The parameter passed to pca9665_reset is adap->data (which is bus driver
specific), not i2c_algp_pca_data *adap. pca9665_reset expects it to be
i2c_algp_pca_data *adap. All other wrappers from the algo call back to
the bus driver, which knows to handle its custom data. Only pca9665_reset
resides inside the algorithm code and does not know how to handle a custom
data structure. This can result in a kernel crash.
Fix by re-factoring pca_reset() from a macro to a function handling chip
specific code, and only call adap->reset_chip() if the chip is not PCA9665.
Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Now that i2c-mux-gpio is able to find the GPIO chip by itself, we can
delegate this task. The great thing here is that i2c-mux-gpio can
defer device probing until the gpio chip is available, so we no longer
depend on the module loading order.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The code instantiating an i2c-mux-gpio platform device doesn't
necessarily know in advance the GPIO pin numbers it wants to use. If
pins are on a GPIO device which gets its base GPIO number assigned
dynamically at run-time, the values can't be hard-coded.
In that case, let the caller tell i2c-mux-gpio the name of the GPIO
chip and the (relative) GPIO pin numbers to use. At probe time, the
i2c-mux-gpio driver will look for the chip and apply the proper offset
to turn relative GPIO pin numbers to absolute GPIO pin numbers.
The same could be (and was so far) done on the caller's end, however
doing it in i2c-mux-gpio has two benefits:
* It avoids duplicating the code on every caller's side (about 30
lines of code.)
* It allows for deferred probing for the muxed part of the I2C bus
only. If finding the GPIO chip is the caller's responsibility, then
deferred probing (if the GPIO chip isn't there yet) will not only
affect the mux and the I2C bus segments behind it, but also the I2C
bus trunk.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Use the devm_kzalloc managed function to stripdown the error and remove
code.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add support for SMBus multiplexing on Asus Z8 motherboard series. On
these boards, the memory slots are behind a GPIO-controlled I2C
multiplexer. Models with 6 or 12 memory slots have 2 segments behind
the multiplexer, while models with 18 memory slots have 3 such
segments.
On these boards, only the memory slots are behind the multiplexer,
so it is possible to keep the autodetection mechanism.
The code is generic enough so it could work on other boards as long as
the multiplexer is controlled by GPIO pins. For other forms of
multiplexing (for example using an I2C device) additional code will be
needed.
Thanks to Asus for providing a board to develop and test this feature,
as well as all the technical information required.
At the moment, the GPIO driver must be loaded before the i2c-i801
driver, but I hope to solve this soon, using deferred probing on
the i2c-mux-gpio side.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The SMBus controller in the VIA VX900 appears to be compatible with
the VIA VX855, so just add the device ID.
This closes kernel bug #43096.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
i2c_dw_xfer_msg is only called internally so it can be static. It
original was, before the driver split. No idea why it was changed at
that time.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Replace printks with pr_<level>s, add pr_fmt()s to replace NAMEs
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Reviewed-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Remove the global dependency of the I2C subsystem on HAS_IOMEM and
move the dependency to the i2c/busses submenu, with an exception for
i2c-stub.
The generic I2C part does not need to have HAS_IOMEM set and thus now
becomes available in UML, so the I2C subsystem can now be used, e.g.
by the i2c-stub driver, for development of I2C device drivers.
[JD: Some adjustments.]
[Heiko Carstens: Keep I2C disabled on S390.]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Converting kzalloc to devm_kzalloc simplifies the code and ensures that the
result, alert, is freed after the irq allocated by the subsequent
devm_request_irq. This in turn ensures that when an interrupt can be
triggered, the alert structure is still available.
The problem of a free after a devm_request_irq was found using the
following semantic match (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2,x,a,b,c,d;
identifier free;
position p1,p2;
@@
devm_request_irq@p1(e1,e2,...,x)
... when any
when != e2 = a
when != x = b
if (...) {
... when != e2 = c
when != x = d
free@p2(...,x,...);
...
return ...;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let I2C bus segments behind multiplexers have a class. This allows for
device auto-detection on these segments. As long as parent segments
don't share the same class, it should be fine.
I implemented support in drivers i2c-mux-gpio and i2c-mux-pca954x. I
left i2c-mux-pca9541 and i2c-mux-pinctrl alone for the moment as I
don't know if this feature makes sense for the use cases of these
drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Korsgaard <peter.korsgaard@barco.com>
Cc: David Daney <david.daney@cavium.com>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
Cc: Rodolfo Giometti <giometti@linux.it>
To avoid name conflicts:
drivers/video/riva/fbdev.c:281:9: sparse: preprocessor token MAX_LEVEL redefined
While at it, also make the other names more consistent and add
parentheses.
[akpm@linux-foundation.org: repair fallout]
[sfr@canb.auug.org.au: IB/mlx4: fix for MAX_ID_MASK to MAX_IDR_MASK name change]
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bernd Petrovitsch <bernd@petrovitsch.priv.at>
Cc: walter harms <wharms@bfs.de>
Cc: Glauber Costa <glommer@parallels.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Roland Dreier <roland@purestorage.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot of
driver/platform shared definitions have gone, such as platform data
structures. They now need to move out to a common location instead,
and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move and
once it settles in, we should be good for quite a while. Sorry for the
overhead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Tc6y
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc multiplatform enablement from Olof Johansson:
"This is a pretty significant branch. It's the introduction of the
first multiplatform support on ARM, and with this (and the later
branch) merged, it is now possible to build one kernel that contains
support for highbank, vexpress, mvebu, socfpga, and picoxcell. More
platforms will be convered over in the next few releases.
Two critical last things had to be done for this to be practical and
possible:
* Today each platform has its own include directory under
mach-<mach>/include/mach/*, and traditionally that is where a lot
of driver/platform shared definitions have gone, such as platform
data structures. They now need to move out to a common location
instead, and this branch moves a large number of those out to
include/linux/platform_data.
* Each platform used to list the device trees to compile for its
boards in mach-<mach>/Makefile.boot.
Both of the above changes will mean that there are some merge
conflicts to come (and some to resolve here). It's a one-time move
and once it settles in, we should be good for quite a while. Sorry
for the overhead."
Fix conflicts as per Olof.
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: add v7 multi-platform defconfig
ARM: msm: Move core.h contents into common.h
ARM: highbank: call highbank_pm_init from .init_machine
ARM: dtb: move all dtb targets to common Makefile
ARM: spear: move platform_data definitions
ARM: samsung: move platform_data definitions
ARM: orion: move platform_data definitions
ARM: vexpress: convert to multi-platform
ARM: initial multiplatform support
ARM: mvebu: move armada-370-xp.h in mach dir
ARM: vexpress: remove dependency on mach/* headers
ARM: picoxcell: remove dependency on mach/* headers
ARM: move all dtb targets out of Makefile.boot
ARM: picoxcell: move debug macros to include/debug
ARM: socfpga: move debug macros to include/debug
ARM: mvebu: move debug macros to include/debug
ARM: vexpress: move debug macros to include/debug
ARM: highbank: move debug macros to include/debug
ARM: move debug macros to common location
ARM: make mach/gpio.h headers optional
...
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck7M
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc driver specific changes from Olof Johansson:
- A long-coming conversion of various platforms to a common LED
infrastructure
- AT91 is moved over to use the newer MCI driver for MMC
- Pincontrol conversions for samsung platforms
- DT bindings for gscaler on samsung
- i2c driver fixes for tegra, acked by i2c maintainer
Fix up conflicts as per Olof.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (48 commits)
drivers: bus: omap_l3: use resources instead of hardcoded irqs
pinctrl: exynos: Fix wakeup IRQ domain registration check
pinctrl: samsung: Uninline samsung_pinctrl_get_soc_data
pinctrl: exynos: Correct the detection of wakeup-eint node
pinctrl: exynos: Mark exynos_irq_demux_eint as inline
pinctrl: exynos: Handle only unmasked wakeup interrupts
pinctrl: exynos: Fix typos in gpio/wkup _irq_mask
pinctrl: exynos: Set pin function to EINT in irq_set_type of GPIO EINTa
drivers: bus: Move the OMAP interconnect driver to drivers/bus/
i2c: tegra: dynamically control fast clk
i2c: tegra: I2_M_NOSTART functionality not supported in Tegra20
ARM: tegra: clock: remove unused clock entry for i2c
ARM: tegra: clock: add connection name in i2c clock entry
i2c: tegra: pass proper name for getting clock
ARM: tegra: clock: add i2c fast clock entry in clock table
ARM: EXYNOS: Adds G-Scaler device from Device Tree
ARM: EXYNOS: Add clock support for G-Scaler
ARM: EXYNOS: Enable pinctrl driver support for EXYNOS4 device tree enabled platform
ARM: dts: Add pinctrl node entries for SAMSUNG EXYNOS4210 SoC
ARM: EXYNOS: skip wakeup interrupt setup if pinctrl driver is used
...
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Len Brown <len.brown@intel.com>
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the samsung include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: Liam Girdwood <lrg@ti.com>
Cc: linux-samsung-soc@vger.kernel.org
Pull i2c embedded fixes from Wolfram Sang:
"The last bunch of (typical) i2c-embedded driver fixes for 3.6.
Also update the MAINTAINERS file to point to my tree since people keep
asking where to find their patches."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: algo: pca: Fix mode selection for PCA9665
MAINTAINERS: fix tree for current i2c-embedded development
i2c: mxs: correctly setup speed for non devicetree
i2c: pnx: Fix read transactions of >= 2 bytes
i2c: pnx: Fix bit definitions
mpc_i2c_stop() only initiates STOP but does not wait for it to
hit the I2C bus. This is a problem when using I2C devices which
uses fairly long clock stretching just before STOP if you also
have an i2c-mux which may switch to another bus before STOP has
been processed.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The code currently always selects turbo mode for PCA9665, no matter which
clock frequency is configured. This is because it compares the clock frequency
against constants reflecting (boundary / 100). Compare against real boundary
frequencies to fix the problem.
Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
As a first step towards migrating davinci platforms to use common clock
framework, replace all instances of clk_enable() with clk_prepare_enable()
and clk_disable() with clk_disable_unprepare(). Until the platform is
switched to use the CONFIG_HAVE_CLK_PREPARE Kconfig variable, this just
adds a might_sleep() call and would work without any issues.
This will make it easy later to switch to common clk based implementation
of clk driver from DaVinci specific driver.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the w90x900 include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the imx include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Sascha Hauer <kernel@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@linux.intel.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Dan Williams <djbw@fb.com>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Javier Martin <javier.martin@vista-silicon.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Platform data for device drivers should be defined in
include/linux/platform_data/*.h, not in the architecture
and platform specific directories.
This moves such data out of the davinci include directories
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: "Ben Dooks" <ben-linux@fluff.org>
Cc: "Wolfram Sang" <w.sang@pengutronix.de>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chris Ball <cjb@laptop.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Liam Girdwood <lrg@ti.com>
Cc: davinci-linux-open-source@linux.davincidsp.com
Tegra I2C driver enables the fast clock during initialization
and does not disable till driver removed.
Enable this clock before transfer and disable after transfer done.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra20 i2c controller does not support the continue transfer
which implements the I2C_M_NOSTART functionality of i2c
protocol mangling.
Removing the I2C_M_NOSTART functionality support for Tegra20.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra's i2c controller require two clock sources named as
div_clk and fast_clk.
This change make sure that driver pass the correct clock's
name when it acquires clock handle. Also change the
variable name to reflect the correct clock handles.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
From "Uwe Kleine-Knig" <u.kleine-koenig@pengutronix.de>:
this is the 2nd version of this series whose goal is to make struct
of_device_id.data const. Conceptually a driver must not modify the data
contained there so making it const is the right thing.
v1 of this series was sent with Message-id:
1342182734-321-1-git-send-email-y. Changes since then are:
- powerpc fixes
- several new consts that were found by Arnd that are possible after
patch 19.
Arnd suggested to take this series via arm-soc late for 3.6 in one go
because patch 19 depends on the former patches but is a precondition to
the latter and it fixes a few warnings. So getting it in via the
respective maintainer trees would need a much bigger coordination
effort. That means I prefer getting Acks over you taking the patch.
Vinod Koul already took
dmaengine: at_hdmac: add a few const qualifiers
that is in next-20120723 as 7fd63ccdad now. Vinod, I don't follow your
pull requests, but assuming you didn't let it already pull for 3.6 I
suggest you drop it from your queue and I just take your Ack.
This series was build tested for arm (all defconfigs) and powerpc (all
defconfigs and an allyesconfig) and grep didn't find more issues. As
before it introduces a warning in drivers/regulator/twl-regulator.c.
This driver does modify its .of_match_table when a device is bound which
doesn't fits the concept of independant devices. Arnd noticed another
new warning in drivers/scsi/qlogicpti.c that isn't that easy to resolve,
because the pointer to (now) const data is passed as first argument to
scsi_host_alloc. To fix that properly struct Scsi_Host.hostt needs to
get a const, too. Alternatively I could introduce a cast removing the
const, but I don't like that.
* 'ofdeviceiddata' of git://git.pengutronix.de/git/ukl/linux: (25 commits)
dma: tegra: make data used as *of_device_id.data const
can: mpc5xxx_can: make data used as *of_device_id.data const
macintosh/mediabay: make data used as *of_device_id.data const
i2c/mpc: make data used as *of_device_id.data const
mfd/da9052: make i2c_device_id array const
powerpc/fsl_msi: drop unneeded cast to non-const pointer
gpio/gpio-omap: make platformdata used as *of_device_id.data const
of: add const to struct *of_device_id.data
dma: tegra: make tegra_dma.chip_data a pointer to const data
watchdog/mpc8xxx: add a const qualifier
powerpc/celleb_pci: add a const qualifier
powerpc/fsl_msi: add a const qualifier
powerpc/83xx: add a const qualifier
macintosh/mediabay: add a const qualifier
mmc/omap_hsmmc: add a const qualifier
i2c/mpc: add a const qualifier
i2c/i2c-omap: add a const qualifier
gpio/mpc8xxx: add a const qualifier
gpio/gpio-omap.c: add a const qualifier
misc/atmel_tc: make atmel_tc.tcb_config member point to const data
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[olof: repulled a v3 version of the branch that rebased to add some more
acked-bys and added one more patch on top for tegra]
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit cd4f2d4 (i2c: mxs: Set I2C timing registers for mxs-i2c) only
covered the case for devicetree and made platform_data based boards
bail out with -EINVAL. Correctly support the latter one, too.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
On transactions with n>=2 bytes, the controller actually wrongly clocks in n+1
bytes. This is caused by the (wrong) assumption that RFE in the Status Register
is 1 iff there is no byte already ordered (via a dummy TX byte). This lead to
the implementation of synchronized byte ordering, e.g.:
Dummy-TX - RX - Dummy-TX - RX - ...
But since RFE actually stays high after some Dummy-TX, it rather looks like:
Dummy-TX - Dummy-TX - RX - Dummy-TX - RX - (RX)
The last RX byte is clocked in by the bus controller, but ignored by the kernel
when filling the userspace buffer.
This patch fixes the issue by asking for RX via Dummy-TX asynchronously.
Introducing a separate counter for TX bytes.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The I2C Control Register bits RFDAIE and RFFIE were mixed up. In addition to
this fix, this patch adds the missing bit DRSIE for completeness.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
When booting using a device tree, the adapter number is dynamically
assigned after the log message is sent.
This patch modifies the log message to get a correct adapter id.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
move the goto out label one line down, so that
it can be used when stat is read as zero. All
other exits, can be done with a break statement.
While at that, also break out as soon as we
complete draining IRQ, since at that time
we know we transferred everything there was
to be transferred.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
this helps us reduce unnecessary pm transitions
in case we have another i2c message starting soon.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
before starting any messages we call pm_runtime_get_sync()
which will make sure that by the time we program a transfer
and our IRQ handler gets called, we're not suspended
anymore.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
for OMAP2, we can easily switch over to threaded
IRQs on the I2C driver. This will allow us to
spend less time in hardirq context.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[Trivial formating changes]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently omap_i2c_ack_stat doesn't use the stat variable.
After the read of the I2C_STAT_REG it is not used.
Remove the redundant read of the status register.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
we can ack stat and complete the command from
the errata handling itself.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch will try to avoid the usage of
draining feature by reconfiguring the FIFO
the start condition of each message based
on the message's size.
By doing that, we will be better utilizing
the FIFO when doing big transfers.
While at that also drop the now unneeded
check for dev->buf_len as we always know
the amount of data to be transmitted.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
instead of having multiple return points, use
a goto statement to make that clearer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Always return IRQ_HANDLED otherwise we could get our IRQ line disabled due
to many spurious IRQs.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[Trivial changes to commitlogs]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
omap_i2c_dev is allocated with kzalloc(),
so we need not initialize b_hw to zero.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
that way we can ignore TX IRQs while in receiver
mode and ignore RX IRQs while in transmitter mode.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[Remove unnecessary braces]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
that's a nice helper from drivers core which
will give us the exact IRQ number, instead
of a pointer to an IRQ resource.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
According to flow diagrams on OMAP TRMs,
we should ACK the IRQ as they happen.
Signed-off-by: Felipe Balbi <balbi@ti.com>
[Ack the stat OMAP_I2C_STAT_AL in case of arbitration lost]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
this will make sure that we execute at least once.
No functional changes otherwise.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
re-factor the common parts to a separate function,
so that code is easier to read and understand.
No functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make it not depend on ISR's local variables
in order to make it easier to re-factor the
transmit data loop.
Also since we are waiting for XUDF(Transmitter underflow) just before
writing data lets not flag the underflow.
This is anyways going to go once we write
the data.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
While they do pretty much the same thing, there
are a few peculiarities. Specially WRT erratas,
it's best to split those out and re-factor the
read/write loop to another function which both
cases call.
This last part will be done on another patch.
While at that, also avoid an unncessary register
read since dev->fifo_len will always contain the
correct amount of data to be transferred.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
stat & BIT(1) is the same as BIT(1), so let's
simplify things a bit by removing "stat &" from
all omap_i2c_ack_stat() calls.
Code snippet (extremely simplified):
if (stat & NACK) {
...
omap_i2c_ack_stat(dev, stat & NACK);
}
if (stat & RDR) {
...
omap_i2c_ack_stat(dev, stat & RDR);
}
and so on. The tricky place is only WRT errata handling, for example:
if (*stat & (NACK | AL)) {
omap_i2c_ack_stat(dev, *stat & (XRDY | XDR));
...
}
but in this case, the errata says we must clear XRDY and XDR if that
errata triggers, so if they just got enabled or not, it doesn't matter.
Another tricky place is RDR | RRDY (likewise for XDR | XRDY):
if (stat & (RDR | RRDY)) {
...
omap_i2c_ack_stat(dev, stat & (RDR | RRDY));
}
again here there will be no issues because those IRQs never fire
simultaneously and one will only after after we have handled the
previous, that's because the same FIFO is used anyway and we won't shift
data into FIFO until we tell the IP "hey, I'm done with the FIFO, you
can shift more data"
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
[Added the explaination from the discurssion to the commit logs]
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
trivial patch to aid readability. No functional
changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The patch intends to decrease the indentation level on the
data handling
by using the fact that else of if (dev->buf_len) is same as
if (!dev->buf_len)
if (dev->buf_len) {
aaa;
} else {
bbb;
break;
}
to
if (!dev->buf_len) {
bbb;
break;
}
aaa;
Hence no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
trivial patch, no functional changes
If the fifo is disabled or fifo_size is 0 the num_bytes
is set to 1. Else it is set to fifo_size or in case of a
draining interrupt the remaining bytes in the buff stat.
