If the user moves directly from one button to another then we won't get a
no buttons pressed event and will therefore end up reporting that two
buttons are simultaneously pressed which isn't supported by the hardware.
Make sure we clear any existing button reports before reporting any new
ones.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In pathological cases the microphone detection may fail to report, for
example due to a failure to get a stable measurement. Provide a timeout
to cover such cases.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rather than measuring both HP channels we can simply directly measure the
microphone impedance and then rely on MICDET for final confirmation of the
presence of a suitable microphone. This improves the overall performance
of the identification process.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This extra check makes the procedure take longer and is of marginal use
in identification so do not execute it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sometimes we can trigger measurements early if contacts are shorted during
a slow insertion. As well as debouncing add further robustness by retrying
if we get a high impedance measurement for headphones as this can indicate
that the headphones were not yet connected.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Occasionally we can trigger an interrupt before we have completed
impedance measurement, although the valid bit will still be set. This
patch spins reading the impedance value until a valid value is seen.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In cases where we see a brief (dis)connection of the jack detection signals
we may see a noop jack insertion or removal where the jack has returned to
the original state by the time the interrupt is serviced. Suppress these
events in order to save work and avoid confusing the rest of the code.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure greater reliability by increasing the minimum threashold for
identifying a microphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no need to do this as HPDET identification will cause MICBIAS to
be powered down again.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Arizona button detection circuit is configurable, allowing the system
integrator to program a range of thresholds for the buttons supported on
the accessory but currently the driver uses the default button ranges and
does not provide any flexibility in how this is exposed to the application
layer.
Provide platform data allowing the user to control this and to map
the buttons to keys in the input subsystem.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In some pathological use cases users may insert an accessory very slowly
causing multiple indeterminate measurements. Handle this by retrying many
measurements before we give up and declare a headphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Running HPDET while the headphone outputs are enabled can disrupt the
operation of HPDET. In order to avoid this HPDET needs to disable the
headphone outputs and ASoC needs to not enable them while HPDET is
running.
For extcon instead of checking if the headphone output is enabled when
doing magic application unconditionally disable the output and restore
the state which ASoC wants set when undoing the magic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We have a very similar sequence doing magic writes in several places
(one of which missed an update to interlock with the CODEC driver) so
factor it out into a function.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch set default value of MUIC register to bring up MUIC device.
If user don't set some initial value for MUIC device through platform data,
extcon-max77693 driver use 'default_init_data' to bring up base operation
of MAX77693 MUIC device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch fix wrong pointer of platform data. If each machine set
platform data for h/w path or delay time of workqueue, this driver
happen kernel panic related to null pointer.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch check the pointer of platform data to protect
kernel panic when platform data is not used and code clean.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei, hyperv, ipack,
extcon, vmci, etc.).
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmZJgACgkQMUfUDdst+ymhZgCgo2dn37r9uMCwgTSpxSq92Je5
x8kAnRF1UnD6ZvySRIlLUBV5LW1YgFnK
=i5HH
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver patches from Greg Kroah-Hartman:
"Here's the big char/misc driver patches for 3.9-rc1.
Nothing major here, just lots of different driver updates (mei,
hyperv, ipack, extcon, vmci, etc.).
All of these have been in the linux-next tree for a while."
* tag 'char-misc-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (209 commits)
w1: w1_therm: Add force-pullup option for "broken" sensors
w1: ds2482: Added 1-Wire pull-up support to the driver
vme: add missing put_device() after device_register() fails
extcon: max8997: Use workqueue to check cable state after completing boot of platform
extcon: max8997: Set default UART/USB path on probe
extcon: max8997: Consolidate duplicate code for checking ADC/CHG cable type
extcon: max8997: Set default of ADC debounce time during initialization
extcon: max8997: Remove duplicate code related to set H/W line path
extcon: max8997: Move defined constant to header file
extcon: max77693: Make max77693_extcon_cable static
extcon: max8997: Remove unreachable code
extcon: max8997: Make max8997_extcon_cable static
extcon: max77693: Remove unnecessary goto statement to improve readability
extcon: max77693: Convert to devm_input_allocate_device()
extcon: gpio: Rename filename of extcon-gpio.c according to kernel naming style
CREDITS: update email and address of Harald Hoyer
extcon: arizona: Use MICDET for final microphone identification
extcon: arizona: Always take the first HPDET reading as the final one
extcon: arizona: Clear _trig_sts bits after jack detection
extcon: arizona: Don't HPDET magic when headphones are enabled
...
