Add support for offloading PRIO qdisc as root qdisc.
The support is for up to 8 bands.
Routed packets priority is determined by the DSCP field with the default
translations. Bridged packets priority is determined by the PCP field, if
exist, otherwise it is set to 0.
Since both options have only priorities 0-7, higher priorities mapping are
being ignored.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When routing ip packets, the kernel is setting the SKB's priority
based on the tos field of the packet.
Imitate this behavior in the mlxsw router, having the internal
switch priority of a routed packet determined according to its DS
field.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rdpm definition - router DSCP to priority mapping register.
This register will be utilized later to align the default mapping between
packet DSCP and switch-priority to the kernel's mapping between
packet priority and skb priority.
This is the first non-bit indexed register where the entries are arranged
in descending order, i.e., entry at offset 0 matches configuration for
dscp[63]. As a result, the item's step is converted into a signed variable
to support descending arrays [where step would be negative].
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit eb789980d0 ("mlxsw: spectrum_router: Populate adjacency
entries according to weights") the driver includes support for
non-equal-cost multipath, but IPv4 nexthops were the only user.
Now that the kernel supports weighted IPv6 nexthops, we can extend the
driver to support it as well.
This is done by assigning each nexthop its configured weight, so that it
will be populated accordingly in the device's adjacency table. The
`weight` parameter is also taken into account when comparing nexthop
groups in order not to consolidate non-identical groups.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF alignment tests got a conflict because the registers
are output as Rn_w instead of just Rn in net-next, and
in net a fixup for a testcase prohibits logical operations
on pointers before using them.
Also, we should attempt to patch BPF call args if JIT always on is
enabled. Instead, if we fail to JIT the subprogs we should pass
an error back up and fail immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
If a qdisc is being replaced by another qdisc of the same type, it can
simply override over its configuration.
However, if it replaces a qdisc of another type, it needs to be removed
before setting the new qdisc.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a generic qdisc replace function.
For that goal, add three functions to the qdisc ops struct:
* check_params: Checks if the given parameters are offloadable.
* replace: Offload the given parameters.
* clean_stats: clean the qdisc stats for the offloaded qdisc.
integrate RED offloading into using the new internal replace API.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a destroy function to the qdiscs ops struct.
Create a generic qdisc destroy function, that clears the qdisc metadata as
well as calling the specific qdisc destroy function.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Qdisc struct have the Qdisc_class_ops struct.
This patch introduces the similar ops struct for the mlxsw_sp_qdisc_ops
struct. It allows better readability as well as code reusability for the
common parts of some functions like destroy.
The first operations to be added are the statistics getters.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every qdisc op gets the qdisc handle ID as well as its location. Each one
of them, beside replace, checks if the handle doesn't match the qdisc in
the given location, and if so, it returns without running the actual op.
Unite these checks to one comparison function and avoid sending the handle
id to these ops.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tclass number is needed for most of the operations related to the qdisc in
the driver. Create a field for it in the mlxsw_sp_qdisc instead of passing
it to every function as parameter.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Improve readability by changing the clean stats function to handle only
RED. Qdiscs that will be offloaded in the future will have a clean stats
function of their own.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean RED offloaded stats and make them more generic by breaking the
generic qdisc stats to a struct of their own.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the value of the xstats requested from the driver for offloaded RED
to be incremental, like the normal stats.
It increases consistency - if a qdisc stops being offloaded its xstats
don't change.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the name of the stats struct to be generic, so it could be used for
other qdisc offload, that will be added in the next patches.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all the qdisc related data from the spectrum.h to spectrum_qdisc.c.
Create an init and fini functions for the qdiscs.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolve the sparse warning:
"sparse: Variable length array is used."
Use 2 arrays for 2 PRM register accesses.
Fixes: 96f17e0776 ("mlxsw: spectrum: Support RED qdisc offload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After performing reset driver polls on HW indication until learning
that the reset is done, but immediately after reset the device becomes
unresponsive which might lead to completion timeout on the first read.
Wait for 100ms before starting the polling.
Fixes: 233fa44bd6 ("mlxsw: pci: Implement reset done check")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 25cc72a338 ("mlxsw: spectrum: Forbid linking to devices that
have uppers") the driver forbids enslavement to netdevs that already
have uppers of their own, as this can result in various ordering
problems.
This requirement proved to be too strict for some users who need to be
able to enslave ports to a bridge that already has uppers. In this case,
we can allow the enslavement if the bridge is already known to us, as
any configuration performed on top of the bridge was already reflected
to the device.
Fixes: 25cc72a338 ("mlxsw: spectrum: Forbid linking to devices that have uppers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we remove the neighbour associated with a nexthop we should always
refuse to write the nexthop to the adjacency table. Regardless if it is
already present in the table or not.
Otherwise, we risk dereferencing the NULL pointer that was set instead
of the neighbour.
Fixes: a7ff87acd9 ("mlxsw: spectrum_router: Implement next-hop routing")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of overlapping changes. Also on the net-next side
the XDP state management is handled more in the generic
layers so undo the 'net' nfp fix which isn't applicable
in net-next.
Include a necessary change by Jakub Kicinski, with log message:
====================
cls_bpf no longer takes care of offload tracking. Make sure
netdevsim performs necessary checks. This fixes a warning
caused by TC trying to remove a filter it has not added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 63dd00fa3e.
RAUHT DELETE_ALL seems to trigger a bug in FW. That manifests by later
calls to RAUHT ADD of an IPv6 neighbor to fail with "bad parameter"
error code.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Fixes: 63dd00fa3e ("mlxsw: spectrum_router: Add batch neighbour deletion")
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Learning is currently enabled for ports which are OVS slaves -
even though OVS doesn't need this indication.
Since we're not associating a fid with the port, HW would continuously
notify driver of learned [& aged] MACs which would be logged as errors.
