MOTU 828mk2 is one of second generation in MOTU FireWire series, produced in
2003. This model consists of four chips:
* TI TSB41AB2 (Physical layer for IEEE 1394 bus)
* PDI 1394L40BE (Link layer for IEEE 1394 bus and packet processing layer)
* ALTERA ACEX 1K EP1K30 Series FPGA (Data block processing layer)
* TI TMS320VC5402 (Digital signal processing)
This commit adds a support for this model, with its unique protocol as
version 2. The features of this protocol are:
* Support data chunks for status and control messages for both
directions.
* Support a pair of MIDI input/output.
* Support a data chunk for mic/instrument independent of analog line in.
* Support a data chunk for playback return.
* Support independent data chunks for S/PDIF of both optical/coaxial
interfaces.
* Support independent data chunks for each of main out and phone out.
Status of clock is configured by write transactions to 0x'ffff'f000'0b14.
Modes of optical interfaces are configured by write transactions to
0x'ffff'f000'0c04.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds an new driver for MOTU FireWire series. In this commit,
this driver just creates/removes card instance according to bus event.
More functionalities will be added in following commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I forgot it.
Fixes: 3e78e1518e12('ALSA: firewire-tascam: add support for FW-1804')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now ALSA oxfw driver gains functionalities which scs1x module has.
This commit obsoletes the scs1x module, and adds a line of MODULE_ALIAS
to load oxfw module instead of scs1x module.
In scs1x module, the name of 'shortname' field is fixed as 'SCS1x'. This
field is used to name MIDI ports for both of SCS.1m and SCS.1d. This is
not good because typically some SCS.1m and SCS.1d are used in the same
system. It's better to distinguish them according to name of the ports.
This commit applies model name in config ROM to the 'shortname'.
For the name of 'driver' and 'longname', this commit uses the same way
applied to the other models. This change may not bring disadvantages to
users because userspace applications use ALSA rawmidi or seq interface
and these interfaces are not influenced by them directly.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A commit to add support for this model should have added a comment
about this model to Kconfig.
Fixes: 759a2f40c9fa('ALSA: oxfw: add an entry for TASCAM FireOne')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other IEEE 1394 sound devices
has.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for TASCAM FireWire series. In this commit,
this driver just creates/removes card instance according to bus event.
More functionalities will be added in following commits.
TASCAM FireWire series consists of:
* PDI 1394P23 for IEEE 1394 PHY layer
* PDI 1394L40 for IEEE 1394 LINK layer and IEC 61883 interface
* XILINX XC9536XL
* XILINX Spartan-II XC2S100
* ATMEL AT91M42800A
Ilya Zimnovich had investigated TASCAM FireWire series in 2011, and
discover some features of his FW-1804. You can see a part of his research
in FFADO project.
http://subversion.ffado.org/wiki/Tascam
A part of my work are based on Ilya's investigation, while this series
doesn't support the FW-1804, because of a lack of config ROM
information and its protocol detail, especially for PCM channels.
I observed that FW-1884 and FW-1082 don't work properly with 1394 OHCI
controller based on VT6315. The controller can actually communicate packets
to these models, while these models generate no sounds. It may be due to
the PHY/LINK layer issues. Using 1394 OHCI controller produced by the other
vendors such as Texas Instruments may work. Or adding another node on the
bus.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds hwdep interface so as the other sound drivers for units
on IEEE 1394 bus have.
This interface is designed for mixer/control applications. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for Digidesign 002/003 family. This commit
just creates/removes card instance according to bus event. More functions
will be added in following commits.
Digidesign 002/003 family consists of:
* Agere FW802B for IEEE 1394 PHY layer
* PDI 1394L40 for IEEE 1394 LINK layer and IEC 61883 interface
* ALTERA ACEX EP1K50 for IEC 61883 layer and DSP controller
* ADSP-21065L for signal processing
[minor cleanup using skip_spaces() by tiwai]
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This device is based on DM1000E, and BeBoB version 1 firmware is
installed.
