In drivers/mmc/core/host.c, there is a "max-frequency" property.
Behavior should not change, so use the "max-frequency" instead of
"clock-freq-min-max".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos4 like other Cortex-A9 SoC's has a Snoop Control Unit(SCU)
and its SFR are used during SMP boot and S2R. Add SCU node to the device tree.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
There are no boards in mainline using exynos4415.dtsi. These DTSIs
were not tested for long. I am also not aware of any popular out-of-tree
boards using this (except consumer devices released by Samsung but those
cannot use mainline).
Keeping Exynos4415 costs some useless effort so remove it.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
There's a cognitive load to figure out which mmc device node corresponds
to the eMMC flash, uSD card and WiFI SDIO module on the Snow, Peach Pi
and Pit boards.
So it's better to have comments in the DTS to make this more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
[krzk: Squashed three patches into one]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The TOPEET itop Exynos4412 has three versions of base boards. The
Elite version is the cheap one without too much peripheral devices
on it.
Currently supported are serial console, wired networking (USB), USB OTG
in peripheral mode, USB host, SD storage, GPIO buttons, PWM beeper, ADC
and LEDs. The WM8960 analog audio codec is also enabled.
The FIMC is not used for camera currently, I enabled it just for a
colorspace converter.
Signed-off-by: Randy Li <ayaka@soulik.info>
Acked-by: Rob Herring <robh@kernel.org>
[krzk: fixup pin function macro, adjust commit msg]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The TOPEET itop is a Samsung Exynos4412 core board, which has
two package versions. This patch adds the support for SCP version.
Currently supported are USB3503A HSIC, USB OTG, eMMC, RTC and
PMIC. The future features are in the based board. Also MFC and
watchdog have been enabled.
Signed-off-by: Randy Li <ayaka@soulik.info>
[krzk: fixup pin function macro, adjust commit msg]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds device nodes for the AUDSS clock controller,
peripheral DMA 0/1 controllers and the Audio Subsystem I2S controller.
These entries are required for sound support on Odroid-XU board.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The "simple-bus" compatible was originally added for fimc-is only
to ensure the child devices instantiation. The child devices are
now being created by the parent device driver so remove the
"simple-bus" compatible.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Pull thermal managament updates from Zhang Rui:
- Enhance thermal "userspace" governor to export the reason when a
thermal event is triggered and delivered to user space. From Srinivas
Pandruvada
- Introduce a single TSENS thermal driver for the different versions of
the TSENS IP that exist, on different qcom msm/apq SoCs'. Support for
msm8916, msm8960, msm8974 and msm8996 families is also added. From
Rajendra Nayak
- Introduce hardware-tracked trip points support to the device tree
thermal sensor framework. The framework supports an arbitrary number
of trip points. Whenever the current temperature is changed, the trip
points immediately below and above the current temperature are found,
driver callback is invoked to program the hardware to get notified
when either of the two trip points are triggered. Hardware-tracked
trip points support for rockchip thermal driver is also added at the
same time. From Sascha Hauer, Caesar Wang
- Introduce a new thermal driver, which enables TMU (Thermal Monitor
Unit) on QorIQ platform. From Jia Hongtao
- Introduce a new thermal driver for Maxim MAX77620. From Laxman
Dewangan
- Introduce a new thermal driver for Intel platforms using WhiskeyCove
PMIC. From Bin Gao
- Add mt2701 chip support to MTK thermal driver. From Dawei Chien
- Enhance Tegra thermal driver to enable soctherm node and set
"critical", "hot" trips, for Tegra124, Tegra132, Tegra210. From Wei
Ni
- Add resume support for tango thermal driver. From Marc Gonzalez
- several small fixes and improvements for rockchip, qcom, imx, rcar,
mtk thermal drivers and thermal core code. From Caesar Wang, Keerthy,
Rocky Hao, Wei Yongjun, Peter Robinson, Bui Duc Phuc, Axel Lin, Hugh
Kang
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (48 commits)
thermal: int3403: Process trip change notification
thermal: int340x: New Interface to read trip and notify
thermal: user_space gov: Add additional information in uevent
thermal: Enhance thermal_zone_device_update for events
arm64: tegra: set hot trips for Tegra210
arm64: tegra: set critical trips for Tegra210
arm64: tegra: add soctherm node for Tegra210
arm64: tegra: set hot trips for Tegra132
arm64: tegra: set critical trips for Tegra132
arm64: tegra: use tegra132-soctherm for Tegra132
arm: tegra: set hot trips for Tegra124
arm: tegra: set critical trips for Tegra124
thermal: tegra: add hw-throttle for Tegra132
thermal: tegra: add hw-throttle function
of: Add bindings of hw throttle for Tegra soctherm
thermal: mtk_thermal: Check return value of devm_thermal_zone_of_sensor_register
thermal: Add Mediatek thermal driver for mt2701.
dt-bindings: thermal: Add binding document for Mediatek thermal controller
thermal: max77620: Add thermal driver for reporting junction temp
thermal: max77620: Add DT binding doc for thermal driver
...
