The mptcp conflict was overlapping additions.
The SMC conflict was an additional and removal happening at the same
time.
Signed-off-by: David S. Miller <davem@davemloft.net>
When auto-negotiation is not required, return value should be zero.
Changes v1->v2:
- improved comments and code as Andrew Lunn and Heiner Kallweit suggestion
- fixed issue in genphy_c45_check_and_restart_aneg as Russell King
suggestion.
Fixes: 2a10ab043a ("net: phy: add genphy_check_and_restart_aneg()")
Fixes: 1af9f16840 ("net: phy: add genphy_c45_check_and_restart_aneg()")
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 93c0970493 ("net: phy: consider latched link-down status in
polling mode") removed double-read of latched link-state register for
polling mode from genphy_update_link(). This added extra ~1s delay into
sequence link down->up.
Following scenario:
- After boot link goes up
- phy_start() is called triggering an aneg restart, hence link goes
down and link-down info is latched.
- After aneg has finished link goes up. In phy_state_machine is checked
link state but it is latched "link is down". The state machine is
scheduled after one second and there is detected "link is up". This
extra delay can be avoided when we keep link-state register double read
in case when link was down previously.
With this solution we don't miss a link-down event in polling mode and
link-up is faster.
Details about this quirky behavior on Realtek phy:
Without patch:
T0: aneg is started, link goes down, link-down status is latched
T0+3s: state machine runs, up-to-date link-down is read
T0+4s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
here i read link-down (BMSR_LSTATUS==0),
T0+5s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
up-to-date link-up is read (BMSR_LSTATUS==1),
phydev->link goes up, state change PHY_NOLINK to PHY_RUNNING
With patch:
T0: aneg is started, link goes down, link-down status is latched
T0+3s: state machine runs, up-to-date link-down is read
T0+4s: state machine runs, aneg is finished (BMSR_ANEGCOMPLETE==1),
first BMSR read: BMSR_ANEGCOMPLETE==1 and BMSR_LSTATUS==0,
second BMSR read: BMSR_ANEGCOMPLETE==1 and BMSR_LSTATUS==1,
phydev->link goes up, state change PHY_NOLINK to PHY_RUNNING
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.
The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.
This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.
Fixes: 88d6272aca ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 34786005ec ("net: phy: prevent PHYs w/o Clause 22 regs from calling
genphy_config_aneg") introduced a check that aborts phy_config_aneg()
if the phy is a C45 phy.
This causes phy_state_machine() to call phy_error() so that the phy
ends up in PHY_HALTED state.
Instead of returning -EOPNOTSUPP, call genphy_c45_config_aneg()
(analogous to the C22 case) so that the state machine can run
correctly.
genphy_c45_config_aneg() closely resembles mv3310_config_aneg()
in drivers/net/phy/marvell10g.c, excluding vendor specific
configurations for 1000BaseT.
Fixes: 22b56e8270 ("net: phy: replace genphy_10g_driver with genphy_c45_driver")
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After configuring and restarting aneg we immediately try to read the
link status. On some systems the PHY may not yet have cleared the
"aneg complete" and "link up" bits, resulting in a false link-up
signal. See [0] for a report.
Clause 22 and 45 both require the PHY to keep the AN_RESTART
bit set until the PHY actually starts auto-negotiation.
Let's consider this in the generic functions for reading link status.
The commit marked as fixed is the first one where the patch applies
cleanly.
[0] https://marc.info/?t=156518400300003&r=1&w=2
Fixes: c1164bb1a6 ("net: phy: check PMAPMD link status only in genphy_c45_read_link")
Tested-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Recently a number of generic functions for Clause 45 PHY's has been
added. So let's replace the old very limited genphy_10g_driver with a
genphy_c45_driver. This driver isn't limited to 10G, however it's worth
to be noted that Clause 45 doesn't cover 1000Base-T. For using
1000Base-T with a Clause 45 PHY a dedicated PHY driver using vendor
registers is needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link partner advertisement registers are not guaranteed to contain
valid values if autoneg is incomplete. Therefore, if
MDIO_AN_STAT1_COMPLETE isn't set, let's clear all link partner
capability bits. This also avoids unnecessary register reads if link
is down and phylib is in polling mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mii_lpa_mod_linkmode_lpa_t() checks bit LPA_LPACK to detect
whether link partner supports autoneg. This doesn't work correctly at
least on Aquantia AQCS109 when it negotiates 1000Base-T2 mode.
The "link partner is autoneg-capable" bit as defined by clause 45 is
set however. Better let's switch in general to use the clause 45
standard for link partner autoneg detection.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As can be seen from the usage of the return value, we should use
phy_modify_mmd_changed() here.
Fixes: 9a5dc8af44 ("net: phy: add genphy_c45_an_config_aneg")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
genphy_no_soft_reset and gen10g_no_soft_reset are both the same no-ops,
one is enough.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
gen10g_read_status is deprecated, therefore stop exporting it.
We don't want to encourage anybody to use it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ETHTOOL_LINK_MODE_10000baseT_Full_BIT is set anyway in the supported
and advertising bitmap because it's part of PHY_10GBIT_FEATURES.
And all users of gen10g_config_init use PHY_10GBIT_FEATURES.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_suspend() and phy_resume() are no-ops anyway if no callback is
defined. Therefore we don't need these stubs.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code reports a link as up if all devices (except a few
blacklisted ones) report the link as up. This breaks Aquantia AQCS109
for lower speeds because on this PHY the PCS link status reflects a
10G link only. For Marvell there's a similar issue, therefore PHYXS
device isn't checked.
