The ndo_set_features callback function was improperly using an unsigned
int to save the current feature value for features such as NETIF_F_RXCSUM.
Since that feature is in the upper 32 bits of a 64 bit variable the
result was always 0 making it not possible to actually turn off the
hardware RX checksum support. Change the unsigned int type to the
netdev_features_t type in order to properly capture the current value
and perform the proper operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 278d240478 (net: fec: ptp: Enable PPS output based on ptp clock)
fec_enet_interrupt calls fec_ptp_check_pps_event unconditionally, which calls
into ptp_clock_event. If fep->ptp_clock is NULL, ptp_clock_event tries to
dereference the NULL pointer.
Since on i.MX53 fep->bufdesc_ex is not set, fec_ptp_init is never called,
and fep->ptp_clock is NULL, which reliably causes a kernel panic.
This patch adds a check for fep->ptp_clock == NULL in fec_enet_interrupt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After interface restart (eg: after link disconnection/reconnection), the bridge
function doesn't work anymore. This is due to the promiscuous mode being cleared
by the restart.
The mac-fcc already includes code to set the promiscuous mode back during the restart.
This patch adds the same handling to mac-fec and mac-scc.
Tested with bridge function on MPC885 with FEC.
Reported-by: Germain Montoies <germain.montoies@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
write_count and insert_count can wrap around, making > check invalid.
Fixes: 70b33fb0dd ("sfc: add support for
skb->xmit_more").
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following warning is shown when spinlock debug is enabled.
This occurs when enic_flow_may_expire timer function is running and
enic_stop is called on same CPU.
Fix this by using spink_lock_bh().
=================================
[ INFO: inconsistent lock state ]
3.17.0-netnext-05504-g59f35b8 #268 Not tainted
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
ifconfig/443 [HC0[0]:SC0[0]:HE1:SE1] takes:
(&(&enic->rfs_h.lock)->rlock){+.?...}, at:
enic_rfs_flw_tbl_free+0x34/0xd0 [enic]
{IN-SOFTIRQ-W} state was registered at:
[<ffffffff810a25af>] __lock_acquire+0x83f/0x21c0
[<ffffffff810a45f2>] lock_acquire+0xa2/0xd0
[<ffffffff814913fc>] _raw_spin_lock+0x3c/0x80
[<ffffffffa029c3d5>] enic_flow_may_expire+0x25/0x130[enic]
[<ffffffff810bcd07>] call_timer_fn+0x77/0x100
[<ffffffff810bd8e3>] run_timer_softirq+0x1e3/0x270
[<ffffffff8105f9ae>] __do_softirq+0x14e/0x280
[<ffffffff8105fdae>] irq_exit+0x8e/0xb0
[<ffffffff8103da0f>] smp_apic_timer_interrupt+0x3f/0x50
[<ffffffff81493742>] apic_timer_interrupt+0x72/0x80
[<ffffffff81018143>] default_idle+0x13/0x20
[<ffffffff81018a6a>] arch_cpu_idle+0xa/0x10
[<ffffffff81097676>] cpu_startup_entry+0x2c6/0x330
[<ffffffff8103b7ad>] start_secondary+0x21d/0x290
irq event stamp: 2997
hardirqs last enabled at (2997): [<ffffffff81491865>] _raw_spin_unlock_irqrestore+0x65/0x90
hardirqs last disabled at (2996): [<ffffffff814915e6>] _raw_spin_lock_irqsave+0x26/0x90
softirqs last enabled at (2968): [<ffffffff813b57a3>] dev_deactivate_many+0x213/0x260
softirqs last disabled at (2966): [<ffffffff813b5783>] dev_deactivate_many+0x1f3/0x260
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&enic->rfs_h.lock)->rlock);
<Interrupt>
lock(&(&enic->rfs_h.lock)->rlock);
*** DEADLOCK ***
Reported-by: Jan Stancek <jstancek@redhat.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch fixes a bug which causes the ax88179_178a driver to be
incapable of being added to a bond.
When I brought up the issue with the bonding maintainers, they indicated
that the real problem was with the NIC driver which must return zero for
success (of setting the MAC address). I see that several other NIC drivers
follow that pattern by either simply always returing zero, or by passing
through a negative (error) result while rewriting any positive return code
to zero. With that same philisophy applied to the ax88179_178a driver, it
allows it to work correctly with the bonding driver.
I believe this is suitable for queuing in -stable, as it's a small, simple,
and obvious fix that corrects a defect with no other known workaround.
This patch is against vanilla 3.17(.0).
Signed-off-by: Ian Morgan <imorgan@primordial.ca>
drivers/net/usb/ax88179_178a.c | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull slave-dmaengine updates from Vinod Koul:
"For dmaengine contributions we have:
- designware cleanup by Andy
- my series moving device_control users to dmanegine_xxx APIs for
later removal of device_control API
- minor fixes spread over drivers mainly mv_xor, pl330, mmp, imx-sdma
etc"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (60 commits)
serial: atmel: add missing dmaengine header
dmaengine: remove FSLDMA_EXTERNAL_START
dmaengine: freescale: remove FSLDMA_EXTERNAL_START control method
carma-fpga: move to fsl_dma_external_start()
carma-fpga: use dmaengine_xxx() API
dmaengine: freescale: add and export fsl_dma_external_start()
dmaengine: add dmaengine_prep_dma_sg() helper
video: mx3fb: use dmaengine_terminate_all() API
serial: sh-sci: use dmaengine_terminate_all() API
net: ks8842: use dmaengine_terminate_all() API
mtd: sh_flctl: use dmaengine_terminate_all() API
mtd: fsmc_nand: use dmaengine_terminate_all() API
V4L2: mx3_camer: use dmaengine_pause() API
dmaengine: coh901318: use dmaengine_terminate_all() API
pata_arasan_cf: use dmaengine_terminate_all() API
dmaengine: edma: check for echan->edesc => NULL in edma_dma_pause()
dmaengine: dw: export probe()/remove() and Co to users
dmaengine: dw: enable and disable controller when needed
dmaengine: dw: always export dw_dma_{en,dis}able
dmaengine: dw: introduce dw_dma_on() helper
...
been sitting in MST's tree during my vacation. I changed a function name
and made one trivial change, then they spent two days in linux-next.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JK6x
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio updates from Rusty Russell:
"One cc: stable commit, the rest are a series of minor cleanups which
have been sitting in MST's tree during my vacation. I changed a
function name and made one trivial change, then they spent two days in
linux-next"
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
virtio-rng: refactor probe error handling
virtio_scsi: drop scan callback
virtio_balloon: enable VQs early on restore
virtio_scsi: fix race on device removal
virito_scsi: use freezable WQ for events
virtio_net: enable VQs early on restore
virtio_console: enable VQs early on restore
virtio_scsi: enable VQs early on restore
virtio_blk: enable VQs early on restore
virtio_scsi: move kick event out from virtscsi_init
virtio_net: fix use after free on allocation failure
9p/trans_virtio: enable VQs early
virtio_console: enable VQs early
virtio_blk: enable VQs early
virtio_net: enable VQs early
virtio: add API to enable VQs early
virtio_net: minor cleanup
virtio-net: drop config_mutex
virtio_net: drop config_enable
virtio-blk: drop config_mutex
...
Pull networking fixes from David Miller:
1) Include fixes for netrom and dsa (Fabian Frederick and Florian
Fainelli)
2) Fix FIXED_PHY support in stmmac, from Giuseppe CAVALLARO.
3) Several SKB use after free fixes (vxlan, openvswitch, vxlan,
ip_tunnel, fou), from Li ROngQing.
4) fec driver PTP support fixes from Luwei Zhou and Nimrod Andy.
5) Use after free in virtio_net, from Michael S Tsirkin.
6) Fix flow mask handling for megaflows in openvswitch, from Pravin B
Shelar.
7) ISDN gigaset and capi bug fixes from Tilman Schmidt.
8) Fix route leak in ip_send_unicast_reply(), from Vasily Averin.
9) Fix two eBPF JIT bugs on x86, from Alexei Starovoitov.
10) TCP_SKB_CB() reorganization caused a few regressions, fixed by Cong
Wang and Eric Dumazet.
11) Don't overwrite end of SKB when parsing malformed sctp ASCONF
chunks, from Daniel Borkmann.
12) Don't call sock_kfree_s() with NULL pointers, this function also has
the side effect of adjusting the socket memory usage. From Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (90 commits)
bna: fix skb->truesize underestimation
net: dsa: add includes for ethtool and phy_fixed definitions
openvswitch: Set flow-key members.
netrom: use linux/uaccess.h
dsa: Fix conversion from host device to mii bus
tipc: fix bug in bundled buffer reception
ipv6: introduce tcp_v6_iif()
sfc: add support for skb->xmit_more
r8152: return -EBUSY for runtime suspend
ipv4: fix a potential use after free in fou.c
ipv4: fix a potential use after free in ip_tunnel_core.c
hyperv: Add handling of IP header with option field in netvsc_set_hash()
openvswitch: Create right mask with disabled megaflows
vxlan: fix a free after use
openvswitch: fix a use after free
ipv4: dst_entry leak in ip_send_unicast_reply()
ipv4: clean up cookie_v4_check()
ipv4: share tcp_v4_save_options() with cookie_v4_check()
ipv4: call __ip_options_echo() in cookie_v4_check()
atm: simplify lanai.c by using module_pci_driver
...
skb->truesize is not meant to be tracking amount of used bytes
in an skb, but amount of reserved/consumed bytes in memory.
For instance, if we use a single byte in last page fragment,
we have to account the full size of the fragment.
skb->truesize can be very different from skb->len, that has
a very specific safety purpose.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b4d2394d01 ("dsa: Replace mii_bus with a generic host device")
replaces mii_bus with a generic host_dev, and introduces
dsa_host_dev_to_mii_bus() to support conversion from host_dev to mii_bus.
However, in some cases it uses to_mii_bus to perform that conversion.
Since host_dev is not the phy bus device but typically a platform device,
this fails and results in a crash with the affected drivers.
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<ffffffff81781d35>] __mutex_lock_slowpath+0x75/0x100
PGD 406783067 PUD 406784067 PMD 0
Oops: 0002 [#1] SMP
...
Call Trace:
[<ffffffff810a538b>] ? pick_next_task_fair+0x61b/0x880
[<ffffffff81781de3>] mutex_lock+0x23/0x37
[<ffffffff81533244>] mdiobus_read+0x34/0x60
[<ffffffff8153b95a>] __mv88e6xxx_reg_read+0x8a/0xa0
[<ffffffff8153b9bc>] mv88e6xxx_reg_read+0x4c/0xa0
Fixes: b4d2394d01 ("dsa: Replace mii_bus with a generic host device")
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't ring the doorbell, and don't do PIO. This will also prevent
TX Push, because there will be more than one buffer waiting when
the doorbell is rung.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove calling cancel_delayed_work_sync() for runtime suspend,
because it would cause dead lock. Instead, return -EBUSY to
avoid the device enters suspending if the net is running and
the delayed work is pending or running. The delayed work would
try to wake up the device later, so the suspending is not
necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case that the IP header has optional field at the end, this patch will
get the port numbers after that field, and compute the hash. The general
parser skb_flow_dissect() is used here.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pskb_may_pull maybe change skb->data and make eth pointer oboslete,
so eth needs to reload
Fixes: 91269e390d ("vxlan: using pskb_may_pull as early as possible")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for vfinfo is not sufficient because it does not protect
against specifying vf that is outside of sriov_num_vfs range.
