This is a patch for adding gpio control about enable/disable of buck.
Signed-off-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a patch for fixing unmatched of_node.
Signed-off-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When drivers use simplified DT parsing method (they provide
'regulator_desc.of_match') they still may want to parse custom
properties for some of the regulators. For example some of the
regulators support GPIO enable control.
Add a driver-supplied callback for such case. This way the regulator
core parses common bindings offloading a lot of code from drivers and
still custom properties may be used.
The callback, called for each parsed regulator, may modify the
'regulator_config' initially passed to regulator_register().
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drivers can use the of_regulator_match() function to parse the regulator
init_data from DT. A match table is used to specify the name of the node
containing the regulators, the device node and to return the init_data
to the caller.
But also the static regulator descriptor is needed to correctly extract
some DT properties like the regulator initial and suspend modes. Use the
match table to pass that information.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The of_get_regulator_init_data() function is used to extract the regulator
init_data but information on how to extract certain data is defined in the
static regulator descriptor (e.g: how to map the hardware operating modes).
Add a const struct regulator_desc * parameter to the function signature so
the parsing logic could use the information in the struct regulator_desc.
of_get_regulator_init_data() relies on of_get_regulation_constraints() to
actually extract the init_data so it has to pass the struct regulator_desc
but that is modified on a later patch.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The "regulator-initial-mode" and "regulator-mode" DT properties allows
to configure the regulator operating modes at startup or when a system
enters into a susend state.
But these properties use as valid values the operating modes supported
by each device while the core deals with the standard operating modes.
So a mapping function is needed to translate from the hardware specific
modes to the standard ones.
This mapping is a non-varying configuration for each regulator, so add
a function pointer to struct regulator_desc that will allow drivers to
define their callback to do the modes translation.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a PRE_DISABLE notification so that consumers can use a
notifier to run any steps required to prepare for the
regulator being switched off. Since the regulator disable
can fail an abort notification is also added.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The user hasn't got a regulator and shouldn't be mislead into thinking
they have one; really we should probably remove this stub entirely (and
may well before the next merge window).
Signed-off-by: Mark Brown <broonie@kernel.org>
Most drivers do not set the ena_gpio field of struct regulator_config
before passing it to the regulator core. This is fine as long as the
gpio identifier that is passed is a positive integer. But the gpio
identifier 0 is also valid. So we are not able to decide wether we got a
real gpio identifier or not based on a 0 in ena_gpio.
To be able to decide if it is a valid gpio that got passed, this patch
adds a ena_gpio_initialized field that should be set if was initialized
with a correct value, either a gpio >= 0 or a negative error number. The
core then checks if ena_gpio or ena_gpio_initialized before handling it
as a gpio. This way we maintain backwards compatibility and fix the
behaviour for gpio number 0.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
sh:sh2007_defconfig fails to build with the following error:
In file included from include/linux/regulator/machine.h:18:0,
from arch/sh/boards/board-sh2007.c:10:
include/linux/regulator/consumer.h: In function 'regulator_get_optional':
include/linux/regulator/consumer.h:271:2:
error: implicit declaration of function 'ERR_PTR'
include/linux/err.h: At top level:
include/linux/err.h:23:35: error: conflicting types for 'ERR_PTR'
include/linux/regulator/consumer.h:271:9:
note: previous implicit declaration of 'ERR_PTR' was here
Since consumer.h uses ERR_PTR, it should include err.h.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently regulator drivers which support DT all repeat very similar code
to supply a list of known regulator identifiers to be matched with DT,
convert that to platform data which is then matched up with the regulators
as they are registered. This is both fiddly to get right and for devices
which can use the standard helpers to provide their operations is the main
source of code in the driver.
Since this code is essentially identical for most drivers we can factor it
out into the core, moving the identifiers in the match table into the
regulator descriptors and also allowing drivers to pass in the name of the
subnode to search. When a driver provides an of_match string for the
regulator the core will attempt to use that to obtain init_data, allowing
the driver to remove all explicit code for DT parsing and simply provide
data instead.
The current code leaks the phandles for the child nodes, this will be
addressed incrementally and makes no practical difference for FDT anyway
as the DT data structures are never freed.
Signed-off-by: Mark Brown <broonie@linaro.org>
Add device-tree support to max1586.
The driver can still be used with the legacy platform data, or the new
device-tree way.
