Add print of the following values on init:
1. ieee vendor id
2. sandbox product id
3. sandbox product version
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Adi Nissim <adin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Add device name for Mellanox FPGA devices.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Adi Nissim <adin@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
So far, the PCI BAR0 register is used for triggering FW reset. However,
that is a legacy attitude and it is recommended to use MRSR to perform
reset instead. So do that. Move the reset into init() function as
the cmd interface needs to be used. With that, IRQ initialization needs
to be moved as well. As a side effect, the reset move simplifies
the devlink reload flow.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an exception in command interface processing in case the MRSR
register is written to. The register triggers FW reset and during the
reset FW returns an error. So handle this by ignoring this error while
writing to MRSR register.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "net: qcom/emac: Encapsulate sgmii ops under one structure"
introduced the sgmii_ops structure, but did not correctly initialize
it on device tree platforms. This resulted in compiler warnings when
ACPI is not enabled.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
With CONFIG_TLS=m and MLX5_CORE_EN=y, we get a link failure:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/tls_rxtx.o: In function `mlx5e_tls_handle_ooo':
tls_rxtx.c:(.text+0x24c): undefined reference to `tls_get_record'
drivers/net/ethernet/mellanox/mlx5/core/en_accel/tls_rxtx.o: In function `mlx5e_tls_handle_tx_skb':
tls_rxtx.c:(.text+0x9a8): undefined reference to `tls_device_sk_destruct'
This narrows down the dependency to only allow the configurations
that will actually work. The existing dependency on TLS_DEVICE is
not sufficient here since MLX5_EN_TLS is a 'bool' symbol.
Fixes: c83294b9ef ("net/mlx5e: TLS, Add Innova TLS TX support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Acked-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report the stat diff to make sure MQ stats add up to child stats.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for MQ offload and setting RED parameters
on queue-by-queue basis.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate the PF representor as multi-queue to allow setting
the configuration per-queue.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a handful of statistics exposing some internal details
of the implementation. Expose those via ethtool.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow nfp apps to add extra ethtool stats.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report basic and extended RED statistics back to TC.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Offload simple RED configurations. For now support only DCTCP
like scenarios where min and max are the same.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Queue levels for simple ECN marking are stored in _abi_nfd_out_q_lvls_X
symbol, where X is the PCIe PF id. Find out the location of that symbol
and add helpers for modifying it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ABM NIC FW has a cut-through mode where the PCIe queuing
is bypassed, thus working like our standard NIC FWs. Use this
mode by default and only enable queuing in switchdev mode where
users can configure it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers are using a bare number inside phys_port_name
as VF id and OpenStack's regexps will pick it up. We can't
use a bare number for your vNICs, prefix the names with 'n'.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent change we started returning 0 from
ndo_get_phys_port_name for VFs. The name parameter for
ndo_get_phys_port_name is not initialized by the stack so
this can lead to a crash. We should have kept returning
-EOPNOTSUPP in the first place.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series includes updates for mlx5e netdev driver.
1) Allowr flow based VF vport mirroring under sriov switchdev scheme,
added support for offloading the TC mirred mirror sub-action, from
Chris Mi.
=================
From: Or Gerlitz <ogerlitz@mellanox.com>
The user will typically set the actions order such that the mirror
port (mirror VF) sees packets as the original port (VF under
mirroring) sent them or as it will receive them. In the general case,
it means that packets are potentially sent to the mirror port before
or after some actions were applied on them.
To properly do that, we follow on the exact action order as set for
the flow and make sure this will also be the case when we program the
HW offload.
If all the actions should apply before forwarding to the mirror and dest port,
mirroring is just multicasting to the two vports. Otherwise, we split
the TC flow to two HW rules, where the 1st applies only the actions
needed up to the mirror (if there are such) and the 2nd the rest of
the actions plus the forwarding to the dest vport.
=================
2) Move to order-0 only allocations (using fragmented work queues) for all
work queues used by the driver, RX and TX descriptor rings
(RQs, SQs and Completion Queues (CQs)), from Tariq Toukan.
3) Avoid resetting netdevice statistics on netdevice
state changes, from Eran Ben Elisha.