There may be more PHYs where depending on the mode the link status
of only selected devices is relevant.
For now it seems to be sufficient to check the link status of the
PMAPMD device only. Leave the loop in the code to be prepared in
case we have to add functionality to check more than one device,
depending on the mode.
Successfully tested on a board with an AQCS109.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using genphy_c45_read_abilities() as get_features callback we
also have to set the autoneg capability in phydev->supported.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to genphy_read_status() for Clause 22 add a generic read_status
function for Clause 45.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because 1000BaseT isn't covered by Clause 45, the 1000BaseT flags in
phydev->lp_advertising may have been set based on vendor registers
already. genphy_c45_read_lpa() would clear these flags as of today.
Therefore switch to mii_lpa_mod_linkmode_lpa_t.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used by config_aneg callback implementations of
PHY drivers and allows to reduce boilerplate code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like in genphy_config_aneg() for clause 22 PHY's, we should keep modes
from being advertised that are known to be broken with EEE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When genphy_c45_pma_setup_forced() is called the "aneg enabled" bit may
still be set, therefore clear it. This is also in line with what
genphy_setup_forced() does for Clause 22.
v2:
- fix typo
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use mii_10gbt_stat_mod_linkmode_lpa_t() in genphy_c45_read_lpa() to
simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
C45 configuration of 10/100 and multi-giga bit auto negotiation
advertisement is standardized. Configuration of 1000Base-T however
appears to be vendor specific. Move the generic code out of the
Marvell driver into the common phy-c45.c file.
v2:
- change function name to genphy_c45_an_config_aneg
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[hkallweit1@gmail.com: use new helper linkmode_adv_to_mii_10gbt_adv_t and split patch]
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.3bz specification, based on previous by the NBASET alliance,
defines the 2.5GBaseT and 5GBaseT link modes for ethernet traffic on
cat5e, cat6 and cat7 cables.
These mode integrate with the already defined C45 MDIO PMA/PMD registers
set that added 10G support, by defining some previously reserved bits,
and adding a new register (2.5G/5G Extended abilities).
This commit adds the required definitions in include/uapi/linux/mdio.h
to support these modes, and detect when a link-partner advertises them.
It also adds support for these mode in the generic C45 PHY
infrastructure.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell 10G PHY driver has a generic way of initializing the supported
link modes by reading the PHY's C45 PMA abilities. This can be made
generic, since these registers are part of the 802.3 specifications.
This commit extracts the config_init link_mode initialization code from
marvell10g and uses it to introduce the genphy_c45_pma_read_abilities
function.
Only PMA modes are read, it's still up to the caller to set the Pause
parameters.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status register latches link-down events. Therefore, if link
is reported as being up, there's no need for a second read.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status value latches link-down events. To get the current
status we read the register twice in genphy_update_link(). There's
a potential risk that we miss a link-down event in polling mode.
This may cause issues if the user e.g. connects his machine to a
different network.
On the other hand reading the latched value may cause issues in
interrupt mode. Following scenario:
- After boot link goes up
- phy_start() is called triggering an aneg restart, hence link goes
down and link-down info is latched.
- After aneg has finished link goes up and triggers an interrupt.
Interrupt handler reads link status, means it reads the latched
"link is down" info. But there won't be another interrupt as long
as link stays up, therefore phylib will never recognize that link
is up.
Deal with both scenarios by reading the register twice in interrupt
mode only.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let genphy_c45_read_link manage the devices to check, this removes
overhead from callers. Add C22EXT to the list of excluded devices
because it doesn't implement the status register. According to the
802.3 clause 45 spec registers 29.0 - 29.4 are reserved.
At the moment we have very few clause 45 PHY drivers, so we are
lacking experience whether other drivers will have to exclude further
devices, or may need to check PHY XS. If we should figure out that
list of devices to check needs to be configurable, I think best will
be to add a device list member to struct phy_driver.
v2:
- adjusted commit message
- exclude also device C22EXT from link checking
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's make genphy_c45_read_link behave the same as genphy_update_link
and set phydev->link in the function directly. This allows to simplify
the callers. In addition don't check further devices once we detect
that at least one device reports link as down.
v2:
- remove an unused variable
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the new MMD accessors.
v2:
- fix SoB
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert phy drivers to report the link partner advertised modes using
a linkmode bitmap. This allows them to report the higher speeds which
don't fit in a u32.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few MAC/PHYs combinations which now support > 1Gbps. These
may need to make use of link modes with bits > 31. Thus their
supported PHY features or advertised features cannot be implemented
using the current bitmap in a u32. Convert to using a linkmode bitmap,
which can support all the currently devices link modes, and is future
proof as more modes are added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver got missed during the recent change of .features from a
u32 to a pointer to a Linux bitmap. Change the initialisation from 0
to PHY_10GBIT_FEATURES so removing the danger of a NULL pointer
dereference.
Fixes: 719655a149 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Jose Abreu <jose.abreu@synopsys.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in comments and error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to remove a fair amount of duplication in the different 10G PHY
drivers, export all gen10g_* functions to be able to make use of those.
While we are at it, rename gen10g_soft_reset() to gen10g_no_soft_reset()
to illustrate what it does.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add reporting of the MDI swap to the Marvell 10G PHY driver by providing
a generic implementation for the standard 10GBASE-T pair swap register
and polarity register. We also support reading the MDI swap status for
1G and below from a PCS register.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the old 10G genphy support to sit beside the new clause 45 library
functions, so all the 10G phy code is together.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic helpers for 802.3 clause 45 PHYs for >= 10Gbps support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
