Pull networking fixes from David Miller:
1) Revert regression inducing change to the IPSEC template resolver,
from Steffen Klassert.
2) Peeloffs can cause the wrong sk to be waken up in SCTP, fix from Xin
Long.
3) Min packet MTU size is wrong in cpsw driver, from Grygorii Strashko.
4) Fix build failure in netfilter ctnetlink, from Arnd Bergmann.
5) ISDN hisax driver checks pnp_irq() for errors incorrectly, from
Arvind Yadav.
6) Fix fealnx driver build failure on MIPS, from Huacai Chen.
7) Fix into leak in SCTP, the scope_id of socket addresses is not
always filled in. From Eric W. Biederman.
8) MTU inheritance between physical function and representor fix in nfp
driver, from Dirk van der Merwe.
9) Fix memory leak in rsi driver, from Colin Ian King.
10) Fix expiration and generation ID handling of cached ipv4 redirect
routes, from Xin Long.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
net: usb: hso.c: remove unneeded DRIVER_LICENSE #define
ibmvnic: fix dma_mapping_error call
ipvlan: NULL pointer dereference panic in ipvlan_port_destroy
route: also update fnhe_genid when updating a route cache
route: update fnhe_expires for redirect when the fnhe exists
sctp: set frag_point in sctp_setsockopt_maxseg correctly
rsi: fix memory leak on buf and usb_reg_buf
net/netlabel: Add list_next_rcu() in rcu_dereference().
nfp: remove false positive offloads in flower vxlan
nfp: register flower reprs for egress dev offload
nfp: inherit the max_mtu from the PF netdev
nfp: fix vlan receive MAC statistics typo
nfp: fix flower offload metadata flag usage
virto_net: remove empty file 'virtio_net.'
net/sctp: Always set scope_id in sctp_inet6_skb_msgname
fealnx: Fix building error on MIPS
isdn: hisax: Fix pnp_irq's error checking for setup_teles3
isdn: hisax: Fix pnp_irq's error checking for setup_sedlbauer_isapnp
isdn: hisax: Fix pnp_irq's error checking for setup_niccy
isdn: hisax: Fix pnp_irq's error checking for setup_ix1micro
...
Merge updates from Andrew Morton:
- a few misc bits
- ocfs2 updates
- almost all of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (131 commits)
memory hotplug: fix comments when adding section
mm: make alloc_node_mem_map a void call if we don't have CONFIG_FLAT_NODE_MEM_MAP
mm: simplify nodemask printing
mm,oom_reaper: remove pointless kthread_run() error check
mm/page_ext.c: check if page_ext is not prepared
writeback: remove unused function parameter
mm: do not rely on preempt_count in print_vma_addr
mm, sparse: do not swamp log with huge vmemmap allocation failures
mm/hmm: remove redundant variable align_end
mm/list_lru.c: mark expected switch fall-through
mm/shmem.c: mark expected switch fall-through
mm/page_alloc.c: broken deferred calculation
mm: don't warn about allocations which stall for too long
fs: fuse: account fuse_inode slab memory as reclaimable
mm, page_alloc: fix potential false positive in __zone_watermark_ok
mm: mlock: remove lru_add_drain_all()
mm, sysctl: make NUMA stats configurable
shmem: convert shmem_init_inodecache() to void
Unify migrate_pages and move_pages access checks
mm, pagevec: rename pagevec drained field
...
As the page free path makes no distinction between cache hot and cold
pages, there is no real useful ordering of pages in the free list that
allocation requests can take advantage of. Juding from the users of
__GFP_COLD, it is likely that a number of them are the result of copying
other sites instead of actually measuring the impact. Remove the
__GFP_COLD parameter which simplifies a number of paths in the page
allocator.
This is potentially controversial but bear in mind that the size of the
per-cpu pagelists versus modern cache sizes means that the whole per-cpu
list can often fit in the L3 cache. Hence, there is only a potential
benefit for microbenchmarks that alloc/free pages in a tight loop. It's
even worse when THP is taken into account which has little or no chance
of getting a cache-hot page as the per-cpu list is bypassed and the
zeroing of multiple pages will thrash the cache anyway.
