In preparation for being able to decompress into a buffer starting at a
different address than startup_32, save the calculated output address
instead of recalculating it later.
We now keep track of three addresses:
%edx: startup_32 as we were loaded by bootloader
%ebx: new location of compressed kernel
%ebp: start of decompression buffer
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200303221205.4048668-2-nivedita@alum.mit.edu
Link: https://lore.kernel.org/r/20200308080859.21568-16-ardb@kernel.org
The load address is compared with LOAD_PHYSICAL_ADDR using a signed
comparison currently (using jge instruction).
When loading a 64-bit kernel using the new efi32_pe_entry() point added by:
97aa276579 ("efi/x86: Add true mixed mode entry point into .compat section")
using Qemu with -m 3072, the firmware actually loads us above 2Gb,
resulting in a very early crash.
Use the JAE instruction to perform a unsigned comparison instead, as physical
addresses should be considered unsigned.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200301230436.2246909-6-nivedita@alum.mit.edu
Link: https://lore.kernel.org/r/20200308080859.21568-14-ardb@kernel.org
code32_start is meant for 16-bit real-mode bootloaders to inform the
kernel where the 32-bit protected mode code starts. Nothing in the
protected mode kernel except the EFI stub uses it.
efi_main() currently returns boot_params, with code32_start set inside it
to tell efi_stub_entry() where startup_32 is located. Since it was invoked
by efi_stub_entry() in the first place, boot_params is already known.
Return the address of startup_32 instead.
This will allow a 64-bit kernel to live above 4Gb, for example, and it's
cleaner as well.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200301230436.2246909-5-nivedita@alum.mit.edu
Link: https://lore.kernel.org/r/20200308080859.21568-13-ardb@kernel.org
The following commit:
ef5a7b5eb1 ("efi/x86: Remove GDT setup from efi_main")
introduced GDT setup into the 32-bit kernel's startup_32, and reloads
the GDTR after relocating the kernel for paranoia's sake.
A followup commit:
32d009137a ("x86/boot: Reload GDTR after copying to the end of the buffer")
introduced a similar GDTR reload in the 64-bit kernel as well.
The GDTR is adjusted by (init_size-_end), however this may not be the
correct offset to apply if the kernel was loaded at a misaligned address
or below LOAD_PHYSICAL_ADDR, as in that case the decompression buffer
has an additional offset from the original load address.
This should never happen for a conformant bootloader, but we're being
paranoid anyway, so just store the new GDT address in there instead of
adding any offsets, which is simpler as well.
Fixes: ef5a7b5eb1 ("efi/x86: Remove GDT setup from efi_main")
Fixes: 32d009137a ("x86/boot: Reload GDTR after copying to the end of the buffer")
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86@kernel.org
Link: https://lore.kernel.org/r/20200226230031.3011645-2-nivedita@alum.mit.edu
This time, the set of changes for the EFI subsystem is much larger than
usual. The main reasons are:
- Get things cleaned up before EFI support for RISC-V arrives, which will
increase the size of the validation matrix, and therefore the threshold to
making drastic changes,
- After years of defunct maintainership, the GRUB project has finally started
to consider changes from the distros regarding UEFI boot, some of which are
highly specific to the way x86 does UEFI secure boot and measured boot,
based on knowledge of both shim internals and the layout of bootparams and
the x86 setup header. Having this maintenance burden on other architectures
(which don't need shim in the first place) is hard to justify, so instead,
we are introducing a generic Linux/UEFI boot protocol.
Summary of changes:
- Boot time GDT handling changes (Arvind)
- Simplify handling of EFI properties table on arm64
- Generic EFI stub cleanups, to improve command line handling, file I/O,
memory allocation, etc.
- Introduce a generic initrd loading method based on calling back into
the firmware, instead of relying on the x86 EFI handover protocol or
device tree.
- Introduce a mixed mode boot method that does not rely on the x86 EFI
handover protocol either, and could potentially be adopted by other
architectures (if another one ever surfaces where one execution mode
is a superset of another)
- Clean up the contents of struct efi, and move out everything that
doesn't need to be stored there.