This patch use delayed workqueue to check cable state after a certain
time. If extcon-max8997 driver check cable state during booting of
platform, this couldn't send the correct notification of cable state
to extcon consumer. Alwasys, this driver should check cable state
after the completion of platform initialization
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch set default H/W line path according to platfomr data.
The MAX8997 MUIC device can possibly set UART/USB or UART_AUX
/USB_AUX to internal H/W line path of MUIC device. Namely, only
one H/W line is used for two operation.
For example,
if H/W line path of MAX8997 device set UART/USB, micro usb cable
is connected to AP(Application Processor) and if H/W line path
set UART_AUX/USB_AUX, micro usb cable is connected to CP(Coprocessor).
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch make max8997_muic_get_cable_type() function to remove
duplicate code for checking ADC/Charger cable type because almost
internal function need to read adc/chg_type value of MUIC register.
Also, remove *_detach() function, extcon-max8997 driver treat
attach/detach operation of cable in max8997_*_handler() function.
Lastly, this patch move defined constant in header file(include/
linux/mfd/max8997.h, max8997-private.h) because defined constant
is only used in the 'extcon-max8997.c'.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch set default of ADC Debounce Time(25ms) during probe step.
Also, can possible change ADC Debounce Time according to H/W situation
by using max8997_set_adc_debounce_time()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch move defined constants to header file(max77693-private.h)
because of mask/unmask selectively interrupt of MUIC device according
to attribute of H/W board.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
'max77693_extcon_cable' is used only in this file. Hence
make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
'break' after 'return' is never executed and hence can be deleted.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
'max8997_extcon_cable' is used only in this file. Hence make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
More updates for v3.9, a mix of fixes for the code that's already there
and a few new features.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=7J4T
-----END PGP SIGNATURE-----
Merge tag 'extcon-arizona-3.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc into char-misc-next
Mark writes:
extcon: arizona: Updates for v3.9
More updates for v3.9, a mix of fixes for the code that's already there
and a few new features.
When using HPDET to identify the accessory still run MICDET before we
report a microphone in order to ensure that the accessory identified is
compatible with the MICDET detection ranges after having confirmed that
the device is not using a headphone.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This should always be the most accurate reading for supported accessory
configurations.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It is important to clear the wake trigger status bits otherwise DCVDD
will be held high independent of the state of the LDOENA line.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The magic is already done as part of enabling the headphone output so
does not need to be done when the headphone outputs are enabled. We hold
the DAPM lock so the headphone status can't be changed underneath us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The HPDET identification method does not have the same natural debounce
built into it that the standard MICDET method does so add some extra on
top of what the jack detection does in hardware to make sure we get a
robust result.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When starting microphone detection some headsets should be exposed to
the fully regulated microphone bias in order to ensure that they behave
in an optimal fashion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow systems to tune detection rate and debounce suitably for their
mechanical parameters.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For iio_channel_get to work with OF based configurations, it needs the
consumer device pointer instead of the consumer device name as argument.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Anton Vorontsov <anton@enomsg.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch fix build error of following log:
drivers/built-in.o: In function `max77693_muic_remove':
extcon-max77693.c:(.text+0x664853): undefined reference to `input_unregister_device'
drivers/built-in.o: In function `max77693_muic_probe':
extcon-max77693.c:(.text+0x664971): undefined reference to `input_allocate_device'
extcon-max77693.c:(.text+0x6649c1): undefined reference to `input_set_capability'
extcon-max77693.c:(.text+0x6649d6): undefined reference to `input_set_capability'
extcon-max77693.c:(.text+0x6649eb): undefined reference to `input_set_capability'
extcon-max77693.c:(.text+0x664a00): undefined reference to `input_set_capability'
extcon-max77693.c:(.text+0x664a15): undefined reference to `input_set_capability'
extcon-max77693.c:(.text+0x664a20): undefined reference to `input_register_device'
drivers/built-in.o: In function `max77693_muic_adc_handler':
extcon-max77693.c:(.text+0x665318): undefined reference to `input_event'
extcon-max77693.c:(.text+0x66532a): undefined reference to `input_event'
make[1]: *** [vmlinux] Error 1
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We now have mechanisms in place to allow retries so let's use them rather
than guessing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure we clamp as quickly as possible after removal by disabling the
debounce while there is an accessory present.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With some GPIO control it is possible to detect microphones in a wider
range of configurations by directly measuring the microphone impedance
when the HPDET method cannot distinguish between the behaviour of the
two grounds. Allow a GPIO to be provided in platform data and use it to
implement this behaviour.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
The accessory detection functionality in Arizona devices is flexible and
supports several system designs in addition to the default one implemented
by the existing driver. One such design uses the HPDET feature to determine
what kind of accessory is present by comparing measurements taken with the
two headphone grounds available on the device, implement that if selected
by platform data.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Use the headphone detection to identify if the accessory is a headphone or
line load. There are two different revisions of the IP with different
register layouts, support both.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Some system designs provide an input on GPIO5 which in conjunction with
the jack detection feature indicates the presence of an accessory.
