Now that our state comparison functions are pretty complete, we should
enable fastset by default when a modeset can be avoided. Even if we're
not completely certain about the inherited state, we can be certain
after the first modeset that our sw state matches the hw state.
There is one testcase explicitly testing fastset,
kms_panel_fitting.atomic-fastset but other testcases do so indirectly
because most tests don't clean up the display during exit, or otherwise
indirectly preserve mode by doing igt_display_reset or inheriting during
init.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
[mlankhorst: Use DRM_DEBUG_KMS. (j4ni)]
Link: https://patchwork.freedesktop.org/patch/msgid/20190108160842.13396-3-maarten.lankhorst@linux.intel.com
On lynxpoint the bios sometimes sets up the backlight using the CPU
display, but the driver expects using the PWM PCH override register.
Read the value from the CPU register, then convert it to the other
units by converting from the old duty cycle, to freq, to the new units.
This value is then programmed in the override register, after which
we set the override and disable the CPU display control. This allows
us to switch the source without flickering, and make the backlight
controls work in the driver.
Changes since v1:
- Read BLC_PWM_CPU_CTL2 to cpu_ctl2.
- Clean up cpu_mode if slightly.
- Always disable BLM_PWM_ENABLE in cpu_ctl2.
Changes since v2:
- Simplify cpu_mode handling (Jani)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108225
Cc: Basil Eric Rabi <ericbasil.rabi@gmail.com>
Cc: Hans de Goede <jwrdegoede@fedoraproject.org>
Cc: Tolga Cakir <cevelnet@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Tolga Cakir <cevelnet@gmail.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108160842.13396-2-maarten.lankhorst@linux.intel.com
Restore our saved values for backlight. This way even with fastset on
S4 resume we will correctly restore the backlight to the active values.
Changes since v1:
- Call enable_backlight() when backlight.level is set. On suspend
backlight.enabled is always cleared, this makes it not a good
indicator. Also check for crtc->state->active.
Changes since v2:
- Use the new update_pipe() callback to run this on resume as well.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Tolga Cakir <cevelnet@gmail.com>
Cc: Basil Eric Rabi <ericbasil.rabi@gmail.com>
Cc: Hans de Goede <jwrdegoede@fedoraproject.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190108160842.13396-1-maarten.lankhorst@linux.intel.com
The VBT int_crt_support can't be trusted on earlier platforms, and is
always set to true in intel_bios.c for pre-DDI and pre-VLV platforms. We
can simplify the output setup by unconditionally calling
intel_crt_init() for these platforms.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190122082307.4003-7-jani.nikula@intel.com
With most platforms not having TV support, only call intel_tv_init() on
platforms that might actually have TV, specifically gens 3 and 4.
This puts intel_tv_init() more in line with the rest of the outputs, and
makes it slightly easier for the uninitiated to figure out which
platforms actually have what.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190122082307.4003-4-jani.nikula@intel.com
Now that intel_lvds_init() is only called for platforms that might have
LVDS, move the remaining checks to intel_setup_outputs(), again similar
to other outputs, and remove the overlapping checks.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190122082307.4003-3-jani.nikula@intel.com
With new platforms not having LVDS support, only call intel_lvds_init()
on platforms that might actually have LVDS. Move the comment about eDP
init to the PCH block where it's relevant.
This puts intel_lvds_init() more in line with the rest of the outputs,
and makes it slightly easier for the uninitiated to figure out which
platforms actually have what.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190122082307.4003-2-jani.nikula@intel.com
With new platforms not having CRT support and most conditions in
intel_crt_present() being specific to DDI, split out the CRT
initialization to platform specific blocks in the if ladder. Add new
Pineview block for this.
This puts intel_crt_init() more in line with the rest of the outputs,
and makes it slightly easier for the uninitiated to figure out which
platforms actually have what.
v2: keep gen >= 9 check in intel_ddi_crt_present() (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190122082307.4003-1-jani.nikula@intel.com
We currently program userspace-provided gamma and degamma LUT's into our
hardware without really checking to see whether they satisfy our
hardware's rules. We should try to catch tables that are invalid for
our hardware early and reject the atomic transaction.