Pull drm updates from Dave Airlie:
"Core:
- Fence destaging work
- DRIVER_LEGACY to split off legacy drm drivers
- drm_mm refactoring
- Splitting drm_crtc.c into chunks and documenting better
- Display info fixes
- rbtree support for prime buffer lookup
- Simple VGA DAC driver
Panel:
- Add Nexus 7 panel
- More simple panels
i915:
- Refactoring GEM naming
- Refactored vma/active tracking
- Lockless request lookups
- Better stolen memory support
- FBC fixes
- SKL watermark fixes
- VGPU improvements
- dma-buf fencing support
- Better DP dongle support
amdgpu:
- Powerplay for Iceland asics
- Improved GPU reset support
- UVD/VEC powergating support for CZ/ST
- Preinitialised VRAM buffer support
- Virtual display support
- Initial SI support
- GTT rework
- PCI shutdown callback support
- HPD IRQ storm fixes
amdkfd:
- bugfixes
tilcdc:
- Atomic modesetting support
mediatek:
- AAL + GAMMA engine support
- Hook up gamma LUT
- Temporal dithering support
imx:
- Pixel clock from devicetree
- drm bridge support for LVDS bridges
- active plane reconfiguration
- VDIC deinterlacer support
- Frame synchronisation unit support
- Color space conversion support
analogix:
- PSR support
- Better panel on/off support
rockchip:
- rk3399 vop/crtc support
- PSR support
vc4:
- Interlaced vblank timing
- 3D rendering CPU overhead reduction
- HDMI output fixes
tda998x:
- HDMI audio ASoC support
sunxi:
- Allwinner A33 support
- better TCON support
msm:
- DT binding cleanups
- Explicit fence-fd support
sti:
- remove sti415/416 support
etnaviv:
- MMUv2 refactoring
- GC3000 support
exynos:
- Refactoring HDMI DCC/PHY
- G2D pm regression fix
- Page fault issues with wait for vblank
There is no nouveau work in this tree, as Ben didn't get a pull
request in, and he was fighting moving to atomic and adding mst
support, so maybe best it waits for a cycle"
* tag 'drm-for-v4.9' of git://people.freedesktop.org/~airlied/linux: (1412 commits)
drm/crtc: constify drm_crtc_index parameter
drm/i915: Fix conflict resolution from backmerge of v4.8-rc8 to drm-next
drm/i915/guc: Unwind GuC workqueue reservation if request construction fails
drm/i915: Reset the breadcrumbs IRQ more carefully
drm/i915: Force relocations via cpu if we run out of idle aperture
drm/i915: Distinguish last emitted request from last submitted request
drm/i915: Allow DP to work w/o EDID
drm/i915: Move long hpd handling into the hotplug work
drm/i915/execlists: Reinitialise context image after GPU hang
drm/i915: Use correct index for backtracking HUNG semaphores
drm/i915: Unalias obj->phys_handle and obj->userptr
drm/i915: Just clear the mmiodebug before a register access
drm/i915/gen9: only add the planes actually affected by ddb changes
drm/i915: Allow PCH DPLL sharing regardless of DPLL_SDVO_HIGH_SPEED
drm/i915/bxt: Fix HDMI DPLL configuration
drm/i915/gen9: fix the watermark res_blocks value
drm/i915/gen9: fix plane_blocks_per_line on watermarks calculations
drm/i915/gen9: minimum scanlines for Y tile is not always 4
drm/i915/gen9: fix the WaWmMemoryReadLatency implementation
drm/i915/kbl: KBL also needs to run the SAGV code
...
-----BEGIN PGP SIGNATURE-----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=JqCR
-----END PGP SIGNATURE-----
Merge tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation improvements: conversion of all non-DocBook documents
to Sphinx and lots of fixes to the uAPI media book
- New PCI driver for Techwell TW5864 media grabber boards
- New SoC driver for ATMEL Image Sensor Controller
- Removal of some obsolete SoC drivers (s5p-tv driver and soc_camera
drivers)
- Addition of ST CEC driver
- Lots of drivers fixes, improvements and additions
* tag 'media/v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (464 commits)
[media] ttusb_dec: avoid the risk of go past buffer
[media] cx23885: Fix some smatch warnings
[media] si2165: switch to regmap
[media] si2165: use i2c_client->dev instead of i2c_adapter->dev for logging
[media] si2165: Remove legacy attach
[media] cx231xx: attach si2165 driver via i2c_client
[media] cx231xx: Prepare for attaching new style i2c_client DVB demod drivers
[media] cx23885: attach si2165 driver via i2c_client
[media] si2165: support i2c_client attach
[media] si2165: avoid division by zero
[media] rcar-vin: add R-Car gen2 fallback compatibility string
[media] lgdt3306a: remove 20*50 msec unnecessary timeout
[media] cx25821: Remove deprecated create_singlethread_workqueue
[media] cx25821: Drop Freeing of Workqueue
[media] cxd2841er: force 8MHz bandwidth for DVB-C if specified bw not supported
[media] redrat3: hardware-specific parameters
[media] redrat3: remove hw_timeout member
[media] cxd2841er: BER and SNR reading for ISDB-T
[media] dvb-usb: avoid link error with dib3000m{b,c|
[media] dvb-usb: split out common parts of dibusb
...
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been
merged for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and
usb driver changes are required and included here, and also
the clk tree changes.