- Incorporate support for UEFI spec v2.8A changes that permit firmware
implementations to return EFI_UNSUPPORTED from UEFI runtime services at
OS runtime, and expose a mask of which ones are supported or unsupported
via a configuration table.
- Various documentation updates and minor code cleanups (Heinrich)
- Partial fix for the lack of by-VA cache maintenance in the decompressor
on 32-bit ARM. Note that these patches were deliberately put at the
beginning so they can be used as a stable branch that will be shared with
a PR containing the complete fix, which I will send to the ARM tree.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEnNKg2mrY9zMBdeK7wjcgfpV0+n0FAl5S7WYACgkQwjcgfpV0
+n1jmQgAmwV3V8pbgB4mi4P2Mv8w5Zj5feUe6uXnTR2AFv5nygLcTzdxN+TU/6lc
OmZv2zzdsAscYlhuUdI/4t4cXIjHAZI39+UBoNRuMqKbkbvXCFscZANLxvJjHjZv
FFbgUk0DXkF0BCEDuSLNavidAv4b3gZsOmHbPfwuB8xdP05LbvbS2mf+2tWVAi2z
ULfua/0o9yiwl19jSS6iQEPCvvLBeBzTLW7x5Rcm/S0JnotzB59yMaeqD7jO8JYP
5PvI4WM/l5UfVHnZp2k1R76AOjReALw8dQgqAsT79Q7+EH3sNNuIjU6omdy+DFf4
tnpwYfeLOaZ1SztNNfU87Hsgnn2CGw==
=pDE3
-----END PGP SIGNATURE-----
Merge tag 'efi-next' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi into efi/core
Pull EFI updates for v5.7 from Ard Biesheuvel:
This time, the set of changes for the EFI subsystem is much larger than
usual. The main reasons are:
- Get things cleaned up before EFI support for RISC-V arrives, which will
increase the size of the validation matrix, and therefore the threshold to
making drastic changes,
- After years of defunct maintainership, the GRUB project has finally started
to consider changes from the distros regarding UEFI boot, some of which are
highly specific to the way x86 does UEFI secure boot and measured boot,
based on knowledge of both shim internals and the layout of bootparams and
the x86 setup header. Having this maintenance burden on other architectures
(which don't need shim in the first place) is hard to justify, so instead,
we are introducing a generic Linux/UEFI boot protocol.
Summary of changes:
- Boot time GDT handling changes (Arvind)
- Simplify handling of EFI properties table on arm64
- Generic EFI stub cleanups, to improve command line handling, file I/O,
memory allocation, etc.
- Introduce a generic initrd loading method based on calling back into
the firmware, instead of relying on the x86 EFI handover protocol or
device tree.
- Introduce a mixed mode boot method that does not rely on the x86 EFI
handover protocol either, and could potentially be adopted by other
architectures (if another one ever surfaces where one execution mode
is a superset of another)
- Clean up the contents of struct efi, and move out everything that
doesn't need to be stored there.
- Incorporate support for UEFI spec v2.8A changes that permit firmware
implementations to return EFI_UNSUPPORTED from UEFI runtime services at
OS runtime, and expose a mask of which ones are supported or unsupported
via a configuration table.
- Various documentation updates and minor code cleanups (Heinrich)
- Partial fix for the lack of by-VA cache maintenance in the decompressor
on 32-bit ARM. Note that these patches were deliberately put at the
beginning so they can be used as a stable branch that will be shared with
a PR containing the complete fix, which I will send to the ARM tree.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add support for booting 64-bit x86 kernels from 32-bit firmware running
on 64-bit capable CPUs without requiring the bootloader to implement
the EFI handover protocol or allocate the setup block, etc etc, all of
which can be done by the stub itself, using code that already exists.
Instead, create an ordinary EFI application entrypoint but implemented
in 32-bit code [so that it can be invoked by 32-bit firmware], and stash
the address of this 32-bit entrypoint in the .compat section where the
bootloader can find it.
