As things currently stand, traditional EFI boot loaders and the EFI
boot stub are carrying essentially the same initialisation code
required to setup an EFI machine for booting a kernel. There's really
no need to have this code in two places and the hope is that, with
this new protocol, initialisation and booting of the kernel can be
left solely to the kernel's EFI boot stub. The responsibilities of the
boot loader then become,
o Loading the kernel image from boot media
File system code still needs to be carried by boot loaders for the
scenario where the kernel and initrd files reside on a file system
that the EFI firmware doesn't natively understand, such as ext4, etc.
o Providing a user interface
Boot loaders still need to display any menus/interfaces, for example
to allow the user to select from a list of kernels.
Bump the boot protocol number because we added the 'handover_offset'
field to indicate the location of the handover protocol entry point.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Acked-and-Tested-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1342689828-16815-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Release v1.3.82 wrapped a few lines of code in an "#ifdef
SAFE_RESET_DISK_CONTROLLER" and "#endif" pair. Since
SAFE_RESET_DISK_CONTROLLER was never defined anywhere that was basically
a verbose "#ifdef 0" and "#endif" pair. These dead lines have been in
the tree for sixteen years but now the time has come to remove them.
I guess the main lesson here is that if you want your dead code in the
tree for a very long time you'd better be creative. A plain old "#ifdef
0" and "#endif" pair just doesn't cut it!
See: http://lkml.kernel.org/r/199603301718.LAA00178@craie.inetnebr.com
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Link: http://lkml.kernel.org/r/1340230589.1773.7.camel@x61.thuisdomein
Acked-by: Jeff Epler <jepler@unpythonic.net>
Acked-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Some UEFI firmware will not load a .efi with a .reloc section
with a size of 0.
Therefore, we create a .efi image with 4 main areas and 3 sections.
1. PE/COFF file header
2. .setup section (covers all setup code following the first sector)
3. .reloc section (contains 1 dummy reloc entry, created in build.c)
4. .text section (covers the remaining kernel image)
To make room for the new .setup section data, the header
bugger_off_msg had to be shortened.
Reported-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Link: http://lkml.kernel.org/r/1339085121-12760-1-git-send-email-jordan.l.justen@intel.com
Tested-by: Lee G Rosenbaum <lee.g.rosenbaum@intel.com>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We need a way of printing useful messages to the user, for example
when we fail to open an initrd file, instead of just hanging the
machine without giving the user any indication of what went wrong. So
sprinkle some error messages throughout the EFI boot stub code to make
it easier for users to diagnose/report problems.
Reported-by: Keshav P R <the.ridikulus.rat@gmail.com>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1331907517-3985-3-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The loop at the 'close_handles' label in handle_ramdisks() should be
using 'i', which represents the number of initrd files that were
successfully opened, not 'nr_initrds' which is the number of initrd=
arguments passed on the command line.
Currently, if we execute the loop to close all file handles and we
failed to open any initrds we'll try to call the close function on a
garbage pointer, causing the machine to hang.
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1331907517-3985-2-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Pull x86 platform changes from Ingo Molnar:
"This tree includes assorted platform driver updates and a preparatory
series for a platform with custom DMA remapping semantics (sta2x11 I/O
hub)."
* 'x86-platform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/vsmp: Fix number of CPUs when vsmp is disabled
keyboard: Use BIOS Keyboard variable to set Numlock
x86/olpc/xo1/sci: Report RTC wakeup events
x86/olpc/xo1/sci: Produce wakeup events for buttons and switches
x86, platform: Initial support for sta2x11 I/O hub
x86: Introduce CONFIG_X86_DMA_REMAP
x86-32: Introduce CONFIG_X86_DEV_DMA_OPS
Pull x86 EFI updates from Ingo Molnar:
"This patchset makes changes to the bzImage EFI header, so that it can
be signed with a secure boot signature tool. It should not affect
anyone who is not using the EFI self-boot feature in any way."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Fix NumberOfRvaAndSizes field in PE32 header for EFI_STUB
x86, efi: Fix .text section overlapping image header for EFI_STUB
x86, efi: Fix issue of overlapping .reloc section for EFI_STUB
A new option is added to the relocs tool called '--realmode'.
This option causes the generation of 16-bit segment relocations
and 32-bit linear relocations for the real-mode code. When
the real-mode code is moved to the low-memory during kernel
initialization, these relocation entries can be used to
relocate the code properly.
In the assembly code 16-bit segment relocations must be relative
to the 'real_mode_seg' absolute symbol. Linear relocations must be
relative to a symbol prefixed with 'pa_'.
16-bit segment relocation is used to load cs:ip in 16-bit code.
Linear relocations are used in the 32-bit code for relocatable
data references. They are declared in the linker script of the
real-mode code.
The relocs tool is moved to arch/x86/tools/relocs.c, and added new
target archscripts that can be used to build scripts needed building
an architecture. be compiled before building the arch/x86 tree.
[ hpa: accelerating this because it detects invalid absolute
relocations, a serious bug in binutils 2.22.52.0.x which currently
produces bad kernels. ]
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/1336501366-28617-2-git-send-email-jarkko.sakkinen@intel.com
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
The PC BIOS does provide a NUMLOCK flag containing the desired state
of this LED. This patch sets the current state according to the data
in the bios.
[ hpa: fixed __weak declaration without definition, changed "inline"
to "static inline" ]
Signed-Off-By: Joshua Cov <joshuacov@googlemail.com>
Link: http://lkml.kernel.org/r/CAKL7Q7rvq87TNS1T_Km8fW_5OzS%2BSbYazLXKxW-6ztOxo3zorg@mail.gmail.com
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
sh_symtab is set but not used.
[ hpa: putting this in urgent because of the sheer harmlessness of the patch:
it quiets a build warning but does not change any generated code. ]
Signed-off-by: Kusanagi Kouichi <slash@ac.auone-net.jp>
Link: http://lkml.kernel.org/r/20120401082932.D5E066FC03D@msa105.auone-net.jp
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
The method used to work out whether we were booted by EFI firmware or
via a boot loader is broken. Because efi_main() is always executed
when booting from a boot loader we will dereference invalid pointers
either on the stack (CONFIG_X86_32) or contained in %rdx
(CONFIG_X86_64) when searching for an EFI System Table signature.
Instead of dereferencing these invalid system table pointers, add a
new entry point that is only used when booting from EFI firmware, when
we know the pointer arguments will be valid. With this change legacy
boot loaders will no longer execute efi_main(), but will instead skip
EFI stub initialisation completely.
[ hpa: Marking this for urgent/stable since it is a regression when
the option is enabled; without the option the patch has no effect ]
Signed-off-by: Matt Fleming <matt.hfleming@intel.com>
Link: http://lkml.kernel.org/r/1334584744.26997.14.camel@mfleming-mobl1.ger.corp.intel.com
Reported-by: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org> v3.3
Reason for merge:
The updates to the EFI boot stub generation conflicted with the
changes to properly use the get/put_unaligned_le*() macros to
generate images.
This merge commit completes the conversion in
arch/x86/boot/tools/build.c including the places in the code
which had been changed on the x86/efi branch.
Resolved Conflicts:
arch/x86/boot/tools/build.c
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We've actually got six data directories in the header, not one. Even
though the firmware loader doesn't seem to mind, when we come to sign
the kernel image the signing tool thinks that there is no Certificate
Table data directory, even though we've allocated space for one.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1332520506-6472-4-git-send-email-jordan.l.justen@intel.com
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This change modifes the PE .text section to start after
the first sector of the kernel image.
The header may be modified by the UEFI secure boot signing,
so it is not appropriate for it to be included in one of the
image sections. Since the sections are part of the secure
boot hash, this modification to the .text section contents
would invalidate the secure boot signed hash.
Note: UEFI secure boot does hash the image header, but
fields that are changed by the signing process are excluded
from the hash calculation. This exclusion process is only
handled for the image header, and not image sections.
Luckily, we can still easily boot without the first sector
by initializing a few fields in arch/x86/boot/compressed/eboot.c.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1332520506-6472-3-git-send-email-jordan.l.justen@intel.com
[jordan.l.justen@intel.com: set .text vma & file offset]
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Previously the .reloc section was embedded in the .text
section.
No relocations are required during the PE/COFF loading phase
for the kernel using the EFI_STUB UEFI loader. To fix the
issue of overlapping sections, create a .reloc section with a
zero length.
The .reloc section header must exist to make sure the image
will be loaded by the UEFI firmware, but a zero-length
section header seems to be sufficient.
Signed-off-by: Jordan Justen <jordan.l.justen@intel.com>
Link: http://lkml.kernel.org/r/1332520506-6472-2-git-send-email-jordan.l.justen@intel.com
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This is a partial revert of commit:
d40f833 "Restrict CFLAGS for hostprogs"
The endian-manipulation macros in tools/include need <linux/types.h>,
but the hostprogs in arch/x86/boot need several headers from the
kernel build tree, which means we have to add the kernel headers to
the include path. This picks up <linux/types.h> from the kernel tree,
which gives a warning.
Since this use of <linux/types.h> is intentional, add
-D__EXPORTED_HEADERS__ to the command line to silence the warning.
A better way to fix this would be to always install the exported
kernel headers into $(objtree)/usr/include as a standard part of the
kernel build, but that is a lot more involved.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1330436245-24875-5-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Pull x86 "urgent" leftovers from Ingo Molnar:
"Pending x86/urgent bits that were not high prio enough to warrant
-rc-less v3.3-final inclusion."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Fix pointer math issue in handle_ramdisks()
x86/ioapic: Add register level checks to detect bogus io-apic entries
x86, mce: Fix rcu splat in drain_mce_log_buffer()
x86, memblock: Move mem_hole_size() to .init
Pull trivial x86 branches from Ingo Molnar: small one-liners to fix up
details.
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Remove some noise from boot log when starting cpus
* 'x86-boot-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, boot: Fix port argument to inl() function
* 'x86-cpufeature-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, cpufeature: Add CPU features from Intel document 319433-012A
* 'x86-process-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86_64: Record stack pointer before task execution begins
* 'x86-uv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/UV: Lower UV rtc clocksource rating
"filename" is a efi_char16_t string so this check for reaching the end
of the array doesn't work. We need to cast the pointer to (u8 *) before
doing the math.