The truncate microbenchmarks are not shown as this patch affects the
allocation path and not the free path. A page fault microbenchmark was
tested but it showed no sigificant difference which is not surprising
given that the __GFP_COLD branches are a miniscule percentage of the
fault path.
Link: http://lkml.kernel.org/r/20171018075952.10627-9-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now CPSW driver configures min eth packet size to 60 octets (ETH_ZLEN)
which works in most of cases, but when port VLAN is configured on some
switch port, it also can be configured to force all egress packets to be
VLAN untagged. And in this case, CPSW driver will pad small packets to 60
octets, but final packet size on port egress can became less than 60 octets
due to VLAN tag removal and packet will be dropped.
Hence, fix it by accounting VLAN header in CPSW min eth packet size. While
here, use proper defines for CPSW_MAX_PACKET_SIZE also, instead of open
coding.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Samuel Chessman <chessman@tux.org>
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't remove rx_napi specifically just before free_netdev(),
it's supposed to be done in it and is confusing w/o tx_napi deletion.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is quite common for ti_cm_get_macid() to fail on some of the
platforms it is invoked on. They include any platform where
mac address is not part of SoC register space.
On these platforms, mac address is read and populated in
device-tree by bootloader. An example is TI DA850.
Downgrade the severity of message to "information", so it does
not spam logs when 'quiet' boot is desired.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
@match disable optional_qualifier@
identifier s;
@@
static struct ptp_clock_info s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
position ref.p;
identifier match.s,f,c;
expression e;
@@
(
e = s@p
|
e = s@p.f
|
c(...,s@p.f,...)
|
c(...,s@p,...)
)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct ptp_clock_info s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_device_id are not supposed to change at runtime. All functions
working with platform_device_id provided by <linux/platform_device.h>
work with const platform_device_id. So mark the non-const structs as
const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frequency can be adjusted in DT it make sense to
print current used value on driver init.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Polling 14 mdio devices on single mdio bus eats 30% of 1Ghz cpu time
due to busy loop in wait(). Add small delay to relax cpu.
Signed-off-by: Max Uvarov <muvarov@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of struct tc_to_netdev which is now just unnecessary container
and rather pass per-type structures down to drivers directly.
Along with that, consolidate the naming of per-type structure variables
in cls_*.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the return value from -EINVAL to -EOPNOTSUPP. The rest of the
drivers have it like that, so be aligned.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As ndo_setup_tc is generic offload op for whole tc subsystem, does not
really make sense to have cls-specific args. So move them under
cls_common structurure which is embedded in all cls structs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the type is always present, push it to be a separate argument to
ndo_setup_tc. On the way, name the type enum and use it for arg type.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now the call chain
cpts_find_ts()
|- cpts_fifo_read(cpts, CPTS_EV_PUSH)
will stop reading CPTS FIFO if PUSH event is found. But this is not
expected and CPTS FIFI should be completely drained here. This is most
probably copy-paste error and it has no negative impact as CPTS_EV_PUSH
should not be present in FIFO without TS_PUSH request and
cpts_systim_read() and cpts_find_ts() synchronized by spin_lock.
Correct above by calling cpts_fifo_read() with -1 parameter, so it will
read all CPTS event from FIFO.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the low speed Ethernet connection CPDMA notification about packet
processing can be received before CPTS TX timestamp event, which is set
when packet actually left CPSW while cpdma notification is sent when packet
pushed in CPSW fifo. As result, when connection is slow and CPU is fast
enough TX timestamping is not working properly.
Fix it, by introducing TX SKB queue to store PTP SKBs for which Ethernet
Transmit Event hasn't been received yet and then re-check this queue
with new Ethernet Transmit Events by scheduling CPTS overflow
work more often (every 1 jiffies) until TX SKB queue is not empty.
Side effect of this change is:
- User space tools require to take into account possible delay in TX
timestamp processing (for example ptp4l works with tx_timestamp_timeout=400
under net traffic and tx_timestamp_timeout=25 in idle).
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There could be significant delay in CPTS work schedule under high system
load and on -RT which could cause CPTS misbehavior due to internal counter
overflow. Usage of own kthread_worker allows to avoid such kind of issues
and makes it possible to tune priority of CPTS kthread_worker thread on -RT
(thread name "cpts").
