Qcom's implementation of arm,mmu-500 works well with current
arm-smmu driver implementation. Adding a soc specific compatible
along with arm,mmu-500 makes the bindings future safe.
Signed-off-by: Vivek Gautam <vivek.gautam@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Will Deacon <will.deacon@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
There are close to 800 indivudal changesets in this branch again, which
feels like a lot. There are particularly many changes for the NVIDIA
Tegra platform this time, in fact more than it has seen in the two years
since the v4.9 merge window. Aside from this, it's been fairly normal,
with lots of changes going into Renesas R-CAR, NXP i.MX, Allwinner Sunxi,
Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5
is a minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core
Marvell Armada 8040 network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in
the BMC.
NXP i.MX usually sees a lot of new boards each release. This time there
we only add one minor variant: ConnectCore 6UL SBC Pro uses the same
SoM design as the ConnectCore 6UL SBC Express added later. However,
there is a new chip, the i.MX6ULZ, which is an even smaller variant
of the i.MX6ULL, with features removed. There is also support for the
reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute module
based on bcm2837, it was launched in early 2017 but only now added to
the kernel, both as 32-bit and as 64-bit files, as we tend to do for
Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time
are:
Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana
Pi M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit
Asus Tinker board, the model 'S' based on rk3288, and three now
boards based on the popular RK3399 chip:
ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
Rock960: https://www.96boards.org/product/rock960/
RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and
the RK3399 is the same chip used in several Chromebooks. Finally,
we get support for the PX30 (aka rk3326) chip, which is based on the
low-end 64-bit Cortex-A35 CPU core. So far, only the evaluation board
is supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is based
on the MT7622 WiFi router platform, and the first product I've seen with
a 64-bit Mediatek chip in that market: http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2),
another quad-core Cortex-A53 SoC, and its evaluation platform.
On the 32-bit side, we gain support for an actual end-user product,
the Endless Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform. This
chip is commonly known as the Snapdragon 835, and is used in high-end
phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the previously
added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the M3NULCB
Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing files,
the only board that gets added is the Toradex Colibri T20 on Colibri
Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the (formerly
Marvell) Berlin line of set-top-box chips used e.g. in the various Google
Chromecast. Only the .dtsi gets added at this point, no actual machines.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=yaED
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Arnd Bergmann:
"There are close to 800 indivudal changesets in this branch again,
which feels like a lot. There are particularly many changes for the
NVIDIA Tegra platform this time, in fact more than it has seen in the
two years since the v4.9 merge window. Aside from this, it's been
fairly normal, with lots of changes going into Renesas R-CAR, NXP
i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP.
Most of the changes are for adding new features into existing boards,
for brevity I'm only mentioning completely new machines and SoCs here.
For the first time I think we have (slightly) more new 64-bit hardware
than 32-bit:
Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a
minor variation of the motherboards of the GTA04 phone, see
https://shop.goldelico.com/wiki.php?page=GTA04A5
Clearfog is a nice little board for quad-core Marvell Armada 8040
network processor, see
https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/
Two additional server boards come with the Aspeed baseboard management
controllers: Stardragon4800 is an arm64 reference platform made by HXT
(based on Qualcomm's server chips), and TiogaPass is an Open Compute
mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the
BMC.
NXP i.MX usually sees a lot of new boards each release. This time
there we only add one minor variant: ConnectCore 6UL SBC Pro uses the
same SoM design as the ConnectCore 6UL SBC Express added later.
However, there is a new chip, the i.MX6ULZ, which is an even smaller
variant of the i.MX6ULL, with features removed. There is also support
for the reference board design, the i.MX6ULZ 14x14 EVK.
A new Raspberry Pi variant gets added, this one is the CM3 compute
module based on bcm2837, it was launched in early 2017 but only now
added to the kernel, both as 32-bit and as 64-bit files, as we tend to
do for Raspberry Pi.
On the Allwinner side, everything is again about cheap development
boards, usually of the "Fruit Pi" variety. The new ones this time are:
- Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
- Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
- Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
- Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
The last one of these is now a 64-bit version of the earlier Banana Pi
M2+ H3, with the same board layout.
