in the previous commit : f1f220ea1dda078, the BUSY state of buffer is wrongly
deleted. this patch just restore it.
Signed-off-by: xiong <xiong@qca.qualcomm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d37204566a.
This change is incorrect, as per Jan Beulich:
====================
But this is wrong from all we can tell, we discussed this before
(Wei pointed to the discussion in an earlier reply). The core of
it is that the put here parallels the one in netbk_tx_err(), and
the one in xenvif_carrier_off() matches the get from
xenvif_connect() (which normally would be done on the path
coming through xenvif_disconnect()).
====================
And a previous discussion of this issue is at:
http://marc.info/?l=xen-devel&m=136084174026977&w=2
Signed-off-by: David S. Miller <davem@davemloft.net>
It advertises a standard CDC-ETHER interface, which actually should be
driven by qmi_wwan.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sets the sysfs device_type to 'bond' for udev. This allows udev rules to
be created for bond devices. This is similar to how other network
devices set their device_type.
Signed-off-by: Doug Goldstein <cardoe@cardoe.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following inconsistencies in bond_release_all:
- IFF_BONDING flag is not stripped from slaves
- MTU is not restored
- no netdev notifiers are sent
Instead of trying to keep bond_release and bond_release_all in sync
I think we can re-use bond_release as the environment for calling it
is correct (RTNL is held). I have been running tests for the past
week and they came out successful. The only way for bond_release to fail
is for the slave to be attached in a different bond or to not be a slave
but that cannot happen as RTNL is held and no slave manipulations can be
achieved.
V2: As suggested bond_release is renamed to __bond_release_one with a
new parameter "all" introduced so to avoid calling unnecessary code while
destroying a bond, and a wrapper for it called bond_release is created
because of ndo_del_link. bond_release_all() is removed.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch b44 always allocates the 2 bytes needed for aligned
access on every platform, now it uses netdev_alloc_skb_ip_align().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
netbk_fatal_tx_err() calls xenvif_carrier_off(), which does
a xenvif_put(). As callers of netbk_fatal_tx_err should only
have one reference to the vif at this time, then the xenvif_put
in netbk_fatal_tx_err is one too many.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check whether the phy-reset GPIO is valid, prior to requesting it.
In the case a board does not provide a phy-reset GPIO, just returns immediately.
With such gpio validation in place, it is also safe to change from pr_debug to
dev_err in the case the gpio request fails.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 3ad machine state spinlock can be used before it is inititialized
while doing bond_enslave() (and the port is being initialized) since
port->slave is set before the lock is prepared, thus causing soft
lock-ups and a multitude of other nasty bugs.
[ Rename __initialize_port_locks() variable name to 'slave' -DaveM ]
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
port->slave can be NULL since it's being initialized in bond_enslave
thus dereferencing a NULL pointer in bond_3ad_update_lacp_rate()
Also fix a minor bug, which could cause a port not to have
AD_STATE_LACP_TIMEOUT since there's no sync between
bond_3ad_update_lacp_rate() and bond_3ad_bind_slave(), by changing
the read_lock to a write_lock_bh in bond_3ad_update_lacp_rate().
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bastian Bittorf reported that some of the silent freezes on a Linksys WRT54G
were due to overflow of the RX DMA ring buffer, which was created with 64
slots. That finding reminded me that I was seeing similar crashed on a netbook,
which also has a relatively slow processor. After increasing the number of
slots to 128, runs on the netbook that previously failed now worked; however,
I found that 109 slots had been used in one test. For that reason, the number
of slots is being increased to 256.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Bastian Bittorf <bittorf@bluebottle.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Delete the MAC address of a VM, from the adapter's embedded switch,
after the VM had been migrated out of this adapter/server.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set gso_size to MSS obtained from adapter to avoid incorrect estimation
of receive MSS, which would lead to delayed ACKs in some traffic patterns
Example:
Send two or three packets and wait for ack and only then send
remaining packets.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Cleanly seperate 83xx Legacy interrupt handling code from 82xx
o Update 83xx Legacy interrupt handling code to match with the spec
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Config interrupt is not needed for mailbox interrupts.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added detailed error messages for FW CDRP command failure
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull in 'net' to take in the bug fixes that didn't make it into
3.8-final.
