Combine the near identical implementations of intel_logical_ring_begin()
and intel_ring_begin() - the only difference is that the logical wait
has to check for a matching ring (which is assumed by legacy).
In the process some debug messages are culled as there were following a
WARN if we hit an actual error.
v2: Updated commentary
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-12-git-send-email-chris@chris-wilson.co.uk
The code to switch_mm() is already handled by i915_switch_context(), the
only difference required to setup the aliasing ppgtt is that we need to
emit te switch_mm() on the first context, i.e. when transitioning from
engine->last_context == NULL. This allows us to defer the
initialisation of the GPU from early device initialisation to first use,
which should marginally speed up both. The caveat is that we then defer
the context initialisation until first use - i.e. we cannot assume that
the GPU engines are initialised. For example, this means that power
contexts for rc6 (Ironlake) need to explicitly loaded, as they are.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-11-git-send-email-chris@chris-wilson.co.uk
Since we do the l3-remap on context switch, we can remove the redundant
early call to set the mapping prior to performing the first context
switch.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-10-git-send-email-chris@chris-wilson.co.uk
We can use a single MI_LOAD_REGISTER_IMM command packet to write all the
L3 remapping registers, shrinking the number of bytes required to emit
the context switch.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-9-git-send-email-chris@chris-wilson.co.uk
In order to force a reload of the context image upon resume, we first
need to mark its absence on suspend. Currently we are failing to restore
the golden context state and any context w/a to the default context
after resume.
One oversight corrected, is that we had forgotten to reapply the L3
remapping when restoring the lost default context.
v2: Remove deprecated WARN.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-7-git-send-email-chris@chris-wilson.co.uk
Similarly to i915_gem_object_pin_map on LLC platforms, we can
use the new VMA based io mapping on !LLC to amoritize the cost
of ringbuffer pinning and unpinning.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-6-git-send-email-chris@chris-wilson.co.uk
By tracking the iomapping on the VMA itself, we can share that area
between multiple users. Also by only revoking the iomapping upon
unbinding from the mappable portion of the GGTT, we can keep that iomap
across multiple invocations (e.g. execlists context pinning).
Note that by moving the iounnmap tracking to the VMA, we actually end up
fixing a leak of the iomapping in intel_fbdev.
v1.5: Rebase prompted by Tvrtko
v2: Drop dev_priv parameter, we can recover the i915_ggtt from the vma.
v3: Move handling of ioremap space exhaustion to vmap_purge and also
allow vmallocs to recover old iomaps. Add Tvrtko's kerneldoc.
v4: Fix a use-after-free in shrinker and rearrange i915_vma_iomap
v5: Back to i915_vm_to_ggtt
v6: Use i915_vma_pin_iomap and i915_vma_unpin_iomap to mark critical
sections and ensure the VMA cannot be reaped whilst mapped.
v7: Move i915_vma_iounmap so that consumers of the API are not tempted,
and add iomem annotations
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-5-git-send-email-chris@chris-wilson.co.uk
In a couple of places, we have an i915_address_space that we know is
really an i915_ggtt that we want to use. Create an inline helper to
convert from the i915_address_space subclass into its container.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-4-git-send-email-chris@chris-wilson.co.uk
The ioremap() hidden behind the io_mapping_map_wc() convenience helper
can be used for remapping multiple pages. Extend the helper so that
future callers can use it for larger ranges.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Yishai Hadas <yishaih@mellanox.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: "Peter Zijlstra (Intel)" <peterz@infradead.org>
Cc: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: Luis R. Rodriguez <mcgrof@kernel.org>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Cc: netdev@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Luis R. Rodriguez <mcgrof@kernel.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-3-git-send-email-chris@chris-wilson.co.uk
When setting up the overlay page, we pin it into the GGTT (when using
virtual addresses) and store the offset as overlay->flip_addr. Rather
than doing a lookup of the GGTT address everytime, we can use the known
address instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461833819-3991-2-git-send-email-chris@chris-wilson.co.uk
Propagate the real error from drm_gem_object_init(). Note this also
fixes some confusion in the error return from i915_gem_alloc_object...
v2:
(Matthew Auld)
- updated new users of gem_alloc_object from latest drm-nightly
- replaced occurrences of IS_ERR_OR_NULL() with IS_ERR()
v3:
(Joonas Lahtinen)
- fix double "From:" in commit message
- add goto teardown path
v4:
(Matthew Auld)
- rebase with i915_gem_alloc_object name change
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461587533-8841-1-git-send-email-matthew.auld@intel.com
[Joonas: Removed spurious " = NULL" from _init() function]
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Faced with sporadic machine hangs on gen7, that mimic the issue of
concurrent writes to the same cacheline and seem to start with
commit 9b9ed30936 (drm/i915: Remove forcewake dance from seqno/irq
barrier on legacy gen6+), let us restore the spinlock around the mmio
read.