Support such systems, using the microphone clamp feature to minimise
wakeups of the processor.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Newer Arizona devices include a microphone clamp function which is tied to
jack detect. Activate this feature when present in order to ensure best
performance of the subsystem.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Allow configuration of the rise time for MICBIAS via platform data, the
delay required depends on things like the external component selection.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The micd_pol GPIO is only requested if we've specified one greater than 0
so apply the same test before we set it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Now this is configured by platform data remove the defualt configuration
the driver had.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch support the detection of Dock-Smart device which include
three type of port(HDMI, USB for mouse/keyboard and Micro-USB for
USB/TA cable).The Dock-Smart device need always exteranl power supply
(USB/TA cable through micro-usb cable). Dock-Smart device support screen
output of target to separate monitor and mouse/keyboard for desktop
mode.
Features of 'Dock-Smart device'
- Support HDMI
- Support external output feature of audio
- Support charging through micro-usb port without data
connection if TA cable is connected to target.
- Support charging and data connection through micro-usb port
if USB cable is connected between target and host device.
- Support OTG device (Mouse/Keyboard)
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch fix bug that muic couldn't detect MHL/Dock-Audio with USB/TA
cable on exception situation. I explain detail case on following:
When MHL(with USB/TA cable) or Dock-Audio with USB/TA cable is attached,
the MUIC device happen following two interrupt.
- 'MAX77693_MUIC_IRQ_INT1_ADC' for detecting MHL/Dock-Audio.
- 'MAX77693_MUIC_IRQ_INT2_CHGTYP' for detecting USB/TA cable connected to
MHL/Dock-Audio. Always, happen eariler MAX77693_MUIC_IRQ_INT1_ADC interrupt
than MAX77693_MUIC_IRQ_INT2_CHGTYP interrupt.
If user attach MHL with USB/TA cable and immediately detach MHL with USB/TA
cable before MAX77693_MUIC_IRQ_INT2_CHGTYP interrupt is happened, USB/TA
connected to MHL cable remain connected state to target. But USB/TA connected
to MHL cable isn't connected to target. user be faced with unusual action.
So, driver should check this situation in spite of that, previous charger type
is N/A.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch determine default uart/usb path by using platform data.
The MAX77693 MUIC device can possibliy set USB/UART/AUDIO/USB_AUX
/UART_AUX to internal h/w path of MUIC device. So, drvier should
determine default uart/usb path.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch check the state/type of cable after completing the initialization
of platform and notify platform of cable state/type through extcon. If extcon
provider driver notify the state/type of cable before completing platform boot,
this uevent is unused and ignored.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch support detection of dock device with extcon and
buttons of dock device for playing music with input subsystem.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch detect several kinds of JIG cable according to ADC value
and set the hardware line path according to type of JIG cable(JIG-USB-ON
/JIG-USB-OFF/JIG-UART-OFF).
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch support MHL_TA cable for charging battery. The MHL_TA
cable include MHL with TA cable or MHL with micro USB cable. When
MHL with TA/USB cable is attached, extcon-max77693 driver detect
two interrupt for handling precise operation according to each cable
(MHL and TA/USB cable).
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This patch make max77693-muic_get_cable_type() function to remove
duplicate code because almost internal function need to read
adc/adc1k/adclow/chg_type value of MUIC register. Also, this patch
add description of internal function move field constant of muic device
from extcon-max77693 driver to max77693 header file because of it
is needed for masking some interrupt through platform data.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
This is based on Linux 3.7 rc6
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/KTt
-----END PGP SIGNATURE-----
Merge tag 'pull_req_20121122' of git://git.kernel.org/pub/scm/linux/kernel/git/mzx/extcon into char-misc-next
MyungJoo writes:
"extcon pull request targetting Linux 3.8 for Greg KH on 2012.11.22
This is based on Linux 3.7 rc6"
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
devm_kzalloc() is a device managed function. It makes error handling
and cleanup code a bit simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
devm_kzalloc() is a device managed function. It makes error handling
and cleanup code a bit simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Fixes the following checkpatch error:
ERROR: space required after that ',' (ctx:VxV)
460: FILE: extcon/extcon-max8997.c:460:
ret = request_threaded_irq(virq, NULL,max8997_muic_irq_handler,
^
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
As per kernel coding style, if one branch of conditional statement has braces,
the other one should have too.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
irq_create_mapping() returns 0 if it fails to provide a valid irq number.
