8000 series adapters support filtering VXLAN, NVGRE and GENEVE traffic
based on inner fields, and when the NIC recognises such traffic, it
does not match unencapsulated traffic filters any more. So add catch-
all filters for encapsulated traffic on supporting platforms.
Although recognition of VXLAN and GENEVE is based on UDP ports, and thus
will not occur until the driver (on the primary PF) notifies the
firmware of UDP ports to use, NVGRE will always be recognised, hence
without this patch 8000 series adapters will drop all NVGRE traffic.
Partly based on patches by Jon Cooper <jcooper@solarflare.com>.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rationalise several debug-or-warnings printks using netif_cond_dbg
to make output more consistent.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For reporting things that may or may not be serious, depending on some
condition, netif_cond_dbg will check the condition and print the report
at either dbg (if the condition is true) or the specified level.
Suggested-by: Jon Cooper <jcooper@solarflare.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NIC is switched from full-featured to low-latency, encapsulated
filters are no longer available, and this causes errors. This patch
removes those filters from the filter table on restore.
Also, if filters which are removed by the above, or which we fail to
insert when restoring filters, were UC, MC or broadcast default
filters, invalidate the corresponding vlan->default_filters entry.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stats member of struct frad_locl is used neither by the dlci nor the
sdla driver, so it might as well be removed.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's Broadcom PHY simply described as single-port
RGMII 10/100/1000BASE-T PHY. It requires disabling delay skew and GTXCLK
bits.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEES2FAuYbJvAGobdVQPTuqJaypJWoFAliHTm8THG1rbEBwZW5n
dXRyb25peC5kZQAKCRA9O6olrKklajYkB/wOJxby2DFi4ukCPyrTpXtkQWmXa6+M
Wr/nY5PBg88JipQ+u3rl6bW9NMF3U3xtPO6I/ezfn1jfWOTg0jVIecEfqlW8JNAU
275IOaiQ7jYgGEo+ALUAv2kSe7Fl8HQyaq+9ugMkWUTdv5Vjay1GZgCzyKZzjM8q
8UOoB1YsXlB9f230HPMLeHcbGHqHCOpfNk9yWNcbd0Up6U7EweXtK4Pf/L8g+bL1
0LR1QHRoUtmivuIi96KhB7O/+w8WuigWRy7qkfGpFescZQWOHzbwCVHlZ9ZYCOnJ
eGEP8koksJuMg4OoEUCv0k2v3Txnfr8YNC5MvNdQ06YmoBWwQeamCozL
=fBeU
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.11-20170124' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2017-01-24
this is a pull request of 4 patches for net-next/master.
The first patch by Oliver Hartkopp adds a netlink API to configure the
interface termination of a CAN card. The next two patches are by me and
add a netlink API to query and configure CAN interfaces that only
support fixed bitrates. The last patch by Colin Ian King simplifies the
return path in the softing_cs driver's softingcs_probe() function.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The address generation mode for IPv6 link-local can only be configured
by netlink messages. This patch adds the ability to change the address
generation mode via sysctl.
v1 -> v2
Removed the rtnl lock and switch to use RCU lock to iterate through
the netdev list.
v2 -> v3
Removed the addrgenmode variable from the idev structure and use the
systcl storage for the flag.
Simplifed the logic for sysctl handling by removing the supported
for all operation.
Added support for more types of tunnel interfaces for link-local
address generation.
Based the patches from net-next.
v3 -> v4
Removed unnecessary whitespace changes.