Fixes: 9b9ed30936 (drm/i915: Remove forcewake dance from seqno/irq...)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461744121-27051-1-git-send-email-chris@chris-wilson.co.uk
Tested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
I just noticed that VLV/CHV have a RAWCLK_FREQ register just like PCH
platforms. It lives in the display power well, so we should update it
when enabling the power well.
Interestingly the BIOS seems to leave it at the reset value (125) which
doesn't match the rawclk frequency on VLV/CHV (200 MHz). As always with
these register, the spec is extremely vague what the register does. All
it says is: "This is used to generate a divided down clock for
miscellaneous timers in display." Based on a quick test, at least AUX
and PWM appear to be unaffected by this.
But since the register is there, let's configure it in accordance with
the spec.
Note that we have to move intel_update_rawclk() to occur before we
touch the power wells, so that the dev_priv->rawclk_freq is already
populated when the disp2 enable hook gets called for the first time.
I think this should be safe to do on other platforms as well.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461768202-17544-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Check for VLV/CHV instead if !BXT when re-enabling DPOunit clock gating
after DSI disable. That's what we checked when disabling the clock
gating when enabling DSI.
Also use the same temporary variable name in both cases, and toss in a
bit of dev vs. dev_priv cleanup while at it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460996305-30453-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Add support for CHV gpio programming in DSI gpio elements.
v2: Overhaul macros according to Ville's review.
v3: Address Ville's review:
- swap E and SE gpio ranges
- add a note about max SE index
- use GPO, not HIZ
- swap cfg0 and cfg1
v4: fix port for dsi sequence versions 1 and 2
[Rewritten by Jani, based on earlier work by Yogesh and Deepak.]
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/bdaaf9915a5005305b31bb26cf619a5a82472f2a.1461666263.git.jani.nikula@intel.com
For dual link panel scenarios there are new fields added in the
VBT which indicate on which port the PWM cntrl and CABC ON/OFF
commands needs to be sent.
v2: Moving the comment to intel_dsi.h(Jani)
v3: Renaming the field names (Jani)
v4 by Jani: make this patch only about VBT
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459346623-30752-2-git-send-email-jani.nikula@intel.com
This patch adds support for eDP backlight control using DPCD registers to
backlight hooks in intel_panel.
It checks for backlight control over AUX channel capability and sets up
function pointers to get and set the backlight brightness level if
supported.
v2: Moved backlight functions from intel_dp.c into a new file
intel_dp_aux_backlight.c. Also moved reading of eDP display control
registers to intel_dp_get_dpcd
v3: Correct some formatting mistakes
v4: Updated to use AUX backlight control if PWM control is not possible
(Jani)
v5: Moved call to initialize backlight registers to dp_aux_setup_backlight
v6: Check DP_EDP_BACKLIGHT_PIN_ENABLE_CAP is disabled before setting up AUX
backlight control. To fix BLM_PWM_ENABLE igt test warnings on bdw_ultra
v7: Add enable_dpcd_backlight module parameter.
v8: Rebase onto latest drm-intel-nightly branch
v9: Remove changes to intel_dp_dpcd_read_wake
Split addition edp_dpcd variable into a separate patch
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
[Jani: whitepace changes to appease checkpatch]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459865452-9138-4-git-send-email-yetundex.adebisi@intel.com
Can use the new vma->is_ggtt to simplify the check and
remove the local variables.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Can use vma->is_ggtt to simplify the check and also switch the
BUG_ON to GEM_BUG_ON which is more appropriate for this.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Only caller is i915_gem_obj_ggtt_size which only cares about
GGTT so simplify it and implement under that name.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Because having both i915_gem_object_alloc() and i915_gem_alloc_object()
(with different return conventions) is just too confusing!
