Commit Graph

2897 Commits

Author SHA1 Message Date
Fabio Estevam
4c0657ae43 i2c: imx: Use -ENXIO as error in the NACK case
According to Documentation/i2c/fault-codes the response to a bus NACK
should be -ENXIO, so fix the error code.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-23 22:25:33 +02:00
Jarkko Nikula
dd77f423e5 i2c: i801: Add support for Intel Broxton
This patch adds the SMBUS PCI ID of Intel Broxton.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-23 22:11:58 +02:00
Mika Westerberg
84d7f2ebd7 i2c: i801: Add support for Intel DNV
Intel DNV SoC has the same legacy SMBus host controller than Intel
Sunrisepoint PCH. It also has same iTCO watchdog on the bus.

Add DNV PCI ID to the list of supported devices.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-23 22:10:31 +02:00
Liguo Zhang
09027e08ac i2c: mediatek: add i2c resume support
mt65xx i2c controller initial setting will be cleared after system suspend,
so we should init mt65xx i2c controller again when system resume.

Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-23 21:58:32 +02:00
Gao Pan
1c4b6c3bcf i2c: imx: implement bus recovery
Implement bus recovery methods for i2c-imx so we can recover from
situations where SCL/SDA are stuck low.

Once i2c bus SCL/SDA are stuck low during transfer, config the i2c
pinctrl to gpio mode by calling pinctrl sleep set function, and then
use GPIO to emulate the i2c protocol to send nine dummy clock to recover
i2c device. After recovery, set i2c pinctrl to default group setting.

Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Gao Pan <b54642@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-23 21:55:50 +02:00
Masahiro Yamada
6a62974b66 i2c: uniphier_f: add UniPhier FIFO-builtin I2C driver
Add support for on-chip I2C controller used on newer UniPhier SoCs
such as PH1-Pro4, PH1-Pro5, etc.  This adapter is equipped with
8-depth TX/RX FIFOs.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-23 21:55:46 +02:00
Masahiro Yamada
dd6fd4a327 i2c: uniphier: add UniPhier FIFO-less I2C driver
Add support for on-chip I2C controller used on old UniPhier SoCs
such as PH1-LD4, PH1-sLD8, etc.  This adapter is so simple that
it has no FIFO in it.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-23 21:55:45 +02:00
Ken Xue
3eddad96c4 i2c: designware: reverts "i2c: designware: Add support for AMD I2C controller"
The patch reverts commit a445900c90 (i2c: designware: Add support for
AMD I2C controller). It never worked anyhow because it did not register
a proper clkdev.

Since kernel 4.1 starts to support APD, there is no need to get freq
from id->driver_data for AMD0010. clkdev is supposed to be already
registered in APD.

So, revert old design and make AMD0010 looks like other ones.

Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Signed-off-by: Xiangliang Yu <Xiangliang.Yu@amd.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-23 21:55:44 +02:00
Shaohui Xie
fa721baed6 i2c: imx: add support for Freescale Layerscape platforms
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-23 21:55:24 +02:00
Cyrille Pitchen
6f6ddbb09d i2c: at91: fix write transfers by clearing pending interrupt first
In some cases a NACK interrupt may be pending in the Status Register (SR)
as a result of a previous transfer. However at91_do_twi_transfer() did not
read the SR to clear pending interruptions before starting a new transfer.
Hence a NACK interrupt rose as soon as it was enabled again at the I2C
controller level, resulting in a wrong sequence of operations and strange
patterns of behaviour on the I2C bus, such as a clock stretch followed by
a restart of the transfer.

This first issue occurred with both DMA and PIO write transfers.

Also when a NACK error was detected during a PIO write transfer, the
interrupt handler used to wrongly start a new transfer by writing into the
Transmit Holding Register (THR). Then the I2C slave was likely to reply
with a second NACK.

This second issue is fixed in atmel_twi_interrupt() by handling the TXRDY
status bit only if both the TXCOMP and NACK status bits are cleared.

Tested with a at24 eeprom on sama5d36ek board running a linux-4.1-at91
kernel image. Adapted to linux-next.

Reported-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Tested-by: Peter Rosin <peda@lysator.liu.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Fixes: 93563a6a71 ("i2c: at91: fix a race condition when using the DMA controller")
Cc: stable@vger.kernel.org #4.1
2015-10-22 15:14:41 +02:00
Jarkko Nikula
319d7f05df i2c: designware: Fix build error when !CONFIG_PM_SLEEP
Commit ("i2c: designware: Rename platform driver probe and PM
functions") introduced "'dw_i2c_plat_prepare' undeclared here" and
"'dw_i2c_plat_complete' undeclared here" build errors when
CONFIG_PM_SLEEP is not set.

Fix this by renaming NULL defined dw_i2c_prepare and dw_i2c_complete PM
hooks to dw_i2c_plat_prepare and dw_i2c_plat_complete since this was
obviously missing from the commit.

Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-22 15:14:18 +02:00
Hezi Shahmoon
0729a04977 i2c: mv64xxx: really allow I2C offloading
Commit 00d8689b85 ("i2c: mv64xxx: rework offload support to fix
several problems") completely reworked the offload support, but left a
debugging-related "return false" at the beginning of the
mv64xxx_i2c_can_offload() function. This has the unfortunate consequence
that offloading is in fact never used, which wasn't really the
intention.

This commit fixes that problem by removing the bogus "return false".

Fixes: 00d8689b85 ("i2c: mv64xxx: rework offload support to fix several problems")
Signed-off-by: Hezi Shahmoon <hezi@marvell.com>
[Thomas: reworked commit log and title.]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: <stable@vger.kernel.org>
2015-10-22 14:47:45 +02:00
Luis de Bethencourt
8c5ec4c7ec i2c: stu300: Fix module autoload for OF platform driver
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.

Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 18:15:39 +02:00
Luis de Bethencourt
598cf1611b i2c: rk3x: Fix module autoload for OF platform driver
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.

Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 18:15:03 +02:00
Luis de Bethencourt
93ae965022 i2c: meson: Fix module autoload for OF platform driver
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.

Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 18:14:36 +02:00
Luis de Bethencourt
d695e22a27 i2c: ibm-iic: Fix module autoload for OF platform driver
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.

Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 18:14:01 +02:00
Geert Uytterhoeven
c6f1891323 i2c: rcar: Remove obsolete platform data support
Since commit 4baadb9e05 ("ARM: shmobile: r8a7778: remove obsolete
setup code"), Renesas R-Car SoCs are only supported in generic DT-only
ARM multi-platform builds.  The driver doesn't need to use platform data
anymore, hence remove platform data configuration.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[wsa: removed now unused ret value and cast to proper enum type]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 18:10:25 +02:00
Wolfram Sang
7bb6da5a3d i2c: sh_mobile: add support for r8a7795 (R-Car H3)
Enable the I2C core for this SoC. It is compitable to Gen2 SoCs, so
reuse the settings.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 18:10:20 +02:00
Wolfram Sang
e7db0d34b3 i2c: rcar: add support for r8a7795 (R-Car H3)
Enable the I2C core for this SoC. I add a new type because this version
has new features (e.g. DMA) which will be added somewhen later.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 18:03:07 +02:00
Max Filippov
b299167652 i2c: ocores: support big-endian register layout
This allows using OpenCores I2C controller attached to its host in
native-endian mode with bi-endian CPUs. Example of such system is Xtensa
XTFPGA platform.

Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 17:47:45 +02:00
Manuel Lauss
8a5e3d472e i2c: au1550: relax bus timings a bit
The i2c-au1550 driver has to program various setup and hold times
for the sda/scl signals by hand.  The current values seem to be
working best when the driver is supplied with 50MHz, however on the
DB1300 board 48MHz is the closest we can get to it, and the timings
are a bit too tight for that, leading to the last bit of a transmission
sometimes being swallowed.  This manifests itself in wrong readings
of the ne1619 sensor and inability to configure the wm8731 i2s codec.

With the relaxed timings, both the sensor and the i2s codec can now
be accessed more reliably over a wider range of I2C block input
frequencies.

Verified on DB1200, DB1300 and DB1550 boards.

Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 17:43:13 +02:00
Barry Song
26f590e674 i2c: tegra: drop duplicated code for assigning algo
This code is repeated in probe:
i2c_dev->adapter.algo = &tegra_i2c_algo;

Cc: Donglin Peng <pengdonglin137@163.com>
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 17:38:19 +02:00
Alexander Sverdlin
35780e860f i2c: davinci: Optimize clock generation on Keystone SoC
According to "KeyStone Architecture Inter-IC Control Bus User Guide", fixed
additive part of frequency divisors (referred as "d" in the code and datasheet)
always equals to 6, independent of module clock prescaler.

                         module clock frequency
master clock frequency = ----------------------
                         (ICCL + 6) + (ICCH + 6)

It was not the case with original Davinci IP. Introduce new compatible property
"ti,keystone-i2c", which triggers special handling in the driver.

Without this change Keystone-based systems (having 204.8MHz input clock) choose
prescaler 29 (PSC=28). Using d=5 in this case leads to bus bitrate ~353kHz
instead of requested 400kHz. After correction, assuming d=6 bus rate is ~392kHz.
This gives ~11% transfer rate increase.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Hemanth Guruva Reddy <hemanth.guruva_reddy@nokia.com>
Tested-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 17:05:16 +02:00
Andy Shevchenko
064181b00e i2c: ismt: issue a warning when fail to request MSI
Issue the warning in all error paths when unable to register MSI or its
handler.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 16:51:42 +02:00
Andy Shevchenko
6befa6dd8d i2c: ismt: propagate actual error code
Propagate actual return code when requesting interrupt fails.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 16:51:41 +02:00
Andy Shevchenko
f92d155d3e i2c: ismt: do not duplicate msi_enabled flag
struct pci_dev already has a flag to track if MSI is enabled or not. Use it
directly.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 16:51:40 +02:00
Andy Shevchenko
fb8918b2cf i2c: ismt: PCI core handles power state for us
There is no need to repeat the work that is already done in the PCI driver
core. Remove suspend and resume callbacks.

Note that there is no more calls performed to enable or disable a PCI
device during suspend-resume cycle. Nowadays they seems to be
superfluous. Someone can read more in [1].