Also, deal with the semantic conflict of the change made to
net/ipv6/xfrm6_policy.c A missing rt6->n neighbour release
was added to 'net', but in 'net-next' we no longer cache the
neighbour entries in the ipv6 routes so that change is not
appropriate there.
Signed-off-by: David S. Miller <davem@davemloft.net>
When memory allocation using, kmalloc() fails, report appropriate error value.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an instance of DMA buffer on stack(being passed to
usb_control_msg) for the wireless USB version of the Agere Orinoco card driver.
It also fixes the missing audit for the return value of firmware download
routine. Found using smatch.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtlwifi allocates both setup_packet and data buffer of control message urb,
using shared kmalloc in _usbctrl_vendorreq_async_write. Structure used for
allocating is:
struct {
u8 data[254];
struct usb_ctrlrequest dr;
};
Because 'struct usb_ctrlrequest' is __packed, setup packet is unaligned and
DMA mapping of both 'data' and 'dr' confuses ARM/sunxi, leading to memory
corruptions and freezes.
Patch changes setup packet to be allocated separately.
[v2]:
- Use WARN_ON_ONCE instead of WARN_ON
Cc: <stable@vger.kernel.org>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For STA mode, collect VHT realated IEs from the Beacons or Probe
Responses and append similar VHT related IEs to association
requests.
For AP mode, get VHT related capability information and share it
with cfg80211 at the time of wiphy register. This information is
further used by cfg80211 and hostapd to start an AP with 802.11AC
support.
Currently only 8897 supports 802.11AC.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They all can make one line.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While unloading driver, we free all pending TX packets by flushing
TX ring. There is unhandled case for PCIE8897 while checking for
ring empty condition.
This patch adds the handling by calling mwifiex_pcie_txbd_empty().
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
John W. Linville says:
====================
This probably is the last big pull request for wireless bits
for 3.9. Of course, I'm sure there will be a few stragglers here
and there...surely a few bug fixes as well... :-) (In fact, I see
that Johannes has already queued-up a few more for me while I was
preparing this...)
Included are a number of pulls...
For mac80211-next, Johannes says:
"The biggest change I have is undoubtedly Marco's mesh powersave
implementation. Beyond that, I have a patch from Emmanuel to modify the
DTIM period API in mac80211, scan improvements and a removal of some
previous workaround code from Stanislaw, dynamic short slot time from
Thomas and 64-bit station byte counters from Vladimir. I also made a
number of changes myself, some related to WoWLAN, some auth/deauth
improvements and most of them BSS list cleanups."
"This time, I have relatively large number of fixes in various areas of
the code (a memory leak in regulatory, an RX race in mac80211, the new
radar checking caused a P2P device problem, some mesh issues with
stations, an older bug in tracing and for kernel-doc) as well as a
number of small new features. The biggest (in the diffstat) is my work
on hidden SSID tracking."
"Please pull to get
* radar detection work from Simon
* mesh improvements from Thomas
* a connection monitoring/powersave fix from Wojciech
* TDLS-related station management work from Jouni
* VLAN crypto fixes from Michael Braun
* CCK support in minstrel_ht from Felix
* an SMPS (not SMSP, oops) related improvement in mac80211 (Emmanuel)
* some WoWLAN work from Amitkumar Karwar: pattern match offset and a
documentation fix
* some WoWLAN work from myself (TCP connection wakeup feature API)
* and a lot of VHT (and some HT) work (also from myself)
And a number of more random cleanups/fixes. I merged mac80211/master to
avoid a merge problem there."
And regarding iwlwifi-next, Johannes says:
"We continue work on our new driver, but I also have a WoWLAN and AP mode
improvement for the previous driver and a change to use threaded
interrupts to prepare us for working with non-PCIe devices."
Regarding wl12xx, Luca says:
"A few more patches intended for 3.9. Mostly some clean-ups I've been
doing to make it easier to support device-tree. Also including one bug
fix for wl12xx where the rates we advertise were wrong and an update in
the wlconf structure to support newer firmwares."
For the nfc-next bits, Samuel says:
"This is the second NFC pull request for 3.9.