This patch changes the "filename" to "filename_16" to avoid confusion in
the future.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://lkml.kernel.org/r/20120305180614.GA26880@elgon.mountain
Acked-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
It would appear that we never actually generated a correct CRC when
building on a bigendian machine. Depending on the word size, we would
either generate an all-zero CRC (64-bit machine) or a byte-swapped
CRC (32-bit machine.) Fix the types used so we don't arbitrarily use
a 64-bit word to hold 32-bit numbers, and pass the CRC through
put_unaligned_le32() like all the other numbers.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Bowler <nbowler@elliptictech.com>
Link: http://lkml.kernel.org/r/20120229111322.9eb4b23ff1672e8853ad3b3b@canb.auug.org.au
We include <sys/sysmacros.h> and <asm/boot.h>, but none of those
header files actually provide anything this file needs. Furthermore,
it breaks cross-compilation, so just remove them.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: Matt Fleming <matt@console-pimps.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Bowler <nbowler@elliptictech.com>
Link: http://lkml.kernel.org/r/20120229111322.9eb4b23ff1672e8853ad3b3b@canb.auug.org.au
We may need to convert the endianness of the data we read from/write
to 'buf', so let's use {get,put}_unaligned_le32() to do that. Failure
to do so can result in accessing invalid memory, leading to a
segfault. Stephen Rothwell noticed this bug while cross-building an
x86_64 allmodconfig kernel on PowerPC.
We need to read from and write to 'buf' a byte at a time otherwise
it's possible we'll perform an unaligned access, which can lead to bus
errors when cross-building an x86 kernel on risc architectures.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Nick Bowler <nbowler@elliptictech.com>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1330436245-24875-6-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Currently tools/build has access to all the kernel headers in
$(srctree). This is unnecessary and could potentially allow
tools/build to erroneously include kernel headers when it should only
be including userspace-exported headers.
Unfortunately, mkcpustr still needs access to some of the asm kernel
headers, so explicitly special case that hostprog.
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1330436245-24875-5-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
"u32 port" in inl() should be "u16 port".
[ hpa: it's a bug, but it doesn't produce incorrect code, so no need
to put this into urgent or stable. ]
Signed-off-by: He Chunhui <hchunhui@mail.ustc.edu.cn>
Link: http://lkml.kernel.org/r/32892299.2931391328028508117.JavaMail.coremail@mailweb
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The efi boot stub tries to read the entire initrd in 1 go, however
some efi implementations hang if too much if asked to read too much
data at the same time. After some experimentation I found out that my
asrock p67 board will hang if asked to read chunks of 4MiB, so use a
safe value.
elilo reads in chunks of 16KiB, but since that requires many read
calls I use a value of 1 MiB. hpa suggested adding individual
blacklists for when systems are found where this value causes a crash.
Signed-off-by: Maarten Lankhorst <m.b.lankhorst@gmail.com>
Link: http://lkml.kernel.org/r/4EEB3A02.3090201@gmail.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
There is currently a large divide between kernel development and the
development of EFI boot loaders. The idea behind this patch is to give
the kernel developers full control over the EFI boot process. As
H. Peter Anvin put it,
"The 'kernel carries its own stub' approach been very successful in
dealing with BIOS, and would make a lot of sense to me for EFI as
well."
This patch introduces an EFI boot stub that allows an x86 bzImage to
be loaded and executed by EFI firmware. The bzImage appears to the
firmware as an EFI application. Luckily there are enough free bits
within the bzImage header so that it can masquerade as an EFI
application, thereby coercing the EFI firmware into loading it and
jumping to its entry point. The beauty of this masquerading approach
is that both BIOS and EFI boot loaders can still load and run the same
bzImage, thereby allowing a single kernel image to work in any boot
environment.
The EFI boot stub supports multiple initrds, but they must exist on
the same partition as the bzImage. Command-line arguments for the
kernel can be appended after the bzImage name when run from the EFI
shell, e.g.
Shell> bzImage console=ttyS0 root=/dev/sdb initrd=initrd.img
v7:
- Fix checkpatch warnings.
v6:
- Try to allocate initrd memory just below hdr->inird_addr_max.
v5:
- load_options_size is UTF-16, which needs dividing by 2 to convert
to the corresponding ASCII size.
v4:
- Don't read more than image->load_options_size
v3:
- Fix following warnings when compiling CONFIG_EFI_STUB=n
arch/x86/boot/tools/build.c: In function ‘main’:
arch/x86/boot/tools/build.c:138:24: warning: unused variable ‘pe_header’
arch/x86/boot/tools/build.c:138:15: warning: unused variable ‘file_sz’
- As reported by Matthew Garrett, some Apple machines have GOPs that
don't have hardware attached. We need to weed these out by
searching for ones that handle the PCIIO protocol.
- Don't allocate memory if no initrds are on cmdline
- Don't trust image->load_options_size
Maarten Lankhorst noted:
- Don't strip first argument when booted from efibootmgr
- Don't allocate too much memory for cmdline
- Don't update cmdline_size, the kernel considers it read-only
- Don't accept '\n' for initrd names
v2:
- File alignment was too large, was 8192 should be 512. Reported by
Maarten Lankhorst on LKML.
- Added UGA support for graphics
- Use VIDEO_TYPE_EFI instead of hard-coded number.
- Move linelength assignment until after we've assigned depth
- Dynamically fill out AddressOfEntryPoint in tools/build.c
- Don't use magic number for GDT/TSS stuff. Requested by Andi Kleen
- The bzImage may need to be relocated as it may have been loaded at
a high address address by the firmware. This was required to get my
macbook booting because the firmware loaded it at 0x7cxxxxxx, which
triggers this error in decompress_kernel(),
if (heap > ((-__PAGE_OFFSET-(128<<20)-1) & 0x7fffffff))
error("Destination address too large");
Cc: Mike Waychison <mikew@google.com>
Cc: Matthew Garrett <mjg@redhat.com>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1321383097.2657.9.camel@mfleming-mobl1.ger.corp.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
There are numerous broken references to Documentation files (in other
Documentation files, in comments, etc.). These broken references are
caused by typo's in the references, and by renames or removals of the
Documentation files. Some broken references are simply odd.
Fix these broken references, sometimes by dropping the irrelevant text
they were part of.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This has been obsoleted by the root= commandline and the rdev utility
for many, many years. People who still depend on this will surely
have a copy of the rdev utility around, the rest of the world gets rid
of another piece of buildhost-dependent data in the build. Thanks to
Paul Bolle for the build.c cleanup.
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Link: http://lkml.kernel.org/r/1302607824-24699-1-git-send-email-mmarek@suse.cz
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
When we use BIOS function e801 to probe memory, we should use ax/bx
(or cx/dx) as a pair, not mix and match. This was a typo during the
translation from assembly code, and breaks at least one set of
machines in the field (which return cx = dx = 0).
Reported-and-tested-by: Chris Samuel <chris@csamuel.org>
Fix-proposed-by: Thomas Meyer <thomas@m3y3r.de>
Link: http://lkml.kernel.org/r/1303566747.12067.10.camel@localhost.localdomain
Ensure build doesn't silently continue despite read failure,
addressing a warning due to the unchecked call.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
LKML-Reference: <AANLkTimxxTMU3=4ry-_zbY6v1xiDi+hW9y1RegTr8vLK@mail.gmail.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This integrates the XZ decompression code to the x86 pre-boot code.
mkpiggy.c is updated to reserve about 32 KiB more buffer safety margin for
kernel decompression. It is done unconditionally for all decompressors to
keep the code simpler.
The XZ decompressor needs around 30 KiB of heap, so the heap size is
increased to 32 KiB on both x86-32 and x86-64.
Documentation/x86/boot.txt is updated to list the XZ magic number.
With the x86 BCJ filter in XZ, XZ-compressed x86 kernel tends to be a few
percent smaller than the equivalent LZMA-compressed kernel.
Signed-off-by: Lasse Collin <lasse.collin@tukaani.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Alain Knaff <alain@knaff.lu>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Cc: Phillip Lougher <phillip@lougher.demon.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix included-by file reference comments
x86, cpu: Only CPU features determine NX capabilities
x86, cpu: Call verify_cpu during 32bit CPU startup
x86, cpu: Clear XD_DISABLED flag on Intel to regain NX
x86, cpu: Rename verify_cpu_64.S to verify_cpu.S
A relocatable kernel can be anywhere in lowmem -- and in the case of a
kdump kernel, is likely to be fairly high. Since the early page
tables map everything from address zero up we need to make sure we
allocate enough brk that we can map all of lowmem if we need to.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Tested-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4D0AD3ED.8070607@kernel.org>
The code is 32bit already, and can be used in 32bit routines.
Signed-off-by: Kees Cook <kees.cook@canonical.com>
LKML-Reference: <1289414154-7829-2-git-send-email-kees.cook@canonical.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The kernel decompression code parses the ELF header and then copies
the segment to the corresponding destination. Currently it uses slow
byte-copy code. This patch makes it use the string copy operations
instead.
In the test the copy performance can be improved very significantly after using
the string copy operation mechanism.
1. The copy time can be reduced from 150ms to 20ms on one Atom machine
2. The copy time can be reduced about 80% on another machine
The time is reduced from 7ms to 1.5ms when using 32-bit kernel.
The time is reduced from 10ms to 2ms when using 64-bit kernel.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
LKML-Reference: <1286502453-7043-1-git-send-email-yakui.zhao@intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
earlyprintk can take and I/O port, so we need to handle this case in
the setup code too, otherwise 0x3f8 will be treated as a baud rate.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C7B05A6.4010801@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Torsten reported that there is garbage output,
after commit 8fee13a48e (x86,
setup: enable early console output from the decompressor)
It turns out we missed the offset for that case.
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C7B0578.8090807@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
It is a subset of <ctype.h> functionality, so name it ctype.h. Also,
reorganize header files so #include statements are clustered near the
top as they should be.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <4C5752F2.8030206@kernel.org>
This enables the decompressor output to be seen on the serial console.
Most of the code is shared with the regular boot code.
We could add printf to the decompressor if needed, but currently there
is no sufficiently compelling user.
-v2: define BOOT_BOOT_H to avoid include boot.h
-v3: early_serial_base need to be static in misc.c ?