- The Allwinner platforms have seen a large-scale change to their
clk drivers and the dts file updates must come after that.
This includes the newly added Nextthing GR8 platform, which is
derived from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't
added until just before the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OmAu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
These are as usual a very large number of mostly boring updates to
enable devices in existing machines, or to fix minor bugs. Notably,
an ongoing treewide effort to fix warnings caused by an update to the
device tree compiler. These are enabled with "make W=1" at the moment
but can hopefully become the default once all issues have been addressed.
No new SoC platform is added this time around (Armada 395 and Orion
mv88f5181 are slight variations of existing ones), but a significant
number of new dts files are added, which I list by platform:
- Allwinner: Empire Electronix M712 and iNet d978 Rev2 tablets;
Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E,
Orange Pi Lite, Olimex A33-Olinuxino, and Nano Pi Neo
single-board computers
- ARM Realview: all supported machines (ported from board files)
- Broadcom: BCM958525er, BCM958522er, BCM988312hr, BCM958623hr and
BCM958622hr reference boards for Northstar platform;
Raspberry Pi Zero single-board computer
- Marvell EBU: Netgear WNR854T router (ported from board file);
Armada 395 SoC platform and GP board
Armada 390 DB development board
- NXP i.MX: imx7s Warp7 reference board;
Gateworks Ventana GW553x single-board computer,
Technologic Systems TS-4900 and
Engicam IMX6UL GEA M6UL computer-on-module,
Inverse Path USB armory board
- Qualcomm: LG Nexus 5 Phone
- Renesas: r8a7792/wheat and r7s72100/rskrza1 development boards
- Rockchip: Rockchip RK3288 Fennec reference board;
Firefly RK3288 Reload platform
- ST Microelectronics STi: B2260 (96boards) single-board computer
- TI Davinci: OMAP-L138 LCDK Development kit
- TI OMAP: beagleboard-x15 rev B1 single-board computer
Conflicts: vendor-prefixes.txt has conflicting additions, keep all of
them in alphabetical order.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/gg/
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Arnd Bergmann:
"These are as usual a very large number of mostly boring updates to
enable devices in existing machines, or to fix minor bugs. Notably, an
ongoing treewide effort to fix warnings caused by an update to the
device tree compiler. These are enabled with "make W=1" at the moment
but can hopefully become the default once all issues have been
addressed.
No new SoC platform is added this time around (Armada 395 and Orion
mv88f5181 are slight variations of existing ones), but a significant
number of new dts files are added, which I list by platform:
- Allwinner: Empire Electronix M712 and iNet d978 Rev2 tablets,
Orange Pi PC Plus, Orange Pi 2, Orange Pi Plus 2E, Orange Pi Lite,
Olimex A33-Olinuxino, and Nano Pi Neo single-board computers
- ARM Realview: all supported machines (ported from board files)
- Broadcom: BCM958525er, BCM958522er, BCM988312hr, BCM958623hr and
BCM958622hr reference boards for Northstar platform, Raspberry Pi
Zero single-board computer
- Marvell EBU: Netgear WNR854T router (ported from board file),
Armada 395 SoC platform and GP board Armada 390 DB development
board
- NXP i.MX: imx7s Warp7 reference board, Gateworks Ventana GW553x
single-board computer, Technologic Systems TS-4900 and Engicam
IMX6UL GEA M6UL computer-on-module, Inverse Path USB armory board
- Qualcomm: LG Nexus 5 Phone
- Renesas: r8a7792/wheat and r7s72100/rskrza1 development boards
- Rockchip: Rockchip RK3288 Fennec reference board, Firefly RK3288
Reload platform
- ST Microelectronics STi: B2260 (96boards) single-board computer
- TI Davinci: OMAP-L138 LCDK Development kit
- TI OMAP: beagleboard-x15 rev B1 single-board computer"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (390 commits)
ARM: dts: sony-nsz-gs7: add missing unit name to /memory node
ARM: dts: chromecast: add missing unit name to /memory node
ARM: dts: berlin2q-marvell-dmp: add missing unit name to /memory node
ARM: dts: berlin2: Add missing unit name to /soc node
ARM: dts: berlin2cd: Add missing unit name to /soc node
ARM: dts: berlin2q: Add missing unit name to /soc node
ARM: dts: berlin2: Remove skeleton.dtsi inclusion
ARM: dts: berlin2cd: Remove skeleton.dtsi inclusion
ARM: dts: berlin2q: Remove skeleton.dtsi inclusion
arm: dts: berlin2q: enable all wdt nodes unconditionally
arm: dts: berlin2: enable all wdt nodes unconditionally
ARM: dts: omap5-igep0050.dts: Use tabs for indentation
ARM: dts: Fix igepv5 power button GPIO direction
ARM: dts: am335x-evmsk: Add blue-and-red-wiring -property to lcdc node
ARM: dts: am335x-evmsk: Whitespace cleanup of lcdc related nodes
ARM: dts: am335x-evm: Add blue-and-red-wiring -property to lcdc node
ARM: dts: s3c64xx: Use macros for pinctrl configuration
ARM: dts: s3c2416: Use macros for pinctrl configuration
ARM: dts: s5pv210: Use macros for pinctrl configuration
ARM: dts: s3c64xx: Use common macros for pinctrl configuration
...
