEV_CAP
- add helper function to do SET_PORT for tunneling
- add DMFS VXLAN steering rule definitions
- add CQE and WQE checksum offload field definitions
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to validate port number at mlx4_promisc_qp() before use.
Since port number is extracted from gid, as a cooked or corrupted gid
could lead to a crash.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add NAPI for TX side,
implement its support and provide NAPI callback.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MLX4_DEV_EVENT_SLAVE_INIT and MLX4_DEV_EVENT_SLAVE_SHUTDOWN
events used by Hypervisor to inform the PPF IB driver that
IB para-virtualization must be initialized/destroyed for a slave.
If this event is catched by ETH VF annoying but harmless error message
is printed into dmesg. Remove dmesg prints for these events.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To achieve out of the box performance default is to use 64 byte CQE/EQE.
In tests that we conduct in our labs, we achieved a performance
improvement of twice the message rate. For older VF/libmlx4 support,
enable_64b_cqe_eqe must be set to 0 (disabled).
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only TX rings of User Piority 0 are mapped.
TX rings of other UP's are using UP 0 mapping.
XPS is not in use when num_tc is set.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the port GUID read from the firmware to identify the physical port.
This port identifier is available via ndo_get_phys_port_id for both PF
and VF net-devices.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the infrastructure needed to support ndo_get_phys_port_id which
allows users to identify to which physical port a net-device is connected
to by reading a unique port id.
This will work for VFs and PFs.
The driver uses a new device capability - phys_port_id, The PF driver
reads the port phys_port_id from Firmware and stores it. The VF driver
reads the port phys_port_id from the PF using QUERY_FUNC_CAP command.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set nic_info field in QUERY_FUNC_CAP, which designates
supplementary NIC information is provided by the hypervisor.
When set, the following fields are valid: nic_num_rings,
nic_indirection_tbl_sz, cur_mac and phys_port_id.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct names for QUERY_FUNC_CAP fields: flags0 and flags1.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All mailboxes are already zeroed by commit:
571b8b9 net/mlx4_core: Initialize all mailbox buffers to zero before use
Remove explicit zero set for force mac and force vlan fields in
mlx4_QUERY_FUNC_CAP_wrapper
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should call skb_set_hash to set the hash and its type
in an skbuff.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f4ec9e9 "mlx4_core: Change bitmap allocator to work in round-robin fashion"
introduced round-robin allocation (via bitmap) for all resources which allocate
via a bitmap.
Round robin allocation is desirable for mcgs, counters, pd's, UARs, and xrcds.
These are simply numbers, with no involvement of ICM memory mapping.
Round robin is required for QPs, since we had a problem with immediate
reuse of a 24-bit QP number (commit f4ec9e9).
However, for other resources which use the bitmap allocator and involve
mapping ICM memory -- MPTs, CQs, SRQs -- round-robin is not desirable.
What happens in these cases is the following:
ICM memory is allocated and mapped in chunks of 256K.
Since the resource allocation index goes up monotonically, the allocator
will eventually require mapping a new chunk. Now, chunks are also unmapped
when their reference count goes back to zero. Thus, if a single app is
running and starts/exits frequently we will have the following situation:
When the app starts, a new chunk must be allocated and mapped.
When the app exits, the chunk reference count goes back to zero, and the
chunk is unmapped and freed. Therefore, the app must pay the cost of allocation
and mapping of ICM memory each time it runs (although the price is paid only when
allocating the initial entry in the new chunk).
For apps which allocate MPTs/SRQs/CQs and which operate as described above,
this presented a performance problem.
We therefore roll back the round-robin allocator modification for MPTs, CQs, SRQs.
Reported-by: Matthew Finlay <matt@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ben Hutchings says:
====================
SIOCGHWTSTAMP ioctl
1. Add the SIOCGHWTSTAMP ioctl and update the timestamping
documentation.
2. Implement SIOCGHWTSTAMP in most drivers that support SIOCSHWTSTAMP.
3. Add a test program to exercise SIOC{G,S}HWTSTAMP.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When driver registration fails, we need to clean up the resources allocated
before. mlx4_core missed destroying the workqueue allocated.
