Make single kernel can be used on RBTX4927/37/38. Also make
some SoC-specific code independent from board-specific code.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Split out PCIC dependent code and SoC dependent code from board dependent
code. Now TX4927 PCIC code is independent from TX4927/TX4938 SoC code.
Also fix some build problems on CONFIG_PCI=n.
As a bonus, "FPCIB0 Backplane Support" is available for all TX39/TX49 boards
and PCI66 support is available for all TX49 boards.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move arch/mips/{jmr3927,tx4927,tx4938} into arch/mips/txx9/ tree.
This will help more code sharing and maintainance.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Never terribly functional or popular, plagued by hard to fix bugs the time
to say goodbye has more than arrived.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The introduction of a real dma cache invalidate makes it important
to have a correct cache line size, otherwise the kernel will gives
out two memory segment, which might share one cache line. The R4400
Indy/Indigo2 CPU modules are using a second level cache line size
of 128 bytes, so MIPS_L1_CACHE_SHIFT needs to be bumped up to 7 for
IP22.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This converts mips to use the new helpers for smp_call_function() and
friends, and adds support for smp_call_function_single(). Not tested,
but it compiles.
mips shares the same IPI for smp_call_function() and
smp_call_function_single(), since not all mips platforms have enough
available IPIs to support seperate setups.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This is a board-independent TXx9 gpio API implementation using gpiolib.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This allows a 48Hz clock to be selected on Malta and other systems. Note
this not normally a sensible option as it results in rather high latencies
for some kernel stuff.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To allow flexible configuration of IDE introduce HAVE_IDE.
All archs except arm, um and s390 unconditionally select it.
For arm the actual configuration determine if IDE is supported.
This is a step towards introducing drivers/Kconfig for arm.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
After seeing the filename I'd have expected something about the
implementation of SMP in the Linux kernel - not some notes on kernel
configuration and building trivialities noone would search at this
place.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Alan Cox <alan@redhat.com>
Linus:
On the per-architecture side, I do think it would be better to *not* have
internal architecture knowledge in a generic file, and as such a line like
depends on X86_32 || IA64 || PPC || S390 || SPARC64 || X86_64 || AVR32
really shouldn't exist in a file like kernel/Kconfig.instrumentation.
It would be much better to do
depends on ARCH_SUPPORTS_KPROBES
in that generic file, and then architectures that do support it would just
have a
bool ARCH_SUPPORTS_KPROBES
default y
in *their* architecture files. That would seem to be much more logical,
and is readable both for arch maintainers *and* for people who have no
clue - and don't care - about which architecture is supposed to support
which interface...
Changelog:
Actually, I know I gave this as the magic incantation, but now that I see
it, I realize that I should have told you to just use
config ARCH_SUPPORTS_KPROBES
def_bool y
instead, which is a bit denser.
We seem to use both kinds of syntax for these things, but this is really
what "def_bool" is there for...
Changelog :
- Moving to HAVE_*.
- Add AVR32 oprofile.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* 'suspend' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (38 commits)
suspend: cleanup reference to swsusp_pg_dir[]
PM: Remove obsolete /sys/devices/.../power/state docs
Hibernation: Invoke suspend notifications after console switch
Suspend: Invoke suspend notifications after console switch
Suspend: Clean up suspend_64.c
Suspend: Add config option to disable the freezer if architecture wants that
ACPI: Print message before calling _PTS
ACPI hibernation: Call _PTS before suspending devices
Hibernation: Introduce begin() and end() callbacks
ACPI suspend: Call _PTS before suspending devices
ACPI: Separate disabling of GPEs from _PTS
ACPI: Separate invocations of _GTS and _BFS from _PTS and _WAK
Suspend: Introduce begin() and end() callbacks
suspend: fix ia64 allmodconfig build
ACPI: clear GPE earily in resume to avoid warning
Suspend: Clean up Kconfig (V2)
Hibernation: Clean up Kconfig (V2)
Hibernation: Update messages
Suspend: Use common prefix in messages
Hibernation: Remove unnecessary variable declaration
...
This cleans up the suspend Kconfig and removes the need to
declare centrally which architectures support suspend. All
architectures that currently support suspend are modified
accordingly.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Paul Mackerras <paulus@samba.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Pavel Machek <pavel@suse.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
A HOWTO that hasn't been updated for half a dozen years no longer
"contains valuable information about which PCI hardware does work under
Linux and which doesn't".
