Commit Graph

11793 Commits

Author SHA1 Message Date
Rafael J. Wysocki
98feb7cc61 Merge branch 'acpi-cleanup'
* acpi-cleanup: (22 commits)
  ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment.
  ACPI / tables: Check if id is NULL in acpi_table_parse()
  ACPI / proc: Include appropriate header file in proc.c
  ACPI / EC: Remove unused functions and add prototype declaration in internal.h
  ACPI / dock: Include appropriate header file in dock.c
  ACPI / PCI: Include appropriate header file in pci_link.c
  ACPI / PCI: Include appropriate header file in pci_slot.c
  ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c
  ACPI / NVS: Include appropriate header file in nvs.c
  ACPI / OSL: Mark the function acpi_table_checksum() as static
  ACPI / processor: initialize a variable to silence compiler warning
  ACPI / processor: use ACPI_COMPANION() to get ACPI device
  ACPI: correct minor typos
  ACPI / sleep: Drop redundant acpi_disabled check
  ACPI / dock: Drop redundant acpi_disabled check
  ACPI / table: Replace '1' with specific error return values
  ACPI: remove trailing whitespace
  ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module
  ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h>
  SFI / ACPI: Fix warnings reported during builds with W=1
  ...

Conflicts:
	drivers/acpi/nvs.c
	drivers/hwmon/asus_atk0110.c
2014-01-12 23:44:09 +01:00
Boris BREZILLON
fb5f1834c3 usb: ohci-at91: fix irq and iomem resource retrieval
When using dt resources retrieval (interrupts and reg properties) there is
no predefined order for these resources in the platform dev resources
table.

Retrieve resources using platform_get_resource and platform_get_irq
functions instead of direct resource table entries to avoid resource type
mismatch.

Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-17 13:22:36 -08:00
Felipe Balbi
7cd0c298f6 usb: phy: fix driver dependencies
both isp1301-omap and fsl_usb2_otg drivers
depend on usb_bus_start_enum() which is only
defined if CONFIG_USB != n. There is a problem,
however, where both those drivers could be
statically linked, while CONFIG_USB=m.

Fix the problem by fixing driver dependency.

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-16 21:31:24 -08:00
Takashi Iwai
6962d914f3 xhci: Limit the spurious wakeup fix only to HP machines
We've got regression reports that my previous fix for spurious wakeups
after S5 on HP Haswell machines leads to the automatic reboot at
shutdown on some machines.  It turned out that the fix for one side
triggers another BIOS bug in other side.  So, it's exclusive.

Since the original S5 wakeups have been confirmed only on HP machines,
it'd be safer to apply it only to limited machines.  As a wild guess,
limiting to machines with HP PCI SSID should suffice.

This patch should be backported to kernels as old as 3.12, that
contain the commit 638298dc66 "xhci: Fix
spurious wakeups after S5 on Haswell".

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=66171
Cc: stable@vger.kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: <dashing.meng@gmail.com>
Reported-by: Niklas Schnelle <niklas@komani.de>
Reported-by: Giorgos <ganastasiouGR@gmail.com>
Reported-by: <art1@vhex.net>
2013-12-10 11:44:39 -08:00
Peter Chen
5a1e1456fc usb: chipidea: fix nobody cared IRQ when booting with host role
If we connect Male-A-To-Male-A cable between otg-host and host pc,
the ci->vbus_active is set wrongly, and cause the controller run
at peripheral mode when we load gadget module (ci_udc_start will be run),
but the software runs at host mode due to id = 0. The ehci_irq
can't handle suspend (USBi_SLI) interrupt which is enabled for
peripheral mode, it causes no one will handle irq error.

This patch is needed for 3.12 stable

Cc: stable <stable@vger.kernel.org>
Acked-by: Michael Grzeschik <mgr@pengutronix.de>
Reported-by: Marc Kleine-Budde <mkl@pengutronix.de>
Tested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-09 13:14:12 -08:00
Fabio Estevam
cc5c9eb67f usb: chipidea: host: Only disable the vbus regulator if it is not NULL
Commit 40ed51a4b (usb: chipidea: host: add vbus regulator
control) introduced a smatch complaint because regulator_disable() is called
without checking whether ci->platdata->reg_vbus is not NULL.

Fix this by adding the check.

