* Stop using nand_release(), patched all drivers.
* Give more information about the ECC weakness when not matching the
chip's requirement.
* MAINTAINERS updates.
* Support emulated SLC mode on MLC NANDs.
* Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
* Take check_only into account.
* Add an invalid ECC mode to discriminate with valid ones.
* Return an enum from of_get_nand_ecc_algo().
* Drop OOB_FIRST placement scheme.
* Introduce nand_extract_bits().
* Ensure a consistent bitflips numbering.
* BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
* Fix nand_gpio_waitrdy().
* Propage CS selection to sub operations.
* Add a NAND_NO_BBM_QUIRK flag.
* Give the possibility to verify a read operation is supported.
* Add a helper to check supported operations.
* Avoid indirect access to ->data_buf().
* Rename the use_bufpoi variables.
* Fix comments about the use of bufpoi.
* Rename a NAND chip option.
* Reorder the nand_chip->options flags.
* Translate obscure bitfields into readable macros.
* Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
* Fixed many error paths.
* Arasan
- New driver
* Au1550nd:
- Various cleanups
- Migration to ->exec_op()
* brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
* Cadence
- Make cadence_nand_attach_chip static.
* Cafe:
- Set the NAND_NO_BBM_QUIRK flag
* cmx270:
- Remove this controller driver.
* cs553x:
- Misc cleanup
- Migration to ->exec_op()
* Davinci:
- Misc cleanup.
- Migration to ->exec_op()
* Denali:
- Add more delays before latching incoming data
* Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
* Fsmc:
- Change to non-atomic bit operations.
* GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
* Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
* Marvell:
- Misc cleanup and small fixes
* Nandsim:
- Fix the error paths, driver wide.
* Omap_elm:
- Fix runtime PM imbalance.
* STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAl7TdZMACgkQJWrqGEe9
VoRthQgAttWsImXpEUa8C8CXvPhjpb6uZ7QYM4PSE0bheuVi7ivoDPyYWopno30h
R6UntGbsBqPyvDFDUxUEvyvn5F0JQK1dLif+7X0Ki5on6LkYdEuanHaSMZmSIXD8
atNhLVO1FeD3EulN8Dw9hGy6OrNT8O2bESbiJrCpOk9s6yAPINhKqZVJsyShcTs5
tc94/J0DIF7og8cdH4wYoz+AWw0WaHvPsn5VWnTy08gk7dB7hsq/DeftZmrJLL0g
B7Et1pvcLBSNBGBpzS6rEjXb/e3+wdKnNy0AQvrMdEZUzN3h9aY5sCLSFOsFfKQ+
xjxJgmyoKk0C9uCeNaPt8c7gTgAZAA==
=Gz6y
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux into mtd/next
Raw NAND core changes:
* Stop using nand_release(), patched all drivers.
* Give more information about the ECC weakness when not matching the
chip's requirement.
* MAINTAINERS updates.
* Support emulated SLC mode on MLC NANDs.
* Support "constrained" controllers, adapt the core and ONFI/JEDEC
table parsing and Micron's code.
* Take check_only into account.
* Add an invalid ECC mode to discriminate with valid ones.
* Return an enum from of_get_nand_ecc_algo().
* Drop OOB_FIRST placement scheme.
* Introduce nand_extract_bits().
* Ensure a consistent bitflips numbering.
* BCH lib:
- Allow easy bit swapping.
- Rework a little bit the exported function names.
* Fix nand_gpio_waitrdy().
* Propage CS selection to sub operations.
* Add a NAND_NO_BBM_QUIRK flag.
* Give the possibility to verify a read operation is supported.
* Add a helper to check supported operations.
* Avoid indirect access to ->data_buf().
* Rename the use_bufpoi variables.
* Fix comments about the use of bufpoi.
* Rename a NAND chip option.
* Reorder the nand_chip->options flags.
* Translate obscure bitfields into readable macros.
* Timings:
- Fix default values.
- Add mode information to the timings structure.
Raw NAND controller driver changes:
* Fixed many error paths.
* Arasan
- New driver
* Au1550nd:
- Various cleanups
- Migration to ->exec_op()
* brcmnand:
- Misc cleanup.
- Support v2.1-v2.2 controllers.
- Remove unused including <linux/version.h>.
- Correctly verify erased pages.
- Fix Hamming OOB layout.
* Cadence
- Make cadence_nand_attach_chip static.
* Cafe:
- Set the NAND_NO_BBM_QUIRK flag
* cmx270:
- Remove this controller driver.
* cs553x:
- Misc cleanup
- Migration to ->exec_op()
* Davinci:
- Misc cleanup.
- Migration to ->exec_op()
* Denali:
- Add more delays before latching incoming data
* Diskonchip:
- Misc cleanup
- Migration to ->exec_op()
* Fsmc:
- Change to non-atomic bit operations.