Similarly, for Rockchips, get get another variant of the 32-bit Asus
Tinker board, the model 'S' based on rk3288, and three now boards
based on the popular RK3399 chip:
- ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
- Rock960: https://www.96boards.org/product/rock960/
- RockPro64: https://www.pine64.org/?page_id=61454
These are all quite powerful boards with lots of RAM and I/O, and the
RK3399 is the same chip used in several Chromebooks. Finally, we get
support for the PX30 (aka rk3326) chip, which is based on the low-end
64-bit Cortex-A35 CPU core. So far, only the evaluation board is
supported.
One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is
based on the MT7622 WiFi router platform, and the first product I've
seen with a 64-bit Mediatek chip in that market:
http://www.banana-pi.org/r64.html
For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
development board, which are similar to the Hi3660 and Hikey 360
respectively, but add support for an NPU.
Amlogic gets initial support for the Meson-G12A chip (S905D2), another
quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit
side, we gain support for an actual end-user product, the Endless
Computers Endless Mini based on Meson8b (S805), see
https://endlessos.com/computers/
Qualcomm adds support for their MSM8998 SoC and evaluation platform.
This chip is commonly known as the Snapdragon 835, and is used in
high-end phones as well as low-end laptops.
For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
but no boards for this one. However, we do add boards for the
previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the
M3NULCB Starter Kit Pro.
While we have lots of DT changes for NVIDIA to update the existing
files, the only board that gets added is the Toradex Colibri T20 on
Colibri Evaluation Board for the old Tegra2.
Synaptics add support for their AS370 SoC, which is part of the
(formerly Marvell) Berlin line of set-top-box chips used e.g. in the
various Google Chromecast. Only the .dtsi gets added at this point, no
actual machines"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits)
ARM: dts: socfgpa: remove ethernet aliases from dtsi
arm64: dts: stratix10: add ethernet aliases
dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
dt-bindings: iommu: mediatek: Add binding for MT7623
dt-bindings: clock: mediatek: add support for MT7623
ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
ARM: dts: da850-evm: Enable tca6416 on baseboard
arm64: dts: uniphier: Add USB2 PHY nodes
arm64: dts: uniphier: Add USB3 controller nodes
ARM: dts: uniphier: Add USB2 PHY nodes
ARM: dts: uniphier: Add USB3 controller nodes
arm64: dts: meson-axg: s400: disable emmc
arm64: dts: meson-axg: s400: add missing emmc pwrseq
arm64: dts: clearfog-gt-8k: add PCIe slot description
ARM: dts: at91: sama5d4_xplained: even nand memory partitions
ARM: dts: at91: sama5d3_xplained: even nand memory partitions
ARM: dts: at91: at91sam9x5cm: even nand memory partitions
ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
...
Including:
- PASID table handling updates for the Intel VT-d driver. It
implements a global PASID space now so that applications
usings multiple devices will just have one PASID.
- A new config option to make iommu passthroug mode the default.
- New sysfs attribute for iommu groups to export the type of the
default domain.
- A debugfs interface (for debug only) usable by IOMMU drivers
to export internals to user-space.
- R-Car Gen3 SoCs support for the ipmmu-vmsa driver
- The ARM-SMMU now aborts transactions from unknown devices and
devices not attached to any domain.
- Various cleanups and smaller fixes all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=TeYQ
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- PASID table handling updates for the Intel VT-d driver. It implements
a global PASID space now so that applications usings multiple devices
will just have one PASID.
- A new config option to make iommu passthroug mode the default.
- New sysfs attribute for iommu groups to export the type of the
default domain.
- A debugfs interface (for debug only) usable by IOMMU drivers to
export internals to user-space.
- R-Car Gen3 SoCs support for the ipmmu-vmsa driver
- The ARM-SMMU now aborts transactions from unknown devices and devices
not attached to any domain.
- Various cleanups and smaller fixes all over the place.
* tag 'iommu-updates-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (42 commits)
iommu/omap: Fix cache flushes on L2 table entries
iommu: Remove the ->map_sg indirection
iommu/arm-smmu-v3: Abort all transactions if SMMU is enabled in kdump kernel
iommu/arm-smmu-v3: Prevent any devices access to memory without registration
iommu/ipmmu-vmsa: Don't register as BUS IOMMU if machine doesn't have IPMMU-VMSA
iommu/ipmmu-vmsa: Clarify supported platforms
iommu/ipmmu-vmsa: Fix allocation in atomic context
iommu: Add config option to set passthrough as default
iommu: Add sysfs attribyte for domain type
iommu/arm-smmu-v3: sync the OVACKFLG to PRIQ consumer register
iommu/arm-smmu: Error out only if not enough context interrupts
iommu/io-pgtable-arm-v7s: Abort allocation when table address overflows the PTE
iommu/io-pgtable-arm: Fix pgtable allocation in selftest
iommu/vt-d: Remove the obsolete per iommu pasid tables
iommu/vt-d: Apply per pci device pasid table in SVA
iommu/vt-d: Allocate and free pasid table
iommu/vt-d: Per PCI device pasid table interfaces
iommu/vt-d: Add for_each_device_domain() helper
iommu/vt-d: Move device_domain_info to header
iommu/vt-d: Apply global PASID in SVA
...
Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN and
PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor variants
of boards/platforms.
-----BEGIN PGP SIGNATURE-----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=J0qC
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Olof Johansson:
"Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board
types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN
and PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor
variants of boards/platforms"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits)
arm64: dts: sdm845: Add tsens nodes
arm64: dts: msm8996: thermal: Initialise via DT and add second controller
arm64: dts: sprd: Add one suspend timer
arm64: dts: sprd: Add SC27XX ADC device
arm64: dts: sprd: Add SC27XX eFuse device
arm64: dts: sprd: Add SC27XX vibrator device
arm64: dts: sprd: Add SC27XX breathing light controller device
arm64: dts: meson-axg: add spdif-dit codec
arm64: dts: meson-axg: add lineout codec
arm64: dts: meson-axg: add linein codec
arm64: dts: meson-axg: add tdm interfaces
arm64: dts: meson-axg: add tdmout formatters
arm64: dts: meson-axg: add tdmin formatters
arm64: dts: meson-axg: add spdifout
arm64: dts: rockchip: add led support for Firefly-RK3399
arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399
arm64: dts: rockchip: add power button support for Firefly-RK3399
ARM: dts: aspeed: Add coprocessor interrupt controller
arm64: dts: meson-axg: add audio arb reset controller
arm64: dts: meson-axg: add usb power regulator
...
'interrupt-parent' is often documented as part of define bindings, but
it is really outside the scope of a device binding. It's never required
in a given node as it is often inherited from a parent node. Or it can
be implicit if a parent node is an 'interrupt-controller' node. So
remove it from all the binding files.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
This patch adds decriptions for mt2712 IOMMU and SMI.
In order to balance the bandwidth, mt2712 has two M4Us, two
smi-commons, 10 smi-larbs. and mt2712 is also MTK IOMMU gen2 which
uses ARM Short-Descriptor translation table format.
The mt2712 M4U-SMI HW diagram is as below:
EMI
|
------------------------------------
| |
M4U0 M4U1
| |
smi-common0 smi-common1
| |
------------------------- --------------------------------
| | | | | | | | | |
| | | | | | | | | |
larb0 larb1 larb2 larb3 larb6 larb4 larb5 larb7 larb8 larb9
disp0 vdec cam venc jpg mdp1/disp1 mdp2/disp2 mdp3 vdo/nr tvd
All the connections are HW fixed, SW can NOT adjust it.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Update the IPMMU DT binding documentation to include the compat strings
for the IPMMU devices included in the R-Car V3H and E3 SoCs.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add clock property, since we are going to control clocks in rockchip
iommu driver.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Document r8a774[35] specific compatible strings. The Renesas RZ/G1[ME]
(r8a774[35]) IPMMU are identical to the R-Car Gen2 family.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Including:
- 5-level page-table support for the Intel IOMMU.
- Error reporting improvements for the AMD IOMMU driver
- Additional DT bindings for ipmmu-vmsa (Renesas)
- Smaller fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=+LFh
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"This time there are not a lot of changes coming from the IOMMU side.
That is partly because I returned from my parental leave late in the
development process and probably partly because everyone was busy with
Spectre and Meltdown mitigation work and didn't find the time for
IOMMU work. So here are the few changes that queued up for this merge
window:
- 5-level page-table support for the Intel IOMMU.