So the zero check is redundant and can be safely optimised.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by : Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
that helps deleting some boiler plate code
and lets driver-core manage our resources
for us.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This driver has the following properties compared to the old driver:
1. Support for multiple interfaces.
2. Interrupt driven I/O as opposed to polling/busy waiting.
3. Support for _one_ repeated start (Sr) condition, which is enough
for most real-world applications including all SMBus transfer types.
(The hardware does not support issuing arbitrary Sr conditions on the
bus.)
testing: SoC: at91sam9g45
- BQ20Z80 battery SMBus client.
- on a 2.6.38 kernel with several i2c clients (temp-sensor,
audio-codec, touchscreen-controller, w1-bridge, io-expanders)
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Tested-by: Hubert Feurstein <h.feurstein@gmail.com>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[wsa: squashed with the following patches from Ludovic to have some flaws
fixed:
i2c: at91: use managed resources
i2c: at91: add warning about transmission issues for some devices
i2c: at91: use an id table for SoC dependent parameters
]
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
It will get replaced by a superior one. Safe to remove since this one
depends on BROKEN anyhow.
Signed-off-by: Nikolaus Voss <n.voss@weinmann.de>
Tested-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[wsa: added commit message]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The regulator fetched by the Nomadik I2C driver is actually a
voltage domain regulator. Stop doing this in the driver and
let the power domain code handle any regulators, as discussed
on the list.
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
add of support for the davinci i2c driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[wsa: fix indentation in the binding description]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Use dev_dbg logging style as it is done in other parts of this driver.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
It is useful information in dmesg to have a message indicating that the i2c
driver was succesfully registered, so promote it to dev_info.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Since of_device_id.data is declared as a pointer to const data a few
more consts can be added in this driver.
[ukl: split Arnd's patch by driver]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:
drivers/i2c/busses/i2c-mpc.c: In function 'fsl_i2c_probe':
drivers/i2c/busses/i2c-mpc.c:650:31: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This prepares *of_device_id.data becoming const. Without this change
the following warning would occur:
drivers/i2c/busses/i2c-omap.c: In function 'omap_i2c_probe':
drivers/i2c/busses/i2c-omap.c:1025: warning: assignment discards qualifiers from pointer target type
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
If kernel is compiled with CONFIG_PROVE_LOCKING the
validator raises an error when a multiplexer is removed
via sysfs and sub-clients are connected to it. This is a
false positive.
Documentation/lockdep-design.txt recommends to handle this
via calls to mutex_lock_nested().
Based on an earlier fix from Michael Lawnick.
Note that the extra code resolves to nothing unless
CONFIG_DEBUG_LOCK_ALLOC=y.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>
This patch adds config I2C_DESIGNWARE_CORE in Kconfig, and let
I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI select I2C_DESIGNWARE_CORE.
Because both I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI can be built as
built-in or module, we also need to export the functions in i2c-designware-core.
This fixes below build error when CONFIG_I2C_DESIGNWARE_PLATFORM=y &&
CONFIG_I2C_DESIGNWARE_PCI=y:
LD drivers/i2c/busses/built-in.o
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_clear_int':
i2c-designware-core.c:(.text+0xa10): multiple definition of `i2c_dw_clear_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x928): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_init':
i2c-designware-core.c:(.text+0x178): multiple definition of `i2c_dw_init'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x90): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_readl':
i2c-designware-core.c:(.text+0xe8): multiple definition of `dw_readl'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_isr':
i2c-designware-core.c:(.text+0x724): multiple definition of `i2c_dw_isr'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x63c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer':
i2c-designware-core.c:(.text+0x4b0): multiple definition of `i2c_dw_xfer'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c8): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_is_enabled':
i2c-designware-core.c:(.text+0x9d4): multiple definition of `i2c_dw_is_enabled'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8ec): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_writel':
i2c-designware-core.c:(.text+0x124): multiple definition of `dw_writel'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer_msg':
i2c-designware-core.c:(.text+0x2e8): multiple definition of `i2c_dw_xfer_msg'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x200): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_enable':
i2c-designware-core.c:(.text+0x9c8): multiple definition of `i2c_dw_enable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8e0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_read_comp_param':
i2c-designware-core.c:(.text+0xa24): multiple definition of `i2c_dw_read_comp_param'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x93c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable':
i2c-designware-core.c:(.text+0x9dc): multiple definition of `i2c_dw_disable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8f4): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_func':
i2c-designware-core.c:(.text+0x710): multiple definition of `i2c_dw_func'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x628): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable_int':
i2c-designware-core.c:(.text+0xa18): multiple definition of `i2c_dw_disable_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x930): first defined here
make[3]: *** [drivers/i2c/busses/built-in.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org [3.2+]
Add the SMBus Device IDs for the Intel Lynx Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Removes the pnx4008 platform support, which hasn't seen any active
development since 2006 and seems to be unused these days.
* 'pnx4008-removal' of git://git.antcom.de/linux-2.6:
ARM: mach-pnx4008: Remove architecture
As Stephen Rothwell reports, a849088aa1 ("ARM: Fix ioremap() of
address zero") from the arm-current tree and commit c279443709 ("ARM:
Add fixed PCI i/o mapping") from the arm-soc tree conflict in
a nontrivial way in arch/arm/mm/mmu.c.
Rob Herring explains:
The PCI i/o reserved area has a dummy physical address of 0 and
needs to be skipped by ioremap searches. So we don't set
VM_ARM_STATIC_MAPPING to prevent matches by ioremap. The vm_struct
settings don't really matter when we do the real mapping of the
i/o space.
Since commit a849088aa1 is at the start of the fixes branch
in the arm tree, we can merge it into the branch that contains
the other ioremap changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes the ARM architecture mach-pnx4008. No direct support or user
feedback since 2006. Acknowledgements from NXP/Philips and Linux arm-soc
maintainers.
Signed-off-by: Roland Stigge <stigge@antcom.de>
The CONFIG_PM doesn't actually enable any of the PM callbacks, it
only allows to enable CONFIG_PM_SLEEP and CONFIG_PM_RUNTIME.
This means if CONFIG_PM is used to protect system sleep callbacks
then it may end up unreferenced if only runtime PM is enabled.
Hence protecting sleep callbacks with CONFIG_PM_SLEEP.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The master_xfer function returns 0 on success. It should return the number of
successful transactions.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
In omap_i2c_xfer(), ensure pm_runtime_put() is called, even on
failure.
Without this, after a failed xfer, the runtime PM usecount will have
been incremented, but not decremented causing the usecount to never
reach zero after a failure. This keeps the device always runtime PM
enabled which keeps the enclosing power domain active, and prevents
full-chip retention/off from happening during idle.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
At this moment in time there is only one known configuration for the
Nomadik I2C driver. By not holding that configuration in the driver
adds some unnecessary overhead in platform code. The configuration
has already been removed from platform code, this patch checks for any
over-riding configurations. If there aren't any, the default is used.
[LinusW says: "Right now this is causing boot regressions so we need it
badly..."]
Acked-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
from interrupts for /dev/random and /dev/urandom. The goal is to
addresses weaknesses discussed in the paper "Mining your Ps and Qs:
Detection of Widespread Weak Keys in Network Devices", by Nadia
Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman, which will
be published in the Proceedings of the 21st Usenix Security Symposium,
August 2012. (See https://factorable.net for more information and an
extended version of the paper.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABCAAGBQJQF/0DAAoJENNvdpvBGATwIowQAOep9QKtLrBvb2lwIRVmeiy8
lRf7V/tYZnz4FePbR0W92JQfKYkCV8yyOO0bmeRzWL3v4m+lRwDTSyA1DDyQMoH+
LOMzvDKSLJMSXTXdSOIr1WYACphViCR/9CrbMBCKSkYfZLJ1MdaEDxT3rcpTGD0T
6iknUweiSkHHhkerU5yQL7FKzD5kYUe0hsF47w7QVlHRHJsW2fsZqkFoh+RpnhNw
03u+djxNGBo9qV81vZ9D1b0vA9uRlEjoWOOEG2XE4M2iq6TUySueA72dQnCwunfi
3kG/u1Swv2dgq6aRrP3H7zdwhYSourGxziu3jNhEKwKEohrxYY7xjNX3RVeTqP67
AzlKsOTWpRLIDrzjSLlb8VxRQiZewu8Unex3e1G+eo20sbcIObHGrxNp7K00zZvd
QZiMHhOwItwFTe4lBO+XbqH2JKbL9/uJmwh5EipMpQTraKO9E6N3CJiUHjzBLo2K
iGDZxRMKf4gVJRwDxbbP6D70JPVu8ZJ09XVIpsXQ3Z1xNqaMF0QdCmP3ty56q1o0
NvkSXxPKrijZs8Sk0rVDqnJ3ll8PuDnXMv5eDtL42VT818I5WxESn9djjwEanGv0
TYxbFub/NRxmPEE5B2Js5FBpqsLf5f282OSMeS/5WLBbnHJR1OoPoAhGVpHvxntC
bi5FC1OolqhvzVIdsqgt
=u7KM
-----END PGP SIGNATURE-----
Merge tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random subsystem patches from Ted Ts'o:
"This patch series contains a major revamp of how we collect entropy
from interrupts for /dev/random and /dev/urandom.
The goal is to addresses weaknesses discussed in the paper "Mining
your Ps and Qs: Detection of Widespread Weak Keys in Network Devices",
by Nadia Heninger, Zakir Durumeric, Eric Wustrow, J. Alex Halderman,
which will be published in the Proceedings of the 21st Usenix Security
Symposium, August 2012. (See https://factorable.net for more
information and an extended version of the paper.)"