All of the ndo functions have a check for it except for
ixgbevf_ndo_set_spoofcheck().
The following patch is all we need to protect against this panic:
ip link set p96p1 vf 0 spoofchk off
BUG: unable to handle kernel NULL pointer dereference at 0000000000000052
IP: [<ffffffffa044a1c1>]
ixgbe_ndo_set_vf_spoofchk+0x51/0x150 [ixgbe]
Reported-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Acked-by: Thierry Herbelot <thierry.herbelot@6wind.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Compiling with CONFIG_FM10K=y and VXLAN=m resulting in linking error:
drivers/built-in.o: In function `fm10k_open':
(.text+0x1f9d7a): undefined reference to `vxlan_get_rx_port'
make: *** [vmlinux] Error 1
The fix follows the same strategy as I40E.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After grabbing the mailbox lock and detecting an error, the lock must be
released before the error code can be returned.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the flag to fetch the host state before kicking off the service task
that reads the host state when bringing the interface back up.
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
pskb_may_pull should be used to check if skb->data has enough space,
skb->len can not ensure that.
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when netif_rx() is done, the netif_rx handled skb maybe be freed,
and should not be used.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each Rx frame the eTSEC writes its FCS (Frame Check Sequence)
to the Rx buffer.
The eTSEC h/w manual states in the "Receive Buffer Descriptor Field
Descriptions" table:
"Data length is the number of octets written by the eTSEC into this BD's
data buffer if L is cleared (the value is equal to MRBLR), or, if L is
set, the length of the frame including *CRC*, FCB (if RCTRL[PRSDEP > 00),
preamble (if MACCFG2[PreAmRxEn]=1), time stamp (if RCTRL[TS] = 1) and
any padding (RCTRL[PAL])."
Though the FCS bytes are removed by the driver before passing the skb
to the net stack, the Rx buffer size computation does not currently
take into account the FCS bytes (4 bytes).
Because the Rx buffer size is multiple of 512 bytes, leaving out the
FCS is not a problem for the default MTU of 1500, as the Rx buffer size
is 1536 in this case. However, for custom MTUs, where the difference
between the MTU size and the Rx buffer size is less, this can be a
problem as the computed Rx buffer size won't be enough to accomodate
the FCS for a received frame that is big enough (close to MTU size).
In such case the received frame is considered to be incomplete (L flag
not set in the RxBD status) and silently dropped.
Note that the driver does not currently support S/G on Rx, so it has to
compute its Rx buffer size based on the MTU of the device.
Reported-by: Kristian Otnes <kotnes@cisco.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 0b725a2ca6
net: Remove ndo_xmit_flush netdev operation, use signalling instead.
added code that looks at skb->xmit_more after the skb has
been put in TX VQ. Since some paths process the ring and free the skb
immediately, this can cause use after free.
Fix by storing xmit_more in a local variable.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iMX6SX IEEE 1588 module has one hw issue in capturing the ATVR register.
The current SW flow is:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
ts_counter_ns = ENET0->ATVR;
The ATVR value is not expected value that cause LinuxPTP stack cannot be convergent.
ENET Block Guide/ Chapter for the iMX6SX (PELE) address the issue:
After set ENET_ATCR[Capture], there need some time cycles before the counter
value is capture in the register clock domain. The wait-time-cycles is at least
6 clock cycles of the slower clock between the register clock and the 1588 clock.
So need something like:
ENET0->ATCR |= ENET_ATCR_CAPTURE_MASK;
wait();
ts_counter_ns = ENET0->ATVR;
For iMX6SX, the 1588 ts_clk is fixed to 25Mhz, register clock is 66Mhz, so the
wait-time-cycles must be greater than 240ns (40ns * 6). The patch add 1us delay
before cpu read ATVR register.
Changes V2:
Modify the commit/comments log to describe the issue clearly.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_gso_check which a device can define to indicate whether is
is capable of doing GSO on a packet. This funciton would be called from
the stack to determine whether software GSO is needed to be done. A
driver should populate this function if it advertises GSO types for
which there are combinations that it wouldn't be able to handle. For
instance a device that performs UDP tunneling might only implement
support for transparent Ethernet bridging type of inner packets
or might have limitations on lengths of inner headers.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The drivers should use dmaengine_terminate_all() API instead of
accessing the device_control which will be deprecated soon
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
this patch is to fix the stmmac data compatibilities for
all the SoCs inside the platform file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
cxgb4 ipv6 does not guard against ipv6 being disabled, or the standard
ipv6 module vs inbuilt tri-state issue. This was fixed for cxgb4i & iw_cxgb4
but missed for cxgb4.
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
cxgb4 already handles CLIP updates from a previous changeset for iw_cxgb4,
there is no need to have this functionality in cxgb4i. Remove duplicated code
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
virtio spec requires drivers to set DRIVER_OK before using VQs.
This is set automatically after restore returns, virtio net violated this
rule by using receive VQs within restore.
To fix, call virtio_device_ready before using VQs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
In the extremely unlikely event that driver initialization fails after
RX buffers are added, virtio net frees RX buffers while VQs are
still active, potentially causing device to use a freed buffer.
To fix, reset device first - same as we do on device removal.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
virtio spec requires drivers to set DRIVER_OK before using VQs.
This is set automatically after probe returns, virtio net violated this
rule by using receive VQs within probe.
To fix, call virtio_device_ready before using VQs.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
goto done;
done:
return;
is ugly, it was put there to make diff review easier.
replace by open-coded return.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
config_mutex served two purposes: prevent multiple concurrent config
change handlers, and synchronize access to config_enable flag.
Since commit dbf2576e37
workqueue: make all workqueues non-reentrant
all workqueues are non-reentrant, and config_enable
is now gone.
Get rid of the unnecessary lock.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Now that virtio core ensures config changes don't arrive during probing,
drop config_enable flag in virtio net.
On removal, flush is now sufficient to guarantee that no change work is
queued.
This help simplify the driver, and will allow setting DRIVER_OK earlier
without losing config change notifications.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
o Number of arguments taken by destroy tx command is three
instead of two.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Initially we were programming maximum number of arguments.
Instead we should program number of arguments required in
a command.
o Maximum number of arguments for 82xx adapter is four. Fix it
for GET_ESWITCH_STATS command.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use t4_fw_upgrade instead of t4_load_fw to write firmware into FLASH, since
t4_load_fw doesn't co-ordinate with the firmware and the adapter can get hosed
enough to require a power cycle of the system.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to review the whole glue logic adopted on STi SoCs that
was bugged.
In the old glue-logic there was a lot of confusion when setup the
retiming especially for STiD127 where, for example, the bits 6 and 7
(in the GMAC control register) have a different meaning of what is
used for STiH4xx SoCs. So we cannot adopt the same glue for all these
SoCs.
Moreover, GiGa on STiD127 didn't work and, for all the SoCs, the RGMII
couldn't run when the speed was 10Mbps (because the clock was not properly
managed).
Note that the phy clock needs to be provided by the platform as well as
documented in the related binding file (updated as consequence).
The old code supported too many configurations never adopted and validated.
This made the code very complex to maintain and debug in case of issues.
The patch simplifies all the configurations as commented in the tables
inside the file and obviously it has been tested on all the boards
based on the SoCs mentioned.
With this patch, the dwmac-sti is also ready to support new configurations that
will be available on next SoC generations.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the missing compatibility to the STiH407 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On several STi platforms: e.g. stihxxx-b2120 an Ethernet switch is
embedded and connected to the stmmac via RGMII mode. So this is managed
by using the FIXED_PHY. In that case, the support in the platform needs
to be fixed to allow the stmmac to dialog with the switch via fixed-link
by using phy_bus_name property.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tag_protocol is now an enum, so drivers have to check against it.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added link_state function pointer to the xgene__mac_ops structure
- Moved ring manager (pdata->rm) assignment to xgene_enet_setup_ops
- Removed unused variable (pdata->phy_addr) and macro (FULL_DUPLEX)
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove all the child devices from the system to make sure that re-insert of
cpsw module doesn't fail on child device populated by of_platform_populate().
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
memories allocated with devm_* apis must not be freed with kfree apis,
so removing the kfree calls
Fixes: e194312854 ('drivers: net: davinci_cpdma: Convert kzalloc() to devm_kzalloc().')
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ring TX doorbell only if xmit_more is not set or the queue is stopped.
Suggested-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FEC ptp timer has 4 channel compare/trigger function. It can be used to
enable pps output.
The pulse would be ouput high exactly on N second. The pulse ouput high
on compare event mode is used to produce pulse per second. The pulse
width would be one cycle based on ptp timer clock source.Since 31-bit
ptp hardware timer is used, the timer will wrap more than 2 seconds. We
need to reload the compare compare event about every 1 second.
Signed-off-by: Luwei Zhou <b45643@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC IP supports hardware adjustment for ptp timer. Refer to the description of
ENET_ATCOR and ENET_ATINC registers in the spec about the hardware adjustment. This
patch uses hardware support to adjust the ptp offset and frequency on the slave side.
Signed-off-by: Luwei Zhou <b45643@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Fugang Duan <b38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ptp switches from software adjustment to hardware ajustment, linux ptp can't converge.
It is caused by the IP limit. Hardware adjustment logcial have issue when ptp counter
runs over 0x80000000(31 bit counter). The internal IP reference manual already remove 32bit
free-running count support. This patch replace the 32-bit PTP timer with 31-bit.
Signed-off-by: Luwei Zhou <b45643@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change adds support for skb->xmit_more based on the changes that were
made to igb to support the feature. The main changes are moving up the
check for maybe_stop_tx so that we can check netif_xmit_stopped to determine
if we must write the tail because we can add no further buffers.
Acked-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reproduce:
make ARCH=arm C=1 2>fec.txt drivers/net/ethernet/freescale/fec_main.o
cat fec.txt
sparse warnings:
drivers/net/ethernet/freescale/fec_main.c:2916:12: warning: context imbalance
in 'fec_set_features' - different lock contexts for basic block
Christopher Li suggest to change as below:
if (need_lock) {
lock();
do_something_real();
unlock();
} else {
do_something_real();
}
Reported-by: Fabio Estevam <festevam@gmail.com>
Suggested-by: Christopher Li <sparse@chrisli.org>
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bug: Unable to send and receive Ethernet packets with Micrel PHY.
Affected devices:
KSZ8031RNL (commercial temp)
KSZ8031RNLI (industrial temp)
Description:
PHY device is correctly detected during probe.
PHY power-up default is 25MHz crystal clock input
and output 50MHz RMII clock to MAC.
Reconfiguration of PHY to input 50MHz RMII clock from MAC
causes PHY to become unresponsive if clock source is changed
after Operation Mode Strap Override (OMSO) register setup.
Cause:
Long lead times on parts where clock setup match circuit design
forces the usage of similar parts with wrong default setup.
Solution:
Swapped KSZ8031 register setup and added phy_write return code validation.
Tested with Freescale i.MX28 Fast Ethernet Controler (fec).