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The break_lock data structure and code for spinlocks is quite nasty.
Not only does it double the size of a spinlock but it changes locking to
a potentially less optimal trylock.
Put all of that under CONFIG_GENERIC_LOCKBREAK, and introduce a
__raw_spin_is_contended that uses the lock data itself to determine whether
there are waiters on the lock, to be used if CONFIG_GENERIC_LOCKBREAK is
not set.
Rename need_lockbreak to spin_needbreak, make it use spin_is_contended to
decouple it from the spinlock implementation, and make it typesafe (rwlocks
do not have any need_lockbreak sites -- why do they even get bloated up
with that break_lock then?).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Qemu platform was originally implemented to have an easily supportable
platform until Qemu reaches a state where it emulates a real world system.
Since the latest release Qemu is capable of emulating the MIPSsim and
Malta platforms, so this goal has been reached. The Qemu plaform is also
rather underfeatured so less useful than a Malta emulation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Moved the eXcite local config to excite directory.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A raw binary boots about twice as fast as SREC.
The possibility to generate SREC binaries remains by simply using the
vmlinux.srec target but seems only useful for the probably hypothetical
case where one of these systems is booted over a serial interface.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- EISA support for non PCI RMs (RM200 and RM400-xxx). The major part
is the splitting of the EISA and onboard ISA of the RM200, which
makes the EISA bus on the RM200 look like on other RMs.
- 64bit kernel support
- system type detection is now common for big and little endian
- moved sniprom code to arch/mips/fw
- added call_o32 function to arch/mips/fw/lib, which uses a private
stack for calling prom functions
- fix problem with ISA interrupts, which makes using PIT clockevent
possible
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for SGI IP28 machines (Indigo 2 with R10k CPUs)
This work is mainly based on Peter Fuersts work.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
According to Broadcom the PT systems are production test systems which
never reached customers so no need to keep the fragmentary support we
currently have.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move registration into the actual platform code instead of making a
desparate attempt at sharing the hand full of likes of code in pcspeaker.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the gereric part of R4000/R4400 errata workarounds. They include
compiler and assembler support as well as some source code modifications
to address the problems with some combinations of multiply/divide+shift
instructions as well as the daddi and daddiu instructions.
Changes included are as follows:
1. New Kconfig options to select workarounds by platforms as necessary.
2. Arch top-level Makefile to pass necessary options to the compiler; also
incompatible configurations are detected (-mno-sym32 unsupported as
horribly intrusive for little gain).
3. Bug detection updated and shuffled -- the multiply/divide+shift problem
is lethal enough that if not worked around it makes the kernel crash in
time_init() because of a division by zero; the daddiu erratum might
also trigger early potentially, though I have not observed it. On the
other hand the daddi detection code requires the exception subsystem to
have been initialised (and is there mainly for information).
4. r4k_daddiu_bug() added so that the existence of the erratum can be
queried by code at the run time as necessary; useful for generated code
like TLB fault and copy/clear page handlers.
5. __udelay() updated as it uses multiplication in inline assembly.
Note that -mdaddi requires modified toolchain (which has been maintained
by myself and available from my site for ~4years now -- versions covered
are GCC 2.95.4 - 4.1.2 and binutils from 2.13 onwards). The -mfix-r4000
and -mfix-r4400 have been standard for a while though.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The patch below fixes two problems for Kconfig on the BCM47xx platform:
- arch/mips/bcm47xx/gpio.c uses ssb_extif_* functions. Selecting
SSB_DRIVER_EXTIF makes sure those functions are available.
- arch/mips/pci/pci.c needs, when enabled, platform specific functions,
which are defined when SSB_PCICORE_HOSTMODE is enabled.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CONFIG_NO_HZ, CONFIG_HIGH_RES_TIMERS should be selected in "Kernel
type" menu, not in "CPU selection" menu.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The cleanup 09cadedbdc broke the oprofile
configuration for MIPS by allowing oprofile support to be built for
kernel models where oprofile doesn't have a chance in hell to work.
