Now that kernel-doc can hanle nested structs/unions, describe
such fields at w1_netlink_message_types.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The w1 master driver includes a complete open drain emulation
reimplementation among other things.
This converts the driver and all board files using it to use
GPIO descriptors associated with the device to look up the
GPIO wire, as well ass the optional pull-up GPIO line.
When probed from the device tree, the driver will just pick
descriptors and use them right off. For the two board files
in the kernel, we add descriptor lookups so we do not need
to keep any old platform data handling around for the GPIO
lines.
As the platform data is also a state container for this driver,
we augment it to contain the GPIO descriptors.
w1_gpio_write_bit_dir() and w1_gpio_write_bit_val() are gone
since this pair was a reimplementation of open drain emulation
which is now handled by gpiolib.
The special "linux,open-drain" flag is a bit of mishap here:
it has the same semantic as the same flags in I2C: it means
that something in the platform is setting up the line as
open drain behind our back. We handle this the same way as
in I2C.
To drive the pull-up, we need to bypass open drain emulation
in gpiolib for the line, and this is done by driving it high
using gpiod_set_raw_value() which has been augmented to have
the semantic of overriding the open drain emulation.
We also augment the documentation to reflect the way to pass
GPIO descriptors from the machine.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Here is the big set of char/misc and other driver subsystem patches for
4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
Note, there will be a merge conflict in drivers/misc/lkdtm_core.c when
merging to your tree as one lkdtm patch came in through the perf tree as
well as this one. The resolution is to take the const change that this
tree provides.
All of these have been in linux-next for quite a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWg2Lnw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymTUwCgwp46+I8yPlgDH8oe5TxyyJnpdHQAn1XW0i+a
sBi6WS87In5v1QO1Rgfc
=dH2a
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc updates from Greg KH:
"Here is the big set of char/misc and other driver subsystem patches
for 4.15-rc1.
There are small changes all over here, hyperv driver updates, pcmcia
driver updates, w1 driver updats, vme driver updates, nvmem driver
updates, and lots of other little one-off driver updates as well. The
shortlog has the full details.
All of these have been in linux-next for quite a while with no
reported issues"
* tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
VME: Return -EBUSY when DMA list in use
w1: keep balance of mutex locks and refcnts
MAINTAINERS: Update VME subsystem tree.
nvmem: sunxi-sid: add support for A64/H5's SID controller
nvmem: imx-ocotp: Update module description
nvmem: imx-ocotp: Enable i.MX7D OTP write support
nvmem: imx-ocotp: Add i.MX7D timing write clock setup support
nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function
nvmem: imx-ocotp: Add support for banked OTP addressing
nvmem: imx-ocotp: Pass parameters via a struct
nvmem: imx-ocotp: Restrict OTP write to IMX6 processors
nvmem: uniphier: add UniPhier eFuse driver
dt-bindings: nvmem: add description for UniPhier eFuse
nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset
nvmem: qfprom: fix different address space warnings of sparse
nvmem: mtk-efuse: fix different address space warnings of sparse
nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it
nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it
thunderbolt: tb: fix use after free in tb_activate_pcie_devices
MAINTAINERS: Add git tree for Thunderbolt development
...
w1_therm_eeprom() and w1_DS18B20_precision() decrement THERM_REFCNT
on error paths, while they did not increment it yet.
read_therm() unlocks bus mutex on some error paths,
while it is not acquired.
The patch makes sure all the functions keep the balance in usage of
the mutex and the THERM_REFCNT.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This subpatch adds a driver for the DS28E17 Onewire to I2C master bridge.
Signed-off-by: Jan Kandziora <jjj@gmx.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The w1_ds28e17 driver from the next part of this patch needs to emit
single-bit read timeslots to the DS28E17. The w1 subsystem already
has this function but it is not exported outside drivers/w1/w1_io.c
This subpatch exports the w1_touch_bit symbol with EXPORT_SYMBOL_GPL,
same as the other exported symbols in drivers/w1/w1_io.c
May be also useful later for writing drivers for other Onewire chips
which do single-bit communication.
Signed-off-by: Jan Kandziora <jjj@gmx.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inside the w1_slave_show function refactor the code to read the temp
into a separate function.
Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a one wire driver for the DS28E05 one wire slave chip. This chip
requires OverDrive support to talk to it.
Signed-off-by: Andrew Worsley <amworsley@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the one wire DS2482 master driver with a module option that allows support
for PPM/SPU/1WS interface modes to be requested. This allows support of chips
that require one or more of these features such as the DS28E05.