Signed-off-by: Bruno Thomsen <bth@kamstrup.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull kbuild changes from Michal Marek:
- fix for handling dependencies of *-objs targets by Masahiro Yamada
- lots of cleanups in the kbuild machinery, also by Masahiro
- fixes for the kconfig build to use an UTF-8 capable ncurses library
if possible and to build on not-so-standard installs
- some more minor fixes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Do not reference *-n variables in the Makefile
kbuild: simplify build, clean, modbuiltin shorthands
kbuild: arm: Do not define "comma" twice
kbuild: remove obj-n and lib-n handling
kbuild: remove unnecessary variable initializaions
kbuild: remove unnecessary "obj- := dummy.o" trick
kbuild: handle C=... and M=... after entering into build directory
kbuild: use $(Q) for sub-make target
kbuild: fake the "Entering directory ..." message more simply
kconfig/lxdialog: get ncurses CFLAGS with pkg-config
kconfig: nconfig: fix multi-byte UTF handling
kconfig: lxdialog: fix spelling
kbuild: Make scripts executable
kbuild: remove redundant clean-files from scripts/kconfig/Makefile
kbuild: refactor script/kconfig/Makefile
kbuild: handle the dependency of multi-objs hostprogs appropriately
kbuild: handle multi-objs dependency appropriately
Pull vfs updates from Al Viro:
"The big thing in this pile is Eric's unmount-on-rmdir series; we
finally have everything we need for that. The final piece of prereqs
is delayed mntput() - now filesystem shutdown always happens on
shallow stack.
Other than that, we have several new primitives for iov_iter (Matt
Wilcox, culled from his XIP-related series) pushing the conversion to
->read_iter()/ ->write_iter() a bit more, a bunch of fs/dcache.c
cleanups and fixes (including the external name refcounting, which
gives consistent behaviour of d_move() wrt procfs symlinks for long
and short names alike) and assorted cleanups and fixes all over the
place.
This is just the first pile; there's a lot of stuff from various
people that ought to go in this window. Starting with
unionmount/overlayfs mess... ;-/"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (60 commits)
fs/file_table.c: Update alloc_file() comment
vfs: Deduplicate code shared by xattr system calls operating on paths
reiserfs: remove pointless forward declaration of struct nameidata
don't need that forward declaration of struct nameidata in dcache.h anymore
take dname_external() into fs/dcache.c
let path_init() failures treated the same way as subsequent link_path_walk()
fix misuses of f_count() in ppp and netlink
ncpfs: use list_for_each_entry() for d_subdirs walk
vfs: move getname() from callers to do_mount()
gfs2_atomic_open(): skip lookups on hashed dentry
[infiniband] remove pointless assignments
gadgetfs: saner API for gadgetfs_create_file()
f_fs: saner API for ffs_sb_create_file()
jfs: don't hash direct inode
[s390] remove pointless assignment of ->f_op in vmlogrdr ->open()
ecryptfs: ->f_op is never NULL
android: ->f_op is never NULL
nouveau: __iomem misannotations
missing annotation in fs/file.c
fs: namespace: suppress 'may be used uninitialized' warnings
...
Pull networking fixes from David Miller:
"This set fixes a bunch of fallout from the changes that went in during
this merge window, particularly:
- Fix fsl_pq_mdio (Claudiu Manoil) and fm10k (Pranith Kumar) build
failures.
- Several networking drivers do atomic_set() on page counts where
that's not exactly legal. From Eric Dumazet.
- Make __skb_flow_get_ports() work cleanly with unaligned data, from
Alexander Duyck.
- Fix some kernel-doc buglets in rfkill and netlabel, from Fabian
Frederick.
- Unbalanced enable_irq_wake usage in bcmgenet and systemport
drivers, from Florian Fainelli.
- pxa168_eth needs to depend on HAS_DMA, from Geert Uytterhoeven.
- Multi-dequeue in the qdisc layer severely bypasses the fairness
limits the previous code used to enforce, reintroduce in a way that
at the same time doesn't compromise bulk dequeue opportunities.
From Jesper Dangaard Brouer.
- macvlan receive path unnecessarily hops through a softirq by using
netif_rx() instead of netif_receive_skb(). From Jason Baron"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (51 commits)
net: systemport: avoid unbalanced enable_irq_wake calls
net: bcmgenet: avoid unbalanced enable_irq_wake calls
net: bcmgenet: fix off-by-one in incrementing read pointer
net: fix races in page->_count manipulation
mlx4: fix race accessing page->_count
ixgbe: fix race accessing page->_count
igb: fix race accessing page->_count
fm10k: fix race accessing page->_count
net/phy: micrel: Add clock support for KSZ8021/KSZ8031
flow-dissector: Fix alignment issue in __skb_flow_get_ports
net: filter: fix the comments
Documentation: replace __sk_run_filter with __bpf_prog_run
macvlan: optimize the receive path
macvlan: pass 'bool' type to macvlan_count_rx()
drivers: net: xgene: Add 10GbE ethtool support
drivers: net: xgene: Add 10GbE support
drivers: net: xgene: Preparing for adding 10GbE support
dtb: Add 10GbE node to APM X-Gene SoC device tree
Documentation: dts: Update section header for APM X-Gene
MAINTAINERS: Update APM X-Gene section
...
Pull sparc updates from David Miller:
1) Move to 4-level page tables on sparc64 and support up to 53-bits of
physical addressing. Kernel static image BSS size reduced by
several megabytes.
2) M6/M7 cpu support, from Allan Pais.
3) Move to sparse IRQs, handle hypervisor TLB call errors more
gracefully, and add T5 perf_event support. From Bob Picco.
4) Recognize cdroms and compute geometry from capacity in virtual disk
driver, also from Allan Pais.
5) Fix memset() return value on sparc32, from Andreas Larsson.
6) Respect gfp flags in dma_alloc_coherent on sparc32, from Daniel
Hellstrom.
7) Fix handling of compound pages in virtual disk driver, from Dwight
Engen.
8) Fix lockdep warnings in LDC layer by moving IRQ requesting to
ldc_alloc() from ldc_bind().
9) Increase boot string length to 1024 bytes, from Dave Kleikamp.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc: (31 commits)
sparc64: Fix lockdep warnings on reboot on Ultra-5
sparc64: Increase size of boot string to 1024 bytes
sparc64: Kill unnecessary tables and increase MAX_BANKS.
sparc64: sparse irq
sparc64: Adjust vmalloc region size based upon available virtual address bits.
sparc64: Increase MAX_PHYS_ADDRESS_BITS to 53.
sparc64: Use kernel page tables for vmemmap.
sparc64: Fix physical memory management regressions with large max_phys_bits.
sparc64: Adjust KTSB assembler to support larger physical addresses.
sparc64: Define VA hole at run time, rather than at compile time.
sparc64: Switch to 4-level page tables.
sparc64: Fix reversed start/end in flush_tlb_kernel_range()
sparc64: Add vio_set_intr() to enable/disable Rx interrupts
vio: fix reuse of vio_dring slot
sunvdc: limit each sg segment to a page
sunvdc: compute vdisk geometry from capacity
sunvdc: add cdrom and v1.1 protocol support
sparc: VIO protocol version 1.6
sparc64: Fix hibernation code refrence to PAGE_OFFSET.
sparc64: Move request_irq() from ldc_bind() to ldc_alloc()
...
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJUNonmAAoJEFxbo/MsZsTRHAQH/inCjpCT+pkvTB0YAVfVvgMI
gUogT8G+iB2MuCNpMffGIt8TAVXwcVtnOLH9ABH3IBVehzgipIbIiVEM9YhjrYvU
1rgIKBpmZqSpjDHoIHpdHeCH67cVnRzA/PyoxZWLxPNmQ0t6bNf9yeAcCXK9PfUc
7EAblUDmPGSx9x/EUnOKNNaZSEiUJZHDBXbMBLllk1+5H1vfKnpFCRGMG0IrfI44
KVP2NX9Gfa05edMZYtH887FYyjFe2KNV6LJvE7+w7h2Dy0yIzf7y86t0l4n8gETb
plvEUJ/lu9RYzTiZY/RxgBFYVTV59EqT45brSUtoe2Jcp8GSwiHslTHdfyFBwSo=
=gw4d
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen updates from David Vrabel:
"Features and fixes:
- Add pvscsi frontend and backend drivers.
- Remove _PAGE_IOMAP PTE flag, freeing it for alternate uses.
- Try and keep memory contiguous during PV memory setup (reduces
SWIOTLB usage).
- Allow front/back drivers to use threaded irqs.
- Support large initrds in PV guests.
- Fix PVH guests in preparation for Xen 4.5"
* tag 'stable/for-linus-3.18-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (22 commits)
xen: remove DEFINE_XENBUS_DRIVER() macro
xen/xenbus: Remove BUG_ON() when error string trucated
xen/xenbus: Correct the comments for xenbus_grant_ring()
x86/xen: Set EFER.NX and EFER.SCE in PVH guests
xen: eliminate scalability issues from initrd handling
xen: sync some headers with xen tree
xen: make pvscsi frontend dependant on xenbus frontend
arm{,64}/xen: Remove "EXPERIMENTAL" in the description of the Xen options
xen-scsifront: don't deadlock if the ring becomes full
x86: remove the Xen-specific _PAGE_IOMAP PTE flag
x86/xen: do not use _PAGE_IOMAP PTE flag for I/O mappings
x86: skip check for spurious faults for non-present faults
xen/efi: Directly include needed headers
xen-scsiback: clean up a type issue in scsiback_make_tpg()
xen-scsifront: use GFP_ATOMIC under spin_lock
MAINTAINERS: Add xen pvscsi maintainer
xen-scsiback: Add Xen PV SCSI backend driver
xen-scsifront: Add Xen PV SCSI frontend driver
xen: Add Xen pvSCSI protocol description
xen/events: support threaded irqs for interdomain event channels
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Hhee
-----END PGP SIGNATURE-----
Merge tag 'locks-v3.18-1' of git://git.samba.org/jlayton/linux
Pull file locking related changes from Jeff Layton:
"This release is a little more busy for file locking changes than the
last:
- a set of patches from Kinglong Mee to fix the lockowner handling in
knfsd
- a pile of cleanups to the internal file lease API. This should get
us a bit closer to allowing for setlease methods that can block.
There are some dependencies between mine and Bruce's trees this cycle,
and I based my tree on top of the requisite patches in Bruce's tree"
* tag 'locks-v3.18-1' of git://git.samba.org/jlayton/linux: (26 commits)
locks: fix fcntl_setlease/getlease return when !CONFIG_FILE_LOCKING
locks: flock_make_lock should return a struct file_lock (or PTR_ERR)
locks: set fl_owner for leases to filp instead of current->files
locks: give lm_break a return value
locks: __break_lease cleanup in preparation of allowing direct removal of leases
locks: remove i_have_this_lease check from __break_lease
locks: move freeing of leases outside of i_lock
locks: move i_lock acquisition into generic_*_lease handlers
locks: define a lm_setup handler for leases
locks: plumb a "priv" pointer into the setlease routines
nfsd: don't keep a pointer to the lease in nfs4_file
locks: clean up vfs_setlease kerneldoc comments
locks: generic_delete_lease doesn't need a file_lock at all
nfsd: fix potential lease memory leak in nfs4_setlease
locks: close potential race in lease_get_mtime
security: make security_file_set_fowner, f_setown and __f_setown void return
locks: consolidate "nolease" routines
locks: remove lock_may_read and lock_may_write
lockd: rip out deferred lock handling from testlock codepath
NFSD: Get reference of lockowner when coping file_lock
...