We have:
- A few pn533 fixes on top of Waldemar refactorization of the driver, one of
them fixes target mode.
- A new driver for Inside Secure microread chipset. It supports two
physical layers: i2c and MEI. The MEI one depends on a patchset that's
been sent to Greg Kroah-Hartman for inclusion into the 3.9 kernel [1]. The
dependency is a KConfig one which means this code is not buildable as long
as the MEI API is not usptream."
"This 3rd NFC pull request for 3.9 contains a fix for the microread MEI
physical layer support, as the MEI bus API changed.
From the MEI code, we now pass the MEI id back to the driver probe routine,
and we also pass a name and a MEI id table through the mei_bus_driver
structure. A few renames as well like e.g. mei_bus_driver to mei_driver or
mei_bus_client to mei_device in order to be closer to the driver model
practices."
For the ath6kl bits, Kalle says:
"There's not anything special here, most of the patches are just code
cleanup. The only functional changes are using the beacon interval from user
space and fixing a crash which happens when inserting and removing the
module in a loop."
Also, I pulled the wireless tree in order to resolve some pending
merge issues. On top of that, there is a bunch of work on brcmfmac
that leads up to P2P support. Also, mwifiex, rtlwifi, and a variety
of other drivers see some basic cleanups and minor enhancements.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
proc_net_remove is only used to remove proc entries
that under /proc/net,it's not a general function for
removing proc entries of netns. if we want to remove
some proc entries which under /proc/net/stat/, we still
need to call remove_proc_entry.
this patch use remove_proc_entry to replace proc_net_remove.
we can remove proc_net_remove after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Right now, some modules such as bonding use proc_create
to create proc entries under /proc/net/, and other modules
such as ipv4 use proc_net_fops_create.
It looks a little chaos.this patch changes all of
proc_net_fops_create to proc_create. we can remove
proc_net_fops_create after this patch.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPDMA interrupts are not properly acknowledged which leads to interrupt
storm, only cpdma interrupt 0 is acknowledged in Davinci CPDMA driver.
Changed cpdma_ctlr_eoi api to acknowledge 1 and 2 interrupts which are
used for rx and tx respectively.
Reported-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I removed a bit too much info last time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Theoretically, the card may not enter CTKILL:
In case the timer that iwl_prepare_ct_kill_task is setting,
will expire before tt->state revert to its previous state.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time event data structures are required also for P2P Device
interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FW can differentiate between scans, according to the interface
type on which the scan was issues. Supply the interfaces type
information to the FW.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Occasionally, we would run into this warning:
iwlwifi 0000:02:00.0: U iwl_mvm_protect_session extend 0x2601: only 200 ms left
iwlwifi 0000:02:00.0: U iwl_mvm_remove_time_event Removing TE 0x2601
iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command TIME_EVENT_CMD (#29), seq: 0x0925, 60 bytes at 37[5]:9
iwlwifi 0000:02:00.0: U iwl_pcie_send_hcmd_sync Attempting to send sync command TIME_EVENT_CMD
iwlwifi 0000:02:00.0: U iwl_pcie_send_hcmd_sync Setting HCMD_ACTIVE for command TIME_EVENT_CMD
iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command TIME_EVENT_CMD (#29), seq: 0x0926, 60 bytes at 38[6]:9
iwlwifi 0000:02:00.0: U iwl_mvm_time_event_response TIME_EVENT_CMD response - UID = 0x2601
iwlwifi 0000:02:00.0: I iwl_pcie_hcmd_complete Clearing HCMD_ACTIVE for command TIME_EVENT_CMD
iwlwifi 0000:02:00.0: U iwl_mvm_rx_time_event_notif Time event notification - UID = 0x2701 action 1
wlan0: associate with 00:0a:b8:55:a8:30 (try 2/3)
------------[ cut here ]------------
WARNING: at drivers/net/wireless/iwlwifi/mvm/time-event.c:269 iwl_mvm_time_event_send_add+0x163/0x1a0 [iwlmvm]()
Modules linked in: [...]
