Otherwise the DDI_A_4_LANES bit gets lost and we can't use > 2 lanes
on eDP. This fixes eDP on hsw with > 2 lanes.
Also s/port_reversal/saved_port_bits/ since the current name is
confusing.
Signed-off-by: Stéphane Marchesin <marcheu@chromium.org>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I.e. for letter/pillarboxing. For those cases we need to adjust the
mode a bit, but Jesse gmch pfit refactoring in
commit 2dd24552ca
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Apr 25 12:55:01 2013 -0700
drm/i915: factor out GMCH panel fitting code and use for eDP v3
broke that by reordering the computation of the gmch pfit state with
the block of code that prepared the adjusted mode for it and told the
modeset core not to overwrite the adjusted mode with default settings.
We might want to switch around the core code to just fill in defaults,
but this code predates the pipe_config modeset rework. And in the old
crtc helpers we did not have a suitable spot to do this.
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Hans de Bruin <jmdebruin@xmsnet.nl>
Reported-and-tested-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Toghether with the hw state readout this should catch cases where we
don't properly updated the pll state (either in sw or hw). At least
for the shared dpll code the equivalent tricke helped a lot in
catching bugs.
Also rename the function prefix, it's not a generic piece of
infrastructure.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec for the "DPLL HDMI multiplier" field says:
"Restriction : The DPLL must be enabled and stable before setting these bits.
These bits must be programmed after DPLL_SEL is programmed."
There is apparently no restriction on programming the DPLL_SEL
register wrt the DPLL. So let's just move that up before we enable the
pch dpll.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to call the ->pre_pll_enable hook twice if we don't enable the
dpll too early. This should make Jani a bit less grumpy.
v2: Rebase on top of the newly-colored BUG_ONs.
v3: Reinstate the lost write of the DPLL_MD register, spotted by Imre.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move error state generation and stringification to it's
own compilation unit. Sysfs also uses this so it can't be
under CONFIG_DEBUG_FS
This fixes a regression introduced in
commit ef86ddced7
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Thu Jun 6 17:38:54 2013 +0300
drm/i915: add error_state sysfs entry
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66814
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If intel_sdvo_get_value() fails here, val is unitialized and the cross
check will compare the pipe config multiplier with a bogus value.
Instead, only set encoder_pixel_multiplier when the sdvo command has
been successful. The cross check will compare the pipe config value with
0 otherwise.
v2: Do the cross check with the initial value of encoder_pixel_multiplier (0)
if the sdvo command fails (and thus keep the warning) (Daniel Vetter)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Came accross two open coding of for_each_pipe(), might as well use the
macro.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's in the PFIT_CONTROL register, but very much associated with the
lvds encoder. So move the readout for it (in the case of an otherwise
disabled pfit) from the pipe to the lvds encoder's get_config
function.
Otherwise we get a pipe state mismatch if we use pipe B for a non-lvds
output and we've left the dither bit enabled behind us. This can
happen if the BIOS has set the bit (some seem to unconditionally do
that, even in the complete absence of an lvds port), but not enabled
pipe B at boot-up. Then we won't clear the pfit control register since
we can only touch that if the pfit is associated with our pipe in the
crtc configuration - we could trample over the pfit state of the other
pipe otherwise since it's shared. Once pipe B is enabled we notice
that the 6to8 dither bit is set and complain about the mismatch.
Note that testing indicates that we don't actually need to set this
bit when the pfit is disabled, dithering on 18bpp panels seems to work
regardless. But ripping that code out is not something for a bugfix
meant for -rc kernels.
v2: While at it clarify the logic in i9xx_get_pfit_config, spurred by
comments from Chris on irc.
v3: Use Chris suggestion to make the control flow in
i9xx_get_pfit_config easier to understand.
v4: Kill the extra line, spotted by Chris.
Reported-by: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Knut Petersen <Knut_Petersen@t-online.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
References: http://lists.freedesktop.org/archives/intel-gfx/2013-July/030092.html
Tested-by: Knut Petersen <Knut_Petersen@t-online.de>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The code to handle it is broken - there's simply no code to clear CS
parser errors on gen5+. And behold, for all the other rings we also
don't enable it!
Leave the handling code itself in place just to be consistent with the
existing mess though. And in case someone feels like fixing it all up.
This has been errornously enabled in
commit 12638c57f3
Author: Ben Widawsky <ben@bwidawsk.net>
Date: Tue May 28 19:22:31 2013 -0700
drm/i915: Enable vebox interrupts
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the simplified locking there's no reason any more to keep the
refcounts seperate.
v2: Readd the lost comment that ring->irq_refcount is protected by
dev_priv->irq_lock.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the rps interrupt locking isn't clearly separated (at elast
conceptually) from all the other interrupt locking having a different
lock stopped making sense: It protects much more than just the rps
workqueue it started out with. But with the addition of VECS the
separation started to blurr and resulted in some more complex locking
for the ring interrupt refcount.
With this we can (again) unifiy the ringbuffer irq refcounts without
causing a massive confusion, but that's for the next patch.
v2: Explain better why the rps.lock once made sense and why no longer,
requested by Ben.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And kill the comment about it. Queueing work is a barrier type event,
no amount of locking will help in ordering things (as long as we queue
the work after having updated all relevant data structures). Also, the
queue_work works itself as a sufficient memory barrier.
Again on the surface this is just a tiny micro-optimization to reduce
the hold-time of dev_priv->irq_lock. But the better reason is that it
reduces superficial locking and so makes it clearer what we actually
need for correctness.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The if (pm_iir & ~GEN6_PM_RPS_EVENTS) check was redunandant. Otoh
adding a check for rps events allows us to avoid the spinlock grabbing
for VECS interrupts.
v2: Drop misplaced hunk which now moved to the right patch.
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we only have one interrupt handler and interrupt handlers are
non-reentrant.
To drive the point really home give them all an _irq_handler suffix.
This is a tiny micro-optimization but even more important it makes it
clearer what locking we actually need. And in case someone screws this
up: lockdep will catch hardirq vs. other context deadlocks.
v2: Fix up compile fail.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's racy: There's no guarantee that we won't walk this code (due to a
pch fifo underrun interrupt) while someone is changing the pointers
around.
The only reason we do this is to use the righ crtc for the pch fifo
underrun accounting. But we never expose this to userspace, so
essentially no one really cares if we use the "wrong" crtc.
So let's just rip it out.
With this patch fifo underrun code will always use crtc A for tracking
underruns on the (only) pch transcoder on LPT.
v2: Add a big comment explaining what's going on. Requested by Paulo.
v3: Fixup spelling in comment as spotted by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same treatment as for SERR_INT: If we clear only the bit for the pipe
we're enabling (but unconditionally) then we can always check for
possible underruns after having disabled the interrupt. That way pipe
underruns won't be lost, but at worst only get reported in a delayed
fashion.
v2: The same logic bug as in the SERR handling change also existed
here. The same bugfix of only reporting missed underruns when the
error interrupt was masked applies, too.
v3: Do the same fixes as for the SERR handling that Paulo suggested in
his review:
- s/%i/%c/ fix in the debug output
- move the DE_ERR_INT_IVB read into the respective if block
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fix up the checkpatch bikeshed Paulo noticed.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current code won't report any fifo underruns on cpt if just one
pipe has fifo underrun reporting disabled. We can't enable the
interrupts, but we can still check the per-transcoder bits and so
report the underrun delayed if:
- We always clear the transcoder's bit (and none of the other bits)
when enabling.
- We check the transcoder's bit after disabling (to avoid racing with
the interrupt handler).
v2: I've forgotten to actually remove the old SERR_INT clearing.
v3: Use transcoder_name as suggested by Paulo Zanoni. Paulo also
noticed a logic bug: When an underrun interrupt fires we report it
both in the interrupt handler and when checking for underruns when
disabling it in cpt_set_fifo_underrun_reporting. But that second check
is only required if the interrupt is disabled and we're switching of
underrun reporting (e.g. because we're disabling the crtc). Hence
check for that condition.
At first I wanted to rework the code to pass that bit of information
from the uppper functions down to cpt_set_fifo_underrun_reporting. But
that turned out too messy. Hence the quick&dirty check whether the
south error interrupt source is masked off or not.
v4: Streamline the control flow a bit.
v5: s/pipe/pch transcoder/ in the dmesg output, suggested by Paulo.
v6: Review from Paulo:
- Reorder the was_enabled assignment to only read the register when we
need it. Also add a comment that we need to do that before updating
the register.
- s/%i/%c/ fix for the debug output.
- Fix the checkpath complaint in the SERR_INT_TRANS_FIFO_UNDERRUN
#define.
v7: Hopefully put that elusive SERR hunk back into this patch, spotted
by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way all changes to SDEIMR all go through the same function, with
the exception of the (single-threaded) setup/teardown code.
For paranoia again add an assert_spin_locked.
v2: For even more paranoia also sprinkle a spinlock assert over
cpt_can_enable_serr_int since we need to have that one there, too.
v3: Fix the logic of interrupt enabling, add enable/disable macros for
the simple cases in the fifo code and add a comment. All requested by
Paulo.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 25ff119 and the follow on for Valleyview commit 2dc8aae.
commit 25ff1195f8
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Apr 4 21:31:03 2013 +0100
drm/i915: Workaround incoherence between fences and LLC across multiple CPUs
commit 2dc8aae06d
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed May 22 17:08:06 2013 +0100
drm/i915: Workaround incoherence with fence updates on Valleyview
Jon Bloomfield came up with a plausible explanation and cheap fix
(drm/i915: Fix incoherence with fence updates on Sandybridge+) for the
race condition, so lets run with it.
This is a candidate for stable as the old workaround incurs a
significant cost (calling wbinvd on all CPUs before performing the
register write) for some workloads as noted by Carsten Emde.
Link: http://lists.freedesktop.org/archives/intel-gfx/2013-June/028819.html
References: https://www.osadl.org/?id=1543#c7602
References: https://bugs.freedesktop.org/show_bug.cgi?id=63825
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This hopefully fixes the root cause behind the workaround added in
commit 25ff1195f8
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Thu Apr 4 21:31:03 2013 +0100
drm/i915: Workaround incoherence between fences and LLC across multiple CPUs
Thanks to further investigation by Jon Bloomfield, he realised that
the 64-bit register might be broken up by the hardware into two 32-bit
writes (a problem we have encountered elsewhere). This non-atomicity
would then cause an issue where a second thread would see an
intermediate register state (new high dword, old low dword), and this
register would randomly be used in preference to its own thread register.
This would cause the second thread to read from and write into a fairly
random tiled location. Breaking the operation into 3 explicit 32-bit
updates (first disable the fence, poke the upper bits, then poke the lower
bits and enable) ensures that, given proper serialisation between the
32-bit register write and the memory transfer, that the fence value is
always consistent.
Armed with this knowledge, we can explain how the previous workaround
work. The key to the corruption is that a second thread sees an
erroneous fence register that conflicts and overrides its own. By
serialising the fence update across all CPUs, we have a small window
where no GTT access is occurring and so hide the potential corruption.
This also leads to the conclusion that the earlier workaround was
incomplete.
v2: Be overly paranoid about the order in which fence updates become
visible to the GPU to make really sure that we turn the fence off before
doing the update, and then only switch the fence on afterwards.
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Carsten Emde <C.Emde@osadl.org>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In kernel modeset driver mode we're in full control of the chip,
always. So there's no need at all to set mm.suspended in
i915_gem_idle. Hence move that out into the leavevt ioctl. Since
i915_gem_idle doesn't suspend gem any more we can also drop the
re-enabling for KMS in the thaw function.
Also clean up the handling of mm.suspend at driver load by coalescing
all the assignments.
Stumbled over while reading through our resume code for unrelated
reasons.
v2: Shovel mm.suspended into the (newly created) ums dungeon as
suggested by Chris Wilson. The plan is that once we've completely
stopped relying on the register save/restore code we could shovel even
that in there.
v3: Improve the locking for the entervt/leavevt ioctls a bit by moving
the dev->struct_mutex locking outside of i915_gem_idle. Also don't
clear dev_priv->ums.mm_suspended for the kms case, we allocate it with
kzalloc. Both suggested by Chris Wilson.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel noticed a problem where is we wrote to an object with ring A in
the middle of a very long running batch, then executed a quick batch on
ring B before a batch that reads from the same object, its obj->ring would
now point to ring B, but its last_write_seqno would be still relative to
ring A. This would allow for the user to read from the object before the
GPU had completed the write, as set_domain would only check that ring B
had passed the last_write_seqno.
To fix this simply (and inelegantly), we bump the last_write_seqno when
switching rings so that the last_write_seqno is always relative to the
current obj->ring.
This fixes igt/tests/gem_write_read_ring_switch.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
[danvet: Add note about the newly created igt which exercises this
bug.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch partially reverts commit 36ec8f8774 for
IvyBridge CPUs.