Multiple enable_irq_wake() calls will keep increasing the IRQ
wake_depth, which ultimately leads to the following types of
situation:
1) enable Wake-on-LAN interrupt w/o password
2) enable Wake-on-LAN interrupt w/ password
3) enable Wake-on-LAN interrupt w/o password
4) disable Wake-on-LAN interrupt
After step 4), SYSTEMPORT would always wake-up the system no matter what
wake-up device we use, which is not what we want. Fix this by making
sure there are no unbalanced enable_irq_wake() calls.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multiple enable_irq_wake() calls will keep increasing the IRQ
wake_depth, which ultimately leads to the following types of
situation:
1) enable Wake-on-LAN interrupt w/o password
2) enable Wake-on-LAN interrupt w/ password
3) enable Wake-on-LAN interrupt w/o password
4) disable Wake-on-LAN interrupt
After step 4), GENET would always wake-up the system no matter what
wake-up device we use, which is not what we want. Fix this by making
sure there are no unbalanced enable_irq_wake() calls.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b629be5c83 ("net: bcmgenet: check
harder for out of memory conditions") moved the increment of the local
read pointer *before* reading from the hardware descriptor using
dmadesc_get_length_status(), which creates an off-by-one situation.
Fix this by moving again the read_ptr increment after we have read the
hardware descriptor to get both the control block and the read pointer
back in sync.
Fixes: b629be5c83 ("net: bcmgenet: check harder for out of memory conditions")
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is illegal to use atomic_set(&page->_count, ...) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is illegal to use atomic_set(&page->_count, 2) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is illegal to use atomic_set(&page->_count, 2) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is illegal to use atomic_set(&page->_count, 2) even if we 'own'
the page. Other entities in the kernel need to use get_page_unless_zero()
to get a reference to the page before testing page properties, so we could
loose a refcount increment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ8021 and KSZ8031 support RMII reference input clocks of 25MHz
and 50MHz. Both PHYs differ in the default frequency they expect
after reset. If this differs from the actual input clock, then
register 0x1f bit 7 must be changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_rx() call on the fast path of macvlan_handle_frame() appears to
be there to ensure that we properly throttle incoming packets. However, it
would appear as though the proper throttling is already in place for all
possible ingress paths, and that the call is redundant. If packets are arriving
from the physical NIC, we've already throttled them by this point. Otherwise,
if they are coming via macvlan_queue_xmit(), it calls either
'dev_forward_skb()', which ends up calling netif_rx_internal(), or else in
the broadcast case, we are throttling via macvlan_broadcast_enqueue().
The test results below are from off the box to an lxc instance running macvlan.
Once the tranactions/sec stop increasing, the cpu idle time has gone to 0.
Results are from a quad core Intel E3-1270 V2@3.50GHz box with bnx2x 10G card.
for i in {10,100,200,300,400,500};
do super_netperf $i -H $ip -t TCP_RR; done
Average of 5 runs.
trans/sec trans/sec
(3.17-rc7-net-next) (3.17-rc7-net-next + this patch)
---------- ----------
208101 211534 (+1.6%)
839493 850162 (+1.3%)
845071 844053 (-.12%)
816330 819623 (+.4%)
778700 789938 (+1.4%)
735984 754408 (+2.5%)
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass last argument to macvlan_count_rx() as the correct bool type.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Added 10GbE support
- Removed unused macros/variables
- Moved mac_init call to the end of hardware init
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Rearranged code to pave the way for adding 10GbE support
- Added mac_ops structure containing function pointers for mac specific functions
- Added port_ops structure containing function pointers for port specific functions
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-10-09
Please pull this batch of fixes intended for the 3.18 stream!
Andrea Merello makes rtl818x_pci use a more reasonable transmission
rate for HW generated frames.
Fabian Frederick tweaks some kernel-doc bits to avoid warnings.
Larry Finger corrects a possible unaligned access in the rtlwifi code.
Marek Puzyniak avoids a kernel panic in ath9k_hw_reset.
Sujith Manoharan goes for the hat trick -- he fixes a smatch warning
in the shared ath code, he fixes a crash in ath9k, and he corrects
a sequence number assignment problem in ath9k too.
For ease of merging, I pulled the last bits of the wireless tree as well...
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing revealed that the local variable mc_filter was dimensioned
incorrectly for all possible configurations and get_mac_addr should
have been set_mac_addr (a typo). Make sure mc_filter is dimensioned
to 8 32-bit unsigned longs - the largest size of the Synopsys
multicast filter register set.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `rxq_deinit':
pxa168_eth.c:(.text+0x2a2f2e): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `txq_reclaim':
pxa168_eth.c:(.text+0x2a3044): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `txq_deinit':
pxa168_eth.c:(.text+0x2a310a): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `txq_init':
pxa168_eth.c:(.text+0x2a3226): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `rxq_init':
pxa168_eth.c:(.text+0x2a32d4): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `init_hash_table':
pxa168_eth.c:(.text+0x2a3354): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `rxq_refill':
pxa168_eth.c:(.text+0x2a345a): undefined reference to `dma_map_single'
drivers/built-in.o: In function `rxq_process':
pxa168_eth.c:(.text+0x2a39cc): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `pxa168_eth_remove':
pxa168_eth.c:(.text+0x2a3b84): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `pxa168_eth_start_xmit':
pxa168_eth.c:(.text+0x2a3e8a): undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest linus git tip (3.18-rc1) fails with the following build failure. Fix
this by making PTP support explicit for fm10k driver.
rivers/built-in.o: In function `fm10k_ptp_register':
(.text+0x12e760): undefined reference to `ptp_clock_registER'
drivers/built-in.o: In function `fm10k_ptp_unregister':
(.text+0x12e7dc): undefined reference to `ptp_clock_unregister'
Makefile:930: recipe for target 'vmlinux' failed
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
[linux-devel:devel-hourly-2014100909 3763/3915] drivers/net/ethernet/freescale/fs_enet/mac-scc.c:119:32: error: 'SCCE_ENET_TXF' undeclared
Due to patch d43a396 net: fs_enet: Add NAPI TX, it appears that some target
compilations are broken.
This is due to the fact that unlike the FEC, the SCC and FCC don't have a TXF
event (complete Frame transmitted) but only TXB (buffer transmitted).
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the mutex to avoid the settings are interrupted by other ones.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add usb_autopm_xxx for rtl8152_get_settings() ,and remove
usb_autopm_xxx from read_mii_word() and write_mii_word().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call t4_wait_dev_ready() before attempting to read the PL_WHOAMI register
(to determine which function we have been attached to). This prevents us from
failing on that read if it comes right after a RESET.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 40G support for cxgb4vf driver. ethtool speed values are just numbers of
megabits and there is no SPEED_40000 in ethtool speed values. To be consistent,
use integer constants directly for all speeds.
Use is_x_10g_port()("is 10Gb/s or higher") in cfg_queues() instead of
is_10g_port() ("is exactly 10Gb/s"). Else we will end up using a single
"Queue Set" on 40Gb/s adapters.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the lso length for T5 adapter and fix PIDX_T5 macro
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
we used to check for "nobody else could start doing anything with
that opened file" by checking that refcount was 2 or less - one
for descriptor table and one we'd acquired in fget() on the way to
wherever we are. That was race-prone (somebody else might have
had a reference to descriptor table and do fget() just as we'd
been checking) and it had become flat-out incorrect back when
we switched to fget_light() on those codepaths - unlike fget(),
it doesn't grab an extra reference unless the descriptor table
is shared. The same change allowed a race-free check, though -
we are safe exactly when refcount is less than 2.
It was a long time ago; pre-2.6.12 for ioctl() (the codepath leading
to ppp one) and 2.6.17 for sendmsg() (netlink one). OTOH,
netlink hadn't grown that check until 3.9 and ppp used to live
in drivers/net, not drivers/net/ppp until 3.1. The bug existed
well before that, though, and the same fix used to apply in old
location of file.
Cc: stable@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Replace PPC specific eieio() with arch independent wmb()
for other architectures, i.e. ARM.
The eieio() macro is not defined on ARM and generates
build error.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use arch independent code to replace the powerpc dependent
spin_event_timeout() from gfar_halt_nodisable().
Added GRS/GTS read accessors to clean-up the implementation
of gfar_halt_nodisable().
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the 32-bit memory access that is not endian safe,
i.e. not giving the desired byte layout for a LE CPU:
tempval = *((u32 *) (tmpbuf + 4)), where 'char tmpbuf[]'.
Get rid of rendundant local vars (tmpbuf[] and idx) and
forced casts. Cleanup comments.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This excludes the PPC specific instructions for PPC based SoC
(MPC85xx family) version identification from ARM builds.
The PPC specific macro mfspr() from asm/reg.h is not defined
by the ARM architecture.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include linux/of_address.h for of_iomap() and linux/of_irq.h
for irq_of_parse_and_map().
This wasn't an issue for PPC, because these were implicitly
included from asm/prom.h (via linux/of.h) for PPC builds only.
ARM builds need these includes explicitly.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
spin_event_timeout() is PPC dependent, use an arch independent
equivalent instead.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in_be32()/out_be32() are not defined by ARM.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UCC specific code included in fsl_pq_mdio.c (with
function calls from asm/ucc.h) is already guarded
by these config options, so this ARM build fix only
provides consistency with the rest UCC specific code.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Most notable changes in here:
1) By far the biggest accomplishment, thanks to a large range of
contributors, is the addition of multi-send for transmit. This is
the result of discussions back in Chicago, and the hard work of
several individuals.
Now, when the ->ndo_start_xmit() method of a driver sees
skb->xmit_more as true, it can choose to defer the doorbell
telling the driver to start processing the new TX queue entires.
skb->xmit_more means that the generic networking is guaranteed to
call the driver immediately with another SKB to send.
There is logic added to the qdisc layer to dequeue multiple
packets at a time, and the handling mis-predicted offloads in
software is now done with no locks held.
Finally, pktgen is extended to have a "burst" parameter that can
be used to test a multi-send implementation.
Several drivers have xmit_more support: i40e, igb, ixgbe, mlx4,
virtio_net
Adding support is almost trivial, so export more drivers to
support this optimization soon.
I want to thank, in no particular or implied order, Jesper
Dangaard Brouer, Eric Dumazet, Alexander Duyck, Tom Herbert, Jamal
Hadi Salim, John Fastabend, Florian Westphal, Daniel Borkmann,
David Tat, Hannes Frederic Sowa, and Rusty Russell.
2) PTP and timestamping support in bnx2x, from Michal Kalderon.
3) Allow adjusting the rx_copybreak threshold for a driver via
ethtool, and add rx_copybreak support to enic driver. From
Govindarajulu Varadarajan.
4) Significant enhancements to the generic PHY layer and the bcm7xxx
driver in particular (EEE support, auto power down, etc.) from
Florian Fainelli.
5) Allow raw buffers to be used for flow dissection, allowing drivers
to determine the optimal "linear pull" size for devices that DMA
into pools of pages. The objective is to get exactly the
necessary amount of headers into the linear SKB area pre-pulled,
but no more. The new interface drivers use is eth_get_headlen().
From WANG Cong, with driver conversions (several had their own
by-hand duplicated implementations) by Alexander Duyck and Eric
Dumazet.
6) Support checksumming more smoothly and efficiently for
encapsulations, and add "foo over UDP" facility. From Tom
Herbert.
7) Add Broadcom SF2 switch driver to DSA layer, from Florian
Fainelli.
8) eBPF now can load programs via a system call and has an extensive
testsuite. Alexei Starovoitov and Daniel Borkmann.
9) Major overhaul of the packet scheduler to use RCU in several major
areas such as the classifiers and rate estimators. From John
Fastabend.
10) Add driver for Intel FM10000 Ethernet Switch, from Alexander
Duyck.
11) Rearrange TCP_SKB_CB() to reduce cache line misses, from Eric
Dumazet.
12) Add Datacenter TCP congestion control algorithm support, From
Florian Westphal.