Hence, the CPTS driver is converted to use PTP auxiliary worker as PHC
subsystem implements such functionality in a generic way now.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Push the request_irq function to the end of probe so as
to ensure all the required fields are populated in the event
of an ISR getting executed right after requesting the irq.
Currently while loading the crash kernel a crash was seen as
soon as devm_request_threaded_irq was called. This was due to
n->poll being NULL which is called as part of net_rx_action
function.
Suggested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is cpts function to check if packet can be timstamped with cpts.
Seems that ptp_classify_raw cover all cases listed with "case".
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpts can timestmap only ptp packets at this moment, so driver
cannot mark every packet as though it's going to be timestamped,
only because h/w timestamping for given skb is enabled with
SKBTX_HW_TSTAMP. It doesn't allow to use sw timestamping, as result
outgoing packet is not timestamped at all if it's not PTP and h/w
timestamping is enabled. So, fix it by setting SKBTX_IN_PROGRESS
only for PTP packets.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move sw timestamp function close to channel submit function.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
cpsw driver tries to get macid for am43xx SoCs using the compatible
ti,am4372. But not all variants of am43x uses this complatible like
epos evm uses ti,am438x. So use a generic compatible ti,am43 to get
macid for all am43 based platforms.
Reviewed-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make return value void since function never return meaningfull value
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW driver does not handle this interrupt, so there are no reasons to enable
it in hardware.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW driver supports PTP v1 messages, but for unknown reasons this filter
is not advertised. As result,
./tools/testing/selftests/networking/timestamping/timestamping utility
can't be used for testing of CPSW RX timestamping with option
SOF_TIMESTAMPING_RX_HARDWARE, because it uses
HWTSTAMP_FILTER_PTP_V1_L4_SYNC filter.
Hence, fix it by advertising HWTSTAMP_FILTER_PTP_V1_L4_XXX filters
in CPSW driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to push the chain index down to the drivers, so they have the
information to which chain the rule belongs. For now, no driver supports
multichain offload, so only chain 0 is supported. This is needed to
prevent chain squashes during offload for now. Later this will be used
to implement multichain offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include HWTSTAMP_FILTER_NTP_ALL in net_hwtstamp_validate() as a valid
filter and update drivers which can timestamp all packets, or which
explicitly list unsupported filters instead of using a default case, to
handle the filter.
CC: Richard Cochran <richardcochran@gmail.com>
CC: Willem de Bruijn <willemb@google.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver doesn't support timestamping of all received packets and
should return error when trying to enable the HWTSTAMP_FILTER_ALL
filter.
Cc: WingMan Kwok <w-kwok2@ti.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix error path while dma open channel issue. Also, no need to check output
on NULL if it's never returned.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When users set flow control using ethtool the bits are set properly in the
CPGMAC_SL MACCONTROL register, but the FIFO depth in the respective Port n
Maximum FIFO Blocks (Pn_MAX_BLKS) registers remains set to the minimum size
reset value. When receive flow control is enabled on a port, the port's
associated FIFO block allocation must be adjusted. The port RX allocation
must increase to accommodate the flow control runout. The TRM recommends
numbers of 5 or 6.
Hence, apply required Port FIFO configuration to
Pn_MAX_BLKS.Pn_TX_MAX_BLKS=0xF and Pn_MAX_BLKS.Pn_RX_MAX_BLKS=0x5 during
interface initialization.
Cc: Schuyler Patton <spatton@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
Tony Lindgren reports a kernel oops that resulted from my compile-time
fix on the default config. This shows two problems:
a) configurations that did not already enable PTP_1588_CLOCK will
now miss the cpts driver
b) when cpts support is disabled, the driver crashes. This is a
preexisting problem that we did not notice before my patch.
While the second problem is still being investigated, this modifies
the dependencies again, getting us back to the original state, with
another 'select NET_PTP_CLASSIFY' added in to avoid the original
link error we got, and the 'depends on POSIX_TIMERS' to hide
the CPTS support when turning it on would be useless.
Cc: stable@vger.kernel.org # 4.11 needs this
Fixes: 07fef36234 ("cpsw/netcp: cpts depends on posix_timers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is unused and probably was unintentionally left while
moving completion queue mapping in submit function.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_err message and rejoin
line.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly simple cases of overlapping changes (adding code nearby,
a function whose name changes, for example).