Fixes: 2b94e58df5 ("mlxsw: spectrum: Allow ports to work under OVS master")
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, whenever the NETIF_F_HW_TC feature changes, we silently
always allow it, but we actually do not disable the flows in HW
on disable. That breaks user's expectations. So just forbid
the feature disable in case there are any filters offloaded.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcfm_dev always points to the correct netdev and we already
hold a refcnt, so no need to use tcfm_ifindex to lookup again.
If we would support moving target netdev across netns, using
pointer would be better than ifindex.
This also fixes dumping obsolete ifindex, now after the
target device is gone we just dump 0 as ifindex.
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_nexthop_rif_update() walks the list of nexthops
associated with a RIF, and updates the corresponding entries in the
switch. It is used in particular when a tunnel underlay netdevice moves
to a different VRF, and all the nexthops are migrated over to a new RIF.
The problem is that each nexthop holds a reference to its RIF, and that
is not updated. So after the old RIF is gone, further activity on these
nexthops (such as downing the underlay netdevice) dereferences a
dangling pointer.
Fix the issue by updating rif of impacted nexthops before calling
mlxsw_sp_nexthop_rif_update().
Fixes: 0c5f1cd5ba ("mlxsw: spectrum_router: Generalize __mlxsw_sp_ipip_entry_update_tunnel()")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some tunnels that are offloadable on their own can nonetheless be
demoted to slow path if their local address is in conflict with that of
another tunnel. When a route is formed for such a tunnel,
mlxsw_sp_nexthop_ipip_init() fails to find the corresponding IPIP entry,
and that triggers a FIB abort.
Resolve the problem by not assuming that a tunnel for which
mlxsw_sp_ipip_ops.can_offload() holds also automatically has an IPIP
entry.
Fixes: af641713e9 ("mlxsw: spectrum_router: Onload conflicting tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlxsw driver currently doesn't offload GRE tunnels if they have the
same local address and use the same underlay VRF. When such a situation
arises, the tunnels in conflict are demoted to slow path.
However, the current code only verifies this condition on tunnel
creation and tunnel change, not when a tunnel is moved to a different
VRF. When the tunnel has no bound device, underlay and overlay are the
same. Thus moving a tunnel moves the underlay as well, and that can
cause local address conflict.
So modify mlxsw_sp_netdevice_ipip_ol_vrf_event() to check if there are
any conflicting tunnels, and demote them if yes.
Fixes: af641713e9 ("mlxsw: spectrum_router: Onload conflicting tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a new local route is added, an IPIP entry is looked up to determine
whether the route should be offloaded as a tunnel decap or as a trap.
That decision should take into account whether the tunnel netdevice in
question is actually IFF_UP, and only install a decap offload if it is.
Fixes: 0063587d35 ("mlxsw: spectrum: Support decap-only IP-in-IP tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some systems, when we unsplit a port we need to re-create two ports
instead. On other systems, only one needs to be re-created.
Do not try to create a port if during driver initialization it was
assigned a negative module number, which is invalid.
This avoids the following error during unsplit:
[ 941.012478] mlxsw_spectrum 0000:01:00.0: Port 43: Failed to map module
The error is harmless and caused by the fact that a local port is
already mapped to module 0.
Fixes: be94535f95 ("mlxsw: spectrum: Make split flow match firmware requirements")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 4a3c67a6e7 ("mlxsw: spectrum_router: Don't batch neighbour
deletion") I removed the support for batch deletion of neighbours on a
router interface (RIF) since at that time the firmware did not support
it for IPv6 neighbours.
This is now supported by the version enforced by the driver, so there is
no reason to delete neighbours one by one anymore.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the VID create error handling
case instead of 0, as done elsewhere in this function.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ndo_setup_tc with enum tc_setup_type value of
TC_SETUP_QDISC_STATS. This call updates the generic qdisc stats from the
cache if the handle ID that is asked for matching the root qdisc ID and
fails otherwise.
Currently doesn't support qlen and rqueues.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ndo_setup_tc with enum tc_setup_type value of
TC_SETUP_RED_XSTATS. This call returns the RED qdisc xstats from the cache
if the handle ID that is asked for matching the root qdisc ID and fails
otherwise.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add more statistics to be collected from the HW periodically. These stats
are tclass based (beside ECN marked packet, that exist only port based).
They are needed to expose RED qdisc stats and xstats correctly.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the counter group definitions for 2 new counter groups
which are necessary for gaining ECN & wred counters.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for ndo_setup_tc with enum tc_setup_type value of TC_SETUP_RED.
This call sets RED qdisc on a traffic class.
This patch supports RED qdisc only as a root qdisc and set in on the
default tclass. It can be set with or without ECN.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds 2 new registers:
- Congestion WRED ECN TClass Profile Register [CWTP]
- Congestion WRED ECN TClass and Pool Mapping Register [CWTPM]
These registers would later be needed to offload RED-related
functionality to the HW.
Signed-off-by: Yuval Mintz <yuvalm@mellanox.com>
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the bound device of a tunnel device is down, encapsulated packets
are not egressed anymore, but tunnel decap still works. Extend
mlxsw_sp_nexthop_rif_update() to take IFF_UP into consideration when
deciding whether a given next hop should be offloaded.
Because the new logic was added to mlxsw_sp_nexthop_rif_update(), this
fixes the case where a newly-added tunnel has a down bound device, which
would previously be fully offloaded. Now the down state of the bound
device is noted and next hops forwarding to such tunnel are not
offloaded.
In addition to that, notice NETDEV_UP and NETDEV_DOWN of a bound device
to force refresh of tunnel encap route offloads.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bound device of an IP-in-IP tunnel changes, such as through
'ip tunnel change name $name dev $dev', the loopback backing the tunnel
needs to be recreated.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes to L3 tunnel netdevices (through `ip tunnel change' as well as
`ip link set') lead to NETDEV_CHANGE being generated on the tunnel
device. Because what is relevant for the tunnel in question depends on
the tunnel type, handling of the event is dispatched to the IPIP module
through a newly-added interface mlxsw_sp_ipip_ops.ol_netdev_change().