This patch is needed for 3.12 stable

Cc: stable <stable@vger.kernel.org>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-09 13:14:12 -08:00
Dmitry Kunilov
52d0dc7597 usb: serial: zte_ev: move support for ZTE AC2726 from zte_ev back to option
ZTE AC2726 EVDO modem drops ppp connection every minute when driven by
zte_ev but works fine when driven by option. Move the support for AC2726
back to option driver.

Signed-off-by: Dmitry Kunilov <dmitry.kunilov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-09 13:14:12 -08:00
Bjørn Mork
4144bc861e usb: cdc-wdm: manage_power should always set needs_remote_wakeup
Cc: stable <stable@vger.kernel.org>
Reported-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-09 13:14:11 -08:00
Greg Kroah-Hartman
757de81e8b usb: fixes for v3.13-rc4
DWC3 learned that it can't resume a PHY which wasn't
 initialized and it also learned to not leave PHY powered
 up in case of an error.
 
 twl6030-usb PHY driver got a fix for a signedness bug in
 twl6030_readb().
 
 Tegra PHY driver got a bug fix where it could return success
 even though there was an error.
 
 Signed-of-by: Felipe Balbi <balbi@ti.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.15 (GNU/Linux)
 
 iQIcBAABAgAGBQJSphkAAAoJEIaOsuA1yqRE7tUP/0NjOJBbirUH8adlyxLXGCZK
 9ASyH6irzuQz5QDqB3tSMstPTwUQ353ZIGI/xX6pHIEsOzUjKMzUDC0Hs81dZkgR
 SGNDOlttpiD4WiV3XpYRH5gYj+50ustgd4K+CmwS3255tVBxXTIVU2qvAp4+hu1T
 4lBhNy/vlmuO4Lal3lT1xAQojH0KyX7tnOHByoPSsdZ6NXTR8+Ytui58vCzrFgwW
 rUIBsl7WGZjI2gyM3Zxw9KgD5oVTyxmq2KPBgE9V13dZ0OdwOYWScws0cfDAiWJ8
 Yrg3d0o+JEFIjf3kYJEbsCjyyv4nWtFLOIgS58i3yHS1SZ9a+PvwOAaCulZY9pVq
 42Jp8nzXV1jgsARgjIVO65yxg3ZedybvXDpNQQ7j2AamaYoGHLohYxhHn6d0rLCM
 8VkIyG1xtC1llf8gl8xkTbAMDs410be5IfOfi1CrbbZHWR2gnsuq8iin+1eUCg31
 0OWmMKMk9S+qD69oNcujV8vj86QbUslS/+2KnpZNT7S+FGLSVjkGEHrbSftTTbcV
 G/kL/rovisYTB0dqV6jeYjTTSXrGJ+FEaFKBnNonWY5Mh+TLL3MMrz13lsHB62cQ
 QO8Al3d8OP6PFDKJUljxq8vCwZ0t2LhrZPUJoqEycdbMZ4465AQzv/IG0k7q6Wc6
 vNkK5aE47ocYVpeuKknz
 =MfzU
 -----END PGP SIGNATURE-----

Merge tag 'fixes-for-v3.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v3.13-rc4

DWC3 learned that it can't resume a PHY which wasn't
initialized and it also learned to not leave PHY powered
up in case of an error.

twl6030-usb PHY driver got a fix for a signedness bug in
twl6030_readb().

Tegra PHY driver got a bug fix where it could return success
even though there was an error.

Signed-of-by: Felipe Balbi <balbi@ti.com>
2013-12-09 12:58:19 -08:00
Lv Zheng
8b48463f89 ACPI: Clean up inclusions of ACPI header files
Replace direct inclusions of <acpi/acpi.h>, <acpi/acpi_bus.h> and
<acpi/acpi_drivers.h>, which are incorrect, with <linux/acpi.h>
inclusions and remove some inclusions of those files that aren't
necessary.

First of all, <acpi/acpi.h>, <acpi/acpi_bus.h> and <acpi/acpi_drivers.h>
should not be included directly from any files that are built for
CONFIG_ACPI unset, because that generally leads to build warnings about
undefined symbols in !CONFIG_ACPI builds.  For CONFIG_ACPI set,
<linux/acpi.h> includes those files and for CONFIG_ACPI unset it
provides stub ACPI symbols to be used in that case.