Signed-off-by: Andrew Worsley <amworsley@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The functions w1_ds2438_get_page, w1_ds2438_get_temperature,
w1_ds2438_change_config_bit and w1_ds2438_get_voltage are local to
the source and do not need to be in global scope, so make it static.
Cleans up sparse warnings:
symbol 'w1_ds2438_get_page' was not declared. Should it be static?
symbol 'w1_ds2438_get_temperature' was not declared. Should it be static?
symbol 'w1_ds2438_change_config_bit' was not declared. Should it be static?
symbol 'w1_ds2438_get_voltage' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1: ds1wm: silence interrupts on HW before claiming the interrupt.
This way avoid possible invalid interrupts in the initialization phase.
Signed-off-by: Johannes Poehlmann <johannes.poehlmann@izt-labs.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
o Make endian clean, make HW-endianness configurable.
o Use ioread*, iowrite* instead of __raw_readb,__raw_writeb
to also use memory-barriers when accessing HW-registers.
We do not want reordering to happen here.
Both changes are tightly coupled, so I do them in one patch
Signed-off-by: Johannes Poehlmann <johannes.poehlmann@izt-labs.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace incorrect register offsett calculation by
direct configuration of bus_shift in mfd-cell.
Indirect definition of address-shift by resource size
was unobvious and was wrong (should have used a binary log).
Signed-off-by: Johannes Poehlmann <johannes.poehlmann@izt-labs.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_device_id are not supposed to change at runtime. All functions
working with usb_device_id provided by <linux/usb.h> work with
const usb_device_id. So mark the non-const structs as const.
Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
attribute_group are not supposed to change at runtime. All functions
working with attribute_group provided by <linux/sysfs.h> work with
const attribute_group. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The HDQ interface driver should be in this folder just like the I2C
interface driver. Move this driver out of drivers/w1/slave and into
drivers/power/supply.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
platform_get_irq() returns an error code, but the omap_hdq
driver ignores it and always returns -ENXIO. This is not correct,
and prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error.
Print error message and propagate the return value of
platform_get_irq on failure.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1-Wire bus have very fast algorith for exchange with single slave
device. Fix incorrect count of slave devices on connect second slave
device. This case on slave device probe() step we need use generic
(multislave) functions for read/write device.
Signed-off-by: Alex A. Mihaylov <minimumlaw@rambler.ru>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Like other subsystems we should be able to define slave devices outside
of the w1 directory. To do this we move public facing interface
definitions to include/linux/w1.h and rename the internal definition
file to w1_internal.h.
As w1_family.h and w1_int.h contained almost entirely public
driver interface definitions we simply removed these files and
moved the remaining definitions into w1_internal.h.
With this we can now start to move slave devices out of w1/slaves and
into the subsystem based on the function they implement, again like
other drivers.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Structures and functions should be ordered such that forward declaration
use is minimized.
MODULE_* macros should immediately follow the structures and functions
upon which they act.
Remaining MODULE_* macros should be at the end of the file in
alphabetical order.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only use of assert() is in matrox_w1.c and is used to check the input
to probe() from the PCI subsystem for NULL values, these are guaranteed
to be populated and no other PCI driver makes this check, remove this.
As this was the only definition in w1_log.h, remove this also.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detailed information about support and provided sysfs files
in my next commit which creates a documentation file:
Documentation/w1/slaves/w1_ds2438
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We are going to split <linux/sched/signal.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.
Create a trivial placeholder <linux/sched/signal.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.
Include the new header in the files that are going to need it.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
module_w1_family() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kmemdup rather than duplicating its implementation.
Generated by: scripts/coccinelle/api/memdup.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove filename from file, this is not done anymore as it doesn't
add anything and usually is incorrect as filename change often.
Also shorten the GPL to the more common address-less version and
remove excess white-space.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Near the beginning of w1_attach_slave_device() we increment a w1 master
reference count.
Later, when we are going to exit this function without actually attaching
a slave device (due to failure of __w1_attach_slave_device()) we need to
decrement this reference count back.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Cc: stable@vger.kernel.org
Fixes: 9fcbbac5de ("w1: process w1 netlink commands in w1_process thread")
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds a driver for a DS2405 1-wire single-channel addressable switch.
The DS2405 can also work as a single-channel binary remote sensor.
This driver supports two attributes: "state" and "output" which are the
same attribute names as supported by existing DS2406, DS2408 and DS2413
drivers.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ds2490 driver was doing USB transfers from / to buffers on a stack.