This patch destroys the workqueue when registration fails.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove waiting for TX queues to become empty during selftest.
This check is not necessary for any purpose, and might put
the driver into an infinite loop.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=xxC+
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma updates from Roland Dreier:
- Re-enable flow steering verbs with new improved userspace ABI
- Fixes for slow connection due to GID lookup scalability
- IPoIB fixes
- Many fixes to HW drivers including mlx4, mlx5, ocrdma and qib
- Further improvements to SRP error handling
- Add new transport type for Cisco usNIC
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (66 commits)
IB/core: Re-enable create_flow/destroy_flow uverbs
IB/core: extended command: an improved infrastructure for uverbs commands
IB/core: Remove ib_uverbs_flow_spec structure from userspace
IB/core: Use a common header for uverbs flow_specs
IB/core: Make uverbs flow structure use names like verbs ones
IB/core: Rename 'flow' structs to match other uverbs structs
IB/core: clarify overflow/underflow checks on ib_create/destroy_flow
IB/ucma: Convert use of typedef ctl_table to struct ctl_table
IB/cm: Convert to using idr_alloc_cyclic()
IB/mlx5: Fix page shift in create CQ for userspace
IB/mlx4: Fix device max capabilities check
IB/mlx5: Fix list_del of empty list
IB/mlx5: Remove dead code
IB/core: Encorce MR access rights rules on kernel consumers
IB/mlx4: Fix endless loop in resize CQ
RDMA/cma: Remove unused argument and minor dead code
RDMA/ucma: Discard events for IDs not yet claimed by user space
IB/core: Add Cisco usNIC rdma node and transport types
RDMA/nes: Remove self-assignment from nes_query_qp()
IB/srp: Report receive errors correctly
...
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
For archs with pages size of 4K, when the chunk is freed, fwp is not in the
list so avoid attempting to delete it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
The Connect-IB adapter has an inherent page size which equals 4K.
Define an new enum that equals the page shift and use it instead of
using the value 12 throughout the code.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Change optimal_reclaimed_pages() to increase the output size of each
reclaim pages command. This change reduces significantly the amount of
reclaim pages commands issued to FW when the driver is unloaded which
reduces the overall driver unload time.
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Firmware spec requires reserved fields to be cleared when calling
set_hca_cap. Current code queries and copy to the set area, possibly
resulting in reserved bits not cleared. This patch copies only
writable fields to the set area.
Fix also typo - msx => max
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Connect-IB firmware requires 4K pages to be communicated with the
driver. This patch breaks larger pages to 4K units to enable support
for architectures utilizing larger page size, such as PowerPC. This
patch also fixes several places that referred to PAGE_SHIFT instead of
explicit 12 which is the inherent page shift on Connect-IB.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
If DMA mapping fails, the driver cleared the object that holds the
previously DMA mapped pages. Fix this by allocating a new object for
the command that reports back to firmware that pages can't be
supplied.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Use asynchronous commands to execute up to eight concurrent create MR
commands. This is to fill memory caches faster so we keep consuming
from there. Also, increase timeout for shrinking caches to five
minutes.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
For each RX/TX ring and its CQ, allocation is done on a NUMA node that
corresponds to the core that the data structure should operate on.
The assumption is that the core number is reflected by the ring index.
The affected allocations are the ring/CQ data structures,
the TX/RX info and the shared HW/SW buffer.
For TX rings, each core has rings of all UPs.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done to optimize FW/HW access to host memory.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all TX/RX rings and completion queues are part of the
netdev priv structure and are allocated statically. This patch
will change the priv to hold only arrays of pointers and therefore
all TX/RX rings and completetion queues will be allocated
dynamically. This is in preparation for NUMA aware allocations.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow immediate activate of VGT->VST and VST->VGT transitions, without
the need of rebinding in mlx4_master_immediate_activate_vlan_qos().
Also in struct res_qp: add qp parameters (vlan_index,fvl,vlan_cntrol..)
to the saved set, in order to restore when move to VGT.