Second, there are ordering dependencies between those files that always
have to be met.  Namely, it is required that <acpi/acpi_bus.h> be included
prior to <acpi/acpi_drivers.h> so that the acpi_pci_root declarations the
latter depends on are always there.  And <acpi/acpi.h> which provides
basic ACPICA type declarations should always be included prior to any other
ACPI headers in CONFIG_ACPI builds.  That also is taken care of including
<linux/acpi.h> as appropriate.

Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (drivers/pci stuff)
Acked-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> (Xen stuff)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2013-12-07 01:03:14 +01:00
Chris Ruehl
851dd02b4f usb: phy-tegra-usb.c: wrong pointer check for remap UTMI
usb: phy-tegra-usb.c: wrong pointer check for remap UTMI

A wrong pointer was used to test the result of devm_ioremap()

Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Acked-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-12-06 14:32:15 -06:00
Julius Werner
2d51f3cd11 usb: hub: Use correct reset for wedged USB3 devices that are NOTATTACHED
This patch adds a check for USB_STATE_NOTATTACHED to the
hub_port_warm_reset_required() workaround for ports that end up in
Compliance Mode in hub_events() when trying to decide which reset
function to use. Trying to call usb_reset_device() with a NOTATTACHED
device will just fail and leave the port broken.

Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04 17:00:43 -08:00
Daniel Mack
9876388edf usb: ohci-pxa27x: include linux/dma-mapping.h
Include linux/dma-mapping.h to make the new functions available that are
used since 22d9d8e83 ("DMA-API: usb: use dma_set_coherent_mask()").

drivers/usb/host/ohci-pxa27x.c: In function ‘ohci_pxa_of_init’:
drivers/usb/host/ohci-pxa27x.c:310:2: error: implicit declaration of function ‘dma_coerce_mask_and_coherent’ [-Werror=implicit-function-declaration]
drivers/usb/host/ohci-pxa27x.c:310:2: error: implicit declaration of function ‘DMA_BIT_MASK’ [-Werror=implicit-function-declaration]

Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04 16:57:46 -08:00
David Cluytens
3b59d16c51 USB: cdc-acm: Added support for the Lenovo RD02-D400 USB Modem
Signed-off-by: David Cluytens <david.cluytens@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-04 16:53:03 -08:00
Colin Leitner
a313249937 USB: pl2303: fixed handling of CS5 setting
This patch fixes the CS5 setting on the PL2303 USB-to-serial devices. CS5 has a
value of 0 and the CSIZE setting has been skipped altogether by the enclosing
if. Tested on 3.11.6 and the scope shows the correct output after the fix has
been applied.

Tagged to be added to stable, because it fixes a user visible driver bug and is
simple enough to backport easily.

Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-02 21:52:57 -08:00
Colin Leitner
8704211f65 USB: ftdi_sio: fixed handling of unsupported CSIZE setting
FTDI UARTs support only 7 or 8 data bits. Until now the ftdi_sio driver would
only report this limitation for CS6 to dmesg and fail to reflect this fact to
tcgetattr.

This patch reverts the unsupported CSIZE setting and reports the fact with less
severance to dmesg for both CS5 and CS6.

To test the patch it's sufficient to call

    stty -F /dev/ttyUSB0 cs5

which will succeed without the patch and report an error with the patch
applied.

As an additional fix this patch ensures that the control request will always
include a data bit size.

Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-02 21:52:57 -08:00
Colin Leitner
78692cc338 USB: mos7840: correct handling of CS5 setting
This patch removes an erroneous check of CSIZE, which made it impossible to set
CS5.

Compiles clean, but couldn't test against hardware.

Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-02 21:52:57 -08:00
Colin Leitner
711fbdfbf2 USB: spcp8x5: correct handling of CS5 setting
This patch removes an erroneous check of CSIZE, which made it impossible to set
CS5.

Compiles clean, but couldn't test against hardware.

Signed-off-by: Colin Leitner <colin.leitner@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-02 21:52:57 -08:00
Thomas Pugliese
471e42ad14 usb: wusbcore: fix deadlock in wusbhc_gtk_rekey
When multiple wireless USB devices are connected and one of the devices
disconnects, the host will distribute a new group key to the remaining
devicese using wusbhc_gtk_rekey.  wusbhc_gtk_rekey takes the
wusbhc->mutex and holds it while it submits a URB to set the new key.
This causes a deadlock in wa_urb_enqueue when it calls a device lookup
helper function that takes the same lock.