Just a dependecy list on a number of architectures is - surprise - broken
and should as per past discussions probably in most considered to be
broken in most cases. So I introduce a dependency for the oprofile
configuration on ARCH_SUPPORTS_OPROFILE.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sibyte SOCs only have 32-bit PCI. Due to the sparse use of the address
space only the first 1GB of memory is mapped at physical addresses
below 1GB. If a system has more than 1GB of memory 32-bit DMA will
not be able to reach all of it.
For now this patch is good enough to keep Sibyte users happy but it seems
eventually something like swiotlb will be needed for Sibyte.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In particular as-is it's not suited for multicore and mutiprocessors
systems where there is on guarantee that the counter are synchronized
or running from the same clock at all. This broke Sibyte and probably
others since the "[MIPS] Handle R4000/R4400 mfc0 from count register."
commit.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Shadow register support would not possibly have worked on multicore
systems. The support code for it was also depending not on MIPS R2 but
VSMP or SMTC kernels even though it makes perfect sense with UP kernels.
SR sets are a scarce resource and the expected usage pattern is that
users actually hardcode the register set numbers in their code. So fix
the allocator by ditching it. Move the remaining CPU probe bits into
the generic CPU probe.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert jmr3927_clock_event_device to more generic
txx9tmr_clock_event_device which supports one-shot mode. The
txx9tmr_clock_event_device can be used for TX49 too if the cp0 timer
interrupt was not available.
Convert jmr3927_hpt_read to txx9_clocksource driver which does not
depends jiffies anymore. The txx9_clocksource itself can be used for
TX49, but normally TX49 uses higher precision clocksource_mips.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
And make use of it for Cobalt. A few others such as the Malta could make
use of it as well.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most of these fixes were already submitted for old kernel versions, and were
approved, but for some reason they never made it into the releases.
Because this is a consolidation of a couple old missed patches, it touches both
Kconfigs and documentation texts.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Quoting Randy:
"It seems sad that this patch sources Kconfig.marker, a 7-line file,
20-something times. Yes, you (we) don't want to put those 7 lines into
20-something different files, so sourcing is the right thing.
However, what you did for avr32 seems more on the right track to me: make
_one_ Instrumentation support menu that includes PROFILING, OPROFILE, KPROBES,
and MARKERS and then use (source) that in all of the arches."
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The kernel currently only supports broadcasting of the timer interrupt
from a single timer, not multicasting into two multicast groups of
processors. So the implemented mechanism for SMTC works by broadcasting
the cp0 compare interrupt on VPE 0 and ignoring it on any additional VPEs.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This replaces the MIPS-specific to_tm function with the generic
rtc_time_to_tm function. The big difference between the two functions is
that rtc_time_to_tm uses epoch 70 while to_tm uses 1970, so the result of
rtc_time_to_tm needs to be fixed up.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add CFE support to the BCM47XX code. That includes querying CFE environment
variables as well as using CFE to print messages before the serial port is
initialized (early printk).
Signed-off-by: Aurelien Jarno <aurel32@farad.aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the platform independent part of the CFE code to arch/mips/fw/cfe from
arch/mips/sibyte/cfe.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Note that the BCM4710 does not support the wait instruction, this
is not a mistake in the code.
It originally comes from the OpenWrt patches.
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Florian Schirmer <jolt@tuxbox.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We do not rely on user anymore to setup this config correctly.
Instead we make our choice depending on the load address.
If we want to force Kbuild to use ELF64 format whatever
the load address we can still do:
$ make BUILD_ELF32=no
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/basler/excite/excite_prom.o
arch/mips/basler/excite/excite_prom.c:136:3: #error 64 bit support not implemented
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add generic irq_chip for TX39/TX49 SoCs. This can be replace
jmr3927_irq_irc, tx4927_irq_pic_type and tx4938_irq_pic_type.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
While the PC speaker is wired up to the i8254 there is more to the i8254
than just the PC speaker so this code was getting in the way under its
current name.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To support multiple TC microthreads acting as "CPUs" within a VPE,
VPE-wide interrupt mask bits must be specially manipulated during
interrupt handling. To support legacy drivers and interrupt controller
management code, SMTC has a "backstop" to track and if necessary restore
the interrupt mask. This has some performance impact on interrupt service
overhead. Disable it only if you know what you are doing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GPIO 0..15 are for TX4938 PIO pins, GPIO 16..18 are for FPGA-driven
chipselect signals for SPI devices.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- use RTC_CLASS instead of GEN_RTC
- get rid of ds1216 in favour of a RTC_CLASS driver
- use correct console device for older RM400
- use physical addresses for 82596 device
- use 128 byte L1 cache line size (this is needed because most of the
SNI caches are using 128 L2 cache lines)
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add mips common support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is an optimised implementation of early printk() for the DECstation.