Signed-off-by: David S. Miller <davem@davemloft.net>
TI's cpsw driver handles both OF and non-OF case for phy
connect. Unfortunately of_phy_connect() returns NULL on
error while phy_connect() returns ERR_PTR().
To handle this, cpsw_slave_open() overrides the return value
from phy_connect() to make it NULL or error.
This leaves a small window, where cpsw_adjust_link() may be
invoked for a slave while slave->phy pointer is temporarily
set to -ENODEV (or some other error) before it is finally set
to NULL.
_cpsw_adjust_link() only handles the NULL case, and an oops
results when ERR_PTR() is seen by it.
Note that cpsw_adjust_link() checks PHY status for each
slave whenever it is invoked. It can so happen that even
though phy_connect() for a given slave returns error,
_cpsw_adjust_link() is still called for that slave because
the link status of another slave changed.
Fix this by using a temporary pointer to store return value
of {of_}phy_connect() and do a one-time write to slave->phy.
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case, if TX watchdog is fired some or all netdev TX queues will be
stopped and as part of recovery it is required not only to drain and
reinitailize CPSW TX channeles, but also wake up stoppted TX queues what
doesn't happen now and netdevice will stop transmiting data until
reopenned.
Hence, add netif_tx_wake_all_queues() call in .ndo_tx_timeout() to complete
recovery and restore TX path.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/genet/bcmmii.c
drivers/net/hyperv/netvsc.c
kernel/bpf/hashtab.c
Almost entirely overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
With posix timers having become optional, we get a build error with
the cpts time sync option of the CPSW driver:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_find_ts':
drivers/net/ethernet/ti/cpts.c:291:23: error: implicit declaration of function 'ptp_classify_raw';did you mean 'ptp_classifier_init'? [-Werror=implicit-function-declaration]
This adds a hard dependency on PTP_CLOCK to avoid the problem, as
building it without PTP support makes no sense anyway.
Fixes: baa73d9e47 ("posix-timers: Make them configurable")
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dependency is reversed: cpsw and netcp call into cpts,
but cpts depends on the other two in Kconfig. This can lead
to cpts being a loadable module and its callers built-in:
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_remove':
cpsw.c:(.text.cpsw_remove+0xd0): undefined reference to `cpts_release'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_rx_handler':
cpsw.c:(.text.cpsw_rx_handler+0x2dc): undefined reference to `cpts_rx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_tx_handler':
cpsw.c:(.text.cpsw_tx_handler+0x7c): undefined reference to `cpts_tx_timestamp'
drivers/net/ethernet/ti/cpsw.o: In function `cpsw_ndo_stop':
As a workaround, I'm introducing another Kconfig symbol to
control the compilation of cpts, while making the actual
module controlled by a silent symbol that is =y when necessary.
Fixes: 6246168b4a ("net: ethernet: ti: netcp: add support of cpts")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.
This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.
Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ale is a property of cpsw, so change dev to cpsw->dev,
aka pdev->dev, to be consistent.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage count function is based on ndev_running flag that is
updated before calling ndo_open/close, but if ndo is called in
another place, as with suspend/resume, the counter is not changed,
that breaks sus/resume. For common resource no difference which
device is using it, does matter only device count. So, replace
usage count function on var and inc and dec it in ndo_open/close.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a copy-paste error, which hides breaking of resume
for CPSW driver: there was replaced netdev_priv() to ndev_to_cpsw(ndev)
in suspend, but left it unchanged in resume.
Fixes: 606f399395
(ti: cpsw: move platform data and slaves info to cpsw_common)
Reported-by: Alexey Starikovskiy <AStarikovskiy@topcon.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If skb_padto failed the skb has been dropped already, so it was
consumed, but it doesn't mean it was sent, thus no need to update
queue tx time, etc. So, return NET_XMIT_DROP as more appropriate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to update jiffies in txq->trans_start twice and only for tx 0,
it's supposed to be done in netdev_start_xmit() and per tx queue.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as off
811a919135 ("phy state machine: failsafe leave invalid RUNNING state")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to update jiffies in txq->trans_start twice, it's supposed to be
done in netdev_start_xmit() and anyway is re-written. Also, no reason to
update trans time in case of an error.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In switch mode on struct cpsw_slave->ndev field will be initialized with
proper value only for the one cpsw slave port, as result
cpsw_get_usage_count() will generate "Unable to handle kernel NULL pointer
dereference" exception when first ethernet interface is opening
cpsw_ndo_open(). This issue causes boot regression on AM335x EVM and
reproducible on am57xx-evm (switch mode).