This patch changes wusbhc_gtk_rekey to submit a work item to set the GTK
so that the URB is submitted without holding wusbhc->mutex.

Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-02 15:21:04 -08:00
Thomas Pugliese
6161ae5f1f usb: wusbcore: do device lookup while holding the hc mutex
This patch modifies the device notification handler to not look up the
wusb_dev object before it calls the lower-level handler routines since
the wusbhc mutex is not held when calling those routines and the device
could go away in the meantime.  Instead, let the individual notification
handlers get the device ptr if they need to after they have taken the
mutex.

Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-02 15:21:04 -08:00
Thomas Pugliese
f4042c068a usb: wusbcore: send keepalives to unauthenticated devices
This patch modifies the WUSB device disconnect timer code to send
keepalives to all connected devices even if they are not authenticated.
This fixes a problem where unauthenticated devices that lose their
connection before they are authenticated will stay in the device tree
forever.  More importantly, devices in this situation will never
relinquish their port on the root hub so eventually all root ports will
be taken up and no other devices can connect.

A comment in the existing code states that there are some devices that
may not respond to keepalives if they have not been authenticated.  That
comment is about 5 years old and I don't know of any WUSB devices that
act that way.  Either way, any buggy devices that may still be around
will continue to work as long as they can transition to the
authenticated state within the WUSB LOA timeout of 4s, which is not
unreasonable to expect.

Signed-off-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-02 15:21:03 -08:00
Fangxiaozhi (Franko)
2bf308d7bc USB: option: support new huawei devices
Add new supporting declarations to option.c, to support Huawei new
devices with new bInterfaceProtocol value.

Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-02 13:51:02 -08:00
Gustavo Zacarias
8f173e22ab USB: serial: option: blacklist interface 1 for Huawei E173s-6
Interface 1 on this device isn't for option to bind to otherwise an oops
on usb_wwan with log flooding will happen when accessing the port:

tty_release: ttyUSB1: read/write wait queue active!

It doesn't seem to respond to QMI if it's added to qmi_wwan so don't add
it there - it's likely used by the card reader.

Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-12-02 13:50:54 -08:00
David Laight
35773dac5f usb: xhci: Link TRB must not occur within a USB payload burst
Section 4.11.7.1 of rev 1.0 of the xhci specification states that a link TRB
can only occur at a boundary between underlying USB frames (512 bytes for
high speed devices).

If this isn't done the USB frames aren't formatted correctly and, for example,
the USB3 ethernet ax88179_178a card will stop sending (while still receiving)
when running a netperf tcp transmit test with (say) and 8k buffer.

This should be a candidate for stable, the ax88179_178a driver defaults to
gso and tso enabled so it passes a lot of fragmented skb to the USB stack.

Notes from Sarah:

Discussion: http://marc.info/?l=linux-usb&m=138384509604981&w=2

This patch fixes a long-standing xHCI driver bug that was revealed by a
change in 3.12 in the usb-net driver.  Commit
638c5115a7 "USBNET: support DMA SG" added
support to use bulk endpoint scatter-gather (urb->sg).  Only the USB
ethernet drivers trigger this bug, because the mass storage driver sends
sg list entries in page-sized chunks.

This patch only fixes the issue for bulk endpoint scatter-gather.  The
problem will still occur for periodic endpoints, because hosts will
interpret no-op transfers as a request to skip a service interval, which
is not what we want.

Luckily, the USB core isn't set up for scatter-gather on isochronous
endpoints, and no USB drivers use scatter-gather for interrupt
endpoints.  Document this known limitation so that developers won't try
to use urb->sg for interrupt endpoints until this issue is fixed.  The
more comprehensive fix would be to allow link TRBs in the middle of the
endpoint ring and revert this patch, but that fix would touch too much
code to be allowed in for stable.