This is not permitted and made the driver non-working with vmapped stacks.
Since all these transfers are done under the same bus_mutex lock we can
simply use shared buffers in a device private structure for two most common
of them.
While we are at it, let's also fix a comparison between int and size_t in
ds9490r_search() which made the driver spin in this function if state
register get requests were failing.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Cc: stable <stable@vger.kernel.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error returned by '_omap_hdq_reset()', free resources as done
elsewhere in this function.
This patch slighly changes the semantic of the code. It now propagates the
error code returned by '_omap_hdq_reset()' instead of returning -EINVAL
unconditionally.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct pointer notations to include whitespace between
variable type and "*" character. Inserted blank line
after variable declatations at two locations.
Rearranged comparison within an if statment to have the
constant on the right-hand side.
Signed-off-by: Ben Werbowyj <ben.werbowyj@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Assignment of variable count removed from within an if statment.
This was done at two locations in the file.
Signed-off-by: Ben Werbowyj <ben.werbowyj@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Inserted whitespace between command and open parenthesis
at two locations. Removed new line between open brace and
command/declaration at two locations.
Signed-off-by: Ben Werbowyj <ben.werbowyj@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit e93762bbf6 ("w1: masters: omap_hdq: add support for 1-wire
mode") added a statement to clear the hdq_irqstatus flags in
hdq_read_byte().
If the hdq reading process is scheduled slowly or interrupts are
disabled for a while the hardware read activity might already be
finished on entry of hdq_read_byte(). And hdq_isr() already has set the
hdq_irqstatus to 0x6 (can be seen in debug mode) denoting that both, the
TXCOMPLETE and RXCOMPLETE interrupts occurred in parallel.
This means there is no need to wait and the hdq_read_byte() can just
read the byte from the hdq controller.
By resetting hdq_irqstatus to 0 the read process is forced to be always
waiting again (because the if statement always succeeds) but the
hardware will not issue another RXCOMPLETE interrupt. This results in a
false timeout.
After such a situation the hdq bus hangs.
Link: http://lkml.kernel.org/r/b724765f87ad276a69625bc19806c8c8844c4590.1469513669.git.hns@goldelico.com
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The helper macro module_w1_family can be used in module drivers that
only register a w1 driver in their module init functions. Add this
macro and use it in all applicable drivers.
Link: http://lkml.kernel.org/r/20160531204313.20979-2-afd@ti.com
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PLATFORM_DEVID_AUTO can be used to have the platform core assign a
unique ID instead of manually creating one with IDA. Do this in all
applicable drivers.
Link: http://lkml.kernel.org/r/20160531204313.20979-1-afd@ti.com
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since many temperature sensors come "preconfigured" with a lower
precision, people are stuck at that precision when running on a kernel
based device (unlike the Dallas 1Wire library for e.g. Arduino, which
supports writing the configuration/scratchpad). This patch adds write
support for the scratchpad/precision registers via w1_slave sysfs.
Signed-off-by: Ben Sen <0.x29a.0@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If kstrtoint() returns -ERANGE then "tmp" is uninitialized.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Evgeniy Polaykov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit enables the active pullup (APU bit) by default for
the DS2482 1-Wire master.
>From the DS2482 datasheet:
"The APU bit controls whether an active pullup (controlled slew-rate
transistor) or a passive pullup (Rwpu resistor) will be used to drive
a 1-Wire line from low to high. When APU = 0, active pullup is disabled
(resistor mode). Active Pullup should always be selected unless there is
only a single slave on the 1-Wire line."
According to the module author, Ben Gardner:
"It doesn't look like active pullup would cause any hurt if there
is only a single slave."
And my tests with multiple and single slaves on 1-Wire bus
confirms that.
This active pullup can be manually disabled using the introduced
module parameter:
active_pullup = 0
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_process() calls try_to_freeze(), but the thread doesn't mark itself
freezable through set_freezable(), so the try_to_freeze() call is useless.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
hdq_usecount was set to zero after a successful read, so
omap_hdq_put could not properly free resources which leads
e.g. to increasing usecounts in lsmod output
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's stop using legacy platform driver hooks for power management and
switch to using the standard dev_pm_ops-based hooks.
Also, instead of guarding PM methods with #ifdef CONFIG_PM annotate them
as __maybe_unused as it provides better compile coverage.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patches makes following changes to omap_hdq driver
- Enable 1-wire mode.