[1] https://www.kernel.org/doc/ols/2009/ols2009-pages-319-330.pdf

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 16:51:39 +02:00
Andy Shevchenko
600ca08023 i2c: ismt: improve usage of devres API
pcim_release() will release any requested region. There is no need to duplicate
this effort in the driver.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 16:51:38 +02:00
Andy Shevchenko
6109dbd618 i2c: ismt: mark register space with __iomem
This fixes the code to suppress sparse warnings like:

drivers/i2c/busses/i2c-ismt.c:725:36: warning: incorrect type in argument 2 (different address spaces)
drivers/i2c/busses/i2c-ismt.c:725:36:    expected void volatile [noderef] <asn:2>*addr
drivers/i2c/busses/i2c-ismt.c:725:36:    got void *

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 16:51:37 +02:00
Mika Westerberg
166c2ba398 i2c / ACPI: Rework I2C device scanning
The way we currently scan I2C devices behind an I2C host controller does not
work in cases where the I2C device in question is not declared directly below
the host controller ACPI node.

This is perfectly legal according the ACPI 6.0 specification and some existing
systems are doing this.

To be able to enumerate all devices which are connected to a certain I2C host
controller we need to rework the current I2C scanning routine a bit. Instead of
scanning directly below the host controller we scan the whole ACPI namespace
for present devices with valid I2cSerialBus() connection pointing to the host
controller in question.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Dustin Byford <dustin@cumulusnetworks.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-20 16:51:14 +02:00
Mika Westerberg
56d4b8a24c i2c: designware: Do not use parameters from ACPI on Dell Inspiron 7348
ACPI SSCN/FMCN methods were originally added because then the platform can
provide the most accurate HCNT/LCNT values to the driver. However, this
seems not to be true for Dell Inspiron 7348 where using these causes the
touchpad to fail in boot:

  i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
  i2c_designware INT3433:00: i2c_dw_handle_tx_abort: lost arbitration
  i2c_hid i2c-DLL0675:00: failed to retrieve report from device.
  i2c_designware INT3433:00: controller timed out

The values received from ACPI are (in fast mode):

  HCNT: 72
  LCNT: 160

this translates to following timings (input clock is 100MHz on Broadwell):

  tHIGH: 720 ns (spec min 600 ns)
  tLOW: 1600 ns (spec min 1300 ns)
  Bus period: 2920 ns (assuming 300 ns tf and tr)
  Bus speed: 342.5 kHz

Both tHIGH and tLOW are within the I2C specification.

The calculated values when ACPI parameters are not used are (in fast mode):

  HCNT: 87
  LCNT: 159

which translates to:

  tHIGH: 870 ns (spec min 600 ns)
  tLOW: 1590 ns (spec min 1300 ns)
  Bus period 3060 ns (assuming 300 ns tf and tr)
  Bus speed 326.8 kHz

These values are also within the I2C specification.

Since both ACPI and calculated values meet the I2C specification timing
requirements it is hard to say why the touchpad does not function properly
with the ACPI values except that the bus speed is higher in this case (but
still well below the max 400kHz).

Solve this by adding DMI quirk to the driver that disables using ACPI
parameters on this particulare machine.

Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2015-10-18 14:11:08 +02:00
Wolfram Sang
36d48fb576 i2c: designware-platdrv: enable RuntimePM before registering to the core
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@kernel.org
2015-10-15 14:28:07 +02:00
Wolfram Sang
eadd709f5d i2c: s3c2410: enable RuntimePM before registering to the core
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Kukjin Kim <kgene@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2015-10-15 14:26:07 +02:00
Wolfram Sang
4f7effddf4 i2c: rcar: enable RuntimePM before registering to the core
The core may register clients attached to this master which may use
funtionality from the master. So, RuntimePM must be enabled before, otherwise
this will fail. While here, move drvdata, too.

Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2015-10-15 14:25:56 +02:00
Jarkko Nikula
d80d134182 i2c: designware: Move common probe code into i2c_dw_probe()
There is some code duplication in i2c-designware-platdrv and
i2c-designware-pcidrv probe functions. What is even worse that duplication
requires i2c_dw_xfer(), i2c_dw_func() and i2c_dw_isr() i2c-designware-core
functions to be exported.

Therefore move common code into new i2c_dw_probe() and make functions above
local to i2c-designware-core.

While merging the code patch does following functional changes:

- I2C Adapter name will be "Synopsys DesignWare I2C adapter". Previously it
  was used for platform and ACPI devices but PCI device used
  "i2c-designware-pci".
- Using device name for interrupt name. Previous it was platform device name,
  ACPI device name or "i2c-designware-pci".
- Error code from devm_request_irq() and i2c_add_numbered_adapter() will be
  printed in case of error.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-15 14:09:37 +02:00
Jarkko Nikula
6ad6fde397 i2c: designware: Rename platform driver probe and PM functions
Make it easier to distinguish between i2c-designware-platdrv and
i2c-designware-core functions and to be consistent with
i2c-designware-pcidrv.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-15 14:08:42 +02:00
Jarkko Nikula
8a43745952 i2c: designware: Make dw_readl() and dw_writel() static
dw_readl() and dw_writel() are not used outside of i2c-designware-core and
they are not exported so make them static and remove their forward
declaration.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-15 14:08:22 +02:00
Jarkko Nikula
f6ed2b79dc i2c: designware: Remove unused functions
i2c_dw_is_enabled() became unused by the commit be58eda775
("i2c: designware-pci: Cleanup driver power management") and
i2c_dw_enable() by the commit 3a48d1c08f ("i2c: prevent spurious
interrupt on Designware controllers").

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-15 14:08:00 +02:00
Jarkko Nikula
b9f84adcb8 i2c: designware: Disable interrupts before requesting PCI device interrupt
Device must not generate interrupts before registering the interrupt
handler so move i2c_dw_disable_int() before requesting it.

There are no known issues with this. The code has been here since commit
fe20ff5c7e ("i2c-designware: Add support for Designware core behind PCI
devices.").

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-15 14:07:38 +02:00
Jarkko Nikula
c335631a68 i2c: designware: Remove interrupt clearing from i2c_dw_pci_probe()
There is no need to clear interrupts in i2c_dw_pci_probe() since only place
where interrupts are unmasked is i2c_dw_xfer_init() and there interrupts
are always cleared after commit 2a2d95e9d6 ("i2c: designware: always
clear interrupts before enabling them").

This allows to cleanup the code and replace i2c_dw_clear_int() in
i2c_dw_xfer_init() by direct register read as there are no other callers.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-15 14:07:19 +02:00
Kieran Bingham
74cedd3052 i2c: return probe deferred status on dev_pm_domain_attach
A change of return status was introduced in commit 3fffd12839
("i2c: allow specifying separate wakeup interrupt in device tree")

The commit prevents the defer status being passed up the call stack
appropriately when dev_pm_domain_attach returns -EPROBE_DEFER.

Catch the PROBE_DEFER and clear up the IRQ wakeup status

Signed-off-by: Kieran Bingham <kieranbingham@gmail.com>
Fixes: 3fffd12839 ("i2c: allow specifying separate wakeup interrupt in device tree")
Reviewed-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-15 13:35:32 +02:00
Christoph Hellwig
2f8e2c8777 move io-64-nonatomic*.h out of asm-generic
These are not implementations of default architecture code but helpers
for drivers. Move them to the place they belong to.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Acked-by: Hitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2015-10-15 00:21:07 +02:00
Sifan Naeem
58b0497dad i2c: img-scb: verify support for requested bit rate
The requested bit rate can be outside the range supported by the driver.
The maximum bit rate this driver supports at the moment is 400Khz.

If the requested bit rate is larger than the maximum supported by the
driver, set the bitrate to the maximum supported before bitrate_khz is
calculated.

Maximum speed supported by the driver can be increased to 1Mhz by
adding support for "fast plus mode" in the future.

Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-10 08:40:11 +01:00
Sifan Naeem
1ed6faedfc i2c: img-scb: Clear line and interrupt status before starting a transfer
Clear line status and all generated interrupts from the interrupt
status register before starting a transfer, as we may have
unserviced interrupts from previous transfers that might be
handled in the context of the new transfer.

Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-10 08:39:45 +01:00
Sifan Naeem
0f0a318997 i2c: img-scb: use line_status instead of i2c->line_status
i2c->line_status accumulates the line status bits that have been seen
with each interrupt. As we're only interested in that bit from the
current interrupt, refer to line_status (the argument to img_i2c_auto)
instead of i2c->line_status.

Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-10 08:39:20 +01:00
Sifan Naeem
987008dbc4 i2c: img-scb: fix LOW and HIGH period values for the SCL clock
Currently, after determining the minimum value for the High period
(TCKH) the remainder of the internal clock pulses is set as the Low
period (TCKL). This causes the i2c clock duty cycle to be much less
than 50%.

Modify the starting position to TCKH and TCKL at 50% of the internal
clock, and adjusts the TCKH and TCKL values from there should the
minimum value for TCKL not be met. This results in duty cycles closer
to 50%.

Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-10 08:38:55 +01:00
Sifan Naeem
5728d95f24 i2c: img-scb: use DIV_ROUND_UP to round divisor values
Using % can be slow depending on the architecture.

Using DIV_ROUND_UP is nicer and more efficient way to do it.

Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-10 08:38:31 +01:00
Sifan Naeem
2aefb1bd41 i2c: img-scb: do dummy writes before fifo access
Move scb_wr_rd_fence to before reading from fifo and writing to
fifo to make sure the the first read/write is done after the required
number of cycles.

Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-10 08:38:06 +01:00
Sifan Naeem
0e59378bc0 i2c: img-scb: enable fencing for all versions of the ip
The code to read from the master read fifo, and write to the master
write fifo, checks a bit in an SCB register before every byte to
ensure that the fifo is not full (write fifo) or empty (read fifo).
Due to clock domain crossing inside the SCB block the updated value
of this bit is only visible after 2 cycles.

The scb_wr_rd_fence() function does 2 dummy writes (to the read-only
revision register), and it's called before reading from or writing to the
fifos to ensure that subsequent reads of the fifo status bits do not read
stale values.

As the 2 dummy writes are required in all versions of the ip, the version
check is dropped.

Fixes: commit 27bce457d5 ("i2c: img-scb: Add Imagination Technologies I2C SCB driver")
Signed-off-by: Sifan Naeem <sifan.naeem@imgtec.com>
Acked-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: James Hartley <james.hartley@imgtec.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-10 08:37:41 +01:00
Wolfram Sang
708ca40841 i2c: rcar: clean up after refactoring
Update the comments to match current behaviour. Shorten some comments.
Update copyrights.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-09 22:32:14 +01:00
Wolfram Sang
e5a7effa09 i2c: rcar: revoke START request early
If we don't clear START generation as soon as possible, it may cause
another message to be generated. To keep the race window as small as
possible, we clear it right at the beginning of the interrupt. We don't
need checking since we always want to stop START and STOP generation on
the next occasion after we started it.