All of our platforms that accept a degamma LUT expect that the entries
in the LUT are always flat or increasing, never decreasing. Also, our
GLK and ICL platforms only accept degamma tables with r=g=b entries; so
we should also add the relevant checks for that in anticipation of
degamma support landing for those platforms.
v2:
- Use new API (single check function with bitmask of tests to apply)
- Call helper for our gamma table as well (with no additional tests
specified) so that the table size will be validated.
v3:
- Don't call on the gamma table since the LUT size is already tested at
property blob upload and we don't have any additional hardware
constraints for that LUT.
v4:
- Apply equal color channel check on gen10 as well; the bspec has some
strange tagging for CNL platforms, but this appears to apply there as
well. (Ville)
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181218175158.5739-1-matthew.d.roper@intel.com
Some hardware may place additional restrictions on the gamma/degamma
curves described by our LUT properties. E.g., that a gamma curve never
decreases or that the red/green/blue channels of a LUT's entries must be
equal. Let's add a helper function that drivers can use to test that a
userspace-provided LUT is valid and doesn't violate hardware
requirements.
v2:
- Combine into a single helper that just takes a bitmask of the tests
to apply. (Brian Starkey)
- Add additional check (always performed) that LUT property blob size
is always a multiple of the LUT entry size. (stolen from ARM driver)
v3:
- Drop the LUT size check again since
drm_atomic_replace_property_blob_from_id() already covers this for
us. (Alexandru Gheorghe)
v4:
- Use an enum to describe possible test values rather than #define's;
this is cleaner to provide kerneldoc for. (Daniel Vetter)
- s/DRM_COLOR_LUT_INCREASING/DRM_COLOR_LUT_NON_DECREASING/. (Ville)
Cc: Uma Shankar <uma.shankar@intel.com>
Cc: Swati Sharma <swati2.sharma@intel.com>
Cc: Brian Starkey <Brian.Starkey@arm.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Brian Starkey <brian.starkey@arm.com>
Reviewed-by: Alexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181217224415.12848-1-matthew.d.roper@intel.com
Record the priority boost we giving to the preempted client or else we
may end up in a situation where the priority queue no longer matches the
request priority order and so we can end up in an infinite loop of
preempting the same pair of requests.
Fixes: e9eaf82d97 ("drm/i915: Priority boost for waiting clients")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190123135155.21562-1-chris@chris-wilson.co.uk
When reading GEN11_GT_INTR_DWx closely after enabling the interrupts
in gen11_irq_postinstall, the returned value is garbage. This can
cause other parts of the setup code (e.g. gen11_reset_one_iir) to
think that there are interrupts to be cleared when there are none.
The garbage value is only seen on the first read done after the enable,
so this looks like a posting issue. Adding a posting read after enabling
the interrupts does indeed fix the problem.
Note that the posting read has been purposely added outside of
gen11_master_intr_enable since the issue has only been observed when the
full interrupt setup is performed.
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190123023227.8117-1-daniele.ceraolospurio@intel.com
Mixed C99 and kernel types use is getting ugly. Prefer kernel types.
sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
v2: rebase
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118120125.15484-1-jani.nikula@intel.com
Mixed C99 and kernel types use is getting ugly. Prefer kernel types.
sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
Acked-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The value of this registers will be used to test if PSR2 is doing
selective update and if the number of blocks match with the expected.
v2:
- Using new macros
- Changed the string output
v3:
- reading PSR2_SU_STATUS registers together(Dhinakaran)
- printing SU blocks of frames with 0 updates(Dhinakaran)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190117205548.28378-4-jose.souza@intel.com
This register contains how many blocks was sent in the past selective
updates.
Those registers are not kept set all the times but polling it after flip
can show the values corresponding to the last 8 frames.
v2: Improved macros(Dhinakaran)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190117205548.28378-3-jose.souza@intel.com
The old debugfs fields was not following a naming partern and it was
a bit confusing.
