With the patch to support MMUv3, the base address for the loaded
binary image has changed, and a fix was applied to the U-Boot image.
This fixes the RedBoot image.
Signed-off-by: Chris Zankel <chris@zankel.net>
IRQ handlers are expected to run with IRQs disabled.
See e.g. http://lwn.net/Articles/380931/ for a longer story.
This was overlooked in the commit
2d1c645 xtensa: dispatch medium-priority interrupts
Revert to old behavior and simplify interrupt entry and exit code.
Interrupt handler still honours IRQ priority.
do_notify_resume/schedule must be called with interrupts enabled, enable
interrupts if we return from user exception.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
IRQs are disabled when PS.EXCM is set or PS.INTLEVEL is equal to or
higher than LOCKLEVEL.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Definition of CALLER_ADDR* through __builtin_return_address makes
compiler insert calls to __xtensa_libgcc_window_spill, which in turn
makes fast_syscall_spill_registers syscall that clobbers registers when
called from the kernel mode, leading to invalid opcode exceptions on
return to userspace.
Provide definition for CALLER_ADDR0 as MAKE_PC_FROM_RA(a0, a1) and in
case CONFIG_FRAME_POINTER is enabled extract CALLER_ADDR{1-3} from
stack.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
- remove unused asm parameters;
- fix EXCM bit setting in the PS SR during _spill_registers call.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
To support FRAME_POINTER avoid using a7 in __simc (none of the existing
simcalls needs it). Replace calls to __simc with more specific
simc_read, simc_write and simc_lseek calls.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
This fixes the following build error:
arch/xtensa/kernel/built-in.o:(.init.literal+0xe8): undefined reference
to `platform_pcibios_init'
arch/xtensa/kernel/built-in.o: In function `setup_arch':
(.init.text+0x20e): undefined reference to `platform_pcibios_init'
and allows platform to omit definition of platform_pcibios_init if it's
empty.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
The Kconfig symbol KCORE_ELF was removed in v2.6.0, but reappeared in two
architectures. It is useless. Remove it again.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Only set the register when there is at least one ibreak register,
otherwise the build fails:
arch/xtensa/kernel/head.S:105: Error: invalid register 'ibreakenable'
for 'wsr' instruction
arch/xtensa/platforms/iss/setup.c:67: Error: invalid register
'ibreakenable' for 'wsr' instruction
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Chris Zankel <chris@zankel.net>
Fix access_ok macro no to permit
case where user will try to access
the last address space which is equal
to segment address.
Example:
segment addr = 0xbfff ffff
address = 0xbfff fff0
size = 0x10
Current wrong implementation
0xbfff ffff >= (0xbfff fff0 | 0x10 | (0xbfff fff0 + 0x10))
0xbfff ffff >= (0xbfff fff0 | 0xc000 0000)
0xbfff ffff >= 0xf000 0000
return 0 which is access failed even the combination is valid.
because get_fs().seq returns the last valid address.
This patch fix this problem.
Size equals to zero is valid access.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Register the irq_domain created during initialization as the default so
that device drivers can pass NULL to irq_create_mapping and get a
virtual irq to pass to request_irq.
Signed-off-by: Dan Christensen <opello@opello.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A race condition exists when registering the first watchdog device.
Sequence of events:
- watchdog_register_device calls watchdog_dev_register
- watchdog_dev_register creates the watchdog misc device by calling
misc_register.
At that time, the matching character device (/dev/watchdog0) does not yet
exist, and old_wdd is not set either.
- Userspace gets an event and opens /dev/watchdog
- watchdog_open is called and sets wdd = old_wdd, which is still NULL,
and tries to dereference it. This causes the kernel to panic.
Seen with systemd trying to open /dev/watchdog immediately after
it was created.
Reported-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Arkadiusz Miskiewicz <arekm@maven.pl>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The invalid guest state emulation loop does not check halt_request
which causes 100% cpu loop while guest is in halt and in invalid
state, but more serious issue is that this leaves halt_request set, so
random instruction emulated by vm86 #GP exit can be interpreted
as halt which causes guest hang. Fix both problems by handling
halt_request in emulation loop.
Reported-by: Tomas Papan <tomas.papan@gmail.com>
Tested-by: Tomas Papan <tomas.papan@gmail.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
CC: stable@vger.kernel.org
Signed-off-by: Gleb Natapov <gleb@redhat.com>
From: James Cosin <jkosin@intcomgrp.com>
fixes the number of digits to 6 after the decimal point to regain the
significant 0s in the frequency after the decimal point.
Signed-off-by: Steven Miao <realmz6@gmail.com>
The bootloader configures the pins, but has pull bits
set without pull enable bits. While this is harmless,
and won't do anything, it seems to cause confusion at
least for me every time looking at the pin configuration.