After the recent conversion to a MIPS-specific generic routine using a
character-by-character output the performance dropped significantly.
This change reverts to the previous speed -- even at 9600 bps of the
serial console the difference is visible with a naked eye; I presume for a
framebuffer it is even worse (it may depend on exactly which one is used
though).
Additionally the change includes a fix for a problem that the old
implementation had -- the format used would not actually limit the length
of the string output. This new implementation uses a local buffer to deal
with it -- even with this additional copying it is much faster than the
generic function.
Plus this driver is registered much earlier than the generic one,
allowing one to see critical messages, such as one about an incorrect CPU
setting used, that are produced beforehand. :-)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are no I/O ports on the DECstation whatsoever in any configuration
as neither the CPU nor the peripheral buses used have a concept of such.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the generic GPIO API to Au1x00 boards. It requires
the generic GPIO patch for MIPS boards by Yoichi Yuasa. Now there is a MIPS
target using it, can you queue these patchset for 2.6.22 ? Thank you very
much in advance.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It has some hackish code and it odd DMA results in the need to support
old features in kernel code.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Those boards do not need CONFIG_ISA if the ne driver could be
selectable without it. Disable it and update a defconfig.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for the integrated serial ports of the MIPS RM9122 processor
and its relatives.
The patch also does some whitespace cleanup.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch has removed 2 select entries for VR41xx.
These entries are selected in arch/mips/vr41xx/Kconfig.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch has merged GT64111 PCI routines and GT64120 PCI_0 routines.
GT64111 PCI is almost the same as GT64120's PCI_0.
This patch don't change GT64120 PCI routines.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
So until MIPS_MT_SMTC_INSTANT_REPLAY has been rewritten to solve this
issue, don't allow selecting it with PREEMPT.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Might be useful for SMP debugging.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
[Rewritten Kconfig bits to deal better fit in the usual pattern of doing
things - Ralf]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A defconfig file and the 10 lines of code (including comments ...) that
are rotting since lmo commit 6516a42dc8b40c6c00010346dd51496125b16644
don't quite make proper support, so let's trash it.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The generic rtc-ds1742 driver can be used for RBTX4927 and JMR3927
(with __swizzle_addr trick). This patch also removes MIPS local
DS1742 stuff.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds trivial support for SMARTMIPS extension. This extension
is currently implemented by 4KS[CD] CPUs.
Basically it saves/restores ACX register, which is part of the SMARTMIPS
ASE, when needed. This patch does *not* add any support for Smartmips MMU
features.
Futhermore this patch does not add explicit support for 4KS[CD] CPUs since
they are respectively mips32 and mips32r2 compliant. So with the current
processor configuration, a platform that has such CPUs needs to select
both configs:
CPU_HAS_SMARTMIPS
SYS_HAS_CPU_MIPS32_R[12]
This is due to the processor configuration which is mixing up all the
architecture variants and the processor types.
The drawback of this, is that we currently pass '-march=mips32' option to
gcc when building a kernel instead of '-march=4ksc' for 4KSC case. This
can lead to a kernel image a little bit bigger than required.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Platforms will now have to supply a function dma_device_is_coherent which
returns if a particular device participates in the coherence domain. For
most platforms this function will always return 0 or 1.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] signal: do not inline handle_signal()
[MIPS] signal: do not use save_static_function() anymore
[MIPS] signal32: no need to save c0_status register in setup_sigcontext32()
[MIPS] signal32: reduce {setup,restore}_sigcontext32 sizes
[MIPS] signal: factorize debug code
[MIPS] signal: test return value of install_sigtramp()
[MIPS] signal32: remove duplicate code
[MIPS] signal: clean up sigframe structure
[MIPS] signal: do not inline functions in signal-common.h
[MIPS] signals: reduce {setup,restore}_sigcontext sizes
[MIPS] Fix warning in get_user when fetching pointer object from userspace.
[MIPS] Fix eth2 platform device id for jaguar_atx and ocelot_3 platforms
[MIPS] JMR3927 and RBTX49x7 support little endian
[MIPS] RBTX49x7: declare prom_getcmdline()
[MIPS] RTLX: Sprinkle device model code into code to make udev happier.