(i915_gem_object_alloc() is the low-level memory allocator, and remains
unchanged, whereas i915_gem_alloc_object() is a constructor that ALSO
initialises the newly-allocated object.)
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461348872-4702-1-git-send-email-david.s.gordon@intel.com
Move the better constructs/comments from i915_gem_stolen.c to
early-quirks.c and increase readability in preparation of only
having one set of functions.
- intel_stolen_base -> gen3_stolen_base
- use phys_addr_t instead of u32 for address for future proofing
v2:
- Print the invalid register values (Chris)
(Omitting the register prefix as it's visible from backtrace.)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
This patch applies a performance enhancement workaround
based on analysis of DX and OCL S-Curve workloads. We
increase the General Priority Credits for L3SQ from the
hardware default of 56 to the max value 62, and decrease
the High Priority credits from 8 to 2.
v2: Only apply to B0 onwards
v3: Move w/a to per engine init, ie bxt_init_workarounds
Signed-off-by: Tim Gore <tim.gore@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461314761-36854-1-git-send-email-tim.gore@intel.com
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
As a part of WaGsvDisableTurbo, Driver makes an early exit from the
Gen9 Turbo enabling function, so doesn't program the Turbo Control register.
But BIOS could leave the Hw Turbo as enabled, so need to explicitly clear
out the Control register just to avoid inconsitency with debugfs
interface, which will show Turbo as enabled only and that is not expected
after adding the WaGsvDisableTurbo. Apart from this there is no problem
even if the Turbo is left enabled in the Control register, as the Up/Down
interrupts would remain masked.
v2: Add explicit clearing of Turbo Control register to *_disable_rps()
also for the similar consistency (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-2-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There are certain registers, which captures the time elapsed in the
in current Up/Down EI, for how long GT has been Idle/Busy/Avg in the
current Up/Down EI and also in the previous Up/Down EI.
These register values are reported by the i915_frequency_info debugfs
interface. The Driver prints the 'us' suffix after the values, albeit
they are actually in raw form & not in microsecond units.
This patch removes the 'us' suffix so that its clear to User that values
are indeed in raw form.
v2: Present the values in microseconds unit also, after platform
specific conversion (Chris)
v3: Add a space between raw & microsecond value (Chris)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-3-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Added a new GT_PM_INTERVAL_TO_US macro to perform the platform
specific conversion of PM time interval values to microseconds unit.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Akash Goel <akash.goel@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461350146-23454-1-git-send-email-akash.goel@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Somehow my SNB GT1 (Dell XPS 8300) gets very unhappy around
GPU hangs if the RPS EI/thresholds aren't suitably aligned.
It seems like scheduling/timer interupts stop working somehow
and things get stuck eg. in usleep_range().
I bisected the problem down to
commit 8a5864377b ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
I observed that before all the values were at least multiples of 25,
but afterwards they are not. And rounding things up to the next multiple
of 25 does seem to help, so lets' do that. I also tried roundup(..., 5)
but that wasn't sufficient. Also I have no idea if we might need this sort of
thing on gen9+ as well.
These are the original EI/thresholds:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10250
GEN6_RP_UP_THRESHOLD 9225
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 8000
GEN6_RP_UP_THRESHOLD 6800
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
These are after 8a5864377b:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10156
GEN6_RP_UP_THRESHOLD 9140
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7812
GEN6_RP_UP_THRESHOLD 6640
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
And these are what we have after this patch:
LOW_POWER
GEN6_RP_UP_EI 12500
GEN6_RP_UP_THRESHOLD 11875
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 21250
BETWEEN
GEN6_RP_UP_EI 10175
GEN6_RP_UP_THRESHOLD 9150
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 18750
HIGH_POWER
GEN6_RP_UP_EI 7825
GEN6_RP_UP_THRESHOLD 6650
GEN6_RP_DOWN_EI 25000
GEN6_RP_DOWN_THRESHOLD 15000
Cc: stable@vger.kernel.org
Cc: Akash Goel <akash.goel@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Testcase: igt/kms_pipe_crc_basic/hang-read-crc-pipe-B
Fixes: 8a5864377b ("drm/i915/skl: Restructured the gen6_set_rps_thresholds function")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461159836-9108-1-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
This patch does the following:
- Fakes live status of HDMI as connected (even if that's not).