Fix up trivial conflicts due to nearby changes in
drivers/{mfd/ab3100-core.c, usb/gadget/omap_udc.c}
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (33 commits)
random: mix in architectural randomness in extract_buf()
dmi: Feed DMI table to /dev/random driver
random: Add comment to random_initialize()
random: final removal of IRQF_SAMPLE_RANDOM
um: remove IRQF_SAMPLE_RANDOM which is now a no-op
sparc/ldc: remove IRQF_SAMPLE_RANDOM which is now a no-op
[ARM] pxa: remove IRQF_SAMPLE_RANDOM which is now a no-op
board-palmz71: remove IRQF_SAMPLE_RANDOM which is now a no-op
isp1301_omap: remove IRQF_SAMPLE_RANDOM which is now a no-op
pxa25x_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
omap_udc: remove IRQF_SAMPLE_RANDOM which is now a no-op
goku_udc: remove IRQF_SAMPLE_RANDOM which was commented out
uartlite: remove IRQF_SAMPLE_RANDOM which is now a no-op
drivers: hv: remove IRQF_SAMPLE_RANDOM which is now a no-op
xen-blkfront: remove IRQF_SAMPLE_RANDOM which is now a no-op
n2_crypto: remove IRQF_SAMPLE_RANDOM which is now a no-op
pda_power: remove IRQF_SAMPLE_RANDOM which is now a no-op
i2c-pmcmsp: remove IRQF_SAMPLE_RANDOM which is now a no-op
input/serio/hp_sdc.c: remove IRQF_SAMPLE_RANDOM which is now a no-op
mfd: remove IRQF_SAMPLE_RANDOM which is now a no-op
...
Pull media updates from Mauro Carvalho Chehab:
"This is the first part of the media patches for v3.6.
This patch series contain:
- new DVB frontend: rtl2832
- new video drivers: adv7393
- some unused files got removed
- a selection API cleanup between V4L2 and V4L2 subdev API's
- a major redesign at v4l-ioctl2, in order to clean it up
- several driver fixes and improvements."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (174 commits)
v4l: Export v4l2-common.h in include/linux/Kbuild
media: Revert "[media] Terratec Cinergy S2 USB HD Rev.2"
[media] media: Use pr_info not homegrown pr_reg macro
[media] Terratec Cinergy S2 USB HD Rev.2
[media] v4l: Correct conflicting V4L2 subdev selection API documentation
[media] Feature removal: V4L2 selections API target and flag definitions
[media] v4l: Unify selection flags documentation
[media] v4l: Unify selection flags
[media] v4l: Common documentation for selection targets
[media] v4l: Unify selection targets across V4L2 and V4L2 subdev interfaces
[media] v4l: Remove "_ACTUAL" from subdev selection API target definition names
[media] V4L: Remove "_ACTIVE" from the selection target name definitions
[media] media: dvb-usb: print mac address via native %pM
[media] s5p-tv: Use module_i2c_driver in sii9234_drv.c file
[media] media: gpio-ir-recv: add allowed_protos for platform data
[media] s5p-jpeg: Use module_platform_driver in jpeg-core.c file
[media] saa7134: fix spelling of detach in label
[media] cx88-blackbird: replace ioctl by unlocked_ioctl
[media] cx88: don't use current_norm
[media] cx88: fix a number of v4l2-compliance violations
...
Merge Andrew's first set of patches:
"Non-MM patches:
- lots of misc bits
- tree-wide have_clk() cleanups
- quite a lot of printk tweaks. I draw your attention to "printk:
convert the format for KERN_<LEVEL> to a 2 byte pattern" which
looks a bit scary. But afaict it's solid.
- backlight updates
- lib/ feature work (notably the addition and use of memweight())
- checkpatch updates
- rtc updates
- nilfs updates
- fatfs updates (partial, still waiting for acks)
- kdump, proc, fork, IPC, sysctl, taskstats, pps, etc
- new fault-injection feature work"
* Merge emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
drivers/misc/lkdtm.c: fix missing allocation failure check
lib/scatterlist: do not re-write gfp_flags in __sg_alloc_table()
fault-injection: add tool to run command with failslab or fail_page_alloc
fault-injection: add selftests for cpu and memory hotplug
powerpc: pSeries reconfig notifier error injection module
memory: memory notifier error injection module
PM: PM notifier error injection module
cpu: rewrite cpu-notifier-error-inject module
fault-injection: notifier error injection
c/r: fcntl: add F_GETOWNER_UIDS option
resource: make sure requested range is included in the root range
include/linux/aio.h: cpp->C conversions
fs: cachefiles: add support for large files in filesystem caching
pps: return PTR_ERR on error in device_create
taskstats: check nla_reserve() return
sysctl: suppress kmemleak messages
ipc: use Kconfig options for __ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION
ipc: compat: use signed size_t types for msgsnd and msgrcv
ipc: allow compat IPC version field parsing if !ARCH_WANT_OLD_COMPAT_IPC
ipc: add COMPAT_SHMLBA support
...
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in
clk.h, there is no need to have clk code enclosed in #ifdef
CONFIG_HAVE_CLK, #endif macros.
pxa i2c also has these dummy macros defined locally. Remove them as they
aren't required anymore.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS updates from Ralf Baechle:
"More hardware support across the field including a bunch of device
drivers. The highlight however really are further steps towards
device tree.
This has been sitting in -next for ages. All MIPS _defconfigs have
been tested to boot or where I don't have hardware available, to at
least build fine."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (77 commits)
MIPS: Loongson 1B: Add defconfig
MIPS: Loongson 1B: Add board support
MIPS: Netlogic: early console fix
MIPS: Netlogic: Fix indentation of smpboot.S
MIPS: Netlogic: remove cpu_has_dc_aliases define for XLP
MIPS: Netlogic: Remove unused pcibios_fixups
MIPS: Netlogic: Add XLP SoC devices in FDT
MIPS: Netlogic: Add IRQ mappings for more devices
MIPS: Netlogic: USB support for XLP
MIPS: Netlogic: XLP PCIe controller support.
MIPS: Netlogic: Platform changes for XLR/XLS I2C
MIPS: Netlogic: Platform NAND/NOR flash support
MIPS: Netlogic: Platform changes for XLS USB
MIPS: Netlogic: Remove NETLOGIC_ prefix
MIPS: Netlogic: SMP wakeup code update
MIPS: Netlogic: Update comments in smpboot.S
MIPS: BCM63XX: Add 96328avng reference board
MIPS: Expose PCIe drivers for MIPS
MIPS: BCM63XX: Add PCIe Support for BCM6328
MIPS: BCM63XX: Move the PCI initialization into its own function
...
Pull embedded i2c changes from Wolfram Sang:
"Changes for the "embedded" part of the I2C subsystem:
- lots of devicetree conversions of drivers (and preparations for
that)
- big cleanups for drivers for OMAP, Tegra, Nomadik, Blackfin
- Rafael's struct dev_pm_ops conversion patches for I2C
- usual driver cleanups and fixes
All patches have been in linux-next for an apropriate time and all
patches touching files outside of i2c-folders should have proper acks
from the maintainers."
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (60 commits)
Revert "i2c: tegra: convert normal suspend/resume to *_noirq"
I2C: MV64XYZ: Add Device Tree support
i2c: stu300: use devm managed resources
i2c: i2c-ocores: support for 16bit and 32bit IO
V4L/DVB: mfd: use reg_shift instead of regstep
i2c: i2c-ocores: Use reg-shift property
i2c: i2c-ocores: DT bindings and minor fixes.
i2c: mv64xxxx: remove EXPERIMENTAL tag
i2c-s3c2410: Use plain pm_runtime_put()
i2c: s3c2410: Fix pointer type passed to of_match_node()
i2c: mxs: Set I2C timing registers for mxs-i2c
i2c: i2c-bfin-twi: Move blackfin TWI register access Macro to head file.
i2c: i2c-bfin-twi: Move TWI peripheral pin request array to platform data.
i2c:i2c-bfin-twi: include twi head file
i2c:i2c-bfin-twi: TWI fails to restart next transfer in high system load.
i2c: i2c-bfin-twi: Tighten condition when failing I2C transfer if MEN bit is reset unexpectedly.
i2c: i2c-bfin-twi: Break dead waiting loop if i2c device misbehaves.
i2c: i2c-bfin-twi: Improve the patch for bug "Illegal i2c bus lock upon certain transfer scenarios".
i2c: i2c-bfin-twi: Illegal i2c bus lock upon certain transfer scenarios.
i2c-mv64xxxx: allow more than one driver instance
...
Conflicts:
drivers/i2c/busses/i2c-nomadik.c
Instead of using the custom iop3xx gpio functions, use the gpiolib
variants. This should be functionally the same since the gpiolib
just calls the iop3xx gpio functions. This is needed in preparation
of removing iop3xx mach/io.h headers.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: "Jean Delvare (PC drivers, core)" <khali@linux-fr.org>
Cc: "Ben Dooks (embedded platforms)" <ben-linux@fluff.org>
Cc: "Wolfram Sang (embedded platforms)" <w.sang@pengutronix.de>
Cc: linux-i2c@vger.kernel.org
This reverts commit 7c86d44cda.
Stephen says:
IIRC, I proposed it before solely to solve some suspend/resume ordering
issues, and Colin Cross NAKd it. These days, deferred probe should make
this change unnecessary.
Reported-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Generate a stop condition after each message marked with I2C_M_STOP.
[JD: Add I2C_FUNC_PROTOCOL_MANGLING.]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Adapter drivers might support only a subset of the SMBus operations
natively. Those drivers currently have to manually emulate unsupported
operations using I2C.
