DMA allocated memory is lost in be_cmd_get_profile_config() when we
call it with non-NULL port_res parameter.
Signed-off-by: Petr Oros <poros@redhat.com>
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add flags to enable/disable supported chips in be2net.
With disable support are removed coresponding PCI IDs and
also codepaths with [BE2|BE3|BEx|lancer|skyhawk]_chip checks.
Disable chip will reduce module size by:
BE2 ~2kb
BE3 ~3kb
Lancer ~10kb
Skyhawk ~9kb
When enable skyhawk only it will reduce module size by ~20kb
New help style in Kconfig
Reviewed-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Petr Oros <poros@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114787 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_info message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch handles a TX-timeout as follows:
1) This patch gathers and prints the following info that can
help in diagnosing the cause of a TX-timeout.
a) TX queue and completion queue entries.
b) SKB and TCP/UDP header details.
2) For Lancer NICs (TX-timeout recovery is not supported for
BE3/Skyhawk-R NICs), it recovers from the TX timeout as follows:
a) On a TX-timeout, driver sets the PHYSDEV_CONTROL_FW_RESET_MASK
bit in the PHYSDEV_CONTROL register. Lancer firmware goes into
an error state and indicates this back to the driver via a bit
in a doorbell register.
b) Driver detects this and calls be_err_recover(). DMA is disabled,
all pending TX skbs are unmapped and freed (be_close()). All rings
are destroyed (be_clear()).
c) The driver waits for the FW to re-initialize and re-creates all
rings along with other data structs (be_resume())
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Unionize two u8 fields where only one of them is used depending on NIC
chipset.
- Move recovery_supported field after that union
These changes eliminate 7-bytes hole in the struct and makes it smaller
by 8 bytes.
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-order fields in struct be_eq_obj to ensure that .napi field begins
at start of cache-line. Also the .adapter field is moved to the first
cache-line next to .q field and 3 fields (idx,msi_idx,spurious_intr)
and the 4-bytes hole to 3rd cache-line.
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The event queue description (be_eq_obj.desc) field is used only to format
string for IRQ name and it is not really needed to hold this value.
Remove it and use local variable to format string for IRQ name.
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit fb6113e688 ("be2net: get rid of custom busy poll code")
replaced custom busy-poll code by the generic one but left several
macros and fields in struct be_eq_obj that are currently unused.
Remove this stuff.
Fixes: fb6113e688 ("be2net: get rid of custom busy poll code")
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 2632bafd74 ("be2net: fix adaptive interrupt coalescing")
introduced a separate struct be_aic_obj to hold AIC information but
unfortunately left the old stuff in be_eq_obj. So remove it.
Fixes: 2632bafd74 ("be2net: fix adaptive interrupt coalescing")
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for 0xE00 (RECOVERABLE_ERR) along with ARMFW UE (0x0)
in be_detect_error() to know whether the error is valid error or not
Fixes: 673c96e5a ("be2net: Fix UE detection logic for BE3")
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer the direct use of octal for permissions.
Done with checkpatch -f --types=SYMBOLIC_PERMS --fix-inplace
and some typing.
Miscellanea:
o Whitespace neatening around these conversions.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: This is compile only tested as I have no access to the hw.
No benefit gained except for some self-documenting.
add/remove: 0/0 grow/shrink: 0/0 up/down: 0/0 (0)
Function old new delta
Total: Before=2757703, After=2757703, chg +0.00%
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the driver receives a TX CQE with status as 0x1 or 0x9 or 0xb,
the completion indexes should not be used. The driver must stop
consuming CQEs from this TXQ/CQ. The TXQ from this point on-wards
to be in a bad state. Driver should destroy and recreate the TXQ.
0x1: LANCER_TX_COMP_LSO_ERR
0x9 LANCER_TX_COMP_SGE_ERR
0xb: LANCER_TX_COMP_PARITY_ERR
Reset the adapter if driver sees this error in TX completion. Also
adding sge error counter in ethtool stats.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lancer HW cannot handle a TSO packet with a single segment.
Disable TSO/GSO for such packets.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable head is initialized to a value that is never read and is
being updated to a new value a few lines later, hence this
initialization is redundant and can be safely removed as well
as the now unused pointer txq.
Cleans up clang warning:
drivers/net/ethernet/emulex/benet/be_main.c:996:6: warning: Value
stored to 'head' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolved Warning: networking block comments don't use an empty /* line,
use /* Comment...
Issue found by checkpatch.
Signed-off-by: Rohit Visavalia <rohit.visavalia@softnautics.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
en_rx_am.c was deleted in 'net-next' but had a bug fixed in it in
'net'.