While testing certain (monitor + cable) combinations with
various intel platforms, it seems that live status register
doesn't work reliably on some older devices. So limit the
live_status check for HDMI detection, only for platforms
from gen7 onwards.
V2: restrict faking live_status to certain platforms
V3: (Ville)
- keep the debug message for !live_status case
- fix indentation of comment
- remove "warning" from the debug message
(Jani)
- Change format of fix details in the commit message
Fixes: 237ed86c69 ("drm/i915: Check live status before reading edid")
Cc: stable@vger.kernel.org # v4.4
Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461237606-16491-1-git-send-email-shashank.sharma@intel.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
It's possible that BIOS enables PHY0, but it programmes only the first
channel on it. Since we program the PHYs only during driver loading this
is an incorrect configuration from the driver's point of view, since we
may use both channels eventually. Detect this scenario and force
reprogramming the PHY in this case.
The actual scenario for me was that the lane optimization for the second
channel in PHY0 was not setup by BIOS and so a state verification
warning was triggered. Everything else was setup properly.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461174366-16758-4-git-send-email-imre.deak@intel.com
If we skipped PHY0 initialization because it was already enabled by
BIOS, we still have to wait for the PHY1 GRC calibration as that is
done as part of the PHY0 init.
v2:
- Use the actual PHY index in the debug message in
broxton_phy_wait_grc_done() (Ville)
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461255561-1644-1-git-send-email-imre.deak@intel.com
It's possible that BIOS enables PHY1 only to read out the GRC value from
it to be used in PHY0 and then disables PHY1. In this case we can't use
the PHY1 GRC value for state verification, so use instead the one in PHY0
always.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461174366-16758-2-git-send-email-imre.deak@intel.com
Remove dev local and use to_i915() in gen8_ppgtt_notify_vgt.
v2: use dev_priv directly for QUESTION_MACROS (Joonas Lahtinen)
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461323365-21256-1-git-send-email-matthew.auld@intel.com
Right after runtime resume we know that we can re-enable DC5, since we
just disabled DC9 and power well 2 is disabled. So enable DC5 explicitly
instead of delaying this until the next time we disable power well 2.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-5-git-send-email-imre.deak@intel.com
After suspend-to-ram or -disk we don't know what power state the display
HW will be, DC0 or DC9 are both possible states, so reset the software
DC state tracking in these cases. This gets rid of 'DC state mismatch'
error messages during resuming from ram or disk where we expected to be
in DC9 (as set by the suspend handler) but we are in DC0.
v2:
- Remove extra WS in gen9_sanitize_dc_state() (Bob)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-4-git-send-email-imre.deak@intel.com
Initially we thought that the platform specific suspend/resume sequences
can be shared between the runtime and system suspend/resume handlers.
This turned out to be not true, we have quite a few differences on most
of the platforms. This was realized already earlier by Paulo who
inlined the platform specific resume_prepare handlers. We have the
same problem with the corresponding suspend_complete handlers, there are
platform differences that make it unfeasible to share the code between
the runtime and system suspend paths. Also now we call functions that
need to be paired like hsw_enable_pc8()/hsw_disable_pc8() from different
levels of the call stack, which is confusing. Fix this by inlining the
suspend_complete handlers too.
This is also needed by the next patch that removes a redundant
uninit/init call during system suspend/resume on BXT.
No functional change.
CC: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
[s/uninline/inline in the commit message]
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-2-git-send-email-imre.deak@intel.com
In commit 5f304c8736 ("drm/i915/kbl: Reset secondary power well requests
left on by DMC/KVMR") I forgot about the fact that SKL==KBL most of the
time and that a secondary MISC IO power well request left on by the DMC is
"expected". Tune down the corresponding WARN to be a debug message. This
was caught by CI suspend tests.
CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461060036-19043-1-git-send-email-imre.deak@intel.com
It was noticed on bug #94087 that module parameter
i915.edp_vswing=2 that should override the VBT setting
to use default voltage swing (400 mV) was not applied
for Broadwell.