So it went from:
~$ sudo more /sys/kernel/debug/dri/0/i915_edp_psr_status
Sink_Support: yes
PSR mode: PSR1
Enabled: yes
Busy frontbuffer bits: 0x000
Main link in standby mode: no
HW Enabled & Active bit: yes
Source PSR status: 0x24050006 [SRDONACK]
To:
~$ sudo more /sys/kernel/debug/dri/0/i915_edp_psr_status
Sink support: yes [0x03]
PSR mode: PSR1 enabled
Source PSR ctl: enabled [0x81f00e26]
Source PSR status: IDLE [0x04010006]
Busy frontbuffer bits: 0x00000000
The 'Main link in standby mode' was removed as it is not useful but
if needed by someone the information is still in the register value
of 'Source PSR ctl' inside of the brackets, PSR mode and Enabled was
squashed into PSR mode, some renames and reorders and we have this
cleaner version. This will also make easy to parse debugfs for IGT
tests.
v2: Printing sink PSR version with only 2 hex digits as it is a byte
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Suggested-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190117205548.28378-2-jose.souza@intel.com
For now PSR2 is still disabled by default for all platforms but is
our intention to let debugfs to enable it for debug and tests
proporses, so intel_psr2_enabled() that is also used by debugfs to
decide if PSR2 is going to be enabled needs to take in consideration
the debug field.
v2: Using the switch/case that intel_psr2_enabled() already had to
handle this(DK)
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190117205548.28378-1-jose.souza@intel.com
Prior to adding a third instance of intel_context_init() and extending
the information stored therewithin, refactor out the common assignments.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190121222117.23305-8-chris@chris-wilson.co.uk
Before adding yet another copy of struct live_test and its handler,
refactor the existing code into a common framework for live selftests.
For many live selftests, we want to know if the GPU hung or otherwise
misbehaved during the execution of the test (beyond any infraction in
the behaviour under test), live_test provides this by comparing the
GPU state before and after, alerting if it unexpectedly changed (e.g.
the reset counter changed). It also ensures that the GPU is idle before
and after the test, so that residual code running on the GPU is flushed
before testing.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190121222117.23305-5-chris@chris-wilson.co.uk
Some tests (e.g. igt_vma_pin1) presume that we have a completely clean
GGTT so that it can probe boundaries without fear that something is
already allocated there. However, the mock device is starting to get
complicated and following similar rules to the live device, i.e. we
can't guarantee that i915->ggtt remains clean, so create a temporary
address_space equivalent to the mock ggtt for the purpose.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190121222117.23305-7-chris@chris-wilson.co.uk
During review of commit 71fc448c1a ("drm/i915/selftests: Make evict
tolerant of foreign objects"), Matthew mentioned it would be better if
we explicitly tracked the objects we created. We have an obj->st_link
hook for this purpose, so add the corresponding list of objects and
reduce our loops to only consider our own list.
References: 71fc448c1a ("drm/i915/selftests: Make evict tolerant of foreign objects")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190121222117.23305-6-chris@chris-wilson.co.uk
The display engine has 2 dithering enable bits which both need to be set
for dithering to happen, 1 in the PIPECONF register which is taken care of
by i9xx_set_pipeconf() and a second bit at the encoder level.
The dsi code was not setting the encoder level dithering enable bit causing
dithering to be disabled, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181201113148.23184-2-hdegoede@redhat.com
There are 3 problems with the dsi code's pipe_bpp handling for 6 bpc
pixel-formats which this commit addresses:
1) It assumes that the pipe_bpp is the same as the bpp going over the dsi
lanes. This assumption is not valid for MIPI_DSI_FMT_RGB666, where pipe_bpp
should be 18 so that we do proper dithering but we actually send 24 bpp
over the dsi lanes (MIPI_DSI_FMT_RGB666_PACKED sends 18 bpp).
This assumption is enforced by an assert in *_dsi_get_pclk(). This assert
triggers on the initial hw-state readback on BYT/CHT devices which use
MIPI_DSI_FMT_RGB666, such as the Prowise PT301 tablet. PIPECONF is set to
6BPC / 18 bpp by the GOP, while mipi_dsi_pixel_format_to_bpp() returns 24.