The original commit results in repeated 'Timed out waiting for forcewake old
ack to clear' messages on a Supermicro C7H61 board (BIOS version 2.00 and 2.00b)
with i7-3770K CPU. It ultimately results in a hangup if the system is highly
loaded. Reverting the commit for IvyBridge CPUs fixes the issue.
Issue a warning if the CPU is IvyBridge and mt forcewake is disabled, since
this condition can result in secondary issues.
v2: Only revert patch for Ivybridge CPUs
Issue info message if mt forcewake is disabled on Ivybridge
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60541
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66139
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
I just got confirmation that we're using some old values for the PLL
LPF coefficients for DP RBR/HDMI/DAC on VLV. The
VLV2A0_DP_eDP_HDMI_DPIO_driver_vbios_notes_9 document lists both values
by mistake, and apparently we had picked the wrong one. Change the
coefficients to the recommended values.
Changing the value doesn't appear to destabilize the VGA output picture
even with my sensitive HP ZR24w display. Also HDMI output to my TV still
works fine.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Bail out if we hit the WARN_ON to avoid fallout later on. Spotted
by Chris Wilson.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Originally I've thought that this fixes up the reset issues on my
gm45, but that was just a red herring due to b0rked testing.
Still I much prefer writing the right values (all other fields are
reserved) instead of potentially dragging gunk around. Hence also
clear the register to 0 after a reset.
Note that Cspec is a bit confused and doesn't explicitly say that all
the other bits in this register are "reserved, mbz" like usually.
Instead they're marked as "r/o, default value = 0" which semantically
amounts to the same thing.
v2: Stop claiming this fixes anything and return 0 if successful
instead of stack garbage.
v3: Pimp the commit message to explain exactly why I think the docs
allow us to ditch the rmw cycle, spurred by a discussion with Chris.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DP 1.2 compatible displays may report a 5.4Gbps maximum bandwidth which
the driver will treat as an invalid value and use 1.62Gbps instead. Fix
this by capping to 2.7Gbps for sinks reporting a 5.4Gbps max bw.
Also add a warning for reserved values.
v2:
- allow only bw values explicitly listed in the DP standard (Daniel,
Chris)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not a good idea to also run the pipe_control cleanup.
This regression has been introduced whith the original cs tlb w/a in
commit b45305fce5
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Dec 17 16:21:27 2012 +0100
drm/i915: Implement workaround for broken CS tlb on i830/845
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64610
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
obj->mm_list link to dev_priv->mm.inactive_list/active_list
obj->global_list link to dev_priv->mm.unbound_list/bound_list
This regression has been introduced in
commit 93927ca52a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jan 10 18:03:00 2013 +0100
drm/i915: Revert shrinker changes from "Track unbound pages"
Cc: stable@vger.kernel.org
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
[danvet: Add regression notice.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the audio driver is using our power well API, everything
should be working correctly, so let's give it a try.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Sanity check that the memory region found through the Graphics Base
of Stolen Memory is reserved and hidden from the rest of the system
through the use of the resource API.
v2: "Graphics Stolen Memory" is such a more bodacious name than the lame
"i915 stolen", and convert to using devres for automagical cleanup of
the resource. (danvet)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
[danvet: Dump proper hexcodes.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At least for the common cases where we only need special file
operations. The forcewake file is still rather more special.
v2: Fix up the debugfs unregister code.
v3: Actually squash in the right fixup.
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Section 1.5.4, "DPLL A Control Register" from Bspec about bit 23
"FPA0/A1 P2 Clock Divide":
0 = Divide by 2
1 = Divide by 4. This bit must be set in DVO non-gang mode
So copy the current limits (which should be good for i8xx) and create
a new set for dvo encoders.
Reviewed-by: Chris Wilson <chris@chris-wilson.oc.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've missed that intel_dvo_mode_set changes the dpll configuration.
Hence when I've reworked the sequence to only enable the dpll in the
crtc_enable callback in
commit 66e3d5c099
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jun 16 21:24:16 2013 +0200
drm/i915: move i9xx dpll enabling into crtc enable function
that special DVO bit was lost. Some BSpec reading confirms that it's
only needed for DVO encoders. Section 1.5.4, "DPLL A Control Register"
for bit 30:
"2X Clock Enable. When driving In non-gang DVO modes such as a
connected flat panel or TV, a 2X" version of the clock is needed. When
not using the 2X output it should be disabled. This bit cannot be set
when driving the integrated LVDS port on devices such as Montara-GM."
Fix this regression up.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66516
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Partially-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Embedding the node in the obj is more natural in the transition to VMAs
which will also have embedded nodes. This change also helps transition
away from put_block to remove node.
Though it's quite an uncommon occurrence, it's somewhat convenient to not
fail at bind time because we cannot allocate the node. Though in
practice there are other allocations (like the request structure) which
would probably make this point not terribly useful.
Quoting Daniel:
Note that the only difference between put_block and remove_node is
that the former fills up the preallocation cache. Which we don't need
anyway and hence is just wasted space.
v2: Clean up the stolen preallocation code.
Rebased on the reserve_node patches
renames ggtt_ stuff to gtt_ stuff
WARN_ON if the object is already bound (which doesn't mean it's in the
bound list, tricky)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the getters in place from the previous patch this members serves no
purpose other than saving one spare pointer chase, which will be killed
in the next patch anyway.
Moving to VMAs, this members adds unnecessary confusion since an object
may exist at different offsets in different VMs.
v2: Properly preserve the stolen offset. This code is a bit hacky but it
all goes away when we embed the drm_mm_node and removes the need for the
incorrect patch I submitted previously: "Use gtt_space->start for stolen
reservation"
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Soon we want to gut a lot of our existing assumptions how many address
spaces an object can live in, and in doing so, embed the drm_mm_node in
the object (and later the VMA).
It's possible in the future we'll want to add more getter/setter
methods, but for now this is enough to enable the VMAs.
v2: Reworked commit message (Ben)
Added comments to the main functions (Ben)
sed -i "s/i915_gem_obj_set_color/i915_gem_obj_ggtt_set_color/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_bound/i915_gem_obj_ggtt_bound/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_size/i915_gem_obj_ggtt_size/" drivers/gpu/drm/i915/*.[ch]
sed -i "s/i915_gem_obj_offset/i915_gem_obj_ggtt_offset/" drivers/gpu/drm/i915/*.[ch]
(Daniel)
v3: Rebased on new reserve_node patch
Changed DRM_DEBUG_KMS to actually work (will need fixing later)
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the previous patch we no longer actually create a node, we simply
find the correct hole and occupy it. This very well could have been
squashed with the last patch, but since I already had David's review, I
figured it's easiest to keep it distinct.
Also update the users in i915. Conveniently this is the only user of the
interface.
CC: David Airlie <airlied@linux.ie>
CC: <dri-devel@lists.freedesktop.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For an upcoming patch where we introduce the i915 VMA, it's ideal to
have the drm_mm_node as part of the VMA struct (ie. it's pre-allocated).
Part of the conversion to VMAs is to kill off obj->gtt_space. Doing this
will break a bunch of code, but amongst them are 2 callers of
drm_mm_create_block(), both related to stolen memory.
It also allows us to embed the drm_mm_node into the object currently
which provides a nice transition over to the new code.
v2: Reordered to do before ripping out obj->gtt_offset.
Some minor cleanups made available because of reordering.
v3: s/continue/break on failed stolen node allocation (David)
Set obj->gtt_space on failed node allocation (David)
Only unref stolen (fix double free) on failed create_stolen (David)
Free node, and NULL it in failed create_stolen (David)
Add back accidentally removed newline (David)
CC: <dri-devel@lists.freedesktop.org>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just to keep the paranoia equal also sprinkle locking asserts over the
pipestat interrupt enable/disable functions.
Again this results in false positives in the interrupt setup. Add
bogo-locking for these and a big comment explaining why it's there and
that it's indeed unnecessary.
v2: Fix up the spelling fail Paulo spotted in comments.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A magic -1 is a obscure, especially since it's actually passed as an
unsigned, so depends upon the magic sign extension rules in C. This has
been added in
commit 3727d55e4d
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed May 8 10:45:14 2013 -0700
drm/i915: allow stolen, pre-allocated objects to avoid GTT allocation v2
Use a proper #define instead. Spotted while reviewing Ben's
drm_mm_create_block changes.
v2: Cast the constant to u32 since otherwise we again have a type
mismatch. Suggested by Chris Wilson.
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only do this on IBX where there's a fixed pch dpll to pipe
assignment. Being explicit about it can't really hurt and makes
sparse happy.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes sparse happy and also makes it a bit more obvious where we
pull off this trick - after all we're only allowed to do it eithe as a
default or on platforms where there is no disdinction between the pipe
and the cpu transcoder.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fixes gpu reset on my gm45 - without this patch the bsd thing is
forever stuck since the seqno updates never reach the status page.
Tbh I have no idea how this ever worked without rewriting the hws
registers after a gpu reset.
To satisfy my OCD also give the functions a bit more consistent names:
- Use status_page everywhere, also for the physical addressed one.
- Use init for the allocation part and setup for the register setup
part consistently.
Long term I'd really like to share the hw init parts completely
between gpu reset, resume and driver load, i.e. to call
i915_gem_init_hw instead of the individual pieces we might need.
v2: Add the missing paragraph to the commit message about what bug
exactly this patch here fixes.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65495
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: lu hua <huax.lu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This replaceable mainboard only has a VGA-out, yet it claims to also have
a connected LVDS header.
Addresses https://bugs.freedesktop.org/show_bug.cgi?id=65256
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reported-by: Cornel Panceac <cpanceac@gmail.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <annndddrr@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This replaceable mainboard only has a VGA-out, yet it claims to also have
a connected LVDS header.
Addresses https://bugs.freedesktop.org/show_bug.cgi?id=63860
[jani.nikula@intel.com: use DMI_EXACT_MATCH for board name.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reported-by: <annndddrr@gmail.com>
Cc: Cornel Panceac <cpanceac@gmail.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use wait_for() instead of the open coded loop to avoid spreading the
same old timeout related bugs.
This changes the loop to use msleep(1) instead of udelay(10) when the
Punit had not yet completed the frequency change. In practice that
doesn't seem to hurt performance as the Punit appears to be ready pretty
much always.
Also give the status bit a name, instead of using the magic number 1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Every other place properly checks whether we've managed to set
up the stolen allocator at boot-up properly, with the exception
of the cleanup code. Which results in an ugly
*ERROR* Memory manager not clean. Delaying takedown
at module unload time since the drm_mm isn't initialized at all.
v2: While at it check whether the stolen drm_mm is initialized instead
of the more obscure stolen_base == 0 check.
v3: Fix up the logic. Also we need to keep the stolen_base check in
i915_gem_object_create_stolen_for_preallocated since that can be
called before stolen memory is fully set up. Spotted by Chris Wilson.
v4: Readd the conversion in i915_gem_object_create_stolen_for_preallocated,
the check is for the dev_priv->mm.gtt_space drm_mm, the stolen
allocatot must already be initialized when calling that function (if
we indeed have stolen memory).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65953
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: lu hua <huax.lu@intel.com> (v3)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This should help on HSW, where we don't currently have a get_clock call.
Reported-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Print out the flag that failed and fix up a mismatched paren.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As getting error state doesn't anymore require big kmallocs,
make error state accessible also from sysfs.
v2: - error state clearing (Chris Wilson)
- user hint, proper access mode bits and name (Daniel Vetter)
v3: release resources in proper order (Chris Wilson)
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Apply Chris' s/error_state/error/ bikeshed on the sysfs
name. Also update the dmesg message, spotted by Chris.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make function for struct i915_error_state_buf initialization
and export it, for sysfs and debugfs.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for sysfs error state access,
export ref error state ref counting interface.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for accessing error state from sysfs, export
error state to string conversion function. Also tuck buffer
error handling inside the function.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the crtc is active, we can simply flip a new fb onto it, provided the
other mode setting reqs are met. Otherwise, we'll need to do a full
mode set to re-enable the crtc.
v2: check for crtc active and set mode_changed accordingly
v3: add module parameter, i915.fastboot, to control no fb -> fb flip behavior
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Need better pfit tracking to do this right.
v2: use fastboot param around this hack
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already fetch and track other state into the main CRTC and encoder
structs, and for fastboot we need to do the same with the mode and clock
data we read out.
v2: fix debug print
v3: use fastboot param around state copy
v4: set clock and flags for crtc here instead of in setup_hw_state
v5: rename function to intel_crtc_mode_from_pipe_config for consistency (Chris)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this for comparing modes between configuration changes.