Make the i2c_smbus_xfer() function fall back to
i2c_smbus_xfer_emulated() when the adapter's .smbus_xfer() operation
returns -EOPNOTSUPP, like it already does when the .smbus_xfer()
operation isn't available at all.
[JD: Minor optimization.]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
SCCB is a serial communication bus developed by Omnivision. Its 2-wire
mode is very similar to SMBus byte data transactions, but requires the
controller to ignore the ACK bit and to insert a stop condition after
each message.
Add a device SCCB flag and a message stop flag to be passed to
controller drivers.
[JD: Kill rogue definition in go7007 driver.]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Robofuzz OSIF is a generic USB/iIC interface that embeds an ATMega8A
AVR-RISC microcontroler.
The device is based upon Till Harbaum's i2c-tiny-usb and although it
enhances the original design with further functionnalities it still
maintain compatibility with it with respect to the USB/I2C interface.
Signed-off-by: Emmanuel Deloget <logout@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Byte-by-byte transactions are used primarily for accessing I2C devices
with an SMBus controller. For these transactions, for each byte that is
read or written, the SMBus controller generates a BYTE_DONE IRQ. The isr
reads/writes the next byte, and clears the IRQ flag to start the next byte.
On the penultimate IRQ, the isr also sets the LAST_BYTE flag.
There is no locking around the cmd/len/count/data variables, since the
I2C adapter lock ensures there is never multiple simultaneous transactions
for the same device, and the driver thread never accesses these variables
while interrupts might be occurring.
The end result is faster I2C block read and write transactions.
Note: This patch has only been tested and verified by doing I2C read and
write block transfers on Cougar Point 6 Series PCH, as well as I2C read
block transfers on ICH5.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Enable interrupts on more devices. ICH5, ICH7(-M) and ICH10 have been
tested to work OK. ICH8 and ICH9 are expected to work just fine as
they are very close to ICH7 and ICH10.
Ultimately we want to enable this feature on at least every device
since the ICH5, but for now we limit the exposure. We'll enable it for
other devices if we don't get negative feedback.
As a bonus, let the user know when interrupts are used.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Add a new 'feature' to i2c-i801 to enable using PCI interrupts.
When the feature is enabled, then an isr is installed for the device's
PCI IRQ.
An I2C/SMBus transaction is always terminated by one of the following
interrupt sources: FAILED, BUS_ERR, DEV_ERR, or on success: INTR.
When the isr fires for one of these cases, it sets the ->status variable
and wakes up the waitq. The waitq then saves off the status code, and
clears ->status (in preparation for some future transaction).
The SMBus controller generates an INTR irq at the end of each
transaction where INTREN was set in the HST_CNT register.
No locking is needed around accesses to priv->status since all writes to
it are serialized: it is only ever set once in the isr at the end of a
transaction, and cleared while no interrupts can occur. In addition, the
I2C adapter lock guarantees that entire I2C transactions for a single
adapter are always serialized.
For this patch, the INTREN bit is set only for SMBus block, byte and word
transactions, but not for I2C reads or writes. The use of the DS
(BYTE_DONE) interrupt with byte-by-byte I2C transactions is implemented in
a subsequent patch.
The interrupt feature has only been enabled for COUGARPOINT hardware.
In addition, it is disabled if SMBus is using the SMI# interrupt.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
(Based on earlier work by Daniel Kurtz.)
Come up with a consistent, driver-wide strategy for event polling. For
intermediate steps of byte-by-byte block transactions, check for
BYTE_DONE or any error flag being set. At the end of every transaction
(regardless of PEC being used), check for both BUSY being cleared and
INTR or any error flag being set. This ensures proper action for all
transaction types.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Daniel Kurtz <djkurtz@chromium.org>
Later patches enable interrupts. This preliminary patch removes the older
unsupported ENABLE_INT9 flag.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Rename the SMBHSTCNT register bit access constants to match the style of
other register bits.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If an error is detected in the polling loop, abort the transaction and
return an error code.
* DEV_ERR is set if the device does not respond with an acknowledge, and
the SMBus controller times out (minimum 25ms).
* BUS_ERR is set if a bus arbitration collision is detected. In other
words, when the SMBus controller tries to generate a START condition, but
detects that the SMBDATA is being held low, usually by another SMBus/I2C
master.
* FAILED is only set if a transaction is stopped by software (using
the SMBHSTCNT KILL bit).
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Writing back the whole status register could clear unwanted bits.
In particular, it could clear the "INUSE_STS" bit, which is a
'hardware semaphore', that might be useful to use some day.
To prepare for this, let's ban writing back the whole status to register
HST_STS, of which this is the only instance.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As a slight optimization, pull some logic out of the polling loop during
byte-by-byte transactions by just setting the I801_LAST_BYTE bit, as
defined in the i801 (PCH) datasheet, when reading the last byte of a
byte-by-byte I2C_SMBUS_READ.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Using module_i2c_driver() makes the code smaller and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some AMD chipsets, such as the SP5100, have an auxiliary SMBus
controller with a second set of registers. This patch adds
support for this auxiliary controller.
Tested on ASUS KCMA-D8 motherboard.
Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some chipsets have multiple sets of SMBus registers each controlling a
separate SMBus. Supporting these chipsets properly will require registering
multiple I2C adapters for one piix4.
The code to initialize and register the i2c_adapter structure has been
separated from piix4_probe and allows registration of a piix4 adapter
given its base address. Note that the i2c_adapter and i2c_piix4_adapdata
structures are now dynamically allocated.
Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Some chipsets have multiple sets of piix4-compatible SMBus registers.
Eliminating the global variable will allow these chipsets to be fully
supported.
Return value from piix4_setup and piix4_sb800_setup now returns the smba
value detected. This is stored in a struct i2c_piix4_adapdata. Thus
the global variable is eliminated.
Signed-off-by: Andrew Armenia <andrew@asquaredlabs.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Convert the drivers in drivers/i2c/busses/* to usemodule_pci_driver()
macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Olof Johansson <olof@lixom.net>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Tomoya MORINAGA <tomoya.rohm@gmail.com>
My old e-mail address won't be valid for much longer. Time to update it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Pull powerpc updates from Benjamin Herrenschmidt:
"Notable highlights:
- iommu improvements from Anton removing the per-iommu global lock in
favor of dividing the DMA space into pools, each with its own lock,
and hashed on the CPU number. Along with making the locking more
fine grained, this gives significant improvements in multiqueue
networking scalability.
- Still from Anton, we know provide a vdso based variant of getcpu
which makes sched_getcpu with the appropriate glibc patch something
like 18 times faster.
- More anton goodness (he's been busy !) in other areas such as a
faster __clear_user and copy_page on P7, various perf fixes to
improve sampling quality, etc...
- One more step toward removing legacy i2c interfaces by using new
device-tree based probing of platform devices for the AOA audio
drivers
- A nice series of patches from Michael Neuling that helps avoiding
confusion between register numbers and litterals in assembly code,
trying to enforce the use of "%rN" register names in gas rather
than plain numbers.
- A pile of FSL updates
- The usual bunch of small fixes, cleanups etc...
You may spot a change to drivers/char/mem. The patch got no comment
or ack from outside, it's a trivial patch to allow the architecture to
skip creating /dev/port, which we use to disable it on ppc64 that
don't have a legacy brige. On those, IO ports 0...64K are not mapped
in kernel space at all, so accesses to /dev/port cause oopses (and
yes, distros -still- ship userspace that bangs hard coded ports such
as kbdrate)."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/mpic: Create a revmap with enough entries for IPIs and timers
Remove stale .rej file
powerpc/iommu: Fix iommu pool initialization
powerpc/eeh: Check handle_eeh_events() return value
powerpc/85xx: Add phy nodes in SGMII mode for MPC8536/44/72DS & P2020DS
powerpc/e500: add paravirt QEMU platform
powerpc/mpc85xx_ds: convert to unified PCI init
powerpc/fsl-pci: get PCI init out of board files
powerpc/85xx: Update corenet64_smp_defconfig
powerpc/85xx: Update corenet32_smp_defconfig
powerpc/85xx: Rename P1021RDB-PC device trees to be consistent
powerpc/watchdog: move booke watchdog param related code to setup-common.c
sound/aoa: Adapt to new i2c probing scheme
i2c/powermac: Improve detection of devices from device-tree
powerpc: Disable /dev/port interface on systems without an ISA bridge
of: Improve prom_update_property() function
powerpc: Add "memory" attribute for mfmsr()
powerpc/ftrace: Fix assembly trampoline register usage
powerpc/hw_breakpoints: Fix incorrect pointer access
powerpc: Put the gpr save/restore functions in their own section
...
Clock support is moving to the clk subsystem. These tegra, omap and imx
changes are for code that is still platform specific and not (yet)
part of that subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Cvpa
-----END PGP SIGNATURE-----
Merge tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clk changes from Arnd Bergmann:
"Clock support is moving to the clk subsystem. These tegra, omap and
imx changes are for code that is still platform specific and not (yet)
part of that subsystem."
Fix up conflicts in arch/arm/mach-{imx/clk-imx51-imx53.c,omap2/Makefile}
* tag 'clk' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
ARM: imx: clk-imx31: Fix clock id for rnga driver
ARM: imx: add missing item to the list of clock event modes
ARM: i.MX5x CSPI: Fixed clock name for CSPI
ARM: i.MX5x clocks: Fix GPT clocks
ARM: i.MX5x clocks: Fix parent for PWM clocks
ARM: i.MX5x clocks: Add EPIT support
ARM: mx27: Reenable silicon version print
ARM: clk-imx27: Fix rtc clock id
ARM: tegra: Provide clock for only one PWM controller
ARM: tegra: Fix PWM clock programming
ARM: OMAP3+: clock33xx: Add AM33XX clock tree data
ARM: OMAP3+: clock: Move common clksel_rate & clock data to common file
ARM: tegra: dma: rename driver name for clock to "tegra-apbdma"
ARM: tegra: Remove second instance of uart clk
crypto: add clk_prepare/clk_unprepare
ASoC: tegra: add clk_prepare/clk_unprepare
staging: nvec: add clk_prepare/clk_unprepare
spi/tegra: add clk_prepare/clk_unprepare
Input: tegra-kbc - add clk_prepare/clk_unprepare
USB: ehci-tegra: add clk_prepare/clk_unprepare
...