- Clear at mlx4_RST2INIT_QP_wrapper()
- Save at mlx4_INIT2RTR_QP_wrapper()
- Restore at mlx4_vf_immed_vlan_work_handler()
Update mlx4_vf_immed_vlan_work_handler() to support VGT.
Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To guarantee that all unused fields in all FW commands for both inboxes
and outboxes are zeroed out, initialize the mailbox buffer to all zeroes.
This is especially important for SRIOV comm-channel virtual commands
(such as QUERY_FUNC_CAP), where if new fields are added to support new
features, the driver can depend on older kernels passing zeroes in these
fields.
In addition to zeroing out the mailbox buffer at allocation time, all
(now unnecessary) calls to memset by the callers of
mlx4_alloc_cmd_mailbox() are removed.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modify RFS code to support applying filters for incoming UDP streams.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
timecounter_init() was was called only after first potential
timecounter_read().
Moved mlx4_en_init_timestamp() before mlx4_en_init_netdev()
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements resource quota grant decision when resources are requested,
for the following resources: QPs, CQs, SRQs, MPTs, MTTs, vlans, MACs,
and Counters.
When granting a resource, the quota system increases the allocated-count
for that slave.
When the slave later frees the resource, its allocated-count is reduced.
A spinlock is used to protect the integrity of each resource's free-pool counter.
(One slave may be in the process of being granted a resource while another
slave has crashed, initiating cleanup of that slave's resource quotas).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current kernels, the mlx4 driver running on a VM does not
differentiate between max resource numbers for the HCA and
max quotas -- it simply takes the quota values passed to it
as max-resource values.
However, the driver actually requires the VFs to be aware of
the actual number of resources that the HCA was initialized with,
for QPs, CQs, SRQs and MPTs.
For QPs, CQs and SRQs, the reason is that in completion handling
the driver must know which of the 24 bits are the actual resource
number, and which are "padding" bits.
For MPTs, also, the driver assumes knowledge of the number of MPTs
in the system.
The previous commit fixes the quota logic on the VM for the quota values
passed to it by QUERY_FUNC_CAPS.
For QPs, CQs, SRQs, and MPTs, it takes the max resource numbers
from QUERY_HCA (and not QUERY_FUNC_CAPS). The quotas passed
in QUERY_FUNC_CAPS are used to report max resource number values
in the response to ib_query_device.
However, the Hypervisor driver must consider that VMs
may be running previous kernels, and compatibility must be preserved.
To resolve the incompatibility with previous kernels running on VMs,
we deprecated the quota fields in mlx4_QUERY_FUNC_CAP. In the
deprecated fields, we pass the max-resource values from INIT_HCA
The quota fields are moved to a new location, and the current kernel
driver takes the proper values from that location. There is
also a new flag in dword 0, bit 28 of the mlx4_QUERY_FUNC_CAP mailbox;
if this flag is set, the (VM) driver takes the quota values from the
new location.
VMs running previous kernels will work properly, except that the max resource
numbers reported in ib_query_device for these resources will be
too high. The Hypervisor driver will, however, enforce the quotas
for these VMs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is step #1 for implementing SRIOV resource quotas for VFs.
Quotas are implemented per resource type for VFs and the PF, to prevent
any entity from simply grabbing all the resources for itself and leaving
the other entities unable to obtain such resources.
Resources which are allocated using quotas: QPs, CQs, SRQs, MPTs, MTTs, MAC,
VLAN, and Counters.
The quota system works as follows:
Each entity (VF or PF) is given a max number of a given resource (its quota),
and a guaranteed minimum number for each resource (starvation prevention).
For QPs, CQs, SRQs, MPTs and MTTs:
50% of the available quantity for the resource is divided equally among
the PF and all the active VFs (i.e., the number of VFs in the mlx4_core module
parameter "num_vfs"). This 50% represents the "guaranteed minimum" pool.
The other 50% is the "free pool", allocated on a first-come-first-serve basis.
For each VF/PF, resources are first allocated from its "guaranteed-minimum"
pool. When that pool is exhausted, the driver attempts to allocate from
the resource "free-pool".