This patch should be backported to kernels as old as 3.12, that contain
the commit 638c5115a7 "USBNET: support DMA
SG".  Without this patch, the USB network device gets wedged, and stops
sending packets.  Mark Lord confirms this patch fixes the regression:

http://marc.info/?l=linux-netdev&m=138487107625966&w=2

Signed-off-by: David Laight <david.laight@aculab.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Mark Lord <mlord@pobox.com>
Cc: stable@vger.kernel.org
2013-12-02 11:57:10 -08:00
Greg Kroah-Hartman
c24cb6c8b5 usb: fixes for v3.13-rc2
First set of fixes for this -rc cycle. A few important
 fixes which should be backported to stable kernels and
 the usual set of sparse warning fixes. There's also a
 regression fix on phy-generic.c which would prevent
 am335x-based platforms from having their PHY drivers
 probed.
 
 Signed-of-by: Felipe Balbi <balbi@ti.com>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1.4.15 (GNU/Linux)
 
 iQIcBAABAgAGBQJSk5HFAAoJEIaOsuA1yqRE7xoP/Rz2ZMt1BlRH3rHorQL+0mqs
 2KDN7Vz+vLlt4BldLYiMpKTe7zTmV28yR+MaTHzX1RVJEXJl0/hJVPvOmOdAPAkX
 Y5KnjWrUNhrG6ChxUwaJslWLA8ACnV5PwdQDsSJYGKAi0jWuXE0qSJoGqX8PgJX/
 gU9TK5iWHFflmkpg8M8UPx2XyMFHYfonJ6Nh2A8bYTkHqHFZp/CoCZKQqmAathKg
 9Kyze3elKyA5Ch1JXf++WIViCXMkNRgWp4YNYUDj9t32mw2iLyg0czMvTNK0OqeR
 ICqzz4EgiSQjFq4p70kJSDXqRUGIre/JcZk7Gq3zAAUw0ScuJRQOZBmDiyu5K2vk
 UG+H05YZCFXqr4e+80WoIzLyaZzokOA/RI9sDPKeF3NvaxCCtf9BsEu4ugOwoBrz
 9MQhHJBcvJAYbBeUy/L80btL7SoSc76mQ08+HImeDoolZMFgVcS0bUTPE0VSwW9U
 oDnOAe/kSCRSZPEkDp6nbKqp3OX1tvWA+1bsYslsEbPotnulYWawd4OCPhPWKc2J
 Uu6HBC6aDZ6DS3YH/GKkJONV3oRjaqjDwHMoTlZa3bDftPACzGgXc+r8s4iiLzya
 VHK5R8JK32hD/GI/5oWhJVgDQmFbp2Kk6MeSTT1AgiJ75x7Z1dWncePohdaPrMt/
 Wn19N0Ype+72HhTZ3oP2
 =ZzE5
 -----END PGP SIGNATURE-----

Merge tag 'fixes-for-v3.13-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

usb: fixes for v3.13-rc2

First set of fixes for this -rc cycle. A few important
fixes which should be backported to stable kernels and
the usual set of sparse warning fixes. There's also a
regression fix on phy-generic.c which would prevent
am335x-based platforms from having their PHY drivers
probed.

Signed-of-by: Felipe Balbi <balbi@ti.com>
2013-11-27 09:49:03 -08:00
Dan Carpenter
0b55149033 usb: phy: twl6030-usb: signedness bug in twl6030_readb()
"ret" needs to be signed for the error handling to work.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 15:53:43 -06:00
Kishon Vijay Abraham I
501fae5125 usb: dwc3: power off usb phy in error path
usb phy was power'ed on but was never power'ed off in the error path.
Fix it.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 15:15:52 -06:00
Kishon Vijay Abraham I
3088f1085d usb: dwc3: invoke phy_resume after phy_init
usb_phy_set_suspend(phy, 0) is called before usb_phy_init. Fix it.

Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 15:15:50 -06:00
George Cherian
2cf93bea3d usb: gadget: f_mass_storage: call try_to_freeze only when its safe
Call try_to_freeze() in sleep_thread() only when it's safe to sleep.
do_read() and do_write() calls sleep_thread with lock held.
Make sure these won't call try_to_freeze() by passing can_freeze flag
to sleep_thread.

Calling try_to_freeze() with a lock hold was done since day one in
f_mass_storage but since commit 0f9548ca1 ("lockdep: check that no
locks held at freeze time") lockdep complains about it.