This commits switches the calculations in *_dsi_get_pclk() to use the bpp
from mipi_dsi_pixel_format_to_bpp(intel_dsi->pixel_format) which
returns the bpp going over the mipi lanes and drops the assert.
2) On BXT bxt_dsi_get_pipe_config() wrongly overrides the pipe_bpp which
i9xx_get_pipe_config() reads from PIPECONF with the return value from
mipi_dsi_pixel_format_to_bpp(). This avoids the assert from 1. but is wrong
since the pipe is actually running at the value configured in PIPECONF.
This commit drops the override of pipe_bpp from bxt_dsi_get_pipe_config().
3) The dsi encoder's compute_config() never assigns a value to pipe_bpp,
unlike most other encoders. Falling back on compute_baseline_pipe_bpp()
which always picks 24. 24 is only correct for MIPI_DSI_FMT_RGB88 for the
others we should use 18 bpp so that we correctly do 6bpc color dithering.
This commit adds code to intel_dsi_compute_config() to properly set
pipe_bpp based on intel_dsi->pixel_format.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181201113148.23184-1-hdegoede@redhat.com
We are not allowed to assign rq->global_seqno=0 as it has a special
meaning of "inactive" (not executing on HW).
Fixes: 6faf5916e6 ("drm/i915: Remove HW semaphores for gen7 inter-engine synchronisation")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190119143024.26971-1-chris@chris-wilson.co.uk
Mixed C99 and kernel types use is getting ugly. Prefer kernel types.
sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
Minor checkpatch fixes sprinkled on top of the changed lines.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118120125.15484-8-jani.nikula@intel.com
Mixed C99 and kernel types use is getting ugly. Prefer kernel types.
sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118120125.15484-7-jani.nikula@intel.com
Mixed C99 and kernel types use is getting ugly. Prefer kernel types.
sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118120125.15484-6-jani.nikula@intel.com
Mixed C99 and kernel types use is getting ugly. Prefer kernel types.
sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
Minor checkpatch/whitepace fixes sprinkled on top of the changed lines.
v2: more whitespace fixes (Ville, José)
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118120125.15484-5-jani.nikula@intel.com
Mixed C99 and kernel types use is getting ugly. Prefer kernel types.
sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118120125.15484-4-jani.nikula@intel.com
Mixed C99 and kernel types use is getting ugly. Prefer kernel types.
sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
Minor checkpatch fixes sprinkled on top of the changed lines.
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118120125.15484-3-jani.nikula@intel.com
Mixed C99 and kernel types use is getting ugly. Prefer kernel types.
sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118120125.15484-2-jani.nikula@intel.com
The evict selftests presumed that all objects in use had been allocated
by itself. This is a dubious claim and so instead of asserting complete
control over the object lists, take (temporary) ownership of them
instead.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118113632.7056-1-chris@chris-wilson.co.uk
Since commit d4ccceb055 ("drm/i915/icl: Ringbuffer interrupt handling")
we have required a mechanism to avoid touching the interrupt hardware
for breadcrumbs, superseding our mock interface for selftests.
The residual problem (ideas welcome) is in probing the mock ring
registers for ring_is_idle. Hmm, maybe we should just install
mock handlers for i915->uncore.mmio__write and friends? Only problem
being is that we would to truly mock some expected reads. :(
References: d4ccceb055 ("drm/i915/icl: Ringbuffer interrupt handling")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190118112225.13780-1-chris@chris-wilson.co.uk
Since we have the ppgtt we want to test, we can ask it directly if it is
suitable for the hugepage test we intend to undertake.