This patch improves the situation but sadly does not completely fix it.
It is still to be researched if we can do better given this HW design.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-09 22:31:54 +01:00
Wolfram Sang
2151ba7584 i2c: rcar: check master irqs before slave irqs
Due to broken HW design, master IRQs are more timing critical, so give
them precedence over slave IRQ.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-09 22:31:34 +01:00
Wolfram Sang
315a1736a2 i2c: rcar: don't issue stop when HW does it automatically
The manual says (55.4.8.6) that HW does automatically send STOP after
NACK was received. My measuerments confirm that.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-09 22:31:13 +01:00
Wolfram Sang
2bc3c5a863 i2c: rcar: init new messages in irq
Setting up new messages was done in process context while handling a
message was in interrupt context. Because of the HW design, this IP core
is sensitive to timing, so the context switches were too expensive. Move
this setup to interrupt context as well.

In my test setup, this fixed the occasional 'data byte sent twice' issue
which a number of people have seen. It also fixes to send REP_START
after a read message which was wrongly send as a STOP + START sequence
before.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-09 22:30:53 +01:00
Wolfram Sang
344beeb23b i2c: rcar: refactor setup of a msg
We want to reuse this function later.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-09 22:30:32 +01:00
Wolfram Sang
738206dec9 i2c: rcar: remove spinlock
We make sure to reinit the HW in the timeout case; then we know that
interrupts are always disabled in the sections protected by the
spinlock. Thus, we can simply remove it which is a preparation for
further refactoring. While here, rename the timeout variable to
time_left which is way more readable.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-09 22:30:12 +01:00
Wolfram Sang
59daef909d i2c: rcar: remove unused IOERROR state
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-09 22:29:51 +01:00
Wolfram Sang
93c659d820 i2c: rcar: rework hw init
We don't need to init HW before every transfer since we know the HW
state then. HW init at probe time is enough. While here, add setting the
clock register which belongs to init HW. Also, set MDBS bit since not
setting it is prohibited according to the manual.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-10-09 22:29:28 +01:00
Linus Torvalds
acceba598e Merge branch 'i2c/for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
 "Features:

   - new drivers: Renesas EMEV2, register based MUX, NXP LPC2xxx
   - core: scans DT and assigns wakeup interrupts.  no driver changes needed.
   - core: some refcouting issues fixed and better API for that
   - core: new helper function for best effort block read emulation
   - slave framework: proper DT bindings and userspace instantiation
   - some bigger work for xiic, pxa, omap drivers

  .. and quite a number of smaller driver fixes, cleanups, improvements"

* 'i2c/for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (65 commits)
  i2c: mux: reg Change ioread endianness for readback
  i2c: mux: reg: fix compilation warnings
  i2c: mux: reg: simplify register size checking
  i2c: muxes: fix leaked i2c adapter device node references
  i2c: allow specifying separate wakeup interrupt in device tree
  of/irq: export of_get_irq_byname()
  i2c: xgene-slimpro: dma_mapping_error() doesn't return an error code
  i2c: Replace I2C_CROS_EC_TUNNEL dependency
  eeprom: at24: use i2c_smbus_read_i2c_block_data_or_emulated
  i2c: core: Add support for best effort block read emulation
  i2c: lpc2k: add driver
  i2c: mux: Add register-based mux i2c-mux-reg
  i2c: dt: describe generic bindings
  i2c: slave: print warning if slave flag not set
  i2c: support 10 bit and slave addresses in sysfs 'new_device'
  i2c: take address space into account when checking for used addresses
  i2c: apply DT flags when probing
  i2c: make address check indpendent from client struct
  i2c: rename address check functions
  i2c: apply address offset for slaves, too
  ...
2015-09-08 16:16:26 -07:00
Linus Torvalds
8bd8fd0a29 - New Device Support
- New Clocksource driver from ST
    - New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
    - Add support for Arizona WM8998 and WM1814
    - Add support for Dialog Semi DA9062 and DA9063
    - Add support for Kontron COMe-bBL6 and COMe-cBW6
    - Add support for X-Powers AXP152
    - Add support for Atmel, many
    - Add support for STMPE, many
    - Add support for USB in X-Powers AXP22X
 
  - Core Frameworks
    - New Base API to traverse devices and their children in reverse order
 
  - Bug Fixes
    - Fix race between runtime-suspend and IRQs
    - Obtain platform data form more reliable source
 
  - Fix-ups
    - Constifying things
    - Variable signage changes
    - Kconfig depends|selects changes
    - Make use of BIT() macro
    - Do not supply .owner attribute in *_driver structures
    - MAINTAINERS entries
    - Stop using set_irq_flags()
    - Start using irq_set_chained_handler_and_data()
    - Export DT device ID structures
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJV6FCRAAoJEFGvii+H/HdhO2MP/1GxcbbywMXU4goj40gJaYfx
 kk0zH0S7i8+A8hD7SoCIQNkWN5o7i6sNYUA6sCTnPqixbyrkduWCyid1XsATu+41
 iiKEGyiCRyEHhCwnwCXvaFhpAZBzDi7FKj6hhf6nnRMHSEqwrs2aBqWgzNrOZTs0
 u66i/JHccnDdfHHm9Y7XcKMA8pWVqRMnwwaHreuYTFqfrEB0UGCYpmEeEBynGVKh
 MUGC0lCUrEKp59aOexZRtBUla/5BeALJd//vMQtf/+D0YPvE8lppDNwkgCe4buXN
 ZlNHDQooIWIiZfTj7wbHaTWjrBK7MsOEHWBUjNsk2nyDvDOJoGhTrSdJwPeyhUSh
 d2eUyW6sPEQY21XPwuD0DhfRKYKLOzVRhIcxvjlRAq9QHDWVXKyIlf3M70fculK8
 5FN1Wb6Sc2h0OvMC5RemPpxMwZSq6Ks3XANa718Ju802TGK/xk6iRqhZrEut/qrN
 rLYsU84TLUz6YindozTiI5FrGo+zSp9OlUU4z7HUh+4t3H5/opdsRjRp0ICwgIbY
 NxAmsk2d/vJ7xX7FAAjwMY2rPIC0zIksbGEe1AJweWV455EcDMaBM1/e9zDzHciI
 TXVxbzs3DFBadtQWlLv/VkwZmt43MTI8g6ozTTJJkPQNCKThtz4bvDSu8rQWqFua
 bkbRyQroraX5fM0Q3HIs
 =2blS
 -----END PGP SIGNATURE-----

Merge tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull MFD updates from Lee Jones:
 "New Device Support:
   - New Clocksource driver from ST
   - New MFD/ACPI/DMA drivers for Intel's Sunrisepoint PCH based platforms
   - Add support for Arizona WM8998 and WM1814
   - Add support for Dialog Semi DA9062 and DA9063
   - Add support for Kontron COMe-bBL6 and COMe-cBW6
   - Add support for X-Powers AXP152
   - Add support for Atmel, many
   - Add support for STMPE, many
   - Add support for USB in X-Powers AXP22X

  Core Frameworks:
   - New Base API to traverse devices and their children in reverse order

  Bug Fixes:
   - Fix race between runtime-suspend and IRQs
   - Obtain platform data form more reliable source

  Fix-ups:
   - Constifying things
   - Variable signage changes
   - Kconfig depends|selects changes
   - Make use of BIT() macro
   - Do not supply .owner attribute in *_driver structures
   - MAINTAINERS entries
   - Stop using set_irq_flags()
   - Start using irq_set_chained_handler_and_data()
   - Export DT device ID structures"

* tag 'mfd-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (69 commits)
  mfd: jz4740-adc: Init mask cache in generic IRQ chip
  mfd: cros_ec: spi: Add OF match table
  mfd: stmpe: Add OF match table
  mfd: max77686: Split out regulator part from the DT binding
  mfd: Add DT binding for Maxim MAX77802 IC
  mfd: max77686: Use a generic name for the PMIC node in the example
  mfd: max77686: Don't suggest in binding to use a deprecated property
  mfd: Add MFD_CROS_EC dependencies
  mfd: cros_ec: Remove CROS_EC_PROTO dependency for SPI and I2C drivers
  mfd: axp20x: Add a cell for the usb power_supply part of the axp20x PMICs
  mfd: axp20x: Add missing registers, and mark more registers volatile
  mfd: arizona: Fixup some formatting/white space errors
  mfd: wm8994: Fix NULL pointer exception on missing pdata
  of: Add vendor prefix for Nuvoton
  mfd: mt6397: Implement wake handler and suspend/resume to handle wake up event
  mfd: atmel-hlcdc: Add support for new SoCs
  mfd: Export OF module alias information in missing drivers
  mfd: stw481x: Export I2C module alias information
  mfd: da9062: Support for the DA9063 OnKey in the DA9062 core
  mfd: max899x: Avoid redundant irq_data lookup
  ...
2015-09-04 11:35:03 -07:00
York Sun
5a73882fd2 i2c: mux: reg Change ioread endianness for readback
Reading the register (if allowed) after writing is to ensure writing
is completed on a posted bus. The endianness of reading doesn't matter.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-09-03 11:58:42 +02:00
Mike Rapoport
a05a34e7f6 i2c: mux: reg: fix compilation warnings
With CONFIG_OF=n, the following warnings occur when compiling
drivers/i2c/muxes/i2c-mux-reg.c:

  CC      drivers/i2c/muxes/i2c-mux-reg.o
drivers/i2c/muxes/i2c-mux-reg.c:170:13: warning: ‘struct gpiomux’ declared inside parameter list [enabled by default]
      struct platform_device *pdev)
             ^
drivers/i2c/muxes/i2c-mux-reg.c:170:13: warning: its scope
is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/i2c/muxes/i2c-mux-reg.c: In function ‘i2c_mux_reg_probe’:
drivers/i2c/muxes/i2c-mux-reg.c:201:3: warning: passing argument 1 of ‘i2c_mux_reg_probe_dt’ from incompatible pointer type [enabled by default]
   ret = i2c_mux_reg_probe_dt(mux, pdev);
   ^

Signed-off-by: Mike Rapoport <mike.rapoport@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-09-03 11:56:23 +02:00
Wolfram Sang
fce388afd6 i2c: mux: reg: simplify register size checking
Checking was done at three different locations, just do it once and
properly at probing time.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Tested-by: York Sun <yorksun@freescale.com>
2015-09-03 11:54:41 +02:00
Vladimir Zapolskiy
bdbf4a29ee i2c: muxes: fix leaked i2c adapter device node references
Every call of of_parse_phandle() increments user count of found device
node, if OF_DYNAMIC is enabled.