Fix it by adding additional check for !cpsw->slaves[i].ndev in
cpsw_get_usage_count().
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Fixes: 03fd01ad0e ("net: ethernet: ti: cpsw: don't duplicate ndev_running")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding cpsw_set_ringparam ethtool op, better to carry out
common parts of similar ops splitting descriptors in runtime. It
allows to reuse these parts and shows what the ops actually do.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to duplicate the same function in rx handler to get info
if any interface is running.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to create additional vars to identify if interface is running.
So simplify code by removing redundant var and checking usage counter
instead.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to disable interrupts if no open devices,
they are disabled anyway.
Even no need to disable interrupts if some ndev is opened, In this
case shared resources are not touched, only parameters of ndev shell,
so no reason to disable them also. Removed lines have proved it.
So, no need in redundant check and interrupt disable.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Common res usage is possible only in case an interface is
running. In case of not dual emac here can be only one interface,
so while ndo_open and switch mode, only one interface can be opened,
thus if open is called no any interface is running ... and no common
res are used. So remove check on dual emac, it will simplify
code/understanding and will match the name it's called.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check "ch" on NULL first, then get ctlr.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The #warning was present 10 years ago when the driver first got merged.
As the platform is rather obsolete by now, it seems very unlikely that
the warning will cause anyone to fix the code properly.
kernelci.org reports the warning for every build in the meantime, so
I think it's better to just turn it into a code comment to reduce
noise.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit: bc1f44709c - net: make ndo_get_stats64 a void function
and
Commit: 6a8162e99e - net: netcp: store network statistics in 64 bits.
The commit 6a8162e99e adds ndo_get_stats64 function as per old
signature which causes compilation error:
drivers/net/ethernet/ti/netcp_core.c:1951:28: error:
initialization from incompatible pointer type
.ndo_get_stats64 = netcp_get_stats,
Hence correct netcp_get_stats function signature as per
the latest definition.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Fixes: 6a8162e99e ("net: netcp: store network statistics in 64 bits")
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow to set number of descs close to possible values. In case of
minimum limit it's equal to number of channels to be able to set
at least one desc per channel. For maximum limit leave enough descs
number for tx channels.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NetCP NU Switch ALE, some of the mask bits are different than
defaults used in the driver. Add a new macro DEFINE_ALE_FIELD1 that use
a configurable mask bits and use it in the driver. These bits are set to
correct values by using the new variables added to cpsw_ale structure
and re-used in the macros. The parameter nu_switch_ale is configured by
the caller driver to indicate the ALE is for that switch and is used in
the ALE driver to do customization as needed.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ALE h/w on newer version of NetCP (K2E/L/G) does provide a ALE_STATUS
register for the size of the ALE Table implemented in h/w. Currently
for example we set ALE Table size to 1024 for NetCP ALE on
K2E even though the ALE Status/Documentation shows it has 8192 entries.
So take advantage of this register to read the size of ALE table supported
and use that value in the driver for the newer version of NetCP ALE.
For NetCP lite, ALE Table size is much less (64) and indicated by a size
of zero in ALE_STATUS. So use that as a default for now. While at it,
also fix the ale table size on 10G switch to 2048 per User guide
http://www.ti.com/lit/ug/spruhj5/spruhj5.pdf
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In NU Ethernet switch used on some of the Keystone SoCs, there is
separate UNKNOWNVLAN register for membership, unreg mcast flood, reg
mcast flood and force untag egress bits in ALE. So control for these
fields require different address offset, shift and size of field.