The tricky part is to allow us to reuse the new get_clock stuff to
recover the lvds clock on gen2/3 when neither the vbt has an lvds mode
nor the panel a (useful) EDID.
v2: try harder to calulate non-simple pixel clocks (Daniel)
call get_clock after getting the encoder config, needed for pixel multiply
(Jesse)
v3: drop get_clock now that the pixel_multiply has been moved into
get_pipe_config
v4: re-add get_clock; we need to get the pixel multiplier in the
encoder, so need to calculate the clock value after the encoder's
get_config is called
v5: drop hsw clock_get, still needs to be written
v6: add fuzzy clock check (Daniel)
v7: wrap fuzzy clock check under !IS_HASWELL
use port_clock field rather than a new CPU eDP clock field in crtc_config
v8: remove stale pixel_multiplier sets (Daniel)
multiply by pixel_multiplier in 9xx clock get too (Daniel)
v9: make sure we set pixel_multiplier before calling clock_get from mode_get
for LVDS (Daniel)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add some explanation to the commit message about why we have
to jump through a few hoops. Also remove the rebase-fail hunk from
intel_sdvo.c]
[danvet: Squash in the fixup from Jesse to also call ->get_clock in
the modeset state checker.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Handling all the state properly for fastboot is still not yet done by
far, but we need some way to be able to test what we currently have.
So hide the not-yet-quite-complete stuff behind a module option.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Add a real commit message.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we painstakingly track the shared pch dplls we can finally
implement pixel mutliplier readout support for pch ports, too.
v2: Undo the temporary hack to disable the sdvo pixel multiplier
cross-checking.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
for file in `ls drivers/gpu/drm/i915/*.c` ; do
sed -i "s/mm.gtt_mtrr/gtt.mtrr/" $file;
done
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Resolve conflict with Damien's FBC_CHIP_DEFAULT no fbc
reason.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The original pte_encode function needed the dev argument so we could do
platform specific handling via IS_GENX, etc. With the merging of a pte
encoding function there should never been a need to quirk away gen
specific details.
The patch doesn't do much but makes the upcoming reworks in gtt/ppgtt/mm
slightly (albeit, ever so) easier.
Reviewed-by: Kenneth Graunke <kenneth@whitecape.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There isn't any special reason to do this other than it makes it obvious
that the two members are connected.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A previous patch had set up the ppgtt and ggtt to use the same scratch
page, but still kept around both pointers. Kill it, it's not needed and
gets in our way for upcoming cleanups.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Nothing outside of i915_gem_gtt.c and more specifically, the relevant
gen specific init function should need to know about number of PDEs, or
PTEs per PD. Exposing this will only lead to circumventing using the
upcoming VM abstraction.
To accomplish this, move the defines into the .c file, rename the PDE
define to be GEN6, and make the PTE count less of a magic number.
The remaining code in the global gtt setup is a bit messy, but an
upcoming patch will clean that one up.
v2: Don't hardcode number of PDEs (Daniel + Jesse)
Reworded commit message to reflect change.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not only was there an extra, but since we now kzalloc the error state,
we don't need either.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DPLL lock bit, and the DPIO phy status bits are read-only and
controlled by the hardware, so they will never be set by the driver.
Mask them out when reading the hw state, so that the state
comparison won't fail.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuosugeek.org>
[danvet: Jesse asked for a code comment and I wholeheartly agree, so
added one.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i9xx doesn't use pre_enable at all, so we can fold this in now.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have the proper pipe config to track this, we don't need
to write any registers any more.
Note that for platforms without DPLL_MD (pre-gen4) which store the
pixel mutliplier in the DPLL register I've decided to keep the
seemingly "redundant" write: The comment right below saying "do this
trice for luck" doesn't instill confidence ...
v2: Drop a few now unnecessary local variables and switch the enable
function to take a struct intel_crtc * to simply arguments.
v3: Rebase on top of the newly-colored BUG_ON.
v4: Amend commit message to alliviate Imre's comment about the
redudant DPLL write for the pixel mutliplier.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In addition to existing stuff we also need to track DPLL_MD on gen4
and vlv. This is prep work so that we can move the dpll enable
sequence out from the ->mode_set callback into the crtc enabling
functions.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ->pre_enable hook is only used for the cpu edp port on ilk-ivb, so
we can safely move it up across the fdi pll enabling.
Unfortunately we can't (yet) merge in the pre_pll enable hook despite
that only lvds uses it on ilk-ivb: Since the same lvds hook is also
need on i9xx platforms we need to fix up the pll enabling sequence
there, too.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Lots of bangin my head against the wall^UExperiments have shown that
we really need to enable the lvds port before we enable plls. Strangely
that seems to include the fdi rx pll on the pch.
Note that the pch pll assert can fire since the lvds port has it's own
special clock source settings in the DPLL register, which means it
will never have a shared dpll (since there's only one LVDS port).
Anyway, encode this new evidence with a few nice WARNs.
v2: Incorporate review comments from Imre.
- Explain why lvds can't have a shared dpll.
- Update the WARN output.
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Mostly since I _really_ don't want to touch the vlv hell.
No code change, just duplication. Also kill a now seriously outdated
code comment - the remark about the dvo encoder is now handled with
the pipe A quirk.
v2: Update the BUG_ONs as suggested by Jani (both in vlv_ and i9xx_
functions, since the split happens here).
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just yet another prep step to be able to do all this up-front, before
we've set up any of the shared dplls in the new state. This will
eventually be useful for atomic modesetting.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's been splattered over 3 different places all doing random things.
Now we have (mostly) the same sequence as i8xx/i9xx, but all called
from the crtc_enable hook (through the pll->enable function):
- write new dividers
- enable vco and wait for stable clocks
- write again for the pixel mutliplier
I've left the seemingly random 200 usec delay in there, just in case.
Also move the encoder->pre_pll_enable hook into the crtc_enable
function, at the same spot we currently have a hack to enable the lvds
port. Since that hack is now redundant, kill it.
While doing this patch I've learned the hard way that we can only fire
up the LVDS port if both the pch dpll _and_ the fdi rc pll are not yet
enabled. Otherwise things go haywire, at least on cpt.
v2: It is paramount to write the FPx divisors before we enable the
the vco by writing to the DPLL registers, for otherwise the divisors
won't get updated. This is in line with the i8xx/i9xx dpll.
v3: To keep the nice abstraction add a ->mode_set callback to set the
divisors. Also streamline the enabling/disabling code a bit by
removing some cargo-cult duplication and clearing registers where
possible in the ->disable hook.
v4: Remove now unused local variable.
Acked-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Once we've found the the context object programmed in CCID, there's no
need to look the other objects in the list.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A genuine 'static' omission and 2 other warnings triggered by not
including the header where those functions where defined.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Caught with checkpatch.pl.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When running on my snb machine, recent kernels display successively:
[drm:intel_update_fbc], fbc set to per-chip default
[drm:intel_update_fbc], fbc disabled per module param
But no module param is set. This happens because the check for the
module parameter uses a variable that has been overridden inside the
"per-chip default" code.
Fix up the logic and add another reason for the FBC to the be disabled.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This function has no user outside of intel_pm.c.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently print a DRM_DEBUG_KMS message on the happy path and don't
print anything on the "failed to allocate" path. On some desktop
environments (e.g., Unity) I see the "scheduling delayed FBC enable"
thousands and thousands of times on my dmesg.
So kill the useless message for the happy case, saving a lot of dmesg
space, and properly signal the "kzalloc fail" case.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So it appears that I have encountered some bogosity when trying to call
i915_error_printf() with many arguments from print_error_buffers(). The
symptom is that the vsnprintf parser tries to interpret an integer arg
as a character string, the resulting OOPS indicating stack corruption.
Replacing the single call with its 13 format specifiers and arguments
with multiple calls to i915_error_printf() worked fine. This patch goes
one step further and introduced i915_error_puts() to pass the strings
simply.
It may not fix the root cause, but it does prevent my box from dying and
I think helps make print_error_buffers() more friendly.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66077
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Harmonise the completion logic between the non-blocking and normal
wait_rendering paths, and move that logic into a common function.
In the process, we note that the last_write_seqno is by definition the
earlier of the two read/write seqnos and so all successful waits will
have passed the last_write_seqno. Therefore we can unconditionally clear
the write seqno and its domains in the completion logic.
v2: Add the missing ring parameter, because sometimes it is good to have
things compile.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the introduction of the non-blocking wait, I cut'n'pasted the wait
completion code from normal locked path. Unfortunately, this neglected
that the normal path returned early if the wait returned early. The
result is that read-only waits may return whilst the GPU is still
writing to the bo.
Fixes regression from
commit 3236f57a01 [v3.7]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Aug 24 09:35:09 2012 +0100
drm/i915: Use a non-blocking wait for set-to-domain ioctl
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66163
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On DevCPT, the control register for Transcoder DP Sync Polarity is
TRANS_DP_CTL, not DP_CTL.
Without this patch, Many call trace occur on CPT machine with DP monitor.
The call trace is like: *ERROR* mismatch in adjusted_mode.flags(expected X,found X)
v2: use intel-crtc to simple patch, suggested by Daniel.
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
[danvet: Extend the encoder->get_config comment to specify that we now
also depend upon intel_encoder->base.crtc being correct. Also bikeshed
s/intel_crtc/crtc/.]
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65287
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Our interrupt handler (in hardirq context) could race with the timer
(in softirq context), hence we need to hold the spinlock around the
call to ->hdp_irq_setup in intel_hpd_irq_handler, too.
But as an optimization (and more so to clarify things) we don't need
to do the irqsave/restore dance in the hardirq context.
Note also that on ilk+ the race isn't just against the hotplug
reenable timer, but also against the fifo underrun reporting. That one
also modifies the SDEIMR register (again protected by the same
dev_priv->irq_lock).
To lock things down again sprinkle a assert_spin_locked. But exclude
the functions touching SDEIMR for now, I want to extract them all into
a new helper function (like we do already for pipestate, display
interrupts and all the various gt interrupts).
v2: Add the missing 't' Egbert spotted in a comment.
v3: Actually fix the right misspelled comment (Paulo).
Cc: Egbert Eich <eich@suse.de>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The usual pattern for our sub-function irq_handlers is that they check
for the no-irq case themselves. This results in more streamlined code
in the upper irq handlers.
v2: Rebase on top of the i965g/gm sdvo hpd fix.
Cc: Egbert Eich <eich@suse.de>
Reviewed-by: Egbert Eich <eich@suse.de>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Everywhere the same.
Note that this patch leaves unnecessary braces behind, but the next
patch will kill those all anyway (including the if itself) so I've
figured I can keep the diff a bit smaller.
v2: Rebase on top of the i965g/gm sdvo hpd fix.
Cc: Egbert Eich <eich@suse.de>
Reviewed-by: Egbert Eich <eich@suse.de>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already have a vfunc for this (and other parts of the hpd storm
handling code already use it).
v2: Rebase on top of the i965g/gm sdvo hpd fix.
Cc: Egbert Eich <eich@suse.de>
Reviewed-by: Egbert Eich <eich@suse.de>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The combination of Paulo's fifo underrun detection code and Egbert's
hpd storm handling code unfortunately made the hpd storm handling code
racy.
To avoid duplicating tricky interrupt locking code over all platforms
start with a bit of refactoring. This patch is the very first step
since in the end the irq storm handling code will handle all hotplug
logic (and so also encapsulate the locking nicely).
v2: Rebase on top of the i965g/gm sdvo hpd fix.
Cc: Egbert Eich <eich@suse.de>
Reviewed-by: Egbert Eich <eich@suse.de>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By the time we write DEIER in the postinstall hook the interrupt
handler could run any time. And it does modify DEIER to handle
interrupts.
Hence the DEIER read-modify-write cycle for enabling the PCU event
source is racy. Close this races the same way we handle vblank
interrupts: Unconditionally enable the interrupt in the IER register,
but conditionally mask it in IMR. The later poses no such race since
the interrupt handler does not touch DEIMR.
Also update the comment, the clearing has already happened
unconditionally above.
v2: Actually shove the updated comment into the right train^W commit,
as spotted by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The haswell unclaimed register handling code forgot to take the
spinlock. Since this is in the context of the non-rentrant interupt
handler and we only have one interrupt handler it is sufficient to
just grab the spinlock - we do not need to exclude any other
interrupts from running on the same cpu.
To prevent such gaffles in the future sprinkle assert_spin_locked over
these functions. Unfornately this requires us to hold the spinlock in
the ironlake postinstall hook where it is not strictly required:
Currently that is run in single-threaded context and with userspace
exlcuded from running concurrent ioctls. Add a comment explaining
this.
v2: ivb_can_enable_err_int also needs to be protected by the spinlock.