Signed-off-by: Felix Jia <felix.jia@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 16e5cc6471 ("net: rework setup_tc ndo op to consume
general tc operand") changed the ndo_setup_tc() signature, but did not
update the comments in netdevice.h, so do that now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lkp-robot reported a BUG:
[ 10.151226] BUG: unable to handle kernel NULL pointer dereference at 00000198
[ 10.152525] IP: rt6_fill_node+0x164/0x4b8
[ 10.153307] *pdpt = 0000000012ee5001 *pde = 0000000000000000
[ 10.153309]
[ 10.154492] Oops: 0000 [#1]
[ 10.154987] CPU: 0 PID: 909 Comm: netifd Not tainted 4.10.0-rc4-00722-g41e8c70ee162-dirty #10
[ 10.156482] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
[ 10.158254] task: d0deb000 task.stack: d0e0c000
[ 10.159059] EIP: rt6_fill_node+0x164/0x4b8
[ 10.159780] EFLAGS: 00010296 CPU: 0
[ 10.160404] EAX: 00000000 EBX: d10c2358 ECX: c1f7c6cc EDX: c1f6ff44
[ 10.161469] ESI: 00000000 EDI: c2059900 EBP: d0e0dc4c ESP: d0e0dbe4
[ 10.162534] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
[ 10.163482] CR0: 80050033 CR2: 00000198 CR3: 10d94660 CR4: 000006b0
[ 10.164535] Call Trace:
[ 10.164993] ? paravirt_sched_clock+0x9/0xd
[ 10.165727] ? sched_clock+0x9/0xc
[ 10.166329] ? sched_clock_cpu+0x19/0xe9
[ 10.166991] ? lock_release+0x13e/0x36c
[ 10.167652] rt6_dump_route+0x4c/0x56
[ 10.168276] fib6_dump_node+0x1d/0x3d
[ 10.168913] fib6_walk_continue+0xab/0x167
[ 10.169611] fib6_walk+0x2a/0x40
[ 10.170182] inet6_dump_fib+0xfb/0x1e0
[ 10.170855] netlink_dump+0xcd/0x21f
This happens when the loopback device is set down and a ipv6 fib route
dump is requested.
ip6_null_entry is the root of all ipv6 fib tables making it integrated
into the table and hence passed to the ipv6 route dump code. The
null_entry route uses the loopback device for dst.dev but may not have
rt6i_idev set because of the order in which initializations are done --
ip6_route_net_init is run before addrconf_init has initialized the
loopback device. Fixing the initialization order is a much bigger problem
with no obvious solution thus far.
The BUG is triggered when the loopback is set down and the netif_running
check added by a1a22c1206 fails. The fill_node descends to checking
rt->rt6i_idev for ignore_routes_with_linkdown and since rt6i_idev is
NULL it faults.
The null_entry route should not be processed in a dump request. Catch
and ignore. This check is done in rt6_dump_route as it is the highest
place in the callchain with knowledge of both the route and the network
namespace.
Fixes: a1a22c1206("net: ipv6: Keep nexthop of multipath route on admin down")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove skb_reserve and skb_reset_mac_header from inet6_rtm_getroute. The
allocated skb is not passed through the routing engine (like it is for
IPv4) and has not since the beginning of git time.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: Preparatory patches
This patch series extracts the 4 patches of the larger: net: dsa: Support for
pdata in dsa2 while we wait for feedback from Greg KH on the device references.
Changes in v2:
- rebased properly after the multi-MDIO bus support added to mv88e6xxx
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the assignment of ports in _dsa_register_switch() closer to where
it is checked, no functional change. Re-order declarations to be
preserve the inverted christmas tree style.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that these functions take a device_node structure pointer
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing platform data, and therefore no valid
device_node pointer, make most DSA functions takes a pointer to a
dsa_port structure whenever possible. While at it, introduce a
dsa_port_is_valid() helper function which checks whether port->dn is
NULL or not at the moment.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing dsa_register_switch() to be supplied with
device/platform data, pass down a struct device pointer instead of a
struct device_node.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Accessing skb after submitting to input queue can cause
access to stale pointers if the skb ends up being transmitted
and freed by that time.