Signed-off-by: George Cherian <george.cherian@ti.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 11:34:09 -06:00
Felipe Balbi
3f79265c96 usb: gadget: tcm_usb_gadget: mark bot_cleanup_old_alt static
that symbol is only used inside this function driver,
we should mark it static. Fixes sparse's:

drivers/usb/gadget/tcm_usb_gadget.c:373:6: warning: symbol \
	'bot_cleanup_old_alt' was not declared. Should it \
	be static?

Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 11:19:41 -06:00
Felipe Balbi
63b12e3ece usb: gadget: ffs: fix sparse warning
use NULL instead of 0 as pointer.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 11:16:49 -06:00
Fengguang Wu
d07a59019d usb: gadget: zero: module parameters can be static
g_zero's module parameters can, and should, be
static. This fixes sparse warnings.

Cc: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 11:12:15 -06:00
Felipe Balbi
f91d2f4337 usb: gadget: storage: fix sparse warning
fsg_common_set_inquiry_string() expects pointers
as second and third argument. Let's fix that by
passing NULL instead of plain 0 just so we silence
sparse's:

drivers/usb/gadget/f_mass_storage.c:3114:60: warning: \
	Using plain integer as NULL pointer
drivers/usb/gadget/f_mass_storage.c:3114:63: warning: \
	Using plain integer as NULL pointer

Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 11:07:46 -06:00
Valentine Barshak
c8ba8115a2 usb: phy: phy-rcar-gen2-usb: fix phy initialization
Add missing USB UGCTRL2 register offset.

Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:56:55 -06:00
Wei Yongjun
e8d68f88bc usb: phy: phy-generic: fix return value check in usb_nop_xceiv_register()
In case of error, the function platform_device_register_simple() returns
ERR_PTR() and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().

Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:56:48 -06:00
Alan Stern
a535d81c92 usb: dwc3: fix implementation of endpoint wedge
The dwc3 UDC driver doesn't implement endpoint wedging correctly.
When an endpoint is wedged, the gadget driver should be allowed to
clear the wedge by calling usb_ep_clear_halt().  Only the host is
prevented from resetting the endpoint.

This patch fixes the implementation.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Pratyush Anand <pratyush.anand@st.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:56:45 -06:00
Pratyush Anand
655403c212 usb: gadget: mass storage: fix return of delayed status
Mass storage gadget returns DELAYED_STATUS in stead of
USB_GADGET_DELAYED_STATUS while handling bulk reset request. Since
peripheral driver uses USB_GADGET_DELAYED_STATUS for delayed status
handling, therefore replace DELAYED_STATUS by USB_GADGET_DELAYED_STATUS
in mass storage driver.

Since, DELAYED_STATUS and hence EP0_BUFSIZE will no longer be used now,
so remove them.

Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Cc: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:56:33 -06:00
Andrzej Pietrasiewicz
bc912b0d23 usb: gadget: f_mass_storage: fix mass storage dependency
Legacy gadgets supporting mass storage (g_mass_storage, g_acm_ms, g_multi)
all depend on BLOCK.

Make the standalone compilation of f_mass_storage (without any legacy
gadget) dependent no BLOCK, too.

Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:54:31 -06:00
Jisheng Zhang
97a27f7340 usb: phy: phy-mxs-usb: set the correct platform drvdata
We need to set mxs_phy rather as the platform drvdata so that we can get
the correct mxs_phy in mxs_phy_remove().

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:54:25 -06:00
Sebastian Andrzej Siewior
66fadea5b7 usb: musb: only cancel work if it is initialized
Since commit c5340bd14 ("usb: musb: cancel work on removal") the workqueue
is cancelled but then if we bail out before the workqueue is setup we
get this:

|INFO: trying to register non-static key.
|the code is fine but needs lockdep annotation.
|turning off the locking correctness validator.
|CPU: 0 PID: 708 Comm: modprobe Not tainted 3.12.0+ #435
|[<c00867bc>] (lock_acquire+0xf0/0x108) from [<c00529d0>] (flush_work+0x38/0x2ec)
|[<c00529d0>] (flush_work+0x38/0x2ec) from [<c0052d24>] (__cancel_work_timer+0xa0/0x134)
|[<c0052d24>] (__cancel_work_timer+0xa0/0x134) from [<bf0e4ae4>] (musb_free+0x40/0x60 [musb_hdrc])
|[<bf0e4ae4>] (musb_free+0x40/0x60 [musb_hdrc]) from [<bf0e5364>] (musb_probe+0x678/0xb78 [musb_hdrc])
|[<bf0e5364>] (musb_probe+0x678/0xb78 [musb_hdrc]) from [<c0294bf0>] (platform_drv_probe+0x1c/0x24)
|[<c0294bf0>] (platform_drv_probe+0x1c/0x24) from [<c0293970>] (driver_probe_device+0x90/0x224)
|[<c0293970>] (driver_probe_device+0x90/0x224) from [<c0291ef0>] (bus_for_each_drv+0x60/0x8c)
|[<c0291ef0>] (bus_for_each_drv+0x60/0x8c) from [<c02938bc>] (device_attach+0x80/0xa4)
|[<c02938bc>] (device_attach+0x80/0xa4) from [<c0292b24>] (bus_probe_device+0x88/0xac)
|[<c0292b24>] (bus_probe_device+0x88/0xac) from [<c0291490>] (device_add+0x388/0x6c8)
|[<c0291490>] (device_add+0x388/0x6c8) from [<c02952a0>] (platform_device_add+0x188/0x22c)
|[<c02952a0>] (platform_device_add+0x188/0x22c) from [<bf11ea30>] (dsps_probe+0x294/0x394 [musb_dsps])
|[<bf11ea30>] (dsps_probe+0x294/0x394 [musb_dsps]) from [<c0294bf0>] (platform_drv_probe+0x1c/0x24)
|platform musb-hdrc.1.auto: Driver musb-hdrc requests probe deferral
|musb-hdrc musb-hdrc.1.auto: musb_init_controller failed with status -517

This patch moves the init part to earlier part so it can be cleaned as
part of the fail3 label because now it is surrounded by the fail4 label.
Step two is to remove it from musb_free() and add it to the two cleanup
paths (error path and device removal) separately.

Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:54:21 -06:00
Michael Grzeschik
2bac51a182 usb: gadget: composite: reset delayed_status on reset_config
The delayed_status value is used to keep track of status response
packets on ep0. It needs to be reset or the set_config function would
still delay the answer, if the usb device got unplugged while waiting
for setup_continue to be called.

Cc: stable@vger.kernel.org
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:54:17 -06:00
Sebastian Andrzej Siewior
a655f481d8 usb: musb: musb_cppi41: handle pre-mature TX complete interrupt
The TX-complete interrupt of the CPPI41 on AM335x fires too early.
Adding a loop and counting how long it takes until the
MUSB_TXCSR_TXPKTRDY bit is cleared I see
FS:
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadc54002, len=1514 is_tx=1
|cppi41_dma_callback() 74 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8802, len=1514 is_tx=1
|cppi41_dma_callback() 66 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadcd8002, len=1514 is_tx=1
|cppi41_dma_callback() 136 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=64, mode=0, dma_addr=0xadf55802, len=1514 is_tx=1
|cppi41_dma_callback() 136 loops

avg: 110 - 150us

HS:
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xaca6f002, len=1514 is_tx=1
|cppi41_dma_callback() 0 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f802, len=1514 is_tx=1
|cppi41_dma_callback() 2 loops
|musb-hdrc musb-hdrc.0.auto: configure ep1/80 packet_sz=512, mode=0, dma_addr=0xadd6f002, len=1514 is_tx=1
|cppi41_dma_callback() 13 loops

avg: 2us

for the same test case. One loop means a udelay(1). The delay seems to
depend on the packet size. On HS the bit is always cleared for small
packet sizes while on FS it is never the case, it mostly around 110us.
This testing has been performed with g_ether (musb as device) and using BULK
transfers.

INTR transfers are way more fun: during init the gadget sends a INT
packet to the host and cppi41 says "transfer done" shortly after. The
MUSB_TXCSR_TXPKTRDY bit is set even seconds later. The reason is that the host
did not try to receive it, it does so after the interface (on host side) has
been configured. Until this happens, that packet remains in musb's FIFO.

To fix this, two things are done:
- No DMA transfers for INT based endpoints. These transfer are usually
  very small and rare so it is likely better to skip the DMA engine and
  stuff the four bytes directly into the FIFO
- on HS we poll up to 25us and hope that bit goes away. If not we setup
  a hrtimer to poll for it. The 140us delay is a rule of thumb. In FS
  the command
  | ping 10.10.10.10 -c1 -s65130
  creates about 44 1514bytes transfers. About 19 of them need a second
  timer to complete.