Driver updates for ARM SoCs, including a couple of newly added drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for the
EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=GvTq
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
Pull ARM updates from Russell King:
- Correct ARMs dma-mapping to use the correct printk format strings.
- Avoid defining OBJCOPYFLAGS globally which upsets lkdtm rodata
testing.
- Cleanups to ARMs asm/memory.h include.
- L2 cache cleanups.
- Allow flat nommu binaries to be executed on ARM MMU systems.
- Kernel hardening - add more read-only after init annotations,
including making some kernel vdso variables const.
- Ensure AMBA primecell clocks are appropriately defaulted.
- ARM breakpoint cleanup.
- Various StrongARM 11x0 and companion chip (SA1111) updates to bring
this legacy platform to use more modern APIs for (eg) GPIOs and
interrupts, which will allow us in the future to reduce some of the
board-level driver clutter and elimate function callbacks into board
code via platform data. There still appears to be interest in these
platforms!
- Remove the now redundant secure_flush_area() API.
- Module PLT relocation optimisations. Ard says: This series of 4
patches optimizes the ARM PLT generation code that is invoked at
module load time, to get rid of the O(n^2) algorithm that results in
pathological load times of 10 seconds or more for large modules on
certain STB platforms.
- ARMv7M cache maintanence support.
- L2 cache PMU support
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (35 commits)
ARM: sa1111: provide to_sa1111_device() macro
ARM: sa1111: add sa1111_get_irq()
ARM: sa1111: clean up duplication in IRQ chip implementation
ARM: sa1111: implement a gpio_chip for SA1111 GPIOs
ARM: sa1111: move irq cleanup to separate function
ARM: sa1111: use devm_clk_get()
ARM: sa1111: use devm_kzalloc()
ARM: sa1111: ensure we only touch RAB bus type devices when removing
ARM: 8611/1: l2x0: add PMU support
ARM: 8610/1: V7M: Add dsb before jumping in handler mode
ARM: 8609/1: V7M: Add support for the Cortex-M7 processor
ARM: 8608/1: V7M: Indirect proc_info construction for V7M CPUs
ARM: 8607/1: V7M: Wire up caches for V7M processors with cache support.
ARM: 8606/1: V7M: introduce cache operations
ARM: 8605/1: V7M: fix notrace variant of save_and_disable_irqs
ARM: 8604/1: V7M: Add support for reading the CTR with read_cpuid_cachetype()
ARM: 8603/1: V7M: Add addresses for mem-mapped V7M cache operations
ARM: 8602/1: factor out CSSELR/CCSIDR operations that use cp15 directly
ARM: kernel: avoid brute force search on PLT generation
ARM: kernel: sort relocation sections before allocating PLTs
...
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX8Zc4AAoJEHm+PkMAQRiGQG8H/2Hd4IwJh75snGY5LAiWt6ra
kGM/SobvLAMtcoxXCeHqf2bZrxa2Zz9tnEzhuLMGaf9a3l79xHa8YumK5KS1JPGV
6lZBvuPi8BIyT0cpYH000e5ehHfhP6pSGJKZ2EuLv43HcBeVZEGAf3/8jSAlNA15
bwFy2ZEkwJGThbnT6au0Y3s9h8LcNjtllu9hjfb+/9oNGvp8r4QhdVodIqIQ4cv6
SeUfv7Pn2LZDMCSaTP9bh2KaR4dwYZHFsVe75x2wND5Sfq7DVBBfFkAoV/RwJDTM
gBc3PNnmzb/tix6ohOrSQnSiGsXv1uASxvHH3RD2zG6g7Aj9Eq/+Z7ZdPu2+o+U=
=U+ef
-----END PGP SIGNATURE-----
Merge tag 'v4.8' into patchwork
Linux 4.8
* tag 'v4.8': (1761 commits)
Linux 4.8
ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
MIPS: CM: Fix mips_cm_max_vp_width for non-MT kernels on MT systems
include/linux/property.h: fix typo/compile error
ocfs2: fix deadlock on mmapped page in ocfs2_write_begin_nolock()
mm: workingset: fix crash in shadow node shrinker caused by replace_page_cache_page()
MAINTAINERS: Switch to kernel.org email address for Javi Merino
x86/entry/64: Fix context tracking state warning when load_gs_index fails
x86/boot: Initialize FPU and X86_FEATURE_ALWAYS even if we don't have CPUID
x86/vdso: Fix building on big endian host
x86/boot: Fix another __read_cr4() case on 486
sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock
sctp: change to check peer prsctp_capable when using prsctp polices
sctp: remove prsctp_param from sctp_chunk
sctp: move sent_count to the memory hole in sctp_chunk
tg3: Avoid NULL pointer dereference in tg3_io_error_detected()
x86/init: Fix cr4_init_shadow() on CR4-less machines
MIPS: Fix detection of unsupported highmem with cache aliases
MIPS: Malta: Fix IOCU disable switch read for MIPS64
MIPS: Fix BUILD_ROLLBACK_PROLOGUE for microMIPS
...