As this ALE has the same version number as ALE in CPSW found on other
SoCs, customization based on version number is not possible. So
use a configuration parameter, nu_switch_ale, to identify the ALE
ALE found in NU Switch. Different treatment is needed for NU Switch
ALE due to difference in the ale table bits, separate unknown vlan
registers etc. The register information available in ale_controls,
needs to be updated to support the netcp NU switch h/w. So it is not
constant array any more since it needs to be updated based
on ALE type. The header of the file is also updated to indicate it
supports N port switch ALE, not just 3 port. The version mask is
3 bits in NU Switch ALE vs 8 bits on other ALE types.
While at it, change the debug print to info print so that ALE
version gets displayed in boot log.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the newer Ethernet switch hw (such as that on k2e/l/g) can
strip the Etherenet FCS from packet at the port 0 egress of the switch.
So use this capability instead of doing it in software.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently to parse phy-handle, driver doesn't check if the interface is
MAC to PHY. This patch add this check for all MAC to PHY interface types
supported by the driver.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the network statistics were stored in 32 bit variable
which can cause some stats to roll over after several minutes of
high traffic. This implements 64 bit storage so larger numbers
can be stored.
Signed-off-by: Michael Scherban <m-scherban@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The psdata is populated with command data by netcp modules
to the tail of the buffer and set_words() copy the same
to the front of the psdata. So remove the redundant memmov
function call.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the eflag bits from the received desc and pass it down
the rx_hook chain to be available for netcp modules. Also the
psdata and epib data has to be inspected by the netcp modules.
So the desc can be freed only after returning from the rx_hook.
So move knav_pool_desc_put() after the rx_hook processing.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPDMA uses one pool of descriptors for both RX and TX which by default
split between all channels proportionally depending on total number of
CPDMA channels and number of TX and RX channels. As result, more
descriptors will be consumed by TX path if there are more TX channels and
there is no way now to dedicate more descriptors for RX path.
So, add the ability to re-split CPDMA pool of descriptors between RX and TX
path via ethtool '-G' command wich will allow to configure and fix number
of descriptors used by RX and TX path, which, then, will be split between
RX/TX channels proportionally depending on RX/TX channels number and
weight. ethtool '-G' command will accept only number of RX entries and rest
of descriptors will be arranged for TX automatically.
Command:
ethtool -G <devname> rx <number of descriptors>
defaults and limitations:
- minimum number of rx descriptors is 10% of total number of descriptors in
CPDMA pool
- maximum number of rx descriptors is 90% of total number of descriptors in
CPDMA pool
- by default, descriptors will be split equally between RX/TX path
- any values passed in "tx" parameter will be ignored
Usage:
# ethtool -g eth0
Pre-set maximums:
RX: 7372
RX Mini: 0
RX Jumbo: 0
TX: 0
Current hardware settings:
RX: 4096
RX Mini: 0
RX Jumbo: 0
TX: 4096
# ethtool -G eth0 rx 7372
# ethtool -g eth0
Ring parameters for eth0:
Pre-set maximums:
RX: 7372
RX Mini: 0
RX Jumbo: 0
TX: 0
Current hardware settings:
RX: 7372
RX Mini: 0
RX Jumbo: 0
TX: 820
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW CPDMA can process buffer descriptors placed as in internal
CPPI RAM as in DDR. This patch adds support in CPSW and CPDMA for
descs_pool_size mudule parameter, which defines total number of CPDMA CPPI
descriptors to be used for both ingress/egress packets processing:
- memory size, required for CPDMA descriptor pool, is calculated basing
on number of descriptors specified by user in descs_pool_size and
CPDMA descriptor size and allocated from coherent memory (CMA area);
- CPDMA descriptor pool will be allocated in DDR if pool memory size >
internal CPPI RAM or use internal CPPI RAM otherwise;
- if descs_pool_size not specified in DT - the default value 256 will
be used which will allow to place CPDMA descriptors pool into the
internal CPPI RAM (current default behaviour);
- CPDMA will ignore descs_pool_size if descs_pool_size = 0 for
backward comaptiobility with davinci_emac.
descs_pool_size is boot time setting and can't be changed once
CPSW/CPDMA is initialized.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_ioremap() and simplify the code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update cpdma_desc_pool_create/destroy() to accept only one parameter
struct cpdma_ctlr*, as this structure contains all required
information for pool creation/destruction.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The currently processing cpdma descriptor with EOQ flag set may
contain two values in Next Descriptor Pointer field:
- valid pointer: means CPDMA missed addition of new desc in queue;
- null: no more descriptors in queue.