Fix it for DT based boot.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPMC data node to AM33XX device tree file.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit d16fb25 (ARM: dts: OMAP4460: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP4460 OPP data in
arch/arm/mach-omap2/opp4xxx_data.c
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
commit 3027e26 (ARM: dts: OMAP36xx: Add CPU OPP table)
introduced wrong OPP voltages per OPP by mistake. Sync the OPP
tables with existing OMAP36xx OPP data in
arch/arm/mach-omap2/opp3xxx_data.c
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Boards supported upstream all use TWL6040 as audio codec, enable the common
ASoC machine driver by default for them.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for chip id detection of AM335x PG2.1 Silicon.
Currently omap3xxx_check_revision() detects PG1.0 and PG2.0 only,
this patch extends it by adding PG2.1 Si support.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch adds support for fan control button on Ideapad Z580. This is
the same button as on Z570, but it raises different bit in
VPCCMD_R_SPECIAL_BUTTONS. Also add message to dmesg when unknown button
press detected, it will help adding support for new special buttons.
Signed-off-by: Maxim Mikityanskiy <maxtram95@gmail.com>
Tested-by: Ivan Vojtko <nekroman.sk@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
pvpanic device is a qemu simulated device through which guest panic
event is sent to host.
Signed-off-by: Hu Tao <hutao@cn.fujitsu.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
BugLink: http://bugs.launchpad.net/bugs/1172151
Need to set wapf to 4 for ASUSTeK COMPUTER INC. X75A, so that
user can toggle wifi function through function key correctly.
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Used PTR_RET function instead of IS_ERR and PTR_ERR.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
SVS151290S series uses handle 0x0163 for keyboard backlight and 0x015B for the graphics switch.
Signed-off-by: Arthur Wirski <awirski@gmail.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
New HP laptops start generating new events, and hp-wmi prints unknown
event_ids for them. This patch also removes these messages
Signed-off-by: Alex Hung <alex.hung@canonical.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
If krealloc() returns NULL, it *doesn't* free the original. So any code
of the form 'foo = krealloc(foo, …);' is almost certainly a bug.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
The error in lis3lv02_poweron() is harmless in the resume path, so
we should ignore it. It is inline with the other usages of lis3lv02_poweron()
and matches the 3.0 code for this routine. This patch is in suse git and
might have missed making it into the mainline.
opensuse - commit id: 66ccdac87c322cf7af12bddba8c805af640b1cff
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Shuah Khan <shuah.khan@hp.com>
CC: stable@vger.kernel.org 3.8, 3.4, 3.5, 3.2
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
There is a new DELL WMI spec. with new WMI event format.
I'm working on the AIO machines, but I think the new format will apply to
all the Dell's machines, not only for AIO, which will be released later
this year.
The new format of the WMI buffer is shown as below
word 0 - the number of words following in the WMI buffer(not including
this word.
word 1 - the event type
0x0000 - A hot key is pressed or an event occurred
0x000F - A sequence of hot keys are pressed
word 2 and on - the event data
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Add the missing iounmap() before return from omap1_system_dma_init()
in the error handling case.
Also removed platform_device_del() on add resources error case which
cause dup device delete.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If DEBUG_LL and earlyprintk are enabled, and omap-serial.c is compiled
as a module, the kernel boot hangs early as the clocks for serial port
are cut while earlyprintk still uses the port.
The problem is a race between the late_initcall for omap_device (which
idles devices that have no drivers) and the late_initcall in
kernel/printk.c which turns off the earlyconsole. Any printks
that happen between this omap_device late initcall and the earlyconsole
late initcall will crash when accessing the UART.
The fix is to ensure the omap_device initcall happens after the
earlyconsole initcall.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 9fdca9df (spi: omap2-mcspi: convert to module_platform_driver)
broke the SPI display/panel driver probe on RX-51/N900. The exact cause is
not fully understood, but it seems to be related to the probe order. SPI
communication to the panel driver (spi1.2) fails unless the touchscreen
(spi1.0) has been probed/initialized before. When the omap2-mcspi driver
was converted to a platform driver, it resulted in that the devices are
probed immediately after the board registers them in the order they are
listed in the board file.
Fix the issue by moving the touchscreen before the panel in the SPI
device list.
The patch fixes the following failure:
[ 1.260955] acx565akm spi1.2: invalid display ID
[ 1.265899] panel-acx565akm display0: acx_panel_probe panel detect error
[ 1.273071] omapdss CORE error: driver probe failed: -19
Tested-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Joni Lapilainen <joni.lapilainen@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