- Implement w1_triplet callback to facilitate search rom
procedure and auto detection of 1-wire slaves.
- Proper enabling and disabling of interrupt.
- Cleanups (formatting and return value checks).
HDQ mode remains unchanged.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, memsetting and kfreeing the device is bad behaviour. The
device will have a reference count of 1 and hence can cause trouble
because it has kfree'd. Proper way to handle a failed device_register is
to call put_device right after it fails.
Signed-off-by: Levente Kurusa <levex@linux.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When initialized as a platform device the initializer must now specify
a device. An empty device name is no longer valid.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Rename functions that are used by multiple devices. New devices
have been added and the function names and driver name are no longer
general enough for the functionality they provide.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: GUAN Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Use module_pci_driver for drivers whose init and exit functions
only register and unregister, respectively.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@a@
identifier f, x;
@@
-static f(...) { return pci_register_driver(&x); }
@b depends on a@
identifier e, a.x;
@@
-static e(...) { pci_unregister_driver(&x); }
@c depends on a && b@
identifier a.f;
declarer name module_init;
@@
-module_init(f);
@d depends on a && b && c@
identifier b.e, a.x;
declarer name module_exit;
declarer name module_pci_driver;
@@
-module_exit(e);
+module_pci_driver(x);
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed there was a problem here because Smatch complained:
drivers/w1/slaves/w1_therm.c:416 w1_seq_show() warn:
inconsistent returns 'mutex:&sl->master->mutex'.
Locked on: line 416
Unlocked on: line 413
The problem is that we lock ->mutex but we unlock ->bus_mutex on error.
David Fries says that ->bus_mutex is correct and ->mutex is incorrect.
Fixes: d9411e57dc ('w1: Add support for DS28EA00 sequence to w1-therm')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The W1_42_FINISHED_BYTE is 0xFF so the cast means the condition is
never true.
Fixes: d9411e57dc ('w1: Add support for DS28EA00 sequence to w1-therm')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add i2c alias to enable autoloading of the module for device specified
in device-tree.
Signed-off-by: Ludek Hlavacek <ludek_h@seznam.cz>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch provides support for the DS28EA00 digital thermometer.
The DS28EA00 provides an additional two pins for implementing a sequence
detection algorithm. This feature allows you to determine the physical
location of the chip in the 1-wire bus without needing pre-existing
knowledge of the bus ordering. Support is provided through the sysfs
w1_seq file. The file will contain a single line with an integer value
representing the device index in the bus starting at 0.
Signed-off-by: Matt Campbell <mattrcampbell@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A temperature conversion can take 750 ms and when possible the
w1_therm slave driver drops the bus_mutex to allow other bus
operations, but that includes operations such as a periodic slave
search, which can remove this slave when it is no longer detected.
If that happens the sl->family_data will be freed and set to NULL
causing w1_slave_show to crash when it wakes up.
Signed-off-by: David Fries <David@Fries.net>
Reported-By: Thorsten Bschorr <thorsten@bschorr.de>
Tested-by: Thorsten Bschorr <thorsten@bschorr.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of 1-Wire devices commonly associated with physical access control
systems are attached/generate presence for as short as 100 ms - hence
the tens-to-hundreds milliseconds scan intervals are required.
Signed-off-by: Dmitry Khromov <dk@icelogic.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a new
subsystem, "coresight" has been added. Full details are in the
shortlog.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSODosACgkQMUfUDdst+ykSNwCfcqx1Z3rQzbLwSrR2sa1fV3Zb
yEAAniJoLZ4ZkoQK4/1ozsFc31q+gXNm
=/epr
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the big char/misc driver update for 3.19-rc1
Lots of little things all over the place in different drivers, and a
new subsystem, "coresight" has been added. Full details are in the
shortlog"
* tag 'char-misc-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (73 commits)
parport: parport_pc, do not remove parent devices early
spmi: Remove shutdown/suspend/resume kernel-doc
carma-fpga-program: drop videobuf dependency
carma-fpga: drop videobuf dependency
carma-fpga-program.c: fix compile errors
i8k: Fix temperature bug handling in i8k_get_temp()
cxl: Name interrupts in /proc/interrupt
CXL: Return error to PSL if IRQ demultiplexing fails & print clearer warning
coresight-replicator: remove .owner field for driver
coresight: fixed comments in coresight.h
coresight: fix typo in comment in coresight-priv.h
coresight: bindings for coresight drivers
coresight: Adding ABI documentation
w1: support auto-load of w1_bq27000 module.
w1: avoid potential u16 overflow
cn: verify msg->len before making callback
mei: export fw status registers through sysfs
mei: read and print all six FW status registers
mei: txe: add cherrytrail device id
mei: kill cached host and me csr values
...