IPIP tunnels now remember the last set of tunnel parameters in struct
mlxsw_sp_ipip_entry.parms, and use it to figure out what exactly has
changed.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a bound device of a tunnel netdevice changes VRF, the loopback RIF
that backs the tunnel needs to be updated and existing encapsulating
routes need to be refreshed.
Note that several tunnels can share the same bound device, in which case
all the impacted tunnels need to be updated.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The approach for offloading IP tunnels implemented currently by mlxsw
doesn't allow two tunnels that have the same local IP address in the
same (underlay) VRF. Previously, offloads were introduced on demand as
encap routes were formed. When such a route was created that would cause
offload of a conflicting tunnel, mlxsw_sp_ipip_entry_create() would
detect it and return -EEXIST, which would propagate up and cause FIB
abort.
Now however IPIP entries are created as soon as an offloadable netdevice
is created, and the failure prevents creation of such device.
Furthermore, if the driver is installed at the point where such
conflicting tunnels exist, the failure actually prevents successful
modprobe.
Furthermore, follow-up patches implement handling of NETDEV_CHANGE due
to the local address change. However, NETDEV_CHANGE can't be vetoed. The
failure merely means that the offloads weren't updated, but the change
in Linux configuration is not rolled back. It is thus desirable to have
a robust way of handling these conflicts, which can later be reused for
handling NETDEV_CHANGE as well.
To fix this, when a conflicting tunnel is created, instead of failing,
simply pull the old tunnel to slow path and reject offloading the
new one.
Introduce two functions: mlxsw_sp_ipip_entry_demote_tunnel() and
mlxsw_sp_ipip_demote_tunnel_by_saddr() to handle this. Make them both
public, because they will be useful later on in this patchset.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When trying to determine whether there are other offloaded tunnels with
the same local address, mlxsw_sp_ipip_entry_create() should look for a
tunnel with matching UL protocol, matching saddr, in the same VRF.
However instead of taking into account the UL protocol of the tunnel
netdevice (which mlxsw_sp_ipip_entry_saddr_matches() then compares to
the UL protocol of inspected IPIP entry), it deduces the UL protocol
from the inspected IPIP entry (and that's compared to itself).
This is currently immaterial, because only one tunnel type is offloaded,
and therefore the UL protocol always matches, but introducing support
for a tunnel with IPv6 underlay would uncover this error.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The work that needs to be done to update HW configuration in response to
changes is similar to what __mlxsw_sp_ipip_entry_update_tunnel() already
does, but with a number of twists: each change requires a different
subset of things to happen. Extend the function to support all these
uses, and allow finely-grained configuration of what should happen at
each call through a suite of function arguments.
Publish the updated function to allow use from the spectrum_ipip module.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The work that's done by mlxsw_sp_netdevice_ipip_ol_vrf_event() is a good
basis for a more versatile function that would take care of all sorts of
tunnel updates requests: __mlxsw_sp_ipip_entry_update_tunnel(). Extract
that function. Factor out a helper mlxsw_sp_ipip_entry_ol_lb_update() as
well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_rif_create() takes an extack parameter. So far,
for creation of loopback interfaces, NULL was passed. For some events
however the extack can be extracted and passed along. So do that for
NETDEV_CHANGEUPPER handler.
Use the opportunity to update the type of info argument that
mlxsw_sp_netdevice_ipip_ol_event() takes. Follow-up patches will
introduce handling of more changes, and some of them carry an extack as
well, but in an info structure of a different type. Though not strictly
erroneous (the pointer could be cast whichever way), it makes no sense
to pretend the value is always of a certain type, when in fact it isn't.
So change the prototype of the above-mentioned function as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The piece of logic to promote decap route, if any, is useful for generic
tunnel updates, not just for handling of NETDEV_UP events on tunnel
interfaces. Extract it to a separate function.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function only ever returns 0, so don't pretend it returns anything
useful and just make it void.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To implement NETDEV_CHANGE notifications on IP-in-IP tunnels, the
handler needs to figure out what actually changed, to understand how
exactly to update the offloads. It will do so by storing struct
ip_tunnel_parm with previous configuration, and comparing that to the
new version.
To facilitate these comparisons, extract the code that operates on
struct ip_tunnel_parm from the existing accessor functions, and make
those a thin wrapper that extracts tunnel parameters and dispatches.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These functions ideologically belong to the IPIP module, and some
follow-up work will benefit from their presence there.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the code down the road needs this logic as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To distinguish between events related to tunnel device itself and its
bound device, rename a number of functions related to handling tunneling
netdevice events to include _ol_ (for "overlay") in the name. That
leaves room in the namespace for underlay-related functions, which would
have _ul_ in the name.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sure the device and the kernel are performing the multipath hash
according to the same parameters by updating the device whenever the
relevant netevent is generated.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we used the hardware's defaults for multipath hash
computation. This patch aligns the hardware's multipath parameters with
the kernel's.
For IPv4 packets, the parameters are determined according to the
'fib_multipath_hash_policy' sysctl during module initialization. In case
L3-mode is requested, only the source and destination IP addresses are
used. There is no special handling of ICMP error packets.
In case L4-mode is requested, a 5-tuple is used: source and destination
IP addresses, source and destination ports and IP protocol. Note that
the layer 4 fields are not considered for fragmented packets.
For IPv6 packets, the source and destination IP addresses are used, as
well as the flow label and the next header fields.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RECRv2 register is used for setting up the router's ECMP hash
configuration.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct containing the work item queued from the netevent handler is
named after the only event it is currently used for, which is neighbour
updates.
Use a more appropriate name for the struct, as we are going to use it
for more events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to need to respond to netevents notifying us about
multipath hash updates by configuring the device's hash parameters.
Embed the netevent notifier in the router struct so that we could
retrieve it upon notifications and use it to configure the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This restores the original behaviour before the block callbacks were
introduced. Allow the drivers to do binding of block always, no matter
if the NETIF_F_HW_TC feature is on or off. Move the check to the block
callback which is called for rule insertion.