-v4: create seperate string.c printf.c cmdline.c early_serial_console.c
after hpa's patch that allow global variables in compressed/misc stage
-v5: remove printf.c related
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Separate early_serial_console from tty.c
This allows for reuse of
early_serial_console.c/string.c/printf.c/cmdline.c in boot/compressed/.
-v2: according to hpa, don't include string.c etc
-v3: compressed/misc.c must have early_serial_base as static, so move it back to tty.c
for setup code
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C568D2B.205@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In order for global variables and functions to work in the
decompressor, we need to fix up the GOT in assembly code.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <4C57382E.8050501@zytor.com>
putchar is using early_serial_base to check if port is initialized.
So we only assign it after early_serial_init() is called,
in case we need use VGA to debug early serial console.
Also add display for port addr and baud.
-v2: update to current tip
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C3E0171.6050008@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Make the boot code also accept the console=uart8250,io,0x2f8,115200n
form of early console.
Also add back simple_guess_base(), otherwise those simple_strtoull(,,0)
are not going to work.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <4C3CCE05.4090505@kernel.org>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
This patch adds serial I/O support to the real-mode setup (very early
boot) printf(). It's useful for debugging boot code when running Linux
under KVM, for example. The actual code was lifted from early printk.
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
LKML-Reference: <1278835617-11368-1-git-send-email-penberg@cs.helsinki.fi>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Catch missing conversion to the register structure "glove box" scheme.
Found by gcc 4.6's new warnings.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <20100610111040.F1781B1A2B@basil.firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-35' of git://repo.or.cz/linux-kbuild: (81 commits)
kbuild: Revert part of e8d400a to resolve a conflict
kbuild: Fix checking of scm-identifier variable
gconfig: add support to show hidden options that have prompts
menuconfig: add support to show hidden options which have prompts
gconfig: remove show_debug option
gconfig: remove dbg_print_ptype() and dbg_print_stype()
kconfig: fix zconfdump()
kconfig: some small fixes
add random binaries to .gitignore
kbuild: Include gen_initramfs_list.sh and the file list in the .d file
kconfig: recalc symbol value before showing search results
.gitignore: ignore *.lzo files
headerdep: perlcritic warning
scripts/Makefile.lib: Align the output of LZO
kbuild: Generate modules.builtin in make modules_install
Revert "kbuild: specify absolute paths for cscope"
kbuild: Do not unnecessarily regenerate modules.builtin
headers_install: use local file handles
headers_check: fix perl warnings
export_report: fix perl warnings
...
This reverts commit b3b77c8cae, which was
also totally broken (see commit 0d2daf5cc8 that reverted the crc32
version of it). As reported by Stephen Rothwell, it causes problems on
big-endian machines:
> In file included from fs/jfs/jfs_types.h:33,
> from fs/jfs/jfs_incore.h:26,
> from fs/jfs/file.c:22:
> fs/jfs/endian24.h:36:101: warning: "__LITTLE_ENDIAN" is not defined
The kernel has never had that crazy "__BYTE_ORDER == __LITTLE_ENDIAN"
model. It's not how we do things, and it isn't how we _should_ do
things. So don't go there.
Requested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linux does not define __BYTE_ORDER in its endian header files which makes
some header files bend backwards to get at the current endian. Lets
#define __BYTE_ORDER in big_endian.h/litte_endian.h to make it easier for
header files that are used in user space too.
In userspace the convention is that
1. _both_ __LITTLE_ENDIAN and __BIG_ENDIAN are defined,
2. you have to test for e.g. __BYTE_ORDER == __BIG_ENDIAN.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-setup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, setup: Don't skip mode setting for the standard VGA modes
x86-64, setup: Inhibit decompressor output if video info is invalid
x86, setup: When restoring the screen, update boot_params.screen_info
The code for setting standard VGA modes probes for the current mode,
and skips the mode setting if the mode is 3 (color text 80x25) or 7
(mono text 80x25). Unfortunately, there are BIOSes, including the
VMware BIOS, which report the previous mode if function 0F is queried
while the screen is in a VESA mode, and of course, nothing can help a
mode poked directly into the hardware.
As such, the safe option is to set the mode anyway, and only query to
see if we should be using mode 7 rather than mode 3. People who don't
want any mode setting at all should probably use vga=0x0f04
(VIDEO_CURRENT_MODE). It's possible that should be the kernel
default.
Reported-by Rene Arends <R.R.Arends@hro.nl>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <tip-*@git.kernel.org>
Inhibit output from the kernel decompressor if the video information
is invalid. This was already the case for 32 bits, make 64 bits
match.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <tip-*@git.kernel.org>
When we restore the screen content after a mode change, we return the
cursor to its former position. However, we need to also update
boot_params.screen_info accordingly, so that the decompression code
knows where on the screen the cursor is. Just in case the video BIOS
does something extra screwy, read the cursor position back from the
BIOS instead of relying on it doing the right thing.
While we're at it, make sure we cap the cursor position to the new
screen coordinates.
Reported-by: Wim Osterholt <wim@djo.tudelft.nl>
Bugzilla-Reference: http://bugzilla.kernel.org/show_bug.cgi?id=15329
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Frans Pop <elendil@planet.nl>
Cc: Avi Kivity <avi@redhat.com>
Cc: x86@kernel.org
LKML-Reference: <1265478443-31072-10-git-send-email-elendil@planet.nl>
[ Left out the KVM bits. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Iomem has no special significance on x86. Use the standard mem*
functions instead of trying to call other versions. Some fixups
are needed to match the function prototypes.
Signed-off-by: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1265380629-3212-6-git-send-email-brgerst@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The necessary changes to the x86 Kconfig and boot/compressed to allow the
use of this new compression method
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recently, some distros have started shipping versions of gcc which
default to -march=i686. This breaks building kernels for pre-i686
machines, even if they have been selected in Kconfig, due to the
generation of CMOV instructions.
There isn't enough benefit to try to preserve the generation of these
instructions even when selected, so simply force -march=i386 for the
decompressor when building a 32-bit kernel.
Reported-and-tested-by: Chris Rankin <rankincj@yahoo.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <219280.97558.qm@web52907.mail.re2.yahoo.com>
* 'for-33' of git://repo.or.cz/linux-kbuild: (29 commits)
net: fix for utsrelease.h moving to generated
gen_init_cpio: fixed fwrite warning
kbuild: fix make clean after mismerge
kbuild: generate modules.builtin
genksyms: properly consider EXPORT_UNUSED_SYMBOL{,_GPL}()
score: add asm/asm-offsets.h wrapper
unifdef: update to upstream revision 1.190
kbuild: specify absolute paths for cscope
kbuild: create include/generated in silentoldconfig
scripts/package: deb-pkg: use fakeroot if available
scripts/package: add KBUILD_PKG_ROOTCMD variable
scripts/package: tar-pkg: use tar --owner=root
Kbuild: clean up marker
net: add net_tstamp.h to headers_install
kbuild: move utsrelease.h to include/generated
kbuild: move autoconf.h to include/generated
drop explicit include of autoconf.h
kbuild: move compile.h to include/generated
kbuild: drop include/asm
kbuild: do not check for include/asm-$ARCH
...
Fixed non-conflicting clean merge of modpost.c as per comments from
Stephen Rothwell (modpost.c had grown an include of linux/autoconf.h
that needed to be changed to generated/autoconf.h)
This adds a new category of symbols to the relocs program: symbols
which are known to be relative, even though the linker emits them as
absolute; this is the case for symbols that live in the linker script,
which currently applies to _end.
Unfortunately the previous workaround of putting _end in its own empty
section was defeated by newer binutils, which remove empty sections
completely.
This patch also changes the symbol matching to use regular expressions
instead of hardcoded C for specific patterns.
This is a decidedly non-minimal patch: a modified version of the
relocs program is used as part of the Syslinux build, and this is
basically a backport to Linux of some of those changes; they have
thus been well tested.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <4AF86211.3070103@zytor.com>
Acked-by: Michal Marek <mmarek@suse.cz>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
* 'x86-setup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
vgacon: Add support for setting the default cursor state
vc: Add support for hiding the cursor when creating VTs
x86, setup: Store the boot cursor state
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (36 commits)
x86, mm: Correct the implementation of is_untracked_pat_range()
x86/pat: Trivial: don't create debugfs for memtype if pat is disabled
x86, mtrr: Fix sorting of mtrr after subtracting
x86: Move find_smp_config() earlier and avoid bootmem usage
x86, platform: Change is_untracked_pat_range() to bool; cleanup init
x86: Change is_ISA_range() into an inline function
x86, mm: is_untracked_pat_range() takes a normal semiclosed range
x86, mm: Call is_untracked_pat_range() rather than is_ISA_range()
x86: UV SGI: Don't track GRU space in PAT
x86: SGI UV: Fix BAU initialization
x86, numa: Use near(er) online node instead of roundrobin for NUMA
x86, numa, bootmem: Only free bootmem on NUMA failure path
x86: Change crash kernel to reserve via reserve_early()
x86: Eliminate redundant/contradicting cache line size config options
x86: When cleaning MTRRs, do not fold WP into UC
x86: remove "extern" from function prototypes in <asm/proto.h>
x86, mm: Report state of NX protections during boot
x86, mm: Clean up and simplify NX enablement
x86, pageattr: Make set_memory_(x|nx) aware of NX support
x86, sleep: Always save the value of EFER
...
Fix up conflicts (added both iommu_shutdown and is_untracked_pat_range)
to 'struct x86_platform_ops') in
arch/x86/include/asm/x86_init.h
arch/x86/kernel/x86_init.c
Rather than having X86_L1_CACHE_BYTES and X86_L1_CACHE_SHIFT
(with inconsistent defaults), just having the latter suffices as
the former can be easily calculated from it.
To be consistent, also change X86_INTERNODE_CACHE_BYTES to
X86_INTERNODE_CACHE_SHIFT, and set it to 7 (128 bytes) for NUMA
to account for last level cache line size (which here matters
more than L1 cache line size).