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJbCKCcAAoJEEg/ir3gV/o++7sH/1FPmwvpf4qNEsusr714lNnl
PxzVjnwxKZNYyovIjr6QGSxMM1qDiPejyYnZIAzH00B+XWCq3zn8H3sfJLFbmxN3
clayd6dGV27HzLZwV2aD9vXfVb7snNhQtTp5zoajsnZY4xO335n3FA3kF5TxLqKO
bxsnY2xSaSpbrBH2z2UvHc+ib9KnvY1Q+gr2WqdRnN5Tm51Zq+bgaUw0nROefGJK
XR/aVBub3PsjA8W/0/b3DGfiP1bgPeU6QmLhdjn3IEufFtbEJH+K/4u53l3A4RLR
fXmJrWKlZn8j7LUBFOD0/G43RU/YzqRgwF/iUwCxbUU2wK/J0cPv23drLDVYzaY=
=n7Zz
-----END PGP SIGNATURE-----
Merge tag 'mlx5e-updates-2018-05-25' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5e-updates-2018-05-25
This series includes updates for mlx5e netdev driver.
1) Allowr flow based VF vport mirroring under sriov switchdev scheme,
added support for offloading the TC mirred mirror sub-action, from
Chris Mi.
=================
From: Or Gerlitz <ogerlitz@mellanox.com>
The user will typically set the actions order such that the mirror
port (mirror VF) sees packets as the original port (VF under
mirroring) sent them or as it will receive them. In the general case,
it means that packets are potentially sent to the mirror port before
or after some actions were applied on them.
To properly do that, we follow on the exact action order as set for
the flow and make sure this will also be the case when we program the
HW offload.
If all the actions should apply before forwarding to the mirror and dest port,
mirroring is just multicasting to the two vports. Otherwise, we split
the TC flow to two HW rules, where the 1st applies only the actions
needed up to the mirror (if there are such) and the 2nd the rest of
the actions plus the forwarding to the dest vport.
=================
2) Move to order-0 only allocations (using fragmented work queues) for all
work queues used by the driver, RX and TX descriptor rings
(RQs, SQs and Completion Queues (CQs)), from Tariq Toukan.
3) Avoid resetting netdevice statistics on netdevice
state changes, from Eran Ben Elisha.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When register a RoCE client with hnae3vf device, it needs to judge
the device whether support RoCE vf function. Otherwise, it will
lead to calltrace when RoCE is not support vf function and remove
roce device.
The calltrace as follows:
[ 93.156614] Unable to handle kernel NULL pointer dereference at virtual address 00000015
<SNIP>
[ 93.278784] Call trace:
[ 93.278788] hnae3_match_n_instantiate+0x24/0xd8 [hnae3]
[ 93.278790] hnae3_register_client+0xcc/0x150 [hnae3]
[ 93.278801] hns_roce_hw_v2_init+0x18/0x1000 [hns_roce_hw_v2]
[ 93.278805] do_one_initcall+0x58/0x160
[ 93.278807] do_init_module+0x64/0x1d8
[ 93.278809] load_module+0x135c/0x15c8
[ 93.278811] SyS_finit_module+0x100/0x118
[ 93.278816] __sys_trace_return+0x0/0x4
[ 93.278827] Code: aa0003f5 12001c56 aa1e03e0 d503201f (b9402660)
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Reported-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reported-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware now supports control of all leds. Existing HNS3 driver code
only supported led locate command over SFP Fibre ports. But now it
is also supported over copper port.
This patch removes existing not needed code for the led locate
command and updates the led control command between driver and
firmware.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous implementation of led control for fibre port , parses the
port speed configuration, checks the link status and traffic status per
second, and updates the blink status of link led, traffic led and speed
led.
Now, the firmware takes responsibility to handle the led, the dirver just
needs to deal with locate command.