In the later case, it's not required to write to HDP register, but now
CPDMA does it.
Hence, add additional check for Next Descriptor Pointer != null in
cpdma_chan_process() function before writing in HDP register.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's observed that cpsw/cpdma is not working properly when CPPI
descriptors are placed in DDR instead of internal CPPI RAM on am437x
SoC:
- rx/tx silently stops processing packets;
- or - after boot it's working for sometime, but stuck once Network
load is increased (ping is working, but iperf is not).
(The same issue has not been reproduced on am335x and am57xx).
It seems that write to HDP register processed faster by interconnect
than writing of descriptor memory buffer in DDR, which is probably
caused by store buffer / write buffer differences as these functions
are implemented differently across devices. So, to fix this i come up
with two minimal, required changes:
1) all accesses to the channel register HDP/CP/RXFREE registers should
be done using sync IO accessors readl()/writel(), because all previous
memory writes writes have to be completed before starting channel
(write to HDP) or completing desc processing.
2) the change 1 only doesn't work on am437x and additional reading of
desc's field is required right after the new descriptor was filled
with data and before pointer on it will be stored in
prev_desc->hw_next field or HDP register.
In addition, to above changes this patch eliminates all relaxed ordering
I/O accessors in this driver as suggested by David Miller to avoid such
kind of issues in the future, but with one exception - relaxed IO accessors
will still be used to fill desc in cpdma_chan_submit(), which is safe as
there is read barrier at the end of write sequence, and because sync IO
accessors usage here will affect on net performance.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
This patch adds the missing 10gbe host port tx priority map
configurations.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ethtool ops, it needs to retrieve the corresponding
ethss module (gbe or xgbe) from the net_device structure.
Prior to this patch, the retrieving procedure only
checks for the gbe module. This patch fixes the issue
by checking the xgbe module if the net_device structure
does not correspond to the gbe module.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
This patch adds support of the cpts device found in the
gbe and 10gbe ethernet switches on the keystone 2 SoCs
(66AK2E/L/Hx, 66AK2Gx).
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The channels are common for both ndevs in dual emac mode. Hence, keep
in sync their rates.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't re-split res in the following cases:
- speed of phys is not changed
- speed of phys is changed and no rate limited channels
- speed of phys is changed and all channels are rate limited
- phy is unlinked while dev is open
- phy is linked back but speed is not changed
The maximum speed is sum of "linked" phys, thus res are split taken
in account two interfaces, both for dual emac mode and for
switch mode.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-split weight along with budget. It simplify code a little
and update state after every rate change. Also it's necessarily
to move arguments checks to this combined function. Replace
maximum rate check for an interface on maximum possible rate.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to start queues after cpsw is started as it will be done
while cpsw_adjust_link(), after phy connection.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the same, more convenient macros, to get active slave.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI CPMAC driver calls into PHYLIB which now checks for
net_device->dev.parent, so make sure we do set it before calling into
any MDIO/PHYLIB related function.
Fixes: ec988ad78e ("phy: Don't increment MDIO bus refcount unless it's a different owner")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for setting the RGMII_IDMODE bit was added in the commit
referenced below. However, that commit did not add the symmetrical
clearing of the bit by way of setting it in "mask". Add it here.
Note that the documentation marks clearing this bit as "reserved",
however, according to TI, support for delaying the clock does exist in
the MAC, although it is not officially supported.
We tested this on a board with an RGMII to RGMII link that will not
work unless this bit is cleared.
Fixes: 0fb26c3063 ("drivers: net: cpsw-phy-sel: add support to configure rgmii internal delay")
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPTS drivers uses 8sec period for overflow checking with
assumption that CPTS retclk will not exceed 500MHz. But that's not
true on some TI platforms (Kesytone 2). As result, it is possible that
CPTS counter will overflow more than once between two readings.
Hence, fix it by selecting overflow check period dynamically as
max_sec_before_overflow/2, where
max_sec_before_overflow = max_counter_val / rftclk_freq.
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