- error reporting improvements for the AMD IOMMU driver
- additional DT bindings for ipmmu-vmsa (Renesas)
- small fixes and cleanups"
* tag 'iommu-updates-v4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Clean up of_iommu_init_fn
iommu/ipmmu-vmsa: Remove redundant of_iommu_init_fn hook
iommu/msm: Claim bus ops on probe
iommu/vt-d: Enable 5-level paging mode in the PASID entry
iommu/vt-d: Add a check for 5-level paging support
iommu/vt-d: Add a check for 1GB page support
iommu/vt-d: Enable upto 57 bits of domain address width
iommu/vt-d: Use domain instead of cache fetching
iommu/exynos: Don't unconditionally steal bus ops
iommu/omap: Fix debugfs_create_*() usage
iommu/vt-d: clean up pr_irq if request_threaded_irq fails
iommu: Check the result of iommu_group_get() for NULL
iommu/ipmmu-vmsa: Add r8a779(70|95) DT bindings
iommu/ipmmu-vmsa: Add r8a7796 DT binding
iommu/amd: Set the device table entry PPR bit for IOMMU V2 devices
iommu/amd - Record more information about unknown events
DT unit addresses should be lower case hex. Fix all the
binding examples.
Converted with the following command from Krzysztof Kozlowski:
sed -e 's/@\([a-fA-F0-9_-]*\) {/@\L\1 {/' -i $(find Documentation/devicetree/bindings -name '*.txt')
Signed-off-by: Rob Herring <robh@kernel.org>
Update the IPMMU DT binding documentation to include the
r8a77970 (R-Car V3M) and r8a77995 (R-Car D3) compat strings.
Based on work for r8a7796 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Update the IPMMU DT binding documentation to include the r8a7796 compat
string for R-Car M3-W.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Improve the binding example by removing all the leading zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
perl -p -i -e 's/\@0+([0-9a-f])/\@$1/g' `find ./Documentation/devicetree/bindings "*.txt"`
Some unnecessary changes were manually fixed.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Use the preferred generic node name in the example.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Cavium ThunderX2 SMMU doesn't support MSI and also doesn't have unique irq
lines for gerror, eventq and cmdq-sync.
New named irq "combined" is set as a errata workaround, which allows to
share the irq line by register single irq handler for all the interrupts.
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Geetha sowjanya <gakula@caviumnetworks.com>
[will: reworked irq equality checking and added SPI check]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Cavium ThunderX2 SMMU implementation doesn't support page 1 register space
and PAGE0_REGS_ONLY option is enabled as an errata workaround.
This option when turned on, replaces all page 1 offsets used for
EVTQ_PROD/CONS, PRIQ_PROD/CONS register access with page 0 offsets.
SMMU resource size checks are now based on SMMU option PAGE0_REGS_ONLY,
since resource size can be either 64k/128k.
For this, arm_smmu_device_dt_probe/acpi_probe has been moved before
platform_get_resource call, so that SMMU options are set beforehand.
Signed-off-by: Linu Cherian <linu.cherian@cavium.com>
Signed-off-by: Geetha Sowjanya <geethasowjanya.akula@cavium.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The current SMR masking support using a 2-cell iommu-specifier is
primarily intended to handle individual masters with large and/or
complex Stream ID assignments; it quickly gets a bit clunky in other SMR
use-cases where we just want to consistently mask out the same part of
every Stream ID (e.g. for MMU-500 configurations where the appended TBU
number gets in the way unnecessarily). Let's add a new property to allow
a single global mask value to better fit the latter situation.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Nipun Gupta <nipun.gupta@nxp.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The generic IOMMU binding says that the meaning of an 'IOMMU specifier'
is defined by the binding of a specific SMMU. The ARM SMMU binding
never explicitly uses the term 'specifier' at all. Update implicit
references to use the explicit term.
In the iommu-map binding change references to iommu-specifier to
"IOMMU specifier" so we are 100% consistent everywhere with terminology
and capitalization.
Signed-off-by: Stuart Yoder <stuart.yoder@nxp.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Document how the generic "iommus" binding should be used to describe ARM
SMMU stream IDs instead of the old "mmu-masters" binding.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We're about to ratify our use of the generic binding, so document it.
CC: Rob Herring <robh+dt@kernel.org>
CC: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This may well be the world's most inconsequential patch, but there is a
spelling mistake that needs fixing and Andrea was bored enough to write
the patch (along with 1528 others...).
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
The MSM IOMMU is an implementation compatible with the ARM VMSA short
descriptor page tables. It provides address translation for bus masters outside
of the CPU, each connected to the IOMMU through a port called micro-TLB.
Adding the DT bindings for the same.