So the codes for link led, traffic led and speed led are useless now. This
patch removes these redundant codes.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we down the port, some packets are left in TX/RX buffer. When we
up the port again, these old packets are forwarded to protocol stack
or are sent to internet. It will make some problem. TX/RX buffer should
be cleared when stopping port. This patch adds some function to ensure
the buffer is clean when port is started. We should clear the rings
when clients are being un-initialized as well.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our code will ensure that hns3_clear_tx_ring is not used to cleared
RX rings and hns3_clear_rx_ring is not used to cleared TX rings. So
the ring type check is unnecessary.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX Buffer Descriptor contains a VALID bit which indicates if the BD
is valid and has some data. This field is set by HNS3 hardware to
intimate the driver of some valid data present in the BD. nd should
be reset by the driver when BD is being used again. In the existing
code this bit was not being (re-)initialized properly and hence was
causing problems.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNAE3 module supports kernel nic driver, user nic driver and roce driver,
and there are 3 client types. Driver uses one bit(HNAE3_CLIENT_INITED_B)
to indicate the client initialization state, it will cause confusion
for 3 client types. This patch fixes it by use 3 bits to indicate the
initialization state.
Fixes: 38caee9d3e ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before the firmware updates the crq's tail pointer, if the PF driver
reads the data in the crq, the data may be incomplete at this time,
which will lead to the driver read an unknown message.
This patch fixes it by checking if crq is not empty before reading the
message.
Fixes: c1a81619d7 ("net: hns3: Add mailbox interrupt handling to PF driver")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HCLGE_PROMISC_TX_EN_B and HCLGE_PROMISC_RX_EN_B are not supported
on pdev revision(0x20), new revision(0x21) supports them.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware Revision(0x21) Buffer Descriptor adds a field STRP_TAGP
for vlan stripped processed indication. STRP_TAGP field has 2 bits,
bit 0 is stripped indication of the vlan tag in outer vlan tag
field, bit 1 is stripped indication of the vlan tag in inner vlan
tag field. For each bit, 0 indicates the tag is not stripped and
1 indicates the tag is stripped.
This patch adds STRP_TAGP support for revision(0x21), and does not
change the revision(0x20) action.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HNS3 Hardware can support up to two VLAN tags in transmit leg, the PPP
module can handle the packets based on the tag1 and tag2 config. This
patch adds support for tag2 config for vlan handling
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the latest revision of the hardware, if a packet is spanning
across multiple BDs then only VLD bit and current data size info
is valid in each BD, and rest of the information is only valid
in the last BD of the packet. In such case we should make sure
we are fetching RX packet size from the first descriptor and
information like VLAN should be fetched from last BD.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manage dwmac-4.20a version from synopsys
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Glue codes to support stm32mp157c device and stay
compatible with stm32 mcu familly
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Global variable gfar_phc_index was used to get and store
phc index through gianfar_ptp driver. However gianfar_ptp
had been renamed as ptp_qoriq for QorIQ common PTP driver.
This gfar_phc_index doesn't work any more, and the phc index
is stored in drvdata now. This patch is to support getting
phc index through ptp_qoriq drvdata.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gianfar_ptp was the PTP clock driver for 1588 timer
module of Freescale QorIQ eTSEC (Enhanced Three-Speed
Ethernet Controllers) platforms. Actually QorIQ DPAA
(Data Path Acceleration Architecture) platforms is
also using the same 1588 timer module in hardware.
This patch is to rework gianfar_ptp as QorIQ common
PTP driver to support both DPAA and eTSEC. Moved
gianfar_ptp.c to drivers/ptp/, renamed it as
ptp_qoriq.c, and renamed many variables. There were
not any function changes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers, such as DWC EQOS on Tegra, need to perform operations that
can sleep under this lock (clk_set_rate() in tegra_eqos_fix_speed()) for
proper operation. Since there is no need for this lock to be a spinlock,
convert it to a mutex instead.
Fixes: e6ea2d16fc ("net: stmmac: dwc-qos: Add Tegra186 support")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx-timeout mostly happens due to some issue in the device. In such cases,
debug dump would be helpful for identifying the cause of the issue.
This patch adds support to spill debug data during the Tx timeout. Here
bnx2x_panic_dump() API is used instead of bnx2x_panic(), since we still
want to allow the Tx-timeout recovery a chance to succeed.
Changes from previous version:
-------------------------------
v2: Fixed a coding error.
Please consider applying this to "net-next".
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all RQ, SQ and channel counters from the channel objects into the
priv structure. With this change, counters will not be reset upon
channel configuration changes.