- Add support for sending commands during data transfer
- Erase/discard/trim improvements
- Improved error handling
- Extend sysfs with SD status register
- Document info about the vmmc/vmmcq regulators
- Extend pwrseq-simple to manage an optional post-power-on-delay
- Some various minor improvements and cleanups
MMC host:
- dw_mmc: Add reset support
- dw_mmc: Return -EILSEQ for EBE and SBE error
- dw_mmc: Some cleanups
- dw_mmc-k3: Add UHS-I support Hisilicon Hikey
- tmio: Add eMMC support
- sh_mobile_sdhi: Add r8a7796 support
- sunxi: Don't use sample clocks for sun4i/sun5i
- sunxi: Add support for A64 mmc controller
- sunxi: Some cleanups and improvements
- sdhci: Support for sending commands during data transfer
- sdhci: Do not allow tuning procedure to be interrupted
- sdhci-pci: Enable SD/SDIO on Merrifield
- sdhci-pci|acpi: Enable MMC_CAP_CMD_DURING_TFR
- sdhci-pci: Some cleanups
- sdhci-of-arasan: Set controller to test mode when no CD bit
- sdhci-of-arasan: Some fixes for clocks and phys
- sdhci-brcmstb: Don't use ADMA 64-bit when not supported
- sdhci-tegra: Mark 64-bit DMA broken on Tegra124
- sdhci-esdhc-imx: Fixups related to data timeouts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=b0/p
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.9' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
MMC core:
- Add support for sending commands during data transfer
- Erase/discard/trim improvements
- Improved error handling
- Extend sysfs with SD status register
- Document info about the vmmc/vmmcq regulators
- Extend pwrseq-simple to manage an optional post-power-on-delay
- Some various minor improvements and cleanups
MMC host:
- dw_mmc: Add reset support
- dw_mmc: Return -EILSEQ for EBE and SBE error
- dw_mmc: Some cleanups
- dw_mmc-k3: Add UHS-I support Hisilicon Hikey
- tmio: Add eMMC support
- sh_mobile_sdhi: Add r8a7796 support
- sunxi: Don't use sample clocks for sun4i/sun5i
- sunxi: Add support for A64 mmc controller
- sunxi: Some cleanups and improvements
- sdhci: Support for sending commands during data transfer
- sdhci: Do not allow tuning procedure to be interrupted
- sdhci-pci: Enable SD/SDIO on Merrifield
- sdhci-pci|acpi: Enable MMC_CAP_CMD_DURING_TFR
- sdhci-pci: Some cleanups
- sdhci-of-arasan: Set controller to test mode when no CD bit
- sdhci-of-arasan: Some fixes for clocks and phys
- sdhci-brcmstb: Don't use ADMA 64-bit when not supported
- sdhci-tegra: Mark 64-bit DMA broken on Tegra124
- sdhci-esdhc-imx: Fixups related to data timeouts
* tag 'mmc-v4.9' of git://git.linaro.org/people/ulf.hansson/mmc: (68 commits)
mmc: dw_mmc: remove the deprecated "supports-highspeed" property
mmc: dw_mmc: minor cleanup for dw_mci_adjust_fifoth
mmc: dw_mmc: use macro to define ring buffer size
mmc: dw_mmc: fix misleading error print if failing to do DMA transfer
mmc: dw_mmc: avoid race condition of cpu and IDMAC
mmc: dw_mmc: split out preparation of desc for IDMAC32 and IDMAC64
mmc: core: don't try to switch block size for dual rate mode
mmc: sdhci-of-arasan: Set controller to test mode when no CD bit
dt: sdhci-of-arasan: Add device tree option xlnx, fails-without-test-cd
mmc: tmio: add eMMC support
mmc: rtsx_usb: use new macro for R1 without CRC
mmc: rtsx_pci: use new macro for R1 without CRC
mmc: add define for R1 response without CRC
mmc: card: do away with indirection pointer
mmc: sdhci-acpi: Set MMC_CAP_CMD_DURING_TFR for Intel eMMC controllers
mmc: sdhci-pci: Set MMC_CAP_CMD_DURING_TFR for Intel eMMC controllers
mmc: sdhci: Support cap_cmd_during_tfr requests
mmc: mmc_test: Add tests for sending commands during transfer
mmc: core: Add support for sending commands during data transfer
mmc: sdhci-brcmstb: Fix incorrect capability
...