The I.MX platform is getting converted to use sparse IRQs. We are doing
this for all platforms over time, because this is one of the
requirements for building a multiplatform kernel, and generally a good
idea.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Y2Sm
-----END PGP SIGNATURE-----
Merge tag 'irq' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc sparse IRQ conversion from Arnd Bergmann:
"The I.MX platform is getting converted to use sparse IRQs. We are
doing this for all platforms over time, because this is one of the
requirements for building a multiplatform kernel, and generally a good
idea."
* tag 'irq' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: imx: select USE_OF
ARM: imx: Fix build error due to missing irqs.h include
ARM: imx: enable SPARSE_IRQ for imx platform
ARM: fiq: change FIQ_START to a variable
tty: serial: imx: remove the use of MXC_INTERNAL_IRQS
ARM: imx: remove unneeded mach/irq.h inclusion
i2c: imx: remove unneeded mach/irqs.h inclusion
ARM: imx: add a legacy irqdomain for mx31ads
ARM: imx: add a legacy irqdomain for 3ds_debugboard
ARM: imx: pass gpio than irq number into mxc_expio_init
ARM: imx: leave irq_base of wm8350_platform_data uninitialized
dma: ipu: remove the use of ipu_platform_data
ARM: imx: move irq_domain_add_legacy call into avic driver
ARM: imx: move irq_domain_add_legacy call into tzic driver
gpio/mxc: move irq_domain_add_legacy call into gpio driver
ARM: imx: eliminate macro IRQ_GPIOx()
ARM: imx: eliminate macro IOMUX_TO_IRQ()
ARM: imx: eliminate macro IMX_GPIO_TO_IRQ()
Extends the driver to get properties from device tree. Rather than
pass the N & M factors in DT, use the more standard clock-frequency
property. Calculate N & M at run time. In order to do this, we need to
know tclk. So the driver uses clk_get() etc in order to get the clock
and clk_get_rate() to determine the tclk rate. Not all platforms
however have CLK, so some #ifdefery is needed to ensure the driver
still compiles when CLK is not available.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[wsa: converted some ints to u32 to match signedness]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
There are three parts to this:
1) Remove the definitions of OCTEON_IRQ_TWSI and OCTEON_IRQ_TWSI2.
The interrupts are specified by the device tree and these hard
coded irq numbers block the used of the irq lines by the irq_domain
code.
2) Remove platform device setup code from octeon-platform.c, it is
now unused.
3) Convert i2c-octeon.c to use device tree. Part of this includes
using the devm_* functions instead of the raw counterparts, thus
simplifying error handling. No functionality is changed.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/3939/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the changes in the random tree, IRQF_SAMPLE_RANDOM is now a
no-op; interrupt randomness is now collected unconditionally in a very
low-overhead fashion; see commit 775f4b297b. The IRQF_SAMPLE_RANDOM
flag was scheduled to be removed in 2009 on the
feature-removal-schedule, so this patch is preparation for the final
removal of this flag.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: "Ben Dooks" <ben-linux@fluff.org>
Cc: "Wolfram Sang" <w.sang@pengutronix.de>
Allocate memory for device state using devm_kzalloc(), get the
clock using devm_clk_get(), get the IRQ using devm_request_irq(),
request and remap memory using devm_request_and_ioremap().
All to simplify accounting and letting the kernel do the
garbage-collection.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Some architectures supports only 16-bit or 32-bit read/write access to
their IO space. Add a 'reg-io-width' platform and OF parameter which
specifies the IO width to support these platforms.
reg-io-width can be specified as 1, 2 or 4, and has a default value
of 1 if it is unspecified.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Deprecate 'regstep' property and use the standard 'reg-shift' property
for register offset shifts. 'regstep' will still be supported as an
optional property, but will give a warning when used.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cleanups to i2c-cores, no change in logic, changes are:
* Move i2c-ocores device tree documentation from source file to
Documentation/devicetree/bindings/i2c/i2c-ocores.txt.
* Add \n to dev_warn and dev_err messages where missing
* Minor updates to the text and formatting fixes.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
As git history indicates, the driver predates the git era and is heavily
used and worked on since. Not EXPERIMENTAL anymore.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Rodolfo Giometti <giometti@linux.it>
Cc: Florian Fainelli <ffainelli@freebox.fr>
There's no point in using _sync() as we don't really care if the suspend
has completed immediately.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This commit fixes warning introduced in 27452498a ("i2c-s3c2410: Rework
device type handling"):
drivers/i2c/busses/i2c-s3c2410.c: In function 's3c24xx_get_device_quirks':
drivers/i2c/busses/i2c-s3c2410.c:125: warning: passing argument 1 of 'of_match_node' from incompatible pointer type
include/linux/of.h:245: note: expected 'const struct of_device_id *' but argument is of type 'const struct of_device_id (*)[4]'
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch configures the I2C bus timing registers according
to information passed via DT. Currently, 100kHz and 400kHz
modes are supported.
The TIMING2 register value is wrong in the documentation for
i.MX28! This was found and fixed by:
Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Now that u5500 is obsolete, u8500 is the only user of the Nomadik
i2c driver. As such there is no requirement to differentiate between
initialisation values. By the time a new SoC is released, almost all
of the ux500 platform will be DT:ed, so we can make decisions based
on the compatible property instead.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
TWI bit mask macros are moved to twi head file.
Depend on commit 61c16b5c74
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Current driver was developed based on BF537 0.2 HRM. In high system load, BUFRDERR error
interrupt may be raised if XMTSERV interrupt of last TX byte is not served in time
(set RSTART bit), which breaks restart tranfer as expected.
"Buffer Read Error (BUFRDERR)" description in Blackfin HRM only applys to BF537
rev. < 0.3. In later rev. and later announced Blackfin chips, such as BF527 and
BF548, a new TWI master feature "Clock Stretching" is added into the TWI controller,
BUFRDERR interrupt is not triggered after TX FIFO is empty.
This patch sets RSTART bit at the beginning of the first transfer. The SCL and SDA
is hold till XMTSERV interrupt of last TX byte is served. Restart transfer is not broken
in high system load.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
[wsa: fixed spaces around operators]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
In order to mark I2C transfer fail when MEN bit in I2C controller is
reset unexpectedly in MCOMP interrupt, interrupt status bits XMTSERV or
RCVSERV should be checked.
Master Transfer Complete (MCOMP).
[1] The initiated master transfer has completed. In the absence of a
repeat start, the bus has been released.
[0] The completion of a transfer has not been detected.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
[wsa: fixed spaces around operators and typo in commit message]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Some fault i2c device may hold the sda/scl line and cause i2c driver
wait in the BUS busy loop. The I2C framework already retry the
transfer loop before timeout. Return -EAGAIN instead of pull BUSBUSY
in the other loop.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
For transfer counts > 255 bytes i2c-bfin-twi sets the data
transfer counter DCNT to 0xFF indicating unlimited transfers.
It then uses a flag iface->manual_stop to manually issue the STOP
condition, once the required amount of bytes are received.
We found that on I2C receive operation issuing the STOP condition
together with a FULL RCV FIFO (2bytes) will cause SDA and SCL be
constantly driven low.
This patch stops receiving operation immediately in last rx interrupt.
This patch also wakes up waiting process when transfer completes.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
For transfer counts > 255 bytes i2c-bfin-twi sets the data
transfer counter DCNT to 0xFF indicating unlimited transfers.
It then uses a flag iface->manual_stop to manually issue the STOP
condition, once the required amount of bytes are received.
We found that on I2C receive operation issuing the STOP condition
together with a FULL RCV FIFO (2bytes) will cause SDA and SCL be
constantly driven low.
Temporary workaround until further investigation:
Discard the RCV FIFO before issuing the STOP condition.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The driver currently checks the platform device id and rejects platform
device id different from 0. This prevents the registration of a second
i2c controller on systems where a second one might be available (such as
Kirkwood 88F6282).
CC: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The OMAP3530 is based upon the same silicon as the OMAP3430 and so the I2C
revision is the same for 3430 and 3530. However, the OMAP3630 device has the
same I2C revision as OMAP4. Correct the revision definition to reflect this.
This patch is based on work done by Jon Hunter <jon-hunter@ti.com>
Changes from his patch
- Update OMAP_I2C_REV_ON_3430 also to reflect that it is same as 3530
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Use INIT_COMPLETION instead of init_completion in transfer.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Use SET_RUNTIME_PM_OPS macro to set runtime functions.
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The omap_i2c_remove function may not be needed after
device exit so the memory could be freed.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
To provide the late suspend and early resume for i2c
driver, convert the suspend/resume as
suspend-> suspend_noirq
resume -> resume_noirq
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[wsa: fixed up to match previous pm_ops change]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make the Tegra I2C controller driver define its PM callbacks through
a struct dev_pm_ops object rather than by using legacy PM hooks
in struct platform_driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
[wsa] adapt to of_match_ptr change
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make the ST-Ericsson U300 I2C controller driver define its PM
callbacks through a struct dev_pm_ops object rather than by using
legacy PM hooks in struct platform_driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make the PKUnity-v3 SoC I2C controller driver define its suspend
callback through a struct dev_pm_ops object rather than by using
a legacy PM hook in struct platform_driver. The empty resume
callback is not necessary, so remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make the PNX I2C controller driver define its PM callbacks through
a struct dev_pm_ops object rather than by using legacy PM hooks
in struct platform_driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make the OpenCores I2C controller driver define its PM callbacks
through a struct dev_pm_ops object rather than by using legacy PM
hooks in struct platform_driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make the Blackfin On-Chip Two Wire Interface driver define its PM
callbacks through a struct dev_pm_ops object rather than by using
legacy PM hooks in struct platform_driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make the AT91 Two-Wire Interface driver define its PM callbacks
through a struct dev_pm_ops object rather than by using legacy PM
hooks in struct platform_driver.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
In place of defining match_table for non-DT based as NULL,
use of_match_ptr() for initialzing the of_match_table.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Use clk_disable_unprepare() inplace of clk_disable().