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch defines the local arbitor port IDs for mediatek SoC MT2701 and
add descriptions of binding for mediatek generation one iommu and smi.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Due to erratum #27704, the CN88xx SMMUv2 implementation supports only
shared ASID and VMID numberspaces.
This patch ensures that ASID and VMIDs are unique across all SMMU
instances on affected Cavium systems.
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
Signed-off-by: Akula Geethasowjanya <Geethasowjanya.Akula@caviumnetworks.com>
[will: commit message, comments and formatting]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Update the IPMMU DT binding documentation to include the r8a7795 compat
string as well as the "renesas,ipmmu-main" property that on r8a7795 will
be used to describe the topology and the relationship between the various
cache IPMMU instances and the main IPMMU.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch adds support for v5 of SYSMMU controller, found in Samsung
Exynos 5433 SoCs. The main difference of v5 is support for 36-bit physical
address space and some changes in register layout and core clocks hanging.
This patch also adds support for ARM64 architecture, which is used by
Exynos 5433 SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Exynos SYSMMU bindings documentation was merged before generic IOMMU
binding have been introduced. This patch updates documentation to match
current state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Add part numbers for APE6 and current set of R-Car Gen2 SoCs to the
IPMMU DT binding documentation. The example is also updated to show
how the generic compatible string may be used as fallback.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
As usual, this is the massive branch we have for each release. Lots of
various updates and additions of hardware descriptions on existing hardware,
as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and 32-bit
DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to tell
from the diffstat, so there's little point in duplicating listing it here.)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qY1q
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As usual, this is the massive branch we have for each release. Lots
of various updates and additions of hardware descriptions on existing
hardware, as well as the usual additions of new boards and SoCs.
This is also the first release where we've started mixing 64- and
32-bit DT updates in one branch.
(Specific details on what's actually here and new is pretty easy to
tell from the diffstat, so there's little point in duplicating listing
it here)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (499 commits)
ARM: dts: uniphier: add system-bus-controller nodes
ARM64: juno: disable NOR flash node by default
ARM: dts: uniphier: add outer cache controller nodes
arm64: defconfig: Enable PCI generic host bridge by default
arm64: Juno: Add support for the PCIe host bridge on Juno R1
Documentation: of: Document the bindings used by Juno R1 PCIe host bridge
ARM: dts: uniphier: add I2C aliases for ProXstream2 boards
dts/Makefile: Add build support for LS2080a QDS & RDB board DTS
dts/ls2080a: Add DTS support for LS2080a QDS & RDB boards
dts/ls2080a: Update Simulator DTS to add support of various peripherals
dts/ls2080a: Remove text about writing to Free Software Foundation
dts/ls2080a: Update DTSI to add support of various peripherals
doc: DTS: Update DWC3 binding to provide reference to generic bindings
doc/bindings: Update GPIO devicetree binding documentation for LS2080A
Documentation/dts: Move FSL board-specific bindings out of /powerpc
Documentation: DT: Add entry for FSL LS2080A QDS and RDB boards
arm64: Rename FSL LS2085A SoC support code to LS2080A
arm64: Use generic Layerscape SoC family naming
ARM: dts: uniphier: add ProXstream2 Vodka board support
ARM: dts: uniphier: add ProXstream2 Gentil board support
...
Exynos SoC Device Tree bindings are spread over arm/exynos/ and
arm/samsung/ directories. There is no need for that separation and it
actually confuses. Put power domain bindings under power/ and
remaining samsung-boards.txt under arm/samsung/.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Despite being a platform device, the SMMUv3 is capable of signaling
interrupts using MSIs. Hook it into the platform MSI framework and
enjoy faults being reported in a new and exciting way.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[will: tidied up the binding example and reworked most of the code]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The DSP processor sub-systems on DRA7xx have two MMU instances
each, one for the processor core and the other for an internal
EDMA block. These MMUs need an additional shared register to be
programmed in the DSP_SYSTEM sub-module to be enabled properly.
The OMAP IOMMU bindings is updated to account for this additional
syscon property required for these DSP IOMMU instances on DRA7xx
SoCs. A new compatible "ti,dra7-dsp-iommu" is also defined to
distinguish these devices specifically from other DRA7 IOMMU
devices.
An example of the DRA7 DSP IOMMU nodes is also added to the
document for clarity.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
The OMAP IOMMU bindings is updated to reflect the required #iommu-cells
property.
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