To ensure this won't happen in the future again also sprinkle a
spinlock assert in there.
v3: Kill the 2nd call to ivb_can_enable_err_int I've accidentally left
behind, spotted by Paulo.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With updates to the spec, we can actually see the context layout, and
how many dwords are allocated. That table suggests we need 70720 bytes
per HW context. Rounded up, this is 18 pages. Looking at what lives
after the current 4 pages we use, I can't see too much important (mostly
it's d3d related), but there are a couple of things which look scary. I
am hopeful this can explain some of our odd HSW failures.
v2: Make the context only 17 pages. The power context space isn't used
ever, and execlists aren't used in our driver, making the actual total
66944 bytes.
v3: Add a comment to the code. (Jesse & Paulo)
Reported-by: "Azad, Vinit" <vinit.azad@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We forgot to add VLV_DISPLAY_BASE to the VLV sprite registers, which
caused the sprites to not work at all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PIPECONF color range bit doesn't appear to be effective, on HDMI
outputs at least. The color range bit in the port register works though,
so let's use it.
I have not yet verified whether the PIPECONF bit works on DP outputs.
This reverts commit 83a2af88f8.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
LPF is short for "low pass filter".
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The current PLL settings produce a rather unstable picture when
I hook up a VLV to my HP ZR24w display via a VGA cable.
According to VLV2A0_DP_eDP_HDMI_DPIO_driver_vbios_notes_9, we should
use the the same LPF coefficients for DAC as we do for HDMI and RBR DP.
And indeed that seems to cure the shivers.
v2: Add the name of the relevant document to the commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the current GPU frquency is below RPe, and we're asked to increase
it, just go directly to RPe. This should provide better performance
faster than letting the frequency trickle up in response to the up
threshold interrupts.
For now just do it for VLV, since that matches quite closely how VLV
used to operate when the rps delayed timer kept things at RPe always.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's little point in increasing the GPU frequency from the delayed
rps work on VLV. Now when the GPU is idle, the GPU frequency actually
keeps dropping gradually until it hits the minimum, whereas previously
it just ping-ponged constantly between RPe and RPe-1.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I can't find GEN6_RP_INTERRUPT_LIMITS (0xA014) anywhere in VLV docs.
Reading it always returns zero from what I can tell, and eliminating
it doesn't seem to make any difference to the behaviour of the system.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eliminate the weird inverted logic from the rps new_delay comparison.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It seems that even though Punit reports the frequency change to have
been completed, it still reports the old frequency in the status
register for some time.
So rather than polling for Punit to complete the frequency change after
each request, poll before. This gets rid of the spurious "Punit overrode
GPU freq" messages.
This also lets us continue working while Punit is performing the actual
frequency change. As a result, openarena demo088-test1 timedemo average
fps is increased by ~5 fps, and the slowest frame duration is reduced
by ~25%.
The sysfs cur_freq file always reads the current frequency from Punit
anyway, so having rps.cur_delay be slightly off at times doesn't matter.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Always print both the MHz value and raw register value for rps stuff.
Also kill a somewhat pointless local 'rpe' variable and just use
dev_priv->rps.rpe_delay.
While at it clean up the caps in "GPU" and "Punit" debug messages.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Report back the user error of attempting to setup a CRTC with an invalid
framebuffer pitch. This is trickier than it should be as on gen4, there
is a restriction that tiled surfaces must have a stride less than 16k -
which is less than the largest supported CRTC size.
v2: Fix the limits for gen3
v3: Move check into intel_framebuffer_init() and fix VLV limits. (vsyrjala)
v4: Use idiomatic '>=' for generation checks
References: https://bugs.freedesktop.org/show_bug.cgi?id=65099
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No need to apply WaForceL3Serialization:vlv twice.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There are legit cases, e.g. when userspace asks for something
impossible. So tune it down to debug output like we do with all other
userspace-triggerable warnings.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=66111#c5
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Rebased.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bspec seems to be full of lies, at least it disagress with reality:
Two systems corrobated that SDVO hpd bits are the same as on gen3.
v2: Update comment a bit.
Cc: Arthur Ranyan <arthur.j.runyan@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-tested-by: Alex Fiestas <afiestas@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58405
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the trend and don't code conditions with platforms but with
features.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drivers/gpu/drm/i915/i915_gem.c: In function ‘i915_gem_object_bind_to_gtt’:
drivers/gpu/drm/i915/i915_gem.c:3002:3: warning: format ‘%ld’ expects
argument of type ‘long int’, but argument 5 has type ‘size_t’ [-Wformat]
v2: Use %zu instead of %d. Two char patch, and 100% wrong. (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Nothing the user (nor we) really can do about this, but upsets a nice
quiet boot.
Note that this happens mostly on SDVs where OEMs obviously haven't had
a chance yet to appropriately trim the output list.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65988
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Amend commit message a bit to clarify a question from Paulo.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Git commit 90797e6d1e
("drm/i915: create compact dma scatter lists for gem objects") makes
certain assumptions about the under laying DMA API that are not always
correct.
On a ThinkPad X230 with an Intel HD 4000 with Xen during the bootup
I see:
[drm:intel_pipe_set_base] *ERROR* pin & fence failed
[drm:intel_crtc_set_config] *ERROR* failed to set mode on [CRTC:3], err = -28
Bit of debugging traced it down to dma_map_sg failing (in
i915_gem_gtt_prepare_object) as some of the SG entries were huge (3MB).
That unfortunately are sizes that the SWIOTLB is incapable of handling -
the maximum it can handle is a an entry of 512KB of virtual contiguous
memory for its bounce buffer. (See IO_TLB_SEGSIZE).
Previous to the above mention git commit the SG entries were of 4KB, and
the code introduced by above git commit squashed the CPU contiguous PFNs
in one big virtual address provided to DMA API.
This patch is a simple semi-revert - were we emulate the old behavior
if we detect that SWIOTLB is online. If it is not online then we continue
on with the new compact scatter gather mechanism.
An alternative solution would be for the the '.get_pages' and the
i915_gem_gtt_prepare_object to retry with smaller max gap of the
amount of PFNs that can be combined together - but with this issue
discovered during rc7 that might be too risky.
Reported-and-Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Imre Deak <imre.deak@intel.com>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: David Airlie <airlied@linux.ie>
CC: <dri-devel@lists.freedesktop.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In some virtualized environments (e.g. XEN), there is irrelevant ISA bridge in
the system. To work reliably, we should scan trhough all the ISA bridge
devices and check for the first match, instead of only checking the first one.
Signed-off-by: Rui Guo <firemeteor@users.sourceforge.net>
[danvet: Fixup conflict with the num_pch_pll removal. And add
subsystem header to the commit message headline.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because it's the function that destroys the connector, not the
encoder. And we already have intel_dp_encoder_destroy.
This has annoyed me for a long time.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We've been ignoring this return value, so print a nice backtrace in
case it's not what we expected.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because calling intel_dp_encoder_destroy inside
intel_edp_init_connector is just wrong. This is the initialization
path, so we should properly unwind all the initialization through the
whole caller stack.
On the intel_dp_encoder_destroy function we do the following:
1 - Call i2c_del_adapter
2 - Call drm_encoder_cleanup
3 - If edp:
3.1 - Cancel panel_vdd_work
3.2 - Call ironlake_panel_vdd_of_sync
4 - Free the encoder
And here is how we unwind each specific step:
1 - We have intel_dp_init_connector -> intel_dp_i2c_init ->
i2c_dp_aux_add_bus -> i2c_add_adapter, so we call
i2c_del_dapter at intel_dp_init_connector
2 - Call it in the same function that called drm_encoder_init
3 - Call it in the same function that called INIT_DELAYED_WORK
4 - Free it in the same function that allocated it
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because calling intel_dp_destroy inside intel_edp_init_connector is
just wrong. This is the initialization path, so we should properly
unwind all the initialization through the whole caller stack.
On the intel_dp_destroy function we do the following:
1 - Free edid if it exists
2 - Call intel_panel_fini in case it's eDP
3 - Call drm_sysfs_connector_remove
4 - Call drm_connector_cleanup
5 - Free the connector
And here is how we unwind each specific step:
1 - No need as we still didn't assign anything
2 - No need as we still didn't call intel_panel_init
3 - Call it in the same function that called drm_sysfs_connector_add
4 - Call it in the same function that called drm_connector_init
5 - Free it in the same function that allocated it
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In case we detect a "ghost eDP", intel_edp_init_connector frees both
the connector and encoder and then returns. On Haswell, intel_ddi_init
then tries to use the freed encoder on the HDMI initialization path
since the following commit:
commit 21a8e6a485
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Apr 10 23:28:35 2013 +0200
drm/i915: don't setup hdmi for port D edp in ddi_init
So now on intel_ddi_init we check for the "ghost eDP" case and return
without trying to initialize HDMI. This way we won't try to read the
freed "intel_encoder" struct in the next "if" statement.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because intel_dp_init_connector is too big for my poor little brain.
No functional changes.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By the time we call intel_dp_destroy (which destroys the connector)
the encoder may have been destroyed already, so if we use it we may be
reading some free memory. That happens in drm_mode_config_cleanup()
and also inside intel_dp_init_connector() when we detect a ghost eDP.
I also hope this may solve some random memory bugs.
Reported by kmemcheck.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Zoltan Nyul <zoltan.nyul@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Last 3.11 feature pull. I have a few odds bits and pieces and fixes in my
queue, I'll sort them out later on to see what's for 3.11-fixes and what's
for 3.12. But nothing to hold this here up imo.
Highlights:
- more hangcheck work from Mika and Chris to prepare for arb robustness
- trickle feed fixes from Ville
- first parts of the shared pch pll rework, with some basic hw state
readout and cross-checking (this shuts up the confused pch pll refcount
WARN that Linus just recently forwarded)
- Haswell audio power well support from Wang Xingchao (alsa bits acked by
Takashi)
- some cleanups and asserts sprinkling around the plane/gamma enabling
sequence from Ville
- more gtt refactoring from Ben
- clear up the adjusted->mode vs. pixel clock vs. port clock confusion
- 30bpp support, this time for real hopefully
* tag 'drm-intel-next-2013-06-18' of git://people.freedesktop.org/~danvet/drm-intel: (97 commits)
drm/i915: remove a superflous semi-colon
drm/i915: Kill useless "Enable panel fitter" comments
drm/i915: Remove extra "ring" from error message
drm/i915: simplify the reduced clock handling for pch plls
drm/i915: stop killing pfit on i9xx
drm/i915: explicitly set up PIPECONF (and gamma table) on haswell
drm/i915: set up PIPECONF explicitly for i9xx/vlv platforms
drm/i915: set up PIPECONF explicitly on ilk-ivb
drm/i915: find guilty batch buffer on ring resets
drm/i915: store ring hangcheck action
drm/i915: add batch bo to i915_add_request()
drm/i915: change i915_add_request to macro
drm/i915: add i915_gem_context_get_hang_stats()
drm/i915: add struct i915_ctx_hang_stats
drm/i915: Try harder to disable trickle feed on VLV
drm/i915: fix up pch pll enabling for pixel multipliers
drm/i915: hw state readout and cross-checking for shared dplls
drm/i915: WARN on lack of shared dpll
drm/i915: split up intel_modeset_check_state
drm/i915: extract readout_hw_state from setup_hw_state
...
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_fb.c
drivers/gpu/drm/i915/intel_sdvo.c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQEbBAABAgAGBQJRxf9cAAoJEHm+PkMAQRiGMWkH911xM4gRmFgE7SqVW4F4AWBm
ngcqMqNy9IdqKfibORUUDvVfEa5gjD5ai2quIKpfQiaukbpQJ696H90ijuAkajLn
DQBrN243s0pzhhc/quWINnWxsFQ613JjdUMUMaD7e9A1aKjYzWrPGt/tSjrFXGCP
tArTupVzc/iOmnEQDKiROI/Nokq44QJ36aTGPM7n08xMtpKmkCXM+9/UosBteB0O
HVI33dmjwz7i55fI53XAWyuZCE+gSEnA4z8spJ9LfXso2W14V+roc+GuL6OyeeTI
pCn/+4niVPb4B0ROZlpyVmdZjbPPcMMEK5o+BSJI68SH6LHZTQh2iVuqYfpSyA==
=uUH5
-----END PGP SIGNATURE-----
Merge tag 'v3.10-rc7' into drm-next
Linux 3.10-rc7
The sdvo lvds fix in this -fixes pull
commit c3456fb3e4
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jun 10 09:47:58 2013 +0200
drm/i915: prefer VBT modes for SVDO-LVDS over EDID
has a silent functional conflict with
commit 990256aec2
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri May 31 12:17:07 2013 +0000
drm: Add probed modes in probe order
in drm-next. W simply need to add the vbt modes before edid modes, i.e. the
other way round than now.
Conflicts:
drivers/gpu/drm/drm_prime.c
drivers/gpu/drm/i915/intel_sdvo.c
Git commit 90797e6d1e
("drm/i915: create compact dma scatter lists for gem objects") makes
certain assumptions about the under laying DMA API that are not always
correct.