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- bump version strings, by Simon Wunderlich
- ignore self-generated loop detect MAC addresses in translation table,
by Simon Wunderlich
- install uapi batman_adv.h header, by Sven Eckelmann
- bump copyright years, by Sven Eckelmann
- Remove an unused variable in translation table code, by Sven Eckelmann
- Handle NET_XMIT_CN like NET_XMIT_SUCCESS (revised according to Davids
suggestion), and a follow up code clean up, by Gao Feng (2 patches)
-----BEGIN PGP SIGNATURE-----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=cd1Y
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20170126' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- ignore self-generated loop detect MAC addresses in translation table,
by Simon Wunderlich
- install uapi batman_adv.h header, by Sven Eckelmann
- bump copyright years, by Sven Eckelmann
- Remove an unused variable in translation table code, by Sven Eckelmann
- Handle NET_XMIT_CN like NET_XMIT_SUCCESS (revised according to Davids
suggestion), and a follow up code clean up, by Gao Feng (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
I noticed that this function uses a lot of kernel stack when the
"latent entropy" plugin is enabled:
drivers/isdn/hardware/eicon/message.c: In function 'sig_ind':
drivers/isdn/hardware/eicon/message.c:6113:1: error: the frame size of 1168 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]
We currently don't warn about this, as we raise the warning limit
to 2048 bytes in mainline, but I'd like to lower that limit again
in the future, and this function can easily be changed to be more
efficient and avoid that warning, by making some of its local
variables 'const'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tc could return NET_XMIT_CN as one congestion notification, but
it does not mean the packet is lost. Other modules like ipvlan,
macvlan, and others treat NET_XMIT_CN as success too.
So batman-adv should handle NET_XMIT_CN also as NET_XMIT_SUCCESS.
Signed-off-by: Gao Feng <gfree.wind@gmail.com>
[sven@narfation.org: Moved NET_XMIT_CN handling to batadv_send_skb_packet]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It could decrease one condition check to collect some statements in the
first condition block.
Signed-off-by: Gao Feng <gfree.wind@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
09748a22f4 ("batman-adv: add generic netlink family for batman-adv")
introduced the new batman_adv.h which describes the netlink attributes and
commands of batman-adv. But the Kbuild entry to install the header was not
added.
All currently known tools ship their own copy of batman_adv.h but it should
be installed anyway to later be able to migrate to the system batman_adv.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The bridge loop avoidance (BLA) feature of batman-adv sends packets to
probe for Mesh/LAN packet loops. Those packets are not sent by real
clients and should therefore not be added to the translation table (TT).
Signed-off-by: Simon Wunderlich <simon.wunderlich@open-mesh.com>
The only caller of this new function is inside of an #ifdef checking
for CONFIG_BRIDGE_IGMP_SNOOPING, so we should move the implementation
there too, in order to avoid this harmless warning:
net/bridge/br_forward.c:177:13: error: 'maybe_deliver_addr' defined but not used [-Werror=unused-function]
Fixes: 6db6f0eae6 ("bridge: multicast to unicast")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently used len instead of prefix_len for the strncmp() in
fdinfo on the prog_tag. It still worked as we matched on the correct
output line also with first 8 instead of 10 chars, but lets fix it
properly to use the intended length.
Fixes: 62b6466026 ("bpf: add prog tag test case to bpf selftests")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafał Miłecki says:
====================
net-next: Broadcom PHY driver cleanup
I will probably need to use broadcom.ko for PHY connected to interface
of bgmac supported device so I started looking at it willing to
understand it better.
I found AUXCTL part of the driver / lib a bit confusing and hard to read
so I'm trying to clean it up a bit. I hope this patchset makes following
AUXCTL operations much easier making it clear which defines are for
registers and which for values.
There is no functional change in this pachset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
1) Use 0x%02x format for register number. This follows some other
defines and makes it easier to distinct register from values.
2) Put register define above values and sort the values. It makes
reading header code easier.
3) Use 0x%04x format for all values. It's about consistency with other
values (and most of the header) not a personal preference.
4) Separate define for reading shift value with an extre empty line.
It's user for all AUXCTL registers in a bcm54xx_auxctl_read.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had two defines for the same bit (both were used with the
MII_BCM54XX_AUXCTL_SHDWSEL_MISC register).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Starting with commit 5b4e290051 ("net: phy: broadcom: add
bcm54xx_auxctl_read") we have a reading helper so use it and avoid code
duplication.