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
1/ change request_module call to zero-pad single digit
family numbers. This appears to be the intention of
the code, but not what it actually does.
This means that the alias created for W1_FAMILY_SMEM_01
might actually be useful.
2/ Define a family name for the BQ27000 battery charge monitor.
Unfortunately this is the same number as W1_FAMILY_SMEM_01
so if both a compiled on a system, one module might need to
be blacklisted.
3/ Add a MODULE_ALIAS for the bq27000.
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver has no 'compatible' string and so is not found when
using device-tree.
Add one with value to match
hdqw1w: 1w@480b2000 {
device in omap3.dtsi.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adjust the bulk message timeout to the other ones (1000ms). Otherwise the
following dmesg errors can be seen on a Raspberry Pi:
[ 31.492386] Failed to read 1-wire data from 0x81: err=-110.
[ 31.504168] 0x81: count=-110, status:
[ 31.613404] Failed to read 1-wire data from 0x81: err=-110.
[ 31.621915] 0x81: count=-110, status:
[ 43.260968] Failed to read 1-wire data from 0x81: err=-110.
[ 43.270998] 0x81: count=-110, status:
[ 43.379959] Failed to read 1-wire data from 0x81: err=-110.
[ 43.388854] 0x81: count=-110, status:
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94859308a2 "w1: new w1_ds2406 driver" added a new driver
that uses the crc16 library, but didn't ensure that the core is
there. This adds the necessary Kconfig statements, just like we
have it for other w1 drivers.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Scott Alfter <scott@alfter.us>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces all calls to the "printk" function within the "masters"
subdirectory by calls to the appropriate "pr_*" function thus addressing
the following warning generated by the checkpatch script:
WARNING: Prefer [subsystem eg: netdev]_err([subsystem]dev, ...
then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Fjodor Schelichow <fjodor.schelichow@hotmail.com>
Signed-off-by: Roman Sommer <romsom2@yahoo.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces all calls to the "printk" function within the main "w1"
directory by calls to the appropriate "pr_*" function thus addressing
the following warning generated by the checkpatch script:
WARNING: Prefer [subsystem eg: netdev]_err([subsystem]dev, ...
then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Fjodor Schelichow <fjodor.schelichow@hotmail.com>
Signed-off-by: Roman Sommer <romsom2@yahoo.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces all calls to the "printk" function within the "slaves"
subdirectory by calls to the appropriate "pr_*" function thus addressing
the following warning generated by the checkpatch script:
WARNING: Prefer [subsystem eg: netdev]_err([subsystem]dev, ...
then dev_err(dev, ... then pr_err(... to printk(KERN_ERR ...
Signed-off-by: Fjodor Schelichow <fjodor.schelichow@hotmail.com>
Signed-off-by: Roman Sommer <romsom2@yahoo.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some preliminary work at making use of this driver led me to implement
CRC-16 checks on read and write to deal with the occasional glitchiness of
the 1-Wire bus. The revised driver (attached) returns an I/O error if the
CRC check fails. When reading the chip's state, either you get a valid
indication or you get an I/O error. When changing its state, either the
change is successful or an I/O error is returned.
Signed-off-by: Scott Alfter <scott@alfter.us>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace spaces at beginning of the string with tabs, and replace foo * bar with foo *bar in a pointer declaration.
Signed-off-by: Thomas Wood <tommyandrena@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the i.MX reference manual, the read/write bit operations
takes from 60 us to 120 us.
This patch optimizes mxc_w1_ds2_touch_bit() function to use proper
value for such delay. Nevertheless, a small margin for the timeout has
been added for the case if clock frequency is inaccurate.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a software reset for 1-Wire module at driver startup.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the i.MX reference manual, the reset procedure and
"presence" pulse takes 511 and 512 us, respectively. Measurement for
i.MX27 is about 1100 us. There is no need to wait Reset+Presence
more than this time.
This patch optimizes mxc_w1_ds2_reset_bus() function to use proper
value for delay after w1 bus reset. Nevertheless, a small margin for
the timeout has been added for the case if clock frequency is inaccurate.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
W1 reset_bus() should return zero if slave device is present.