'ret' needs to be updated with a negative error code before returning from
probe to signal probe failure. While at it, also corrected the 'virq' type to
unsigned from signed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
irq_create_mapping() returns 0 if it fails to provide a valid irq number.
'ret' needs to be updated with a negative error code before returning from
probe to signal probe failure. While at it, also corrected the 'virq' type to
unsigned from signed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Return the value obtained from the function extcon_register_interest
instead of -ENODEV.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
If regmap_read() failed, arizona_micdet() returns IRQ_NONE
leaving &info->lock mutex locked as opposed to all other return paths.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
There are some scnearios where a driver/framework needs to register
interest for a particular cable without specifying the extcon device
name. One such scenario is charger notifications. The platform will
have charger cabel which will be bound to any extcon device. It's
not mandatory for the charger driver to know which extcon device
it should use. This patch enables the support for registering
interest for a cable just by cable name wihtout specifying the
extcon device name
Signed-off-by: Jenny TC <jenny.tc@intel.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
--
Kernel-doc comment added by MyungJoo Ham
Extcon core doesn't free the memory when we do unregister.
Kfree is added in the remove path as it was missing.
Signed-off-by: anish kumar <anish198519851985@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There was a case where free and list_del can be called twice
on the same pointer.So fixed it by re-arranging the code and
removing a function which was not needed.
Signed-off-by: anish kumar <anish198519851985@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch add platform data for MUIC device to initialize register
on probe() call because it should unmask interrupt mask register
and initialize some register related to MUIC device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This driver can be built as a module, add MODULE_LICENSE for it.
For completeness, also adds MODULE_AUTHOR and MODULE_DESCRIPTION.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
On failure, request_any_context_irq() returns a negative value.
On success, it returns either IRQC_IS_HARDIRQ or IRQC_IS_NESTED.
Also ensure adc_jack_probe() return 0 on success.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Propagate the value returned from extcon_find_cable_index()
instead of -ENODEV. For readability, -EINVAL is returned in place of
the variable.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Since extcon registers this compat link at device registration
(extcon_dev_register), we should probably remove them at deregistration/cleanup.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Rather than re-inventing the wheel we can use the hamming function
to calculate the number of bits set to check for violation of
exclusivity.
Signed-off-by: anish kumar <anish198519851985@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
With this change now individual drivers can use standard cable
names as below:
static const char *arizona_cable[] = {
extcon_cable_name[EXTCON_USB],
extcon_cable_name[EXTCON_USB_HOST],
"CUSTOM_CABLE"
NULL,
}
Signed-off-by: anish kumar <anish198519851985@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
actually we can do returns with error or success with out ret in this function,
so remove the ret variable, and reduce a very little (4byte) space on stack of this function
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
Here is the big driver core update for 3.7-rc1.
A number of firmware_class.c updates (as you saw a month or so ago), and
some hyper-v updates and some printk fixes as well. All patches that
are outside of the drivers/base area have been acked by the respective
maintainers, and have all been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlBp3vkACgkQMUfUDdst+ylQoACgldktGFgkCLzH+rGYthrXOC5P
9hUAnjmOhdoHlMTL81vWTlH+BrGernym
=khrr
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core merge from Greg Kroah-Hartman:
"Here is the big driver core update for 3.7-rc1.
A number of firmware_class.c updates (as you saw a month or so ago),
and some hyper-v updates and some printk fixes as well. All patches
that are outside of the drivers/base area have been acked by the
respective maintainers, and have all been in the linux-next tree for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (95 commits)
memory: tegra{20,30}-mc: Fix reading incorrect register in mc_readl()
device.h: Add missing inline to #ifndef CONFIG_PRINTK dev_vprintk_emit
memory: emif: Add ifdef CONFIG_DEBUG_FS guard for emif_debugfs_[init|exit]
Documentation: Fixes some translation error in Documentation/zh_CN/gpio.txt
Documentation: Remove 3 byte redundant code at the head of the Documentation/zh_CN/arm/booting
Documentation: Chinese translation of Documentation/video4linux/omap3isp.txt
device and dynamic_debug: Use dev_vprintk_emit and dev_printk_emit
dev: Add dev_vprintk_emit and dev_printk_emit
netdev_printk/netif_printk: Remove a superfluous logging colon
netdev_printk/dynamic_netdev_dbg: Directly call printk_emit
dev_dbg/dynamic_debug: Update to use printk_emit, optimize stack
driver-core: Shut up dev_dbg_reatelimited() without DEBUG
tools/hv: Parse /etc/os-release
tools/hv: Check for read/write errors
tools/hv: Fix exit() error code
tools/hv: Fix file handle leak
Tools: hv: Implement the KVP verb - KVP_OP_GET_IP_INFO
Tools: hv: Rename the function kvp_get_ip_address()
Tools: hv: Implement the KVP verb - KVP_OP_SET_IP_INFO
Tools: hv: Add an example script to configure an interface
...
