The Allwinner H6 SoC have its pin controllers with the first IRQ-capable
GPIO bank at IRQ bank 1 and the second bank at IRQ bank 5.
Change the current code that uses IRQ bank base to a IRQ bank map, in
order to support the case that holes exist among IRQ banks.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Old pinctrl drivers will need to disable strict mode for various reasons,
among which:
- Some DT will still have a pinctrl group for each GPIO used, which will
be rejected by pin_request. While we could remove those nodes, we still
have to deal with old DTs.
- Some GPIOs on these boards need to have their pin configuration changed
(for bias or current), and there's no clear migration path
Let's disable the strict mode on those SoCs so that there's no breakage.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get essentially the same change, so they are handled in batch.
Changes are (1) use builtin_platform_driver, (2) use init.h header
(3) delete module_exit related code, (4) delete MODULE_DEVICE_TABLE,
and (5) delete MODULE_LICENCE/MODULE_AUTHOR and associated tags.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We do delete the MODULE_LICENSE etc. tags since all that information
is already contained at the top of each file in the comments.
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Hongzhou Yang <hongzhou.yang@mediatek.com>
Cc: Fabian Frederick <fabf@skynet.be>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Vishnu Patekar <vishnupatekar0510@gmail.com>
Cc: Mylene Josserand <mylene.josserand@free-electrons.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PG8, PG9 is said to be the CTS/RTS pins for UART1 according to the A23/33
datasheets. However, the function is wrongly named "uart2" in the pinctrl
driver. This patch fixes this by modifying them to be named "uart1".
Cc: stable@vger.kernel.org
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In sun4/5/6/7i, all the pin function related to NAND0 controller is
named "nand0". However, in sun8i, some of the functions are named as
"nand". This patch renamed them to "nand0", for the consistency.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinctrl-sun8i-a33.c (and the dts) declare only 2 interrupt banks,
where as the closely related a23 has 3 banks. This matches with the
datasheet for the A33 where only interrupt banks B and G are specified
where as the A23 has banks A, B and G.
However the A33 being the A23 derative it is means that the interrupt
configure/status io-addresses for the 2 banks it has are not changed
from the A23, iow they have the same address as if bank A was still
present. Where as the sunxi pinctrl currently tries to use the A23 bank
A addresses for bank B, since the pinctrl code does not know about the
removed bank A.
Add a irq_bank_base parameter and use this where appropriate to take
the missing bank A into account.
This fixes external interrupts not working on the A33 (tested with
an i2c touchscreen controller which uses an external interrupt).
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A33 PIO has 7 ports which starts from PB and has two interrupt ports.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