The change fixes all similar addressed cases in drivers/i2c.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-31 22:40:34 +02:00
Dmitry Torokhov
3fffd12839 i2c: allow specifying separate wakeup interrupt in device tree
Instead of having each i2c driver individually parse device tree data in
case it or platform supports separate wakeup interrupt, and handle
enabling and disabling wakeup interrupts in their power management
routines, let's have i2c core do that for us.

Platforms wishing to specify separate wakeup interrupt for the device
should use named interrupt syntax in their DTSes:

	interrupt-parent = <&intc1>;
	interrupts = <5 0>, <6 0>;
	interrupt-names = "irq", "wakeup";

This patch is inspired by work done by Vignesh R <vigneshr@ti.com> for
pixcir_i2c_ts driver.

Note that the original code tried to preserve any existing wakeup
settings from userspace but was not quite right in that regard:
it would preserve wakeup flag set by userspace upon driver rebinding;
but it would re-arm the wakeup flag if it was disabled by userspace.

We think that resetting the flag upon re-binding the driver is proper
behavior as the driver is responsible for setting up and handling
wakeups.

Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Vignesh R <vigneshr@ti.com>
[wsa: updated the commit message]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-26 18:47:58 +02:00
Dan Carpenter
a4a9a8cb32 i2c: xgene-slimpro: dma_mapping_error() doesn't return an error code
The dma_mapping_error() function returns true if there is an error, it
doesn't return an error code.  We should return -ENOMEM.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
2015-08-24 14:23:31 +02:00
Javier Martinez Canillas
480b141abf i2c: Replace I2C_CROS_EC_TUNNEL dependency
The ChromeOS EC tunnel I2C bus driver depend on CROS_EC_PROTO but
MFD_CROS_EC select CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.

Since the platform device that is matched with the I2C bus driver
is registered by the ChromeOS EC mfd driver, I2C_CROS_EC_TUNNEL
really depends on MFD_CROS_EC. And because this config option
selects CROS_EC_PROTO, that dependency is met as well. So make the
driver to depend on MFD_CROS_EC instead of CROS_EC_PROTO.

Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-24 14:17:53 +02:00
Irina Tirdea
01eef96e37 i2c: core: Add support for best effort block read emulation
There are devices that need to handle block transactions
regardless of the capabilities exported by the adapter.
For performance reasons, they need to use i2c read blocks
if available, otherwise emulate the block transaction with word
or byte transactions.

Add support for a helper function that would read a data block
using the best transfer available: I2C_FUNC_SMBUS_READ_I2C_BLOCK,
I2C_FUNC_SMBUS_READ_WORD_DATA or I2C_FUNC_SMBUS_READ_BYTE_DATA.

Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-24 14:05:19 +02:00
Joachim Eastwood
3f9c37a0c9 i2c: lpc2k: add driver
Add support for the I2C controller found on several NXP devices
including LPC2xxx, LPC178x/7x and LPC18xx/43xx. The controller
is implemented as a state machine and the driver act upon the
state changes when the bus is accessed.

The I2C controller supports master/slave operation, bus
arbitration, programmable clock rate, and speeds up to 1 Mbit/s.

Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-24 14:05:18 +02:00
York Sun
b3fdd32799 i2c: mux: Add register-based mux i2c-mux-reg
Based on i2c-mux-gpio driver, similarly the register-based mux
switch from one bus to another by setting a single register.
The register can be on PCIe bus, local bus, or any memory-mapped
address. The endianness of such register can be specified in device
tree if used, or in platform data.

Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-24 14:05:18 +02:00
Wolfram Sang
c6909d6f6f i2c: slave: print warning if slave flag not set
Address collisions will be rare, but we should let the user know that
slaves have their own address space nonetheless.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-24 14:05:16 +02:00
Wolfram Sang
cfa0327b0d i2c: support 10 bit and slave addresses in sysfs 'new_device'
We now have seperate address spaces for 10 bit and we-are-slave clients.
Update the sysfs device instantiation method to support these types by
accepting the address offsets that are assigned to the extra address
spaces. Update the documentation, too.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-24 14:05:15 +02:00
Wolfram Sang
9bccc70a12 i2c: take address space into account when checking for used addresses
It is not enough to compare the plain address value, we also need to
check the flags enabling a different address space. E.g. it is valid to
have address 0x50 as a 7-bit address and 0x050 as 10-bit address on the
same bus. Same for addresses when we are the slave.

Tested-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-24 14:05:14 +02:00
Wolfram Sang
b4e2f6ac12 i2c: apply DT flags when probing
Check for slave and 10-bit flags when probing and mark the client when
found. Improve the address validity check, too

Tested-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-24 14:05:14 +02:00
Wolfram Sang
c4019b7040 i2c: make address check indpendent from client struct
We want to use this function with struct boardinfo soon, so let's just
pass the parameters really needed. We also extend the type of addr, so
more types can be input. Remove a superfluous dangling comment while
here.

Tested-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-24 14:05:13 +02:00
Wolfram Sang
66be6056eb i2c: rename address check functions
The current naming is based on the arguments of the functions and not on
what they do. Even I as the maintainer find this confusing, so let's
rename them to something more descriptive.

Tested-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-24 14:05:12 +02:00
Wolfram Sang
da899f55b3 i2c: apply address offset for slaves, too
We want a separate address range for being an I2C slave. Add an offset
of 0x1000, so it can be combined with ten bit addresses as well. Add a
separate function to create the address value, we will need it later in
other places.

Tested-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-24 14:05:11 +02:00
Eddie Huang
28c0a8433d i2c: mediatek: Fixup i2c ack error interrupt handling
When occur i2c ack error, i2c controller generate two interrupts,
first is the ack error interrupt, then the complete interrupt.
i2c interrupt handler should keep the two interrupt value, and only
call complete() for the complete interrupt.

Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-11 16:54:47 +02:00
Eddie Huang
ea89ef1f7b i2c: mediatek: Reset DMA engine in hardware init function
Reset DMA in hardware init function to avoid unknown hardware state
before do any I2C operation.

Signed-off-by: Liguo Zhang <liguo.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-11 16:53:11 +02:00
Mika Westerberg
9424693035 i2c: i801: Create iTCO device on newer Intel PCHs
Starting from Intel Sunrisepoint (Skylake PCH) the iTCO watchdog resources
have been moved to reside under the i801 SMBus host controller whereas
previously they were under the LPC device.

In order to support the iTCO watchdog on newer PCHs we need to create the
platform device here in the SMBus driver and pass all known resources using
platform data.

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-08-11 15:03:51 +01:00
Colin Ian King
66621f96c9 i2c: viperboard: clean up inconsistent indenting
Minor clean up of indenting, no functional change

Signed-off-by: Colin Ian King <colin.king@canonical.com>
[wsa: squashed two lines into one]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:38 +02:00
Masahiro Yamada
a1f64317bb i2c: cadence: set THIS_MODULE to the owner of the adapter
The owner of the adapter is missing, while this driver is tristate.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:38 +02:00
Jarkko Nikula
fb427466dc i2c: designware: Make debug print in i2c_dw_isr() shorter
Printing adapter name is irrelevant from this debug print and makes output
needlessly long. Having already device and functions names printed here is
enough for debugging.

While at it remove extra space from "enabled= 0x" and use "%#x" for
printing "0x" prefixed hexadecimal values.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
[wsa: made it a oneliner]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:36 +02:00
Vladimir Zapolskiy
0d1ad98dd8 i2c: arb-gpio-challenge: use of_get_i2c_adapter_by_node interface
This change is needed to properly lock I2C parent bus driver.

Prior to this change i2c_put_adapter() is misused, which may lead
to an overflow over zero of I2C bus driver user counter.

Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:36 +02:00
Vladimir Zapolskiy
48e9743dd6 i2c: core: add and export of_get_i2c_adapter_by_node() interface
of_find_i2c_adapter_by_node() call requires quite often missing
put_device(), and i2c_put_adapter() releases a device locked by
i2c_get_adapter() only. In general module_put(adapter->owner) and
put_device(dev) are not interchangeable.

This is a common error reproduction scenario as a result of the
misusage described above (for clearness this is run on iMX6 platform
with HDMI and I2C bus drivers compiled as kernel modules):

    root@mx6q:~# lsmod | grep i2c
    i2c_imx                10213  0
    root@mx6q:~# lsmod | grep dw_hdmi_imx
    dw_hdmi_imx             3631  0
    dw_hdmi                11846  1 dw_hdmi_imx
    imxdrm                  8674  3 dw_hdmi_imx,imx_ipuv3_crtc,imx_ldb
    drm_kms_helper        113765  5 dw_hdmi,imxdrm,imx_ipuv3_crtc,imx_ldb
    root@mx6q:~# rmmod dw_hdmi_imx
    root@mx6q:~# lsmod | grep i2c
    i2c_imx                10213  -1

                                 ^^^^^

    root@mx6q:~# rmmod i2c_imx
    rmmod: ERROR: Module i2c_imx is in use

To fix existing users of these interfaces and to avoid any further
confusion and misusage in future, add one more interface
of_get_i2c_adapter_by_node(), it is similar to i2c_get_adapter() in
sense that an I2C bus device driver found and locked by user can be
correctly unlocked by i2c_put_adapter().

Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:36 +02:00
Vladimir Zapolskiy
611e12ea0f i2c: core: manage i2c bus device refcount in i2c_[get|put]_adapter
In addition to module_get()/module_put() add get_device()/put_device()
calls into i2c_get_adapter()/i2c_put_adapter() exported
interfaces. This is done to lock I2C bus device, if it is in use by a
client.

Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:35 +02:00
Krzysztof Kozlowski
069d5b745b i2c: Drop owner assignment from i2c_driver
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.

Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:35 +02:00
Andy Shevchenko
b0898fdaff i2c: designware-pci: use IRQF_COND_SUSPEND flag
The mentioned flag fixes a warning on Intel Edison board since one of the I2C
controller shares IRQ line with watchdog timer.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:35 +02:00
Ondrej Zary
82cd5d041c i2c: parport: Add VCT-jig adapter
Add support for VCT-jig parallel port I2C adapter to i2c-parport.

The adapter schematic can be found here (in the RAR file):
http://remont-aud.net/shop/22/desc/vct-jig-komplekt-dlja-samostojatelnoj-sborki

Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:34 +02:00
Anurag Kumar Vulisha
63cab195bf i2c: removed work arounds in i2c driver for Zynq Ultrascale+ MPSoC
Cadence 1.0 version has bugs which have been fixed in the cadence 1.4 version.
This patch removes the quirks present in the driver for cadence 1.4 version.

Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
[wsa: fixed indentation issues in r1p10_i2c_def]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:34 +02:00
Laxman Dewangan
d57f5dedde i2c: tegra: add support for fast plus (FM+) mode clock rate
Tegra I2C controller required to configure the clock divisor
register inside controller to different value based on the clock
speed. The recommended clock divisor for the I2C controller for
standard/fast mode is 0x19 and for fast-mode plus is 0x10.