This work is heavily inspired by the device-tree support of its cousin
max8660 driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some cases we need to know when a regulator is about to be changed.
Add a way for clients to be notified. Note that for set_voltage() we
don't necessarily know what voltage we'll end up with, so we tell the
client what the range will be so they can prepare.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie+linaro@kernel.org>
Fix kernel-doc warnings in regulator header files:
Warning(..//include/linux/regulator/machine.h:140): No description found for parameter 'ramp_disable'
Warning(..//include/linux/regulator/driver.h:279): No description found for parameter 'linear_ranges'
Warning(..//include/linux/regulator/driver.h:279): No description found for parameter 'n_linear_ranges'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a patch for supporting device tree of DA9211/DA9213.
Signed-off-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix below build warning:
CC [M] drivers/regulator/hi6421-regulator.o
drivers/regulator/hi6421-regulator.c:356:2: warning: initialization discards 'const' qualifier from pointer target type [enabled by default]
This is a revert of commit 716845ebeb ("regulator: core: Fix build error due
to const qualifier for ops"). The build error was fixed by commit 39f5460d7f
("regulator: core: add const to regulator_ops and fix build error in mc13892").
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop const qualifier for ops of struct regulator_desc.
Allow regulator drivers to update ops before registering regulator.
Fix below build error:
CC [M] drivers/regulator/mc13892-regulator.o
drivers/regulator/mc13892-regulator.c: In function 'mc13892_regulator_probe':
drivers/regulator/mc13892-regulator.c:586:3: error: assignment of member 'set_mode' in read-only object
drivers/regulator/mc13892-regulator.c:588:3: error: assignment of member 'get_mode' in read-only object
make[2]: *** [drivers/regulator/mc13892-regulator.o] Error 1
make[1]: *** [drivers/regulator] Error 2
make: *** [drivers] Error 2
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some regulator require a minimum delay between its disable and next enable.
This is to avoid damages when out-of-range frequent disable/enable of a
single regulator can bring to the regulator chip.
Add @off_on_delay to struct regulator_desc. Device drivers' can use this field
to set this guard time.
Add @last_off_jiffy to struct regulator_dev. When @off_on_delay is set by
driver, regulator core can store its last off (disable) time into this field.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
struct regulator_ops *ops is a member in struct regulator_desc, which gets
its value from individual regulator driver upon regulator_register() and
is used by regulator core APIs. It's not allowed for regulator core to
modify any of these callbacks in *ops. Add 'const' qualifier to enforce that.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add device id and definition of registers and regulators to support
the act8846 PMU.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch prepares support for other devices in the act88xx family of
PMUs manufactured by Active-Semi.
http://www.active-semi.com/products/power-management-units/act88xx/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add helper functions that allow regulator consumers to obtain low-level
details about the regulator hardware, like the voltage selector register
address and such. These details can be useful when configuring hardware
or firmware that want to do low-level access to regulators, with no
involvement from the kernel.
The use-case for Tegra is a voltage-controlled oscillator clocksource
which has control logic to change the supply voltage via I2C to achieve
a desired output clock rate.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is the driver for the Dialog DA9211 Multi-phase 12A DC-DC Buck
Converter regulator. It communicates via an I2C bus to the device.
Signed-off-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
CONFIG_REGULATOR_AB8500_DEBUG is always not defined.
ab8500_regulator_debug_init() is not called at all now,
ab8500_regulator_debug_exit() simply return 0, thus remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
When CONFIG_REGULATOR is not set, we cannot call
regulator_can_change_voltage() from a device driver, which results
in a build error like
video/fbdev/omap2/dss/hdmi5.c: In function 'hdmi_init_regulator':
video/fbdev/omap2/dss/hdmi5.c:149:2: error: implicit declaration of function 'regulator_can_change_voltage' [-Werror=implicit-function-declaration]
even for drivers that don't require the regulator API normally.
Such a use was recently added in the omap2+ hdmi driver.
This avoids the problem by adding a static inline function
stub in the API header, as we have for most of the other
regulator functions as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Mark Brown <broonie@kernel.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We already have dummy implementation for most of the regulators APIs for
!CONFIG_REGULATOR case and were missing it for regulator_set_voltage_time().