* GPMI:
- Use nand_extract_bits()
- Fix runtime PM imbalance.
* Ingenic:
- Migration to exec_op()
- Fix the RB gpio active-high property on qi, lb60
- Make qi_lb60_ooblayout_ops static.
* Marvell:
- Misc cleanup and small fixes
* Nandsim:
- Fix the error paths, driver wide.
* Omap_elm:
- Fix runtime PM imbalance.
* STM32_FMC2:
- Misc cleanups (error cases, comments, timeout valus, cosmetic
changes).
NAND ECC modes (or providers) have their own enumeration but, unlike
their algorithms counterpart, there is no invalid or uninitialized
value to discriminate between an error and having chosen a no-ECC
situation. Add an "invalid" entry for this purpose.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200526195633.11543-7-miquel.raynal@bootlin.com
This scheme has been introduced for the Davinci controller and means
that the OOB area must be read *before* the rest of the data. This has
nothing to do with the ECC in OOB placement as it could be understood
and most importantly, there is no point in having this function out of
the Davinci NAND controller driver. A DT property for this scheme has
been added but never used, even by the Davinci driver which only uses
this scheme to change the default nand_read_page().
Move the main read_page() helper into the Davinci driver and remove
the remaining boilerplate.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Link: https://lore.kernel.org/linux-mtd/20200526195633.11543-4-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Now that all drivers have been converted to do not use nand_release()
anymore, let's remove this helper.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-63-miquel.raynal@bootlin.com
nand_release() basically calls mtd_device_unregister() and
nand_cleanup(). Both helpers should be called after MTD device
registration and NAND scan, respectively. Drop nand_release() and use
the two helpers directly so that they fit the error path and the
labels there.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-12-miquel.raynal@bootlin.com
ns_free() is the helper that is called symmetrically to ns_init() and
so should free the same objects, including the partition names.
Now, callers of ns_free() do not need to free this partition names
themselves.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-11-miquel.raynal@bootlin.com
Many function calls are done this way:
if ((retval = func()) != 0)
return retval;
while we expect in the kernel function calls like:
retval = func();
if (retval)
return retval;
Apply this change where possible and also use "ret" instead of
"retval" in ns_init_module for consistency, as it is only used in this
function.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-5-miquel.raynal@bootlin.com
Some functions are prefixed "nandsim_", others "ns_" and many are
simply not prefixed at all. Make this file consistent by prefixing all
functions by "ns_".
This is a mechanical change. Sometimes the line is a bit reworked as
well to fit the kernel coding style. For instance, there are several
places where displayed strings are cut. When one of this line is
changed because of the naming update, the two parts of the strings
gets concatenated.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200525085851.17682-4-miquel.raynal@bootlin.com
Only v3.3-v5.0 have a different CS0 layout.
Controllers before v3.3 use the same layout for every CS.
Fixes: 27c5b17cd1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522121524.4161539-3-noltari@gmail.com
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522104008.28340-1-dinghao.liu@zju.edu.cn
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200522095139.19653-1-dinghao.liu@zju.edu.cn
Let's convert the driver to exec_op() to have one less driver relying
on the legacy interface.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Tested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519232454.374081-4-boris.brezillon@collabora.com
The rb-gpios semantics was undocumented and qi,lb60 (along with the
ingenic driver) got it wrong. The active state encodes the NAND ready
state, which is high level. Since there's no signal inverter on this
board, it should be active-high. Let's fix that here for older DTs so
we can re-use the generic nand_gpio_waitrdy() helper, and be consistent
with what other drivers do.
Suggested-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519232454.374081-3-boris.brezillon@collabora.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-62-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
There is no real Fixes tag applying here as the use of nand_release()
in this driver predates the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-61-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Stefan Agner <stefan@agner.ch>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-60-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-59-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-58-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
There is no real Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-57-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-56-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-55-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Christophe Kerello <christophe.kerello@st.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-53-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-52-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
There is no real Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense even if this commit is not
introducing any bug.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-51-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-50-miquel.raynal@bootlin.com
nand_release() is supposed be called after MTD device registration.
Here, only nand_scan() happened, so use nand_cleanup() instead.
There is no Fixes tag applying here as the use of nand_release()
in this driver predates by far the introduction of nand_cleanup() in
commit d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
which makes this change possible. However, pointing this commit as the
culprit for backporting purposes makes sense.
Fixes: d44154f969 ("mtd: nand: Provide nand_cleanup() function to free NAND related resources")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-49-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-48-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-47-miquel.raynal@bootlin.com
This helper is not very useful and very often people get confused:
they use nand_release() instead of nand_cleanup().
Let's stop using nand_release() by calling mtd_device_unregister() and
nand_cleanup() directly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Link: https://lore.kernel.org/linux-mtd/20200519130035.1883-46-miquel.raynal@bootlin.com