This was missed as part of moving clock enable/disable to
prepare/unprepare for using the common clock framework.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Remove unused member variable "iomem" of the
i2c device structure.
This variable becomes unused when converted all allocation
to devm_* in following change:
i2c: tegra: make all resource allocation through devm_*
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch adds a number of workarounds for broken Apple device-trees
mostly around sound chips. It handles creating the missing audio codec
devices and works around various issues with missing addresses or
missing compatible properties.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
sparse found this assignment of u32 to an int. Fix it:
drivers/i2c/busses/i2c-imx.c:540:56: warning: incorrect type in argument 3 (different signedness)
and also fix the type in platform_data. All current users use values
which fit into the old and new type, so it is a safe change.
Signed-off-by: Wolfram Sang <wolfram@the-dreams.de>
Reviewed-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
With the new i.mx clock framework the i2c clock is registered as:
clk_register_clkdev(clk[i2c1_ipg_gate], NULL, "imx-i2c.0")
So we do not need to pass "i2c_clk" string and can use NULL instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
[wsa: rebased on top of the devm-conversion]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Make sure we prepare/unprepare the clock for the ST U300
I2C driver as is required by the clk API especially if you
use common clock.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch mutes the false positive compiler warning:
drivers/i2c/busses/i2c-mxs.c: In function 'mxs_i2c_xfer_msg':
drivers/i2c/busses/i2c-mxs.c:206:8: warning: 'data' may be used uninitialized in this function [-Wuninitialized]
drivers/i2c/busses/i2c-mxs.c:196:6: note: 'data' was declared here
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The gateware device has been used outside of the Nomadik world, using
the pci-amba bridge driver, so loosen the dependencies.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The i2c-nomadik gateware is really a PrimeCell APB device. By hosting
the driver under the amba bus we can access it more easily, for
example using the generic pci-amba driver. The patch also fixes the
mach-ux500 users, so they register an amba device instead than a
platform device.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The header and driver are only used by arm/mach-u8500 (and potentially
arm/mach-nomadik), but the STA2X11 I/O Hub exports on PCIe a number of
devices, including i2c-nomadik. This patch allows compilation of the
driver under x86.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
- convert to use devm_request_and_ioremap, devm_kzalloc, devm_clk_get,
devm_request_irq.
- clean up unused variables.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Reviewed-by: Shubhrajyoti D <Shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Use the devm_* for the memory region allocation, interrupt request,
clock handler request.
By doing this, it does not require to explicitly free it and hence
saving some code.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Adding support for functionality I2C_M_NOSTART.
When multiple message transfer request made through i2c
and if any message is flagged with I2C_M_NOSTART then
it will not send the start/repeat-start and address of
that message i.e. sends data directly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The Tegra i2c driver supports the I2C_M_IGNORE_NAK and hence
returning I2C_FUNC_PROTOCOL_MANGLING as supported functionality.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The Tegra PPSB (an peripheral bus) queues writes transactions.
In order to guarantee that writes have completed before a
certain time, a read transaction to a register on the same
bus must be executed.
This is necessary in situations such as when clearing an
interrupt status or enable, so that when returning from an
interrupt handler, the HW has already de-asserted its
interrupt status output, which will avoid spurious interrupts.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
On a board with OMAP3 processor and TWL4030 Power management,
we need to talk to the TWL4030 during late suspend but cannot
because the I2C interrupt is disabled (as late suspend disables
interrupt).
e.g. I get messages like:
[ 62.161102] musb-omap2430 musb-omap2430: LATE power domain suspend
[ 63.167205] omap_i2c omap_i2c.1: controller timed out
[ 63.183044] twl: i2c_read failed to transfer all messages
[ 64.182861] omap_i2c omap_i2c.1: controller timed out
[ 64.198455] twl: i2c_write failed to transfer all messages
[ 65.198455] omap_i2c omap_i2c.1: controller timed out
[ 65.203765] twl: i2c_write failed to transfer all messages
The stack shows omap2430_runtime_suspend calling twl4030_set_suspend
which tries to power-down the USB PHY (twl4030_phy_suspend ->
twl4030_phy_power -> __twl4030_phy_power which as a nice WARN_ON
that helps).
Then we get the same in resume:
[ 69.603912] musb-omap2430 musb-omap2430: EARLY power domain resume
[ 70.610473] omap_i2c omap_i2c.1: controller timed out
[ 70.626129] twl: i2c_write failed to transfer all messages
etc.
So don't disable interrupts for I2C.
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The section number in the recent errata document has changed.
Rename the erratum 1p153 to the unique id i462 instead, so that
it is easier to reference. Also change the function name and comments
to reflect the same.
Cc: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently in the 1.153 errata handling, while waiting for transmitter
underflow, if NACK is got the XUDF(Transmit underflow) flag is also set.
Fix this by setting the XUDF(Transmit underflow) flag after wait for the
condition is over.
Cc: Alexander Shishkin <virtuoso@slind.org>
Acked-by: Moiz Sonasath <m-sonasath@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
i2c_probe set the dev->errata flag, but omap_i2c_init cleared the flag again.
Prevent the overwrite of the errata flags.Move the errata handling to a unified
place in probe to prevent such errors.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Tasslehoff Kjappfot <tasskjapp@gmail.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
If PM runtime get_sync fails return with the error
so that no further reads/writes goes through the interface.
This will avoid possible abort. Add a error message in case
of failure with the cause of the failure.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
By definition, wait_for_completion_timeout() returns an unsigned value and
therefore, it is not necessary to check if the return value is less than zero
as this is not possible.
This is based on a patch from Jon Hunter <jon-hunter@ti.com>
Changes from his patch
- Declare a long as the wait_for_completion_timeout returns long.
Original patch is
http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=ea02cece7b0000bc736e60c4188a11aaa74bc6e6
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently in probe
pm_runtime_put(dev->dev);
...
/* i2c device drivers may be active on return from add_adapter() */
adap->nr = pdev->id;
r = i2c_add_numbered_adapter(adap);
if (r) {
dev_err(dev->dev, "failure adding adapter\n");
goto err_free_irq;
}
...
return 0;
err_free_irq:
free_irq(dev->irq, dev);
err_unuse_clocks:
omap_i2c_write_reg(dev, OMAP_I2C_CON_REG, 0);
pm_runtime_put(dev->dev);
This may access the i2c registers without the clocks in the error cases.
Fix the same by moving the pm_runtime_put after the error check.
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
On OMAP4 we were writing 1 to IRQENABLE_CLR which cleared only
the arbitration lost interrupt. The patch intends to fix the same by writing 0
to the IE register clearing all interrupts.
This is based on the work done by Vikram Pandita <vikram.pandita@ti.com>.
The changes from the original patch ...
- Does not use the IRQENABLE_CLR register to clear as it is not mentioned
to be legacy register IRQENABLE_CLR helps in atomically
setting/clearing specific interrupts, instead use the OMAP_I2C_IE_REG as we
are clearing all interrupts.
Cc: Vikram Pandita <vikram.pandita@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Currently the i2c driver calls the pm_runtime_enable and never
the disable. This may cause a warning when pm_runtime_enable
checks for the count match.Fix the same by calling
pm_runtime_disable in the error and the remove path.
Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The functions omap_i2c_unidle/idle are called from omap_i2c_runtime_resume
and omap_i2c_runtime_suspend which is compiled for CONFIG_PM_RUNTIME.
This patch removes the omap_i2c_unidle/idle functions and folds them
into the runtime callbacks.
This fixes the below warn when CONFIG_PM_RUNTIME is not defined
CC arch/arm/mach-omap2/board-ti8168evm.o
drivers/i2c/busses/i2c-omap.c:272: warning: 'omap_i2c_unidle' defined but not used
drivers/i2c/busses/i2c-omap.c:293: warning: 'omap_i2c_idle' defined but not used
CC net/ipv4/ip_forward.o
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Some drivers (in particular for TV cards) need exclusive access to
their I2C buses for specific operations. Export an unlocked flavor
of i2c_transfer to give them full control.
The unlocked flavor has the following limitations:
* Obviously, caller must hold the i2c adapter lock.
* No debug messages are logged. We don't want to log messages while
holding a rt_mutex.
* No check is done on the existence of adap->algo->master_xfer. It
is thus the caller's responsibility to ensure that the function is
OK to call.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use clk_prepare/clk_unprepare as required by the generic clk framework.
Cc: w.sang@pengutronix.de
Cc: linux-i2c@vger.kernel.org
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This is useful for SoCs whose I2C module's signals can be routed to
different sets of pins at run-time, using the pinctrl API.
+-----+ +-----+
| dev | | dev |
+------------------------+ +-----+ +-----+
| SoC | | |
| /----|------+--------+
| +---+ +------+ | child bus A, on first set of pins
| |I2C|---|Pinmux| |
| +---+ +------+ | child bus B, on second set of pins
| \----|------+--------+--------+
| | | | |
+------------------------+ +-----+ +-----+ +-----+
| dev | | dev | | dev |
+-----+ +-----+ +-----+
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Since there are uses for I2C_M_NOSTART which are much more sensible and
standard than most of the protocol mangling functionality (the main one
being gather writes to devices where something like a register address
needs to be inserted before a block of data) create a new I2C_FUNC_NOSTART
for this feature and update all the users to use it.