Found this issue while compiling cpufreq-cpu0 driver without regulators support
in kernel.
drivers/cpufreq/cpufreq-cpu0.c: In function ‘cpu0_cpufreq_probe’:
drivers/cpufreq/cpufreq-cpu0.c:186:3: error: implicit declaration of function ‘regulator_set_voltage_time’ [-Werror=implicit-function-declaration]
Fix this by adding dummy definition for regulator_set_voltage_time().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drivers that call regulator_get_optional are tolerant to the absence of
that regulator. By modifying the value returned from the stub function
to match that seen when a regulator isn't present, callers can wrap the
regulator logic with an IS_ERR based conditional even if they happen to
call regulator_is_supported_voltage. This improves efficiency as well
as eliminates the possibility for a very subtle bug.
Signed-off-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch extends the regulator helpers to account for device that use
multiple bits for control when using regmap enable/disable/bypass ops.
The actual regulator helpers wrongly assume that the regulator control
is always performed using single bits, using in the regulator_desc
struct only two parameters *_reg and *_mask defining register and mask
for control.
This patch extends this struct and introduces the helpers to take into
account devices where control is performed using multiple bits and
specific multi-bit values are used for enabling/disabling/bypassing the
regulator.
Signed-off-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
support pfuze200 chip which remove SW1C and SW4 based on pfuze100.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
These patches add the ability to create an alternative device on which
a lookup for a certain supply should be conducted.
A common use-case for this would be devices that are logically
represented as a collection of drivers within Linux but are are
presented as a single device from device tree. It this case it is
necessary for each sub device to locate their supply data on the main
device.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add REGULATOR_LINEAR_RANGE macro and convert regulator drivers to use it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
linear ranges means each range has linear voltage settings.
So we can calculate max_uV for each linear range in regulator core rather than
set the max_uV field in drivers.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The turn-on time of the regulator depends on the regulator device's
electrical characteristics. Sometimes regulator turn-on time also
depends on the capacitive load on the given platform and it can be
more than the datasheet value.
The driver provides the enable-time as per datasheet.
Add support for configure the enable ramp time through regulator
constraints so that regulator core can take this value for enable
time for that regulator.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix fatal kernel-doc error in <linux/regulator/driver.h>:
Error(include/linux/regulator/driver.h:52): cannot understand prototype: 'struct regulator_linear_range '
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
[Rewrote first line -- broonie]
Signed-off-by: Mark Brown <broonie@linaro.org>
No boards have used this functionality and the new default of providing
dummy regulators by default provides a better solution to the problem it
was trying to solve.
Signed-off-by: Mark Brown <broonie@linaro.org>
Many regulator drivers have a remove function that consists solely of
calling regulator_unregister() so provide a devm_regulator_register()
in order to allow this repeated code to be removed and help eliminate
error handling code.
Signed-off-by: Mark Brown <broonie@linaro.org>
If given rail has the single voltage (n_voltages = 1) then provide the
rail voltage through regulator descriptor so that core can use this
value for finding voltage.
This will avoid the implementation of the callback for get_voltage() or
list_voltage() callback on regulator driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a resource managed regulator_get_exclusive()
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add define for __FAN53555_H__ to prevent multiple include of the header file.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds devicetree bindings for max8660, along with some
documentation.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
While the majority of supplies on devices are mandatory and can't be
physically omitted for electrical reasons some devices do have optional
supplies and need to know if they are missing, MMC being the most common
of these.
Currently the core accurately reports all errors when regulators are
requested since it does not know if the supply is one that must be provided
even if by a regulator software does not know about or if it is one that
may genuinely be disconnected. In order to allow this behaviour to be
changed and stub regulators to be provided in the former case add a new
regulator request function regulator_get_optional() which provides a hint
to the core that the regulator may genuinely not be connected.
Currently the implementation is identical to the current behaviour, future
patches will add support in the core for returning stub regulators in the
case where normal regulator_get() fails and the board has requested it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Chris Ball <cjb@laptop.org>
Add pfuze100 regulator driver.
Signed-off-by: Robin Gong <b38343@freescale.com>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some hardwares support disabling ramp delay, so adding ramp_disable flag to
constraints. It will be used to figure out whether ramp_delay in constraints
is explicitly set to zero or its unintialized (zero by default).
And we don't need to call set_voltage_time_sel() for regulators for whom ramp
delay is disabled in constraints.
Signed-off-by: Yadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Many regulators have several linear ranges of selector with different
step sizes, for example offering better resolution at lower voltages.