- A tps65217 build error fix.
- A lcp_ich regression fix caused by the MFD driver failing to initialize the
watchdog sub device due to ACPI conflicts.
- 2 MAX77693 interrupt handling bug fixes.
- An MFD core fix, adding an IRQ domain argument to the MFD device addition
API in order to prevent silent and potentially harmful remapping behaviour
changes for drivers supporting non-DT platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=nP/y
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull mfd fixes from Samuel Ortiz:
"This is the remaining MFD fixes for 3.6, with 5 pending fixes:
- A tps65217 build error fix.
- A lcp_ich regression fix caused by the MFD driver failing to
initialize the watchdog sub device due to ACPI conflicts.
- 2 MAX77693 interrupt handling bug fixes.
- An MFD core fix, adding an IRQ domain argument to the MFD device
addition API in order to prevent silent and potentially harmful
remapping behaviour changes for drivers supporting non-DT
platforms."
* tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: MAX77693: Fix NULL pointer error when initializing irqs
mfd: MAX77693: Fix interrupt handling bug
mfd: core: Push irqdomain mapping out into devices
mfd: lpc_ich: Fix a 3.5 kernel regression for iTCO_wdt driver
mfd: Move tps65217 regulator plat data handling to regulator
This patch initialize register map of MUIC device because mfd driver
of Maxim MAX77693 use regmap-muic instance of MUIC device when irqs of
Maxim MAX77693 is initialized before call max77693-muic probe() function.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reported-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
We can perform microphone detection with MICVDD in bypass mode so try to
enable that during startup for minimal power - other users or machine
constraints will prevent bypass mode being activated if it is unsuitable.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci
Make sure threaded IRQs without a primary handler are always
requested with IRQF_ONESHOT.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
External connector devices that decides connection information based on
ADC values may use adc-jack device driver. The user simply needs to
provide a table of adc range and connection states. Then, extcon
framework will automatically notify others.
Changes in V1:
added Lars-Peter Clausen suggested changes:
Using macros to get rid of boiler plate code such as devm_kzalloc
and module_platform_driver.Other changes suggested are related to
coding guidelines.
Changes in V2:
Removed some unnecessary checks and changed the way we are un-regitering
extcon and freeing the irq while removing.
Changes in V3:
Renamed the files to comply with extcon naming.
Changes in V4:
Added the cancel_work_sync during removing of driver.
Changes in V5:
Added the dependency of IIO in Kconfig.
Changes in V6:
Some nitpicks related to naming.
Changes in this version:
V6 patch version patch broke the build:
ERROR: "extcon_cable_name" [drivers/extcon/extcon-adc-jack.ko] undefined!
Fixed it in this version.
Acked-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: anish kumar <anish.singh@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The operation of lockdep requires that all dynamically allocated sysfs
nodes are initialised using sysfs_attr_init() otherwise lots of warnings
are generated. Ensure that all the dynamically allocated attributes that
extcon generates have this done.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replaced '_' with '-' in the extcon file names, which has been bogging
since new drivers have been using the standard naming.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 980d792981 as it
breaks the build with the error:
ERROR: "extcon_cable_name" [drivers/extcon/extcon-adc-jack.ko] undefined!
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: anish kumar <anish.singh@samsung.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
External connector devices that decides connection information based on
ADC values may use adc-jack device driver. The user simply needs to
provide a table of adc range and connection states. Then, extcon
framework will automatically notify others.
Changes in V1:
added Lars-Peter Clausen suggested changes:
Using macros to get rid of boiler plate code such as devm_kzalloc
and module_platform_driver.Other changes suggested are related to
coding guidelines.
Changes in V2:
Removed some unnecessary checks and changed the way we are un-regitering
extcon and freeing the irq while removing.
Changes in V3:
Renamed the files to comply with extcon naming.
Changes in V4:
Added the cancel_work_sync during removing of driver.
Changes in V5:
Added the dependency of IIO in Kconfig.
Changes in V6:
Some nitpicks related to naming.
