We already have dev->scancode_filter and dev->scancode_wakeup_filter
so rename dev->scanmask to dev->scancode_mask for consistency.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The basic API of rc-core used to be:
dev = rc_allocate_device();
dev->x = a;
dev->y = b;
dev->z = c;
rc_register_device();
which is a pretty common pattern in the kernel, after the introduction of
protocol arrays the API looks something like:
dev = rc_allocate_device();
dev->x = a;
rc_set_allowed_protocols(dev, RC_BIT_X);
dev->z = c;
rc_register_device();
There's no real need for the protocols to be an array, so change it
back to be consistent (and in preparation for the following patches).
[m.chehab@samsung.com: added missing changes at some files]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This driver codes the two address bytes in reverse order when compared to the
other drivers, so make it consistent (and update the keymap, note that the
result is a prefix change from 0x6b86 -> 0x866b, and the latter is pretty
common among the NECX keymaps. While not conclusive, it's still a strong hint
that the change is correct).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Right now the protocol information is not preserved, rc-core gets handed a
scancode but has no idea which protocol it corresponds to.
This patch (which required reading through the source/keymap for all drivers,
not fun) makes the protocol information explicit which is important
documentation and makes it easier to e.g. support multiple protocols with one
decoder (think rc5 and rc-streamzap). The information isn't used yet so there
should be no functional changes.
[m.chehab@samsung.com: rebased, added cxusb and removed bad whitespacing]
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The arguments used for ir-kbd-i2c's get_key() functions are not
really suited for rc-core and the ir_raw/ir_key distinction is
just confusing.
Convert all of them to return a protocol/scancode/toggle triple instead.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The bt8xx driver does RC5 decoding for Nebula digi hardware, but includes
some pointless limitations (both start bits must be one, the
device/address/system must be 0x00). Remove those limitations and update
the keymap to use the full RC5 scancode (fortunately the 0x00 address
means that this is perfectly backwards compatible).
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Now that the custom motion detection API has been replaced with a
standard API there is no reason anymore to keep it in staging.
So (finally!) move it to drivers/media/pci.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
* .: (268 commits)
Linux 3.16-rc6
um: segv: Save regs only in case of a kernel mode fault
um: Fix hung task in fix_range_common()
um: Ensure that a stub page cannot get unmapped
Revert "um: Fix wait_stub_done() error handling"
btrfs: test for valid bdev before kobj removal in btrfs_rm_device
Btrfs: fix abnormal long waiting in fsync
random: check for increase of entropy_count because of signed conversion
ARM: EXYNOS: Fix core ID used by platsmp and hotplug code
ahci: add support for the Promise FastTrak TX8660 SATA HBA (ahci mode)
ARM: at91/dt: add missing clocks property to pwm node in sam9x5.dtsi
ARM: at91/dt: fix usb0 clocks definition in sam9n12 dtsi
ARM: at91: at91sam9x5: correct typo error for ohci clock
irqchip: gic: Fix core ID calculation when topology is read from DT
GFS2: fs/gfs2/rgrp.c: kernel-doc warning fixes
GFS2: memcontrol: Spelling s/invlidate/invalidate/
GFS2: Allow caching of glocks for flock
GFS2: Allow flocks to use normal glock dq rather than dq_wait
GFS2: replace count*size kzalloc by kcalloc
GFS2: Use GFP_NOFS when allocating glocks
...
Conflicts:
drivers/media/dvb-frontends/si2168.c
drivers/media/dvb-frontends/si2168_priv.h
drivers/media/tuners/si2157.c
The ZR050_MO_COMP define is cut and pasted twice so we can delete the
second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch removes the null test on dvb. dvb is initialized at the
beginning of the function to &port->dvb. Since port is dereferenced
prior to the null test, port must be a valid pointer, and
&port->dvb cannot be null.
The following Coccinelle script is used for detecting the change:
@r@
expression e,f;
identifier g,y;
statement S1,S2;
@@
*e = &f->g
<+...
f->y
...+>
*if (e != NULL || ...)
S1 else S2
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for Hauppauge model 71100: WinTV-ImpactVCB-e
(PCIe, Retail, half height)
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The v4l2_pix_format structure has no reserved field. It is embedded in
the v4l2_framebuffer structure which has no reserved fields either, and
in the v4l2_format structure which has reserved fields that were not
previously required to be zeroed out by applications.