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smooth Cong Wang's bug fix into 'net-next'. Basically put
the bulk of the tcf_block_put() logic from 'net' into
tcf_block_put_ext(), but after the offload unbind.
Signed-off-by: David S. Miller <davem@davemloft.net>
It fixes a problem for the last chunk where 'chunk_size' is smaller than
MLXSW_I2C_BLK_MAX and data is copied to the wrong offset, overriding
previous data.
Fixes: 6882b0aee1 ("mlxsw: Introduce support for I2C bus")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ASIC has the ability to generate events whenever a sensor indicates
the temperature goes above or below its high or low thresholds,
respectively.
In new firmware versions the firmware enforces a minimum of 5
degrees Celsius difference between both thresholds. Make the driver
conform to this requirement.
Note that this is required even when the events are disabled, as in
certain systems interrupts are generated via GPIO based on these
thresholds.
Fixes: 85926f8770 ("mlxsw: reg: Add definition of temperature management registers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a FIB rule on a spectrum platform silently aborts FIB offload:
$ ip ru add pref 99 from all to 192.168.1.1 table 10
$ dmesg -c
[ 623.144736] mlxsw_spectrum 0000:03:00.0: FIB abort triggered. Note that FIB entries are no longer being offloaded to this device.
This patch reworks FIB rule handling to return a message to the user:
$ ip ru add pref 99 from all to 8.8.8.8 table 11
Error: spectrum: FIB rules not supported. Aborting offload.
spectrum currently only checks whether the fib rule is a default rule or
an l3mdev rule, both of which it knows how to handle. Any other it aborts
FIB offload. Move the processing to check the rule type inline with the
user request. If the rule is an unsupported one, then a work queue entry
is used to abort the offload. Change the rule delete handling to just
return since it does nothing at the moment.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace recurring magic number in PPCNT register with a define.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the HW stats cache to be local. Rename it for better clarity.
It holds the results of the last result of HW stats that are being read
periodically, in order to have answer for stats request immediately.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the spectrum_mr_tcam.c include the spectrum_mr_tcam.h header file.
Cleans up sparse warning:
symbol 'mlxsw_sp_mr_tcam_ops' was not declared. Should it be static?
Fixes: 0e14c7777a ("mlxsw: spectrum: Add the multicast routing hardware logic")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is only used internally in spectrum_mr.c and is not declared
in the header file, thus make it static.
Cleans up sparse warning:
symbol 'mlxsw_sp_mr_dev_vif_lookup' was not declared. Should it be static?
Fixes: c011ec1bbf ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix various endianness issues in comparisons and assignments. The fix is
entirely cosmetic as all the values fixed are endianness-agnostic.
Cleans up sparse warnings:
spectrum_mr.c:156:49: warning: restricted __be32 degrades to integer
spectrum_mr.c:206:26: warning: restricted __be32 degrades to integer
spectrum_mr.c:212:31: warning: incorrect type in assignment (different
base types)
spectrum_mr.c:212:31: expected restricted __be32 [usertype] addr4
spectrum_mr.c:212:31: got unsigned int
spectrum_mr.c:214:32: warning: incorrect type in assignment (different
base types)
spectrum_mr.c:214:32: expected restricted __be32 [usertype] addr4
spectrum_mr.c:214:32: got unsigned int
spectrum_mr.c:461:16: warning: restricted __be32 degrades to integer
spectrum_mr.c:461:49: warning: restricted __be32 degrades to integer
Fixes: c011ec1bbf ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the dump the per netlink packet entry counter should be zeroed out
when new packet is created.
Fixes: 190d38a52a ("mlxsw: spectrum_dpipe: Add support for adjacency table dump")
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reported-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KVD linear is currently partitioned into two partitions. One for
single entries and another for groups of 32 entries.
Add another partition consisting of groups of 512 entries which will
allow us to more accurately represent the nexthop weights in non-equal
cost multi-path routing.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory region where adjacency entries (nexthops) are stored is
called the KVD linear and is configured during initialization with a
size of 64K.
Extend this area with 32K more entries, that will be partitioned into 64
groups of 0.5K entries, thereby allowing us to support weighted nexthops
with high accuracy.
Change the ratio between both types of hash entries, so as to prevent
reduction in the number of double hash entries, which are used for IPv6
neighbours and routes with a prefix length greater than 64.
Note that the user will be able to control all these sizes once the
devlink resource manager is introduced.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the driver assumed all the nexthops have an equal weight
and wrote each to a single adjacency entry.
This patch takes the `weight` parameter into account and populates the
adjacency group according to the relative weight of each nexthop.
Specifically, the weights of all the nexthops that should be offloaded
are first normalized and then used to calculate the upper adjacency
index of each nexthop. This is done according to the hash-threshold
algorithm used by the kernel for IPv4 multi-path routing.
Adjacency groups are currently limited to 32 entries which limits the
weights that can be used, but follow-up patches will introduce groups of
512 entries.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device has certain restrictions regarding the size of an adjacency
group.
Have the router determine the size of the adjacency group according to
available KVDL allocation sizes and these restrictions.
This was not needed until now since only allocations of up 32 entries
were supported and these are all valid sizes for an adjacency group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the first step towards non-equal-cost multi-path support, store each
nexthop's weight.
For IPv6 nexthops always set the weight to 1, as it only supports ECMP.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current KVDL allocation API allows the user to specify the requested
number of entries, but the user has no way of knowing how many entries
were actually allocated.
This works because existing users (e.g., router) request the exact
number they end up using. With the introduction of large adjacency
groups, this will change, as the router will have the ability to choose
from several allocation sizes, where larger allocations provide higher
accuracy with respect to requested weights and better resilience against
nexthop failures.
One option is to have the router try several allocations of descending
size until one succeeds, but a better way is to simply allow it to query
the actual allocation size and then size its request accordingly.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KVD linear (KVDL) allocator currently consists of a very large
bitmap that reflects the KVDL's usage. The boundaries of each partition
as well as their allocation size are represented using defines.