It also means we don't need MII_BCM54XX_AUXCTL_SHDWSEL_MISC define as
it's the same as MII_BCM54XX_AUXCTL_SHDWSEL_MISC just for reading needs
(same value shifted by 12 bits).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patches have moved the temperature sensor code into the
Marvell PHYs. A few now dead references to NET_DSA_HWMON were left
behind. Go reap them.
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PIO buffer allocation can fail for two valid reasons:
- we've run out of them (results in -ENOSPC)
- the NIC configuration doesn't support them (results in -EPERM)
Since both these failures are expected netif_err is excessive.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sunil Goutham says:
====================
thunderx: More ethtool support and BGX configuration changes
These patches adds support to set queue sizes from ethtool and changes
the way serdes lane configuration is done by BGX driver on 81/83xx
platforms.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For DLMs and SLMs on 80/81/83xx, many lane configurations
across different boards are coming up. Also kernel doesn't have
any way to identify board type/info and since firmware does,
just get rid of figuring out lane to serdes config and take
whatever has been programmed by low level firmware.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support to set Rx/Tx queue sizes from ethtool. Fixes
an issue with retrieving queue size. Also sets SQ's CQ_LIMIT
based on configured Tx queue size such that HW doesn't process
SQEs when there is no sufficient space in CQ.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without TFO, any subsequent connect() call after a successful one returns
-1 EISCONN. The last API update ensured that __inet_stream_connect() can
return -1 EINPROGRESS in response to sendmsg() when TFO is in use to
indicate that the connection is now in progress. Unfortunately since this
function is used both for connect() and sendmsg(), it has the undesired
side effect of making connect() now return -1 EINPROGRESS as well after
a successful call, while at the same time poll() returns POLLOUT. This
can confuse some applications which happen to call connect() and to
check for -1 EISCONN to ensure the connection is usable, and for which
EINPROGRESS indicates a need to poll, causing a loop.
This problem was encountered in haproxy where a call to connect() is
precisely used in certain cases to confirm a connection's readiness.
While arguably haproxy's behaviour should be improved here, it seems
important to aim at a more robust behaviour when the goal of the new
API is to make it easier to implement TFO in existing applications.
This patch simply ensures that we preserve the same semantics as in
the non-TFO case on the connect() syscall when using TFO, while still
returning -1 EINPROGRESS on sendmsg(). For this we simply tell
__inet_stream_connect() whether we're doing a regular connect() or in
fact connecting for a sendmsg() call.
Cc: Wei Wang <weiwan@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wei Wang says:
====================
net/tcp-fastopen: Add new userspace API support
The patch series is to add support for new userspace API for TCP fastopen
sockets.
In the current code, user has to call sendto()/sendmsg() with special flag
MSG_FASTOPEN for TCP fastopen sockets. This API is quite different from the
normal TCP socket API and can be cumbersome for applications to make use
fastopen sockets.
So this new patch introduces a new way of using TCP fastopen sockets which
is similar to normal TCP sockets with a new sockopt TCP_FASTOPEN_CONNECT.
More details about it is described in the third patch.
(First 2 patches are preparations for the third patch.)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new socket option, TCP_FASTOPEN_CONNECT, as an
alternative way to perform Fast Open on the active side (client). Prior
to this patch, a client needs to replace the connect() call with
sendto(MSG_FASTOPEN). This can be cumbersome for applications who want
to use Fast Open: these socket operations are often done in lower layer
libraries used by many other applications. Changing these libraries
and/or the socket call sequences are not trivial. A more convenient
approach is to perform Fast Open by simply enabling a socket option when
the socket is created w/o changing other socket calls sequence:
s = socket()
create a new socket
setsockopt(s, IPPROTO_TCP, TCP_FASTOPEN_CONNECT …);
newly introduced sockopt
If set, new functionality described below will be used.
Return ENOTSUPP if TFO is not supported or not enabled in the
kernel.
connect()
With cookie present, return 0 immediately.
