In commit 54328e6404 ("rtlwifi: rtl8821ae: Fix system lockups on boot"),
an attempt was made to fix a regression introduced in commit 1277fa2ab2
("rtlwifi: Remove the clear interrupt routine from all drivers").
Unfortunately, there were logic errors in that patch that prevented
affected boxes from booting even after that patch was applied.
The actual cause of the original problem is unknown as none of the
developers have systems that are affected.
Fixes: 54328e6404 ("rtlwifi: rtl8821ae: Fix system lockups on boot")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V4.1+]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
commit a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
moved send completion polling under HTT Rx (CE 5) service routine. For
QCA6174 based devices copy engine 1 (CE 1) is used for HTT Rx instead
of CE 5. So send completion never be called. This is causing "failed to
transmit packet, dropping: -105" errors. Fix this by processing send
completion from CE 1 service routine instead of CE 5.
Fixes: a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
Tested-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Be a little bit more careful when dereferencing sta on key removal,
As it might already get flushed on other thread.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When entering D3, we need to use hardcoded key indices because the
firmware requires that. To do so, we are overwriting the HW key index
in the keyconf structure, which makes it impossible to reuse the
indices that were used before entering D3. Additionally, we overwrite
all the non-PTK keys with index 1, because the firmware only allows
one non-PTK key to be set. This is bad, because when we resume, we
may try to set more than one key with index 1, which will obviously
fail.
To fix this, allow the callers to set a pre-defined index to use in
iwl_mvm_set_sta_key() instead of relying on the hw_key_idx value from
the keyconf struct (which requires overwriting it). In normal cases,
the caller can pass STA_KEY_IDX_INVALID, which will cause a new key
offset to be chosen. During HW_RESTART, we pass the offset that is in
use. And during D3 entry, we pass the hardcoded indices we need to
use.
Additionally, don't clear the fw_key_table in D3 entry, so that the
flags are still set with the pre-D3 values when exiting D3.
fixes=I3165c22362483f0152d9ec1d2a987fb5529727c1
Fixes: b546dcd6b7 ("iwlwifi: mvm: don't reset key index on HW restart")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add some new PCI IDs for the 8260 series which were missing.
The following sub-system IDs were added:
0x0130, 0x1130, 0x0132, 0x1132, 0x1150, 0x8110, 0x9110, 0x8130,
0x9130, 0x8132, 0x9132, 0x8150, 0x9150, 0x0044, 0x0930
CC: <stable@vger.kernel.org> [4.1+]
Signed-off-by: Oren Givon <oren.givon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Commit a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
introduced to use the unused CE5 for target to host message. For the device
like QCA6174, CE5 already assigned for other feature. So for QCA6174, override
the CE5 configuration and use the CE1 instead.
This patch is based on Rajkumar's earlier patch.
Fixes: a70587b338 ("ath10k: configure copy engine 5 for HTT messages")
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add new BMI target version and chip id revision. Register it
on supported chips list.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A follow up patch introducing a QCA9377 hw1.0 support will need
this device identification helper for an explicit distinction of
HWs, as apparently both QCA6174 hw3.0 and QCA9377 share the same BMI
target version (0x0502000x). For the QCA9377 hw1.1 previously
added we were just lucky we did not overlap with the same chip_id_rev.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The uart_pin was incorrectly configured for QCA9377
and the recently added hw_params were omitted.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When introducing the original QCA9377 support, the chip target
version was wrongly picked. The chip advertising itself with
bmi target value equal to 0x05020001 is in fact a 1.1 revision.
I realized this once I got a real 1.1 hw to play with.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The number of spatial streams that are derived from chain mask
for 4x4 devices is using wrong bitmask and conditional check.
This is affecting downlink throughput for QCA99x0 devices. Earlier
cfg_tx_chainmask is not filled by default until user configured it
and so get_nss_from_chainmask never be called. This issue is exposed
by recent commit 166de3f189 ("ath10k: remove supported chain mask").