This representation requires us to patch all the functions that act on a
partition whenever the partitioning scheme is changed. In addition, it
does not enable the dynamic configuration of the KVDL using the
up-coming resource manager.
Add objects to represent these partitions as well as the accompanying
code that acts on them to perform allocations and de-allocations.
In the following patches, this will allow us to easily add another
partition as well as new operations to act on these partitions.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adjacency group size is part of the match on the adjacency group and
should therefore be exposed using dpipe.
When non-equal-cost multi-path support will be introduced, the group's
size will help users understand the exact number of adjacency entries
each nexthop occupies, as a nexthop will no longer correspond to a
single entry.
The output for a multi-path route with two nexthops, one with weight 255
and the second 1 will be:
Example:
$ devlink dpipe table dump pci/0000:01:00.0 name mlxsw_adj
pci/0000:01:00.0:
index 0
match_value:
type field_exact header mlxsw_meta field adj_index value 65536
type field_exact header mlxsw_meta field adj_size value 512
type field_exact header mlxsw_meta field adj_hash_index value 0
action_value:
type field_modify header ethernet field destination mac value e4:1d:2d:a5:f3:64
type field_modify header mlxsw_meta field erif_port mapping ifindex mapping_value 3 value 1
index 1
match_value:
type field_exact header mlxsw_meta field adj_index value 65536
type field_exact header mlxsw_meta field adj_size value 512
type field_exact header mlxsw_meta field adj_hash_index value 510
action_value:
type field_modify header ethernet field destination mac value e4:1d:2d:a5:f3:65
type field_modify header mlxsw_meta field erif_port mapping ifindex mapping_value 4 value 2
Thus, the first nexthop occupies 510 adjacency entries and the second 2,
which leads to a ratio of 255 to 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were quite a few overlapping sets of changes here.
Daniel's bug fix for off-by-ones in the new BPF branch instructions,
along with the added allowances for "data_end > ptr + x" forms
collided with the metadata additions.
Along with those three changes came veritifer test cases, which in
their final form I tried to group together properly. If I had just
trimmed GIT's conflict tags as-is, this would have split up the
meta tests unnecessarily.
In the socketmap code, a set of preemption disabling changes
overlapped with the rename of bpf_compute_data_end() to
bpf_compute_data_pointers().
Changes were made to the mv88e6060.c driver set addr method
which got removed in net-next.
The hyperv transport socket layer had a locking change in 'net'
which overlapped with a change of socket state macro usage
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum tunnels do not default to ttl of "inherit" like the Linux ones
do. Configure TIGCR on router init so that the TTL of tunnel packets is
copied from the overlay packets.
Fixes: ee954d1a91 ("mlxsw: spectrum_router: Support GRE tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIGCR register is used for setting up the IPinIP Tunnel
configuration.
Fixes: ee954d1a91 ("mlxsw: spectrum_router: Support GRE tunnels")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers are converted to use block callbacks for TC_SETUP_CLS*.
So it is now safe to remove the calls to ndo_setup_tc from cls_*
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the newly introduced block callback infrastructure and
convert ndo_setup_tc calls for matchall and flower offloads to block
callbacks.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use container_of to convert the generic fib_notifier_info into
the event specific data structure.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack argument down to mlxsw_sp_rif_create and mlxsw_sp_vr_create
to set an error message on RIF or VR overflow. Now on overflow of
either resource the user gets an informative message as opposed to
failing with EBUSY.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for inetaddr_validator and inet6addr_validator. The
notifiers provide a means for validating ipv4 and ipv6 addresses
before the addresses are installed and on failure the error
is propagated back to the user.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an EMAD is transmitted, a timeout work item is scheduled with a
delay of 200ms, so that another EMAD will be retried until a maximum of
five retries.
In certain situations, it's possible for the function waiting on the
EMAD to be associated with a work item that is queued on the same
workqueue (`mlxsw_core`) as the timeout work item. This results in
flushing a work item on the same workqueue.
According to commit e159489baa ("workqueue: relax lockdep annotation
on flush_work()") the above may lead to a deadlock in case the workqueue
has only one worker active or if the system in under memory pressure and
the rescue worker is in use. The latter explains the very rare and
random nature of the lockdep splats we have been seeing:
[ 52.730240] ============================================
[ 52.736179] WARNING: possible recursive locking detected
[ 52.742119] 4.14.0-rc3jiri+ #4 Not tainted
[ 52.746697] --------------------------------------------
[ 52.752635] kworker/1:3/599 is trying to acquire lock:
[ 52.758378] (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c4fa4>] flush_work+0x3a4/0x5e0
[ 52.767837]
but task is already holding lock:
[ 52.774360] (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[ 52.784495]
other info that might help us debug this:
[ 52.791794] Possible unsafe locking scenario:
[ 52.798413] CPU0
[ 52.801144] ----
[ 52.803875] lock(mlxsw_core_driver_name);
[ 52.808556] lock(mlxsw_core_driver_name);
[ 52.813236]
*** DEADLOCK ***
[ 52.819857] May be due to missing lock nesting notation
[ 52.827450] 3 locks held by kworker/1:3/599:
[ 52.832221] #0: (mlxsw_core_driver_name){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[ 52.842846] #1: ((&(&bridge->fdb_notify.dw)->work)){+.+.}, at: [<ffffffff811c65c4>] process_one_work+0x7d4/0x12f0
[ 52.854537] #2: (rtnl_mutex){+.+.}, at: [<ffffffff822ad8e7>] rtnl_lock+0x17/0x20
[ 52.863021]
stack backtrace:
[ 52.867890] CPU: 1 PID: 599 Comm: kworker/1:3 Not tainted 4.14.0-rc3jiri+ #4
[ 52.875773] Hardware name: Mellanox Technologies Ltd. "MSN2100-CB2F"/"SA001017", BIOS 5.6.5 06/07/2016
[ 52.886267] Workqueue: mlxsw_core mlxsw_sp_fdb_notify_work [mlxsw_spectrum]
[ 52.894060] Call Trace:
[ 52.909122] __lock_acquire+0xf6f/0x2a10
[ 53.025412] lock_acquire+0x158/0x440
[ 53.047557] flush_work+0x3c4/0x5e0
[ 53.087571] __cancel_work_timer+0x3ca/0x5e0
[ 53.177051] cancel_delayed_work_sync+0x13/0x20
[ 53.182142] mlxsw_reg_trans_bulk_wait+0x12d/0x7a0 [mlxsw_core]
[ 53.194571] mlxsw_core_reg_access+0x586/0x990 [mlxsw_core]
[ 53.225365] mlxsw_reg_query+0x10/0x20 [mlxsw_core]
[ 53.230882] mlxsw_sp_fdb_notify_work+0x2a3/0x9d0 [mlxsw_spectrum]
[ 53.237801] process_one_work+0x8f1/0x12f0
[ 53.321804] worker_thread+0x1fd/0x10c0
[ 53.435158] kthread+0x28e/0x370
[ 53.448703] ret_from_fork+0x2a/0x40
[ 53.453017] mlxsw_spectrum 0000:01:00.0: EMAD retries (2/5) (tid=bf4549b100000774)
[ 53.453119] mlxsw_spectrum 0000:01:00.0: EMAD retries (5/5) (tid=bf4549b100000770)
[ 53.453132] mlxsw_spectrum 0000:01:00.0: EMAD reg access failed (tid=bf4549b100000770,reg_id=200b(sfn),type=query,status=0(operation performed))
[ 53.453143] mlxsw_spectrum 0000:01:00.0: Failed to get FDB notifications
Fix this by creating another workqueue for EMAD timeouts, thereby
preventing the situation of a work item trying to flush a work item
queued on the same workqueue.
Fixes: caf7297e7a ("mlxsw: core: Introduce support for asynchronous EMAD register access")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Formerly, IPIP entries were created lazily by next hops that referenced
an offloadable IP-in-IP netdevice. However now that they are created
eagerly as a reaction to events on such netdevices, the reference
counting is useless. Hence drop it.
The routes whose next hops reference an offloaded IP-in-IP netdevice
actually linger around a bit after their device is unregistered.
However, mlxsw_sp_ipip_entry_destroy() also destroys the backing
loopback, and mlxsw_sp_rif_destroy() transitively (via
mlxsw_sp_nexthop_rif_gone_sync()) calls mlxsw_sp_nexthop_ipip_fini(),
which unlinks the IPIP entry from a next hop. Thus no dangling pointers
are left behind for the brief window after netdevice is gone, but routes
not yet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPIP entries are created as soon as an offloadable device is created.
That means that when such a device is later moved to a different VRF,
the loopback device that backs the tunnel is wrong.
Thus when an offloadable encapsulating netdevice moves from one VRF to
another, make sure that the loopback is updated as necessary.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code for offloading IP-in-IP tunneling assumes that there is no
decap without encap. But that's never true for IPv6 overlays, and is not
true for IPv4 ones either, if net.ipv4.conf.*.rp_filter is unset.
To support decap-only tunnels, an IPIP entry is now created as soon as
an offloadable tunneling device is created. When that netdevice is up'd,
a decap route is looked up and possibly offloaded. Thus decap is not
handled implicitly as part of mlxsw_sp_ipip_entry_get() call anymore,
but needs to be done explicitly after the get, if desired.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far, all netdevice notifications that the driver cared about were
related to its own ports, and mlxsw_sp could be retrieved from the
netdevice's private data. For IP-in-IP offloading however, the driver
cares about events on foreign netdevices, and getting at mlxsw_sp or
router data structures from the handler is inconvenient.
Therefore move the netdevice notifier blocks from global scope to struct
mlxsw_sp to allow retrieval from the notifier block pointer itself.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support the SWITCHDEV_ATTR_ID_BRIDGE_MROUTER port attribute switchdev
notification.
To do that, add the mrouter flag to struct mlxsw_sp_bridge_device, which
indicates whether the bridge device was set to be mrouter port. This field
is set when:
- A new bridge is created, where the value is taken from the kernel
bridge value.
- A switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER notification is sent.
In addition, change the bridge MID entries to include the router port when
the bridge device is configured to be mrouter port. The MID entries are
updated in the following cases:
- When a new MID entry is created, update the router port according to the
bridge mrouter state.
- When a SWITCHDEV_ATTR_ID_BRIDGE_MROUTER notification is sent, update all
the bridge's MID entries.
This is aligned with the case where a bridge slave is configured to be
mrouter port.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum, MDB entries point to MID entries, that indicate which ports a
packet should be forwarded to. Add the support in creating MID entries that
forward the packet to the Spectrum router port.
This will be later used to handle the bridge mrouter port switchdev
notifications.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum hardware, the router port is a virtual port that is the gateway
to the routing mechanism. Hence, in order for a packet to be L3 forwarded,
it must first be L2 forwarded to the router port inside the hardware.
Further patches in this patchset are going to introduce support in bridge
device used as an mrouter port. In this case, the router port index will be
needed in order to update the MDB entries to include the router port. Thus,
export the mlxsw_sp_router_port function, which returns the index of the
Spectrum router port.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that actually takes care of bridge offload introduces a few
more non-trivial constraints with regards to bridge enslavements.
Propagate extack there to indicate the reason.
$ ip link add link enp1s0np1 name enp1s0np1.10 type vlan id 10
$ ip link add link enp1s0np1 name enp1s0np1.20 type vlan id 20
$ ip link add name br0 type bridge
$ ip link set dev enp1s0np1.10 master br0
$ ip link set dev enp1s0np1.20 master br0
Error: spectrum: Can not bridge VLAN uppers of the same port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to physical ports, enslavement of VLAN devices can also fail.
Use extack to indicate why the enslavement failed.