$ cat /proc/asound/cards
0 [Pro ]: BeBoB - Mbox 2 Pro
DIGIDESIGN Mbox 2 Pro (id:1, rev:1),
GUID 00a07e0100a90000 at fw1.0, S400
$ cat /proc/asound/Pro/firewire/firmware
Manufacturer: bridgeCo
Protocol Ver: 1
Build Ver: 0
GUID: 0x00A07E0100A90000
Model ID: 0x01
Model Rev: 1
Firmware Date: 20071031
Firmware Time: 034402
Firmware ID: 0xA9
Firmware Ver: 16777215
Base Addr: 0x20080000
Max Size: 1572864
Loader Date: 20051207
Loader Time: 205554
With this patch, ALSA BeBoB driver can start packet streaming to/from
this model, while as a default, internal multiplexer of this model is
not initialized and generates no sound even if the driver transfers
any packets with PCM samples. To hear any sounds from this model,
userspace applications should be developed to set parameters to the
internal multiplexer. You can see raw information in FFADO website:
http://subversion.ffado.org/wiki/AvcModels/DigiDesignMboxPro2
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This interface is designed for mixer/control application. By using this
interface, an application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some devices produced by Behringer/Mackie are based on OXFW970/971. This
commit adds support for them. Additionally, this commit changes the way to
name card with some information in config rom.
Ids of some Mackie(Loud) models are not identified, therefore this commit
applies name detection for these models.
The devices support capture/playback of PCM-samples and some of them
supports capture/playback of MIDI messages. These functionalities are
implemented by followed commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a support for capturing PCM samples.
When opposite PCM substream is already running, available sampling rate is
limited at current one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit renames 'firewire-speakers' to 'oxfw' to enhance support for
devices which based on OXFW970/971. A line for MODULE_ALIAS is added.
Additionally, to help for works in followed paches, some members
in private structure are renamed.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some developers test this driver, thus it's better to remove its
experimental state.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now snd-firewire-lib supports rawmidi in addition to PCM, thus we need
to give a proper dependency. For fixing and simplification, move the
selections of SND_PCM and SND_RAWMIDI into SND_FIREWIRE_LIB section.
Then each driver doesn't have to select them but only
SND_FIREWIRE_LIB.
Reported-by: Jim Davis <jim.epost@gmail.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to support some models which M-Audio produces
with DM1000 but its firmware is special. They are:
- Firewire 1814
- ProjectMix I/O
They have heavily customized firmware. The usual operations can't be applied to
them. For this reason, this commit adds a model specific member to 'struct
snd_bebob' and some model specific functions. Some parameters are write-only so
this commit also adds control interface for applications to set them.
M-Audio special firmware quirks:
- Just after powering on, they wait to download firmware. This state is
changed when receiving cue. Then bus reset is generated and the device is
recognized as a different model with the uploaded firmware.
- They don't respond against BridgeCo AV/C extension commands. So drivers
can't get their stream formations and so on.
- They do not start to transmit packets only by establishing connection but
also by receiving SIGNAL FORMAT command.
- After booting up, they often fail to send response against driver's request
due to mismatch of gap_count.
This module don't support to upload firmware.
Tested-by: Darren Anderson <darrena092@gmail.com> (ProjectMix I/O)
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to support some models which M-Audio produces
with DM1000/DM1000E with usual firmware. They are:
- Firewire 410
- Firewire AudioPhile
- Firewire Solo
- Ozonic
- NRV10
- FirewireLightBridge
According to a person who worked in BridgeCo, some models are produced with
'Pre-BeBoB'. This means that these products were released before BeBoB was
officially produced, and later BeBoB specification was formed. So these models
have some quirks.
M-Audio usual firmware quirks:
- Just after powering on, 'Firewire 410' waits to download firmware. This
state is changed when receiving cue. Then bus reset is generated and the
device is recognized as a different model with the uploaded firmware.
- 'Firewire Audiophile' also waits to download firmware but its
vendor id/model id is the same as the one after loading firmware.
- The information of channel mapping for MIDI conformant data channel is
invalid against BridgeCo specification.
This commit adds some codes for these quirks but don't support to upload
firmware.
This commit also adds specific operations to get metering information. The
metering information also includes status of clock synchronization if the model
supports to switch source of clock.
The specification of FirewireLightBridge is unknown. So in this time, normal
operations are applied for this model.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to support all of models which Focusrite
produces with DM1000/BeBoB. They are:
- Saffire
- Saffire LE
- SaffirePro 10 I/O
- SaffirePro 26 I/O
This commit adds Focusrite specific operations:
1. Get source of clock
2. Get/Set sampling frequency
3. Get metering information
The driver uses these functionalities to read/write specific address by async
transaction.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to support all of models which Yamaha produced
with DM1000/BeBoB. They are:
- GO44
- GO46
This commit adds Yamaha specific operations. To get source of clock, AV/C Audio
Subunit command is used.