Reported-by: Bin Liu <b-liu@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:54:14 -06:00
Sebastian Andrzej Siewior
d373a8534d usb: musb: musb_cppi41: factor most of cppi41_dma_callback() into cppi41_trans_done()
This patch moves most of the logic in cppi41_dma_callback() into
cppi41_trans_done() where it can be called from another function.
Instead of computing "transferred" (the number of bytes transferred in
the last transaction) in cppi41_trans_done() the member
"cppi41_channel->prog_len" is now set to 0 if the transfer as a whole
can be considered as done. If it is != 0 then the next iteration is
assumed.
This is a preparation for a workaround.

Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:54:06 -06:00
Johan Hovold
043e3f8345 USB: serial: fix write memory-allocation flag
Fix regression introduced by commit 818f60365a ("USB: serial: add
memory flags to usb_serial_generic_write_start"), which incorrectly used
GFP_KERNEL in write(), which must not not sleep.

Reported-by: Dave Jones <davej@fedoraproject.org>
Tested-by: Dave Jones <davej@fedoraproject.org>
Cc: Dave Jones <davej@fedoraproject.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-11-25 08:39:40 -08:00
Johan Hovold
6f6485463a USB: serial: fix race in generic write
Fix race in generic write implementation, which could lead to
temporarily degraded throughput.

The current generic write implementation introduced by commit
27c7acf220 ("USB: serial: reimplement generic fifo-based writes") has
always had this bug, although it's fairly hard to trigger and the
consequences are not likely to be noticed.

Specifically, a write() on one CPU while the completion handler is
running on another could result in only one of the two write urbs being
utilised to empty the remainder of the write fifo (unless there is a
second write() that doesn't race during that time).

Cc: stable <stable@vger.kernel.org> # 2.6.35
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-11-25 08:39:40 -08:00
Heikki Krogerus
37cfbc4288 usb: phy: generic: fix a compiler warning
Just because it annoys me.

Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:25:59 -06:00
Aaro Koskinen
dc52c57411 usb: phy-generic: fix nop xceiv probe
Commit bd27fa44e1 (usb: phy: generic:
Don't use regulator framework for RESET line) introduced regression: All
users of usb_nop_xceiv_register() will fail because there is no platform
data and the default reset GPIO is 0 which is a valid GPIO. Fix that.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:25:59 -06:00
Apelete Seketeli
fd3923a990 usb: fix musb gadget to enable OTG mode conditionally
The musb driver is usable in host, gadget or dual role mode depending
on the kernel configuration.

However, the musb gadget part of the driver is enabling OTG mode
whether the driver is built for dual role or gadget only mode. This
induces a bug for gadget only USB device controllers where the kernel
tries to use Host Negotiation Protocol with such controllers, which
causes a panic.

This behaviour is now fixed by enabling OTG mode only when musb driver
is built for dual role mode.

Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:25:58 -06:00
Linus Walleij
b144e4ab1e usb: gadget: fix pxa25x compilation problems
In commit
88f718e3fa
"ARM: pxa: delete the custom GPIO header"
we removed the implicit inclusion of <mach/gpio.h>
from <linux/gpio.h>.

The pxa25x_udc was not using that, but it was relying
on <linux/gpio.h> to implictly include <mach/gpio.h>
which in turn implicitly included <mach/hardware.h>,
which was needed for the driver to compile.

Fix this up by explicitly including the necessary
<mach/hardware.h> header.

Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:25:58 -06:00
Robert Baldyga
d18f7116a5 usb: gadget: s3c-hsotg: fix disconnect handling
This patch moves s3c_hsotg_disconnect function call from USBSusp interrupt
handler to SET_ADDRESS request handler.

It's because disconnected state can't be detected directly, because this
hardware doesn't support Disconnected interrupt for device mode. For both
Suspend and Disconnect events there is one interrupt USBSusp, but calling
s3c_hsotg_disconnect from this interrupt handler causes config reset in
composite layer, which is not undesirable for Suspended state.

For this reason s3c_hsotg_disconnect is called from SET_ADDRESS request
handler, which occurs always after disconnection, so we do disconnect
immediately before we are connected again. It's probably only way we
can do handle disconnection correctly.

Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
2013-11-25 10:25:58 -06:00