[MIPS] VPE: Sprinkle device model code into code to make udev happier.
As Andi pointed out: CONFIG_GENERIC_ISA_DMA only disables the ISA DMA
channel management. Other functionality may still expect GFP_DMA to
provide memory below 16M. So we need to make sure that CONFIG_ZONE_DMA is
set independent of CONFIG_GENERIC_ISA_DMA. Undo the modifications to
mm/Kconfig where we made ZONE_DMA dependent on GENERIC_ISA_DMA and set
theses explicitly in each arches Kconfig.
Reviews must occur for each arch in order to determine if ZONE_DMA can be
switched off. It can only be switched off if we know that all devices
supported by a platform are capable of performing DMA transfers to all of
memory (Some arches already support this: uml, avr32, sh sh64, parisc and
IA64/Altix).
In order to switch ZONE_DMA off conditionally, one would have to establish
a scheme by which one can assure that no drivers are enabled that are only
capable of doing I/O to a part of memory, or one needs to provide an
alternate means of performing an allocation from a specific range of memory
(like provided by alloc_pages_range()) and insure that all drivers use that
call. In that case the arches alloc_dma_coherent() may need to be modified
to call alloc_pages_range() instead of relying on GFP_DMA.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Toshiba JMR3927 (RBHMA3100) and RBTX49[23]7 (RBHMA4[24]00) do support both
little and big endian mode (if you flash the right PMON).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Also convert to use generic kernel/power/Kconfig to make the use of the
shared APM emulation possible.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently KEXEC is in "Machine selection", SECCOMP, PM, APM are in
"Executable file formats" menu. Move KEXEC and SECCOMP to "Kernel
type" and PM, APM to new "Power management options" menu. Also
replace "config PM" with kernel/power/Kconfig.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
SMTC pseudo-interrupts between TCs are deferred and queued if the target
TC is interrupt-inhibited (IXMT). In the first SMTC prototypes, these
queued IPIs were serviced on return to user mode, or on entry into the
kernel idle loop. The INSTANT_REPLAY option dispatches them as part of
local_irq_restore() processing, which adds runtime overhead (hence the
option to turn it off), but ensures that IPIs are handled promptly even
under heavy I/O interrupt load.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that i8259A_chip uses new irq flow handler select
GENERIC_HARDIRQS_NO__DO_IRQ on some more platforms.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__do_IRQ() is needed only by irq handlers that can't use
default handlers defined in kernel/irq/chip.c.
For others platforms there's no need to compile this function
since it won't be used. For those platforms this patch defines
GENERIC_HARDIRQS_NO__DO_IRQ symbol which is used exactly for
this purpose.
Futhermore for platforms which do not use __do_IRQ(), end()
method which is part of the 'irq_chip' structure is not used.
This patch simply removes this method in this case.
Signed-off-by: Franck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (31 commits)
[MIPS] Remove duplicate ISA DMA code for 0 DMA channel case.
[MIPS] Remove unused definition of cpu_to_lelongp()
[MIPS] Remove userspace proofing from <asm/bitops.h>.
[MIPS] Remove old junk left from old atomic_lock.
[MIPS] Use conditional traps for BUG_ON on MIPS II and better.
[MIPS] mips HPT cleanup: make clocksource_mips public
[MIPS] do_IRQ cleanup
[MIPS] Avoid dupliate D-cache flush on R400C / R4400 SC and MC variants.
[MIPS] Remove redundant r4k_blast_icache() calls
[MIPS] Work around bogus gcc warnings.
[MIPS] Fix double inclusions
[MIPS] use generic_handle_irq, handle_level_irq, handle_percpu_irq
[MIPS] IRQ cleanups
[MIPS] mips hpt cleanup: get rid of mips_hpt_init
[MIPS] PB1200: Remove duplicate definitions
[MIPS] Fix alignment hole in struct cache_desc; shrink struct.
[MIPS] Oprofile: kernel support for the R10000.
[MIPS] Remove unused R10000 performance counter definitions.
[MIPS] Add support for kexec
[MIPS] Don't print presence of WAIT instruction on bootup.
...