v2: Not everyone has full-ppgtt
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190117230512.4789-1-chris@chris-wilson.co.uk
The motivation for introducing the check that we only enable breadcrumb
irqs if the device's irq was installed was once upon a time we waited
during suspend after disabling interrupts (which was quite slow until
the bug was discovered). Since then we have the notion of pinning the
breadcrumb irq, broadening it from the sole purpose of user interrupt
notification and waiting, and more importantly decoupling it from a very
defined time period during which enabling the irq was expected. So stop
insisting the irq is installed before we setup our IMR masks, if the IER
isn't yet enabled, nothing will happen and we will timeout instead,
revealing the lack of irq in the hang debug messages.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190117233126.30165-1-chris@chris-wilson.co.uk
UAPI Changes:
- New fourcc identifier for ARM Framebuffer Compression v1.3
Cross-subsystem Changes:
Core Changes:
- Reorganisation of drm_device and drm_framebuffer headers
- Cleanup of the drmP inclusion
- Fix leaks in the fb-helpers
- Allow for depth different from bpp in fb-helper fbdev emulation
- Remove drm_mode_object from drm_display_mode
Driver Changes:
- Add reflection properties to rockchip
- a bunch of fixes for virtio
- a bunch of fixes for dp_mst and drivers using it, and introduction of a
new refcounting scheme
- Convertion of bochs to atomic and generic fbdev emulation
- Allow meson to remove the firmware framebuffers
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXD+OHgAKCRDj7w1vZxhR
xe3IAP4s59sFVMZseVJpwSe41OJ1ipD/cyIbtXU94X6nFd6zCAD+Jm4q+XIIS+uv
7ElmJ2BD7rwicqSViWNG8tteHYfjrAU=
=XPsb
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-01-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for 5.1:
UAPI Changes:
- New fourcc identifier for ARM Framebuffer Compression v1.3
Cross-subsystem Changes:
Core Changes:
- Reorganisation of drm_device and drm_framebuffer headers
- Cleanup of the drmP inclusion
- Fix leaks in the fb-helpers
- Allow for depth different from bpp in fb-helper fbdev emulation
- Remove drm_mode_object from drm_display_mode
Driver Changes:
- Add reflection properties to rockchip
- a bunch of fixes for virtio
- a bunch of fixes for dp_mst and drivers using it, and introduction of a
new refcounting scheme
- Convertion of bochs to atomic and generic fbdev emulation
- Allow meson to remove the firmware framebuffers
[airlied: patch rcar-du to add drm_modes.h]
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190116200428.u2n4jbk4mzza7n6e@flea
Let static analyzers (smatch) know that we are not going to wander off
the end of the array by providing a tight upper bound:
drivers/gpu/drm/i915/intel_display.c:9532 hsw_get_transcoder_state() error: buffer overflow 'dev_priv->__info.trans_offsets' 6 <= 31
References: 0716931a82 ("drm/i915/icl: fix transcoder state readout")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190116155421.7660-1-chris@chris-wilson.co.uk
Mixed C99 and kernel types use is getting ugly. Prefer kernel types.
sed -i 's/\buint\(8\|16\|32\|64\)_t\b/u\1/g'
Minor checkpatch fixes sprinkled on top of the changed lines.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/14ed72e7f04c9340a057855c5950b54811f8a477.1547629303.git.jani.nikula@intel.com
Make i915_gem_set_wedged() and i915_gem_unset_wedged() behaviour more
consistent if called concurrently, and only do the wedging and reporting
once, curtailing any possible race where we start unwedging in the middle
of a wedge.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114210408.4561-2-chris@chris-wilson.co.uk
Something that I completely missed when implementing the new MST VCPI
atomic helpers is that with those helpers, there's technically a chance
of us having to grab additional modeset locks in ->compute_config() and
furthermore, that means we have the potential to hit a normal modeset
deadlock. However, because ->compute_config() only returns a bool this
means we can't return -EDEADLK when we need to drop locks and try again
which means we end up just failing the atomic check permanently. Whoops.
So, fix this by modifying ->compute_config() to pass down an actual
error code instead of a bool so that the atomic check can be restarted
on modeset deadlocks.
Thanks to Ville Syrjälä for pointing this out!
Changes since v1:
* Add some newlines
* Return only -EINVAL from hsw_crt_compute_config()
* Propogate return code from intel_dp_compute_dsc_params()
* Change all of the intel_dp_compute_link_config*() variants
* Don't miss if (hdmi_port_clock_valid()) branch in
intel_hdmi_compute_config()
[Cherry-picked from drm-misc-next to drm-intel-next-queued to fix
linux-next & drm-tip conflict, while waiting for proper propagation of
the DP MST series that this commit fixes. In hindsight, a topic branch
might have been a better approach for it.]