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: anish kumar <anish.singh@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As well as identifying accessories the accessory detection hardware on
Arizona class devices can also detect a number of buttons which we should
report via the input API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01eaf24 "extcon: Convert extcon_gpio to devm_gpio_request_one"
missed the replacement for devm_gpio_request_one. fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQFpGVAAoJEIqAPN1PVmxKFNoP/1dkYngrxxV6cxdyLJ74APhG
lVKPgaDxQhdgfwCZJmMeZK1UphZo80cWnEXG6sTHZUEQdTaslSJu5SuPfUM+fo7e
52/dU0nx0ZE04pwPQLHbidS4TmHlbLg9oM2kmIf9RO5rg34GodwVgRL/4+k1qvhz
aWYJt9erFhQOpqaSX66mXHSuhvzHypbcE7d2B2Ykmh3NoYiH2w9H9KmIbbb+ZLq8
+Bp/i5Ys/vfooo+8IE2w6KZfIzMwsmmtWjjr/38yuQJaKZCh/zn23DM9HsdrVf++
RzfniRF4YBxmeKi7zi8MFIYys8filTCXA9dXbGSAKCuUCT37yZRnUxTeN1bn7Bux
A7KRpG7pUKQKVKqCTndvK5LcQKlT33XyW2ZzV1wVWX2JkCJ+gilPeykb8IabNvGX
nIp0STEGR/WdCLEAKo8pJF7Usn0RuUzAug02SG/mQ6dpnLoZqp0Od5W7gRhT7M7h
hXr/xKJ6cG5YwicpAdy5kJJ0dRgQrtaHwxrF0B68AXZ7CmAtkPuEGCYhUCFnGQUH
XJ0CodAqqVBRyYiQS4zIpIh2nqhIdsgv4OC1+kVLbubQk+PR88zG9Jvg6i1HQi/A
OHi7N5Wite3YUrs3sBzDKnEc/Il2YRhVaz2SLVNfZR0PS7hywHN3rK/tVFINTgei
jNEz1H6hu7ToNLfs0UzP
=c28c
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD bits from Samuel Ortiz:
"We have support for a few new drivers:
- Samsung s2mps11
- Wolfson Microelectronics wm5102 and wm5110
- Marvell 88PM800 and 88PM805
- TI twl6041
We also have our regular driver improvements:
- Device tree and IRQ domain support for STE AB8500
- Regmap and devm_* API conversion for TI tps6586x
- Device tree support for Samsung max77686
- devm_* API conversion for STE AB3100
Besides that, quite a lot of fixing and cleanup for mc13xxx, tps65910,
tps65090, da9052 and twl-core."
Fix up mostly trivial conflicts, with the exception of
drivers/usb/host/ehci-omap.c in particular, which had some
re-organization of the reset sequence (commit 1a49e2ac96: "EHCI:
centralize controller initialization") that clashed with commit
2761a63945 ("mfd: USB: Fix the omap-usb EHCI ULPI PHY reset fix
issues").
In particular, commit 2761a63945 moved the usb_add_hcd() to the
*middle* of the reset sequence, which clashes fairly badly with the
reset sequence re-organization (although it could have been done inside
the new omap_ehci_init() function).
I left that part of commit 2761a63945 just undone.
* tag 'mfd-3.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (110 commits)
mfd: Ensure AB8500 platform data is passed through db8500-prcmu to MFD Core
mfd: Arizone core should select MFD_CORE
mfd: Fix arizona-irq.c build by selecting REGMAP_IRQ
mfd: Add debug trace on entering and leaving arizone runtime suspend
mfd: Correct tps65090 cell names
mfd: Remove gpio support from tps6586x core driver
ARM: tegra: defconfig: Enable tps6586x gpio
gpio: tps6586x: Add gpio support through platform driver
mfd: Cache tps6586x register through regmap
mfd: Use regmap for tps6586x register access.
mfd: Use devm managed resources for tps6586x
input: Add onkey support for 88PM80X PMIC
mfd: Add support for twl6041
mfd: Fix twl6040 revision information
mfd: Matches should be NULL when populate anatop child devices
input: ab8500-ponkey: Create AB8500 domain IRQ mapping
mfd: Add missing out of memory check for pcf50633
Documentation: Describe the AB8500 Device Tree bindings
mfd: Add tps65910 32-kHz-crystal-input init
mfd: Drop modifying mc13xxx driver's id_table in probe
...
This patch support Maxim MAX77693 MUIC device by using EXTCON Subsystem
to handle various external connector. The extcon-max77693 use regmap
method for i2c communication and support irq domain instead of previous
method of irq base.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There should be no point in continuing to try to detect a microphone any
more so stop doing so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use extcon_set_state_ for performance and split the headset into separate
headphone and microphone reports as this is more idiomatic.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add support irq domain for Maxim MAX8997 muic
instead of irq_base in platform data and max8997 driver
private data are instead. It is tested on TRATS board.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This picks up the big printk fixes, and resolves a merge issue with:
drivers/extcon/extcon_gpio.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most Wolfson Arizona class audio hub CODECs include a flexible ultra low
power accessory detection subsystem. This driver exposes initial support
for this subsystem via the Extcon framework, implementing support for
ultra low power detection of headphone and headset with the ability to
detect the polarity of a headset.