Finally, make sure the default value for X86_L1_CACHE_SHIFT,
when X86_GENERIC is selected, is being seen before that for the
individual CPU model options (other than on x86-64, where
GENERIC_CPU is part of the choice construct, X86_GENERIC is a
separate option on ix86).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Ravikiran Thirumalai <kiran@scalex86.org>
Acked-by: Nick Piggin <npiggin@suse.de>
LKML-Reference: <4AFD5710020000780001F8F0@vpn.id2.novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a field to store the boot cursor state and implement this for VGA on
x86. This can then be used to set the default policy for the boot console.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
LKML-Reference: <1258142222-16092-1-git-send-email-mjg@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
A single 'movl' is shorter than the 'xorl'-'orl' pair.
No change in behaviour.
Signed-off-by: Alexander Potashev <aspotashev@gmail.com>
LKML-Reference: <1256341043-4928-1-git-send-email-aspotashev@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Older binutils breaks if ASSERT() is used without a sink
for the output.
For example 2.14.90.0.6 is known to be broken, the link
fails with:
LD .tmp_vmlinux1
ld:arch/x86/kernel/vmlinux.lds:678: parse error
Document this quirk in all three files that use it.
See: http://marc.info/?l=linux-kbuild&m=124930110427870&w=2
See[2]: d2ba8b2 ("x86: Fix assert syntax in vmlinux.lds.S")
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Roland McGrath <roland@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <4AD6523D.5030909@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Remove redundant non-NUMA topology functions
x86: early_printk: Protect against using the same device twice
x86: Reduce verbosity of "PAT enabled" kernel message
x86: Reduce verbosity of "TSC is reliable" message
x86: mce: Use safer ways to access MCE registers
x86: mce, inject: Use real inject-msg in raise_local
x86: mce: Fix thermal throttling message storm
x86: mce: Clean up thermal throttling state tracking code
x86: split NX setup into separate file to limit unstack-protected code
xen: check EFER for NX before setting up GDT mapping
x86: Cleanup linker script using new linker script macros.
x86: Use section .data.page_aligned for the idt_table.
x86: convert to use __HEAD and HEAD_TEXT macros.
x86: convert compressed loader to use __HEAD and HEAD_TEXT macros.
x86: fix fragile computation of vsyscall address
Replace the use of CROSS_COMPILE to select a customized
installkernel script with the possibility to set INSTALLKERNEL
to select a custom installkernel script when running make:
make INSTALLKERNEL=arm-installkernel install
With this patch we are now more consistent across
different architectures - they did not all support use
of CROSS_COMPILE.
The use of CROSS_COMPILE was a hack as this really belongs
to gcc/binutils and the installkernel script does not change
just because we change toolchain.
The use of CROSS_COMPILE caused troubles with an upcoming patch
that saves CROSS_COMPILE when a kernel is built - it would no
longer be installable.
[Thanks to Peter Z. for this hint]
This patch undos what Ian did in commit:
0f8e2d62fa
("use ${CROSS_COMPILE}installkernel in arch/*/boot/install.sh")
The patch has been lightly tested on x86 only - but all changes
looks obvious.
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Mike Frysinger <vapier@gentoo.org> [blackfin]
Acked-by: Russell King <linux@arm.linux.org.uk> [arm]
Acked-by: Paul Mundt <lethal@linux-sh.org> [sh]
Acked-by: "H. Peter Anvin" <hpa@zytor.com> [x86]
Cc: Ian Campbell <icampbell@arcom.com>
Cc: Tony Luck <tony.luck@intel.com> [ia64]
Cc: Fenghua Yu <fenghua.yu@intel.com> [ia64]
Cc: Hirokazu Takata <takata@linux-m32r.org> [m32r]
Cc: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Cc: Kyle McMartin <kyle@mcmartin.ca> [parisc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> [powerpc]
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390]
Cc: Thomas Gleixner <tglx@linutronix.de> [x86]
Cc: Ingo Molnar <mingo@redhat.com> [x86]
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This has the consequence of changing the section name use for head
code from ".text.head" to ".head.text".
Linus suggested that we merge the ".text.head" section with ".text"
(presumably while preserving the fact that the head code starts at 0).
When I tried this it caused the kernel to not boot.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The absence of vmlinux.lds here keeps .vmlinux.lds.cmd from being
included, which in turn leads to it and all its dependents always
getting rebuilt independent of whether they are already up-to-date.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
LKML-Reference: <4A8D84670200007800010D31@vpn.id2.novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Some intcall() misuses the input biosregs as output in
cf06de7b9c
This fixes the problem vga=ask boot option doesn't show enough modes.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
LKML-Reference: <20090701021307.GA3127@localhost.localdomain>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
There were a set of pre-Kconfig configuration variables defined in the
video code. There is absolutely no evidence that they have been
tweaked by anybody in modern history, so just get rid of them and hope
nobody notices. If someone does complain, these should be made real
Kconfig variables.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (45 commits)
x86, mce: fix error path in mce_create_device()
x86: use zalloc_cpumask_var for mce_dev_initialized
x86: fix duplicated sysfs attribute
x86: de-assembler-ize asm/desc.h
i386: fix/simplify espfix stack switching, move it into assembly
i386: fix return to 16-bit stack from NMI handler
x86, ioapic: Don't call disconnect_bsp_APIC if no APIC present
x86: Remove duplicated #include's
x86: msr.h linux/types.h is only required for __KERNEL__
x86: nmi: Add Intel processor 0x6f4 to NMI perfctr1 workaround
x86, mce: mce_intel.c needs <asm/apic.h>
x86: apic/io_apic.c: dmar_msi_type should be static
x86, io_apic.c: Work around compiler warning
x86: mce: Don't touch THERMAL_APIC_VECTOR if no active APIC present
x86: mce: Handle banks == 0 case in K7 quirk
x86, boot: use .code16gcc instead of .code16
x86: correct the conversion of EFI memory types
x86: cap iomem_resource to addressable physical memory
x86, mce: rename _64.c files which are no longer 64-bit-specific
x86, mce: mce.h cleanup
...
Manually fix up trivial conflict in arch/x86/mm/fault.c
Enable gcov profiling of the entire kernel on x86_64. Required changes
include disabling profiling for:
* arch/kernel/acpi/realmode and arch/kernel/boot/compressed:
not linked to main kernel
* arch/vdso, arch/kernel/vsyscall_64 and arch/kernel/hpet:
profiling causes segfaults during boot (incompatible context)
Signed-off-by: Peter Oberparleiter <oberpar@linux.vnet.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Li Wei <W.Li@Sun.COM>
Cc: Michael Ellerman <michaele@au1.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Heiko Carstens <heicars2@linux.vnet.ibm.com>
Cc: Martin Schwidefsky <mschwid2@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use .code16gcc to compile arch/x86/boot/bioscall.S rather than
.code16, since some older versions of binutils can't generate 32-bit
addressing expressions (67 prefixes) in .code16 mode, only in
.code16gcc mode.
Reported-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-kbuild-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (46 commits)
x86, boot: add new generated files to the appropriate .gitignore files
x86, boot: correct the calculation of ZO_INIT_SIZE
x86-64: align __PHYSICAL_START, remove __KERNEL_ALIGN
x86, boot: correct sanity checks in boot/compressed/misc.c
x86: add extension fields for bootloader type and version
x86, defconfig: update kernel position parameters
x86, defconfig: update to current, no material changes
x86: make CONFIG_RELOCATABLE the default
x86: default CONFIG_PHYSICAL_START and CONFIG_PHYSICAL_ALIGN to 16 MB
x86: document new bzImage fields
x86, boot: make kernel_alignment adjustable; new bzImage fields
x86, boot: remove dead code from boot/compressed/head_*.S
x86, boot: use LOAD_PHYSICAL_ADDR on 64 bits
x86, boot: make symbols from the main vmlinux available
x86, boot: determine compressed code offset at compile time
x86, boot: use appropriate rep string for move and clear
x86, boot: zero EFLAGS on 32 bits
x86, boot: set up the decompression stack as early as possible
x86, boot: straighten out ranges to copy/zero in compressed/head*.S
x86, boot: stylistic cleanups for boot/compressed/head_64.S
...
Fixed trivial conflict in arch/x86/configs/x86_64_defconfig manually
git status complains of untracked (generated) files in arch/x86/boot..
# Untracked files:
# (use "git add <file>..." to include in what will be committed)
#
# ../../arch/x86/boot/compressed/mkpiggy
# ../../arch/x86/boot/compressed/piggy.S
# ../../arch/x86/boot/compressed/vmlinux.lds
# ../../arch/x86/boot/voffset.h
# ../../arch/x86/boot/zoffset.h
..so adjust .gitignore files accordingly.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
For relocatable 32bit kernels, boot/compressed/relocs.c processes
relocation entries in the kernel image and appends it to the kernel
image such that boot/compressed/head_32.S can relocate the kernel.
The kernel image is one statically linked object and only uses two
relocation types - R_386_PC32 and R_386_32, of the two only the latter
needs massaging during kernel relocation and thus handled by relocs.
R_386_PC32 is ignored and all other relocation types are considered
error.
When the target of a relocation resides in a discarded section,
binutils doesn't throw away the relocation record but nullifies it by
changing it to R_386_NONE, which unfortunately makes relocs fail.
The problem was triggered by yet out-of-tree x86 stack unwind patches
but given the binutils behavior, ignoring R_386_NONE is the right
thing to do.
The problem has been tracked down to binutils behavior by Jan Beulich.
[ Impact: fix build with certain binutils by ignoring R_386_NONE ]
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jan Beulich <JBeulich@novell.com>
Cc: Ingo Molnar <mingo@elte.hu>
LKML-Reference: <4A1B8150.40702@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remove ACPI 3 E820 extended memory attributes support. At least one
vendor actively set all the flags to zero, but left ECX on return at
24. This bug may be present in other BIOSes.
The breakage functionally means the ACPI 3 flags are probably
completely useless, and that no OS any time soon is going to rely on
their existence. Therefore, drop support completely. We may want to
revisit this question in the future, if we find ourselves actually
needing the flags.
This reverts all or part of the following checkins:
cd670599b7c549e71d07
However, retain the part from the latter commit that copies e820 into
a temporary buffer; that is an unrelated BIOS workaround. Put in a
comment to explain that part.
See https://bugzilla.redhat.com/show_bug.cgi?id=499396 for some
additional information.