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: eceae14724 ("drm/dp_mst: Start tracking per-port VCPI allocations")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109320
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190115200800.3121-1-lyude@redhat.com
(cherry picked from commit 96550555a7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
mutex_lock_killable() returns -EINTR on failure, not the anticipate bool
return like trylock. (Oh no, not again.)
Fixes: 484d9a844d ("drm/i915/userptr: Avoid struct_mutex recursion for mmu_invalidate_range_start")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190115221118.13304-1-chris@chris-wilson.co.uk
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Something that I completely missed when implementing the new MST VCPI
atomic helpers is that with those helpers, there's technically a chance
of us having to grab additional modeset locks in ->compute_config() and
furthermore, that means we have the potential to hit a normal modeset
deadlock. However, because ->compute_config() only returns a bool this
means we can't return -EDEADLK when we need to drop locks and try again
which means we end up just failing the atomic check permanently. Whoops.
So, fix this by modifying ->compute_config() to pass down an actual
error code instead of a bool so that the atomic check can be restarted
on modeset deadlocks.
Thanks to Ville Syrjälä for pointing this out!
Changes since v1:
* Add some newlines
* Return only -EINVAL from hsw_crt_compute_config()
* Propogate return code from intel_dp_compute_dsc_params()
* Change all of the intel_dp_compute_link_config*() variants
* Don't miss if (hdmi_port_clock_valid()) branch in
intel_hdmi_compute_config()
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: eceae14724 ("drm/dp_mst: Start tracking per-port VCPI allocations")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=109320
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190115200800.3121-1-lyude@redhat.com
Since commit 93065ac753 ("mm, oom: distinguish blockable mode for mmu
notifiers") we have been able to report failure from
mmu_invalidate_range_start which allows us to use a trylock on the
struct_mutex to avoid potential recursion and report -EBUSY instead.
Furthermore, this allows us to pull the work into the main callback and
avoid the sleight-of-hand in using a workqueue to avoid lockdep.
However, not all paths to mmu_invalidate_range_start are prepared to
handle failure, so instead of reporting the recursion, deal with it by
propagating the failure upwards, who can decide themselves to handle it
or report it.
v2: Mark up the recursive lock behaviour and comment on the various weak
points.
v3: Follow commit 3824e41975 ("drm/i915: Use mutex_lock_killable() from
inside the shrinker") and also use mutex_lock_killable().
v3.1: No leak on EINTR.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108375
References: 93065ac753 ("mm, oom: distinguish blockable mode for mmu notifiers")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190115124442.3500-1-chris@chris-wilson.co.uk
Registering an output for a non-existent port (on a given SKU) can lead
to problems when trying to use the port, for instance timeouts during
power well enabling. Since there are no strap bits for port detection we
have to rely on VBT for this, so do that here.
There are no known SKUs where any of the A-E ports are non-existent, so
to reduce the likelihood of breakage due to incorrect VBT information,
do this detection only for port F (which is known to be missing on some
ICL SKUs).
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108915
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181220132604.25222-2-imre.deak@intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
We have already a function to detect DDI ports using VBT, so instead of
opencoding the DDI specific version of this, move the opencoded part to
the existing helper.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181220132604.25222-1-imre.deak@intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
As we may frequently mark the device as wedged to flush requests off it
during the normal course of events, quite often we have a large state
dump that is of no interest. Don't bother dumping it all if the engines
are all idle.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190115122057.1677-1-chris@chris-wilson.co.uk
There is a plan to build the kernel with -Wimplicit-fallthrough and
these places in the code produced warnings (W=1). Fix them up.