buffers (Thor Thayer)
* Split the memory controller part out of mpc85xx and share it with a
* new Freescale ARM Layerscape driver (York Sun)
* amd64_edac fixes (Yazen Ghannam)
* Misc cleanups, refactoring and fixes all over the place
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJX80EwAAoJEBLB8Bhh3lVKWwYP/1bbODQ7o+XhO8IaCDffYk30
8y4WdSnI0/QcP8JbSvFA7y6Zn4L0BbrbYhKLRDAg9c34V2bMaqonCnkDtT6YatUb
6l0H/hQ/Cah9AOm5PJLYg6O9s+ZBT8zA5b+F2Z9kUsuB6LSnVhp9skNrH6KPlm0U
4pFaLnHQenQPZbuRCfRxPU49ZuKtBZtQDkJLJlHXwn7e1qZy2Q4tMnnEtsY6U2ea
t3Hj+F8g+cdoiTQXOceCcOTR8GqDI6szgzn7vpXAGYvljBndszauAkxO7by79jg1
I8AQfgwoBF5CYL2Q0pzT1maHmmG2sydeRAHIvhmGxiEfFz1abWhriXbS33c32q8a
iFiVMAUIaSKpB/sB+5w5ymuBctI1mX5EQVW+8Xl2Gxt+olnhdJMocHnvQdYkfsYm
Ka8LcbaiK6ZQTbs/cIMOc2paE0AFPu5uXKHCPeZlhQAxOBvSPuDAv0+qUB/of5Uq
1SPidtsTmCI7X2hrdHAH9hLEkSjq68v3kqL5YnZL3H4gA3WohQEmX9ybjk097Kus
WWEhdi/PSFX0qQKotMUUDuxfNcKI6PZH9p+i2dN6tNCkiTDdb0Eo5lCXN7RVVhvq
qfE0Fcc4uDzh5MUS5jT58MWpA1cfdu9jbAf2BwFIU/poJcaeqy/SMyzCL+1D2/u6
dmDAtQbKUUwiltB8QzQd
=pcI8
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"A lot of movement in the EDAC tree this time around, coarse summary
below:
- Altera Arria10 enablement of NAND, DMA, USB, QSPI and SD-MMC FIFO
buffers (Thor Thayer)
- split the memory controller part out of mpc85xx and share it with a
new Freescale ARM Layerscape driver (York Sun)
- amd64_edac fixes (Yazen Ghannam)
- misc cleanups, refactoring and fixes all over the place"
* tag 'edac_for_4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: (37 commits)
EDAC, altera: Add IRQ Flags to disable IRQ while handling
EDAC, altera: Correct EDAC IRQ error message
EDAC, amd64: Autoload module using x86_cpu_id
EDAC, sb_edac: Remove NULL pointer check on array pci_tad
EDAC: Remove NO_IRQ from powerpc-only drivers
EDAC, fsl_ddr: Fix error return code in fsl_mc_err_probe()
EDAC, fsl_ddr: Add entry to MAINTAINERS
EDAC: Move Doug Thompson to CREDITS
EDAC, I3000: Orphan driver
EDAC, fsl_ddr: Replace simple_strtoul() with kstrtoul()
EDAC, layerscape: Add Layerscape EDAC support
EDAC, fsl_ddr: Fix IRQ dispose warning when module is removed
EDAC, fsl_ddr: Add support for little endian
EDAC, fsl_ddr: Add missing DDR DRAM types
EDAC, fsl_ddr: Rename macros and names
EDAC, fsl-ddr: Separate FSL DDR driver from MPC85xx
EDAC, mpc85xx: Replace printk() with pr_* format
EDAC, mpc85xx: Drop setting/clearing RFXE bit in HID1
EDAC, altera: Rename MC trigger to common name
EDAC, altera: Rename device trigger to common name
...
Pull irq updates from Thomas Gleixner:
"The irq departement proudly presents:
- A rework of the core infrastructure to optimally spread interrupt
for multiqueue devices. The first version was a bit naive and
failed to take thread siblings and other details into account.
Developed in cooperation with Christoph and Keith.
- Proper delegation of softirqs to ksoftirqd, so if ksoftirqd is
active then no further softirq processsing on interrupt return
happens. Otherwise we try to delegate and still run another batch
of network packets in the irq return path, which then tries to
delegate to ksoftirqd .....
- A proper machine parseable sysfs based alternative for
/proc/interrupts.
- ACPI support for the GICV3-ITS and ARM interrupt remapping
- Two new irq chips from the ARM SoC zoo: STM32-EXTI and MVEBU-PIC
- A new irq chip for the JCore (SuperH)
- The usual pile of small fixlets in core and irqchip drivers"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (42 commits)
softirq: Let ksoftirqd do its job
genirq: Make function __irq_do_set_handler() static
ARM/dts: Add EXTI controller node to stm32f429
ARM/STM32: Select external interrupts controller
drivers/irqchip: Add STM32 external interrupts support
Documentation/dt-bindings: Document STM32 EXTI controller bindings
irqchip/mips-gic: Use for_each_set_bit to iterate over local IRQs
pci/msi: Retrieve affinity for a vector
genirq/affinity: Remove old irq spread infrastructure
genirq/msi: Switch to new irq spreading infrastructure
genirq/affinity: Provide smarter irq spreading infrastructure
genirq/msi: Add cpumask allocation to alloc_msi_entry
genirq: Expose interrupt information through sysfs
irqchip/gicv3-its: Use MADT ITS subtable to do PCI/MSI domain initialization
irqchip/gicv3-its: Factor out PCI-MSI part that might be reused for ACPI
irqchip/gicv3-its: Probe ITS in the ACPI way
irqchip/gicv3-its: Refactor ITS DT init code to prepare for ACPI
irqchip/gicv3-its: Cleanup for ITS domain initialization
PCI/MSI: Setup MSI domain on a per-device basis using IORT ACPI table
ACPI: Add new IORT functions to support MSI domain handling
...
The change adds a new device node with description of generic SRAM
on-chip memory found on NXP LPC32xx SoC series and connected to AHB
matrix slave port 3.