[ Impact: detect all memory on affected machines ]
Reported-by: Thomas J. Baker <tjb@unh.edu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Len Brown <len.brown@intel.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Cc: Kyle McMartin <kmcmartin@redhat.com>
Cc: Matt Domsch <matt_domsch@dell.com>
Correct the calculation of ZO_INIT_SIZE (the amount of memory we need
during decompression). One symbol (ZO_startup_32) was missing from
zoffset.h, and another (ZO_z_extract_offset) was misspelled.
[ Impact: build fix ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
arch/x86/boot/compressed/misc.c contains several sanity checks on the
output address. Correct constraints that are no longer correct:
- the alignment test should be MIN_KERNEL_ALIGN on both 32 and 64
bits.
- the 64 bit maximum address was set to 2^40, which was the limit of
one specific x86-64 implementation. Change the test to 2^46, the
current Linux limit, and at least try to test the end rather than
the beginning.
- for non-relocatable kernels, test against LOAD_PHYSICAL_ADDR on both
32 and 64 bits.
[ Impact: fix potential boot failure due to invalid tests ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
A long ago, in days of yore, it all began with a god named Thor.
There were vikings and boats and some plans for a Linux kernel
header. Unfortunately, a single 8-bit field was used for bootloader
type and version. This has generally worked without *too* much pain,
but we're getting close to flat running out of ID fields.
Add extension fields for both type and version. The type will be
extended if it the old field is 0xE; the version is a simple MSB
extension.
Keep /proc/sys/kernel/bootloader_type containing
(type << 4) + (ver & 0xf) for backwards compatiblity, but also add
/proc/sys/kernel/bootloader_version which contains the full version
number.
[ Impact: new feature to support more bootloaders ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Make the kernel_alignment field adjustable; this allows us to set it
to a large value (intended to be 16 MB to avoid ZONE_DMA contention,
memory holes and other weirdness) while a smart bootloader can still
force a loading at a lesser alignment if absolutely necessary.
Also export pref_address (preferred loading address, corresponding to
the link-time address) and init_size, the total amount of linear
memory the kernel will require during initialization.
[ Impact: allows better kernel placement, gives bootloader more info ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remove a couple of lines of dead code from
arch/x86/boot/compressed/head_*.S; all of these update registers that
are dead in the current code.
[ Impact: cleanup ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Use LOAD_PHYSICAL_ADDR instead of CONFIG_PHYSICAL_START in the 64-bit
decompression code, for equivalence with the 32-bit code.
[ Impact: cleanup, increases code similarity ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Make symbols from the main vmlinux, as opposed to just
compressed/vmlinux, available to header.S. Also, export a few
additional symbols.
This will be used in a subsequent patch to export the total memory
footprint of the kernel.
[ Impact: enable future enhancement ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Determine the compressed code offset (from the kernel runtime address)
at compile time. This allows some minor optimizations in
arch/x86/boot/compressed/head_*.S, but more importantly it makes this
value available to the build process, which will enable a future patch
to export the necessary linear memory footprint into the bzImage
header.
[ Impact: cleanup, future patch enabling ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
In the pre-decompression code, use the appropriate largest possible
rep movs and rep stos to move code and clear bss, respectively. For
reverse copy, do note that the initial values are supposed to be the
address of the first (highest) copy datum, not one byte beyond the end
of the buffer.
rep strings are not necessarily the fastest way to perform these
operations on all current processors, but are likely to be in the
future, and perhaps more importantly, we want to encourage the
architecturally right thing to do here.
This also fixes a couple of trivial inefficiencies on 64 bits.
[ Impact: trivial performance enhancement, increase code similarity ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The 64-bit code already clears EFLAGS as soon as it has a stack. This
seems like a reasonable precaution, so do it on 32 bits as well.
[ Impact: extra paranoia ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Set up the decompression stack as soon as we know where it needs to
go. That way we have a full-service stack as soon as possible, rather
than relying on the BP_scratch field.
Note that the stack does need to be empty during bss zeroing (or
else the stack needs to be moved out of the bss segment, which is also
an option.)
[ Impact: cleanup, minor paranoia ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Both on 32 and 64 bits, we copy all the way up to the end of bss,
except that on 64 bits there is a hack to avoid copying on top of the
page tables. There is no point in copying bss at all, especially
since we are just about to zero it all anyway.
To clean up and unify the handling, we now do:
- copy from startup_32 to _bss.
- zero from _bss to _ebss.
- the _ebss symbol is aligned to an 8-byte boundary.
- the page tables are moved to a separate section.
Use _bss as the copy endpoint since _edata may be misaligned.
[ Impact: cleanup, trivial performance improvement ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Clean up style issues in arch/x86/boot/compressed/head_64.S. This
file had a lot fewer style issues than its 32-bit cousin, but the ones
it has are worth fixing, especially since it makes the two files more
similar.
[ Impact: cleanup, no object code change ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reformat arch/x86/boot/compressed/head_32.S to be closer to currently
preferred kernel assembly style, that is:
- opcode and operand separated by tab
- operands separated by ", "
- C-style comments
This also makes it more similar to head_64.S.
[ Impact: cleanup, no object code change ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
When generating the compression suffix in
arch/x86/boot/compressed/Makefile, follow standard Kbuild
conventions, that is:
- Use a dash not underscore before y/m/n endings
- Use := whenever possible.
Requested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Simplify the arch/x86/boot/compressed/Makefile, by using the new
capability of specifying multiple inputs to a compressor, and the
CONFIG_X86_NEED_RELOCS Kconfig symbol.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Aligning the .bss section makes it trivial to use large operation
sizes for moving the initialized sections and clearing the .bss.
The alignment chosen (L1 cache) is somewhat arbitrary, but should be
large enough to avoid all known performance traps and small enough to
not cause troubles.
[ Impact: trivial performance enhancement, future patch prep ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Look at the:
diff -u arch/x86/boot/compressed/vmlinux_*.lds
output and realize that they're basially exactly the same except for
trivial naming differences, and the fact that the 64-bit version has a
"pgtable" thing.
So unify them.
There's some trivial cleanup there (make the output format a Kconfig thing
rather than doing #ifdef's for it, and unify both 32-bit and 64-bit BSS
end to "_ebss", where 32-bit used to use the traditional "_end"), but
other than that it's really very mindless and straigt conversion.
For example, I think we should aim to remove "startup_32" vs "startup_64",
and just call it "startup", and get rid of one more difference. I didn't
do that.
Also, notice the comment in the unified vmlinux.lds.S talks about
"head_64" and "startup_32" which is an odd and incorrect mix, but that was
actually what the old 64-bit only lds file had, so the confusion isn't
new, and now that mixing is arguably more accurate thanks to the
vmlinux.lds.S file being shared between the two cases ;)
[ Impact: cleanup, unification ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: Comment change only
The glove box is about avoiding problems with *registers* being
touched, not *memory*.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: BIOS proofing
"Glove box" off BIOS interrupts in the video code.
LKML-Reference: <49DE7F79.4030106@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Impact: BIOS proofing
"Glove box" off BIOS interrupts in the MCA code.
LKML-Reference: <49DE7F79.4030106@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Impact: BIOS proofing
"Glove box" off BIOS interrupts in the EDD code.
LKML-Reference: <49DE7F79.4030106@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: BIOS proofing
"Glove box" off BIOS interrupts in the APM code.
LKML-Reference: <49DE7F79.4030106@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Impact: BIOS proofing
"Glove box" off BIOS interrupts in the core boot code.
LKML-Reference: <49DE7F79.4030106@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: new interfaces (not yet used)
For all the platforms out there, there is an infinite number of buggy
BIOSes. This adds infrastructure to treat BIOS interrupts more like
toxic waste and "glove box" them -- we switch out the register set,
perform the BIOS interrupt, and then restore the previous state.
LKML-Reference: <49DE7F79.4030106@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Impact: Fixes these modes on at least one system
The rewrite of the setup code into C resequenced the font setting and
register reprogramming phases of configuring nonstandard VGA modes
which use 480 scan lines in text mode. However, there exists at least
one board (Micro-Star MS-7383 version 2.0) on which this resequencing
causes an unusable display.
Revert to the original sequencing: set up 480-line mode, install the
font, and then adjust the vertical end register appropriately.
This failure was masked by the fact that the 480-line setup was broken
until checkin 5f64135612 (therefore this
is not a -stable candidate bug fix.)
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: code size reduction (possibly critical)
The x86 boot and decompression code has no use of the branch profiling
constructs, so disable them. This would bloat the setup code by as
much as 14K, eating up a fairly large chunk of the 32K area we are
guaranteed to have.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: BIOS bug safety
For pre-ACPI 3 BIOSes, pre-initialize the end of the e820 buffer just
in case the BIOS returns an unchanged %ecx but without actually
touching the ACPI 3 extended flags field.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: ACPI 3 spec compliance, BIOS bug workaround
The ACPI 3 spec added another field to the E820 buffer -- which is
backwards incompatible, since it contains a validity bit.
Furthermore, there has been at least one report of a BIOS which
assumes that the buffer it is pointed at is the same buffer as for the
previous E820 call. Therefore, read the data into a temporary buffer
and copy the standard part of it if and only if the valid bit is set.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: BIOS bugproofing
Since there are BIOSes known to clobber %ebx and %esi for INT 15 E820,
assume there is something out there clobbering %edi and/or %ebp too,
and don't wait for it to fail.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Jordan Hargrave diagnosed a BIOS clobbering %esi in the E820 call.
That particular BIOS has been fixed, but there is a possibility that
this is responsible for other occasional reports of early boot
failure, and it does not hurt to add %esi to the clobbers.
-stable candidate patch.
Cc: Justin Forbes <jmforbes@linuxtx.org>
Signed-off-by: Michael K Johnson <johnsonm@rpath.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
Impact: fix rarely-used feature
The VGA Miscellaneous Output Register is read from address 0x3CC but
written to address 0x3C2. This was missed when this code was
converted from assembly to C. While we're at it, clean up the code by
making the overflow bits and the math used to set the bits explicit.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: cleanup
The setup code is mostly 16-bit code, but there is a small stub of
32-bit code at the end. Move the 32-bit code to a separate segment,
.text32, to avoid scrambling the disassembly.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: cleanup
Instead of using CLEAN_FILES in arch/x86/Makefile, add generated files
to targets in arch/x86/boot/Makefile, so they will get naturally
cleaned up by "make clean".