$ ip link add link enp1s0np1 name enp1s0np1.10 type vlan id 10
$ ip link add name bond0 type bond mode 802.3ad
$ ip link set dev enp1s0np1.10 master bond0
Error: spectrum: VLAN devices only support bridge and VRF uppers.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit fc922bb0dd ("mlxsw: spectrum_router: Use one LPM tree for
all virtual routers") I increased the scale of supported VRFs by having
all of them share the same LPM tree.
In order to avoid look-ups for prefix lengths that don't exist, each
route removal would trigger an aggregation across all the active virtual
routers to see which prefix lengths are in use and which aren't and
structure the tree accordingly.
With the way the data structures are currently laid out, this is a very
expensive operation. When preformed repeatedly - due to the invocation
of the abort mechanism - and with enough VRFs, this can result in a hung
task.
For now, avoid this optimization until it can be properly re-added in
net-next.
Fixes: fc922bb0dd ("mlxsw: spectrum_router: Use one LPM tree for all virtual routers")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: David Ahern <dsa@cumulusnetworks.com>
Tested-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw fails device enslavement for a number of reasons. Use the extack
facility to return an error message to the user stating why the enslave
is failing.
Messages are prefixed with "spectrum" so users know it is a constraint
imposed by the hardware driver. For example:
$ ip li add br0.11 link br0 type vlan id 11
$ ip li set swp11 master br0
Error: spectrum: Enslaving a port to a device that already has an upper device is not supported.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally return success if the kmalloc_array() call fails.
Fixes: 0e14c7777a ("mlxsw: spectrum: Add the multicast routing hardware logic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw_afa_block_create() doesn't return error pointers, it returns NULL
on error.
Fixes: 0e14c7777a ("mlxsw: spectrum: Add the multicast routing hardware logic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the support of trap-and-forward route action in the multicast routing
offloading logic. A route will be set to trap-and-forward action if one (or
more) of its output interfaces is not offload-able, i.e. does not have a
valid Spectrum RIF.
This way, a route with mixed output VIFs list, which contains both
offload-able and un-offload-able devices can go through partial offloading
in hardware, and the rest will be done in the kernel ipmr module.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition to the current multicast route actions, which include trap
route action and a forward route action, add the trap-and-forward multicast
route action, and implement it in the multicast routing hardware logic.
To implement that, add a trap-and-forward ACL action as the last action in
the route flexible action set. The used trap is the ACL2 trap, which marks
the packets with offload_mr_forward_mark, to prevent the packet from being
forwarded again by the kernel.
Note: At that stage the offloading logic does not support trap-and-forward
multicast routes. This patch adds the support only in the hardware logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a multicast route is configured with trap-and-forward action, the
packets should be marked with skb->offload_mr_fwd_mark, in order to prevent
the packets from being forwarded again by the kernel ipmr module.
Due to this, it is not possible to use the already existing multicast trap
(MLXSW_TRAP_ID_ACL1) as the packet should be marked differently. Add the
MLXSW_TRAP_ID_ACL2 which is for trap-and-forward multicast routes, and set
the offload_mr_fwd_mark skb field in its handler.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use trap/discard flex action to implement trap and forward. The action will
later be used for multicast routing, as the multicast routing mechanism is
done using ACL flexible actions in Spectrum hardware. Using that action, it
will be possible to implement a trap-and-forward route.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When considering whether to set RTNH_F_OFFLOAD flag on an IPv6 route,
mlxsw_sp_fib6_entry_offload_set() looks up the mlxsw_sp_nexthop
corresponding to a given route, and decides based on whether the next
hop's offloaded flag was set. When looking for the matching next hop, it
also takes into account the device of the route, which must match next
hop's RIF.
IPIP next hops however hitherto didn't set the RIF. As a result, IPv6
routes forwarding traffic to IP-in-IP netdevices are never marked as
offloaded, even when they actually are.
Thus track RIF of IPIP next hops the same way as that of ETHERNET next
hops.
Fixes: 8f28a30976 ("mlxsw: spectrum_router: Support IPv6 overlay encap")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating a new RIF, bumping RIF count of the containing VR is the
last thing to be done. Symmetrically, when destroying a RIF, RIF count
is first dropped and only then the rest of the cleanup proceeds.
That's a problem for loopback RIFs. Those hold two VR references: one
for overlay and one for underlay. mlxsw_sp_rif_destroy() releases the
overlay one, and the deconfigure() callback the underlay one. But if
both overlay and underlay are the same, and if there are no other
artifacts holding the VR alive, this put actually destroys the VR. Later
on, when mlxsw_sp_rif_destroy() calls mlxsw_sp_vr_put() for the same VR,
the VR will already have been released and the kernel crashes with NULL
pointer dereference.
The underlying problem is that the RIF under destruction ends up
referencing the overlay VR much longer than it claims: all the way until
the call to mlxsw_sp_vr_put(). So line up the reference counting
properly to reflect this. Make corresponding changes in
mlxsw_sp_rif_create() as well for symmetry.
Fixes: 6ddb7426a7 ("mlxsw: spectrum_router: Introduce loopback RIFs")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the unlikely event that mfc->mfc_un.res.ttls[i] is 255 for all
values of i from 0 to MAXIVS-1, the err is not set at all and hence
has a garbage value on the error return at the end of the function,
so initialize it to 0. Also, the error return check on err and goto
to err: inside the for loop makes it impossible for err to be zero
at the end of the for loop, so we can remove the redundant err check
at the end of the loop.
Detected by CoverityScan CID#1457207 ("Unitialized scalar value")
Fixes: c011ec1bbf ("mlxsw: spectrum: Add the multicast routing offloading logic")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the Spectrum router logic not ignore the RTNL_FAMILY_IPMR FIB
notifications.
Past commits added the IPMR VIF and MFC add/del notifications via the
fib_notifier chain. In addition, a code for handling these notifications in
the Spectrum router logic was added. Make the Spectrum router logic not
ignore these notifications and forward the requests to the Spectrum
multicast router offloading logic.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the fact that multicast routes hold the minimum MTU of all the
egress RIFs and trap packets that don't meet it, notify the mulitcast
router code on RIF MTU changes.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functionality for calling the multicast routing offloading logic upon
MFC and VIF add and delete notifications. In addition, call the multicast
routing upon RIF addition and deletion events.