Call Trace:
[<c1046e42>] warn_slowpath_common+0x72/0xa0
[<c1046e92>] warn_slowpath_null+0x22/0x30
[<f8cad913>] iwl_mvm_time_event_send_add+0x163/0x1a0 [iwlmvm]
[<f8cadead>] iwl_mvm_protect_session+0xcd/0x1c0 [iwlmvm]
[<f8ca2087>] iwl_mvm_mac_mgd_prepare_tx+0x67/0xa0 [iwlmvm]
[<f882a130>] ieee80211_sta_work+0x8f0/0x1070 [mac80211]
The reason is a problem with asynchronous vs. synchronous
commands, what happens here is the following:
* TE 0x2601 is removed, the TIME_EVENT_CMD for that is async
* a new TE (will be 0x2701) is created, the TIME_EVENT_CMD
for that is sync and also uses a notification wait for the
response (to avoid another race condition)
* the response for the TE 0x2601 removal comes from the
firmware, and is handled by the notification wait handler
that's really waiting for the second response, but can't
tell the difference, we therefore see the message
"TIME_EVENT_CMD response - UID = 0x2601" instead of
"TIME_EVENT_CMD response - UID = 0x2701".
Fix this issue by making the TE removal synchronous as well,
this means that we wait for the response to that command
first, before there's any chance of sending a new one.
Also, to detect such issues more easily in the future, add
a warning to the notification handler that detects them.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is helpful for debugging the time event warning,
but also in general to see what's going on.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All station commands must include a valid MAC ID,
the ID 0 is randomly valid in some cases, but we
must set the ID properly. Do that by passing the
right station and using its mac_id_n_color.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the firmware to know when DTIM beacons arrive
we have to program the DTIM time in TSF and system
time in the MAC context. Since mac80211 now tracks
the different times (on demand), this becomes easy.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iwlwifi-next tree removed IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC
while the mac80211-next tree removed
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Upper case macros for various chip attributes are slightly
difficult to read and are a bit out of characterto the other
tg3_<foo> attribute functions.
Convert:
GET_ASIC_REV(tp->pci_chip_rev_id) -> tg3_asic_rev(tp)
GET_CHIP_REV(tp->pci_chip_rev_id) -> tg3_chip_rev(tp)
Remove:
GET_METAL_REV(tp->pci_chip_rev_id) -> tg3_metal_rev(tp) (unused)
Add:
tg3_chip_rev_id(tp) for tp->pci_chip_rev_id so access styles
are similar to tg3_asic_rev and tg3_chip_rev.
These macros are not converted to static inline functions
because gcc (tested with 4.7.2) is currently unable to
optimize the object code it produces the same way and code
is otherwise larger.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's the same value as tp->pci_chip_rev_id so use that
instead. This makes all CHIPREV_ID_<foo> tests the same.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this patch I get many unaligned access warnings per packet,
this patches fixes them all. This should improve performance on some
systems like mips.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to e1000, e1000e, igb, igbvf and ixgbe.
The e1000, e1000e, igb and igbvf are single patch changes and the
remaining 11 patches are all against ixgbe.
The e1000 patch is a comment cleanup to align e1000 with the code
commenting style for /drivers/net. It also contains a few other white
space cleanups (i.e. fix lines over 80 char, remove unnecessary blank
lines and fix the use of tabs/spaces).
The e1000e patch from Koki (Fujitsu) adds a warning when link speed is
downgraded due to SmartSpeed.
The igb patch from Stefan (Red Hat) increases the timeout in the ethtool
offline self-test because some i350 adapters would sometimes fail the
self-test because link auto negotiation may take longer than the current
4 second timeout.
The igbvf patch from Alex is meant to address several race issues that
become possible because next_to_watch could possibly be set to a value
that shows that the descriptor is done when it is not. In order to correct
that we instead make next_to_watch a pointer that is set to NULL during
cleanup, and set to the eop_desc after the descriptor rings have been written.
The remaining patches for ixgbe are a mix of fixes and added support as well
as some cleanup. Most notably is the added support for displaying the
number of Tx/Rx channels via ethtool by Alex. Also Aurélien adds the
ability for reading data from SFP+ modules over i2c for diagnostic
monitoring.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In ehea.h the minimal entries is 2^7 - 1:
#define EHEA_MIN_ENTRIES_QP 127
Thus change the module param description accordinglly
Signed-off-by: Dave Young <dyoung@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes have made it so that MAX_SKB_FRAGS is now never less than 16.