13) Reorganize sk_buff so that __copy_skb_header() is significantly
faster. From Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1558 commits)
netlabel: directly return netlbl_unlabel_genl_init()
net: add netdev_txq_bql_{enqueue, complete}_prefetchw() helpers
net: description of dma_cookie cause make xmldocs warning
cxgb4: clean up a type issue
cxgb4: potential shift wrapping bug
i40e: skb->xmit_more support
net: fs_enet: Add NAPI TX
net: fs_enet: Remove non NAPI RX
r8169:add support for RTL8168EP
net_sched: copy exts->type in tcf_exts_change()
wimax: convert printk to pr_foo()
af_unix: remove 0 assignment on static
ipv6: Do not warn for informational ICMP messages, regardless of type.
Update Intel Ethernet Driver maintainers list
bridge: Save frag_max_size between PRE_ROUTING and POST_ROUTING
tipc: fix bug in multicast congestion handling
net: better IFF_XMIT_DST_RELEASE support
net/mlx4_en: remove NETDEV_TX_BUSY
3c59x: fix bad split of cpu_to_le32(pci_map_single())
net: bcmgenet: fix Tx ring priority programming
...
Add two helpers so that drivers do not have to care of BQL being
available or not.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jim Davis <jim.epost@gmail.com>
Fixes: 29d40c9032 ("net/mlx4_en: Use prefetch in tx path")
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx_desc struct holds 8 __be64 values. The original code in
ring_tx_db() took a tx_desc pointer then casted it to an int pointer and
then casted it to a u64 pointer. It was confusing and triggered some
static checker warnings.
I have changed the cxgb_pio_copy() function to only take tx_desc
pointers. This isn't really a loss of flexibility because anything else
was buggy to begin with.
I also removed the casting on the destination pointer since that was
unnecessary and a bit messy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"cntxt_id" is an unsigned int but "udb" is a u64 so there is a potential
shift wrapping bug here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support skb->xmit_more in i40e is straightforward : we need to move
around i40e_maybe_stop_tx() call to correctly test netif_xmit_stopped()
before taking the decision to not kick the NIC.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a MPC8xx as a router, 'perf' shows a significant time spent in
fs_enet_interrupt() and fs_enet_start_xmit().
'perf annotate' shows that the time spent in fs_enet_start_xmit is indeed spent
between spin_unlock_irqrestore() and the following instruction, hence in
interrupt handling. This is due to the TX complete interrupt that fires after
each transmitted packet.
This patch modifies the handling of TX complete to use NAPI.
With this patch, my NAT router offers a throughput improved by 21%
Original performance:
[root@localhost tmp]# scp toto pgs:/tmp
toto 100% 256MB 2.8MB/s 01:31
Performance with the patch:
[root@localhost tmp]# scp toto pgs:/tmp
toto 100% 256MB 3.4MB/s 01:16
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the probe function, use_napi is inconditionnaly set to 1. This patch removes
all the code which is conditional to !use_napi, and removes use_napi which has
then become useless.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8168EP is Realtek PCIe Gigabit Ethernet controller with DASH support.
It is a successor chip of RTL8168DP.
For RTL8168EP, the read/write ocp register is via eri channel type 2, so I
move ocp_xxx() related functions under rtl_eri_xxx. And use r8168dp_ocp_xxx()
for RTL8168DP ocp read/write, r8168ep_ocp_xxx() for RTL8168EP ocp read/write.
The way of checking dash enable is different with RTL8168DP. I use
r8168dp_check_dash()for RTL8168DP and r8168ep_check_dash() for RTL8168EP,
to check if dash is enabled.
The driver_start() and driver_stop() of RTL8168EP is also different with
RTL8168DP. I use rtl8168dp_driver_xxx() for RTL8168DP and
rtl8168ep_driver_xxx for RTL8168EP.
Right now, RTL8168EP phy mcu did not need firmware code patch, so I did not
add firmware code for it.
so I did not add firmware code for it.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two macros used to copy BSSID information use ether_addr_copy(), thus
the arrays must be 2-byte aligned. In one case, the array could become
unaligned if the struct containing it were changed. Use the __unaligned(2)
attribute to retain the necessary alignment. In addition, the magic number
used to specify the size of the array is replaced by ETH_ALEN.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, ath9k uses a global counter for all
frames that need to be assigned a sequence number.
QoS-data frames are handled properly since they
have a per-tid counter. But, beacons and other
management frames use the same counter even if
multiple interfaces or contexts are present.
Fix this issue by making the counter per-interface
and using it when mac80211 sets IEEE80211_TX_CTL_ASSIGN_SEQ.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Here's the big USB patchset for 3.18-rc1. Also in here is the PHY tree,
as it seems to fit well with the USB tree for various reasons...
Anyway, lots of little changes in here, all over the place, full details
in the changelog below.
All have been in the linux-next tree for a while with no issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlQ0aLYACgkQMUfUDdst+ylBvwCgs9fGRj0RQkLyGhQdEpzdZtTU
ZcwAoMPBImnaA1ZeSl7ZnoO8vC/WE4bR
=tfpj
-----END PGP SIGNATURE-----
Merge tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB patchset for 3.18-rc1. Also in here is the PHY
tree, as it seems to fit well with the USB tree for various reasons...
Anyway, lots of little changes in here, all over the place, full
details in the changelog
All have been in the linux-next tree for a while with no issues"
* tag 'usb-3.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (244 commits)
USB: host: st: fix typo 'CONFIG_USB_EHCI_HCD_ST'
uas: Reduce number of function arguments for uas_alloc_foo functions
xhci: Allow xHCI drivers to be built as separate modules
xhci: Export symbols used by host-controller drivers
xhci: Check for XHCI_COMP_MODE_QUIRK when disabling D3cold
xhci: Introduce xhci_init_driver()
usb: hcd: add generic PHY support
usb: rename phy to usb_phy in HCD
usb: gadget: uvc: fix up uvcg_v4l2_get_unmapped_area typo
USB: host: st: fix ehci/ohci driver selection
usb: host: ehci-exynos: Remove unnecessary usb-phy support
usb: core: return -ENOTSUPP for all targeted hosts
USB: Remove .owner field for driver
usb: core: log higher level message on malformed LANGID descriptor
usb: Add LED triggers for USB activity
usb: Rename usb-common.c
usb: gadget: Refactor request completion
usb: gadget: Introduce usb_gadget_giveback_request()
usb: dwc2/gadget: move phy bus legth initialization
phy: remove .owner field for drivers using module_platform_driver
...
hw pointer of ath_hw is not assigned to proper value
in function ath9k_hw_reset what finally causes kernel panic.
This can be solved by proper initialization of ath_hw in
ath9k_init_priv.
Signed-off-by: Marek Puzyniak <marek.puzyniak@tieto.com>
Acked-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a channel context is removed, the hw_queue_base
is set to -1, this will result in a panic because
ath9k_chanctx_stop_queues() can be called on an interface
that is not assigned to any context yet - for example,
when trying to scan.
Fix this issue by setting the hw_queue_base to zero
when a channel context is removed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/ath/main.c:88 ath_printk()
error: we previously assumed 'common->hw' could be null (see line 82)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the allowed "respose rate" set (rates for HW generated frames
like ACKs) is the same as the basic rate set.
The HW will use the higher allowed response rate that is lower than the
rate of the received frame.
This is more or less what IEEE80211 mandates, but I missed the fact
that IEEE80211 also says that whenever it happens that for a modulation
class there is no any rate in the basic rates set, then the response rate
set shall include also all the mandatory rates for that modulation class.
This patch adds mandatory OFDM rates to the allowed response rate set if
no OFDM rate is included in the basic rate set.
Depending by the AP, I faced cases in which this patch seems to cause a
noticeable perfomance improvement.
- With my usual test AP there is no particular perfomance difference.
- With a prism54/hostapd AP this patch causes RX thoughput increase from
about 5Mbps to about 20Mbps.
Hopefully this patch may help people that faced performance regression wrt
the old staging driver.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Testing xmit_more support with netperf and connected UDP sockets,
I found strange dst refcount false sharing.
Current handling of IFF_XMIT_DST_RELEASE is not optimal.
Dropping dst in validate_xmit_skb() is certainly too late in case
packet was queued by cpu X but dequeued by cpu Y
The logical point to take care of drop/force is in __dev_queue_xmit()
before even taking qdisc lock.
As Julian Anastasov pointed out, need for skb_dst() might come from some
packet schedulers or classifiers.
This patch adds new helper to cleanly express needs of various drivers
or qdiscs/classifiers.
Drivers that need skb_dst() in their ndo_start_xmit() should call
following helper in their setup instead of the prior :
dev->priv_flags &= ~IFF_XMIT_DST_RELEASE;
->
netif_keep_dst(dev);
Instead of using a single bit, we use two bits, one being
eventually rebuilt in bonding/team drivers.
The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being
rebuilt in bonding/team. Eventually, we could add something
smarter later.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers should avoid NETDEV_TX_BUSY as much as possible.
They should stop the tx queue before qdisc even tries to push another
packet, to avoid requeues.
For a driver supporting skb->xmit_more, this is likely to be a prereq
anyway, otherwise we could have a tx deadlock : We need to force a
doorbell if TX ring is full.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 6f2b6a3005,
# 3c59x: Add dma error checking and recovery
the intent is to split out the mapping from the byte-swapping in order to
insert a dma_mapping_error() check.
Kinda this semantic patch:
// See http://coccinelle.lip6.fr/
//
// Beware, grouik-and-dirty!
@@
expression DEV, X, Y, Z;
@@
- cpu_to_le32(pci_map_single(DEV, X, Y, Z))
+ dma_addr_t addr = pci_map_single(DEV, X, Y, Z);
+ if (dma_mapping_error(&DEV->dev, addr))
+ /* snip */;
+ cpu_to_le32(addr)
However, the #else part (of the #if DO_ZEROCOPY test) is changed this way:
- cpu_to_le32(pci_map_single(DEV, X, Y, Z))
+ dma_addr_t addr = cpu_to_le32(pci_map_single(DEV, X, Y, Z));
// ^^^^^^^^^^^
// That mismatches the 3 other changes!
+ if (dma_mapping_error(&DEV->dev, addr))
+ /* snip */;
+ cpu_to_le32(addr)
Let's remove the leftover cpu_to_le32() for coherency.
v2: Better changelog.
v3: Add Acked-by
Fixes: 6f2b6a3005
# 3c59x: Add dma error checking and recovery
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Sylvain "ythier" Hitier <sylvain.hitier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GENET MAC has three Tx ring priority registers:
- GENET_x_TDMA_PRIORITY0 for queues 0-5
- GENET_x_TDMA_PRIORITY1 for queues 6-11
- GENET_x_TDMA_PRIORITY2 for queues 12-16
Fix bcmgenet_init_multiq() to program them correctly.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adjust fixed_phy_register() to return struct phy_device *, so that
it becomes easy to use fixed PHYs without device tree support:
phydev = fixed_phy_register(PHY_POLL, &fixed_phy_status, NULL);
fixed_phy_set_link_update(phydev, fixed_phy_link_update);
phy_connect_direct(netdev, phydev, handler_fn, phy_interface);
This change is a prerequisite for modifying bcmgenet driver to work
without a device tree on Broadcom's MIPS-based 7xxx platforms.