By default maximum supported chain mask is filled in cfg_tx_chainmask.
Cc: stable@vger.kernel.org
Fixes: 5572a95b4b ("ath10k: apply chainmask settings to vdev on creation")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Switch everything to the new and more capable implementation of abs().
Mainly to give the new abs() a bit of a workout.
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWOehzAAoJECTWi3JdVIfQTPYH+wYMDG8gAIw2s0AJ4DvVe4qZ
sOAm1UgUJZxssrEA6BNqbfM0dfRo+oQJKmRd0Dc5n7LEMsYHdI/5yKHk8PCS6ZzD
iQyQCzbd0thDAqwuPaMP62cyPDHwyJX22VGTsgVnj6AZqAQ+9+g4SPKhFnm1Mlm4
hmDi6fdSrsqo8k8gkpVN8RFOfVsjAV1dLtAauQRWDHrqMxXURSrKG76eqAqUa5bn
BLPXBoj5PA0DMLPO2j+ADZwWN723LrI2mSSlc+ThjEX/OIt2OhAoiOTV5RPqaafy
TIsCkh68q/gYAsL5HtvvmgZByl41FLYiO0Z+rXmWUyMMbnvhZTLws9S2BNpBLuk=
=DgXG
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"Quite a lot of activity in SPI this cycle, almost all of it in drivers
with a few minor improvements and tweaks in the core.
- Updates to pxa2xx to support Intel Broxton and multiple chip selects.
- Support for big endian in the bcm63xx driver.
- Multiple slave support for the mt8173
- New driver for the auxiliary SPI controller in bcm2835 SoCs.
- Support for Layerscale SoCs in the Freescale DSPI driver"
* tag 'spi-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (87 commits)
spi: pxa2xx: Rework self-initiated platform data creation for non-ACPI
spi: pxa2xx: Add support for Intel Broxton
spi: pxa2xx: Detect number of enabled Intel LPSS SPI chip select signals
spi: pxa2xx: Add output control for multiple Intel LPSS chip selects
spi: pxa2xx: Use LPSS prefix for defines that are Intel LPSS specific
spi: Add DSPI support for layerscape family
spi: ti-qspi: improve ->remove() callback
spi/spi-xilinx: Fix race condition on last word read
spi: Drop owner assignment from spi_drivers
spi: Add THIS_MODULE to spi_driver in SPI core
spi: Setup the master controller driver before setting the chipselect
spi: dw: replace magic constant by DW_SPI_DR
spi: mediatek: mt8173 spi multiple devices support
spi: mediatek: handle controller_data in mtk_spi_setup
spi: mediatek: remove mtk_spi_config
spi: mediatek: Update document devicetree bindings to support multiple devices
spi: fix kernel-doc warnings about missing return desc in spi.c
spi: fix kernel-doc warnings about missing return desc in spi.h
spi: pxa2xx: Align a few defines
spi: pxa2xx: Save other reg_cs_ctrl bits when configuring chip select
...
Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch of
debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6ePQACgkQMUfUDdst+ymNTgCgpP0CZw57GpwF/Hp2L/lMkVeo
Kx8AoKhEi4iqD5fdCQS9qTfomB+2/M6g
=g7ZO
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch
of debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time"
* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Add debugfs_create_ulong()
of: to support binding numa node to specified device in devicetree
debugfs: Add read-only/write-only bool file ops
debugfs: Add read-only/write-only size_t file ops
debugfs: Add read-only/write-only x64 file ops
debugfs: Consolidate file mode checks in debugfs_create_*()
Revert "mm: Check if section present during memory block (un)registering"
driver-core: platform: Provide helpers for multi-driver modules
mm: Check if section present during memory block (un)registering
devres: fix a for loop bounds check
CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
base/platform: assert that dev_pm_domain callbacks are called unconditionally
sysfs: correctly handle short reads on PREALLOC attrs.
base: soc: siplify ida usage
kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
kobject: explain what kobject's sd field is
debugfs: document that debugfs_remove*() accepts NULL and error values
debugfs: Pass bool pointer to debugfs_create_bool()
ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
This supports a way to get target stats through normal
ethtool stats API.