This patch provides a fix for this by checking if default
i.e. higher voltage swing is requested to be used and
applies the DDI translations table for DP instead of eDP
(low vswing) table.
v2: Combine two if statements into one (Jani)
v3: Change dev_priv->edp_low_vswing to use dev_priv->vbt.edp.low_vswing
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94087
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461155942-7749-1-git-send-email-mika.kahola@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
The newly-introduced function i915_gem_object_pin_map() returns an
ERR_PTR (not NULL) if the pin-and-map opertaion fails, so that's what we
must check for. And it's nicer not to assign such a pointer-or-error to
a structure being filled in until after it's been validated, so we
should keep it local and avoid exporting a bogus pointer. Also, for
clarity and symmetry, we should clear 'virtual_start' along with 'vma'
when unmapping a ringbuffer.
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Now that we keep the GuC client process descriptor permanently mapped,
we don't really need to keep a local copy of the GuC's work-queue-head.
So we can simplify the code a little by not doing this.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Don't use kmap_atomic() for doorbell & process descriptor access.
This patch fixes the BUG shown below, where the thread could sleep
while holding a kmap_atomic mapping. In order not to need to call
kmap_atomic() in this code path, we now set up a permanent kernel
mapping of the shared doorbell and process-descriptor page, and
use that in all doorbell and process-descriptor related code.
BUG: scheduling while atomic: gem_close_race/1941/0x00000002
Modules linked in: hid_generic usbhid i915 asix usbnet libphy mii
i2c_algo_bit drm_kms_helper cfbfillrect syscopyarea cfbimgblt
sysfillrect sysimgblt fb_sys_fops cfbcopyarea drm coretemp i2c_hid
hid video pinctrl_sunrisepoint pinctrl_intel acpi_pad nls_iso8859_1
e1000e ptp psmouse pps_core ahci libahci
CPU: 0 PID: 1941 Comm: gem_close_race Tainted: G U 4.4.0-160121+ #123
Hardware name: Intel Corporation Skylake Client platform/Skylake AIO
DDR3L RVP10, BIOS SKLSE2R1.R00.X100.B01.1509220551 09/22/2015
0000000000013e40 ffff880166c27a78 ffffffff81280d02 ffff880172c13e40
ffff880166c27a88 ffffffff810c203a ffff880166c27ac8 ffffffff814ec808
ffff88016b7c6000 ffff880166c28000 00000000000f4240 0000000000000001
Call Trace:
[<ffffffff81280d02>] dump_stack+0x4b/0x79
[<ffffffff810c203a>] __schedule_bug+0x41/0x4f
[<ffffffff814ec808>] __schedule+0x5a8/0x690
[<ffffffff814ec927>] schedule+0x37/0x80
[<ffffffff814ef3fd>] schedule_hrtimeout_range_clock+0xad/0x130
[<ffffffff81090be0>] ? hrtimer_init+0x10/0x10
[<ffffffff814ef3f1>] ? schedule_hrtimeout_range_clock+0xa1/0x130
[<ffffffff814ef48e>] schedule_hrtimeout_range+0xe/0x10
[<ffffffff814eef9b>] usleep_range+0x3b/0x40
[<ffffffffa01ec109>] i915_guc_wq_check_space+0x119/0x210 [i915]
[<ffffffffa01da47c>] intel_logical_ring_alloc_request_extras+0x5c/0x70 [i915]
[<ffffffffa01cdbf1>] i915_gem_request_alloc+0x91/0x170 [i915]
[<ffffffffa01c1c07>] i915_gem_do_execbuffer.isra.25+0xbc7/0x12a0 [i915]
[<ffffffffa01cb785>] ? i915_gem_object_get_pages_gtt+0x225/0x3c0 [i915]
[<ffffffffa01d1fb6>] ? i915_gem_pwrite_ioctl+0xd6/0x9f0 [i915]
[<ffffffffa01c2e68>] i915_gem_execbuffer2+0xa8/0x250 [i915]
[<ffffffffa00f65d8>] drm_ioctl+0x258/0x4f0 [drm]
[<ffffffffa01c2dc0>] ? i915_gem_execbuffer+0x340/0x340 [i915]
[<ffffffff8111590d>] do_vfs_ioctl+0x2cd/0x4a0
[<ffffffff8111eac2>] ? __fget+0x72/0xb0
[<ffffffff81115b1c>] SyS_ioctl+0x3c/0x70
[<ffffffff814effd7>] entry_SYSCALL_64_fastpath+0x12/0x6a
------------[ cut here ]------------
v4:
Only tear down doorbell & kunmap() client object if we actually
succeeded in allocating a client object (Tvrtko Ursulin)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93847
Original-version-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Tvtrko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