Signed-off-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a openvswitch compilation error when CONFIG_INET is not set:
=====================================================
In file included from include/net/geneve.h:4:0,
from net/openvswitch/flow_netlink.c:45:
include/net/udp_tunnel.h: In function 'udp_tunnel_handle_offloads':
>> include/net/udp_tunnel.h💯2: error: implicit declaration of function 'iptunnel_handle_offloads' [-Werror=implicit-function-declaration]
>> return iptunnel_handle_offloads(skb, udp_csum, type);
>> ^
>> >> include/net/udp_tunnel.h💯2: warning: return makes pointer from integer without a cast
>> >> cc1: some warnings being treated as errors
=====================================================
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Tx VLAN offloading is disabled frames with size ~ MTU are not
transmitted as the driver does not account 4 bytes of VLAN header added
by stack. It should use VLAN_ETH_HLEN instead of ETH_HLEN.
The second problem is with newer BNA chips (BNA 1860). These chips filter
out any VLAN tagged frames in Tx path. This is a problem when Tx VLAN
offloading is disabled and frames are tagged by stack. Older chips like
1010/1020 are not affected as they probably don't do such filtering.
Cc: Rasesh Mody <rasesh.mody@qlogic.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restart autonegotiation is necessary after setting EEE.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier change to use usable slave array for TLB mode had an additional
performance advantage. So extending the same logic to all other modes
that use xmit-hash for slave selection (viz 802.3AD, and XOR modes).
Also consolidating this with the earlier TLB change.
The main idea is to build the usable slaves array in the control path
and use that array for slave selection during xmit operation.
Measured performance in a setup with a bond of 4x1G NICs with 200
instances of netperf for the modes involved (3ad, xor, tlb)
cmd: netperf -t TCP_RR -H <TargetHost> -l 60 -s 5
Mode TPS-Before TPS-After
802.3ad : 468,694 493,101
TLB (lb=0): 392,583 392,965
XOR : 475,696 484,517
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a trivial fix to display xmit_hash_policy for this new TLB mode
since it uses transmit-hash-poilicy as part of bonding-master info
(/proc/net/bonding/<bonding-interface).
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DEFINE_XENBUS_DRIVER() macro looks a bit weird and causes sparse
errors.
Replace the uses with standard structure definitions instead. This is
similar to pci and usb device registration.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Instead of setting inline threshold using module parameter only on
driver load, use set_tunable() to set it dynamically.
No need to store the threshold per ring, using instead the netdev global
priv->prof->inline_thold
Initial value still is set using the module parameter, therefore
backward compatability is kept.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorganize code to call is_inline() once, so compiler can inline it
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Properly clear tx_info->ts_requested
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access skb_headlen() once in tx flow
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acces skb_shinfo(skb) once in tx flow.
Also, rename @i variable to @i_frag to avoid confusion, as the "goto
tx_drop_unmap;" relied on this @i variable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_process_tx_cq() carefully fetches and writes ring->last_nr_txbb
and ring->cons only one time to avoid false sharing
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_free_tx_desc() uses a prefetchw(&skb->users) to speed up
consume_skb()
prefetchw(&ring->tx_queue->dql) to speed up BQL update
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add frag0_dma/frag0_byte_count into mlx4_en_tx_info to avoid a cache
line miss in TX completion for frames having one dma element. (We avoid
reading back the tx descriptor)
Note this could be extended to 2/3 dma elements later, as we have free
room in mlx4_en_tx_info
Also, mlx4_en_free_tx_desc() no longer accesses skb_shinfo(). We use a
new nr_maps fields in mlx4_en_tx_info to avoid 2 or 3 cache misses.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Try to allocate using kmalloc_node() first, only on failure use
vmalloc()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- doorbell_qpn is stored in the cpu_to_be32() way to avoid bswap() in fast
path.
- mdev->mr.key stored in ring->mr_key to also avoid bswap() and access to
cold cache line.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorganize struct mlx4_en_tx_ring to have:
- One cache line containing last_nr_txbb & cons & wake_queue, used by tx
completion.
- One cache line containing fields dirtied by mlx4_en_xmit()
- Following part is read mostly and shared by cpus.
Align struct mlx4_en_tx_info to a cache line
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Remove unused variable ring->poll_cnt
- No need to set some fields if using blueflame
- Add missing const's
- Use unlikely
- Remove unneeded new line
- Make some comments more precise
- struct mlx4_bf @offset field reduced to unsigned int to save space
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When fec_enet_alloc_buffers() fails we should better undo the previous actions,
which consists of: disabling the FEC clocks and putting the FEC pins into
inactive state.
The error path for fec_enet_mii_probe() is kept unchanged.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO_BCM_UNIMAC needs HAS_IOMEM, so depend on it, the related error (
with allmodconfig under um):
MODPOST 1205 modules
ERROR: "devm_ioremap" [drivers/net/phy/mdio-bcm-unimac.ko] undefined!
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
git checkout 1b7bde6d65
make.cross ARCH=m68k m5275evb_defconfig
make.cross ARCH=m68k
All error/warnings:
drivers/net/ethernet/freescale/fec_main.c: In function 'fec_enet_rx_queue':
>> drivers/net/ethernet/freescale/fec_main.c:1470:3: error: implicit declaration of function 'prefetch' [-Werror=implicit-function-declaration]
prefetch(skb->data - NET_IP_ALIGN);
^
cc1: some warnings being treated as errors
missed included prefetch.h
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_mii_setup() is called from the PHY state machine every 1-2 seconds
when the PHYs are in PHY_POLL mode.
Improve bcmgenet_mii_setup() so that it touches the MAC registers only when
the link is up and there was a change to link, speed, duplex, or pause status.
Signed-off-by: Petri Gynther <pgynther@google.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids PHY and MDIO probing if no PHY chip is present.
This is the case mainly in optical links where there is no need for
PHY chip, and therefore no need of MDIO. In this scenario Ethernet
MAC is directly connected to an optical module through an external
SFP transceiver.
Signed-off-by: Walter Lozano <walter@vanguardiasur.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move PHY get addr and MDIO create to a new function to improve readability
and make it easier to avoid its usage. This will be useful for example in
the case where there is no PHY chip.
Signed-off-by: Walter Lozano <walter@vanguardiasur.com.ar>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-10-03
Please pull tihs batch of updates intended for the 3.18 stream!
For the iwlwifi bits, Emmanuel says:
"I have here a few things that depend on the latest mac80211's changes:
RRM, TPC, Quiet Period etc... Eyal keeps improving our rate control
and we have a new device ID. This last patch should probably have
gone to wireless.git, but at that stage, I preferred to send it to
-next and CC stable."
For (most of) the Atheros bits, Kalle says:
"The only new feature is testmode support from me. Ben added a new method
to crash the firmware with an assert for debug purposes. As usual, we
have lots of smaller fixes from Michal. Matteo fixed a Kconfig
dependency with debugfs. I fixed some warnings recently added to
checkpatch."
For the NFC bits, Samuel says:
"We've had major updates for TI and ST Microelectronics drivers, and a
few NCI related changes.
For TI's trf7970a driver:
- Target mode support for trf7970a
- Suspend/resume support for trf7970a
- DT properties additions to handle different quirks
- A bunch of fixes for smartphone IOP related issues
For ST Microelectronics' ST21NFCA and ST21NFCB drivers:
- ISO15693 support for st21nfcb
- checkpatch and sparse related warning fixes
- Code cleanups and a few minor fixes
Finally, Marvell added ISO15693 support to the NCI stack, together with a
couple of NCI fixes."
For the Bluetooth bits, Johan says:
"This 3.18 pull request replaces the one I did on Monday ("bluetooth-next
2014-09-22", which hasn't been pulled yet). The additions since the last
request are:
- SCO connection fix for devices not supporting eSCO
- Cleanups regarding the SCO establishment logic
- Remove unnecessary return value from logging functions
- Header compression fix for 6lowpan
- Cleanups to the ieee802154/mrf24j40 driver
Here's a copy from previous request that this one replaces:
'
Here are some more patches for 3.18. They include various fixes to the
btusb HCI driver, a fix for LE SMP, as well as adding Jukka to the
MAINTAINERS file for generic 6LoWPAN (as requested by Alexander Aring).
I've held on to this pull request a bit since we were waiting for a SCO
related fix to get sorted out first. However, since the merge window is
getting closer I decided not to wait for it. If we do get the fix sorted
out there'll probably be a second small pull request later this week.
'"
And,
"Unless 3.17 gets delayed this will probably be our last -next pull request for
3.18. We've got:
- New Marvell hardware supportr
- Multicast support for 6lowpan
- Several of 6lowpan fixes & cleanups
- Fix for a (false-positive) lockdep warning in L2CAP
- Minor btusb cleanup"
On top of all that comes the usual sort of updates to ath5k, ath9k,
ath10k, brcmfmac, mwifiex, and wil6210. This time around there are
also a number of rtlwifi updates to enable some new hardware and
to reconcile the in-kernel drivers with some newer releases of the
Realtek vendor drivers. Also of note is some device tree work for
the bcma bus.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Signedness bugs may occur when using signed char for bitops,
depending on if the highest bit is ever used.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signedness bugs may occur when using signed char for bitops,
depending on if the highest bit is ever used.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the spider_net_get_mac_address() call at the end of
the spider_net_set_mac() function. The dev->dev_addr is instead updated
with a memcpy() from sa->sa_data.
Since spider_net_get_mac_address() is not used anywhere else, this patch
also removes the function.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the packet is successfully sent, we should not touch the packet
as it may have been freed. This patch is based on the work done by
Long Li <longli@microsoft.com>.
David, please queue this up for stable.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When team_notify_peers and team_mcast_rejoin are called, they both reset
their respective .count_pending atomic variable. Then when the actual
worker function is executed, the variable is atomically decremented.
This pattern introduces a potential race condition where the
.count_pending rolls over and the worker function keeps rescheduling
until .count_pending decrements to zero again:
THREAD 1 THREAD 2
======== ========
team_notify_peers(teamX)
atomic_set count_pending = 1
schedule_delayed_work
team_notify_peers(teamX)
atomic_set count_pending = 1
team_notify_peers_work
atomic_dec_and_test
count_pending = 0
(return)
schedule_delayed_work
team_notify_peers_work
atomic_dec_and_test
count_pending = -1
schedule_delayed_work
(repeat until count_pending = 0)
Instead of assigning a new value to .count_pending, use atomic_add to
tack-on the additional desired worker function invocations.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Fixes: fc423ff00d ("team: add peer notification")
Fixes: 492b200efd ("team: add support for sending multicast rejoins")
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit bc23333ba1 ("net:
bcmgenet: fix bcmgenet_put_tx_csum()"), we need to return the skb
pointer in case we had to reallocate the SKB headroom.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool -S reports a new counter, tracking number of time doorbell
was not triggered, because skb->xmit_more was set.