The functionality of the devices is much richer and more flexible than
the current driver, future patches will extend the features of the
driver to more fully exploit this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing platform_set_drvdata() in gpio_extcon_probe(), otherwise calling
platform_get_drvdata in gpio_extcon_remove() returns NULL.
Also add missing free_irq call in gpio_extcon_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
extcon_dev_unregister(info->edev) doest not free info->edev, we need to call
kfree(info->edev) here.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add missing platform_set_drvdata() in gpio_extcon_probe(), otherwise calling
platform_get_drvdata in gpio_extcon_remove() returns NULL.
Also add missing free_irq call in gpio_extcon_remove().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the index of "Dock-desk" and "Dock-card" are the same.
Thus the latter one overrides the first one.
Then we have problem when calling extcon_find_cable_index() because
edev->supported_cable[7] only matches "Dock-card".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can't create a link from the device to the compatibility switch class
since we already create a link from the device to to the extcon class
object and we try to use the same name for both links. This causes a loud
complaint from sysfs on boot.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's not referenced outside the core file.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging switch
driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7q28ACgkQMUfUDdst+ykXmwCfcPASzC+/bDkuqdWsqzxlWZ7+
VOQAnAriySv397St36J6Hz5bMQZwB1Yq
=SQc+
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging
switch driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up conflicts in drivers/extcon/extcon-max8997.c where git noticed
that a patch to the deleted drivers/misc/max8997-muic.c driver needs to
be applied to this one.
* tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (90 commits)
uio_pdrv_genirq: get irq through platform resource if not set otherwise
memory: tegra{20,30}-mc: Remove empty *_remove()
printk() - isolate KERN_CONT users from ordinary complete lines
sysfs: get rid of some lockdep false positives
Drivers: hv: util: Properly handle version negotiations.
Drivers: hv: Get rid of an unnecessary check in vmbus_prep_negotiate_resp()
memory: tegra{20,30}-mc: Use dev_err_ratelimited()
driver core: Add dev_*_ratelimited() family
Driver Core: don't oops with unregistered driver in driver_find_device()
printk() - restore prefix/timestamp printing for multi-newline strings
printk: add stub for prepend_timestamp()
ARM: tegra30: Make MC optional in Kconfig
ARM: tegra20: Make MC optional in Kconfig
ARM: tegra30: MC: Remove unnecessary BUG*()
ARM: tegra20: MC: Remove unnecessary BUG*()
printk: correctly align __log_buf
ARM: tegra30: Add Tegra Memory Controller(MC) driver
ARM: tegra20: Add Tegra Memory Controller(MC) driver
printk() - restore timestamp printing at console output
printk() - do not merge continuation lines of different threads
...
This patch add extcon-max8997 driver to support the muic feature
of Maxim max8997 by using Extcon framework.
The extcon-max8997 driver is implemented based on 'drivers/misc/
max8997-muic.c' and then use Extcon interface instead of callback
function in struct max8997_muic_platform_data to notify cable state
of notifee which want to know always newly cable state when external
connector(e.g., USB, TA, JIG) is attached or detached.
v1
- Use Extcon interface to notify cable state of notifee instead of
callback function when external connector is attached or detached.
- Bug fix of getting platform_data for irq_base value.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some accessory detection mechanisms are able to detect that something is
physically present in the socket separately to identifying what is present
in the socket. This information can be useful to applications, for example
allowing them to indicate that a potentially broken accessory is present,
so provide a standard way to report it to userspace.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the section mismatch be renaming the struct platform_driver
variable.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch inform the state of only one cable instead of previous data
including the state of 32 cables to notifee which use
extcon_register_interest()
function to monitor whether the specific cable is attachd or detached.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Myungjoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return -ENOMEM if the kmalloc() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because extcon can also be a switch class for legacy userspace (Android)
and is a superset of switch class in drivers/staging/android/switch,
switch class may be removed.
- Remove switch class
- Remove switch class consideration in extcon class
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There could be cables that t recannot be attaches simulatenously. Extcon
device drivers may express such information via mutually_exclusive in
struct extcon_dev.
For example, for an extcon device with 16 cables (bits 0 to 15 are
available), if mutually_exclusive = { 0x7, 0xC0, 0x81, 0 }, then, the
following attachments are prohibitted.