Note that we use the setup block embedded in the binary to go through
startup_32(), but it gets reallocated and copied in efi_pe_entry(),
using the same code that runs when the x86 kernel is booted in EFI
mode from native firmware. This requires the loaded image protocol to
be installed on the kernel image's EFI handle, and point to the kernel
image itself and not to its loader. This, in turn, requires the
bootloader to use the LoadImage() boot service to load the 64-bit
image from 32-bit firmware, which is in fact supported by firmware
based on EDK2. (Only StartImage() will fail, and instead, the newly
added entrypoint needs to be invoked)
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Most of the EFI stub source files of all architectures reside under
drivers/firmware/efi/libstub, where they share a Makefile with special
CFLAGS and an include file with declarations that are only relevant
for stub code.
Currently, we carry a lot of stub specific stuff in linux/efi.h only
because eboot.c in arch/x86 needs them as well. So let's move eboot.c
into libstub/, and move the contents of eboot.h that we still care
about into efistub.h
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
When using the native PE entry point (as opposed to the EFI handover
protocol entry point that is used more widely), we set code32_start,
which is a 32-bit wide field, to the effective symbol address of
startup_32, which could overflow given that the EFI loader may have
located the running image anywhere in memory, and we haven't reached
the point yet where we relocate ourselves.
Since we relocate ourselves if code32_start != pref_address, this
isn't likely to lead to problems in practice, given how unlikely
it is that the truncated effective address of startup_32 happens
to equal pref_address. But it is better to defer the assignment
of code32_start to after the relocation, when it is guaranteed to
fit.
While at it, move the call to efi_relocate_kernel() to an earlier
stage so it is more likely that our preferred offset in memory has
not been occupied by other memory allocations done in the mean time.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
We have some code in the EFI stub entry point that takes the address
of the apm_bios_info struct in the newly allocated and zeroed out
boot_params structure, only to zero it out again. This is pointless
so remove it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Rearrange the instructions a bit to use a 32-bit displacement once
instead of 2/3 times. This saves 8 bytes of machine code.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Link: https://lore.kernel.org/r/20200202171353.3736319-8-nivedita@alum.mit.edu
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The limit value for the GDTR should be such that adding it to the base
address gives the address of the last byte of the GDT, i.e. it should be
one less than the size, not the size.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Link: https://lore.kernel.org/r/20200202171353.3736319-7-nivedita@alum.mit.edu
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The 64-bit kernel will already load a GDT in startup_64, which is the
next function to execute after return from efi_main.
Add GDT setup code to the 32-bit kernel's startup_32 as well. Doing it
in the head code has the advantage that we can avoid potentially
corrupting the GDT during copy/decompression. This also removes
dependence on having a specific GDT layout setup by the bootloader.
Both startup_32 and startup_64 now clear interrupts on entry, so we can
remove that from efi_main as well.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Link: https://lore.kernel.org/r/20200202171353.3736319-6-nivedita@alum.mit.edu
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
startup_32 already clears these flags on entry, do it in startup_64 as
well for consistency.
The direction flag in particular is not specified to be cleared in the
boot protocol documentation, and we currently call into C code
(paging_prepare) without explicitly clearing it.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Link: https://lore.kernel.org/r/20200202171353.3736319-5-nivedita@alum.mit.edu
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
The GDT may get overwritten during the copy or during extract_kernel,
which will cause problems if any segment register is touched before the
GDTR is reloaded by the decompressed kernel. For safety update the GDTR
to point to the GDT within the copied kernel.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Link: https://lore.kernel.org/r/20200202171353.3736319-4-nivedita@alum.mit.edu
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
When booting in mixed mode, the firmware's GDT is still installed at
handover entry in efi32_stub_entry. We save the GDTR for later use in
__efi64_thunk but we are assuming that descriptor 2 (__KERNEL_CS) is a
valid 32-bit code segment descriptor and that descriptor 3
(__KERNEL_DS/__BOOT_DS) is a valid data segment descriptor.
This happens to be true for OVMF (it actually uses descriptor 1 for data
segments, but descriptor 3 is also setup as data), but we shouldn't
depend on this being the case.
Fix this by saving the code and data selectors in addition to the GDTR
in efi32_stub_entry, and restoring them in __efi64_thunk before calling
the firmware. The UEFI specification guarantees that selectors will be
flat, so using the DS selector for all the segment registers should be
enough.