$ ethtool -S eth0 | egrep "tx_packet|xmit_more"
tx_packets: 2413288400
xmit_more: 666121277
I merged the tso_packet false sharing avoidance in this patch as well.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SH_IRDA needs HAS_IOMEM, so depend on it. The related error(with
allmodconfig under um):
CC [M] drivers/net/irda/sh_irda.o
drivers/net/irda/sh_irda.c: In function ‘sh_irda_probe’:
drivers/net/irda/sh_irda.c:776:2: error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration]
self->membase = ioremap_nocache(res->start, resource_size(res));
^
drivers/net/irda/sh_irda.c:776:16: warning: assignment makes pointer from integer without a cast [enabled by default]
self->membase = ioremap_nocache(res->start, resource_size(res));
^
drivers/net/irda/sh_irda.c:821:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(self->membase);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PXA168_ETH need HAS_IOMEM, so depend on it, the related error (with
allmodconfig under um):
CC [M] drivers/net/ethernet/marvell/pxa168_eth.o
drivers/net/ethernet/marvell/pxa168_eth.c: In function ‘pxa168_eth_probe’:
drivers/net/ethernet/marvell/pxa168_eth.c:1605:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(pep->base);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_DSA_BCM_SF2 need HAS_IOMEM, so depend on it, the related error (with
allmodconfig under um):
CC [M] drivers/net/dsa/bcm_sf2.o
drivers/net/dsa/bcm_sf2.c: In function ‘bcm_sf2_sw_setup’:
drivers/net/dsa/bcm_sf2.c:487:3: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(*base);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CAN_AT91 needs HAS_IOMEM, so depends on it. The related error (with
allmodconfig under um):
CC [M] drivers/net/can/at91_can.o
drivers/net/can/at91_can.c: In function ‘at91_can_probe’:
drivers/net/can/at91_can.c:1329:2: error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration]
addr = ioremap_nocache(res->start, resource_size(res));
^
drivers/net/can/at91_can.c:1329:7: warning: assignment makes pointer from integer without a cast [enabled by default]
addr = ioremap_nocache(res->start, resource_size(res));
^
drivers/net/can/at91_can.c:1384:2: error: implicit declaration of function ‘iounmap’ [-Werror=implicit-function-declaration]
iounmap(addr);
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-10-02
This series contains updates to fm10k, igb, ixgbe and i40e.
Alex provides two updates to the fm10k driver. First reduces the buffer
size to 2k for all page sizes, since most frames only have a 1500 MTU
so supporting a buffer size larger than this is somewhat wasteful.
Second fixes an issue where the number of transmit queues was not being
updated, so added the lines necessary to update the number of transmit
queues.
Rick Jones provides two patches to convert ixgbe, igb and i40e to use
dev_consume_skb_any().
Emil provides two patches for ixgbe, first cleans up a couple of wait
loops on auto-negotiation that were not needed. Second fixes an issue
reported by Fujitsu/Red Hat, which consolidates the logic behind the
dynamically setting of TXDCTL.WTHRESH depending on interrupt throttle
rate (ITR) setting regardless of BQL.
Ethan Zhao provides a cleanup patch for ixgbe where he noticed a
duplicate define.
Bernhard Kaindl provides a patch for igb to remove a source of latency
spikes by not calling code that uses mdelay() for feeding a PHY stat
while being called with a spinlock held.
Todd bumps the igb version based on the recent changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the upcoming ConnectX-4 device to the list of supported devices by then
mlx5 driver.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch puts a common part as the first field of mlx5_core_qp. This field is
used to identify which resource generated an event. This is required since upcoming
new resource types such as DC targets are allocated for the same numerical space
as regular QPs and may generate the same events. By searching the resource in the
same table we can then look at the common field to identify the resource.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transform device capabilities related commands to use set/get macros to
manipulate command mailboxes.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an auto generated header file that describes hardware registers along with
set of macros that set/get values. The macros do static checks to avoid
overflow, handle endianess, and overall provide a clean way to code commands.
Currently the header file is small and we will add structs as we make use of
the macros.
A few commands were removed from the commands enum since they are not supported
currently and will be added when support is available.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange struct mlx5_caps so it has a "gen" field to represent the current
capabilities configured for the device. Max capabilities can also be queried
from the device. Also update capabilities struct to contain more fields as per
the latest revision if firmware specification.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resume the device before setting the MAC address.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I've noticed every time the interface is set to 'up,', the kernel
reports that the link speed is set to 100 Mbps/Full Duplex, even
when ethtool is used to set autonegotiation to 'off', half
duplex, 10 Mbps.
It can be tested by:
ifconfig eth0 down
ethtool -s eth0 autoneg off speed 10 duplex half
ifconfig eth0 up
Then checking 'dmesg' for the link speed.
Signed-off-by: Michel Stam <m.stam@fugro.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to call ether_setup after alloc_ethdev since it was
already called there.
Follow commits c706471b26 ("net: axienet: remove unnecessary
ether_setup after alloc_etherdev") and 3c87dcbfb3 ("net: ll_temac:
Remove unnecessary ether_setup after alloc_etherdev") and fix the
pattern in all remaining ethernet drivers.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the ethernet driver for Agere et131x devices to
drivers/net/ethernet.
The driver being added has been in the staging tree for some time, and will be
removed from there in a seperate patch. This one merely disables the staging
version to prevent two instances being built.
Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indenting errors yielded the following static checker warnings:
drivers/net/wireless/rtlwifi/rtl8192ee/hw.c:533 rtl92ee_set_hw_reg() warn: add curly braces? (if)
drivers/net/wireless/rtlwifi/rtl8192ee/hw.c:539 rtl92ee_set_hw_reg() warn: add curly braces? (if)
An unreleased version of the static checker also reported:
drivers/net/wireless/rtlwifi/rtl8723be/trx.c:550 rtl8723be_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8188ee/trx.c:621 rtl88ee_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8192ee/trx.c:567 rtl92ee_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8821ae/trx.c:758 rtl8821ae_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:494 rtl8723e_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8192se/trx.c:315 rtl92se_rx_query_desc() warn: 'hdr' can't be NULL.
drivers/net/wireless/rtlwifi/rtl8192ce/trx.c:392 rtl92ce_rx_query_desc() warn: 'hdr' can't be NULL.
All of these are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver needs btcoexist, but Kconfig fails to select it. This omission
could cause build errors for some configurations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we are attempting to switch to a new
channel context, the TX queues are flushed, but
the mac80211 queues are not stopped and traffic
can still come down to the driver.
This patch fixes it by stopping the queues
assigned to the current context/vif before
trying to flush.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a full chip reset is done, all the queues
across all VIFs are stopped, but if MCC is enabled,
only the queues of the current context is awakened,
when we complete the reset.
This results in unfairness for the inactive context.
Since frames are queued internally in the driver if
there is a context mismatch, we can awaken all the
queues when coming out of a reset.
The VIF-specific queues are still used in flow control,
to ensure fairness when traffic is high.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be used when the queues of a context
needs to be stopped.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change the ath9k_chanctx_wake_queues() API so
that we can pass the channel context that needs its
queues to be stopped.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When draining of the TX queues fails, a
full HW reset is done. ath_reset() makes sure
that the queues in mac80211 are restarted,
so there is no need to wake them up again.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_has_tx_pending() can be used to
check if there are pending frames instead
of having duplicate code.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Checking for the queue depth outside of
the TX queue lock is incorrect and in this
case, is not required since it is done inside
ath9k_has_pending_frames().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to check if the current
channel context has active ACs queued up
if the TX queue is not empty.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds SD8887 support to mwifiex.
SD8887 is Marvell's 1x1 11ac solution.
The corresponding firmware image file is located at:
"mrvl/sd8887_uapsta.bin"
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds some more defitions to card specific register structure
and removes static defines for these registers.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce netdev IOCTLs, to be used by the debug tools.
Allows to read/write single dword value or
memory block, aligned to dword
Different address modes supported:
- BAR offset
- Firmware "linker" address
- target's AHB bus
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce manual FW recovery mode. It is activated if module parameter
@no_fw_recovery set to true. May be changed at runtime.
Recovery information provided by new "recovery" debugfs file. It prints:
mode = [auto|manual]
state = [idle|pending|running]
In manual mode, after FW error, recovery won't start automatically. Instead,
after notification to user space, recovery waits in "pending" state, as indicated by the
"recovery" debugfs file. User space tools may perform data collection and allow to
continue recovery by writing "run" to the "recovery" debugfs file.
Alternatively, recovery pending may be canceled by stopping network interface
i.e. 'ifconfig wlan0 down'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In these Makefiles, at least one of "obj-y" and "obj-" is non-empty,
hence built-in.o is always created without such a trick.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Peter Foley <pefoley2@pefoley.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au> [shmobile]
Acked-by: David S. Miller <davem@davemloft.net> [networking]
Signed-off-by: Michal Marek <mmarek@suse.cz>
Bump version
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert two more Intel NIC drivers to dev_consume_skb_any() to help
make dropped packet profiling sane.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove a source of latency spikes (in my case up to 10ms) by not calling
code that uses mdelay() for feeding a phy statistic (rx errors for idle
symbols - not data -> idle_errors) while being called with a spinlock held.
As idle_errors isn't read, this patch only removes unused code and data.
Later, more complicated changes may be applied to address the spinlock and
allow for some PHY diagnostics by harvesting this PHY stats register fully.
This patch is designed to fix the issue and be safe for longterm/stable.
For the Intel e1000e driver, the same change was applied in 2008 with
commit 23033fad5b ("e1000e: remove phy read from inside spinlock").
The mdelay is triggered by HW/SW semaphores, thus it depends on the HW.
I've HW that triggers it even when idle. Others may trigger it only e.g.
when Ethernet ports aquire or loose the link or on ifconfig up / down.
We've noticed this first from delays in frame rx/tx due to the mdelay().
Example command for checking if the issue is triggered: cyclictest -Smp1
(Look for occasional "Max:" values > 4000 or use -b 4000 to stop if greater)
It was observed with I350 ports connected to other I350 ports, but not
if driver and EEPROM was modified to run the I350 in EEPROM-less mode.
phy_stats.idle_errors and .receive_errors (isn't touched) occupy 64 not
used bits in the adapter struct: Their allocation may be removed as well.
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Fixes: 12dcd86b75 ("igb: fix stats handling") (this added the spin_lock)
Signed-off-by: Bernhard Kaindl <bk-linux@use.startmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is typo in ixgbe.h, two marcro definition of IXGBE_MAX_L2A_QUEUES to 4,
delete one, clear the compiler warning.
Signed-off-by: Ethan Zhao <ethan.zhao@oracle.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch consolidates the logic behind dynamically setting TXDCTL.WTHRESH
depending on interrupt throttle rate (ITR) setting regardless of BQL.
Previously TXDCTL.WTHRESH was dynamically being set only with BQL being
enabled, but we have to set it regardless of BQL when ITR is low to avoid
Tx stalls/hangs.
CC: John Greene <jogreene@redhat.com>
Reported by: Masayuki Gouji <gouji.masayuki@jp.fujitsu.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes couple of wait loops on autoneg that are not needed.
During validation we noticed that the loops always time out, so there
should be no user impact.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Convert the normal packet completion path to dev_consume_skb_any() so
packet drop profiling via dropwatch or perf top -G -e skb_kfree_skb
is not cluttered with false hits.
Compile tested only. There is a dev_kfree_skb_any() in the routine
ixgbe_ptp_tx_hwtstamp() in ixgbe_ptp.c that looks like a conversion
candidate but I wasn't familiar enough with the code to pull the
trigger.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The number of Tx queues was not being updated due to some issues when
generating the patches. This change makes sure to add the lines necessary
to update the number of Tx queues correctly.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change reduces the buffer size to 2K for all page sizes. The basic
idea is that since most frames only have a 1500 MTU supporting a buffer
size larger than this is somewhat wasteful. As such I have reduced the
size to 2K for all page sizes which will allow for more uses per page.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_put_tx_csum() needs to return skb pointer back to the caller
because it reallocates a new one in case of lack of skb headroom.
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call skb_set_inner_protocol to set inner Ethernet protocol to
ETH_P_TEB before transmit. This is needed for GSO with UDP tunnels.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Copy short frames and keep the buffers mapped, re-allocate skb instead of
memory copy for long frames.