Also strengthen the disrecommendation of the protocol mangling while we're
at it.
In the case of regmap-i2c we remove the requirement for mangling as
I2C_M_NOSTART is the only mangling feature which is being used.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
As the bus driver side implementation of I2C_M_RECV_LEN is heavily
tied to SMBus, we can't support received length over 32 bytes, but
let's at least support that.
In practice, the caller will have to setup a buffer large enough to
cover the case where received length byte has value 32, so minimum
32 + 1 = 33 bytes, possibly more if there is a fixed number of bytes
added for the specific slave (for example a checksum.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Douglas Gilbert <dgilbert@interlog.com>
Pull i2c-embedded changes from Wolfram Sang:
"Major changes:
- lots of devicetree additions for existing drivers. I tried hard to
make sure the bindings are proper. In more complicated cases, I
requested acks from people having more experience with them than
me. That took a bit of extra time and also some time went into
discussions with developers about what bindings are and what not.
I have the feeling that the workflow with bindings should be
improved to scale better. I will spend some more thought on
this...
- i2c-muxes are succesfully used meanwhile, so we dropped
EXPERIMENTAL for them and renamed the drivers to a standard pattern
to match the rest of the subsystem. They can also be used with
devicetree now.
- ixp2000 was removed since the whole platform goes away.
- cleanups (strlcpy instead of strcpy, NULL instead of 0)
- The rest is typical driver fixes I assume.
All patches have been in linux-next at least since v3.4-rc6."
Fixed up trivial conflict in arch/arm/mach-lpc32xx/common.c due to the
same patch already having come in through the arm/soc trees, with
additional patches on top of it.
* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (35 commits)
i2c: davinci: Free requested IRQ in remove
i2c: ocores: register OF i2c devices
i2c: tegra: notify transfer-complete after clearing status.
I2C: xiic: Add OF binding support
i2c: Rename last mux driver to standard pattern
i2c: tegra: fix 10bit address configuration
i2c: muxes: rename first set of drivers to a standard pattern
of/i2c: implement of_find_i2c_adapter_by_node
i2c: implement i2c_verify_adapter
i2c-s3c2410: Add HDMIPHY quirk for S3C2440
i2c-s3c2410: Rework device type handling
i2c: muxes are not EXPERIMENTAL anymore
i2c/of: Automatically populate i2c mux busses from device tree data.
i2c: Add a struct device * parameter to i2c_add_mux_adapter()
of/i2c: call i2c_verify_client from of_find_i2c_device_by_node
i2c: designware: Add clk_{un}prepare() support
i2c: designware: add PM support
i2c: ixp2000: remove driver
i2c: pnx: add device tree support
i2c: imx: don't use strcpy but strlcpy
...
These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WeDQ
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree conversions (part 2) from Olof Johansson:
"These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier."
Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
...
A number of devices are using a common register layout, this adds support
code for it in lib/stmp_device.c so we do not need to duplicate it in
each driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=VHLM
-----END PGP SIGNATURE-----
Merge tag 'stmp-dev' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc stmp-dev library code from Olof Johansson:
"A number of devices are using a common register layout, this adds
support code for it in lib/stmp_device.c so we do not need to
duplicate it in each driver."
Fix up trivial conflicts in drivers/i2c/busses/i2c-mxs.c and
lib/Makefile
* tag 'stmp-dev' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
i2c: mxs: use global reset function
lib: add support for stmp-style devices
Pull powerpc updates from Benjamin Herrenschmidt:
"Here are the powerpc goodies for 3.5. Main highlights are:
- Support for the NX crypto engine in Power7+
- A bunch of Anton goodness, including some micro optimization of our
syscall entry on Power7
- I converted a pile of our thermal control drivers to the new i2c
APIs (essentially turning the old therm_pm72 into a proper set of
windfarm drivers). That's one more step toward removing the
deprecated i2c APIs, there's still a few drivers to fix, but we are
getting close
- kexec/kdump support for 47x embedded cores
The big missing thing here is no updates from Freescale. Not sure
what's up here, but with Kumar not working for them anymore things are
a bit in a state of flux in that area."
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (71 commits)
powerpc: Fix irq distribution
Revert "powerpc/hw-breakpoint: Use generic hw-breakpoint interfaces for new PPC ptrace flags"
powerpc: Fixing a cputhread code documentation
powerpc/crypto: Enable the PFO-based encryption device
powerpc/crypto: Build files for the nx device driver
powerpc/crypto: debugfs routines and docs for the nx device driver
powerpc/crypto: SHA512 hash routines for nx encryption
powerpc/crypto: SHA256 hash routines for nx encryption
powerpc/crypto: AES-XCBC mode routines for nx encryption
powerpc/crypto: AES-GCM mode routines for nx encryption
powerpc/crypto: AES-ECB mode routines for nx encryption
powerpc/crypto: AES-CTR mode routines for nx encryption
powerpc/crypto: AES-CCM mode routines for nx encryption
powerpc/crypto: AES-CBC mode routines for nx encryption
powerpc/crypto: nx driver code supporting nx encryption
powerpc/pseries: Enable the PFO-based RNG accelerator
powerpc/pseries/hwrng: PFO-based hwrng driver
powerpc/pseries: Add PFO support to the VIO bus
powerpc/pseries: Add pseries update notifier for OFDT prop changes
powerpc/pseries: Add new hvcall constants to support PFO
...
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game of
booting using device trees, which is a great step forward for them. at91
and spear have pretty much completed this process with a huge amount of
work being put into at91. The other platforms are continuing the process.
We finally start to see the payback on this investment, as new machines
are getting supported purely by adding a .dts source file that can be
completely independent of the kernel source.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7DYv
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull device tree conversions for arm-soc, part 1, from Olof Johansson:
"The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game
of booting using device trees, which is a great step forward for them.
at91 and spear have pretty much completed this process with a huge
amount of work being put into at91. The other platforms are
continuing the process.
We finally start to see the payback on this investment, as new
machines are getting supported purely by adding a .dts source file
that can be completely independent of the kernel source."
Fix up trivial conflict in arch/arm/Kconfig
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
ARM: ux500: Enable PRCMU Timer 4 (clocksource) for Device Tree
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: Fork cpu-db8500 platform_devs for sequential DT enablement
ARM: ux500: Do not attempt to register non-existent i2c devices on Snowball
ARM: SPEAr3xx: Correct keyboard data passed from DT
...
That old mail address doesnt exist any more.
This changes all occurences to my new address.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add device tree probe support for i2c-mxs driver. So far, it's only
been tested on imx28.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
The freed IRQ is not necessary the one requested in probe.
Even if it was, with two or more i2c-controllers it will fails anyway.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable@kernel.org
Call of_i2c_register_devices() in probe function to register i2c devices
specified in the device tree or OF.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
[wsa: add proper braces]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The notification of the transfer complete by calling complete()
should be done after clearing all interrupt status.
This avoids the race condition of misconfigure the i2c controller
in multi-core environment.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: stable@kernel.org
Update the MAINTAINERS entry and all other references accordingly.
Based on an original patch by Wolfram Sang.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Peter Korsgaard <peter.korsgaard@barco.com>
[wsa: fixed merge conflict due to rework in i2c_add_mux_adapter()]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
The slave address of device to be configured in packet
header as follows:
7 bit address: PacketHeader3[7:1]
10 bit address: PacketHeader3[9:0]
Fixing the code to make packet header3 properly.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Apply a naming pattern like in the rest of the subsystem to a first set
of mux drivers. Those drivers are the low-hanging fruit; we want to pick
them to motivate upcoming drivers to follow the new pattern. The missing
GPIO driver will be converted in a later patch.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com> (pca9541)
Acked-by: Jean Delvare <khali@linux-fr.org>
This converts a struct device * to a struct i2c_adapter * while verifying
that the device really is an I2C adapter. Just like i2c_verify_client.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
This patch adds support for s3c2440 I2C bus controller dedicated HDMIPHY device on
Exynos4 platform. Some quirks are introduced due to differences between HDMIPHY
and other I2C controllers on Exynos4. These differences are:
- no GPIOs, HDMIPHY is inside the SoC and the controller is connected
internally
- due to unknown reason (probably HW bug in HDMIPHY and/or the controller) a
transfer fails to finish. The controller hangs after sending the last byte,
the workaround for this bug is resetting the controller after each transfer
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Tested-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Reorganize driver a bit to better handle device tree-based systems:
- move machine type to driver's private structure instead of
quering platform device variants in runtime
- replace s3c24xx_i2c_type enum with unsigned int that holds
bitmask with revision-specific quirks
Signed-off-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
We got multiple patches to add mux support to device tree, so people are
using it happily already and build up on it. I also used it in a project
without encountering problems. 20 months of EXPERIMENTAL should do for
this.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Michael Lawnick <ml.lawnick@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: David Daney <ddaney.cavm@gmail.com>
For 'normal' i2c bus drivers, we can call of_i2c_register_devices()
and have the device tree framework automatically populate the bus with
the devices specified in the device tree.
This patch adds a common code to the i2c mux framework to have the mux
sub-busses be populated by the of_i2c_register_devices() too. If the
mux device has an of_node, we populate the sub-bus' of_node so that
the subsequent call to of_i2c_register_devices() will find the
corresponding devices.
It seemed better to put this logic in i2c_add_mux_adapter() rather
than the individual mux drivers, as they will all probably want to do
the same thing.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Lars-Peter Clausen <lars@metafoo.de>
[wsa: removed superfluous ret-variable and fixed a typo in a comment]
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