For instance:
# ethtool -S wlan1
NIC statistics:
tx_pkts_nic: 353
tx_bytes_nic: 25142
rx_pkts_nic: 6
rx_bytes_nic: 996
d_tx_ucast_pkts: 89
d_tx_bcast_pkts: 264
d_tx_ucast_bytes: 3020
d_tx_bcast_bytes: 22122
...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This will allow us to call it from elsewhere when implementing
ethtool stats.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Improper use of strlcpy caused garbage to be appended to the
firmware version string. Fix this by paying attention to the
ie_lenth.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It can take a user a while to understand why their
NIC that advertises 802.11n support cannot actually
do 802.11n. Print out a warning in the logs to save
the next poor person to use this NIC some trouble.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This lets 'iw phy phy0 info' report antennas for
the radio device:
...
Available Antennas: TX 0x2 RX 0x2
Configured Antennas: TX 0x2 RX 0x2
...
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When configuring Tx vring for new connection,
WMI call to the firmware may fail. In this case, need to
clean up properly. In particular, need to call
cfg80211_del_sta() in case of AP like interface.
Perform full "disconnect" procedure for proper clean up
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adjust driver behavior during FW boot. Proper sequence of
events after reset and FW download, is as following:
- FW prepares mailbox structure and reports IRQ "FW_READY"
- driver caches mailbox registers, marks mailbox readiness
- FW sends WMI_FW_READY event, ignore it
- FW sends WMI_READY event with some data
- driver stores relevant data marks FW is operational
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When Tx ring full is encountered with TSO,
printout of "DMA error" was wrongly printed.
In addition, in case of Tx ring full return
proper error code so that NETDEV_TX_BUSY is
returned to network stack in order not to
drop the packets and retry transmission of the
packets when ring is emptied.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some events are ignored for purpose; such events should not
be treated as "unhandled events". Replace info message
saying "unhandled" with debug one saying "ignore", to reduce
dmesg pollution
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the hardware name, revision and update the pci_id table.
Currently there're two HW ref. designs available I'm aware of,
with 1.0.2 and 1.1 chip revisions. I've access and been using
the first one so far and this patch cover only it.
QCA9377 inherits most of the stuff (e.g. fw interfaces)
from QCA61x4 design, so the integration was pretty straightforward.
Signed-off-by: Bartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
To reflect configured antenna settings in HT/VHT MCS map,
reload the HT/VHT capabilities upon antenna change.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Move HT and VHT capabiltity setup static functions to avoid
forward declaration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
HT/VHT MCS rateset should be filled only for configured chainmask
rather that max supported chainmask. Fix that by checking configured
chainmask while filling HT/VHT MCS rate map.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Removing supported chainmask fields as it can be always derived
from num_rf_chains.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For the messages from host to target, shadow copy of CE descriptors
are maintained in source ring. Before writing actual CE descriptor,
first shadow copy is filled and then it is copied to CE address space.
To optimize in download path and to reduce d-cache pressure, removing
shadow copy of CE descriptors. This will also reduce driver memory
consumption by 33KB during on device probing.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. ath10k doesn't rely on the meta/transfer_id
when handling send completion (htc ep id is stored in sk_buff control
buffer). So the unused output arguments {bufferp, nbytesp and transfer_idp}
are removed from CE send completion. This change is needed before removing
the shadow copy of copy engine (CE) descriptors in follow up patch.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CE diag window access is serialized (it has to be by design) so
there's no way to get a different send completion. so there's no
need for post completion validation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently to avoid uncached memory access while filling up copy engine
descriptors, shadow descriptors are used. This can be optimized further
by removing shadow descriptors. To achieve that first shadow ring
dependency in ce_send is removed by creating local copy of the
descriptor on stack and make a one-shot copy into the "uncached"
descriptor.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds support for getting firmware debug stats in 10.4 fw.