Note that NXP LPC3220 SoC has 128KiB of SRAM memory, the other
LPC3230, LPC3240 and LPC3250 SoCs all have 256KiB SRAM space,
in the shared DTSI file this change specifies 128KiB SRAM size.
Also it's worth to mention that the SRAM area contains of 64KiB banks,
2 banks on LPC3220 and 4 banks on the other SoCs from the series, and
all SRAM banks but the first one have independent power controls,
the description of this feature will be added with the introduction of
power domains for the SoC series.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM fixes from Russell King:
"Three relatively small fixes for ARM:
- Roger noticed that dma_max_pfn() was calculating the upper limit
wrongly, by adding the PFN offset of memory twice.
- A fix from Robin to correct parsing of MPIDR values when the
address size is larger than one BE32 unit.
- A fix from Srinivas to ensure that we do not rely on the boot
loader (or previous Linux kernel) setting the translation table
base register a certain way in the decompressor, which can lead to
crashes"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8618/1: decompressor: reset ttbcr fields to use TTBR0 on ARMv7
ARM: 8617/1: dma: fix dma_max_pfn()
ARM: 8616/1: dt: Respect property size when parsing CPUs
If the bootloader uses the long descriptor format and jumps to
kernel decompressor code, TTBCR may not be in a right state.
Before enabling the MMU, it is required to clear the TTBCR.PD0
field to use TTBR0 for translation table walks.
The commit dbece45894 ("ARM: 7501/1: decompressor:
reset ttbcr for VMSA ARMv7 cores") does the reset of TTBCR.N, but
doesn't consider all the bits for the size of TTBCR.N.
Clear TTBCR.PD0 field and reset all the three bits of TTBCR.N to
indicate the use of TTBR0 and the correct base address width.
Fixes: dbece45894 ("ARM: 7501/1: decompressor: reset ttbcr for VMSA ARMv7 cores")
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes the following DTC warning with W=1:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch fixes the following DTC warning with W=1:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch fixes the following DTC warning with W=1:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch fixes the following DTC warning with W=1:
"Node /soc has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch fixes the following DTC warning with W=1:
"Node /soc has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch fixes the following DTC warning with W=1:
"Node /soc has a reg or ranges property, but no unit name"
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
As noted in [1], "there are a number of problems with skeleton.dtsi,
and it would be prefereable to remove it entirely." This patch is to
remove skeleton.dtsi inclusion from berlin2.
[1] http://www.spinics.net/lists/arm-kernel/msg528080.html
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
As noted in [1], "there are a number of problems with skeleton.dtsi,
and it would be prefereable to remove it entirely." This patch is to
remove skeleton.dtsi inclusion from berlin2cd.
[1] http://www.spinics.net/lists/arm-kernel/msg528080.html
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
As noted in [1], "there are a number of problems with skeleton.dtsi,
and it would be prefereable to remove it entirely." This patch is to
remove skeleton.dtsi inclusion from berlin2q.
[1] http://www.spinics.net/lists/arm-kernel/msg528080.html
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
After commit f29a72c24a ("watchdog: dw_wdt: Convert to use watchdog
infrastructure"), the dw_wdt driver can support multiple variants, so
unconditionally enable all dw_wdt nodes now.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
After commit f29a72c24a ("watchdog: dw_wdt: Convert to use watchdog
infrastructure"), the dw_wdt driver can support multiple variants, so
unconditionally enable all dw_wdt nodes now.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJX6H4uAAoJEHm+PkMAQRiG5sMH/3yzrMiUCSokdS+cvY+jgKAG
JS58JmRvBPz2mRaU3MRPBGRDeCz/Nc9LggL2ZcgM+E1ZYirlYyQfIED3lkqk5R07
kIN1wmb+kQhXyU4IY3fEX7joqyKC6zOy4DUChPkBQU0/0+VUmdVmcJvsuPlnMZtf
g95m0BdYTui+eDezASRqOEp3Lb5ONL4c3ao4yBP0LHF033ctj3VJQiyi5uERPZJ0
5e6Mo7Wxn78t9WqJLQAiEH46kTwT2plNlxf3XXqTenfIdbWhqE873HPGeSMa3VQV
VywXTpCpSPQsA8BYg66qIbebdKOhs9MOviHVfqDtwQlvwhjlBDya0gNHfI5fSy4=
=Y/L5
-----END PGP SIGNATURE-----
Merge tag 'v4.8-rc8' into drm-next
Linux 4.8-rc8
There was a lot of fallout in the imx/amdgpu/i915 drivers, so backmerge
it now to avoid troubles.
* tag 'v4.8-rc8': (1442 commits)
Linux 4.8-rc8
fault_in_multipages_readable() throws set-but-unused error
mm: check VMA flags to avoid invalid PROT_NONE NUMA balancing
radix tree: fix sibling entry handling in radix_tree_descend()
radix tree test suite: Test radix_tree_replace_slot() for multiorder entries
fix memory leaks in tracing_buffers_splice_read()
tracing: Move mutex to protect against resetting of seq data
MIPS: Fix delay slot emulation count in debugfs
MIPS: SMP: Fix possibility of deadlock when bringing CPUs online
mm: delete unnecessary and unsafe init_tlb_ubc()
huge tmpfs: fix Committed_AS leak
shmem: fix tmpfs to handle the huge= option properly
blk-mq: skip unmapped queues in blk_mq_alloc_request_hctx
MIPS: Fix pre-r6 emulation FPU initialisation
arm64: kgdb: handle read-only text / modules
arm64: Call numa_store_cpu_info() earlier.
locking/hung_task: Fix typo in CONFIG_DETECT_HUNG_TASK help text
nvme-rdma: only clear queue flags after successful connect
i2c: qup: skip qup_i2c_suspend if the device is already runtime suspended
perf/core: Limit matching exclusive events to one PMU
...