On a ThinkPad X230 with an Intel HD 4000 with Xen during the bootup
I see:
[drm:intel_pipe_set_base] *ERROR* pin & fence failed
[drm:intel_crtc_set_config] *ERROR* failed to set mode on [CRTC:3], err = -28
Bit of debugging traced it down to dma_map_sg failing (in
i915_gem_gtt_prepare_object) as some of the SG entries were huge (3MB).
That unfortunately are sizes that the SWIOTLB is incapable of handling -
the maximum it can handle is a an entry of 512KB of virtual contiguous
memory for its bounce buffer. (See IO_TLB_SEGSIZE).
Previous to the above mention git commit the SG entries were of 4KB, and
the code introduced by above git commit squashed the CPU contiguous PFNs
in one big virtual address provided to DMA API.
This patch is a simple semi-revert - were we emulate the old behavior
if we detect that SWIOTLB is online. If it is not online then we continue
on with the new compact scatter gather mechanism.
An alternative solution would be for the the '.get_pages' and the
i915_gem_gtt_prepare_object to retry with smaller max gap of the
amount of PFNs that can be combined together - but with this issue
discovered during rc7 that might be too risky.
Reported-and-Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Imre Deak <imre.deak@intel.com>
CC: Daniel Vetter <daniel.vetter@ffwll.ch>
CC: David Airlie <airlied@linux.ie>
CC: <dri-devel@lists.freedesktop.org>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Now that we have this all nicely abstract into separate functions with
self-documenting names this is pointless. And as Yuly Novikov spotted
in the case of ilk-ivb also wrong since we use the pfit both for lvds
and eDP
Reported-By: Yuly Novikov <ynovikov@chromium.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The ring names already have "ring" in it.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just move the lowfreq_avail logic out of the register writing as a
prep step for the next patch, which will coalesce all the pch pll
enabling into one spot.
Note that writing the reduced clock dividers to FP1 in a few more
cases (as this patch ends up doing) isn't really relevant since the
FP1 value only matters when we enable the low lock. Which despite
can only happen if we've actually enabled the reduced dotclock and
furthermore isn't even properly implemented on ilk+: Despite claims to
the contrary in the code switching between frequencies if fully
manual.
v2: Explain matters around the FP1 change to answer a question Damien
raised in his review.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Nowadays (i.e. with Valleyview) we also have edp on non-PCH_SPLIT
platforms, so just checking for LVDS is not good enough.
Secondly we have full pfit pipe config tracking, so we'll correctly
disable the pfit as part of the initial modeset.
For fastboot we need a bit of work here to correctly kill unsupported
configs (if e.g. the pfit is used on anything else than the built-in
panel). But since that's not yet supported we don't need to worry.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again we don't really support different settings, so don't let the
BIOS sneak stuff through.
Since the motivation for this patch series is to ensure we have the
correct gamma table mode selected also add the required write to the
GAMMA_MODE register to select the 8bit legacy table.
And since I find lowercase letters in #defines offensive, also
bikeshed those.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same reasons as for the previous patch, just no bug report about
anything going wrong yet: We only support exactly the mode we program,
so don't leave any stale BIOS state behind.
Again this will be fun to properly track for fastboot.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dragging random garbage along from the BIOS isn't a good idea, since
we really only support exactly what we've set up.
In the specific case for the bug reporter the BIOS used the 10bit
gamma table, but since we only support an 8bit table the dark colors
ended up all wrong and the light ones all unadjusted.
Note that this has a nice implication for fastboot, it essentially
means that we have quite a bit more state to check and compare before
we can decide whether fastboot is possible.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65593
Reported-and-Tested-by: Thomas Hebb <tommyhebb@gmail.com>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
plane->enabled is never set, so this code didn't do anything.
Also drm_fb_helper_restore_fbdev_mode() will now disable all cursors
and sprites for us, so we don't have to bother anymore.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Stéphane Marchesin found that fences for pinned objects (i.e. the
scanout) were not being restored upon resume, leading to corruption on
the display and reference counting issues. This is due to a bug in
commit 312817a39f [2.6.38]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Nov 22 11:50:11 2010 +0000
drm/i915: Only save and restore fences for UMS
that zapped the pinned fences even though they were in use.
Fortuitously, whilst we forced a VT switch during suspend and resume,
no fences were ever pinned at the time. However, we now can do
switchless S3 transitions and so the old bug finally surfaces.
Reported-by: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After hang check timer has declared gpu to be hung,
rings are reset. In ring reset, when clearing
request list, do post mortem analysis to find out
the guilty batch buffer.
Select requests for further analysis by inspecting
the completed sequence number which has been updated
into the HWS page. If request was completed, it can't
be related to the hang.
For noncompleted requests mark the batch as guilty
if the ring was not waiting and the ring head was
stuck inside the buffer object or in the flush region
right after the batch. For everything else, mark
them as innocents.
v2: Fixed a typo in commit message (Ville Syrjälä)
v3: - more descriptive function parameters (Chris Wilson)
- use masked head address when inspecting if request is in ring
- s/hangcheck.last_action/hangcheck.action
- added comment about unmasked head hitting batch_obj range
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For guilty batchbuffer analysis later on when rings are reset,
store what state the ring was on when hang was declared.
This helps to weed out the waiting rings from the active ones.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In order to track down a batch buffer and context which
caused the ring to hang, store reference to bo into the request struct.
Request can also cause gpu to hang after the batch in the flush section
in the ring. To detect this add start of the flush portion offset into the
request.
v2: Included comment about request vs batch_obj lifetimes (Chris Wilson)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only execbuffer needed all the parameters on i915_add_request().
By putting __i915_add_request behind macro, all current callsites
become cleaner. Following patch will introduce a new parameter
for __i915_add_request. With this patch, only the relevant callsite
will reflect the change making commit smaller and easier to understand.
v2: _i915_add_request as function name (Chris Wilson)
v3: change name __i915_add_request and fix ordering of params (Ben Widawsky)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To get context hang statistics for specified context,
add i915_gem_context_get_hang_stats().
For arb-robustness, every context needs to have its own
hang statistics tracking. Added function will return
the user specified context statistics or in case of
default context, statistics from drm_i915_file_private.
v2: handle default context inside get_reset_state
v3: return struct pointer instead of passing it in as param
(Chris Wilson)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
To count context losses, add struct i915_ctx_hang_stats for
both i915_hw_context and drm_i915_file_private.
drm_i915_file_private is used when there is no context.
v2: renamed and cleaned up the struct (Chris Wilson, Ian Romanick)
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The specs are a bit unclear whether the per-plane trickle feed disable
control exists on VLV. There is another trickle feed disable control
in the MI_ARB register.
After some experimentation it turns out both the DSPCNTR trickle feed
bits and the MI_ARB bit can be toggled. However the DSPCNTR bits don't
seem to have any effect.
The MI_ARB bit, on the other hand, has a noticable effect. I performed
an experiment where I reduced the FIFO size via DSPARB and observed the
effect of the MI_ARB trickle feed bit on the display.
Using a 1920x1080-60 mode, with MI_ARB=0x4 the display started to have
problems with DSPARB=0x42424242, whereas with MI_ARB=0x0 the problems
didn't start until DSPARB=0x09090909. This seems to confirm that the
MI_ARB trickle feed bit actually does work.
So replace the use of the DSPCNTR trickle feed bits with MI_ARB
on VLV.
v2: Amend commit message with results from experimentation
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have a nice comment saying that the pixel multiplier only sticks
once the vco is on and stable. The only problem is that the enable bit
wasn't set at all. This patch fixes this and so brings the ilk+ pch
pll code in line with the i8xx/i9xx pll code. Or at least improves
matters a lot.
This should fix sdvo on ilk-ivb for low-res modes.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just the plumbing, all the modeset and enable code has not yet been
switched over to use the new state. It seems to be decently broken
anyway, at least wrt to handling of the special pixel mutliplier
enabling sequence. Follow-up patches will clean up that mess.
Another missing piece is more careful handling (and fixup) of the fp1
alternate divisor state. The BIOS most likely doesn't bother to
program that one to what we expect. So we need to be more careful with
comparing that state, both for cross checking but also when checking
for dpll sharing when acquiring shared dpll. Otherwise fastboot will
deny a few shared dpll configurations which would otherwise work.
v2: We need to memcpy the pipe config dpll hw state into the pll, for
otherwise the cross-check code will get angry.
v3: Don't forget to read the pch pll state in the crtc get_pipe_config
function for ibx/ilk platforms.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we have proper hw state reconstruction we should never have a
case where we don't have the software dpll state properly set up. So
add WARNs to the respective !pll cases in enable/disabel_shared_dpll.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simply grew too large and needed to be split up into parts.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simply grew too big. This also makes the fixup and restore logic in
setup_hw_state stand out a bit more clearly.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently still with an empty register state, this will follow in a
next step. This one here just creates the new vfunc and uses it for
cross-checking, initial state takeover and the dpll assert function.
And add a FIXME for the ddi pll readout code, which still needs to be
converted over.
v2:
- Add some hw state readout debug output.
- Also cross check the enabled crtc counting.
Note that I've botched up the patch ordering, and before this patch
we've read out the pll selection correctly, but did not reconstruct
the refcounts properly. See the bug link.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65673
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So don't try to store it in the DPLL_FP register.
Otherwise it looks like the limits for pineview are correct: It has
it's own clock computation code, which doesn't use an offset for n
divisors, and the register value based m limits look sane enough.
v2: Rebase on top of the pineview clock refactor and fixup up the
commit message: It's m1 pnv doens't care about, not m2!
Quoting Damien's review:
- "n can vary between 2 and 6, but we declare the 3-6 as limits.
- "p1 seems to be able to go up to 9
- "the m upper limit seems a bit big, but the docs are a bit shy on
that values for pnv.
"Otherwise, the change itself seems good:"
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We don't (yet) have proper pixel multiplier readout support on pch
split platforms, so the cross check will naturally fail.
v2: Fix spelling in the comment, spotted by Ville.
v3: Since the ordering constraint is pretty tricky between the crtc
get_pipe_config callback and the encoder->get_config callback add a
few comments about it. Prompted by a discussion with Chris Wilson on
irc about why this does work anywhere else than on i915g/gm.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Stéphane Marchesin found a bug where the fences were not being restored,
and in particular the fence pin_count was incorrect. Had we had a
warning in place, this bug would have come to light much earlier. Better
late than never?
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Stéphane Marchesin <marcheu@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is of no value to the developer reading the report, let alone the
bamboozled user.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we detect a ring is in a valid wait for another, just let it be.
Eventually it will either begin to progress again, or the entire system
will come grinding to a halt and then hangcheck will fire as soon as the
deadlock is detected.
This error was foretold by Ben in
commit 05407ff889
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Thu May 30 09:04:29 2013 +0300
drm/i915: detect hang using per ring hangcheck_score
"If ring B is waiting on ring A via semaphore, and ring A is making
progress, albeit slowly - the hangcheck will fire. The check will
determine that A is moving, however ring B will appear hung because
the ACTHD doesn't move. I honestly can't say if that's actually a
realistic problem to hit it probably implies the timeout value is too
low."
v2: Make sure we don't even incur the KICK cost whilst waiting.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65394
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After kicking a ring, it should be free to make progress again and so
should not be accused of being stuck until hangcheck fires once more. In
order to catch a denial-of-service within a batch or across multiple
batches, we still do increment the hangcheck score - just not as
severely so that it takes multiple kicks to fail.
This should address part of Ben's justified criticism of
commit 05407ff889
Author: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Date: Thu May 30 09:04:29 2013 +0300
drm/i915: detect hang using per ring hangcheck_score
"There's also another corner case on the kick. If the seqno = 2
(though not stuck), and on the 3rd hangcheck, the ring is stuck, and
we try to kick it... we don't actually try to find out if the kick
helped."
v2: Make sure we catch DoS attempts with batches full of invalid WAITs.
v3: Preserve the ability to detect loops by always charging the ring
if it is busy on the same request.
v4: Make sure we queue another check if on a new batch
References: https://bugs.freedesktop.org/show_bug.cgi?id=65394
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we reset and restart a ring, we also want to clear any existing
hangcheck.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Daniel writes:
Another round of drm-intel-next for 3.11. Highlights:
- Haswell IPS support (Paulo Zanoni)
- VECS support on Haswell (Ben Widawsky, Xiang Haihao, ...)
- Haswell watermark fixes (Paulo Zanoni)
- "Make the gun bigger again" multithread fence fix from Chris.
- i915_error_state finnally no longer fails with -ENOMEM! Big thanks to
Mika for tackling this.
- vlv sideband locking fixes from Jani
- Hangcheck prep work for arb_robustness support (Mika&Chris)
- edp vs cpu port confusion clean-up from Imre
- pile of smaller fixes and cleanups all over.