We also need to install our own GDT before initializing segment
registers in startup_32, so move the GDT load up to the beginning of the
function.
[ardb: mention mixed mode in the commit log]
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Link: https://lore.kernel.org/r/20200202171353.3736319-3-nivedita@alum.mit.edu
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
GCC 10 changed the default to -fno-common, which leads to
LD arch/x86/boot/compressed/vmlinux
ld: arch/x86/boot/compressed/pgtable_64.o:(.bss+0x0): multiple definition of `__force_order'; \
arch/x86/boot/compressed/kaslr_64.o:(.bss+0x0): first defined here
make[2]: *** [arch/x86/boot/compressed/Makefile:119: arch/x86/boot/compressed/vmlinux] Error 1
Since __force_order is already provided in pgtable_64.c, there is no
need to declare __force_order in kaslr_64.c.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200124181811.4780-1-hjl.tools@gmail.com
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are
more natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
-----BEGIN PGP SIGNATURE-----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=sv4U
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix randconfig to generate a sane .config
- rename hostprogs-y / always to hostprogs / always-y, which are more
natual syntax.
- optimize scripts/kallsyms
- fix yes2modconfig and mod2yesconfig
- make multiple directory targets ('make foo/ bar/') work
* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: make multiple directory targets work
kconfig: Invalidate all symbols after changing to y or m.
kallsyms: fix type of kallsyms_token_table[]
scripts/kallsyms: change table to store (strcut sym_entry *)
scripts/kallsyms: rename local variables in read_symbol()
kbuild: rename hostprogs-y/always to hostprogs/always-y
kbuild: fix the document to use extra-y for vmlinux.lds
kconfig: fix broken dependency in randconfig-generated .config
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when the
TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused an
infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects PCI
devices with non-maskable MSI interrupts. The problem is caused by the
non-atomic writes of the MSI address (destination APIC id) and data
(vector) fields which the device uses to construct the MSI message. The
non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after writing
address and before writing data, then the MSI block constructs a
inconsistent message which causes interrupts to be lost and subsequent
malfunction of the device.
The fix is to redirect the interrupt to the new vector on the current
CPU first and then switch it over to the new target CPU. This allows to
observe an eventually raised interrupt in the transitional stage (old
CPU, new vector) to be observed in the APIC IRR and retriggered on the
new target CPU and the new vector. The potential spurious interrupts
caused by this are harmless and can in the worst case expose a buggy
driver (all handlers have to be able to deal with spurious interrupts as
they can and do happen for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall page
which prevents resume hibernation on HYPERV guests. This change got
lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent potentially
stale IOAPIC remote IRR bits which cause stale interrupt lines after
resume.
-----BEGIN PGP SIGNATURE-----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=WxKD
-----END PGP SIGNATURE-----
Merge tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for X86:
- Ensure that the PIT is set up when the local APIC is disable or
configured in legacy mode. This is caused by an ordering issue
introduced in the recent changes which skip PIT initialization when
the TSC and APIC frequencies are already known.
- Handle malformed SRAT tables during early ACPI parsing which caused
an infinite loop anda boot hang.
- Fix a long standing race in the affinity setting code which affects
PCI devices with non-maskable MSI interrupts. The problem is caused
by the non-atomic writes of the MSI address (destination APIC id)
and data (vector) fields which the device uses to construct the MSI
message. The non-atomic writes are mandated by PCI.
If both fields change and the device raises an interrupt after
writing address and before writing data, then the MSI block
constructs a inconsistent message which causes interrupts to be
lost and subsequent malfunction of the device.
The fix is to redirect the interrupt to the new vector on the
current CPU first and then switch it over to the new target CPU.
This allows to observe an eventually raised interrupt in the
transitional stage (old CPU, new vector) to be observed in the APIC
IRR and retriggered on the new target CPU and the new vector.
The potential spurious interrupts caused by this are harmless and
can in the worst case expose a buggy driver (all handlers have to
be able to deal with spurious interrupts as they can and do happen
for various reasons).
- Add the missing suspend/resume mechanism for the HYPERV hypercall
page which prevents resume hibernation on HYPERV guests. This
change got lost before the merge window.