This commit remove the following warnings:
include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/asm-generic/bug.h:134:2: note: in expansion of macro 'unlikely'
drivers/gpu/drm/drm_dp_helper.c:155:3: note: in expansion of macro 'WARN'
include/linux/compiler.h:77:22: warning: this statement may fall through [-Wimplicit-fallthrough=]
include/asm-generic/bug.h:134:2: note: in expansion of macro 'unlikely'
drivers/gpu/drm/drm_dp_helper.c:173:3: note: in expansion of macro 'WARN'
drivers/gpu/drm/drm_dp_helper.c:547:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114202748.15584-1-malat@debian.org
CNL macros for register groups CNL_PORT_TX_DW2_* / CNL_PORT_TX_DW5_* are
configured incorrectly wrt definition of _CNL_PORT_TX_DW_GRP.
v2: Jani suggested to keep the macros organized semantically i.e., by
function, secondarily by port/pipe/transcoder.->(dw, port)
Fixes: 4e53840fdf ("drm/i915/icl: Introduce new macros to get combophy registers")
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190110230844.9213-1-aditya.swarup@intel.com
On Braswell, under heavy stress, if we update the GGTT while
simultaneously accessing another region inside the GTT, we are returned
the wrong values. To prevent this we stop the machine to update the GGTT
entries so that no memory traffic can occur at the same time.
This was first spotted in
commit 5bab6f60cb
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Oct 23 18:43:32 2015 +0100
drm/i915: Serialise updates to GGTT with access through GGTT on Braswell
but removed again in forlorn hope with
commit 4509276ee8
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Mon Feb 20 12:47:18 2017 +0000
drm/i915: Remove Braswell GGTT update w/a
However, gem_concurrent_blit is once again only stable with the patch
applied and CI is detecting the odd failure in forked gem_mmap_gtt tests
(which smell like the same issue). Fwiw, a wide variety of CPU memory
barriers (around GGTT flushing, fence updates, PTE updates) and GPU
flushes/invalidates (between requests, after PTE updates) were tried as
part of the investigation to find an alternate cause, nothing comes
close to serialised GGTT updates.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105591
Testcase: igt/gem_concurrent_blit
Testcase: igt/gem_mmap_gtt/*forked*
References: 5bab6f60cb ("drm/i915: Serialise updates to GGTT with access through GGTT on Braswell")
References: 4509276ee8 ("drm/i915: Remove Braswell GGTT update w/a")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114211729.30352-1-chris@chris-wilson.co.uk
We have two classes of VM, global GTT and per-process GTT. In order to
allow ourselves the freedom to mix both along call chains, distinguish
the two classes with regards to their mutex and lockdep maps.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114215956.32266-1-chris@chris-wilson.co.uk
On i965gm we need to adjust max_vblank_count dynamically
depending on whether the TV encoder is used or not. To
that end add a per-crtc max_vblank_count that takes
precedence over its device wide counterpart. The driver
can now call drm_crtc_set_max_vblank_count() to configure
the per-crtc value before calling drm_vblank_on().
Also looks like there was some discussion about exynos needing
similar treatment.
v2: Drop the extra max_vblank_count!=0 check for the
WARN(last!=current), will take care of it in i915 code (Daniel)
WARN_ON(!inmodeset) (Daniel)
WARN_ON(dev->max_vblank_count)
Pimp up the docs (Daniel)
Cc: stable@vger.kernel.org
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181127182004.28885-1-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently Ironlake operates under the assumption that rpm awake (and its
error checking is disabled). As such, we have missed a few places where we
access registers without taking the rpm wakeref and thus trigger
warnings. intel_ips being one culprit.
As this involved adding a potentially sleeping rpm_get, we have to
rearrange the spinlocks slightly and so switch to acquiring a device-ref
under the spinlock rather than hold the spinlock for the whole
operation. To be consistent, we make the change in pattern common to the
intel_ips interface even though this adds a few more atomic operations
than necessary in a few cases.
v2: Sagar noted the mb around setting mch_dev were overkill as we only
need ordering there, and that i915_emon_status was still using
struct_mutex for no reason, but lacked rpm.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-21-chris@chris-wilson.co.uk
As the GT_IRQ power domain implies a wakeref, we can use it inplace of
our existing redundant rpm grab.