With no cookie, initiate 3WHS with TFO cookie-request option and
return -1 with errno = EINPROGRESS.
write()/sendmsg()
With cookie present, send out SYN with data and return the number of
bytes buffered.
With no cookie, and 3WHS not yet completed, return -1 with errno =
EINPROGRESS.
No MSG_FASTOPEN flag is needed.
read()
Return -1 with errno = EWOULDBLOCK/EAGAIN if connect() is called but
write() is not called yet.
Return -1 with errno = EWOULDBLOCK/EAGAIN if connection is
established but no msg is received yet.
Return number of bytes read if socket is established and there is
msg received.
The new API simplifies life for applications that always perform a write()
immediately after a successful connect(). Such applications can now take
advantage of Fast Open by merely making one new setsockopt() call at the time
of creating the socket. Nothing else about the application's socket call
sequence needs to change.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove __sk_dst_reset() in the failure handling because __sk_dst_reset()
will eventually get called when sk is released. No need to handle it in
the protocol specific connect call.
This is also to make the code path consistent with ipv4.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the cookie check logic in tcp_send_syn_data() into a function.
This function will be called else where in later changes.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace spaces with tabs. Fix indentation to be multiples of tabs, not
a mixture or tabs and spaces.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
BPF tracepoints
This set adds tracepoints to BPF for better introspection and
debugging. The first two patches are prerequisite for the actual
third patch that adds the tracepoints. I think the first two are
small and straight forward enough that they could ideally go via
net-next, but I'm also open to other suggestions on how to route
them in case that's not applicable (it would reduce potential
merge conflicts on BPF side, though). For details, please see
individual patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This work adds a number of tracepoints to paths that are either
considered slow-path or exception-like states, where monitoring or
inspecting them would be desirable.
For bpf(2) syscall, tracepoints have been placed for main commands
when they succeed. In XDP case, tracepoint is for exceptions, that
is, f.e. on abnormal BPF program exit such as unknown or XDP_ABORTED
return code, or when error occurs during XDP_TX action and the packet
could not be forwarded.
Both have been split into separate event headers, and can be further
extended. Worst case, if they unexpectedly should get into our way in
future, they can also removed [1]. Of course, these tracepoints (like
any other) can be analyzed by eBPF itself, etc. Example output:
# ./perf record -a -e bpf:* sleep 10
# ./perf script
sock_example 6197 [005] 283.980322: bpf:bpf_map_create: map type=ARRAY ufd=4 key=4 val=8 max=256 flags=0
sock_example 6197 [005] 283.980721: bpf:bpf_prog_load: prog=a5ea8fa30ea6849c type=SOCKET_FILTER ufd=5
sock_example 6197 [005] 283.988423: bpf:bpf_prog_get_type: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
sock_example 6197 [005] 283.988443: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[06 00 00 00] val=[00 00 00 00 00 00 00 00]
[...]
sock_example 6197 [005] 288.990868: bpf:bpf_map_lookup_elem: map type=ARRAY ufd=4 key=[01 00 00 00] val=[14 00 00 00 00 00 00 00]
swapper 0 [005] 289.338243: bpf:bpf_prog_put_rcu: prog=a5ea8fa30ea6849c type=SOCKET_FILTER
[1] https://lwn.net/Articles/705270/
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the __print_hex_str() macro that was added for
tracing, so that user space tools such as perf can understand
it as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For upcoming tracepoint support for BPF, we want to dump the program's
tag. Format should be similar to __print_hex(), but without spacing.
Add a __print_hex_str() variant for exactly that purpose that reuses
trace_print_hex_seq().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_add_backlog() can use skb_condense() helper to get better
gains and less SKB_TRUESIZE() magic. This only happens when socket
backlog has to be used.
Some attacks involve specially crafted out of order tiny TCP packets,
clogging the ofo queue of (many) sockets.
Then later, expensive collapse happens, trying to copy all these skbs
into single ones.
This unfortunately does not work if each skb has no neighbor in TCP
sequence order.
By using skb_condense() if the skb could not be coalesced to a prior
one, we defeat these kind of threats, potentially saving 4K per skb
(or more, since this is one page fragment).