- Mask the IOAPIC before disabling the local APIC to prevent
potentially stale IOAPIC remote IRR bits which cause stale
interrupt lines after resume"
* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Mask IOAPIC entries when disabling the local APIC
x86/hyperv: Suspend/resume the hypercall page for hibernation
x86/apic/msi: Plug non-maskable MSI affinity race
x86/boot: Handle malformed SRAT tables during early ACPI parsing
x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode
In old days, the "host-progs" syntax was used for specifying host
programs. It was renamed to the current "hostprogs-y" in 2004.
It is typically useful in scripts/Makefile because it allows Kbuild to
selectively compile host programs based on the kernel configuration.
This commit renames like follows:
always -> always-y
hostprogs-y -> hostprogs
So, scripts/Makefile will look like this:
always-$(CONFIG_BUILD_BIN2C) += ...
always-$(CONFIG_KALLSYMS) += ...
...
hostprogs := $(always-y) $(always-m)
I think this makes more sense because a host program is always a host
program, irrespective of the kernel configuration. We want to specify
which ones to compile by CONFIG options, so always-y will be handier.
The "always", "hostprogs-y", "hostprogs-m" will be kept for backward
compatibility for a while.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Break an infinite loop when early parsing of the SRAT table is caused
by a subtable with zero length. Known to affect the ASUS WS X299 SAGE
motherboard with firmware version 1201 which has a large block of
zeros in its SRAT table. The kernel could boot successfully on this
board/firmware prior to the introduction of early parsing this table or
after a BIOS update.
[ bp: Fixup whitespace damage and commit message. Make it return 0 to
denote that there are no immovable regions because who knows what
else is broken in this BIOS. ]
Fixes: 02a3e3cdb7 ("x86/boot: Parse SRAT table and count immovable memory regions")
Signed-off-by: Steven Clarkson <sc@lambdal.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: linux-acpi@vger.kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206343
Link: https://lkml.kernel.org/r/CAHKq8taGzj0u1E_i=poHUam60Bko5BpiJ9jn0fAupFUYexvdUQ@mail.gmail.com
Pull x86 asm updates from Ingo Molnar:
"Misc updates:
- Remove last remaining calls to exception_enter/exception_exit() and
simplify the entry code some more.
- Remove force_iret()
- Add support for "Fast Short Rep Mov", which is available starting
with Ice Lake Intel CPUs - and make the x86 assembly version of
memmove() use REP MOV for all sizes when FSRM is available.
- Micro-optimize/simplify the 32-bit boot code a bit.
- Use a more future-proof SYSRET instruction mnemonic"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Simplify calculation of output address
x86/entry/64: Add instruction suffix to SYSRET
x86: Remove force_iret()
x86/cpufeatures: Add support for fast short REP; MOVSB
x86/context-tracking: Remove exception_enter/exit() from KVM_PV_REASON_PAGE_NOT_PRESENT async page fault
x86/context-tracking: Remove exception_enter/exit() from do_page_fault()
x86_64 EFI systems are unable to boot due to a typo in a recent commit:
EFI config tables not found.
-- System halted
This was probably due to the absense of CONFIG_EFI_MIXED=y in testing.
Fixes: 796eb8d26a ("efi/libstub/x86: Use const attribute for efi_is_64bit()")
Signed-off-by: Qian Cai <cai@lca.pw>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: tglx@linutronix.de
Cc: linux-efi@vger.kernel.org
Link: https://lore.kernel.org/r/20200122191430.4888-1-cai@lca.pw
Condense the calculation of decompressed kernel start a little.
Committer notes:
before:
ebp = ebx - (init_size - _end)
after:
eax = (ebx + _end) - init_size
where in both ebx contains the temporary address the kernel is moved to
for in-place decompression.