{0, 1}
{0, 2}
{1, 2}
{6, 7}
{0, 7}
and every attachment set that are superset of one of the above.
For the detail, please refer to linux/include/linux/extcon.h.
The concept is suggested by NeilBrown <neilb@suse.de>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
--
Changes from V5:
- Updated sysfs format
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
One switch device (e.g., MUIC(MAX8997, MAX77686, ...), and some 30-pin
devices) may have multiple cables attached. For example, one
30-pin port may inhabit a USB cable, an HDMI cable, and a mic.
Thus, one switch device requires multiple state bits each representing
a type of cable.
For such purpose, we use the 32bit state variable; thus, up to 32
different type of cables may be defined for a switch device. The list of
possible cables is defined by the array of cable names in the switch_dev
struct given to the class.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
--
Changes from V7
- Bugfixed in _call_per_cable() (incorrect nb) (Chanwoo Choi)
- Compiler error in header for !CONFIG_EXTCON (Chanwoo Choi)
Changes from V5
- Sysfs style reformed: subdirectory per cable.
- Updated standard cable names
- Removed unnecessary printf
- Bugfixes after testing
Changes from V4
- Bugfixes after more testing at Exynos4412 boards with userspace
processses.
Changes from V3
- Bugfixes after more testing at Exynos4412 boards.
Changes from V2
- State can be stored by user
- Documentation updated
Changes from RFC
- Switch is renamed to extcon
- Added kerneldoc comments
- Added APIs to support "standard" cable names
- Added helper APIs to support notifier block registration with cable
name.
- Regrouped function list in the header file.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
State changes of extcon devices have been notified via kobjet_uevent.
This patch adds notifier interfaces in order to allow device drivers to
get notified easily. Along with notifier interface,
extcon_get_extcon_dev() function is added so that device drivers may
discover a extcon_dev easily.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
Changes from RFC
- Renamed switch to extcon
- Bugfix: extcon_dev_unregister()
- Bugfix: "edev->dev" is "internal" data.
- Added kerneldoc comments.
- Reworded comments.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The generic GPIO extcon driver (an external connector device based on
GPIO control) and imported from Android kernel.
switch: switch class and GPIO drivers. (splitted)
Author: Mike Lockwood <lockwood@android.com>
switch: gpio: Don't call request_irq with interrupts disabled
Author: Arve Hjønnevåg <arve@android.com>
switch_gpio: Add missing #include <linux/interrupt.h>
Author: Mike Lockwood <lockwood@android.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
Changed from v7:
- Style updates mentioned by Stephen Boyd and Mark Brown
Changed from v5:
- Splitted at v5 from the main extcon patch.
- Added debounce time for irq handlers.
- Use request_any_context_irq instead of request_irq
- User needs to specify irq flags for GPIO interrupts (was fixed to
IRQF_TRIGGER_LOW before)
- Use module_platform_driver().
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
External connector class (extcon) is based on and an extension of
Android kernel's switch class located at linux/drivers/switch/.
This patch provides the before-extension switch class moved to the
location where the extcon will be located (linux/drivers/extcon/) and
updates to handle class properly.
The before-extension class, switch class of Android kernel, commits
imported are:
switch: switch class and GPIO drivers. (splitted)
Author: Mike Lockwood <lockwood@android.com>
switch: Use device_create instead of device_create_drvdata.
Author: Arve Hjønnevåg <arve@android.com>
In this patch, upon the commits of Android kernel, we have added:
- Relocated and renamed for extcon.
- Comments, module name, and author information are updated
- Code clean for successing patches
- Bugfix: enabling write access without write functions
- Class/device/sysfs create/remove handling
- Added comments about uevents
- Format changes for extcon_dev_register() to have a parent dev.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
--
Changes from v7
- Compiler error fixed when it is compiled as a module.
- Removed out-of-date Kconfig entry
Changes from v6
- Updated comment/strings
- Revised "Android-compatible" mode.
* Automatically activated if CONFIG_ANDROID && !CONFIG_ANDROID_SWITCH
* Creates /sys/class/switch/*, which is a copy of /sys/class/extcon/*
Changes from v5
- Split the patch
- Style fixes
- "Android-compatible" mode is enabled by Kconfig option.
Changes from v2
- Updated name_show
- Sysfs entries are handled by class itself.
- Updated the method to add/remove devices for the class
- Comments on uevent send
- Able to become a module
- Compatible with Android platform
Changes from RFC
- Renamed to extcon (external connector) from multistate switch
- Added a seperated directory (drivers/extcon)
- Added kerneldoc comments
- Removed unused variables from extcon_gpio.c
- Added ABI Documentation.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