Fix various Kconfig typos.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
When lmo commit 4ef893e0515e8bf336dfbd200884f244869fbb43 was merged to
kernel.org as e73ea273ef patch happily
applied the IP27 segment to IP22. f63f36c18b11e166d0f362ac04dbcd7e6ea23f9e
did fix the effects partially - and with a wrong log message. Now fixed
for real (tm).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch happily applied an Ocelot G patch to Ocelot C when merging
linux-mips.org changeset 91ee9a801e65d2981dfe327d2519c7fc6ab02e6b into
kernel.org as 6ceb6d3ab2.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This reverts commit 31473747bd.
Another amazing example of patch(1) messing up - lmo changeset
66e8560d11d02bcadc261498471831a6375ad046 was merged twice to kernel.org
and ended up doing this rubbish job.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The cause of the build errors was a 64-bit kernel being configured in
ocelot_g_defconfig without the code being 64-bit proof. Fixed for now
by limiting 64-bit selection to SYS_SUPPORTS_64BIT_KERNEL if BROKEN.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the compilation errors on PNX8550 and hard-to-track
bug in interrupt handling.
It also corresponds to the latest changes in PNX8550 serial driver.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As per feature-removal-schedule.txt.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This very small patch adds support for little endian on the virtual QEMU
mips platform. The status of this platform is the same as the big endian
one, ie it is possible to boot a system with init=/bin/sh.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement stacktrace interface by using unwind_stack() and enable lockdep
support in Kconfig.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch introduces a number of configuration variables. These allow to
specify presence/absence of integrated peripherals found on the MIPS
RM9xxx processor family, based on the particular processor model used.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
1. MIPS should select SPARSEMEM_STATIC since allocating bootmem in
memory_present() will corrupt bootmap area.
2. pfn_valid() for SPARSEMEM is defined in linux/mmzone.h
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This might be helpfull to debug sparsemem on mips.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This might be helpfull to debug sparsemem on mips.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (33 commits)
[MIPS] Add missing backslashes to macro definitions.
[MIPS] Death list of board support to be removed after 2.6.18.
[MIPS] Remove BSD and Sys V compat data types.
[MIPS] ioc3.h: Uses u8, so include <linux/types.h>.
[MIPS] 74K: Assume it will also have an AR bit in config7
[MIPS] Treat CPUs with AR bit as physically indexed.
[MIPS] Oprofile: Support VSMP on 34K.
[MIPS] MIPS32/MIPS64 S-cache fix and cleanup
[MIPS] excite: PCI makefile needs to use += if it wants a chance to work.
[MIPS] excite: plat_setup -> plat_mem_setup.
[MIPS] au1xxx: export dbdma functions
[MIPS] au1xxx: dbdma, no sleeping under spin_lock
[MIPS] au1xxx: fix PSC_SMBTXRX_RSR.
[MIPS] Early printk for IP27.
[MIPS] Fix handling of 0 length I & D caches.
[MIPS] Typo fixes.
[MIPS] MIPS32/MIPS64 secondary cache management
[MIPS] Fix FIXADDR_TOP for TX39/TX49.
[MIPS] Remove first timer interrupt setup in wrppmc_timer_setup()
[MIPS] Fix configuration of R2 CPU features and multithreading.
...
o Fix the build error Wind River PPMC board caused by the change of
plat_setup hook interface.
o Rewrite first level interrupt dispatch code to C.
Signed-off-by: Rongkai.Zhan <rongkai.zhan@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make HZ configurable. DECSTATION can select 128/256/1024 HZ, JAZZ can
only select 100 HZ, others can select 100/128/250/256/1000/1024 HZ if
not explicitly specified). Also remove all mach-xxx/param.h files and
update all defconfigs according to current HZ value.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Added support for RM200C machines with big endian firmware
Added support for RM200-C40 (R5000 support)
Signed-off-by: Florian Lohoff <flo@rfc822.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IP27 configuration isn't the only NUMA system - it just happens to be
the currently only supported MIPS NUMA system. So move the necessary
options back into the main MIPS Kconfig file.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Support for the GT-64120-based Wind River 4KC PPMC Evaluation board.
Signed-off-by: Rongkai.Zhan <Rongkai.zhan@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The "system type" Kconfig options on MIPS are not consistent. For
some platforms, only the name is listed while other entries are
prepended with "Support for". Remove this as it doesn't make sense
when describing the "system type".
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