The quota (i.e., max) for the VFs and the PF is:
The free-pool amount (50% of the real max) + the guaranteed minimum
For MACs:
Guarantee 2 MACs per VF/PF per port. As a result, since we have only
128 MACs per port, reduce the allowable number of VFs from 64 to 63.
Any remaining MACs are put into a free pool.
For VLANs:
For the PF, the per-port quota is 128 and guarantee is 64
(to allow the PF to register at least a VLAN per VF in VST mode).
For the VFs, the per-port quota is 64 and the guarantee is 0.
We assume that VGT VFs are trusted not to abuse the VLAN resource.
For Counters:
For all functions (PF and VFs), the quota is 128 and the guarantee is 0.
In this patch, we define the needed structures, which are added to the
resource-tracker struct. In addition, we do initialization
for the resource quota, and adjust the query_device response to use quotas
rather than resource maxima.
As part of the implementation, we introduce a new field in
mlx4_dev: quotas. This field holds the resource quotas used
to report maxima to the upper layers (ib_core, via query_device).
The HCA maxima of these values are passed to the VFs (via
QUERY_HCA) so that they may continue to use these in handling
QPs, CQs, SRQs and MPTs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In procedure mlx4_init_mr_table(), slaves should do no processing,
but should return success. This initialization is hypervisor-only.
However, the check for num_mpts being a power-of-2 was performed
before the check to return immediately if the driver is for a slave.
This resulted in spurious failures.
The order of performing the checks is reversed, so that if the
driver is for a slave, no processing is done and success is returned.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In upstream kernels under SRIOV, the vlan register/unregister calls
were NOPs (doing nothing and returning OK). We detect these old
calls from guests (via the comm channel), since previously the
port number in mlx4_register_vlan was passed (improperly) in the
out_param. This has been corrected so that the port number is now
passed in bits 8..15 of the in_modifier field.
For old calls, these bits will be zero, so if the passed port
number is zero, we can still look at the out_param field to see
if it contains a valid port number. If yes, the VM is running
an old driver.
Since for old drivers, the register/unregister_vlan wrappers were
NOPs, we continue this policy -- the reason being that upstream
had an additional bug in eth driver running on guests (where
procedure mlx4_en_vlan_rx_kill_vid() had the following code:
if (!mlx4_find_cached_vlan(mdev->dev, priv->port, vid, &idx))
mlx4_unregister_vlan(mdev->dev, priv->port, idx);
else
en_err(priv, "could not find vid %d in cache\n", vid);
On a VM, mlx4_find_cached_vlan() will always fail, since the
vlan cache is located on the Hypervisor; on guests it is empty.
Therefore, if we allow upstream guests to register vlans, we will
have vlan leakage since the unregister will never be performed.
Leaving vlan reg/unreg for old guest drivers as a NOP is not a
feature regression, since in upstream the register/unregister
vlan wrapper is a NOP.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add resource tracker support for reg/unreg vlans calls done by VFs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of vlan_index created problems unregistering vlans on guests.
In addition, tools delete vlan by tag, not by index, lets follow that.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions mlx4_register_vlan, mlx4_unregister_vlan, mlx4_register_mac,
mlx4_unregister_mac all made illegal use of the out_param in multifunc mode
to pass the port number. The firmware spec specifies that the port number
should be passed in bits 8..15 of the input-modifier field for ALLOC_RES and
FREE_RES (sections 20.15.1 and 20.15.2).
For MAC register/unregister, this patch contains workarounds so that guests
running previous kernels continue to work on a new Hypervisor, and guests
running the new kernel will continue to work on old hypervisors.
Vlan registeration capability is still not operational in multifunction mode,
since the vlan wrapper functions are not implemented in this patch.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reg/unreg vlan code was broken:
1. a wrapped function called another wrapped function, causing a deadlock.
2. unregister_vlan called cmd_box instead of cmd_box_imm, leading to
incorrectly passed parameters.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be.h
drivers/net/netconsole.c
net/bridge/br_private.h
Three mostly trivial conflicts.
The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.
In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".
Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
In function mlx4_master_deactivate_admin_state() __mlx4_unregister_mac was
called using the MAC index. It should be called with the value of the MAC itself.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