Add support to configure clock divisor register of I2C controller
based on bus clock rate.

This clock divisor is supported form T114 onwards.

Signed-off-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:33 +02:00
Laxman Dewangan
6f4664b2e2 i2c: tegra: update CONFIG_LOAD for new conifiguration
Once the new configuration is set on the conifg register of
I2C controller, it is require to update the CONFIG_LOAD register
to transfer the new SW configuration to actual HW internal
registers that would be used in the actual logic.

It is like, SW is programming only shadow registers through
regular configuration and when these load_config bit fields
are set to 1, it causes the regular/shadows registers
configuration transferred to the HW internal active registers.
So SW has to set these bit fields at the end of all regular
registers configuration. And these config_load bits are HW
auto-clear bits. HW clears these bit fields once the register
configuration is moved to HW internal active registers. So SW
has to wait until these bits are auto-cleared before going
for any further programming

This mechanism is supported on T124 and after this SoCs.

Signed-off-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:33 +02:00
Wolfram Sang
77441ac00d i2c: omap: fix cleanup regression
Patch "i2c: omap: abolish variable name confusion" triggered a
coccinelle warning which we fix here:

drivers/i2c/busses/i2c-omap.c:1333:5-24: pm_runtime_get_sync returns < 0 as error. Unecessary IS_ERR_VALUE at line 1334

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:33 +02:00
Shubhrajyoti Datta
6b0c8dc310 i2c: xiic: Do not continue in case of errors in Rx
In case of error conditions like Arbitration lost or NACK lets signal
the waiting process.

Handle error cases in the Rx path

Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:33 +02:00
Shubhrajyoti Datta
7f9906bd7f i2c: xiic: Service all interrupts in isr
Currently only one interrupt is serviced in the isr.
In case the multiple interrupts happen simultenously we service and ack
only one of them. Check for all the causes in the isr and service them.

Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:32 +02:00
Shubhrajyoti Datta
542e2a9b73 i2c: xiic: Remove the Addressed as slave interrupt
Currently there is no slave mode support in the driver
also in the isr we just ack it and do nothing.
So disable the AAS interrupt.

Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:32 +02:00
Shubhrajyoti Datta
b33aa25278 i2c: xiic: Remove busy loop while waiting for bus busy
Remove the busy loop  while waiting for bus busy.
Instead let the processor sleep.

Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:32 +02:00
Shubhrajyoti Datta
e6c9a037bc i2c: xiic: Remove the disabling of interrupts
Currently before every transfer the interrupts are disabled.
So incase the slave nacks in the middle of the transfer the
current transfer is not aborted. Upon enabling the interrupts
conditions like NACK , arbitration lost will not be masked.
Remove the disabling of the interrupts.

Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:32 +02:00
Shubhrajyoti Datta
d701667bb3 i2c: xiic: Do not reset controller before every transfer
Currently before every transfer the controller is reinitialised.
We are already resetting the controller upon errors so upon every
transfer is a performance kill.
Remove the same.

Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:31 +02:00
Shubhrajyoti Datta
fcc2fac60a i2c: xiic: move the xiic_process to thread context
The xiic_process is a 154 line code that runs in isr context currently
move it to thread context. Also the name xiic_process suggests that the
intension was to run in process context.

Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
[wsa: initialized irqreturn_t to IRQ_NONE instead of IRQ_HANDLED]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:31 +02:00
Shubhrajyoti Datta
0387fc1645 i2c: xiic: Remove the disabling of interrupts
Currently the interrupts are disabled at the start of the
isr and enabled at the end of the isr. Remove the same.

In case the slave device NACKs the transaction while in the isr
the transfer will continue and the NACK interrupt will arrive
only after the isr is serviced.

Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:31 +02:00
Vaibhav Hiremath
51fcce86a7 i2c: pxa: Use devm_ variants in probe function
This patch cleans up i2c_pxa_probe() function,

 - Use devm_ variants wherever
   This will clean both probe exit and i2c_pxa_remove() functions

 - Check platform resource before parsing any other data from DT/platform

 - Use dev_err on failure from i2c_add_numbered_adapter()

 - Use pr_info instead of printk for KERN_INFO

Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
[wsa: removed unneeded error prinout after devm_ioremap_resource]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:31 +02:00
Vaibhav Hiremath
3a2dc1677b i2c: pxa: Update debug function to dump more info on error
Update i2c_pxa_scream_blue_murder() fn to print more information
in case of error.
Also, use dev_err variants instead of printk.

Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:30 +02:00
Yipeng Yao
e2b498fd55 i2c: pxa: Fix compile warning in 64bit mode
Fix below warning message, coming from 64 bit toolchain.

drivers/i2c/busses/i2c-pxa.c:1237:15:
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]

Signed-off-by: Yipeng Yao <ypyao@marvell.com>
[vaibhav.hiremath@linaro.org: Updated Changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:30 +02:00
Shouming Wang
8bd75bd303 i2c: pxa: Return I2C_RETRY when timeout in pio mode
In case of timeout in pio mode of operation return I2C_RETRY.
This behavior will be same as interrupt mode of operation.

Signed-off-by: Shouming Wang <wangshm@marvell.com>
[vaibhav.hiremath@linaro.org: Updated changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:30 +02:00
Vaibhav Hiremath
e087b4272e i2c: pxa: No need to set slave addr for i2c master mode reset
Normally i2c controller works as master, so slave addr is not needed, or
it will impact some slave device (eg. ST NFC chip) i2c accesses, because
it has the same i2c address with controller.

For example,
On the pxa1928 based platform, where PMIC (88pm860) is present @0x30
address on TWSI0 interface, and if we set 0x30 as a slave address in
pxa1928 TWSI0 module, all the transactions towards PMIC would go for toss.

Signed-off-by: Jett.Zhou <jtzhou@marvell.com>
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:29 +02:00
Leilei Shang
abf8a1fba9 i2c: pxa: keep i2c irq ON in suspend
During suspend there may still be some i2c access happening, as the
interrupt is shared between multiple drivers.
And if we don't keep i2c irq ON, there may be i2c access timeout if
i2c is in irq mode of operation.

Signed-off-by: Raul Xiong <xjian@marvell.com>
Signed-off-by: Xiaofan Tian <tianxf@marvell.com>
[vaibhav.hiremath@linaro.org: updated Changelog]
Signed-off-by: Vaibhav Hiremath <vaibhav.hiremath@linaro.org>
Cc: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:29 +02:00
Wolfram Sang
5faf6e1f58 i2c: emev2: add driver
Add a basic driver for the Renesas EMEV2 SoC. Based on the driver from
the BSP which was first worked on by Ian, and made ready for upstream by
me.

Signed-off-by: Ian Molton <ian.molton@codethink.co.uk>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:29 +02:00
Felipe Balbi
1c4828f916 i2c: omap: on ->remove() call pm_runtime_put_sync()
we're about to remove the module, so we can't
really schedule a PM transition in the future,
we must wait for it to finish.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:28 +02:00
Felipe Balbi
63f8f85625 i2c: omap: abolish variable name confusion
struct device pointers are usually called
dev. Calling our struct omap_i2c_dev pointers
also dev has caused enough confusion.

This is the result of a few simple sed rules
to convert all struct omap_i2c_dev pointers
to be called omap instead.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:28 +02:00
Felipe Balbi
c680e32918 i2c: omap: switch to dev_get_drvdata()
there's no need to fetch the platform_device
in order to dereference it back to the dev
pointer to access drvdata, we can use
dev_get_drvdata() instead.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:28 +02:00
Sudip Mukherjee
20226118bc i2c: parport: start using pr_fmt
Start using pr_fmt and convert all remaining printk to use
pr_* family of macros.

Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
[wsa: remove print on kzalloc failure]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:28 +02:00
Sudip Mukherjee
c5f3d544a7 i2c: parport: use dev_*
Now parport is using device model so use dev_* macros instead of printk.

Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-10 08:37:27 +02:00
Vladimir Zapolskiy
e331146973 i2c: fix leaked device refcount on of_find_i2c_* error path
If of_find_i2c_device_by_node() or of_find_i2c_adapter_by_node() find
a device by node, but its type does not match, a reference to that
device is still held. This change fixes the problem.

Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-08-01 12:11:58 +02:00
Masanari Iida
e952849a02 i2c: Fix typo in i2c-bfin-twi.c
This patch fix some typos found in a printk message and
MODULE_DESCRIPTION.

Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-31 13:32:31 +02:00
Jan Luebbe
828e66c0ed i2c: omap: fix bus recovery setup
At least on the AM335x, enabling OMAP_I2C_SYSTEST_ST_EN is not enough to
allow direct access to the SCL and SDA pins. In addition to ST_EN, we
need to set the TMODE to 0b11 (Loop back & SDA/SCL IO mode select).
Also, as the reset values of SCL_O and SDA_O are 0 (which means "drive
low level"), we need to set them to 1 (which means "high-impedance") to
avoid unwanted changes on the pins.

As a precaution, reset all these bits to their default values after
recovery is complete.

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-31 13:32:31 +02:00
Jan Luebbe
8b06260836 i2c: core: only use set_scl for bus recovery after calling prepare_recovery
Using set_scl may be ineffective before calling the driver specific
prepare_recovery callback, which might change into a test mode. So
instead of setting SCL in i2c_generic_scl_recovery, move it to
i2c_generic_recovery (after the optional prepare_recovery).

Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Acked-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-31 13:32:31 +02:00
Vladimir Zapolskiy
1f023297f7 i2c: slave eeprom: clean up sysfs bin attribute read()/write()
The change removes redundant sysfs binary file boundary checks,
since this task is already done on caller side in fs/sysfs/file.c

Note, on file size overflow read() now returns 0, and this is a
correct and expected EOF notification according to POSIX.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-31 13:32:30 +02:00
Pantelis Antoniou
4f001fd301 i2c: Mark instantiated device nodes with OF_POPULATE
Mark (and unmark) device nodes with the POPULATE flag as appropriate.
This is required to avoid multi probing when using I2C and device
overlays containing a mux.
This patch is also more careful with the release of the adapter device
which caused a deadlock with muxes, and does not break the build
on !OF since the node flag accessors are not defined then.

Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-09 22:25:54 +02:00
Axel Lin
eb8173e3d7 i2c: jz4780: Fix return value if probe fails
Current code returns 0 if fails to read clock-frequency DT property,
fix it. Also add checking return value of clk_prepare_enable and
propagate return value of devm_request_irq.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-09 22:17:31 +02:00
Axel Lin
724948106e i2c: xgene-slimpro: Fix missing mbox_free_channel call in probe error path
Free requested mailbox channel before return error.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-09 22:13:10 +02:00
Geert Uytterhoeven
fc0a1f035c i2c: I2C_MT65XX should depend on HAS_DMA
If NO_DMA=y:

    ERROR: "dma_unmap_single" [drivers/i2c/busses/i2c-mt65xx.ko] undefined!
    ERROR: "dma_mapping_error" [drivers/i2c/busses/i2c-mt65xx.ko] undefined!
    ERROR: "dma_map_single" [drivers/i2c/busses/i2c-mt65xx.ko] undefined!

Add a dependency on HAS_DMA to fix this.

Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-07-09 22:10:20 +02:00
Linus Torvalds
d87823813f Char/Misc driver patches for 4.2-rc1
Here's the big char/misc driver pull request for 4.2-rc1.
 
 Lots of mei, extcon, coresight, uio, mic, and other driver updates in
 here.  Full details in the shortlog.  All of these have been in
 linux-next for some time with no reported problems.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlWNn0gACgkQMUfUDdst+ykCCQCgvdF4F2+Hy9+RATdk22ak1uq1
 JDMAoJTf4oyaIEdaiOKfEIWg9MasS42B
 =H5wD
 -----END PGP SIGNATURE-----

Merge tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc driver updates from Greg KH:
 "Here's the big char/misc driver pull request for 4.2-rc1.

  Lots of mei, extcon, coresight, uio, mic, and other driver updates in
  here.  Full details in the shortlog.  All of these have been in
  linux-next for some time with no reported problems"

* tag 'char-misc-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (176 commits)
  mei: me: wait for power gating exit confirmation
  mei: reset flow control on the last client disconnection
  MAINTAINERS: mei: add mei_cl_bus.h to maintained file list
  misc: sram: sort and clean up included headers
  misc: sram: move reserved block logic out of probe function
  misc: sram: add private struct device and virt_base members
  misc: sram: report correct SRAM pool size
  misc: sram: bump error message level on unclean driver unbinding
  misc: sram: fix device node reference leak on error
  misc: sram: fix enabled clock leak on error path
  misc: mic: Fix reported static checker warning
  misc: mic: Fix randconfig build error by including errno.h
  uio: pruss: Drop depends on ARCH_DAVINCI_DA850 from config
  uio: pruss: Add CONFIG_HAS_IOMEM dependence
  uio: pruss: Include <linux/sizes.h>
  extcon: Redefine the unique id of supported external connectors without 'enum extcon' type
  char:xilinx_hwicap:buffer_icap - change 1/0 to true/false for bool type variable in function buffer_icap_set_configuration().
  Drivers: hv: vmbus: Allocate ring buffer memory in NUMA aware fashion
  parport: check exclusive access before register
  w1: use correct lock on error in w1_seq_show()
  ...
2015-06-26 14:51:15 -07:00
Linus Torvalds
24867481b8 Merge branch 'i2c/for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
 "Highlights:

   - new drivers for Mediatek I2C, APM X-Gene, Broadcom Settop
   - major updates to at91, davinci
   - bugfixes to the mux infrastructure when dealing with the new quirk
     mechanism
   - more users for the bus recovery feature
   - further improvements to the slave framework

  Plus the usual bunch of smaller driver and core improvements and
  fixes.

  There is one patch removing old code from an ARM platform.  This has
  been acked by the sh_mobile maintainer Simon Horman"

* 'i2c/for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (48 commits)
  i2c: busses: i2c-bcm2835: limits cdiv to allowed values
  i2c: sh_mobile: use proper type for timeout
  i2c: sh_mobile: use adapter default for timeout
  i2c: rcar: use proper type for timeout
  i2c: rcar: use adapter default for timeout
  i2c: designware: Make sure the device is suspended before disabling runtime PM
  i2c: tegra: apply size limit quirk
  i2c: tegra: don't advertise SMBUS_QUICK
  i2c: octeon: remove unused signal handling
  i2c: davinci: Optimize SCL generation
  i2c: mux: pca954x: Use __i2c_transfer because of quirks
  i2c: mux: Use __i2c_transfer() instead of calling parent's master_xfer()
  i2c: use parent adapter quirks in mux
  i2c: bcm2835: clear reserved bits in S-Register
  ARM: shmobile: r8a7740: remove I2C errata handling
  i2c: sh_mobile: add errata workaround
  i2c: at91: fix code checker warnings
  i2c: busses: xgene-slimpro: fix incorrect __init declation for probe
  i2c: davinci: Avoid sending to own address
  i2c: davinci: Refactor i2c_davinci_wait_bus_not_busy()
  ...
2015-06-25 18:42:39 -07:00
Linus Torvalds
84e9c87e6f == Changes to existing drivers ==
- Constify structures; throughout the subsystem
    - Move support to DT in; cros_ec
    - DT changes and documentation; cros-ec, max77693, max77686, arizona, da9063
    - ACPI changes and documentation; mfd-core
    - Use different platform specific API in; cros_ec_*, arizona-core
    - Remove unused parent field from; cros_ec_i2c
    - Add wake-up/reset delay in; cross_ec_spi, arizona-core
    - Staticise structures/functions in; cros_ec
    - Remove redundant code; arizona-core, max77686
    - Bugfix; twl4030-power
    - Allow compile test; aat2870, tps65910
    - MAINTAINERS adaptions; samsung, syscon
    - Resource Management (devm_*); arizona-core
    - Refactor Reset code; arizona-core
    - Insist on at least one full boot; arizona-core
    - Trivial formatting; arizona-core
    - Add low-power-sleep; arizona-core
    - IRQ ONESHOT changes; twl4030-irq, mc13xxx-core, wm831x-auxadc, htc-i2cpld,
                           wm8350-core, ab8500-debugfs, ab8500-gpadc, si476x-i2c
 
  == (Re-)moved drivers ==
    - Move protocol helpers out to drivers/platform; cros_ec
 
  == New drivers/supported devices ==
    - Add support for AXP22x into axp20x
    - Add support for OnKey into da9063-core
    - Add support for Pinctrl into mt6397-core
    - New STMicroelectronics LPC Watchdog driver
    - New STMicroelectronics LPC Real-Time Clock driver
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJViWsQAAoJEFGvii+H/HdhBSEP/1nBi6iCwAb0gGJ5HeVKAVGa
 bF9EYM3wMEu64Rb3b4CZGVaI2DWy148vsyDdoOht6gRpaGk9yWz4KR9saG0cemKe
 NC1fqOrY+a6FytqJOcQ51fhcXAn49uqAOzJsTZX3AQ4Z93EXT3ZhF8/shXqUXNc1
 rXzV5enMwco9xnc3+0qzJoA0RaFfZuLB33bxt53GmnJVdnc5b1Haj5t40IN2oDSd
 3pA2MQqVw/j4rGwsYOoTkJHK792X969BJHj9AHESwFYz87/u2f8RQin5xi3RWN/M
 1XtkvURZESA+ewPWbOsq6wiVZd/wm4i2knoqWeXx0S5uKpi48PaljgY/PNYt8cOt
 oC1kVA5oOFIksdue7HG+mJ1EdAd38m3OGDJrivfFCfn8O8U+wsVrmrpS/hPuWQr6
 JTsZKapS77vty+jDSHrCU/F1rd5M7fVucxHqum0YCHz6w+B5CYWY3+qLcVa5zimi
 f3LbcuWI5XsNzuAsW3iqF1M+bPT6G9GRJV30FczX7KQkLNT0++q62lMF4K3mz93m
 avtrmZxFrF0yAP1n4Molz5x8JgfWdyvCSuGGxxfYmGf2v4taLW2BSRFRrWE3WwN3
 KQDzcftt3R7CM50wkIVqKJwBP7pA/UV+PPaRopbPqsdeXnkL+EoYyOpDuQkKsblz
 Q5M3ChB5rsu8trNyMPI6
 =Y02f
 -----END PGP SIGNATURE-----

Merge tag 'mfd-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd

Pull MFD updates from Lee Jones:
 "Changes to existing drivers:
   - Constify structures; throughout the subsystem
   - Move support to DT in; cros_ec
   - DT changes and documentation; cros-ec, max77693, max77686, arizona, da9063
   - ACPI changes and documentation; mfd-core
   - Use different platform specific API in; cros_ec_*, arizona-core
   - Remove unused parent field from; cros_ec_i2c
   - Add wake-up/reset delay in; cross_ec_spi, arizona-core
   - Staticise structures/functions in; cros_ec
   - Remove redundant code; arizona-core, max77686
   - Bugfix; twl4030-power
   - Allow compile test; aat2870, tps65910
   - MAINTAINERS adaptions; samsung, syscon
   - Resource Management (devm_*); arizona-core
   - Refactor Reset code; arizona-core
   - Insist on at least one full boot; arizona-core
   - Trivial formatting; arizona-core
   - Add low-power-sleep; arizona-core
   - IRQ ONESHOT changes; twl4030-irq, mc13xxx-core, wm831x-auxadc, htc-i2cpld,
                          wm8350-core, ab8500-debugfs, ab8500-gpadc, si476x-i2c

  (Re-)moved drivers:
   - Move protocol helpers out to drivers/platform; cros_ec

  New drivers/supported devices:
   - Add support for AXP22x into axp20x
   - Add support for OnKey into da9063-core
   - Add support for Pinctrl into mt6397-core
   - New STMicroelectronics LPC Watchdog driver
   - New STMicroelectronics LPC Real-Time Clock driver"

* tag 'mfd-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (59 commits)
  mfd: lpc_ich: Assign subdevice ids automatically
  mfd: si476x-i2c: Pass the IRQF_ONESHOT flag
  mfd: ab8500-gpadc: Pass the IRQF_ONESHOT flag
  mfd: ab8500-debugfs: Pass the IRQF_ONESHOT flag
  mfd: wm8350-core: Pass the IRQF_ONESHOT flag
  mfd: htc-i2cpld: Pass the IRQF_ONESHOT flag
  mfd: wm831x-auxadc: Pass the IRQF_ONESHOT flag
  mfd: mc13xxx-core: Pass the IRQF_ONESHOT flag
  mfd: twl4030-irq: Pass the IRQF_ONESHOT flag
  mfd: mt6397-core: Add GPIO sub-module support
  mfd: arizona: Add convience defines for micd_rate/micd_bias_starttime
  mfd: dt: Add bindings for DA9063 OnKey
  mfd: da9063: Add support for OnKey driver
  mfd: arizona: Fix incorrect Makefile conditionals
  mfd: arizona: Add stub for wm5102_patch()
  mfd: Check ACPI device companion before checking resources
  Documentation: Add WM8998/WM1814 device tree bindings
  mfd: arizona: Split INx_MODE into two fields
  mfd: wm5110: Add delay before releasing reset line
  mfd: arizona: Add better support for system suspend
  ...
2015-06-23 17:31:27 -07:00
Linus Torvalds
a57f14bac0 MMC core:
- Fix an error path in the mmc block layer
  - Fix PM domain attachment for the SDIO bus
  - Add support for driver strength selection
  - Increase a delay to let voltage stabilize
  - Add support for disabling write-protect detection
  - Add facility to support re-tuning
  - Re-tune and retry in the recovery path
  - Add reset option for SDIO
  - Consolidations and clean-ups
 