The esp{4,6}_offload.c conflicts were overlapping changes.
The 'out' label is removed so we just return ERR_PTR(-EINVAL)
directly.
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 6221906694 ("be2net: Request RSS capability of Rx interface
depending on number of Rx rings") modified be_update_queues() so the
IFACE (HW representation of the netdevice) is destroyed and then
re-created. This causes a regression because potential promiscuous mode
is not restored properly during be_open() because the driver thinks
that the HW has promiscuous mode already enabled.
Note that Lancer is not affected by this bug because RX-filter flags are
disabled during be_close() for this chipset.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: 6221906694 ("be2net: Request RSS capability of Rx interface depending on number of Rx rings")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the ARRAY_SIZE macro on array cmd_priv_map to determine size of the
array. Improvement suggested by coccinelle.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Please do not apply this to mainline directly, instead please re-run the
coccinelle script shown below and apply its output.
For several reasons, it is desirable to use {READ,WRITE}_ONCE() in
preference to ACCESS_ONCE(), and new code is expected to use one of the
former. So far, there's been no reason to change most existing uses of
ACCESS_ONCE(), as these aren't harmful, and changing them results in
churn.
However, for some features, the read/write distinction is critical to
correct operation. To distinguish these cases, separate read/write
accessors must be used. This patch migrates (most) remaining
ACCESS_ONCE() instances to {READ,WRITE}_ONCE(), using the following
coccinelle script:
----
// Convert trivial ACCESS_ONCE() uses to equivalent READ_ONCE() and
// WRITE_ONCE()
// $ make coccicheck COCCI=/home/mark/once.cocci SPFLAGS="--include-headers" MODE=patch
virtual patch
@ depends on patch @
expression E1, E2;
@@
- ACCESS_ONCE(E1) = E2
+ WRITE_ONCE(E1, E2)
@ depends on patch @
expression E;
@@
- ACCESS_ONCE(E)
+ READ_ONCE(E)
----
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: davem@davemloft.net
Cc: linux-arch@vger.kernel.org
Cc: mpe@ellerman.id.au
Cc: shuah@kernel.org
Cc: snitzer@redhat.com
Cc: thor.thayer@linux.intel.com
Cc: tj@kernel.org
Cc: viro@zeniv.linux.org.uk
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/1508792849-3115-19-git-send-email-paulmck@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
IPv6 TSO requests with extension hdrs are a problem to the
Lancer and BEx chips. Workaround is to disable TSO6 feature
for such packets.
Also in Lancer chips, MSS less than 256 was resulting in TX stall.
Fix this by disabling GSO when MSS less than 256.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
warning: variable ‘netdev’ set but not used
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
On certain platforms BE3 chips may indicate spurious UEs (unrecoverable
error). Because of the UE detection logic was disabled in the driver
for BE3 chips. Because of this, even in cases of a real UE,
a failover will not occur. This patch re-enables UE detection on BE3
and if a UE is detected, reads the POST register. If the POST register,
reports either a FAT_LOG_STATE or a ARMFW_UE, then it means that a valid
UE occurred in the chip.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At least some of the be2net cards do not seem to be capabled
of performing checksum offload computions on Q-in-Q packets.
In these case, the recevied checksum on the remote is invalid
and TCP syn packets are dropped.
This patch adds a call to check disbled acceleration features
on Q-in-Q tagged traffic.
CC: Sathya Perla <sathya.perla@broadcom.com>
CC: Ajit Khaparde <ajit.khaparde@broadcom.com>
CC: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
CC: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use time_before_eq for time comparison more safe and dealing
with timer wrapping to be future-proof.
Signed-off-by: Karim Eshapa <karim.eshapa@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We disable VxLAN offload when more than 1 UDP port is added to the driver,
since Skyhawk doesn't support offload with multiple ports. The existing
driver design expects the user to delete all port configurations and create
a configuration with a single UDP port for VxLAN offload to be re-enabled.
Remove this restriction by tracking the ports added and re-enabling offload
when ports get deleted and only 1 port is left.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Reviewed-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cpu_to_le32() for link_config variable in set_logical_link_config
command as this variable is of type u32.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compared to custom busy_poll, the generic NAPI one is better, since
it allows to use GRO, and it removes a lot of code and extra locked
operations in fast path.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent commit 3439352916 ("be2net: fix MAC addr setting on privileged
BE3 VFs") allows privileged BE3 VFs to set its MAC address during
initialization. Although the initial MAC for such VFs is already
programmed by parent PF the subsequent setting performed by VF is OK,
but in certain cases (after fresh boot) this command in VF can fail.