This patch fix this issue.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
w1_process_callbacks() expects to be called with dev->list_mutex held,
but it is the fact only in w1_process(). __w1_remove_master_device()
calls w1_process_callbacks() after it releases list_mutex.
The patch fixes __w1_remove_master_device() to acquire list_mutex
for w1_process_callbacks().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: David Fries <david@fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: stable <stable@vger.kernel.org> # 3.15
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Applications can submit a set of commands in one packet to the kernel,
and in some cases it is required such as reading the temperature
sensor results. This adds an option W1_CN_BUNDLE to the flags of
cn_msg to request the kernel to reply in one packet for efficiency.
The cn_msg flags now check for unknown flag values and return an error
if one is seen. See "Proper handling of unknown flags in system
calls" http://lwn.net/Articles/588444/
This corrects the ack values returned as per the protocol standard,
namely the original ack for status messages and seq + 1 for all others
such as the data returned from a read.
Some of the common variable names have been standardized as follows.
struct cn_msg *cn
struct w1_netlink_msg *msg
struct w1_netlink_cmd *cmd
struct w1_master *dev
When an argument and a function scope variable would collide, add req_
to the argument.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
__w1_attach_slave_device calls device_add which calls w1_bus_notify
which calls the w1_bq27000 slave driver, which calls
platform_device_add and device_add and deadlocks on getting
&(&priv->bus_notifier)->rwsem as it is still held in the previous
device_add. This avoids the problem by processing the family
add/remove outside of the slave device_add call.
Commit 47eba33a09 introduced this deadlock and added
a KOBJ_ADD, as the add was already reported in device_register two add
events were being sent. This change suppresses the device_register
add so that any slave device sysfs entries are setup before the add
goes out.
Belisko Marek reported this change fixed the deadlock he was seeing on
ARM device tree, while testing on my x86-64 system never saw the
deadlock.
Reported-by: Belisko Marek <marek.belisko@gmail.com>
Signed-off-by: David Fries <David@Fries.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the message type is W1_MASTER_CMD or W1_SLAVE_CMD, then a reference
is taken when searching for the slave or master device. If there
isn't any following data m->len (mlen is a copy) is 0 and packing up
the message for later execution is skipped leaving nothing to
decrement the reference counts.
Way back when, m->len was checked before the search that increments the
reference count, but W1_LIST_MASTERS has no additional data, the check
was moved in 9be62e0b2f causing this bug.
This change reorders to put the check before the reference count is
incremented avoiding the problem.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This helps increasing build testing coverage.
To do this, __raw_{read,write}b() functions was be replaced with
simple {read,write}b() variants.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Remove old and currently wrong address of the FSF from license
parts of the code.
- Remove unused #include and sort remaining headers alphabetically.
- Remove unised definitions.
- Add definitions for bit-fields.
- Add missing module owner field.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix mxc_w1_ds2_reset_bus() return value.
According to i.MX reference manual, "presence status" reflected
in the bit 6 of control register.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Configuration for masters and slaves is included only if W1 symbol
enabled, so no reason to check it once more.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_get_gpio() might return -EPROBE_DEFER meaning that the driver
providing the gpio isn't ready yet. If that happens for the first gpio
the resulting kernel output without this patch is:
w1-gpio somename: Failed to parse DT
platform somename: Driver w1-gpio requests probe deferral
The first message is misleading and so is suppressed with this patch.
Further if determining the gpio to switch the external pullup yields
-EPROBE_DEFER this error should be passed back to the caller instead of
just continuing without pullup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On 64 bit systems, a large value for "long tmp" is truncated when
assigning to "int md->max_slave_count" so we still end up with a value
less than one despite the "tmp < 1" check.
This is more of a problem for static checkers than a real life issue,
but it's simple enough to fix.
Acked-by: David Fries <david@fries.net>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts ds1wm.c from commit d3a8a9dbb9.
Of the three files changed ds1wm.c ds2490.c and w1_netlink.c, it turns out
ds1wm.c was locking bus_mutex, but inside the loop and I missed it.
Reverting ds1wm.c to the previous version.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David Fries <David@Fries.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bus_mutex needs to be taken to serialize access to a specific bus.
netlink wasn't updated when bus_mutex was added and was calling
without that lock held, and not all of the masters were holding the
bus_mutex in a search. This was causing the ds2490 hardware to stop
responding when both netlink and /sys slaves were executing bus
commands at the same time.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Switch the code documentation format style to DocBook format, enable
DocBook documentation generation, and fix some comments.
Signed-off-by: David Fries <David@Fries.net>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