 MMC host:
  - Add Mediatek MMC driver
  - Constify platform_device_id for a couple of hosts
  - Fix modalias to make module auto-loading work for a couple of hosts
  - sdhci: Add support for sdhci-arasan4.9a
  - sdhci: Fix low memory corruption
  - sdhci: Restore behavior while creating OCR mask
  - sdhci: Add a callback to select drive strength
  - sdhci: Fix driver type B and D handling
  - sdhci: Add support for drive strength selection for SPT
  - sdhci: Enable HS400 for some Intel host controllers
  - sdhci: Convert to use the new re-tuning facility
  - sdhci: Various minor fixes and clean-ups
  - dw_mmc: Add support for hi6220
  - dw_mmc: Use core to handle absent write protect line
  - dw_mmc: Add support to switch voltage
  - tmio: Some fixes and modernizations
  - sh_mmcif: Improve clock rate calculation
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJVh+y8AAoJEP4mhCVzWIwp+fYQAIlZVzdLVCAgHHMKHlXeJ/Ib
 5Ltf7Vi6kO9WJUQc+/X0kicidNjeOiw8qvItYeZpVvZCuzMnBXLHGt99G0ACvagw
 hS/4GsI+keNbBLTlSriZVxMdjEbB4RIkC5TWsHuhcP16L6UmgDVil3Hqf6qasGU2
 cAr9lSUpe3uYlgyn7W5voolVWU2PNJq7Cy5E3y1052VbUsnhJZRvpsoCne++nG2O
 rJH9BQauVQ08VX3S6PcXYYDk2xe2rk7ExTiNw+tuMhjZkcd3dlKBRajoALpBqYFS
 nY3nSfMIVm1PmzpklrgF+7gUTdlihmi0ao1DsrFBHRISZ/ljb7yQ5Vma8Pg36NVK
 tdrZSBiOWhIXTgp+AIUSjuyv8S2wwsFozsmkVUNyA6XmfVmq2+lqz6rA7w+OIm7D
 iS9SBsAz1Iv6gpt388/Bb/yxULvYOVKECmORydu21yXxHT7eWTVfvQYHC9h40qhw
 oL86omRVFbeuouM1T867aFWKzaeA7hLXKbC4sWxdypyE2bPLraiC5izjlh4p3RzH
 UkQ4UUsym7b0UlL4lxKTUgRD8FuGK0ML+zeRsA1VgJmcCdzRaa2NFQfrX5aMVSgc
 iJ2zkHdxLCxkKTfcNn3k+B0PH3tMMn2cPIE7AhoVaIl79ACg9UB+/wG8f5pIifh5
 pPCWXFcaJ7gJkYpFDTnJ
 =ofUZ
 -----END PGP SIGNATURE-----

Merge tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmc

Pull MMC updates from Ulf Hansson:
 "Here are the changes for MMC for v4.2.

  MMC core:
   - Fix an error path in the mmc block layer
   - Fix PM domain attachment for the SDIO bus
   - Add support for driver strength selection
   - Increase a delay to let voltage stabilize
   - Add support for disabling write-protect detection
   - Add facility to support re-tuning
   - Re-tune and retry in the recovery path
   - Add reset option for SDIO
   - Consolidations and clean-ups

  MMC host:
   - Add Mediatek MMC driver
   - Constify platform_device_id for a couple of hosts
   - Fix modalias to make module auto-loading work for a couple of hosts
   - sdhci: Add support for sdhci-arasan4.9a
   - sdhci: Fix low memory corruption
   - sdhci: Restore behavior while creating OCR mask
   - sdhci: Add a callback to select drive strength
   - sdhci: Fix driver type B and D handling
   - sdhci: Add support for drive strength selection for SPT
   - sdhci: Enable HS400 for some Intel host controllers
   - sdhci: Convert to use the new re-tuning facility
   - sdhci: Various minor fixes and clean-ups
   - dw_mmc: Add support for hi6220
   - dw_mmc: Use core to handle absent write protect line
   - dw_mmc: Add support to switch voltage
   - tmio: Some fixes and modernizations
   - sh_mmcif: Improve clock rate calculation"

* tag 'mmc-v4.2' of git://git.linaro.org/people/ulf.hansson/mmc: (98 commits)
  mmc: queue: prevent soft lockups on PREEMPT=n
  mmc: mediatek: Add PM support for MMC driver
  mmc: mediatek: Add Mediatek MMC driver
  mmc: dt-bindings: add Mediatek MMC bindings
  mmc: card: Fixup request missing in mmc_blk_issue_rw_rq
  mmc: sdhci: fix low memory corruption
  mmc: sdhci-pci: Change AMD SDHCI quirk application scope
  i2c-piix4: Use Macro for AMD CZ SMBus device ID
  pci_ids: Add AMD KERNCZ device ID support
  mmc: queue: use swap() in mmc_queue_thread()
  mmc: dw_mmc: insmod followed by rmmod will hung for eMMC
  mmc: sdhci: Restore behavior while creating OCR mask
  mmc: sdhci-pxav3: fix device wakeup initialization
  mmc: core: Attach PM domain prior probing of SDIO func driver
  mmc: core: Remove redundant ->power_restore() callback for SD
  mmc: core: Remove redundant ->power_restore() callback for MMC
  mmc: sdhci-bcm2835: Actually enable the clock
  mmc: sdhci-bcm2835: Clean up platform allocations if sdhci init fails.
  mmc: sdhci-of-esdhc: enable interrupt mode to detect card
  mmc: sdhci-esdhc-imx: add quirk SDHCI_QUIRK2_BROKEN_HS200 for imx6qdl
  ...
2015-06-23 13:38:04 -07:00
Linus Torvalds
10b4b096d0 This is the big bulk of GPIO changes queued for the v4.2
kernel series:
 
 - A big set of cleanups to the aged sysfs interface from
   Johan Hovold. To get these in, v4.1-rc3 was merged into
   the tree as the first patch in that series had to go
   into stable. This makes the locking much more fine-grained
   (get rid of the "big GPIO lock(s)" and store states in the
   GPIO descriptors.
 
 - Rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value()
   to avoid confusions.
 
 - New drivers for:
   - NXP LPC18xx (currently LPC1850)
   - NetLogic XLP
   - Broadcom STB SoC's
   - Axis ETRAXFS
   - Zynq Ultrascale+ (subdriver)
 
 - ACPI:
   - Make it possible to retrieve GpioInt resources from
     a GPIO device using acpi_dev_gpio_irq_get()
   - Merge some dependent I2C changes exploiting this.
   - Support the ARM X-Gene GPIO standby driver.
 
 - Make it possible for the generic GPIO driver to read
   back the value set registers to reflect current
   status.
 
 - Loads of OMAP IRQ handling fixes.
 
 - Incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
   PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.
 
 - Janitorial (contification, checkpatch cleanups)
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABAgAGBQJVh76DAAoJEEEQszewGV1zYFsP/AnyCHs4M67k5Eegxtiwoomc
 OTqkVtOcob9kfqMkbZ1dsjZe2ZYIDiyWeQ1xuV+dD9nx/iAu6inUxb0dXhxKXonr
 +7mQglg32+zWTepLOJosoftoIqOb06lsMfgjL+tJcY5Od7/rewpdEplfEcjmq1O0
 0OdaV2FCXIhHDt52iYHT4tYI1GCky9K4Au9NlPCbKAsGneb3fQahF9o3JpYXl1Oq
 YhIFzUEhM+Zi2IoRsloGdK/eGEHni59IDekhZDf4PnYgA4Dkx2/e1A2Q0h5oT+QI
 j2yfRbI9t1gA5UK7JR/rVJF+5+E8uZ06TZgTo8tU00U4ZvppNgHt8O4KZkJMFBce
 KZzD9rkVVGp0NIDVwmOWjnfwkVVcQzMg/Wf17oM+qdaPO4GHEXNaQaInk1zmwqZq
 tQiTk47zA4rrEaYq3YZjt4xQjl8+ExDlOzFjnfLYAm27gbIl6EFWbX2ON981MC8g
 Nap8MLZINbGTlyDHtuqUlnqN+oXoP8niFuuDixYR+pM1P1bgwIVF+VopRJBFJRJP
 IeR6VdsI9KS99Kg8ICf4ds6WdKAGU3Htj+26udgMhIlOWrkCbvvexIxq9oBkwIB1
 VZofnSZLqnlKvo9Z140atvJWkFti7mqhItVjohmZyvyImLtmQBMq3kSGurXEqWms
 /NGZ0txPd1lMHx5o6ZPK
 =vKYs
 -----END PGP SIGNATURE-----

Merge tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio

Pull gpio updates from Linus Walleij:
 "This is the big bulk of GPIO changes queued for the v4.2 kernel
  series:

   - a big set of cleanups to the aged sysfs interface from Johan
     Hovold.  To get these in, v4.1-rc3 was merged into the tree as the
     first patch in that series had to go into stable.  This makes the
     locking much more fine-grained (get rid of the "big GPIO lock(s)"
     and store states in the GPIO descriptors.

   - rename gpiod_[g|s]et_array() to gpiod_[g|s]et_array_value() to
     avoid confusions.

   - New drivers for:
      * NXP LPC18xx (currently LPC1850)
      * NetLogic XLP
      * Broadcom STB SoC's
      * Axis ETRAXFS
      * Zynq Ultrascale+ (subdriver)

   - ACPI:
      * make it possible to retrieve GpioInt resources from a GPIO
        device using acpi_dev_gpio_irq_get()
      * merge some dependent I2C changes exploiting this.
      * support the ARM X-Gene GPIO standby driver.

   - make it possible for the generic GPIO driver to read back the value
     set registers to reflect current status.

   - loads of OMAP IRQ handling fixes.

   - incremental improvements to Kona, max732x, OMAP, MXC, RCAR,
     PCA953x, STP-XWAY, PCF857x, Crystalcove, TB10x.