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: cleanup
Remove targets that were used for zImage only, and Makefile
infrastructure that was there to support the zImage/bzImage split.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
LKML-Reference: <1236879901.24144.26.camel@test.thuisdomein>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: obsolete feature removal
The zImage kernel format has been functionally unused for a very long
time. It is just barely possible to build a modern kernel that still
fits within the zImage size limit, but it is highly unlikely that
anyone ever uses it. Furthermore, although it is still supported by
most bootloaders, it has been at best poorly tested (or not tested at
all); some bootloaders are even known to not support zImage at all and
not having even noticed.
Also remove some really obsolete constants that no longer have any
meaning.
LKML-Reference: <49B703D4.1000008@zytor.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: remove unused/broken code
The Voyager subarch last built successfully on the v2.6.26 kernel
and has been stale since then and does not build on the v2.6.27,
v2.6.28 and v2.6.29-rc5 kernels.
No actual users beyond the maintainer reported this breakage.
Patches were sent and most of the fixes were accepted but the
discussion around how to do a few remaining issues cleanly
fizzled out with no resolution and the code remained broken.
In the v2.6.30 x86 tree development cycle 32-bit subarch support
has been reworked and removed - and the Voyager code, beyond the
build problems already known, needs serious and significant
changes and probably a rewrite to support it.
CONFIG_X86_VOYAGER has been marked BROKEN then. The maintainer has
been notified but no patches have been sent so far to fix it.
While all other subarchs have been converted to the new scheme,
voyager is still broken. We'd prefer to receive patches which
clean up the current situation in a constructive way, but even in
case of removal there is no obstacle to add that support back
after the issues have been sorted out in a mutually acceptable
fashion.
So remove this inactive code for now.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clenaup
Linker script will put startup_32 at predefined
address so using startup_32 will not bloat the
code size.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: clenaup
Linker script will put startup_32 at predefined
address so using ENTRY will not bloat the code
size.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup
We are in setup stage so we use GLOBAL
instead of ENTRY and do not increase code
size.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In general, the only definitions that assembly files can use
are in _types.S headers (where available), so convert them.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
When probing the keyboard controller to enable A20, if we get FF back
(which is *possible* as a valid status word, but is extremely
unlikely) then bail after much fewer iterations than we otherwise
would, and abort the attempt to access the KBC.
This hopefully should make it work a lot better for embedded platforms
which don't have a KBC and where the BIOS doesn't implement
INT 15h AX=2401h (and doesn't boot with A20 already enabled.)
If this works, it will be the one remaining use of CONFIG_X86_ELAN as
anything other than a processor type optimization option.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: fix potential miscompile (currently believed non-manifest)
As the comment explains, the VBE DDC call can clobber any register.
Tell the compiler about that fact.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix potential miscompile (currently believed non-manifest)
As the comment explains, the VBE DDC call can clobber any register.
Tell the compiler about that fact.
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Impact: Replaces x86 kernel decompressor with new code
This is the third part of the bzip2/lzma patch
The bzip patch is based on an idea by Christian Ludwig, includes support for
compressing the kernel with bzip2 or lzma rather than gzip. Both
compressors give smaller sizes than gzip. Lzma's decompresses faster
than bzip2.
It also supports ramdisks and initramfs' compressed using these two
compressors.
The functionality has been successfully used for a couple of years by
the udpcast project
This version applies to "tip" kernel 2.6.28
This part contains:
- support for new bzip2 and lzma kernel compression for x86
Signed-off-by: Alain Knaff <alain@knaff.lu>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: build fix with certain compilers
GCC can decide to use %dil when "r" is used, which is not valid for
setnz.
This bug was brought out by Stephen Rothwell's merging of the
branch tracer into linux-next.
[ Thanks to Uros Bizjak for recommending 'q' over 'Q' ]
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: make global variables static
Fix these sparse warnings:
arch/x86/boot/video.c:233:3: warning: symbol 'saved' was not declared. Should it be static?
arch/x86/boot/video-vga.c:37:13: warning: symbol 'video_vga' was not declared. Should it be static?
Signed-off-by: Hannes Eder <hannes@hanneseder.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: fix section mismatch warning - apic_x2apic_phys
x86: fix section mismatch warning - apic_x2apic_cluster
x86: fix section mismatch warning - apic_x2apic_uv_x
x86: fix section mismatch warning - apic_physflat
x86: fix section mismatch warning - apic_flat
x86: memtest fix use of reserve_early()
x86 syscall.h: fix argument order
x86/tlb_uv: remove strange mc146818rtc include
x86: remove redundant KERN_DEBUG on pr_debug
x86: do_boot_cpu - check if we have ESR register
x86: MAINTAINERS change for AMD microcode patch loader
x86/proc: fix /proc/cpuinfo cpu offline bug
x86: call dmi-quirks for HP Laptops after early-quirks are executed
x86, kexec: fix hang on i386 when panic occurs while console_sem is held
MCE: Don't run 32bit machine checks with interrupts on
x86: SB600: skip IRQ0 override if it is not routed to INT2 of IOAPIC
x86: make variables static
Change header guards named "ASM_X86__*" to "_ASM_X86_*" since:
a. the double underscore is ugly and pointless.
b. no leading underscore violates namespace constraints.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
These variables are only used in their source files, so make them static.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently, it is possible to set a graphics VESA mode at boot time via the
vga= parameter even when no framebuffer driver supporting this is
configured. This could lead to the system booting with a black screen,
without a usable console.
Fix this problem by only allowing to set graphics modes at boot time if a
supporting framebuffer driver is configured.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace a magic number with a named constant in the VESA boot code.
Signed-off-by: Michal Januszewski <spock@gentoo.org>
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After commit 968de4f ("i386: Relocatable kernel support") IMAGE_OFFSET wasn't
actually used anymore in the (current) X86 build system. Now remove its last
traces.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: segfault on build of a 32-bit relocatable kernel
When converting arch/x86/boot/compressed/relocs.c to support unlimited
sections, the computation of sym_strtab in walk_relocs() was done
incorrectly. This causes a segfault for some people when building the
relocatable 32-bit kernel.
Pointed out by Anonymous <pageexec@freemail.hu>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Some BIOSes do not indicate error when trying to read from non-
existing device. Zero buffer before reading and check that we
possibly have valid MBR by looking for MBR magic.
This was fixed in different way for edd.S in
http://marc.info/?l=linux-kernel&m=114087765422490&w=2, but lost
again when edd.S was rewritten in C.
Signed-off-by: Andrey Borzenkov < arvidjaar@mail.ru>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Checkin e38e05a858 added a 9th CPU flag
word, but didn't adjust the boot code to match. This patch adds the
necessary boot code support.
Note: due to a typo in an #if statement, it didn't trigger the #error
this was supposed to do.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Impact: None (cleanup)
SWAP_DEV is unused since 2.6.23-rc1. The comment was already incorrect
since (at least) 2.6.12.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
> This is regression but old enough. Apparently I had for whatever reasons
> EDD turned off till recently. This is 2.6.27-rc5 just in case.
>
> In 2006 I fixed ghost devices due to buggy BIOS:
>
> http://marc.info/?l=linux-kernel&m=114087765422490&w=2
>
> Later edd.S has been rewritten in C, and apparently this patch has been
> lost:
>
> {pts/1}% ls /sys/firmware/edd
> int13_dev80/ int13_dev84/ int13_dev88/ int13_dev8c/
> int13_dev81/ int13_dev85/ int13_dev89/ int13_dev8d/
> int13_dev82/ int13_dev86/ int13_dev8a/ int13_dev8e/
> int13_dev83/ int13_dev87/ int13_dev8b/ int13_dev8f/
>
> But I have just a single disk. This is the same system BTW.
Some BIOSes do not always set CF on error before return from int13.
The patch adds additional check for status being zero (AH == 0).
This was fixed for edd.S in
http://marc.info/?l=linux-kernel&m=114087765422490&w=2, but lost
again when edd.S was rewritten in C.
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When building image.iso (make isoimage), use the isohybrid tool if it
exists. isohybrid is a script included with Syslinux 3.72 and higher,
which creates an image that can be booted either as a hard disk
(including removable, e.g. USB disk) or as a CD-ROM.
If isohybrid doesn't exist, then this has no effect.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The CPU feature detection code in the boot code is somewhat minimal,
and doesn't include all possible CPUID words. In particular, it
doesn't contain the code for CPU feature words 2 (Transmeta),
3 (Linux-specific), 5 (VIA), or 7 (scattered). Zero them out, so we
can still set those bits as known at compile time; in particular, this
allows creating a Linux-specific NOPL flag and have it required (and
therefore resolvable at compile time) in 64-bit mode.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The Kbuild variable "targets" is supposed to be
configuration-independent and reflect "all possible targets". This is
required to make "make clean" work properly.
Therefore, move all manipulation of "targets" as well as custom rules
out of the x86-32 ifdef statement. Only leave inside the ifdefs the
things that are genuinely configuration-dependent.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We have had a number of cases where <asm/cpufeature.h> (and its
predecessors) have diverged substantially from the names list in
/proc/cpuinfo. This patch generates the latter from the former.
It retains the option for explicitly overriding the strings, but by
making that require a separate action it should at least be less
likely to happen.