v2: Drop papering over forgetting to take the runtime wakeref in
selftests
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-20-chris@chris-wilson.co.uk
As we only release each power well once, we assume that each transcoder
maps to a different domain. Complain if this is not so.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-19-chris@chris-wilson.co.uk
Track where and when we acquire and release the power well for pps
access along the dp aux link, with a view to detecting if we leak any
wakerefs.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-18-chris@chris-wilson.co.uk
On module load and unload, we grab the POWER_DOMAIN_INIT powerwells and
transfer them to the runtime-pm code. We can use our wakeref tracking to
verify that the wakeref is indeed passed from init to enable, and
disable to fini; and across suspend.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-17-chris@chris-wilson.co.uk
The majority of runtime-pm operations are bounded and scoped within a
function; these are easy to verify that the wakeref are handled
correctly. We can employ the compiler to help us, and reduce the number
of wakerefs tracked when debugging, by passing around cookies provided
by the various rpm_get functions to their rpm_put counterpart. This
makes the pairing explicit, and given the required wakeref cookie the
compiler can verify that we pass an initialised value to the rpm_put
(quite handy for double checking error paths).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-16-chris@chris-wilson.co.uk
Frequently, we use intel_runtime_pm_get/_put around a small block.
Formalise that usage by providing a macro to define such a block with an
automatic closure to scope the intel_runtime_pm wakeref to that block,
i.e. macro abuse smelling of python.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-15-chris@chris-wilson.co.uk
Track the temporary wakerefs used within the selftests so that leaks are
clear.
v2: Add a couple of coarse annotations for mock selftests as we now
loudly warn about the errors.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-14-chris@chris-wilson.co.uk
Keep track of the temporary rpm wakeref used for panel backlight access,
so that we can cancel it immediately upon release and so more clearly
identify leaks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-13-chris@chris-wilson.co.uk
Keep track of the temporary rpm wakeref inside hotplug detection, so
that we can cancel it immediately upon release and so clearly identify
leaks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-12-chris@chris-wilson.co.uk
Keep track of the rpm wakeref used for framebuffer access so that we can
cancel upon release and so more clearly identify leaks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-11-chris@chris-wilson.co.uk
Keep track of the temporary rpm wakerefs used for user access to the
device, so that we can cancel them upon release and clearly identify any
leaks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-10-chris@chris-wilson.co.uk
Keep track of our acquired wakeref for interacting with the guc, so that
we can cancel it upon release and so clearly identify leaks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-9-chris@chris-wilson.co.uk
Track the wakeref used for temporary access to the device, and discard
it upon release so that leaks can be identified.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-8-chris@chris-wilson.co.uk
As debugfs has a simple pattern of taking a rpm wakeref around the user
access, we can track the local reference and drop it as soon as
possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-6-chris@chris-wilson.co.uk
As sysfs has a simple pattern of taking a rpm wakeref around the user
access, we can track the local reference and drop it as soon as
possible.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-5-chris@chris-wilson.co.uk
Keep hold of the local wakeref used in error handling, to cancel
the tracking upon release so that leaks can be identified.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-4-chris@chris-wilson.co.uk
Record the wakeref used for keeping the device awake as the GPU is
executing requests and be sure to cancel the tracking upon parking.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-3-chris@chris-wilson.co.uk
The majority of runtime-pm operations are bounded and scoped within a
function; these are easy to verify that the wakeref are handled
correctly. We can employ the compiler to help us, and reduce the number
of wakerefs tracked when debugging, by passing around cookies provided
by the various rpm_get functions to their rpm_put counterpart. This
makes the pairing explicit, and given the required wakeref cookie the
compiler can verify that we pass an initialised value to the rpm_put
(quite handy for double checking error paths).
For regular builds, the compiler should be able to eliminate the unused
local variables and the program growth should be minimal. Fwiw, it came
out as a net improvement as gcc was able to refactor rpm_get and
rpm_get_if_in_use together,
v2: Just s/rpm_put/rpm_put_unchecked/ everywhere, leaving the manual
mark up for smaller more targeted patches.
v3: Mention the cookie in Returns
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190114142129.24398-2-chris@chris-wilson.co.uk