The before and after difference in register state is %eax and %ebp
but that is immaterial because the compressed image is not built with
-mregparm, i.e., all arguments of the following extract_kernel() call
are passed on the stack.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200107194436.2166846-1-nivedita@alum.mit.edu
The only users of these got removed, so they also need to be
removed to avoid warnings:
arch/x86/boot/compressed/eboot.c: In function 'setup_efi_pci':
arch/x86/boot/compressed/eboot.c:117:16: error: unused variable 'nr_pci' [-Werror=unused-variable]
unsigned long nr_pci;
^~~~~~
arch/x86/boot/compressed/eboot.c: In function 'setup_uga':
arch/x86/boot/compressed/eboot.c:244:16: error: unused variable 'nr_ugas' [-Werror=unused-variable]
unsigned long nr_ugas;
^~~~~~~
Fixes: 2732ea0d5c ("efi/libstub: Use a helper to iterate over a EFI handle array")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200113172245.27925-4-ardb@kernel.org
Reduce the stack frame of the EFI stub's mixed mode thunk routine by
8 bytes, by moving the GDT and return addresses to EBP and EBX, which
we need to preserve anyway, since their top halves will be cleared by
the call into 32-bit firmware code. Doing so results in the UEFI code
being entered with a 16 byte aligned stack, as mandated by the UEFI
spec, fixing the last occurrence in the 64-bit kernel where we violate
this requirement.
Also, move the saved GDT from a global variable to an unused part of the
stack frame, and touch up some other parts of the code.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200113172245.27925-3-ardb@kernel.org
Reshuffle the x86 stub code a bit so that we can tag the efi_is_64bit()
function with the 'const' attribute, which permits the compiler to
optimize away any redundant calls. Since we have two different entry
points for 32 and 64 bit firmware in the startup code, this also
simplifies the C code since we'll enter it with the efi_is64 variable
already set.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200113172245.27925-2-ardb@kernel.org
Introduce the ability to define macros to perform argument translation
for the calls that need it, and define them for the boot services that
we currently use.
When calling 32-bit firmware methods in mixed mode, all output
parameters that are 32-bit according to the firmware, but 64-bit in the
kernel (ie OUT UINTN * or OUT VOID **) must be initialized in the
kernel, or the upper 32 bits may contain garbage. Define macros that
zero out the upper 32 bits of the output before invoking the firmware
method.
When a 32-bit EFI call takes 64-bit arguments, the mixed-mode call must
push the two 32-bit halves as separate arguments onto the stack. This
can be achieved by splitting the argument into its two halves when
calling the assembler thunk. Define a macro to do this for the
free_pages boot service.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Matthew Garrett <mjg59@google.com>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20200103113953.9571-17-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On x86 we need to thunk through assembler stubs to call the EFI services
for mixed mode, and for runtime services in 64-bit mode. The assembler
stubs have limits on how many arguments it handles. Introduce a few
macros to check that we do not try to pass too many arguments to the
stubs.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Matthew Garrett <mjg59@google.com>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20200103113953.9571-16-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit c3710de506 ("efi/libstub/x86: Drop __efi_early() export and
efi_config struct") introduced a reference from C code in eboot.c to
the startup_32 symbol defined in the .S startup code. This results in
a GOT based reference to startup_32, and since GOT entries carry
absolute addresses, they need to be fixed up before they can be used.
On modern toolchains (binutils 2.26 or later), this reference is
relaxed into a R_386_GOTOFF relocation (or the analogous X86_64 one)
which never uses the absolute address in the entry, and so we get
away with not fixing up the GOT table before calling the EFI entry
point. However, GCC 4.6 combined with a binutils of the era (2.24)
will produce a true GOT indirected reference, resulting in a wrong
value to be returned for the address of startup_32() if the boot
code is not running at the address it was linked at.
Fortunately, we can easily override this behavior, and force GCC to
emit the GOTOFF relocations explicitly, by setting the visibility
pragma 'hidden'.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Matthew Garrett <mjg59@google.com>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20200103113953.9571-3-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The mixed mode refactor actually broke mixed mode by failing to
pass the bootparam structure to startup_32(). This went unnoticed
because it apparently has a high tolerance for being passed random
junk, and still boots fine in some cases. So let's fix this by
populating %esi as required when entering via efi32_stub_entry,
and while at it, preserve the arguments themselves instead of their
address in memory (via the stack pointer) since that memory could
be clobbered before we get to it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Matthew Garrett <mjg59@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20200103113953.9571-2-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Instead of storing the return address in a global variable when calling
a 32-bit EFI service from the 64-bit stub, avoid the indirection via
efi_exit32, and take the return address from the stack.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-26-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The macros efi_call_early and efi_call_runtime are used to call EFI
boot services and runtime services, respectively. However, the naming
is confusing, given that the early vs runtime distinction may suggest
that these are used for calling the same set of services either early
or late (== at runtime), while in reality, the sets of services they
can be used with are completely disjoint, and efi_call_runtime is also
only usable in 'early' code.