* tag 'drm-intel-next-2013-06-01' of git://people.freedesktop.org/~danvet/drm-intel: (70 commits)
drm/i915: add i915_ips_status debugfs entry
drm/i915: add enable_ips module option
drm/i915: implement IPS feature
drm/i915: fix up the edp power well check
drm/i915: add I915_PARAM_HAS_VEBOX to i915_getparam
drm/i915: add I915_EXEC_VEBOX to i915_gem_do_execbuffer()
drm/i915: add VEBOX into debugfs
drm/i915: Enable vebox interrupts
drm/i915: vebox interrupt get/put
drm/i915: consolidate interrupt naming scheme
drm/i915: Convert irq_refounct to struct
drm/i915: make PM interrupt writes non-destructive
drm/i915: Add PM regs to pre/post install
drm/i915: Create an ivybridge_irq_preinstall
drm/i915: Create a more generic pm handler for hsw+
drm/i915: add support for 5/6 data buffer partitioning on Haswell
drm/i915: properly set HSW WM_LP watermarks
drm/i915: properly set HSW WM_PIPE registers
drm/i915: fix pch_nop support
drm/i915: Vebox ringbuffer init
...
Use drm_get_format_name to print more readable pixel format names
in debug output.
Also unify the debug messages to say "unsupported pixel format",
which better describes what is going on.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In case of intel_sdvo_get_active_outputs() failing, we end up reading a
value from the stack.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The hw state readout code for the pipe config will now check
this for us, so rip out this hand-rolled complexity.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Looks at first like a bit of overkill, but
- Haswell actually wants different enable/disable functions for
different plls.
- And once we have full dpll hw state tracking we can move the full
register setup into the ->enable hook.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Using ids in register macros is much more common in our driver. Also
this way we can reduce the platform specific stuff a bit.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
An id to match the idx (useful for register access macros) and a name
fore neater debug output.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the future this won't be just for pch plls, so move it into the
shared dpll init code.
v2: Bikeshed the uncessary {} away while applying to appease
checkpatch.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Well, the first step of a long road at least, it only reads out
the pipe -> shared dpll association thus far. Other state which needs
to follow:
- hw state of the dpll (on/off + dpll registers). Currently we just
read that out from the hw state, but that doesn't work too well when
the dpll is in use, but not yet fully enabled. We get away since
most likely it already has been enabled and so the correct state is
left behind in the registers. But that doesn't hold for atomic
modesets when we want to enable all pipes at once.
- Refcount reconstruction for each dpll.
- Cross-checking of all the above. For that we need to keep the dpll
register state both in the pipe and in the shared_dpll struct, so
that we can check that every pipe is still connected to a correctly
configured dpll.
Note that since the refcount resconstruction isn't done yet this will
spill a few WARNs at boot-up while trying to disable pch plls which
have bogus refcounts. But since there's still a pile of refactoring to
do I'd like to lock down the state handling as soon as possible hence
decided against reordering the patches to quiet these WARNs - after
all the issues they're complaining about have existed since forever,
as Jesse can testify by having pch pll states blow up consistently in
his fastboot patches ...
v2: We need to preserve the old shared_dpll since currently the
shared dpll refcount dropping/getting is done in ->mode_set. With
the usual pipe_config infrastructure the old dpll id is already lost
at that point, hence preserve it in the new config.
v3: Rebase on top of the ips patch from Paulo.
v4: We need to unconditionally take over the shared_dpll id from the
old pipe config when e.g. doing a direct pch port -> cpu edp
transition.
v5: Move the saving of the old shared_dpll id to an ealier patch.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bits are evenly space, so we can cut down on two big switch
blocks. This also greatly simplifies the hw state readout which
follows in the next patch.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the big sed-job prep work done this is now really simple. With
the exception that we only assign the right shared dpll id in the
->mode_set callback but also depend upon the old one still being
around.
Until that mess is fixed up we need to jump through a few hoops to
keep the old value save.
v2: Kill the funny whitespace spotted by Chris.
v3: Move the shared_dpll pipe config fixup into this patch as noticed
by Ville. Also unconditionally set the shared_dpll with the current
one, since otherwise we won't handle direct pch port -> cpu edp
transitions correctly.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Dealing with discrete enum values is simpler for hw state readout and
pipe config computations than pointers - having neat names instead of
chasing pointers should look better in the code.
This isn't a that good reason for pch plls, but on haswell we actually
have 3 different types of plls: WRPLL, SPLL and the DP clocks. Having
explicit names should help there.
Since this also adds the intel_crtc_to_shared_dpll helper to further
abstract away the crtc -> dpll relationship this will also help to
make the next patch simpler, which moves the shared dpll into the pipe
configuration.
Also note that for uniformity we have two special dpll ids: NONE for
pipes which need a shared pll but don't have one (yet) and private for
when there's a non-shared pll (e.g. per-pipe or per-port pll).
I've thought whether we should also add a 2nd enum for the type of the
pll we want (for really generic pll selection code) but thrown that
idea out again - likely there's too much platform craziness going on
to be able to share the pll selection logic much.
Since this touched all the shared_pll functions a bit I've also done
an s/intel_crtc/crtc/ replacement on a few of them.
v2: Kill DPLL_ID_NONE. It's probably better to call it DPLL_ID_INVALID and use
it to check that the compute config stage assigns a dpll to every pipe.
But since that code isn't ready yet until we move the dpll selection out
of the ->mode_set callback, there's no use for it.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For fastboot we need some support to read out the sharing state of
plls, at least for platforms where they can be shared (or freely
assigned at least). Now for ivb we already have pretty extensive
infrastructure for tracking pch plls, and it took us an aweful lot of
tries to get that remotely right. Note that hsw could also share plls,
but even now they're already freely assignable. So we need this on
more than just ivb.
So on top of the usual fastboot fun pll sharing seems to be an
additional step up in fragility. Hence a common infrastructure for all
shared/freely assignable display plls seems to be in order.
The plan is to have a bit of dpll hw state readout code, which can be
used individually, but also to fill in the pipe config. The hw state
cross check code will then use that information to make sure that
after every modeset every pipe still is connected to a pll which still
has the correct configuration - a lot of the pch pll sharing bugs
where due to incorrect sharing.
We start this endeavour with a simple s/pch_pll/shared_dpll/ rename
job.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before I start to make a complete mess out of this, crank up
the paranoia level a bit.
v2: Kill the has_pch_encoder check in put_shared_dpll - it's invalid
as spotted by Ville since we currently only put the dpll when we
already have the new pipe config. So a direct pch port -> cpu edp
transition will hit this.
v3: Now that I've lifted my blinders add the WARN_ON Ville requested.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Simlar to how disable already works on haswell. This is possible
since we now carefully track the pch state in the pipe config.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We ->mode_set is called we can't just blindly reuse an existing pll
since that might be shared with a different, still active pch output.
v2: Only update the pll settings when the pch pll is know to be
unused, otherwise we can wreak havoc with a running pipe. Which in the
case of DP will likely result in a black screen due to loss of link
lock.
v3: Tighten up the asserts a bit more, especially make sure that the
pch pll is still enabled when we try to disable it. This would have
caught the bug fixed in this patch.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This makes, arguably, the condition on state easier to read.
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In
commit 53d3b4d777
Author: Egbert Eich <eich@suse.de>
Date: Tue Jun 4 17:13:21 2013 +0200
drm/i915/sdvo: Use &intel_sdvo->ddc instead of intel_sdvo->i2c for DDC
Egbert Eich fixed a long-standing bug where we simply used a
non-working i2c controller to read the EDID for SDVO-LVDS panels.
Unfortunately some machines seem to not be able to cope with the mode
provided in the EDID. Specifically they seem to not be able to cope
with a 4x pixel mutliplier instead of a 2x one, which seems to have
been worked around by slightly changing the panels native mode in the
VBT so that the dotclock is just barely above 50MHz.
Since it took forever to notice the breakage it's fairly safe to
assume that at least for SDVO-LVDS panels the VBT contains fairly sane
data. So just switch around the order and use VBT modes first.
v2: Also add EDID modes just in case, and spell Egbert correctly.
v3: Elaborate a bit more about what's going on on Chris' machine.
Cc: Egbert Eich <eich@suse.de>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65524
Cc: stable@vger.kernel.org
Reported-and-tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The hotplug_mask is no longer used as the hpd interrupt setup is now
handled in the core.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
sdvo->hotplug_active is initialised during intel_sdvo_setup_outputs(),
and so we never enabled the hotplug interrupts on SDVO as we were
checking too early.
This regression has been introduced somewhere in the hpd rework for
the storm detection and handling starting with
commit 1d843f9de4
Author: Egbert Eich <eich@suse.de>
Date: Mon Feb 25 12:06:49 2013 -0500
DRM/I915: Add enum hpd_pin to intel_encoder.
and the follow-up patches to use the new encoder->hpd_pin variable for
the different irq setup functions.
The problem is that encoder->hpd_pin was set up _before_ the output
setup was done and so before we could assess the hotplug capabilities
of the outputs on an sdvo encoder.
Reported-by: Alex Fiestas <afiestas@kde.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=58405
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add regression note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A broken conditional would lead to SDVOC waiting upon hotplug events on
SDVOB - and so miss all activity on its SDVO port.
This regression has been introduced in
commit 1d843f9de4
Author: Egbert Eich <eich@suse.de>
Date: Mon Feb 25 12:06:49 2013 -0500
DRM/I915: Add enum hpd_pin to intel_encoder.
References: https://bugs.freedesktop.org/show_bug.cgi?id=58405
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add regression note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Don't enable the cursor until g4x_fixup_plane() had a chance to do
cast its magic spell.
Egbert writes:
"Today I had the chance to test this. First I tried
if I can still reproduce the blank with this patch
added when I disable my voodoo g4x_fixup_plane():
It turned out it still happens however very rarely
(like 1 out of 20 tries). When I reenabled my voodoo
the issue still occurred.
I had to switch two lines around, ie:
intel_enable_plane(dev_priv, plane, pipe);
if (IS_G4X(dev))
g4x_fixup_plane(dev_priv, pipe);
+ intel_crtc_update_cursor(crtc, true);
to avoid the blank screen issue - which is it didn't
happen in ~75 tries."
v2: Add a comment to remind people of the ordering constraints
Acked-by: Egbert Eich <eich@suse.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WaFbcNukeOn3DBlt for IVB, HSW.
According BSPec: "Workaround: Do not enable Render Command Streamer tracking for FBC.
Instead insert a LRI to address 0x50380 with data 0x00000004 after the PIPE_CONTROL that
follows each render submission."
v2: Chris noticed that flush_domains check was missing here and also suggested to do
LRI only when fbc is enabled. To avoid do a I915_READ on every flush lets use the
module parameter check.
v3: Adding Wa name as Damien suggested.
v4: Ville noticed VLV doesn't support fbc at all and comment came wrong from spec.
v5: Ville noticed than on blt a Cache Clean LRI should be used instead the Nuke one.
v6: Check for flush domain on blt (by Ville).
Check for scanout dirty (by Chris).
v7: Apply proper fbc_dirty implemented by Chris.
v8: remove unused variables.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is required for tracking render damage for use with FBC and will be
used in subsequent patches.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pull the code to disable trickle feed for all primary planes into a
separate function.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We disable trickle feed in all the (relevant) clock gating functions,
except ironlake_init_clock_gating(). Copy paste the same code there as
well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to BSpec, trickle feed should be disabled for BW and
mobile CL. Those constraints seem to match all of our gen4 chipsets.
Trickle feed is disabled via the MI_ARB_STATE register instead of
per plane controls on gen4.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The docs say that the trickle feed disable bit is present (for primary
planes only, not video sprites) on CTG, and that it must be set
for ELK. Just set it for all g4x chipsets.
v2: Do it in init_clock_gating too
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We always limited the link bw calculations to 24bpp. Tested with
my shiny new high-bpc screen, seems to work as advertised.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=65280
Tested-by: shui yangwei <yangweix.shui@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For various reasons the hw state readout might not be able to
faithfully match the hw state:
- broken hw (like the case which motivated this patch here where the
sdvo encoder does not implemented mandatory functionality
correctly).
- platforms which are not supported fully with the pipe config
infrastructure
- if our code doesn't support a given hw configuration natively, e.g.
special restrictions on the per-pipe panel fitters when they're used
in high-quality scaling modes.
In all these cases both fastboot and the hw state cross checker need
to be aware of these cases and act accordingly. To be able to do this
add a new quirk flag to the pipe config structure.
The specific case at hand is an sdvo encoder which doesn't implement
the get_timings function, so adjusted_mode flags will be wrong. The
strange thing though is that the encoder _does_ work, even though it
doesn't implement any of the timings functions (so neither get nor
set, neither for input nor output timings).
