MOV CR/DR instructions ignore the mod field (in the ModR/M byte). As the SDM
states: "The 2 bits in the mod field are ignored". Accordingly, the second
operand of these instructions is always a general purpose register.
The current emulator implementation does not do so. If the mod bits do not
equal 3, it expects the second operand to be in memory.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Table 7-1 of the SDM mentions a check that the code segment's
DPL must match the selector's RPL. This was not done by KVM,
fix it.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
During task switch, all of CS.DPL, CS.RPL, SS.DPL must match (in addition
to all the other requirements) and will be the new CPL. So far this
worked by carefully setting the CS selector and flag before doing the
task switch; setting CS.selector will already change the CPL.
However, this will not work once we get the CPL from SS.DPL, because
then you will have to set the full segment descriptor cache to change
the CPL. ctxt->ops->cpl(ctxt) will then return the old CPL during the
task switch, and the check that SS.DPL == CPL will fail.
Temporarily assume that the CPL comes from CS.RPL during task switch
to a protected-mode task. This is the same approach used in QEMU's
emulation code, which (until version 2.0) manually tracks the CPL.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The IN instruction is not be affected by REP-prefix as INS is. Therefore, the
emulation should ignore the REP prefix as well. The current emulator
implementation tries to perform writeback when IN instruction with REP-prefix
is emulated. This causes it to perform wrong memory write or spurious #GP
exception to be injected to the guest.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
According to Intel specifications, PAE and non-PAE does not have any reserved
bits. In long-mode, regardless to PCIDE, only the high bits (above the
physical address) are reserved.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
According to Intel specifications, only general purpose registers and segment
selectors should be saved in the old TSS during 32-bit task-switch.
Signed-off-by: Nadav Amit <namit@cs.technion.ac.il>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Add emulation for 0x66 prefixed instruction of 0f 28 opcode
that has been added earlier.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
All decode_register() callers check if instruction has rex prefix
to properly decode one byte operand. It make sense to move the check
inside.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
When I was looking at RHEL5.9's failure to start with
unrestricted_guest=0/emulate_invalid_guest_state=1, I got it working with a
slightly older tree than kvm.git. I now debugged the remaining failure,
which was introduced by commit 660696d1 (KVM: X86 emulator: fix
source operand decoding for 8bit mov[zs]x instructions, 2013-04-24)
introduced a similar mis-emulation to the one in commit 8acb4207 (KVM:
fix sil/dil/bpl/spl in the mod/rm fields, 2013-05-30). The incorrect
decoding occurs in 8-bit movzx/movsx instructions whose 8-bit operand
is sil/dil/bpl/spl.
Needless to say, "movzbl %bpl, %eax" does occur in RHEL5.9's decompression
prolog, just a handful of instructions before finally giving control to
the decompressed vmlinux and getting out of the invalid guest state.
Because OpMem8 bypasses decode_modrm, the same handling of the REX prefix
must be applied to OpMem8.
Reported-by: Michele Baldessari <michele@redhat.com>
Cc: stable@vger.kernel.org
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Yet another instruction that we fail to emulate, this time found
in Windows 2008R2 32-bit.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
This basically came from the need to be able to boot 32-bit Atom SMP
guests on an AMD host, i.e. a host which doesn't support MOVBE. As a
matter of fact, qemu has since recently received MOVBE support but we
cannot share that with kvm emulation and thus we have to do this in the
host. We're waay faster in kvm anyway. :-)
So, we piggyback on the #UD path and emulate the MOVBE functionality.
With it, an 8-core SMP guest boots in under 6 seconds.
Also, requesting MOVBE emulation needs to happen explicitly to work,
i.e. qemu -cpu n270,+movbe...
Just FYI, a fairly straight-forward boot of a MOVBE-enabled 3.9-rc6+
kernel in kvm executes MOVBE ~60K times.
Signed-off-by: Andre Przywara <andre@andrep.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add initial support for handling three-byte instructions in the
emulator.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Call it EmulateOnUD which is exactly what we're trying to do with
vendor-specific instructions.
Rename ->only_vendor_specific_insn to something shorter, while at it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a field to the current emulation context which contains the
instruction opcode length. This will streamline handling of opcodes of
different length.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Opcode CA
This gets used by a DOS based NetWare guest.
Signed-off-by: Bruce Rogers <brogers@suse.com>
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
On the x86 side, there are some optimizations and documentation updates.
The big ARM/KVM change for 3.11, support for AArch64, will come through
Catalin Marinas's tree. s390 and PPC have misc cleanups and bugfixes.