To allow extending v4l2_pix_format, inline it in the v4l2_framebuffer
structure, and use the priv field as a magic value to indicate that the
application has set all v4l2_pix_format extended fields and zeroed all
reserved fields following the v4l2_pix_format field in the v4l2_format
structure.
The availability of this API extension is reported to userspace through
the new V4L2_CAP_EXT_PIX_FORMAT capability flag. Just checking that the
priv field is still set to the magic value at [GS]_FMT return wouldn't
be enough, as older kernels don't zero the priv field on return.
To simplify the internal API towards drivers zero the extended fields
and set the priv field to the magic value for applications not aware of
the extensions.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rather than having two unions for all types just keep 'val' and
'cur.val' and use the p_cur and p_new unions to access all others.
The only reason for keeping 'val' and 'cur.val' is that it is used
all over, so converting this as well would be a huge job.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Since all the drivers that use `struct v4l2_fh' use the core
priority checking, the setting of the flag in the drivers can
be removed.
Signed-off-by: Ramakrishnan Muthukrishnan <ramakrmu@cisco.com>
Reviewed-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The CX18_ALSA_DBGFLG_WARN is cut and pasted twice and we can delete the
second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch remove variables that are initialized with a constant,
are never updated, and are only used as parameter of return.
Return the constant instead of using a variable.
Verified by compilation only.
The coccinelle script that find and fixes this issue is:
// <smpl>
@@
type T;
constant C;
identifier ret;
@@
- T ret = C;
... when != ret
when strict
return
- ret
+ C
;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The saa7134 driver uses core-locking, so there is no longer any need
to use the ioctl op instead of the unlocked_ioctl op. This change
was forgotten for the saa7134-empress.c, so fix this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
This were reported several times, like:
drivers/built-in.o: In function `cxusb_dualdig4_rev2_tuner_attach':
>> cxusb.c:(.text+0x27d4b5): undefined reference to `dib7000p_get_i2c_master'
drivers/built-in.o: In function `dib7070_set_param_override':
cxusb.c:(.text+0x27d5a5): undefined reference to `dib0070_wbd_offset'
>> cxusb.c:(.text+0x27d5be): undefined reference to `dib7000p_set_wbd_ref'
drivers/built-in.o: In function `dib7070_tuner_reset':
>> cxusb.c:(.text+0x27d5f9): undefined reference to `dib7000p_set_gpio'
drivers/built-in.o: In function `cxusb_dualdig4_rev2_frontend_attach':
>> cxusb.c:(.text+0x27df5c): undefined reference to `dib7000p_i2c_enumeration'
In this specific report:
CONFIG_DVB_USB_CXUSB=y
CONFIG_DVB_DIB7000P=m
But the same type of bug can happen if:
CONFIG_DVB_DIB7000P=m
and one of the bridge drivers is compiled builtin (cxusb, cx23885-dvb
and/or dib0700).
As a bonus, dib7000p won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with Hauppauge Nova-TD (2 frontends).
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function.
However, the dib7000p initialization can require up to 3
functions to be called:
- dib7000p_get_i2c_master;
- dib7000p_i2c_enumeration;
- dib7000p_init (before this patch dib7000_attach).
(plus a bunch of other functions that the bridge driver will
need to call).
As we need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename the function that probes and init the hardware
to dib7000p_init.
A latter patch will add a new dib7000p_attach that will be
used as originally conceived by dvb_attach() way.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The g_std and s_std operations are video-related, move them to the video
ops where they belong.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is a few conflicts with older symbols on older kernels so we
have to patch this driver when backporting. Instead just make these
routines specific to the driver.
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If the saa7134 module is loaded with the saa7134_userptr set to 1,
then USERPTR support is enabled. A check in buffer_prepare
verifies that the pointer is page-aligned.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Convert the saa7134 driver to vb2.
Note that while this uses the vb2-dma-sg version, the VB2_USERPTR mode is
disabled. The DMA hardware only supports DMAing full pages, and in the
USERPTR memory model the first and last scatter-gather buffer is almost
never a full page.
In practice this means that we can't use the VB2_USERPTR mode.
This has been tested with raw video, compressed video, VBI, radio, DVB and
video overlays.