   - janitorial (constification, checkpatch cleanups)"

* tag 'gpio-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (71 commits)
  gpio: Fix checkpatch.pl issues
  gpio: pcf857x: handle only enabled irqs
  gpio / ACPI: Return -EPROBE_DEFER if the gpiochip was not found
  GPIO / ACPI: export acpi_gpiochip_request(free)_interrupts for module use
  gpio: improve error reporting on own descriptors
  gpio: promote own request failure to pr_err()
  gpio: Added support to Zynq Ultrascale+ MPSoC
  gpio: add ETRAXFS GPIO driver
  fix documentation after renaming gpiod_set_array to gpiod_set_array_value
  gpio: Add GPIO support for Broadcom STB SoCs
  gpio: xgene: add ACPI support for APM X-Gene GPIO standby driver
  gpio: tb10x: Drop unneeded free_irq() call
  gpio: crystalcove: set IRQCHIP_SKIP_SET_WAKE for the irqchip
  gpio: stp-xway: Use the of_property_read_u32 helper
  gpio: pcf857x: Check for irq_set_irq_wake() failures
  gpio-stp-xway: Fix enabling the highest bit of the PHY LEDs
  gpio: Prevent an integer overflow in the pca953x driver
  gpio: omap: rework omap_gpio_irq_startup to handle current pin state properly
  gpio: omap: rework omap_gpio_request to touch only gpio specific registers
  gpio: omap: rework omap_x_irq_shutdown to touch only irqs specific registers
  ...
2015-06-23 13:34:02 -07:00
Silvan Wicki
a294aba164 i2c: busses: i2c-bcm2835: limits cdiv to allowed values
Checks if the cdiv value is in between min (0x2) and max (0xFFFE)
supported values by the bcm2835. If not, it returns -ENODEV.

See page 33/34 of BCM2835-ARM-Peripherals.pdf for the DIV register.
https://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf

Signed-off-by: Silvan Wicki <linux_wi@tinag.ch>
[wsa: resolved a merge conflict]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-23 19:55:19 +02:00
Wolfram Sang
365322fb32 i2c: sh_mobile: use proper type for timeout
wait_event_timeout returns long, not int.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-23 19:50:27 +02:00
Wolfram Sang
41bdbd2887 i2c: sh_mobile: use adapter default for timeout
5 seconds is a very large timeout, and it is hardcoded. Use the default
timeout from 'struct adapter' which is 1 second. It can also be modified
from userspace for specific workloads via i2c-dev.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-23 19:50:24 +02:00
Wolfram Sang
b6763d0da5 i2c: rcar: use proper type for timeout
wait_event_timeout returns long, not int.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-23 19:50:20 +02:00
Wolfram Sang
efd2c6118e i2c: rcar: use adapter default for timeout
5 seconds is a very large timeout, and it is hardcoded. Use the default
timeout from 'struct adapter' which is 1 second. It can also be modified
from userspace for specific workloads via i2c-dev.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-23 19:50:10 +02:00
Mika Westerberg
edfc390123 i2c: designware: Make sure the device is suspended before disabling runtime PM
The driver calls pm_runtime_put() right before pm_runtime_disable() in its
->remove() hook to make sure clock is gated etc. However, it turns out that
pm_runtime_put() only calls ->idle() hook without actually suspending
anything. The following pm_runtime_disable() will prevent the driver from
suspending thus leaving it "active".

It is better to suspend the device synchronously to make sure it is
actually suspended before disabling runtime PM from it.

While there, undo call to pm_runtime_use_autosuspend().

Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-21 21:30:35 +02:00
Wolfram Sang
3aaa34b992 i2c: tegra: apply size limit quirk
payload_size is a 12 bit field in the HW register, so add a limit for
this size. That way we gracefully reject the message beforehand instead
of generating an OOPS while transferring. Verified using some older
Tegra2 documentation and a more recent Jetson TK1 board.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
2015-06-21 21:24:10 +02:00
Wolfram Sang
4bb28e3776 i2c: tegra: don't advertise SMBUS_QUICK
This HW cannot send 0-byte-length messages and the driver discards them.
So, we should not advertise SMBUS_QUICK.

Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-21 21:16:26 +02:00
Nicholas Mc Guire
e8e523a42a i2c: octeon: remove unused signal handling
'commit 2637e5fd23 ("i2c: octeon: Fix i2c fail problem when a process is
terminated by a signal")' removed the wait_event_interruptible_timeout to
prevent half/mixed i2c messages from being sent/recievd but forgot to
drop the signal handling case in the return handling. This just removes
this dead code. While at it the return variable is adjusted to the type
expected.

Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-17 14:50:03 +02:00
Alexander Sverdlin
955fc95079 i2c: davinci: Optimize SCL generation
There are several cases where current clock configuration algorithm produces
not optimal results:
- truncation in "clk" calculation leads to the fact that actual BUS frequency
  will be always higher than spec except two exact module frequences 8MHz and
  12MHz in the whole 7-12MHz range of permitted frequences
- driver configures SCL HIGH to LOW ratio always 1 to 1 and this doesn't work
  well in 400kHz case, namely minimum time of LOW state (according to I2C Spec
  2.1) 1.3us will not be fulfilled. HIGH to LOW ratio 1 to 2 would be more
  approriate here.

Signed-off-by: Michael Lawnick <michael.lawnick@nokia.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-17 14:40:58 +02:00
Alexander Sverdlin
0a8237ae31 i2c: mux: pca954x: Use __i2c_transfer because of quirks
pca9541 and pca954x are calling master_xfer() of the parent adapter directly
thus bypassing the quirks checks of the adapter. Use __i2c_transfer() instead.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Łukasz Gemborowski <lukasz.gemborowski@nokia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Fixes: b7f6258402 ("i2c: add quirk checks to core")
2015-06-17 14:35:38 +02:00
Alexander Sverdlin
e766f338a7 i2c: mux: Use __i2c_transfer() instead of calling parent's master_xfer()
Newly introduced quirks infrastructure doesn't work for the devices behind
MUXes because MUX's master_xfer() calls parent's master_xfer() directly
without checking the quirks. Instead of duplicating check code in MUX just
call __i2c_transfer() instead. This has a side effect on tracing (messages
will appear on both MUX bus and parent bus), but maybe that's not bad at
the end.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Tested-by: Łukasz Gemborowski <lukasz.gemborowski@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Fixes: b7f6258402 ("i2c: add quirk checks to core")
2015-06-17 14:35:37 +02:00
Alexander Sverdlin
dc362d50ba i2c: use parent adapter quirks in mux
Inherit parent adapter quirks in MUX in case the devices on the multiplexed
buses are interested in the adapter limitations.

Signed-off-by: Łukasz Gemborowski <lukasz.gemborowski@nokia.com>
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org
Fixes: b7f6258402 ("i2c: add quirk checks to core")
2015-06-17 14:35:36 +02:00
Silvan Wicki
7b618638a5 i2c: bcm2835: clear reserved bits in S-Register
The datasheet mentions on page 31 that the bits 10-31 must be read as
don't care and written as 0.
https://www.raspberrypi.org/wp-content/uploads/2012/02/BCM2835-ARM-Peripherals.pdf

We cannot guarantee that we read bits 10-31 as always 0 (because the
datasheet says read as don't care). We clear the bits with a bitmask to
prevent writing back unknown data at the reserved bits.

Signed-off-by: Silvan Wicki <linux_wi@tinag.ch>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-17 14:35:09 +02:00
Wolfram Sang
3ded3743a0 i2c: sh_mobile: add errata workaround
This used to be in platform init code. We want it to do in the driver
now. This is basically a code move and a new compatible added.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-17 12:40:38 +02:00
Vincent Wan
bcb299947f i2c-piix4: Use Macro for AMD CZ SMBus device ID
Change AMD CZ SMBUS device ID from 0x790b to
use Macro definition

Signed-off-by: Wan ZongShun <Vincent.Wan@amd.com>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-16 08:58:06 +02:00
Javier Martinez Canillas
062476f24a mfd: cros_ec: Move protocol helpers out of the MFD driver
The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.

The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.

Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-15 13:18:20 +01:00
Javier Martinez Canillas
a841178445 mfd: cros_ec: Use a zero-length array for command data
Commit 1b84f2a4cd ("mfd: cros_ec: Use fixed size arrays to transfer
data with the EC") modified the struct cros_ec_command fields to not
use pointers for the input and output buffers and use fixed length
arrays instead.

This change was made because the cros_ec ioctl API uses that struct
cros_ec_command to allow user-space to send commands to the EC and
to get data from the EC. So using pointers made the API not 64-bit
safe. Unfortunately this approach was not flexible enough for all
the use-cases since there may be a need to send larger commands
on newer versions of the EC command protocol.

So to avoid to choose a constant length that it may be too big for
most commands and thus wasting memory and CPU cycles on copy from
and to user-space or having a size that is too small for some big
commands, use a zero-length array that is both 64-bit safe and
flexible. The same buffer is used for both output and input data
so the maximum of these values should be used to allocate it.

Suggested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-15 13:18:19 +01:00
Cyrille Pitchen
f30dc5208c i2c: at91: fix code checker warnings
buf_len is a size_t, so unsigned, but was tested with '<= 0'.

Reported-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-11 22:12:53 +09:00
Feng Kan
d845340394 i2c: busses: xgene-slimpro: fix incorrect __init declation for probe
Fix section mismatch error during kernel build for xgene_slimpro_i2c_probe
function. It was incorrectly defined with __init declaration.

Signed-off-by: Feng Kan <fkan@apm.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-10 22:17:34 +09:00
Alexander Sverdlin
41c8d45204 i2c: davinci: Avoid sending to own address
Sending a message to own address locks the controller up in very bizarre state,
it behaves as slave even if MDR register clearly states master. The controller
remains in this state until reset. To avoid unnecessary timeouts simply avoid
sending to own address. The controller cannot do this any way. Also, do not
enable AAS IRQ, as the slave mode is not supported by the driver and the only
possibility to trigger this IRQ is to send to own address.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-10 22:11:51 +09:00
Alexander Sverdlin
72a956c556 i2c: davinci: Refactor i2c_davinci_wait_bus_not_busy()
There are several problems in the function:
- "to_cnt" variable does nothing
- schedule_timeout() call without setting current state does nothing
- "allow_sleep" parameter is not really used

Refactor the function so that it really tries to wait. In case of timeout try
to recover the bus.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-10 22:08:36 +09:00
Kamal Dasu
dd1aa2524b i2c: brcmstb: Add Broadcom settop SoC i2c controller driver
Adding support for i2c controller driver for Broadcom settop
SoCs.

Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
[wsa: removed superfluous owner in platform_driver]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
2015-06-10 22:02:57 +09:00