- Add support for setting/getting rx_copybreak using generic ethtool tunable
Changes V3:
* As Eric Dumazet's suggestion that removing the copybreak module parameter
and only keep the ethtool API support for rx_copybreak.
Changes V2:
* Implements rx_copybreak
* Rx_copybreak provides module parameter to change this value
* Add tunable_ops support for rx_copybreak
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware would be clear when the power cut is enabled for
RTL8153.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xxx_clear_bp() is used to halt the firmware. It only necessary
for updating the new firmware. Besides, depend on the version of
the current firmware, it may have problem to halt the firmware
directly. Finally, halt the firmware would let the firmware code
useless, and the bugs which are fixed by the firmware would occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver, similar to tg3, has a check that will
cause full sized 802.1ad frames to be dropped. The
frame will be larger then the standard mtu due to the
presense of vlan header that has not been stripped.
The driver should not drop this frame and should process
it just like it does for 802.1q.
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a vlan-tagged frame that still contains
a vlan header, the length of the packet will be greater
then MTU+ETH_HLEN since it will account of the extra
vlan header. TG3 checks this for the case for 802.1Q,
but not for 802.1ad. As a result, full sized 802.1ad
frames get dropped by the card.
Add a check for 802.1ad protocol when receving full
sized frames.
Suggested-by: Prashant Sreedharan <prashant@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These two functions are used to inform dash firmware that driver is been
brought up or brought down. So call these two functions only when hardware dash
function is enabled.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function "rtl8168_oob_notify", using function "rtl_eri_write" to access
eri register 0xe8, instead of using MAC register "ERIDR" and "ERIAR" to
access it.
For using function "rtl_eri_write" in function "rtl8168_oob_notify", need to
move down "rtl8168_oob_notify" related functions under the function
"rtl_eri_write".
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DASH function not only RTL8168DP can support, but also RTL8168EP.
So change the name of function "r8168dp_check_dash" to "r8168_check_dash".
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the name of function "rtl_w1w0_eri" to "rtl_w0w1_eri".
In this function, the local variable "val" is "write zeros then write ones".
Please see below code.
(val & ~m) | p
In this patch, change the function name from "xx_w1w0_xx" to "xx_w0w1_xx".
The changed function name is more suitable for it's behavior.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change function name from "rtl_w1w0_phy" to "rtl_w0w1_phy".
And its behavior from "write ones then write zeros" to
"write zeros then write ones".
In Realtek internal driver, bitwise operations are almost "write zeros then
write ones". For easy to port hardware parameters from Realtek internal driver
to Linux kernal driver "r8169", we would like to change this function's
behavior and its name.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For RTL8168F RTL8168FB RTL8168G RTL8168GU RTL8411 RTL8411B RTL8402 RTL8107E,
the magic packet enable bit is changed to eri 0xde bit0.
In this patch, change magic packet enable bit of these chips to eri 0xde bit0.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8168FB RTL8168G RTL8168GU RTL8411 RTL8411B RTL8106EUS RTL8402 can
support get mac address from backup mac address register.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the error cases for vnet_start_xmit()'s "out_dropped" label
is port == NULL, so only mess with port->clean_timer when port is not NULL.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling ether_setup is redundant since alloc_etherdev calls it.
Signed-off-by: Subbaraya Sundeep Bhatta <sbhatta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vio_dring_avail() will allow use of every dring entry, but when the last
entry is allocated then dr->prod == dr->cons which is indistinguishable from
the ring empty condition. This causes the next allocation to reuse an entry.
When this happens in sunvdc, the server side vds driver begins nack'ing the
messages and ends up resetting the ldc channel. This problem does not effect
sunvnet since it checks for < 2.
The fix here is to just never allocate the very last dring slot so that full
and empty are not the same condition. The request start path was changed to
check for the ring being full a bit earlier, and to stop the blk_queue if
there is no space left. The blk_queue will be restarted once the ring is
only half full again. The number of ring entries was increased to 512 which
matches the sunvnet and Solaris vdc drivers, and greatly reduces the
frequency of hitting the ring full condition and the associated blk_queue
stop/starting. The checks in sunvent were adjusted to account for
vio_dring_avail() returning 1 less.
Orabug: 19441666
OraBZ: 14983
Signed-off-by: Dwight Engen <dwight.engen@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sends ICMP and ICMPv6 messages for Path MTU Discovery when a remote
port MTU is smaller than the device MTU. This allows mixing newer VIO protocol
devices that support MTU negotiation with older devices that do not on the
same vswitch. It also allows Linux-Linux LDOMs to use 64K-1 data packets even
though Solaris vswitch is limited to <16K MTU.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows an admin to set the MTU on a sunvnet device to arbitrary
values between the minimum (68) and maximum (65535) IPv4 packet sizes.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes pre-allocated transmit buffers and instead directly maps
pending packets on demand. This saves O(n^2) maximum-sized transmit buffers,
for n hosts on a vswitch, as well as a copy to those buffers.
Single-stream TCP throughput linux-solaris dropped ~5% for 1500-byte MTU,
but linux-linux at 1500-bytes increased ~20%.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch upgrades the sunvnet driver to support VIO protocol version 1.6.
In particular, it adds per-port MTU negotiation, allowing MTUs other than
ETH_FRAMELEN with ports using newer VIO protocol versions.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dependency to COMPILE_TEST so that the driver can be compiled for
test purposes.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Berlin SoCs have an Ethernet controller compatible with the pxa168.
Allow these SoCs to use the pxa168_eth driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rework the way the MAC address is retrieved. The MAC address
can now, in addition to being random, be set in the device tree or
retrieved from the Ethernet controller MAC address registers. The
probing function will try to get a MAC address in the following order:
- From the device tree.
- From the Ethernet controller MAC address registers.
- Generate a random one.
This patch also adds a function to read the MAC address from the
Ethernet Controller registers.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing the MAC address, in addition to updating the dev_addr in
the net_device structure, this patch also update the MAC address
registers (high and low) of the Ethernet controller with the new MAC.
The address stored in these registers is used for IEEE 802.3x Ethernet
flow control, which is already enabled.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.3x Ethernet flow control is disabled when bit (1 << 2) is set
in the port status register. Fix the flow control detection in the link
event handling function which was relying on the opposite assumption.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the device tree support to the pxa168_eth driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up a bit the pxa168_eth driver before adding the device tree
support.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
ConnectX2 HCAs have max_mtu=4k and max_vl=8 vls. However, if you specify
a 4K mtu, the max_vl supported for 4K is 4 vls. The driver at startup
attempts to set a 4K mtu using the max_vl value obtained from QUERY_PORT.
Since the max_vl value is 8 vls (which is supported up to 2K mtu size),
the first attempt to set the mtl/vl port value will fail, generating
the following error message in the log:
mlx4_core 0000:06:00.0: command 0xc failed: fw status = 0x40
The driver then tries again, using mtu=4k, vls=4, and this succeeds.
Since we do not want to have this error message always displayed at driver
start when there are ConnectX2 HCAs on the host, we deprecate the error
message for this specific command/input_modifier/opcode_modifier/fw-status
to be debug.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlx4_QUERY_PORT_wrapper implements only the
QUERY_PORT "general" case (opcode modifier = 0).
Verify that the opcode modifier is zero, and also that the
input modifier contains only the port number in bits 0..7
(all other bits should be zero).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the new flow, we separate the pci initialization and teardown
from the initialization and teardown of the other resources.
__mlx4_init_one handles the pci resources initialization. It then
calls mlx4_load_one to initialize the remainder of the resources.
When removing a device, mlx4_remove_one is invoked. However, now
mlx4_remove_one calls mlx4_unload_one to free all the resources except the pci
resources. When mlx4_unload_one returns, mlx4_remove_one then frees the
pci resources.
The above separation will allow us to implement 'reset flow' in the future.
It will also enable more EQs for VFs and is a pre-step to the modern API to
enable/disable SRIOV.
Also added nvfs; an integer array of size MLX4_MAX_PORTS + 1; to the mlx4_dev
struct. This new field is used to avoid parsing the num_vfs module parameter
each time the mlx4_restart_one is called.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unloading the host driver while there are VFs active on VMs,
the PF driver disabled sriov anyway, causing kernel crashes.
We now leave SRIOV enabled, to avoid that.
When the driver is reloaded, __mlx4_init_one is invoked on the PF.
It now checks to see if SRIOV is already enabled on the PF -- and
if so does not enable sriov again.
Signed-off-by: Tal Alon <talal@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag of RTL8152_UNPLUG should only be set when the device is
unplugged, not each time the rtl8152_disconnect() is called.
Otherwise, the device wouldn't be stopped normally.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Driver is not updating sw_consumer while processing Tx completion
when interface is going down. Due to this interface down path gets
stuck forever waiting for NAPI to complete.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o __netxen_nic_down() function might sleep while holding spinlock_t(tx_clean_lock).
Acquire this lock for only releasing TX buffers instead of taking it
for whole down path.
Reported-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuration randconfig-1412075201 gets an error because driver rtl8821ae
depends on driver btcoexist, but Kconfig does not select it.
Reported-by: Jim Davis <jim.epost@gmail.com>
Cc: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When mwifiex device becomes GO, unicast traffic between client1 and GO stops
when client2 connects to GO. Reason behind this was PTK getting
overwritten by key_material command for client2 as it did not have client
mac address. So, client1 can no more decode GO's ping packets though it
responds to its broadcast packets.
This patch adds case to check for BSS_ROLE instead of bss_type to set
client mac address while configuring keys when device becomes GO.
Signed-off-by: Maithili Hinge <maithili@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9003, tx control and tx status are in separate descriptor rings.
Tx duration is extracted from the tx control descriptor data, which
ar9003_hw_proc_txdesc cannot access.
Fix getting the duration by adding a separate callback for it.
Acked-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
chan_lock is not required for checking if
we are in the middle of a HW reset, so do it
early. This also removes the small window
where the lock is dropped and reacquired.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add basic wowl (magic packet and disconnect) support. This patch adds
this support only for PCIE bus devices. This feature requires FW which
has support for wowl built in.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When driver gets unloaded due to error situation there is a chance
a packet gets received while fws has already been cleaned up. This
will result in kernel crash. This patch adds a check to avoid this
crash.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to provision the P2P_DEVICE mac address using p2p_da_override iovar
the discovery interface must be disabled. On some targets setting the mac
address failed so disable the discovery interface to be certain.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Msgbuf is using GFP_ATOMIC where GFP_KERNEL is also sufficient. On
some platforms the coherent DMA memory is very limited when using
GFP_ATOMIC. This patch changes usage of GFP_ATOMIC to GFP_KERNEL and
uses worker to make this possible for creation of flowring.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need a cast to assure correct value is propagated.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase driver scan timeout from 8 to 10 seconds and report results
to cfg80211. Without this patch the already received results were
dropped on driver timeout.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR934x and newer SoC devices, the layout of the AR_RTC_PLL_CONTROL
register changed. This currently breaks at least 5/10 MHz operation.
AR933x uses the old layout.
It might also have been causing other stability issues because of the
different location of the PLL_BYPASS bit which needs to be set during
PLL clock initialization.
This patch also removes more instances of hardcoded register values in
favor of properly computed ones with the PLL_BYPASS bit added.
Reported-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The cycpwr_thr1 value needs to be lower on the extension channel than on
the control channel, similar to how the register settings are programmed
in the initvals.
Also drop the unnecessary check for HT40 - this register can always be
written. This patch has been reported to improve HT40 stability and
throughput in some environments.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