As a result we were seeing issues on systems with 64K pages as it would
cause DESC_NEEDED to increase to 68, and we would need over 136 descriptors
free before clean_tx_irq would wake the queue.
This patch makes it so that DESC_NEEDED is always MAX_SKB_FRAGS + 4. This
should prevent any possible deadlocks on the systems with 64K pages as we will
now only require 42 descriptors to wake.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that TXDCTL.WTHRESH is set to 1 when BQL is enabled
and EITR is set to more than 100k interrupts per second to avoid Tx timeouts.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for reading data from SFP+ modules over i2c.
Signed-off-by: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch replaces instances where a return code from i2c operations
were checked against a list of error codes with a much simpler
if ( status != 0 ) check.
Some whitespace cleanups included.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes sure that the SW lock is released after all i2c
operations complete in the retry code path.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for the ethtool set_channels operation.
Since the ixgbe driver has to support DCB as well as the other modes the
assumption I made here is that the number of channels in DCB modes refers
to the number of queues per traffic class, not the number of queues total.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for the ethtool get_channels operation.
Since the ixgbe driver has to support DCB as well as the other modes the
assumption I made here is that the number of channels in DCB modes refers
to the number of queues per traffic class, not the number of queues total.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ixgbe_setup_tc code is essentially the same code we need any time we have
to update the number of queues. As such I am making it available always and
just stripping the DCB specific bits out when DCB is disabled instead of
stripping the entire function.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change updates the ixgbe driver to use __netdev_pick_tx instead of
the current logic it is using to select a queue. The main result of this
change is that ixgbe can now fully support XPS, and in the case of non-FCoE
enabled configs it means we don't need to have our own ndo_select_queue.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds support for ixgbe to configure the XPS queue mapping on
load. The result of this change is that on open we will now be resetting
the number of Tx queues, and then setting the default configuration for XPS
based on if ATR is enabled or disabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Reviewed-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of adjusting the FCoE and Flow director limits based on the number
of CPUs we can define them much sooner. This allows the user to come
through later and adjust them once we have updated the code to support the
set_channels ethtool operation.
I am still allowing for FCoE and RSS queues to be separated if the number
queues is less than the number of CPUs. This essentially treats the two
groupings like they are two separate traffic classes.
In addition I am changing the initialization to use the MAX_TX/RX_QUEUES
defines instead of trying to compute the value as it will be possible in
upcoming patches for the user to request the maximum number of queues.
I have also updated things so that the upper limit on queues is exactly 63
instead of allowing it to go up to 64. The reason for this change is to
address the fact thqt the driver only supports up to 63 queue vectors since
the hardware supports 64 MSI-X vectors, but one must be reserved for "other"
causes.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On several machines with i350 adapters the ethtool offline self-test sometimes
fails. This happens because link auto negotiation may take longer than the
timeout of 4 seconds. Increasing the timeout by 1 seconds resolves the issue.
Output from a failing i350 offline self-test:
while [ 1 ]; do ethtool -t eth2 offline; done
The test result is PASS
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 0
The test result is FAIL
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 1
The test result is PASS
The test extra info:
Register test (offline) 0
Eeprom test (offline) 0
Interrupt test (offline) 0
Loopback test (offline) 0
Link test (on/offline) 0
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to address several race issues that become possible
because next_to_watch could possibly be set to a value that shows that the
descriptor is done when it is not. In order to correct that we instead make
next_to_watch a pointer that is set to NULL during cleanup, and set to the
eop_desc after the descriptor rings have been written.