It would be good to do a future pass and rename strings that are
gratuituously different in the kernel (/proc/cpuinfo is a userspace
interface and must remain constant.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The CPU feature detection code in the boot code is somewhat minimal,
and doesn't include all possible CPUID words. In particular, it
doesn't contain the code for CPU feature words 2 (Transmeta),
3 (Linux-specific), 5 (VIA), or 7 (scattered). Zero them out, so we
can still set those bits as known at compile time; in particular, this
allows creating a Linux-specific NOPL flag and have it required (and
therefore resolvable at compile time) in 64-bit mode.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This recent patch
commit c3965bd151
Author: Paul Jackson <pj@sgi.com>
Date: Wed May 14 08:15:34 2008 -0700
x86 boot: proper use of ARRAY_SIZE instead of repeated E820MAX constant
caused these new warnings during a normal build:
In file included from linux-2.6/arch/x86/boot/memory.c:17:
linux-2.6/include/linux/log2.h: In function '__ilog2_u32':
linux-2.6/include/linux/log2.h:34: warning: implicit declaration of function 'fls'
linux-2.6/include/linux/log2.h: In function '__ilog2_u64':
linux-2.6/include/linux/log2.h:42: warning: implicit declaration of function 'fls64'
linux-2.6/include/linux/log2.h: In function '__roundup_pow_of_two ':
linux-2.6/include/linux/log2.h:63: warning: implicit declaration of function 'fls_long'
I tried to fix them in log2.h, but it's difficult because the real mode
environment is completely different from a normal kernel environment. Instead
define an own ARRAY_SIZE macro in boot.h, similar to the other private
macros there.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Clean up the code for crashes during SpeedStep probing on older
machines.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
yesterday I tried to reactivate my old 486 box and wanted to install a
current Linux with latest kernel on it. But it turned out that the
latest kernel does not boot because the machine crashes early in the
setup code.
After some debugging it turned out that the problem is the query_ist()
function. If this interrupt with that function is called the machine
simply locks up. It looks like a BIOS bug. Looking for a workaround for
this problem I wrote the attached patch. It checks for the CPUID
instruction and if it is not implemented it does not call the speedstep
BIOS function. As far as I know speedstep should be available since some
Pentium earliest.
Alan Cox observed that it's available since the Pentium II, so cpuid
levels 4 and 5 can be excluded altogether.
H. Peter Anvin cleaned up the code some more:
> Right in concept, but I dislike the implementation (duplication of the
> CPU detect code we already have). Could you try this patch and see if
> it works for you?
which, with a small modification to fix a build error with it the
resulting kernel boots on my machine.
Signed-off-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Comments in arch/x86/boot/compressed/head_32.S erroneously refer to the
real mode pointer as the second and the heap area as the third argument
to decompress_kernel(). In fact, these have been the first and second
argument, respectively, since v2.6.20.
This patch corrects the comments. It introduces no code changes.
Signed-off-by: Philipp Kohlbecher <xt28@gmx.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Inflate requires some dynamic memory allocation very early in the boot
process and this is provided with a set of four functions:
malloc/free/gzip_mark/gzip_release.
The old inflate code used a mark/release strategy rather than implement
free. This new version instead keeps a count on the number of outstanding
allocations and when it hits zero, it resets the malloc arena.
This allows removing all the mark and release implementations and unifying
all the malloc/free implementations.
The architecture-dependent code must define two addresses:
- free_mem_ptr, the address of the beginning of the area in which
allocations should be made
- free_mem_end_ptr, the address of the end of the area in which
allocations should be made. If set to 0, then no check is made on
the number of allocations, it just grows as much as needed
The architecture-dependent code can also provide an arch_decomp_wdog()
function call. This function will be called several times during the
decompression process, and allow to notify the watchdog that the system is
still running. If an architecture provides such a call, then it must
define ARCH_HAS_DECOMP_WDOG so that the generic inflate code calls
arch_decomp_wdog().
Work initially done by Matt Mackall, updated to a recent version of the
kernel and improved by me.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch consolidates the header guard names which are also used
externally, i.e. in .c files.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Without checking the return value of get_edd_info() and adding the
entry only in the success case, 6 devices show up under
/sys/firmware/edd/, no matter how many devices are actually present.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Merge the GDT_ENTRY() macro between arch/x86/boot/pm.c and
arch/x86/kernel/acpi/sleep.c and put the new one in
<asm-x86/segment.h>.
While we're at it, correct the bitmasks for the limit and flags. The
new version relies on using ULL constants in order to cause type
promotion rather than explicit casts; this avoids having to include
<linux/types.h> in <asm-x86/segments.h>.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch allows the disabling of decompression messages during
x86 bootup.
Signed-off-by: Ben Collins <ben.collins@canonical.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jeremy Fitzhardinge wrote:
>
> Maybe it really does require the far jump immediately after setting PE
> in cr0...
>
> Hm, I don't remember this paragraph being in vol 3a, section 8.9.1
> before. Is it a recent addition?
>
> Random failures can occur if other instructions exist between steps
> 3 and 4 above. Failures will be readily seen in some situations,
> such as when instructions that reference memory are inserted between
> steps 3 and 4 while in system management mode.
>
I don't remember that, either.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: build failure in maximal configurations
The 32-bit x86 relocatable kernel requires an auxilliary host program
to process the relocations. This program had a hard-coded arbitrary
limit of a 100 ELF sections. Instead of a hard-coded limit, allocate
the structures dynamically.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Apparently, DOS and possibly other legacy operating systems issued a
null command to the keyboard controller after toggling A20,
specifically "pulse output pins" with no output pins specified. This
was presumably done for synchronization reasons. This has made it
into at least the UHCI spec, and it has been found to cause
compatibility problems when "legacy USB" is enabled (which it almost
always is) to not have this byte sent.
It is *NOT* clear if any of these compatibility problems has any
effect on Linux. However, for maximum compatibility, issue this null
command after togging A20 through the KBC.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
... so it could fall back to normal numa and we'd reduce the impact of the
NUMAQ subarch.
NUMAQ depends on GENERICARCH
also decouple genericarch numa from acpi.
also make it fall back to bigsmp if apicid > 8.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch lets the early real mode code look for the 'quiet' option
on the kernel command line and pass a loadflag to the decompressor.
When this flag is set, we suppress the "Decompressing Linux... Parsing
ELF... done." messages.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Replace hardcoded offsets embedded in macros in
arch/x86/boot/compressed with proper structure references.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Trying to boot a 64-bit kernel on a 32bit Pentium 4 gets
you an amusing message along the lines of.
"you need an x86-64, but you only have an i1586"
due to the P4 being family F. Munge it to be 686.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch is motivated by a subsequent patch which will allow for more
memory map entries on EFI supported systems than can be passed via the x86
legacy BIOS E820 interface. The legacy interface is limited to E820MAX ==
128 memory entries, and that "E820MAX" manifest constant was used as the
size for several arrays and loops over those arrays.
The primary change in this patch is to change code loop sizes over those
arrays from using the constant E820MAX, to using the ARRAY_SIZE() macro
evaluated for the array being looped. That way, a subsequent patch can
change the size of some of these arrays, without breaking this code.
This patch also adds a parameter to the sanitize_e820_map() routine,
which had an implicit size for the array passed it of E820MAX entries.
This new parameter explicitly passes the size of said array. Once again,
this will allow a subsequent patch to change that array size for some
calls to sanitize_e820_map() without breaking the code.
As part of enhancing the sanitize_e820_map() interface this way, I further
combined the unnecessarily distinct x86_32 and x86_64 declarations for
this routine into a single, commonly used, declaration.
This patch in itself should make no difference to the resulting kernel
binary.
[ mingo@elte.hu: merged to -tip ]
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Just moved an open brace to the previous line.
Signed-off-by: Miklos Vajna <vmiklos@frugalware.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We should better use already defined flags from processor-flags.h instead
of defining own ones
[>>> object code check >>>]
original
md5sum: 129f24be6df396fb7d8bf998c01fc716 arch/x86/boot/compressed/head_64.o
text data bss dec hex filename
705 48 45056 45809 b2f1 arch/x86/boot/compressed/head_64.o
patched
md5sum: 129f24be6df396fb7d8bf998c01fc716 arch/x86/boot/compressed/head_64-new.o
text data bss dec hex filename
705 48 45056 45809 b2f1 arch/x86/boot/compressed/head_64-new.o
[<<< object code check <<<]
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add a kernel parameter option to 'edd' to enable/disable BIOS Enhanced Disk
Drive Services. CONFIG_EDD_OFF disables EDD while still compiling EDD into
the kernel. Default behavior can be forced using 'edd=on' or 'edd=off' as
a kernel parameter.
[akpm@linux-foundation.org: fix kernel-parameters.txt]
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds a field of 64-bit physical pointer to NULL terminated
single linked list of struct setup_data to real-mode kernel
header. This is used as a more extensible boot parameters passing
mechanism.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add some autogenerated files to various .gitignore files
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
cleanup: change the _end in compressed vmlinux_64.lds.
also change _heap to _ebss that is not needed.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The kernel decompressor wrapper uses memory located beyond the
end of the image. This might lead to hard to debug problems,
but even if it can be proven to be safe, it is at the very
least unclean. I don't see any advantages either, unless you
count it not being zeroed out as an advantage. This patch
moves the boot-heap area to the bss segment.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove old comments that include the old arch/i386 directory.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move wakeup code to .c, so that video mode setting code can be shared
between boot and wakeup. Remove nasty assembly code in 64-bit case by
re-using trampoline code. Stack setup was fixed to clear high 16bits
of %esp, maybe that fixes some machines.
.c code sharing and morse code was done H. Peter Anvin, Sam Ravnborg
reviewed kbuild related stuff, and it seems okay to him. Rafael did
some cleanups.
[rjw:
* Made the patch stop breaking compilation on x86-32
* Added arch/x86/kernel/acpi/sleep.h
* Got rid of compiler warnings in arch/x86/kernel/acpi/sleep.c
* Fixed 32-bit compilation on x86-64 systems
* Added include/asm-x86/trampoline.h and fixed the non-SMP
compilation on 64-bit x86
* Removed arch/x86/kernel/acpi/sleep_32.c which was not used
* Fixed some breakage caused by the integration of smpboot.c done
under us in the meantime]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In arch/x86/boot/compressed/misc.c, the variable vidmem is
the only variable that ends up in de data segment. It's also
superfluous, because the first thing the code does is:
if (RM_SCREEN_INFO.orig_video_mode == 7) {
vidmem = (char *) 0xb0000;
vidport = 0x3b4;
} else {
vidmem = (char *) 0xb8000;
vidport = 0x3d4;
}
This patch removes the initialisation.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Also update field names to simply payload_{offset,length} so as to not rule
out uncompressed images.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: virtualization@lists.linux-foundation.org
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The new x86 setup code (4fd06960f1) broke booting on an old P3/500MHz
with an onboard Voodoo3 of mine. After debugging it, it turned out
to be caused by the fact that the vesa probing now asks for VBE2 data.