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add WMI-TLV and FW API support in ath10k testmode.
Ath10k can get right wmi command format from UTF image
to communicate UTF firmware.
Signed-off-by: Alan Liu <alanliu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
European Union has made it mandatory that all devices working in 2.4 GHz
has to adhere to the ETSI specification (ETSI EN 300 328 V1.9.1)
beginnig this year. The standard basically speaks about interferences
in 2.4Ghz band.
For example, when 802.11 device detects interference, TX must be stopped
as long as interference is present.
Adaptive CCA is a feature, when enabled the device learns from the
environment and configures CCA levels adaptively. This will improve
detecting interferences and the device can stop trasmissions till the
interference is present eventually leading to good performances in
varying interference conditions.
The patch includes code for enabling adaptive CCA for 10.2.4 firmware on
QCA988X.
Signed-off-by: Maharaja <c_mkenna@qti.qualcomm.com>
Signed-off-by: Manikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ssb bus can be found on various "host" devices like PCI/PCMCIA/SDIO.
Every ssb bus contains cores AKA devices.
The main idea is to have ssb driver scan/initialize bus and register
ready-to-use cores. This way ssb drivers can operate on a single core
mostly ignoring underlaying details.
For some reason PCMCIA support was split between ssb and b43. We got
PCMCIA host device probing in b43, then bus scanning in ssb and then
wireless core probing back in b43. The truth is it's very unlikely we
will ever see PCMCIA ssb device with no 802.11 core but I still don't
see any advantage of the current architecture.
With proposed change we get the same functionality with a simpler
architecture, less Kconfig symbols, one killed EXPORT and hopefully
cleaner b43. Since b43 supports both: ssb & bcma I prefer to keep ssb
specific code in ssb driver.
This mostly moves code from b43's pcmcia.c to bridge_pcmcia_80211.c. We
already use similar solution with b43_pci_bridge.c. I didn't use "b43"
in name of this new file as in theory any driver can operate on wireless
core.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In uap mode the carrier is not enabled until after the first STA joins.
The carrier triggers the bridge to start its state machine, and if STP
is enabled, it takes 4 seconds as it transitions from disabled to
forwarding. During this time the bridge drops all traffic, and the EAPOL
handshake times out after 3 seconds, preventing stations from joining.
Follow the logic used in mac80211 and start the carrier in start_ap
and disable it in stop_ap. This has a nice benefit of allowing the
first station connection time to be reduced by up to 75% when STP is
in use.
Signed-off-by: Martin Faltesek <mfaltesek@google.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wcn36xx implements a ring buffer for transmitted frames for each
(high and low priority) DMA channel. The ring buffers are lockless:
new frames are inserted at the head of the queue, while finished
packets are reaped from the tail.
Unfortunately, the list manipulations are missing any kind of barriers
so are susceptible to various races: for example, a TX completion
handler might read an updated desc->ctrl before the head has actually
advanced, and then null out the ctl->skb pointer while it is still
being used in the TX path.
Simplify things here by adding a spin lock when traversing the ring.
This change increased stability for me without adding any noticeable
overhead on my platform (xperia z).
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some of the ath9k_phyerr enums were wrong from the
beginning (and even before). Most of the time the
codes were used for counters to be displayed over
debugfs, which made this a non-functional issue.
Some (e.g. ATH9K_PHYERR_FALSE_RADAR_EXT) are used
for radar detection and require the correct code
to work as intended.