Provide regulator_{map,list}_voltage_linear_range() allowing these
regulators to use generic code. To do so a table of regulator_linear_range
structs needs to be pointed to from the descriptor.
This was inspired by similar code included in a driver submission from
Chao Xie and Yi Zhang at Marvell.
Signed-off-by: Mark Brown <broonie@linaro.org>
The expected semantic for something expressed as a tolerance is that it
should deliver the specified value with some deviation allowed but this
is not what set_voltage_tol() currently does. Instead it just passes
the maximum possible range to set_voltage() which will typically result
in a voltage aimed at lower than the target voltage.
Instead first try to set a voltage between the target voltage and the
upper limit, then fall back on the full range. This will be much more
robust against physical variation in systems and makes the API behave
more like users would expect.
Signed-off-by: Mark Brown <broonie@linaro.org>
Some platforms don't support the AB8500 external regulators, so instead
of having a list of is_<platform>() calls prior to calling
ab8500_ext_regulator_init() from ab8500_regulator_probe(), we can only
register as a platform device on platforms which require them. It means
we also have more control over them when booting with Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonielinaro.org>
Add regulator_get_linear_step(), which returns the voltage step size
between VSEL values for linear regulators. This is intended for use
by regulator consumers which build their own voltage-to-VSEL tables.
Signed-off-by: Paul Walmsley <pwalmsley@nvidia.com>
Reviewed-by: Andrew Chew <achew@nvidia.com>
Cc: Matthew Longnecker <mlongnecker@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A lot of regulator hardware has ascendant voltage list.
This patch adds regulator_map_voltage_ascend() and export it.
Drivers that have ascendant voltage list can use this as their map_voltage()
operation, this is more efficient than default regulator_map_voltage_iterate()
function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ab8500_ext_regulator_exit() never fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds Device Tree support to max8952 regulator driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch modifies platform data structure of max8952 driver to
use pointer to regulator_init_data struct instead of embedding it.
This is a prerequisite for adding Device Tree support for the driver.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Introduce aux5, aux6 into ab8540 regulator framework.
Signed-off-by: Zhenhua HUANG <zhenhua.huang@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Maxime COQUELIN <maxime.coquelin@stericsson.com>
Reviewed-by: David PARIS <david.paris@stericsson.com>
Reviewed-by: Philippe LANGLAIS <philippe.langlais@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Before the AB8500 External Regulator driver was Mainlined, it used
to be conditionally compiled in using the CONFIG_REGULATOR_AB8500_EXT
flag. During the review process that capability was removed, but the
guard controlling prototyping slipped though the net. This patch
cleans it up.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To obtain full AB8540 regulator support, the AB8500 regulator driver
first needs to know its register layout and their initialisation values
for each. That information is provided via a couple of large data
structures which we provide here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To obtain full AB8505 regulator support, the AB8500 regulator driver
first needs to know its register layout and their initialisation values
for each. That information is provided via a couple of large data
structures which we provide here.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The purpose of this patch is to guarantee that ab8500-debug will
record the regulator registers before they are modified by the
ab8500 regulator driver.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The USB regulator is controlled by hardware. The software support
was only needed for early hardware (ED) which is no longer supported.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Support for HW request is added in the external regulator
driver. A flag in the board configuration can be set to
let HW control the regulator when there is no SW request.
This means that the regulator will be put in high power
mode when there is a SW request and in HW-request mode
otherwise.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Mattias NILSSON <mattias.i.nilsson@stericsson.com>
Reviewed-by: Jonas ABERG <jonas.aberg@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ABx500 is capable of controlling three external regulator supplies.
Most commonly on and off are supported, but if an external regulator
chipset or power supply supports high-power and low-power mode settings,
we can control those too.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Clean out initialisation that is handled by SoC. Regulator
settings for Vpll (partly), Vsmps1, Vsmps2, Vsmps3 (partly),
Vrf1, Varm, Vape, Vbb, Vmod are cleaned out. They should not
be touched by the kernel.
We also update many of the initialisation values to be more
in-line with the current development efforts of ST-Ericsson
internal engineers.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ab8500 MFD should not have knowledge about regulator-
specific platform data like number of regulators and
regulator registers. As the regulator platform data is
about to grow with external regulators, this information
is moved to a new structure provided by the regulator
driver.
Signed-off-by: Bengt Jonsson <bengt.g.jonsson@stericsson.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Yvan FILLION <yvan.fillion@stericsson.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