Disassembing the video BIOS shows that it overflows the vesa_general_info
structure when VBE2 data is requested because the source addresses for the
information strings which get strcpy'ed to the buffer lie outside the 32K
BIOS code (and hence contain long sequences of 0xff's).
E.G.:
get_vbe_controller_info:
00002A9C 60 pushaw
00002A9D 1E push ds
00002A9E 0E push cs
00002A9F 1F pop ds
00002AA0 2BC9 sub cx,cx
00002AA2 6626813D56424532 cmp dword [es:di],0x32454256 ; "VBE2"
00002AAA 7501 jnz .1
00002AAC 41 inc cx
.1:
00002AAD 51 push cx
00002AAE B91400 mov cx,0x14
00002AB1 BED47F mov si, controller_header
00002AB4 57 push di
00002AB5 F3A4 rep movsb ; copy vbe1.2 header
00002AB7 B9EC00 mov cx,0xec
00002ABA 2AC0 sub al,al
00002ABC F3AA rep stosb ; zero pad remainder
00002ABE 5F pop di
00002ABF E8EB0D call word get_memory
00002AC2 C1E002 shl ax,0x2
00002AC5 26894512 mov [es:di+0x12],ax ; total memory
00002AC9 26C745040003 mov word [es:di+0x4],0x300 ; VBE version
00002ACF 268C4D08 mov [es:di+0x8],cs
00002AD3 268C4D10 mov [es:di+0x10],cs
00002AD7 59 pop cx
00002AD8 E361 jcxz .done ; VBE2 requested?
00002ADA 8D9D0001 lea bx,[di+0x100]
00002ADE 53 push bx
00002ADF 87DF xchg bx,di ; di now points to 2nd half
00002AE1 26C747140001 mov word [es:bx+0x14],0x100 ; sw rev
00002AE7 26897F06 mov [es:bx+0x6],di ; oem string
00002AEB 268C4708 mov [es:bx+0x8],es
00002AEF BE5280 mov si,0x8052 ; oem string
00002AF2 E87A1B call word strcpy
00002AF5 26897F0E mov [es:bx+0xe],di ; video mode list
00002AF9 268C4710 mov [es:bx+0x10],es
00002AFD B91E00 mov cx,0x1e
00002B00 BEE87F mov si,vidmodes
00002B03 F3A5 rep movsw
00002B05 26897F16 mov [es:bx+0x16],di ; oem vendor
00002B09 268C4718 mov [es:bx+0x18],es
00002B0D BE2480 mov si,0x8024 ; oem vendor
00002B10 E85C1B call word strcpy
00002B13 26897F1A mov [es:bx+0x1a],di ; oem product
00002B17 268C471C mov [es:bx+0x1c],es
00002B1B BE3880 mov si,0x8038 ; oem product
00002B1E E84E1B call word strcpy
00002B21 26897F1E mov [es:bx+0x1e],di ; oem product rev
00002B25 268C4720 mov [es:bx+0x20],es
00002B29 BE4580 mov si,0x8045 ; oem product rev
00002B2C E8401B call word strcpy
00002B2F 58 pop ax
00002B30 B90001 mov cx,0x100
00002B33 2BCF sub cx,di
00002B35 03C8 add cx,ax
00002B37 2AC0 sub al,al
00002B39 F3AA rep stosb ; zero pad
.done:
00002B3B 1F pop ds
00002B3C 61 popaw
00002B3D B84F00 mov ax,0x4f
00002B40 C3 ret
(The full BIOS can be found at http://peter.korsgaard.com/vgabios.bin
if interested).
The old setup code didn't ask for VBE2 info, and the new code doesn't
actually do anything with the extra information, so the fix is to simply
not request it. Other BIOS'es might have the same problem.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The proper way to terminate the e820 chain is with %ebx == 0 on the
last legitimate memory block. However, several BIOSes don't do that
and instead return error (CF = 1) when trying to read off the end of
the list. For this error return, %eax doesn't necessarily return the
SMAP signature -- correctly so, since %ah should contain an error code
in this case.
To deal with some particularly broken BIOSes, we clear the entire e820
chain if the SMAP signature is missing in the middle, indicating a
plain insane e820 implementation. However, we need to make the test
for CF = 1 before the SMAP check.
This fixes at least one HP laptop (nc6400) for which none of the
memory-probing methods (e820, e801, 88) functioned fully according to
spec.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In arch/x86/boot/printf.c gets rid of unused tail of digits: const char
*digits = "0123456789abcdefghijklmnopqrstuvwxyz"; (we are using 0-9a-f
only)
Uses smaller/faster lowercasing (by ORing with 0x20)
if we know that we work on numbers/digits. Makes
strtoul smaller, and also we are getting rid of
static const char small_digits[] = "0123456789abcdefx";
static const char large_digits[] = "0123456789ABCDEFX";
since this works equally well:
static const char digits[16] = "0123456789ABCDEF";
Size savings:
$ size vmlinux.org vmlinux
text data bss dec hex filename
877320 112252 90112 1079684 107984 vmlinux.org
877048 112252 90112 1079412 107874 vmlinux
It may be also a tiny bit faster because code has less
branches now, but I doubt it is measurable.
[ hugh@veritas.com: uppercase pointers fix ]
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Instead of obscure numbers, print the list of missing CPU features in
cleartext. To conserve space, use a host program (mkcpustr.c) to
produce a compact list of mandatory features only.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Do this rather than defining a global version and overriding it in
almost all cases in order to make subsequent patches simpler.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
for bzImage, the vmlinux_64.lds still have s32 bit code, and startup_32
should be 0. fix the comment.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remainder of unification can occur inplace.
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
There seems to be a preference for the 64 bit version so use that on 32 bit and
drop the stray leading "."
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The files are now identical so merge them.
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
vmlinux_64 and vmlinux_32.scr are now identical
size shows an expected movement from .text to .rodata and 4 extra bytes
of padding.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
size reports no change in arch/x86/boot/compressed/vmlinux.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The GDT_ENTRY() macro in pm.c would incorrectly cut the bottom 8 bits
off the base. We didn't define any bases with the bottom 8 bits
nonzero, so it is a non-manifest bug, but it's still a bug.
Pointed out by John Smith <johnsmith9344@gmail.com>.
Cc: John Smith <johnsmith9344@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If we use the bootloader-provided stack pointer, we might end up in a
situation where the bootloader (incorrectly) pointed the stack in the
middle of our heap. Catch this by simply comparing the computed heap
end value to the stack pointer minus the defined stack size.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Push video mode setup as late as possible; messages issued through the
BIOS interface after video mode setup will either not be seen (for
framebuffer modes) or will screw up the cursor (for text modes.)
In particular, this makes the EDD probing message show up correctly.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tell the user to specify edd=off in the case of EDD probing hangs.
Per LKML discussion.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add prototype for cmdline_find_option_bool() missing from:
x86 setup: early cmdline parser handle boolean options
Also, fix up a minor formatting error in that patch.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Unnecessary capitals are shouting; no need for it here.
Thus, change "OK" to "ok" and add a space.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On early boot, probing the Bios for EDD happens without any message.
Enhanced Disk Drive Services (EDD) is a mechanism to match x86 BIOS device
names (int13 device 80h) to Linux device names (e.g. /dev/sda, /dev/hda)
There are buggy Bios out there having problems with EDD. This can be problems
with the Bios itself or with addon cards, too.
This patch is adds an informational message on early boot.
CONFIG_EDD is not set with defconfig, but with allmodconfig (i.e. CONFIG_EDD=m)
so the EDD probe may be active on early boot on many systems nowadays.
I can tell, that the probe is active on SuSE distro and with that I have seen
more than one system hanging endlessly with those "black screen with a blinking
cursor in the the upper left" on installation, making it difficult for the end-
user to find out, what`s the issue.
For sure I have seen this on FujitsuSiemens PCs with i810 and with i815 chipset.
This one also honours the "quiet" bootparam.
Also see:
http://marc.info/?l=linux-kernel&m=119781937207969&w=2http://marc.info/?l=linux-kernel&m=119783934032326&w=2http://marc.info/?l=linux-kernel&m=119783678529100&w=2
Signed-off-by: Roland Kletzing <devzero@web.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch extends the early commandline parser to support boolean options.
The current version in mainline only supports parsing "option=arg" value pairs.
With this it should be easy making other messages like "Uncompressing kernel"
honour the "quiet" parameter, too.
Signed-off-by: Roland Kletzing <devzero@web.de>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix the operand constraints for the segment accessor functions,
{rd,wr}{fs,gs}*. In particular, the 8-bit functions used "r"
constraints instead of "q" constraints.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Display VESA graphics modes, with their mode IDs, in the vga=ask
menu. Most VESA mode numbers are platform-dependent, so it helps to
have an easy way to display them.
Based in part on a patch by Petr Vandrovec <petr@vandrovec.name>.
Cc: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To set CR0.PE, use the X86_CR0_PE macro defined in
<asm/processor-flags.h> instead of hardcoding it as a constant (1).
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Intel VT doesn't like to engage when the protected-mode state isn't
fully initialized. Make life easier for it by initializing LDTR (to
null) and TR (to a dummy hunk of low memory which will never actually
be touched.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make the transition to protected mode more paranoid by having
back-to-back near jump (to synchronize the 386/486 prefetch queue) and
far jump (to set up the code segment.)
While we're at it, zero as many registers as practical (for future
expandability of the 32-bit entry interface) and enter 32-bit mode
with a valid stack. Note that the 32-bit code cannot rely on this
stack, or we'll break all other existing users of the 32-bit
entrypoint, but it may make debugging hacks easier to write.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The boot protocol has until now required that the initrd be located in
lowmem, which makes the lowmem/highmem boundary visible to the boot
loader. This was exported to the bootloader via a compile-time
field. Unfortunately, the vmalloc= command-line option breaks this
part of the protocol; instead of adding yet another hack that affects
the bootloader, have the kernel relocate the initrd down below the
lowmem boundary inside the kernel itself.
Note that this does not rely on HIGHMEM being enabled in the kernel.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Previously the complete files were #ifdef'ed, but now handle that in the
Makefile.
May save a minor bit of compilation time.
[ Stephen Rothwell <sfr@canb.auug.org.au>: build dependency fix ]
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