To enforce proper ordering the next_to_watch pointer is not set until after
a wmb writing the values to the last descriptor in a transmit. In order to
guarantee that the descriptor is not read until after the eop_desc we use the
read_barrier_depends which is only really necessary on the alpha architecture.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current e1000e driver doesn't tell nothing when Link Speed is downgraded due to
SmartSpeed. As a result, users suspect that there is something wrong with
NIC. If the cause of it is SmartSpeed, there is no means to replace NIC. This
patch make e1000e notify users that SmartSpeed worked.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixes whitespace issues, such as lines exceeding 80 chars, needless blank
lines and the use of spaces where tabs are needed. In addition, fix
multi-line comments to align with the networking standard.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
There is no need to implement empty suspend/resume callbacks if there is nothing
to do during suspend/resume. The drivers will behave the same with no callbacks
or empty callbacks during suspend/resume.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This pacth fixes the parsing of the eee_timer driver parameter.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to igb and ixgbe. Most of the changes
are against igb, except for one patch against ixgbe.
There are 3 igb fixes from Carolyn which were reported by Dan
Carpenter which resolve issues found in the get_i2c_client(). Alex
does some cleanup of the igb driver to match similar functionality
in ixgbe on transmit. Alex also makes it so that we can enable the use
of build_skb for cases where jumbo frames are disabled. The advantage
to this is that we do not have to perform a memcpy to populate the header
and as a result we see a significant performance improvement.
Akeem provides 4 patches to initialize function pointers and do a
re-factoring of the function pointers in igb_get_variants() to assist
with driver debugging.
The ixgbe patch comes from Emil to reshuffle the switch/case structure
of the flag assignment to allow for the flags to be set for each MAC
type separately. This is needed for new hardware that does not have feature
parity with older hardware.
v2: updated patches 4 & 5 based on feedback from Ben Hutchings and Eric
Dumazet
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This function will be used in next GRE_GSO patch. This patch does
not change any functionality.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Before the device is opened, the carrier state should be off. It
will not race with the link interrupt if we set it before calling
register_netdev().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't set the default size to 128K if it is 5762. Instead, rely on the
size we obtain from NVRAM location 0xf0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This chip supports Energy Efficient Ethernet. The existing code only
supports a smaller set of devices with 5718 PCI ID. Expand support for
all devices with the same 5717 B0 chip ID.
Signed-off-by: Michael Chan <mchan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch also adds a couple of fixes
- For the 57766 and non Ax versions of 57765, bootcode needs to setup
the PCIE Fast Training Sequence (FTS) value to prevent transmit hangs.
Unfortunately, it does not have enough room in the selfboot case (i.e.
devices with no NVRAM). The driver needs to implement this.
- For performance reasons, the 2k DMA engine mode on the 57766 should
be enabled and dma size limited to 2k for standard sized packets.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRAuO3AAoJEHm+PkMAQRiGbfAH/1C3QQKB11aBpYLAw7qijAze
yOui26UCnwRryxsO8zBCQjGoByy5DvY/Q0zyUCWUE6nf/JFSoKGUHzfJ1ATyzGll
3vENP6Fnmq0Hgc4t8/gXtXrZ1k/c43cYA2XEhDnEsJlFNmNj2wCQQj9njTNn2cl1
k6XhZ9U1V2hGYpLL5bmsZiLVI6dIpkCVw8d4GZ8BKxSLUacVKMS7ml2kZqxBTMgt
AF6T2SPagBBxxNq8q87x4b7vyHYchZmk+9tAV8UMs1ecimasLK8vrRAJvkXXaH1t
xgtR0sfIp5raEjoFYswCK+cf5NEusLZDKOEvoABFfEgL4/RKFZ8w7MMsmG8m0rk=
=m68Y
-----END PGP SIGNATURE-----
Merge branch 'omap/multiplatform-fixes', tag 'v3.8-rc5' into next/multiplatform
The omap multiplatform support uncovered a bug in the cwdavinci_cpdma
code and was missing two drivers that are enabled now but are not
quite ready for multiplatform, as found by allyesconfig builds.
There is also a conflict generated by automated merge in
arch/arm/mach-omap2/drm.c between a bug fix that went into v3.8-rc5
and a different version of the same fix that went into the
omap/multiplatform branch. This merge removes the extraneous
#include that was causing build errors.
* omap/multiplatform-fixes:
net: cwdavinci_cpdma: export symbols for cpsw
remoteproc: omap: depend on OMAP_MBOX_FWK
[media] davinci: do not include mach/hardware.h
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With the support for ARM AM33xx in multiplatform kernels
in 3.9, an older bug appears in ARM allmodconfig:
When the cpsw driver is built as a module with cpdma
support enabled, it uses symbols that the cpdma driver
does not export.