So do a global sweep to replace all occurrences with efi_bs_call or
efi_rt_call, respectively, where BS and RT match the idiom used by
the UEFI spec to refer to boot time or runtime services.
While at it, use 'func' as the macro parameter name for the function
pointers, which is less likely to collide and cause weird build errors.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-24-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
None of the definitions of the efi_table_attr() still refer to
their 'table' argument so let's get rid of it entirely.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-23-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
After refactoring the mixed mode support code, efi_call_proto()
no longer uses its protocol argument in any of its implementation,
so let's remove it altogether.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-22-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Mixed mode translates calls from the 64-bit kernel into the 32-bit
firmware by wrapping them in a call to a thunking routine that
pushes a 32-bit word onto the stack for each argument passed to the
function, regardless of the argument type. This works surprisingly
well for most services and protocols, with the exception of ones that
take explicit 64-bit arguments.
efi_free() invokes the FreePages() EFI boot service, which takes
a efi_physical_addr_t as its address argument, and this is one of
those 64-bit types. This means that the 32-bit firmware will
interpret the (addr, size) pair as a single 64-bit quantity, and
since it is guaranteed to have the high word set (as size > 0),
it will always fail due to the fact that EFI memory allocations are
always < 4 GB on 32-bit firmware.
So let's fix this by giving the thunking code a little hand, and
pass two values for the address, and a third one for the size.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-21-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We have a helper efi_system_table() that gives us the address of the
EFI system table in memory, so there is no longer point in passing
it around from each function to the next.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-20-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
As a first step towards getting rid of the need to pass around a function
parameter 'sys_table_arg' pointing to the EFI system table, remove the
references to it in the printing code, which is represents the majority
of the use cases.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-19-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The various pointers we stash in the efi_config struct which we
retrieve using __efi_early() are simply copies of the ones in
the EFI system table, which we have started accessing directly
in the previous patch. So drop all the __efi_early() related
plumbing, as well as all the assembly code dealing with efi_config,
which allows us to move the PE/COFF entry point to C code as well.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-18-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Use a single implementation for efi_char16_printk() across all
architectures.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-17-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The efi_call macros on ARM have a dependency on a variable 'sys_table_arg'
existing in the scope of the macro instantiation. Since this variable
always points to the same data structure, let's create a global getter
for it and use that instead.
Note that the use of a global variable with external linkage is avoided,
given the problems we had in the past with early processing of the GOT
tables.
While at it, drop the redundant casts in the efi_table_attr and
efi_call_proto macros.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-16-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We use special wrapper routines to invoke firmware services in the
native case as well as the mixed mode case. For mixed mode, the need
is obvious, but for the native cases, we can simply rely on the
compiler to generate the indirect call, given that GCC now has
support for the MS calling convention (and has had it for quite some
time now). Note that on i386, the decompressor and the EFI stub are not
built with -mregparm=3 like the rest of the i386 kernel, so we can
safely allow the compiler to emit the indirect calls here as well.
So drop all the wrappers and indirection, and switch to either native
calls, or direct calls into the thunk routine for mixed mode.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-14-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Annotate all the firmware routines (boot services, runtime services and
protocol methods) called in the boot context as __efiapi, and make
it expand to __attribute__((ms_abi)) on 64-bit x86. This allows us
to use the compiler to generate the calls into firmware that use the
MS calling convention instead of the SysV one.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-13-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We will soon remove another level of pointer casting, so let's make
sure all type handling involving firmware calls at boot time is correct.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-12-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Now that we have incorporated the mixed mode protocol definitions
into the native ones using unions, we no longer need the separate
32/64 bit struct definitions, with the exception of the EFI system
table definition and the boot services, runtime services and
configuration table definitions. So drop the unused ones.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-11-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