I note that their appearances are similar to some models of TerraTec; 'Go44' is
similar to 'PHASE 24 FW' and 'GO46' is similar to 'PHASE X24 FW'. But their
combination of Audio/Music subunits is a bit different.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to support all of models which Terratec produced
with DM1000/BeBoB. They are:
- PHASE 24 FW
- PHASE X24 FW
- PHASE 88 Rack FW
- EWS MIC2
- EWS MIC4
- Aureon 7.1 Firewire
For Phase series, this commit adds a Terratec specific operation. To get source
of clock. AV/C Audio Subunit command is used.
For EWS series and Aureon, this module uses normal operations.
Tested-by: Maximilian Engelhardt <maxi@daemonizer.de> (PHASE 24 FW)
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This interface is designed for mixer/control application. By using hwdep
interface, the application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to capture/playback PCM samples.
When AMDTP stream is already running for PCM or the source of clock is not
internal, available sampling rate is limited at current one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to capture/playback MIDI messages.
When no AMDTP streams are running, this module starts AMDTP stream at current
sampling rate for MIDI substream.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This interface is designed for mixer/control application. To use hwdep
interface, the application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to capture/playback PCM samples.
When AMDTP stream is already running for PCM or the source of clock is not
internal, available sampling rate is limited at current one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a functionality to capture/playback MIDI messages.
When no AMDTP streams are running, this driver starts AMDTP stream for MIDI
stream at current sampling rate.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fireworks uses own command and response. This commit adds functionality to
transact and adds some commands required for sound card instance and kernel
streaming.
There are two ways to deliver substance of this transaction:
1.AV/C vendor dependent command for command/response
2.Async transaction to specific addresses for command/response
By way 1, I confirm AudioFire12 cannot correctly response to some commands with
firmware version 5.0 or later. This is also confirmed by FFADO. So this driver
implement way 2.
The address for response gives an issue. When this driver allocate own callback
function into the address, then no one can allocate its own callback function.
This situation is not good for applications in user-land. This issue is solved
in later commit.
I note there is a command to change the address for response if the device
supports. But this driver uses default value. So users should not execute this
command as long as hoping this driver works correctly.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a new driver for devices based on Fireworks. This driver
just creates/removes card instance according to callbacks.
Fireworks is a board module which Echo Audio produced. This module
consists of three chipsets:
- Communication chipset for IEEE1394 PHY/Link and IEC 61883-1/6
- DSP or/and FPGA for signal processing
- Flash Memory to store firmwares
Current supported devices:
- Mackie Onyx 400F/1200F
- Echo AudioFire12/8(until 2009 July)
- Echo AudioFire2/4/Pre8/8(since 2009 July)
- Echo Fireworks 8/HDMI
- Gibson Robot Interface pack/GoldTop
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At the moment, this driver supports only playback, while FFADO supports
(only) full-duplex devices. So, prevent conflicts by not claiming
devices that would be better handled by FFADO.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
As a start point for further development, this is an incomplete driver
for DICE devices:
- only playback (so no clock source except the bus clock)
- only 44.1 kHz
- no MIDI
- recovery after bus reset is slow
- hwdep device is created, but not actually implemented
Contains compilation fixes by Stefan Richter.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Add a MIDI driver for the Stanton FireWire DJ controllers.
Tested-by: Sean M. Pappalardo - D.J. Pegasus <spappalardo@mixxx.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Experiments have shown this driver to work now.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Tested-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds an experimental driver for the front and rear microphones of
the Apple iSight web camera.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a driver for two playback-only FireWire devices based on the OXFW970
chip.
v2: better AMDTP API abstraction; fix fw_unit leak; small fixes
v3: cache the iPCR value
v4: FireWave constraints; fix fw_device reference counting;
fix PCR caching; small changes and fixes
v5: volume/mute support; fix crashing due to pcm stop races
v6: fix build; one-channel volume for LaCie
v7: use signed values to make volume (range checks) work; fix function
block IDs for volume/mute; always use channel 0 for LaCie volume
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Jay Fenlason <fenlason@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