The MAC should be initialized only when:
1) no MAC is programmed (always except BE3 VFs during first init)
2) programmed MAC is different from requested (e.g. MAC is set when
interface is down). In this case the initial MAC programmed by PF
needs to be deleted.
The adapter->dev_mac contains MAC address currently programmed in HW so
it should be zeroed when the MAC is deleted from HW and should not be
filled when MAC is set when interface is down in be_mac_addr_set() as
no programming is performed in this case.
Example of failure without the fix (immediately after fresh boot):
# ip link set eth0 up <- eth0 is BE3 PF
be2net 0000:01:00.0 eth0: Link is Up
# echo 1 > /sys/class/net/eth0/device/sriov_numvfs <- Create 1 VF
...
be2net 0000:01:04.0: Emulex OneConnect(be3): VF port 0
# ip link set eth8 up <- eth8 is created privileged VF
be2net 0000:01:04.0: opcode 59-1 failed:status 1-76
RTNETLINK answers: Input/output error
# echo 0 > /sys/class/net/eth0/device/sriov_numvfs <- Delete VF
iommu: Removing device 0000:01:04.0 from group 33
...
# echo 1 > /sys/class/net/eth0/device/sriov_numvfs <- Create it again
iommu: Removing device 0000:01:04.0 from group 33
...
# ip link set eth8 up
be2net 0000:01:04.0 eth8: Link is Up
Initialization is now OK.
v2 - Corrected the comment and condition check suggested by Suresh & Harsha
Fixes: 3439352916 ("be2net: fix MAC addr setting on privileged BE3 VFs")
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Acked-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During interface opening MAC address stored in netdev->dev_addr is
programmed in the HW with exception of BE3 VFs where the initial
MAC is programmed by parent PF. This is OK when MAC address is not
changed when an interfaces is down. In this case the requested MAC is
stored to netdev->dev_addr and later is stored into HW during opening.
But this is not done for all BE3 VFs so the NIC HW does not know
anything about this change and all traffic is filtered.
This is the case of bonding if fail_over_mac == 0 where the MACs of
the slaves are changed while they are down.
The be2net behavior is too restrictive because if a BE3 VF has
the FILTMGMT privilege then it is able to modify its MAC without
any restriction.
To solve the described problem the driver should take care about these
privileged BE3 VFs so the MAC is programmed during opening. And by
contrast unpriviled BE3 VFs should not be allowed to change its MAC
in any case.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
BE3 VFs without FILTMGMT privilege are not allowed to modify its MAC,
VLAN table and UC/MC lists. So don't try to delete MAC on such VFs.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return value from be_mcc_notify_wait() contains a base completion status
together with an additional status. The base_status() macro need to be
used to access base status.
Fixes: e3a7ae2 be2net: Changing MAC Address of a VF was broken
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adapter->pmac_id[0] item is used for primary MAC address but
this is not true for adapter->uc_list[0] as is assumed in
be_set_uc_list(). There are N UC addresses copied first from net_device
to adapter->uc_list[1..N] and then N UC addresses from
adapter->uc_list[0..N-1] are sent to HW. So the last UC address is never
stored into HW and address 00:00:00:00;00:00 (from uc_list[0]) is used
instead.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: b717241 be2net: replace polling with sleeping in the FW completion path
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 988d44b "be2net: Avoid redundant addition of mac address in HW"
introduced be_dev_mac_add & be_uc_mac_add helpers that incorrectly
access adapter->uc_list as an array of bytes instead of an array of
be_eth_addr. Consequently NIC is not filled with valid data so unicast
filtering is broken.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Fixes: 988d44b be2net: Avoid redundant addition of mac address in HW
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VXLAN offloading is enabled, be_features_check() tries to check if
an encapsulated packet is indeed a VXLAN packet. The check is not strict
enough, and considers any UDP-encapsulated ethernet frame with a 8-byte
tunnel header as being VXLAN. Unfortunately, both GENEVE and VXLAN-GPE
have a 8-byte header, so they get through this check.
Force the UDP destination port to be the one that has been offloaded to
hardware.
Without this, GENEVE-encapsulated packets can end up having an incorrect
checksum when both a GENEVE and a VXLAN (offloaded) tunnel are
configured.
This is similar to commit a547224dce ("mlx4e: Do not attempt to
offload VXLAN ports that are unrecognized").
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently allocates 128 bytes of skb headroom.
This was found to be insufficient with some configurations
like Geneve tunnels, which resulted in skb head reallocations.
Increase the headroom to 256 bytes to fix this.
Signed-off-by: Kalesh A P <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