Enable throttle function for SOC_THERM.
Set "hot" trips for cpu and gpu thermal zones, which
can trigger the SOC_THERM hardware throttle.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Set general "critical" trip temperatures for cpu, gpu, mem and pllx
thermal zones for all Tegra124 platform, these trips can trigger
shut down or reset.
Tegra124 Jetson TK1 was already set "critical" trips before, so it
can overwrite the general values.
Signed-off-by: Wei Ni <wni@nvidia.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Use the new sun7i-a20-mmc compatible for the mmc controllers on sun7i
and newer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the tilcdc quirks:
- Fix typo with recent beagleboard-x15 changes for mmc2_pins_default
- Add am335x blue-and-red-wiring quirk as specified in the binding in
Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt. Also
fix up the whitespace formatting for am335x-evmsk.
- Fix for recent igepv5 power button for GPIO_ACTIVE_LOW. Also fix
up the whitespace formatting for the button
-----BEGIN PGP SIGNATURE-----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=14Zw
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.9/dt-pt3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "few minor fixes for omap dts files for v4.9 merge window"
Few fixes for omap dts files for v4.9 merge window. Let's also add
the tilcdc quirks:
- Fix typo with recent beagleboard-x15 changes for mmc2_pins_default
- Add am335x blue-and-red-wiring quirk as specified in the binding in
Documentation/devicetree/bindings/display/tilcdc/tilcdc.txt. Also
fix up the whitespace formatting for am335x-evmsk.
- Fix for recent igepv5 power button for GPIO_ACTIVE_LOW. Also fix
up the whitespace formatting for the button
* tag 'omap-for-v4.9/dt-pt3-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap5-igep0050.dts: Use tabs for indentation
ARM: dts: Fix igepv5 power button GPIO direction
ARM: dts: am335x-evmsk: Add blue-and-red-wiring -property to lcdc node
ARM: dts: am335x-evmsk: Whitespace cleanup of lcdc related nodes
ARM: dts: am335x-evm: Add blue-and-red-wiring -property to lcdc node
ARM: dts: am57xx-beagle-x15-common: Fix wrong pinctrl selection for mmc2
Here is a bunch of late changes for the 4.9 merge window, mostly:
- Added a bunch of touchscreens nodes to tablets
- Added support for the AXP806 PMIC found in the A80 boards
- Enabled a few pinmux options for the H3
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YfLG
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.9-3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/late
Pull "Allwinner DT changes for 4.9, late edition" from Maxime Ripard:
Here is a bunch of late changes for the 4.9 merge window, mostly:
- Added a bunch of touchscreens nodes to tablets
- Added support for the AXP806 PMIC found in the A80 boards
- Enabled a few pinmux options for the H3
* tag 'sunxi-dt-for-4.9-3' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
Add a dt node describing the mma7660 accelerometer on the
polaroid-mid2407pxe03 tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
UART1 is connected to the bluetooth part of RTL8723BS WiFi/BT combo card
on iNet D978 Rev2 board.
Enable the UART1 to make it possible to use the modified hciattach by
Realtek to drive the BT part of RTL8723BS.
On the board no r_uart pins are found now (the onboard RX/TX pins are
wired to PF2/PF4, which is muxed with mmc0), so also disabled it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The UART1 at PG (PG6, PG7, PG8, PG9) is, in the Allwinner's reference
tablet design of A23/33, used to connect to UART Bluetooth cards.
Add the pinmux for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These peripherals can only be muxed to these pins, so they are
associated in the DTSI instead of the board files. This makes it very
easy to enable them using overlays or u-boot commands:
=> fdt set /soc/i2c@01c2ac00 status okay
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These are the only possible pins for these peripherals according to the
datasheet.
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These H3 boards all expose UART1-3 on their expansion header. Since
other functions can be muxed to these pins, they are explicitly
disabled. To enable them, one could use DT overlays or U-boot commands:
=> fdt set /soc/serial@01c28c00 status okay
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This was done to make UART1-3 on H3 consistent, and less complicated to
enable UART1-3 on the breakout header on the several H3 board (notably
Orange Pi's). This patch adds a bit of complexity for the existing Banana
Pi, which already had the RTS/CTS associated on UART1.
The RTS/CTS for UART2-3 could be defined in the same way, but since
there is no actual use case for them at the moment, they are left out.
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These are the pinmux definitions for UART2-3 on H3. These UARTs can only
be muxed to these pins, so _a and @0 do not really make sense. I have
left out RTS/CTS, since these are rarely used. These can easily be
enabled using an additional pinmux set.
Signed-off-by: Jorik Jonker <jorik@kippendief.biz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