Unfortunately, a vb2 conversion is one of those things you cannot split
up in smaller patches, it's all or nothing. This patch switches the whole
driver over to vb2, using the vb2 ioctl and fop helper functions.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All dmaqueue's use saa7134_pgtable, so move it into struct saa7134_dmaqueue.
The videobuf_queue priv_data field now points to the dmaqueue struct.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When ivtv PCM device is accessed at the state where no firmware is
loaded, it oopses like:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
IP: [<ffffffffa049a881>] try_mailbox.isra.0+0x11/0x50 [ivtv]
Call Trace:
[<ffffffffa049aa20>] ivtv_api_call+0x160/0x6b0 [ivtv]
[<ffffffffa049af86>] ivtv_api+0x16/0x40 [ivtv]
[<ffffffffa049b10c>] ivtv_vapi+0xac/0xc0 [ivtv]
[<ffffffffa049d40d>] ivtv_start_v4l2_encode_stream+0x19d/0x630 [ivtv]
[<ffffffffa0530653>] snd_ivtv_pcm_capture_open+0x173/0x1c0 [ivtv_alsa]
[<ffffffffa04526f1>] snd_pcm_open_substream+0x51/0x100 [snd_pcm]
[<ffffffffa0452853>] snd_pcm_open+0xb3/0x260 [snd_pcm]
[<ffffffffa0452a37>] snd_pcm_capture_open+0x37/0x50 [snd_pcm]
[<ffffffffa033f557>] snd_open+0xa7/0x1e0 [snd]
[<ffffffff8118a628>] chrdev_open+0x88/0x1d0
[<ffffffff811840be>] do_dentry_open+0x1de/0x270
[<ffffffff81193a73>] do_last+0x1c3/0xec0
[<ffffffff81194826>] path_openat+0xb6/0x670
[<ffffffff81195b65>] do_filp_open+0x35/0x80
[<ffffffff81185449>] do_sys_open+0x129/0x210
[<ffffffff815b782d>] system_call_fastpath+0x1a/0x1f
This patch adds the check of firmware at PCM open callback like other
open callbacks of this driver.
Bugzilla: https://apibugzilla.novell.com/show_bug.cgi?id=875440
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The else statement here is not aligned with the correct if statement.
I think the code works as intended and it's just the indenting which is
wrong. Also kernel style says we should use curly braces here so I have
added those.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Changeset 15e64f0dde broke compilation on several archs, as it
forgot to include vmalloc.h.
drivers/media/pci/saa7134/saa7134-alsa.c: In function ‘saa7134_alsa_dma_init’:
CC [M] drivers/media/rc/keymaps/rc-behold-columbus.o
drivers/media/pci/saa7134/saa7134-alsa.c:283:2: error: implicit declaration of function ‘vmalloc_32’ [-Werror=implicit-function-declaration]
dma->vaddr = vmalloc_32(nr_pages << PAGE_SHIFT);
^
drivers/media/pci/saa7134/saa7134-alsa.c:283:13: warning: assignment makes pointer from integer without a cast [enabled by default]
dma->vaddr = vmalloc_32(nr_pages << PAGE_SHIFT);
^
drivers/media/pci/saa7134/saa7134-alsa.c:296:2: error: implicit declaration of function ‘vzalloc’ [-Werror=implicit-function-declaration]
dma->sglist = vzalloc(dma->nr_pages * sizeof(*dma->sglist));
^
drivers/media/pci/saa7134/saa7134-alsa.c:296:14: warning: assignment makes pointer from integer without a cast [enabled by default]
dma->sglist = vzalloc(dma->nr_pages * sizeof(*dma->sglist));
^
drivers/media/pci/saa7134/saa7134-alsa.c:310:2: error: implicit declaration of function ‘vfree’ [-Werror=implicit-function-declaration]
vfree(dma->sglist);
Add it to avoid such breakages.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is already available from saa7134_dev.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Don't calculate this for every buffer, store it globally instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This will make the next patch a bit easier to read.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
saa7134-alsa used low-level videobuf functions to allocate and sync
DMA buffers. Replace this with saa7134-specific code. These functions
will not be available when we convert to vb2.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Just white space and coding style changes to reduce the noise in the
following patches.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This solves this bug:
https://bugzilla.kernel.org/show_bug.cgi?id=73361
The problem is that when you quit tvtime it calls STREAMOFF, but then it queues a
bunch of buffers for no good reason before closing the file descriptor.