Channel's statistics for SQs which are associated with TCs higher than
zero will be presented in ethtool -S, only for SQs which were opened at
least once since the module was loaded (regardless of their open/close
current status). This is done in order to decrease the total amount of
statistics presented and calculated for the common out of box use (no
QoS).
mlx5e_channel_stats is a compound of CH,RQ,SQs stats in order to
create locality for the NAPI when handling TX and RX of the same
channel.
Align the new statistics struct per ring to avoid several channels
update to the same cache line at the same time.
Packet rate was tested, no degradation sensed.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
CC: Qing Huang <qing.huang@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Introduce a new read/write lock that will protect statistics gathering from
netdev channels configuration changes.
e.g. when channels are being replaced (increase/decrease number of rings)
prevent statistic gathering (ndo_get_stats64) to read the statistics of
in-active channels (channels that are being closed).
Plus update channels software statistics on the fly when calling
ndo_get_stats64, and remove it from stats periodic work.
Fixes: 9218b44dcc ("net/mlx5e: Statistics handling refactoring")
Signed-off-by: Shalom Lagziel <shaloml@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
PHY link down events counter belongs to phy_counters group.
although it has special handling, it doesn't mean it can't be there.
Move it to phy_counters_grp handler.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Complete the transition of all WQ types to use fragmented
order-0 coherent memory instead of high-order allocations.
CQ-WQ already uses order-0.
Here we do the same for cyclic and linked-list WQs.
This allows the driver to load cleanly on systems with a highly
fragmented coherent memory.
Performance tests:
ConnectX-5 100Gbps, CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Packet rate of 64B packets, single transmit ring, size 8K.
No degradation is sensed.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If CONFIG_MLX5_CORE_IPOIB is not set, compile-out the
IPOIB related headers.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We fill SQ edge with NOPs to avoid WQEs wrap.
Here, instead of doing that in advance for the maximum possible
WQE size, we do it on-demand using the actual WQE size.
We re-order some parts in mlx5e_sq_xmit to finish the calculation
of WQE size (ds_cnt) before doing any writes to the WQE buffer.
When SQ work queue is fragmented (introduced in an downstream patch),
dealing with WQE wraps becomes more frequent. This change would drastically
reduce the overhead in this case.
Performance tests:
ConnectX-5 100Gbps, CPU: Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Packet rate of 64B packets, single transmit ring, size 8K.
Before: 14.9 Mpps
After: 15.8 Mpps
Improvement of 6%.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use the WQ API to get the WQ size, and to map a counter
into a WQ entry index.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If a TC rule needs to be split for mirroring, create two HW rules,
in the first level and the second level flow tables accordingly.
In the first level flow table, forward the packet to the mirror
port and forward the packet to the second level flow table for
further processing, eg. encap, vlan push or header re-write.
Currently the matching is repeated in both stages.
While here, simplify the setup of the vhca id valid indicator also
in the existing code.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, we only support the mirred redirect TC sub-action. In order
to support flow based vport mirroring, add support to parse the mirred
mirror sub-action.
For mirroring, user-space will typically set the action order such that
the mirror port (mirror VF) sees packets as the original port (VF under
mirroring) sent them or as it will receive them.
In the general case, it means that packets are potentially sent to the
mirror port before or after some actions were applied on them. To
properly do that, we should follow on the exact action order as set for
the flow and make sure this will also be the case when we program the HW
offload.
We introduce a counter for the output ports (attr->out_count), which we
increase when parsing each mirred redirect/mirror sub-action and when
dealing with encap.
We introduce a counter (attr->mirror_count) telling us if split is
needed. If no split is needed and mirroring is just multicasting to
vport, the mirror count is zero, all the actions of the TC flow should
apply on that single HW flow.
If split is needed, the mirror count tells where to do the split, all
non-mirred tc actions should apply only after the split.
The mirror count is set while parsing the following actions encap/decap,
header re-write, vlan push/pop.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If firmware supports the forward action with a destination list
that includes a flow table, create a second level FDB flow table.
This is going to be used for flow based mirroring under the switchdev
offloads mode.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
We have several fdb flow tables for each of the legacy and switchdev
modes. In the switchdev mode, there are fast path and slow path flow
tables. Towards adding more flow tables in upcoming patches, reorganize
and rename the various existing ones to reflect their functionality.
Signed-off-by: Chris Mi <chrism@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