Not that non-compliant sdvo encoder are any surprise at all ...
v2:
- Don't read random garbage from the dtd if the get_timings call
failed (suggested by Chris).
- Still check the interlaced flag, that's read out from someplace
else. We want maximal paranoia, after all.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell Display audio depends on power well in graphic side, it should
request power well before use it and release power well after use.
I915 will not shutdown power well if it detects audio is using.
This patch protects display audio crash for Intel Haswell C3 stepping board.
Signed-off-by: Wang Xingchao <xingchao.wang@linux.intel.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
CTG/ILK/SNB/IVB support 4kx2k surfaces. HSW supports 4kx4k, but
without proper front buffer invalidation on the last 2k lines, so
don't enable FBC on these cases for now.
v2: Use gen >= 5, not gen > 4 (Daniel).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Incomplete since ilk+ support needs proper pch dpll tracking first.
SDVO get_config parts based on a patch from Jesse Barnes, but fixed up
to actually work.
v2: Make sure that we call encoder->get_config _after_ we
get_pipe_config to be consistent in both setup_hw_state and the
modeset state checker. Otherwise the clever trick with handling the
pixel mutliplier on i915G/GM where the encoder overrides the default
value of 1 from the crtc get_pipe_config function doesn't work.
Spotted by Imre Deak.
v3: Actually cross-check the pixel mutliplier (but not on pch split
platforms for now). Now actually also tested on a i915G with a sdvo
encoder plugged in.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Adding more context from Ville's reply to Rodrigo's question why we
need this:
"The spec says that on some hardware you need to PLL running before you
can poke at the palette registers. I didn't actually try to anger the
hardware so I'm not really sure what would happen otherwise, but IIRC
Jesse said something about a hard system hang..."
And generally documenting such ordering constraints with asserts is
Just Good.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Spruce up the commit message a lot.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make assert_sprites_disabled() operational on all platforms where
we currently have sprite support enabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ever since gen4 primary planes were fixed to pipes.
And for gen2-3, don't check plane B if it doesn't exist.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Disable/restore sprite planes around mode-set just like we do for the
primary and cursor planes. Now that we have working sprite clipping,
this actually works quite decently.
Previosuly we didn't even bother to disable sprites when changing mode,
which could lead to a corrupted sprite appearing on the screen after a
modeset (at least on my IVB). Not sure if all hardware generations would
be so forgiving when enabled sprites end up outside the pipe dimensons.
v2: Disable rather than enable sprites in ironlake_crtc_disable()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV doesn't have the old video overlay.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
First disable FBC, then IPS, then disable all planes, and finally
disable the pipe.
v2: Mention IPS in the commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Again follow the same sequence for all generations, because doing
otherwise just doesn't make sense.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the same sequence when enabling the cursor plane during
modeset. No point in doing this stuff in different order on different
generations.
This should also avoid a needless wait for vblank for the g4x cursor
workaround when the cursor gets enabled anyway.
Acked-by: Egbert Eich <eich@suse.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Loading the palette after the planes are enabled can risk showing
incorrect colors. ILK+ already load the palette before even the pipe
is enabled. Just follow the same order for gen2-4 and VLV.
According to BSpec the requirements for palette access are
display core clock and display PLL running. In certain platforms
just the core clock may be enough. But we definitely should have both
running when this gets called during the modeset.
v2: Amend the commit message with some display PLL/core clock info
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We use port I/O for VGA register access, so adding display_mmio_offset
is just wrong.
This reverts commit 56a12a5092.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So we can remove some duplicate code. All the PCHs are very similar
and right now the code is the same. I plan to add more code, so we
would have more duplicated code.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By stashing a pointer of who opened the device and keeping a list of
open fd, we can then walk each client and inspect how many objects they
have open. For example,
i915_gem_objects:
1102 objects, 613646336 bytes
663 [662] objects, 468783104 [468750336] bytes in gtt
37 [37] active objects, 46874624 [46874624] bytes
626 [625] inactive objects, 421908480 [421875712] bytes
282 unbound objects, 6512640 bytes
85 purgeable objects, 6787072 bytes
28 pinned mappable objects, 3686400 bytes
40 fault mappable objects, 27783168 bytes
2145386496 [536870912] gtt total
Xorg: 43 objects, 32243712 bytes (10223616 active, 16683008 inactive, 4096 unbound)
gnome-shell: 30 objects, 28381184 bytes (0 active, 28336128 inactive, 0 unbound)
xonotic-linux64: 1032 objects, 569933824 bytes (46874624 active, 383545344 inactive, 6508544 unbound)
v2: Use existing drm->filelist as pointed out by Ben.
v3: Not even stashing the task_struct is required as Ben pointed out
drm_file->pid.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This way we can simplify the code quite a bit.
Also add a WARN in the sdvo code to complain about a bogus value
and kill the readout code in intel_ddi.c that Jesse sneaked in.
HW state readout for the pixel multiplier will work a bit differently
in the end.
v2: Rebase on top of the fdi pixel mutliplier handling fix.
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Two exactly same error messages on different error paths makes debugging
difficult. Clarify the messages and distinguish them from each other.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only lvds/tv did actually check for cloning or not, but many more
places should.
Notices because my ivb tried to enable both cpu edp and vga on the
first crtc - the resulting confusion between has_pch_encoder,
has_dp_encoder but not actually being a pch dp encoder resulting in
hilarity (hitting a BUG).
We _really_ need an igt to random-walk our modeset space more
exhaustively.
The bug seems to have been exposed due to a race in the hw load
detection support for VGA: Right after a hotplug VGA was still
detected as connected, but obviously reading the EDID wasn't possible
any more. Hence why restarting X a bit later fixed things. Due to the
1024x756 fallback resolution suddenly more outputs had the same
resolution.
On top of that SNA was confused with the possible_clones mask, trying
to clone outputs which cannot be cloned. That bug is now fixed with
commit fc1e0702b25e647cb423851fb7228989fec28bd6
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed May 29 11:25:28 2013 +0100
sna: fixup up possible_clones kms->X impedance mismatch
v2: Kill intel_encoder_check_is_cloned, spotted by Paulo.
v3: Drop the now unused pipe param.
v4: Kill the stray printk Chris spotted.
v5: Elaborate on how the bug in userspace happened and why it was racy
to reproduce.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix the DSPCLK_GATE_D access for VLV. The code incorrectly tried to
poke at the ILK+ version of the register which is at the wrong offset.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The LP watermark registers don't exist on VLV, so don't touch them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In intel_sdvo_get_lvds_modes() the wrong i2c adapter record is used
for DDC. Thus the code will always have to rely on a LVDS panel
mode supplied by VBT.
In most cases this succeeds, so this didn't get detected for quite
a while.
This regression seems to have been introduced in
commit f899fc64cd
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Jul 20 15:44:45 2010 -0700
drm/i915: use GMBUS to manage i2c links
Signed-off-by: Egbert Eich <eich@suse.de>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Add note about which commit likely introduced this issue.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Panel fitters on ivb/hsw are not created equal since not all of them
support the new high-quality upscaling mode. To offset this the hw
allows us to freely assign the pfits to pipes.
Since our code currently doesn't support this we might fall over when
taking over firmware state. So check for this case and WARN about it.
We can then improve the code once we've hit this in the wild. Or once
we decide to support the improved upscale modes, though that requires
global arbitrage of modeset resources across crtcs.
v2: Check for IS_GEN7 instead of IS_IVB || IS_HSW as suggested by
Paulo in his review comment.
Suggested-by: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We can get at this easily through intel_crtc->config now.
v2: Drop more stuff gcc spotted.
v3: Drop even more stuff gcc spotted.
v4: Yet more ...
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... not the port clock. This allows us to kill the funny semantics
around pixel_target_clock.
Since the dpll code still needs the real port clock, add a new
port_clock field to the pipe configuration. Handling the default case
for that one is a bit tricky, since encoders might not consistently
overwrite it when retrying the crtc/encoder bw arbitrage step in the
compute config stage. Hence we need to always clear port_clock and
update it again if the encoder hasn't put in something more specific.
This can't be done in one step since the encoder might want to adjust
the mode first.
I was a bit on the fence whether I should subsume the pixel multiplier
handling into the port_clock, too. But then I decided against this
since it's on an abstract level still the dotclock of the adjusted
mode, and only our hw makes it a bit special due to the separate pixel
mulitplier setting (which requires that the dpll runs at the
non-multiplied dotclock).
So after this patch the adjusted_mode accurately describes the mode we
feed into the port, after the panel fitter and pixel multiplier (or
line doubling, if we ever bother with that) have done their job.
Since the fdi link is between the pfit and the pixel multiplier steps
we need to be careful with calculating the fdi link config.
v2: Fix up ilk cpu pll handling.
v3: Introduce an fdi_dotclock variable in ironlake_fdi_compute_config
to make it clearer that we transmit the adjusted_mode without the
pixel multiplier taken into account. The old code multiplied the the
available link bw with the pixel multiplier, which results in the same
fdi configuration, but is much more confusing.
v4: Rebase on top of Imre's is_cpu_edp removal.
v5: Rebase on top of Paulo's haswell watermark fixes, which introduce
a new place which looked at the pixel_clock and so needed conversion.
v6: Split out prep patches as requested by Paulo Zanoni. Also rebase
on top of the fdi dotclock handling fix in the fdi lanes/bw
computation code.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v3)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v6)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This prepares a bit for the next big patch, where we switch the
semantics of the different clocks in the pipe config around.
Since I've broken cpu eDP PLL handling in the first version I've
figured some refactoring is in order.
Split out on request from Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We currently mutliply the link_bw of the fdi link with the pixel
multiplier, which is wrong: The FDI link doesn't suddenly grow more
bandwidth. In reality the pixel mutliplication only happens in the PCH,
before the pixels are fed into the port.
But since we our code treats the uses the target clock after pixels
are doubled (tripled, ...) already, we need to correct this.
Semantically it's clearer to divide the target clock to get the fdi
dotclock instead of multiplying the bw, so do that instead.
Note that the target clock is already multiplied by the same factor,
so the division will never loose accuracy for the M/N computation.
The lane computation otoh used the wrong value, we also need to feed
the fdi dotclock to that.
Split out on a request from Paulo Zanoni.
v2: Also fix the lane computation, it used the target clock to compute
the bw requirements, not the fdi dotclock (i.e. adjusted with the
pixel multiplier). Since sdvo only uses the pixel multiplier for
low-res modes (with a dotclock below 100MHz) we wouldn't ever have
rejected a bogus mode, but just used an inefficient fdi config.
v3: Amend the commit message to explain better what the change for the
fdi lane config computation is all about. Requested by Paulo.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since I stand by my rule that splitting functions should only do an
exact copy, this is a follow-up patch.
Suggested-by: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that the DP madness is cleared out, this is all only per-platform.
So move it out from the intel clock limits structure.
While at it drop the intel prefix on the static functions, call the
vtable entry find_dpll (since it's for the display pll) and rip out
the now unnecessary forward declarations.
Note that the parameters of ->find_dpll are still unchanged, but they
eventually need to be moved over to just take in a pipe configuration.
But currently a lot of things are still missing from the pipe
configuration (reflock, output-specific dpll limits and preferences,
downclocked dotclock). So this will happen in a later step.
Note that intel_g4x_limit has a peculiar case where it selects
intel_limits_i9xx_sdvo as the limit. This is pretty bogus and also not
used since the only output types left are DP and native TV-out which
both use special pre-tuned dpll values.
v2: Re-add comment for the find_pll callback (requested by Paulo) and
elaborate on why the transformation is correct for g4x platforms (to
clarify a review question from Paulo). Double up on that by adding a
WARN as suggested by Paulo Zanoni on irc.
v3: Initialize limits to NULL since gcc is now unhappy.
v4: v2/3 will blow up with a NULL dereference in ->find_dpll for dp and
TV-out ports, spotted by Paulo on irc. So just give up on this madness for
now, and leave this to be fixed in a later patch.
v5: Since the ever-so-slight change for g4x might result in some dpll
parameter computation failing spuriously where before it didn't for
ports with preset dpll settings (DP & TV-out) override this. For
paranoia also do it in the ilk+ code.
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pineview is just different.
Also split out i9xx_clock from intel_clock and drop the now redundant
struct device * parameter.
Note that in this patch I kill an XXX comment about 100MHz clocks. I
couldn't figure out what this is about, and we don't seem to have any
bug reports about this either. I suspect that it's a remnant from when
the i9xx and ilk+ modeset code was all in the same file since ilk+
does indeed have a 100MHz clock. So I've just killed it to stop the
cargo-culting.
Reviewed-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since this is run in the compute config stage we need to check
the new_ pointers, i.e the stage output routing, not the current
modeset layout. Also there was a little logic bug in properly skipping
connectors: The old code did not skip any unused connectors and so
clamped to whatever was left in there (usually 0 if that connector
hasn't seen a EDID 1.4 screen ever since boot-up).