A typical NAPI driver allocates gro packets with GRO_MAX_HEAD bytes
in skb->head, meaning the copy done by skb_condense() is limited to
about 200 bytes.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first seven patches from Or Gerlitz in this series further enhances
the mlx5 SRIOV switchdev mode to support offloading IPv6 tunnels using the
TC tunnel key set (encap) and unset (decap) actions.
Or Gerlitz says:
========================
As part of doing this change, few cleanups are done in the IPv4 code,
later we move to use the full tunnel key info provided to the driver as
the key for our internal hashing which is used to identify cases where
the same tunnel is used for encapsulating multiple flows. As done in the
IPv4 case, the control path for offloading IPv6 tunnels uses route/neigh
lookups and construction of the IPv6 tunnel headers on the encap path and
matching on the outer hears in the decap path.
The last patch of the series enlarges the HW FDB size for the switchdev mode,
so it has now room to contain offloaded flows as many as min(max number
of HW flow counters supported, max HW table size supported).
========================
Next to Or's series you can find several patches handling several topics.
From Mohamad, add support for SRIOV VF min rate guarantee by using the
TSAR BW share weights mechanism.
From Or, Two patches to enable Eth VFs to query their min-inline value for
user-space.
for that we move a mlx5 low level min inline helper function from mlx5
ethernet driver into the core driver and then use it in mlx5_ib to expose
the inline mode to rdma applications through libmlx5.
From Kamal Heib, Reduce memory consumption on kdump kernel.
From Shaker Daibes, code reuse in CQE compression control logic
Thanks,
Saeed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYh7FNAAoJEEg/ir3gV/o+TjsIAL1e92+5eutBS9ZvhMARi+Tc
c2V9V8bG8W1RWWTvx1G0aU4nNjWsr5L8Q8gzqpwhrQITBfgpWd+hlnxQCucyhxC3
AC1qQ+AKREe/C+25D+WJRq34/61ZHEH2rbKZvpZ1O8SuicVPbcvJ9eM+wOEDxwwX
u5C5kWQ0HRtCcnFiiOYkB+0CQPH7m3+ZzZek+jDowrexHMSE+yl8ZNtaSTX9c9QN
bE2cPiCVZd7ufKPIwY8LWHBryyl7sh5P+NqzD633OeiqP/pkZsW9A+czyt+d330f
6XTKOS1PCD+TfHE0sZJT4VMCjICMHrOFbNRZuwcxJQ6NfmwIJZfskX4NLbyGQTI=
=vF7U
-----END PGP SIGNATURE-----
Merge tag 'mlx5-updates-2017-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-24-01
The first seven patches from Or Gerlitz in this series further enhances
the mlx5 SRIOV switchdev mode to support offloading IPv6 tunnels using the
TC tunnel key set (encap) and unset (decap) actions.
Or Gerlitz says:
========================
As part of doing this change, few cleanups are done in the IPv4 code,
later we move to use the full tunnel key info provided to the driver as
the key for our internal hashing which is used to identify cases where
the same tunnel is used for encapsulating multiple flows. As done in the
IPv4 case, the control path for offloading IPv6 tunnels uses route/neigh
lookups and construction of the IPv6 tunnel headers on the encap path and
matching on the outer hears in the decap path.
The last patch of the series enlarges the HW FDB size for the switchdev mode,
so it has now room to contain offloaded flows as many as min(max number
of HW flow counters supported, max HW table size supported).
========================
Next to Or's series you can find several patches handling several topics.
From Mohamad, add support for SRIOV VF min rate guarantee by using the
TSAR BW share weights mechanism.
From Or, Two patches to enable Eth VFs to query their min-inline value for
user-space.
for that we move a mlx5 low level min inline helper function from mlx5
ethernet driver into the core driver and then use it in mlx5_ib to expose
the inline mode to rdma applications through libmlx5.
From Kamal Heib, Reduce memory consumption on kdump kernel.
From Shaker Daibes, code reuse in CQE compression control logic
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