As the multicast routing offload logic may sleep, the actual calls are done
in a deferred work. To ensure the MFC object is not freed in that interval,
a reference is held to it. In case of a failure, the abort mechanism is
used, which ejects all the routes from the hardware and triggers the
traffic to flow through the kernel.
Note: At that stage, the FIB notifications are still ignored, and will be
enabled in a further patch.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the mlxsw Spectrum driver offloads only either the RT_TABLE_MAIN
FIB table or the VRF tables, so the RT_TABLE_LOCAL table is squashed to the
RT_TABLE_MAIN table to allow local routes to be offloaded too.
By default, multicast MFC routes which are not assigned to any user
requested table are put in the RT_TABLE_DEFAULT table.
Due to the fact that offloading multicast MFC routes support in Spectrum
router logic is going to be introduced soon, squash the default table to
MAIN too.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the multicast routing hardware API introduced in previous patch
for the specific spectrum hardware.
The spectrum hardware multicast routes are written using the RMFT2 register
and point to an ACL flexible action set. The actions used for multicast
routes are:
- Counter action, which allows counting bytes and packets on multicast
routes.
- Multicast route action, which provide RPF check and do the actual packet
duplication to a list of RIFs.
- Trap action, in the case the route action specified by the called is
trap.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the multicast router offloading logic, which is in charge of handling
the VIF and MFC notifications and translating it to the hardware logic API.
The offloading logic has to overcome several obstacles in order to safely
comply with the kernel multicast router user API:
- It must keep track of the mapping between VIFs to netdevices. The user
can add an MFC cache entry pointing to a VIF, delete the VIF and add
re-add it with a different netdevice. The offloading logic has to handle
this in order to be compatible with the kernel logic.
- It must keep track of the mapping between netdevices to spectrum RIFs,
as the current hardware implementation assume having a RIF for every
port in a multicast router.
- It must handle routes pointing to pimreg device to be trapped to the
kernel, as the packet should be delivered to userspace.
- It must handle routes pointing tunnel VIFs. The current implementation
does not support multicast forwarding to tunnels, thus routes that point
to a tunnel should be trapped to the kernel.
- It must be aware of proxy multicast routes, which include both (*,*)
routes and duplicate routes. Currently proxy routes are not offloaded
and trigger the abort mechanism: removal of all routes from hardware and
triggering the traffic to go through the kernel.
The multicast routing offloading logic also updates the counters of the
offloaded MFC routes in a periodic work.
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate error instead of doing WARN_ON right away.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for controlling nexthop counters via dpipe.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for adjacency table dump.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting counters on nexthops based on dpipe's adjacency
table counter status. This patch also adds the ability for getting the
counter value, which will be used by the dpipe adjacency table dump
implementation in the next patches.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to add the ability for setting counters on nexthops the RATR
register should be extended.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add initial support for router adjacency table. The table does lookup
based on the nexthop-group index and the local nexthop offset. After
locating the nexthop entry it sets the destination MAC address and the
egress RIF.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation before introducing the ability to dump the
adjacency table via dpipe, and to count the table size. The current table
implementation avoids tunnel entries, thus a helper for checking if
the nexthop group contains tunnel entries is also provided. The mlxsw's
nexthop representative struct stays private to the router module.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use list_is_last helper to check for last neighbor.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep nexthops in a linked list for easy access.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds field for mlxsw's meta header which will be used to
describe the match/action behavior of the adjacency table.
The fields are:
1. Adj_index - The global index of the nexthop group in the adjacency
table.
2. Adj_hash_index - Local index offset which is based on packets hash
mod the nexthop group size.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix indentation in mlxsw_meta header's description.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a mrouter is registered or leaves a mid, don't update the HW.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mdb flush the port is being removed from all the mids it is registered
to. But if the port is mrouter, all the mids floods to it.
This patch remove mrouter ports from mids it is not registered to in the
mdb flush.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whenever a port starts / stops being mrouter, update all the mdb entries
in the HW to flood / stop flooding mc packets there.
The change should happen only if the port is not in the mid. (If it is,
the mid should flood mc packets to this port anyway)
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When mc is enabled, whenever a mc packet doesn't hit any mdb entry it is
being flood to the ports marked as mrouters. However, all mc packets should
be flooded to them even if they match an entry in the mdb.
This patch adds the mrouter ports to every mdb entry that is being written
to the HW.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is being removed from a bridge, flush the bridge mdb to remove
the mids of that port.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multicast is disabled, flood mc packets only to port that are marked
BR_MCAST_FLOOD (instead to all).
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the generic mc flood function to decide whether to flood mc to a port
when mc is being enabled / disabled.
Move this function in the file to avoid forward declaration.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove all the mdb entries from the HW when mc is being disabled and
re-write them when it is being enabled.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't write multicast related data to the HW when mc is disabled.
Also, don't allocate mid id to new mids (so the remove function could know
that they weren't wrote to the HW)
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break mid deletion into two function, so it will be possible in the future
to delete a mid entry for other reasons then switchdev command (like port
deletion).
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attach mid getting and releasing mid id to the HW write / remove, and add
a flag to indicate whether the mid is in the HW. It is done because mid id
is also HW index to this mid.
This change allows adding in the following patches the ability to have a
mid in the mdb cache but not in the HW. It will be useful for being able
to disable the multicast.
It means that the mdb is being written / delete to the HW in the mid
allocation / removing function, not after them.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break the smid write function into two, one that cleans the ports that
might be still written there and one that changes an exiting mid entry.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of saving all the mids in the same list, save them per vlan
device. This change allows a more efficient mid find.
Also, in the next patches, there will be added a lot of loops over all the
mids in bridge device for multicast disable, mrouter change and ndb flush.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