Without this patch, building allmodconfig results in:
ERROR: "cpdma_ctlr_int_ctrl" [drivers/net/ethernet/ti/ti_cpsw.ko] undefined!
ERROR: "cpdma_control_set" [drivers/net/ethernet/ti/ti_cpsw.ko] undefined!
ERROR: "cpdma_ctlr_eoi" [drivers/net/ethernet/ti/ti_cpsw.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: netdev@vger.kernel.org
This patch reshuffles the switch/case structure of the flag assignment to
allow for the flags to be set for each MAC type separately. This is needed
for new HW that does not have feature parity with older HW.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch simplifies igb_get_invariants function by moving all implemented
function pointers in this function to individual separate functions,
based on their functionalities, this would make debugging much easier.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch initializes MAC function pointers for device configuration.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch initializes NVM function pointers for device configuration.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch initializes PHY function pointers for device configuration.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After reviewing the igb and ixgbe code I realized there are a few issues in
how the code is structured. Specifically we are not checking the size of the
buffers being used in transmits and we are not using the same value to
determine when to stop or start a Tx queue. As such the code is prone to be
buggy.
This patch makes it so that we have one value DESC_NEEDED that we will use for
starting and stopping the queue. In addition we will check the size of
buffers being used when setting up a transmit so as to avoid a possible buffer
overrun if we were to receive a frame with a block of data larger than 32K in
skb->data.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch correctly resolves the sparse warnings found with this
function.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the allocation function in igb_get_i2c_client to use
GFP_ATOMIC instead of GFP_KERNEL because we have a spinlock.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes an issue where we check for irq's disabled then exit after
explicitly disabling them with spin_lock_irqsave.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <arron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change makes it so that we can enable the use of build_skb for cases
where jumbo frames are disabled. The advantage to this is that we do not
have to perform a memcpy to populate the header and as a result we see a
significant performance improvement.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Otherwise memory corruption occurs when using channel contexts (ATM when
param 'channel' > 1).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of modifying the HT SMPS capability field
for stations, track the SMPS mode explicitly in a
new field in the station struct and use it in the
drivers that care about it. This simplifies the
code using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.
To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.
If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.
Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.
While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the casts of the first argument of memset.
Neaten the style by using the sizeof the actual variable
being memset not the sizeof the type of variable.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These messages don't seem to be errors but notifications
that some attribute isn't quite right.
Don't mark them as errors.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch check output of pci_map_single() calls. I missed them on
my previous patch "iwlegacy: check for dma mapping errors", which
fixed only pci_map_page() calls.
To handle remaining possible dma mappings errors, we need to rearrange
ilXXXX_tx_skb() and il_enqueue_hcmd() functions.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check output of dma_map_single functions which nowadays can fail (when
IOMMU is used). On write_beacon callbacks just print error, similar
like padding error is handled by rt2800_write_beacon.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for handling of PCIe sleep cookie depending
upon device properties. Some PCIe devices need sleep cookie probing
before accessing HW while some others don't. A new sleep_cookie
variable is defined as part of mwifiex_pcie_card_reg strcture and
set/reset as per device capability.
Sleep cookie is allocated/accessed/freed only when flag sleep_cookie
for this particular device is enabled.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the number of drivers in the rtlwifi family has grown, the Kconfig
section for them has grown unwieldy. This change has two effects: (1)
Variable RTLWIFI_DEBUG is documented, and (2) the entries for the
drivers that depend on RTLWIFI are indented.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ccode is not NUL terminated. Presumably insisting on a terminator makes
brcms_c_country_valid() return false when it's not intended. ccode[2]
is sprom->leddc_on_time.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a less obvious error on one hand, and prevents futher
similar errors by disambiguating and optimizing RxFCB indication,
on the other hand.