This has been broken when moving the pipe bpp selection in
commit 4e53c2e010
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Wed Mar 27 00:44:58 2013 +0100
drm/i915: precompute pipe bpp before touching the hw
To avoid too much casting switch from drm_ to intel_ types.
Also add a bit of debug output to help reconstructing what's going
on.
v2: Try to clarify this a bit:
- s/pipe_config_set_bpp/compute_baseline_pipe_bpp/ to make it clearer
at which stage this function is run. Also add a comment about what
it does.
- Extract the sink clamping into it's own function.
v3: Actually make it compile.
v4: Split out all the prep refactoring to make the bugfix stick out
really badly. Also elaborate a bit in the commit message about the
nature of the bugfix.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As a prep work to fix it up:
- Use intel_connector instead of drm_connector to avoid too much
upcasting in the bugfix patch.
- Extract the connector bpp clamping from the loop-over-connectors
logic.
- Bikeshed function names (to make it clearer that
acompute_baseline_pipe_bpp runs in the compute stage of the modeset
sequence) and add a comment to make it clearer what it does.
No functional change in this patch.
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Last year, a patch was made for the "HP t5740e Thin Client" (see
http://lists.freedesktop.org/archives/dri-devel/2012-May/023245.html).
This device reports an lvds panel, but does not really have one.
The predecessor of this device is the "hp t5740", which also does not have
an lvds panel. This patch will add the same quirk for this device.
Signed-off-by: Ben Mesman <ben@bnc.nl>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we always force the pipe A to on we can't use the hw state to
decide whether it should be on. Hence quirk the quirk.
The problem is that crtc->active tracks the state of the entire
display pipe, i.e. including planes, encoders and all. But our hw
state readout simply looks at the pipe. But with the pipe A quirk we
force-enable that (together with it's pll). To fix that mismatch we
have two options:
- Quirk the checked state to match what our sw tracking states if the
pipe A quirk is in effect.
- Improve the hw state readout to not get fooled by the pipe A quirk.
Since we already have similar state clamping in e.g. assert_pipe I've
opted for the first variant. Also note that we don't really loose any
state checking: Individual pieces of the abstract crtc pipe are
checked in the enable/disable functions with the various asssert_*
checks we have, and the hw state check code doesn't check anything if
the pipe is off anyway.
v2: Pimp commit message after discussion with Chris and only apply the
quirk for the quirk if we're checking pipe A. Otherwise we'll miss
state checking for pipe B on i830M ...
v3: Make the code comment consistent with the improved commit message,
too (Chris).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=64764
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reported-and-Tested-by: mlsemon35@gmail.com (v1)
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Chris Wilson noticed that since
commit 1f83fee08d [v3.9]
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Nov 15 17:17:22 2012 +0100
drm/i915: clear up wedged transitions
X can again get -EIO when it does not expect it. And even worse score
a SIGBUS when accessing gtt mmaps. The established ABI is that we
_only_ return an -EIO from execbuf - all other ioctls should just
work. And since the reset code moves all bos out of gpu domains and
clears out all the last_seqno/ring tracking there really shouldn't be
any reason for non-execbuf code to ever touch the hw and see an -EIO.
After some extensive discussions we've noticed that these spurios -EIO
are caused by i915_gem_wait_for_error:
http://www.mail-archive.com/intel-gfx@lists.freedesktop.org/msg20540.html
That is easy to fix by returning 0 instead of -EIO, since grabbing the
dev->struct_mutex does not yet mean that we actually want to touch the
hw. And so there is no reason at all to fail with -EIO.
But that's not the entire since, since often (at least it's easily
googleable) dmesg indicates that the reset fails and we declare the
gpu wedged. Then, quite a bit later X wakes up with the "Timed out
waiting for the gpu reset to complete" DRM_ERROR message in
wait_for_errror and brings down the desktop with an -EIO/SIGBUS.
So clearly we're missing a wakeup somewhere, since the gpu reset just
doesn't take 10 seconds to complete. And indeed we're do handle the
terminally wedged state wrong.
Fix this all up.
References: https://bugs.freedesktop.org/show_bug.cgi?id=63921
References: https://bugs.freedesktop.org/show_bug.cgi?id=64073
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We only need to do them if the pipe is actually running and if the
framebuffers have changed. Removes two "wait for vblank timed out"
messages when doing a suspend/resume cycle on my i855gm.
v2: s/to_intel_ctrc(crtc)/intel_crtc/ spotted by Chris.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
People don't like typedefs these days. Eliminate their use from intel_fb.c.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use container_of() instead of a cast to get struct intel_fbdev
from struct drm_fb_helper.
Also populate the fb_info->par correctly with the drm_fb_helper pointer
instead of the intel_fbdev pointer.
There's no actual functional change since the drm_fb_helper happens to
be the first member inside intel_fbdev.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rework of per ring hangcheck made this obsolete.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Keep track of ring seqno progress and if there are no
progress detected, declare hang. Use actual head (acthd)
to distinguish between ring stuck and batchbuffer looping
situation. Stuck ring will be kicked to trigger progress.
This commit adds a hard limit for batchbuffer completion time.
If batchbuffer completion time is more than 4.5 seconds,
the gpu will be declared hung.
Review comment from Ben which nicely clarifies the semantic change:
"Maybe I'm just stating the functional changes of the patch, but in case
they were unintended here is what I see as potential issues:
1. "If ring B is waiting on ring A via semaphore, and ring A is making
progress, albeit slowly - the hangcheck will fire. The check will
determine that A is moving, however ring B will appear hung because
the ACTHD doesn't move. I honestly can't say if that's actually a
realistic problem to hit it probably implies the timeout value is too
low.
2. "There's also another corner case on the kick. If the seqno = 2
(though not stuck), and on the 3rd hangcheck, the ring is stuck, and
we try to kick it... we don't actually try to find out if the kick
helped"
v2: use atchd to detect stuck ring from loop (Ben Widawsky)
v3: Use acthd to check when ring needs kicking.
Declare hang on third time in order to give time for
kick_ring to take effect.
v4: Update commit msg
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net>
[danvet: Paste in Ben's review comment.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since it will be used for the global bound/unbound list with full PPGTT,
this helps clarify things for upcoming code rework.
Recommended-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we properly keep track of the pages_pin_count, then when we later add
multiple address spaces, the put_pages doesn't need any special checks
to be able to perform it's job.
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Rebased on top of the fix for stolen memory pinning.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The way the stolen handling works is we take a pin on the backing pages,
but we never actually get a reference to the bo. On freeing objects
allocated with stolen memory, the final unref will end up freeing the
object with pinned pages count left. To enable an assertion to catch
bugs in this code path, this patch cleans up that remaining pin.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's not terribly interesting to know that a parameter doesn't exist,
and it can get in the way of interesting messages, especially with the
staggered VECS merging as we've done.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It just prints whether it's supported/enabled/disabled. Feature
requested by the power management team.
v2: Checkpatch started complaining about seq_printf with 1 argument.
Requested-by: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IPS is still enabled by default. Feature requested by the power
management team.
This should also help testing the feature on some early pre-production
hardware where there were relationship problems between IPS and PSR.
v2: Rebase on top of the newest IPS implementation.
v3: Check i915_enable_ips at compute_config, not supports_ips, so the
kernel parameter will be ignored at haswell_get_pipe_config.
Requested-by: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Intermediate Pixel Storage is a feature that should reduce the number
of times the display engine wakes up memory to read pixels, so it
should allow deeper PC states. IPS can only be enabled on ULT pipe A
with 8:8:8 pipe pixel formats.
With eDP 1920x1080 and correct watermarks but without FBC this moves
my PC7 residency from 2.5% to around 38%.
v2: - It's tied to pipe A, not port A
- Add pipe_config support (Chris)
- Add some assertions (Chris)
- Rebase against latest dinq
v3: - Don't ever set ips_enabled to false (Daniel)
- Only check for ips_enabled at hsw_disable_ips (Daniel)
v4: - Add hsw_compute_ips_config (Daniel)
- Use the new dump_pipe_config (Daniel)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that we track the cpu transcoder we need accurately in the pipe
config we can finally fix up the transcoder check. With the current
code eDP on port D will be broken since we'd errornously cut the
power.
For reference see
commit 2124b72e62
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Fri Mar 22 14:07:23 2013 -0300
drm/i915: don't disable the power well yet
v2:
- Kill the now outdated comment (Paulo)
- Add the missing crtc->base.enabled check and consolidate it (Paulo)
- Smash all checks together, looks neater that way.
v3: Kill the unused encoder variable.
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This will let userland only try to use the new ring
when the appropriate kernel is present
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A user can run batchbuffer via VEBOX ring.
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Removed rebase relic VECS ring from i915_gem_request_info (Damien)
v3: s/hsw/hws in debugfs which I introduced in v2 (Jon)
Signed-off-by: Xiang, Haihao <haihao.xiang@intel.com>
[Order changed, and modified by]
CC: "Bloomfield, Jon" <jon.bloomfield@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Similar to a patch originally written by:
v2: Reversed the meanings of masked and enabled (Haihao)
Made non-destructive writes in case enable/disabler rps runs first
(Haihao)
v3: Reword error message (Damien)
Modify postinstall to do the right thing based on previous fixup. (Ben)
CC: Xiang, Haihao <haihao.xiang@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Use the correct lock to protect PM interrupt regs, this was
accidentally lost from earlier (Haihao)
Fix return types (Ben)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The motivation here is we're going to add some new interrupt definitions
and handling outside of the GT interrupts which is all we've managed so
far (with some RPS exceptions). By consolidating the names in the future
we can make thing a bit cleaner as we don't need to define register
names twice, and we can leverage pretty decent overlap in HW registers
since ILK.
To explain briefly what is in the comments: there are two sets of
interrupt masking/enabling registers. At least so far, the definitions
of the two sets overlap. The old code setup distinct names for
interrupts in each set, ie. one for global, and one for ring. This made
things confusing when using the wrong defines in the wrong places.
rebase: Modified VLV bits
v2: Renamed GT_RENDER_MASTER to GT_RENDER_CS_MASTER (Damien)
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's overkill on older gens, but it's useful for newer gens.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
PM interrupts have an expanded role on HSW. It helps route the EBOX
interrupts. This patch is necessary to make the existing code which
touches the mask, and enable registers more friendly to other code paths
that also will need these registers.
To be more explicit:
At preinstall all interrupts are masked and disabled. This implies that
preinstall should always happen before any enabling/disabling of RPS or
other interrupts.
The PMIMR is touched by the workqueue, so enable/disable touch IER and
IIR. Similarly, the code currently expects IMR has no use outside of the
RPS related interrupts so they unconditionally set 0, or ~0. We could
use IER in the workqueue, and IMR elsewhere, but since the workqueue
use-case is more transient the existing usage makes sense.
Disable RPS events:
IER := IER & ~GEN6_PM_RPS_EVENTS // Disable RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Disable any outstanding interrupts
Enable RPS events:
IER := IER | GEN6_PM_RPS_EVENTS // Enable the RPS related interrupts
IIR := GEN6_PM_RPS_EVENTS // Make sure there were no leftover events
(really shouldn't happen)
v2: Shouldn't destroy PMIIR or PMIMR VEBOX interrupt state in
enable/disable rps functions (Haihao)
v3: Bug found by Chris where we were clearing the wrong bits at rps
disable.
expanded commit message
v4: v3 was based off the wrong branch
v5: Added the setting of PMIMR because of previous patch update
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the moment, these values are wiped out anyway by the rps
enable/disable. That will be changed in the next patch though.
v2: Add post install setup to address issue found by Damien in the next
patch.
replaced
WARN_ON(dev_priv->rps.pm_iir != 0);
with rps.pm_iir = 0;
With the v2 of this patch and the deferred pm enabling (which changed
since the original patches) we're now able to get PM interrupts before
we've brought up enabled rps. At this point in boot, we don't want to do
anything about it, so we simply ignore it. Since writing the original
assertion, the code has changed quite a bit, and I believe removing this
assertion is perfectly safe.
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: I don't agree with the justification to drop the WARN and
added a FIXME to that effect.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HSW has some special requirements for the VEBOX. Splitting out the
interrupt handler will make the code a bit nicer and less error prone
when we begin to handle those.
The slight functional change in this patch (queueing work while holding
the spinlock) is intentional as it makes a subsequent patch a bit nicer.
The change should also only effect HSW platforms.
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now we compute the results for both 1/2 and 5/6 partitioning and then
use hsw_find_best_result to choose which one to use.
With this patch, Haswell watermarks support should be in good shape.
The only improvement we're missing is the case where the primary plane
is disabled: we always assume it's enabled, so we take it into
consideration when calculating the watermarks.
v2: - Check the latency when finding the best result
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