This patch includes:
a) fixes
ATH9K_PHYERR_FALSE_RADAR_EXT: 24 => 36
ATH9K_PHYERR_CCK_LENGTH_ILLEGAL: 32 => 28
ATH9K_PHYERR_CCK_POWER_DROP: 33 => 29
ATH9K_PHYERR_HT_CRC_ERROR: 34 => 32
ATH9K_PHYERR_HT_LENGTH_ILLEGAL: 35 => 33
ATH9K_PHYERR_HT_RATE_ILLEGAL: 36 => 34
b) extensions
ATH9K_PHYERR_CCK_BLOCKER = 24
ATH9K_PHYERR_HT_ZLF = 35
ATH9K_PHYERR_GREEN_FIELD = 37
Aside from the correction and completion made in
the enum, the patch also extends the display of
the related counters in the debugfs.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current code exits after alloc_orinocodev, but fails to change the
return value to something that indicates the failure. This patch
changes the return value to -ENOMEM.
https://bugzilla.kernel.org/show_bug.cgi?id=106181
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SIOCSIWAP (airo_set_wap) affects scan: only the AP specified by
SIOCSIWAP is present in scan results.
This makes NetworkManager work for the first time but then unable to
find any other APs.
Clear APList before starting scan and set it back after scan completes
to work-around the problem.
To avoid losing packets during scan, modify disable_MAC() to omit
netif_carrier_off() call when lock == 2.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of dynamically allocating APList, make it a member of struct
airo_info to always track state of APList_rid.
This simplifies suspend/resume and allows removal of readAPListRid.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* fixes and cleanups in scan
* support of several scan plans
* improvements in FTM
* fixes in FW API
* improvements in the failure paths when the bus is dead
* other various small things here and there
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=a6Vu
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-10-25' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* bug fix for TDLS
* fixes and cleanups in scan
* support of several scan plans
* improvements in FTM
* fixes in FW API
* improvements in the failure paths when the bus is dead
* other various small things here and there
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJWLzQ5AAoJEG4XJFUm622btRwH/A6fS7p5uSZzH5lIU8ZBLc7X
MzC1jYVepHXaR5+OhBIbQ5oSo47Y4xqMeO2ylFMpUSg4vntqR9yZNVH2lXV5EfPB
fIaGYIsb3ExjAFoIjFUBwqSOB7CCZK5myk+SLiOu9XghjsLObP5JLKgA49PGhFRn
CCuDq9diDNeJBnVzTS1ms5wO6RmOBiizzjbu7adJI0Hu63z2+P4pNMG4Zz6E1z97
z8DRFEwdNN9gKHIaEC61h7ZT9XDB/Tj31Wl3Irbi4GBS7sRXnFK46FYU8fMVDbDZ
ykj05sq6nTrfwfVZtXbV3SxlYNSN4SFFRuskon6IUcIzlNTuIULgvlpCjJJ6tyQ=
=pFoQ
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-10-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
here's a bigger pull request for 4.4. The diffstat looks scary as we
created a new directory realtek for all realtek drivers. In the future
I'm planning to create similar directories for all vendors, currently we
just have ath, mediatek and realtek. This change has been in linux-next
for a couple of weeks so it should be safe, but of course you never
know.
There's also a new driver rtl8xxxu for few realtek USB devices. This
just made it to the last linux-next build.
Otherwise there's nothing really special, more info below. If time
permits, and it's ok for you, I'm hoping to send you a one more pull
request this week.
brcmfmac
* using netdev carrier state
* add and rework some cfg80211 callbacks mainly for AP mode
* use devcoredump when triggered by firmware event
realtek
* create new directory drivers/net/wireless/realtek/ for all realtek
drivers, not visible to users (no kconfig changes etc)
* add rtl8xxxu, a new mac80211 driver for RTL8723AU, RTL8188CU,
RTL8188RU, RTL8191CU, RTL8192CU and hopefully more in the future
ath10k
* add board 2 API support for automatically choosing correct board file
* data path optimisations
* disable PCI power save for qca988x and QCA99x0 due to interop reasons
wil6210
* BlockAckReq support
* firmware crashdump using devcoredump
* capture all frames with sniffer
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