The error consists in NETIF_F_HW_VLAN_TX flag being used as an
indication of Rx FCB insertion. This happened as soon gfar_uses_fcb(),
which despite its name indicates Rx FCB insertion, started
incorporating is_vlan_on().
is_vlan_on(), on the other hand, is also a misleading construct because
we need to differentiate b/w hw VLAN extraction/VLEX (marked by VLAN_RX
flag) and hw VLAN insertion/VLINS (VLAN_TX flag), which are different
mechanisms using different types of FCBs.
The hw spec for the RxFCB feature is as follows:
In the case of RxBD rings, FCBs (Frame Control Block) are inserted by
the eTSEC whenever RCTRL[PRSDEP] is set to a non-zero value. Only one
FCB is inserted per frame (in the buffer pointed to by the RxBD with
bit F set). TOE acceleration for receive is enabled for all rx frames
in this case.
This patch introduces priv->uses_rxfcb field to quickly signal RxFCB
insertion in accordance with the specification above.
The dependency on FSL_GIANFAR_DEV_HAS_TIMER was also eliminated as
another source of confusion. The actual dependency is to priv->hwts_rx_en.
Upon changing priv->hwts_rx_en via IOCTL, the gfar device is being
restarted and on init_mac() the priv->hwts_rx_en flag determines RxFCB
insertion, and rctrl is programmed accordingly. The patch takes care
of this case too.
Though maybe not as self documenting as the inlining version uses_fcb(),
priv->uses_rxfcb has the main purpose to quickly signal, on the hot path,
that the incoming frame has a *Rx* FCB block inserted which needs to be
pulled out before passing the skb to the stack. This is a performance
critical operation, it needs to happen fast, that's why uses_rxfcb is
placed in the first cacheline of gfar_private.
This is also why a cached rctrl cannot be used instead: 1) because
we don't have 32 bits available in the first cacheline of gfar_priv
(but only 16); 2) bit operations are expensive on the hot path.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The controller's ref manual states clearly that when the hw Rx vlan
offload feature is enabled, meaning that the VLEX bit from RCTRL is
correctly enabled, then the hw performs automatic VLAN tag extraction
and deletion from the ethernet frames. So there's no point in trying to
increase the rx buff size when rxvlan is on, as the frame is actually
smaller.
And the Tx vlan hw accel feature (VLINS) has nothing to do with rx buff
size computation.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No return code is expected from gfar_process_frame(), hence
change it to return void.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Group run-time critical fields within the 1st cacheline (32B)
followed by the tx|rx_queue reference arrays and the interrupt
group instances (gfargrp), all cacheline aligned.
This has several benefits. Firstly comes the performance benefit
by having the members required by the driver's hot path re-grouped
in the structure's first cache lines, whereas the unimportant
members were pushed towards the end of the struct.
Another benefit comes from eliminating a 24 byte memory hole that
was rendering gfar_priv's 2nd cacheline useless. The default gcc
layout of gfar_private leaves an implicit 24 byte hole after the
errata (enum) member. This patch fixes it.
The uchar bitfields were pushed towards the end of the struct
as these are not run-time performance critical (used for init
time operations). Because there is no other 2 byte member
around to couple the uchar bitfields memeber with, we will
have an addititnal 2 byte hole after the bitfields. This is
unsignificant however, and it doesn't influence gfar_priv's
size, because the whole structure is padded to be a 32B multiple.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use device pointer (dev) to simplify the code and to
avoid double indirections, especially on the hot path.
Basically, instead of accessing priv to get the ofdev
reference and then accessing the ofdev structure to
dereference the needed dev pointer, we will get the
dev pointer directly from priv.
The dev pointer is required on the hot path, see gfar_new_rxbdp
or gfar_clean_rx_ring (or xmit), and this patch makes
it available directly from priv's 1st cacheline.
This change is reflected at asm level too, taking (the hot)
gfar_new_rxbdp():
initial version -
18c0: 7c 7e 1b 78 mr r30,r3
18d0: 81 69 04 3c lwz r11,1084(r9)
18d8: 34 6b 00 10 addic. r3,r11,16
18dc: 41 82 00 08 beq- 18e4
patched version -
18d0: 80 69 04 38 lwz r3,1080(r9)
18d8: 2f 83 00 00 cmpwi cr7,r3,0
18dc: 41 9e 00 08 beq- cr7,18e4
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