There is a conflict due to "s390/pgtable: fix ipte notify bit" having
entered 3.10 through Martin Schwidefsky's s390 tree. This pull request
has additional changes on top, so this tree's version is the correct one.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=1zpG
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Paolo Bonzini:
"On the x86 side, there are some optimizations and documentation
updates. The big ARM/KVM change for 3.11, support for AArch64, will
come through Catalin Marinas's tree. s390 and PPC have misc cleanups
and bugfixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (87 commits)
KVM: PPC: Ignore PIR writes
KVM: PPC: Book3S PR: Invalidate SLB entries properly
KVM: PPC: Book3S PR: Allow guest to use 1TB segments
KVM: PPC: Book3S PR: Don't keep scanning HPTEG after we find a match
KVM: PPC: Book3S PR: Fix invalidation of SLB entry 0 on guest entry
KVM: PPC: Book3S PR: Fix proto-VSID calculations
KVM: PPC: Guard doorbell exception with CONFIG_PPC_DOORBELL
KVM: Fix RTC interrupt coalescing tracking
kvm: Add a tracepoint write_tsc_offset
KVM: MMU: Inform users of mmio generation wraparound
KVM: MMU: document fast invalidate all mmio sptes
KVM: MMU: document fast invalidate all pages
KVM: MMU: document fast page fault
KVM: MMU: document mmio page fault
KVM: MMU: document write_flooding_count
KVM: MMU: document clear_spte_count
KVM: MMU: drop kvm_mmu_zap_mmio_sptes
KVM: MMU: init kvm generation close to mmio wrap-around value
KVM: MMU: add tracepoint for check_mmio_spte
KVM: MMU: fast invalidate all mmio sptes
...
The x86-64 extended low-byte registers were fetched correctly from reg,
but not from mod/rm.
This fixes another bug in the boot of RHEL5.9 64-bit, but it is still
not enough.
Cc: <stable@vger.kernel.org> # 3.9
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
This is encountered when booting RHEL5.9 64-bit. There is another bug
after this one that is not a simple emulation failure, but this one lets
the boot proceed a bit.
Cc: <stable@vger.kernel.org> # 3.9
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Since DIV and IDIV can generate exceptions, we need an additional output
parameter indicating whether an execption has occured. To avoid increasing
register pressure on i386, we use %rsi, which is already allocated for
the fastop code pointer.
Gleb: added comment about fop usage as exception indication.
Signed-off-by: Avi Kivity <avi.kivity@gmail.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Single-operand MUL and DIV access an extended accumulator: AX for byte
instructions, and DX:AX, EDX:EAX, or RDX:RAX for larger-sized instructions.
Add support for fetching the extended accumulator.
In order not to change things too much, RDX is loaded into Src2, which is
already loaded by fastop(). This avoids increasing register pressure on
i386.
Gleb: disable src writeback for ByteOp div/mul.
Signed-off-by: Avi Kivity <avi.kivity@gmail.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Some instructions write back the source operand, not just the destination.
Add support for doing this via the decode flags.
Gleb: add BUG_ON() to prevent source to be memory operand.
Signed-off-by: Avi Kivity <avi.kivity@gmail.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
This is an almost-undocumented instruction available in 32-bit mode.
I say "almost" undocumented because AMD documents it in their opcode
maps just to say that it is unavailable in 64-bit mode (sections
"A.2.1 One-Byte Opcodes" and "B.3 Invalid and Reassigned Instructions
in 64-Bit Mode").
It is roughly equivalent to "sbb %al, %al" except it does not
set the flags. Use fastop to emulate it, but do not use the opcode
directly because it would fail if the host is 64-bit!
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: stable@vger.kernel.org # 3.9
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
This is used by SGABIOS, KVM breaks with emulate_invalid_guest_state=1.
It is just a MOV in disguise, with a funny source address.
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: stable@vger.kernel.org # 3.9
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
This is used by SGABIOS, KVM breaks with emulate_invalid_guest_state=1.
AAM needs the source operand to be unsigned; do the same in AAD as well
for consistency, even though it does not affect the result.
Reported-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: stable@vger.kernel.org # 3.9
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Source operand for one byte mov[zs]x is decoded incorrectly if it is in
high byte register. Fix that.
Cc: stable@vger.kernel.org
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Emulation of undefined opcode should inject #UD instead of causing
emulation failure. Do that by moving Undefined flag check to emulation
stage and injection #UD there.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Unimplemented instruction detection is broken for group instructions
since it relies on "flags" field of opcode to be zero, but all
instructions in a group inherit flags from a group encoding. Fix that by
having a separate flag for unimplemented instructions.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
This fixes a regression introduced in commit 03ebebeb1 ("KVM: x86
emulator: Leave segment limit and attributs alone in real mode").
The mentioned commit changed the segment descriptors for both real mode
and VM86 to only update the segment base instead of creating a
completely new descriptor with limit 0xffff so that unreal mode keeps
working across a segment register reload.
This leads to an invalid segment descriptor in the eyes of VMX, which
seems to be okay for real mode because KVM will fix it up before the
next VM entry or emulate the state, but it doesn't do this if the guest
is in VM86, so we end up with:
KVM: entry failed, hardware error 0x80000021
Fix this by effectively reverting commit 03ebebeb1 for VM86 and leaving
it only in place for real mode, which is where it's really needed.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
'pushq' doesn't exist on i386. Replace with 'push', which should work
since the operand is a register.
Signed-off-by: Avi Kivity <avi.kivity@gmail.com>
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Make fastop opcodes usable in other emulations.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi.kivity@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
This is a bit of a special case since we don't have the usual
byte/word/long/quad switch; instead we switch on the condition code embedded
in the instruction.
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi.kivity@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Opcodes:
TEST
CMP
ADD
ADC
SUB
SBB
XOR
OR
AND
Acked-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Avi Kivity <avi.kivity@gmail.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