In the past closing the fd would free the vb queue since that was part of the file
handle struct. Since that was moved to the global struct that no longer happened.
This wouldn't be a problem, but the extra QBUF calls that tvtime does meant that
the buffer list in videobuf (q->stream) contained buffers, so REQBUFS would fail
with -EBUSY.
The solution is to init the list head explicitly when releasing the file
descriptor and to not free the video resource when calling streamoff.
The real fix will hopefully go into kernel 3.16 when the vb2 conversion is
merged. Basically the saa7134 driver with the old videobuf is so full of holes it
ain't funny anymore, so consider this a band-aid for kernels 3.14 and 15.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.14 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The vb2 core ignores any return code from the stop_streaming op.
And there really isn't anything it can do anyway in case of an error.
So change the return type to void and update any drivers that implement it.
The int return gave drivers the idea that this operation could actually
fail, but that's really not the case.
The pwc amd sdr-msi3101 drivers both had this construction:
if (mutex_lock_interruptible(&s->v4l2_lock))
return -ERESTARTSYS;
This has been updated to just call mutex_lock(). The stop_streaming op
expects this to really stop streaming and I very much doubt this will
work reliably if stop_streaming just returns without really stopping the
DMA.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds support for the PCI-8604PW card equipped with four 878A.
It is unknown who the manufacturer of this card is and no drivers were
available during development of the patch. According to images found
online, the card is originally sold with Linux DVR software.
A CPLD on the card prevents the 878A from requesting access to the
bus until an initialization sequence has been issued via GPIOs. The
implemented sequence uses the minimum number of GPIOs needed to
successfully unlock bus access. As there are many more GPIOs connected
to the CPLD, it is very likely that some of the others have an influence
on the bus arbitration scheduling. This should be investigated further
in case of performance issues.
The tested card contains an EEPROM on one of the 878A, but it is
completely empty (i.e. contains only 0xff), so it is not possible
to detect the card.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Tested-by: Robert Longbottom <rongblor@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b28 ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9 ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
Do not attempt to reload the tuner modules when resuming after a suspend.
This triggers a WARN_ON in kernel/kmod.c:148 __request_module.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=69581.
This has always been wrong, but it was never noticed until the WARN_ON
was added in 3.9.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: stable@vger.kernel.org # for v3.9 and up
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Static checkers complain about the inconsistent NULL check here.
There is an unchecked dereference of "input->fe" in the call to
tuner_attach_tda18271() and there is a second unchecked dereference a
couple lines later when we do:
input->fe2->tuner_priv = input->fe->tuner_priv;
But actually "intput->fe" can't be NULL because if demod_attach_drxk()
fails to allocate it, then we would have return an error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
ARRAY_SIZE(buf) (8 elements) was intended instead of sizeof(buf) (16
bytes). But this is just a sanity check and the callers always pass
valid values so this doesn't cause a problem.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The allowed and enabled protocol masks need to be expanded to be per
filter type in order to support wakeup filter protocol selection. To
ease that process abstract access to the rc_dev::allowed_protos and
rc_dev::enabled_protocols members with inline functions.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
New board addition. No other changes.
[m.chehab@samsung.com: rebase patch and fix whitespace mangling]
Signed-off-by: Pojar George <geoubuntu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
If a queue was canceled, then the buf_finish op was never called for the
pending buffers. So add this call to queue_cancel. Before calling buf_finish
set the buffer state to PREPARED, which is the correct state. That way the
states DONE and ERROR will only be seen in buf_finish if streaming is in
progress.
Since buf_finish can now be called from non-streaming state we need to
adapt the handful of drivers that actually need to know this.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The buf_finish op should always work, so change the return type to void.
Update the few drivers that use it.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Pawel Osciak <pawel@osciak.com>
Reviewed-by: Pawel Osciak <pawel@osciak.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
When tuning to 10818V on Astra 28E2, the system tunes to 11343V
instead. This is a regression in the S471 driver introduced with the
changeset: b43ea8068d [media] cx23885:
Fix TeVii S471 regression since introduction of ts2020.
Suggested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Joakim Hernberg <jhernberg@alchemy.lu>
Tested-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
