on driver load, if reset_devices is set, and the hard reset
attempts fail, try to bring up the controller to the point that
a command can be sent, and send it a soft reset command, then
after the reset undo whatever driver initialization was done to get
it to the point to take a command, and re-do it after the reset.
This is to get kdump to work on all the "non-resettable" controllers
(except 64xx controllers which can't be reset due to the potentially
shared cache module.)
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The bit-2-doorbell reset method seemed to cause (survivable) NMIs
on some systems and (unsurvivable) IOCK NMIs on some G7 servers.
Firmware guys implemented a new doorbell method to alleviate these
problems triggered by bit 5 of the doorbell register. We want to
use it if it's available.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Just to reduce the messages about timeouts that appear.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
When waiting for the board to become "not ready"
don't print a message saying "waiting for board to
become ready" (possibly followed by a message saying
"failed waiting for board to become not ready". Instead,
it should be "waiting for board to reset" and "failed
waiting for board to reset."
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
"
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Detect failure of controller reset by noticing if the 32 bytes of
"driver version" we store on the hardware in the config table
fail to get zeroed out. Previously we noticed if the controller
did not transition to "simple mode", but this did not detect reset
failure if the controller was already in simple mode prior to
the reset attempt (e.g. due to module parameter hpsa_simple_mode=1).
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This is to ensure the board interrupts are really off when
these functions return.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Disk event code automatically blocks events on excl write. This is
primarily to avoid issuing polling commands while burning is in
progress. This behavior doesn't fit other types of devices with
removeable media where polling commands don't have adverse side
effects and door locking usually doesn't exist.
This patch introduces new genhd flag which controls the auto-blocking
behavior and uses it to enable auto-blocking only on optical devices.
Note for stable: 2.6.38 and later only
Cc: stable@kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In commit 95a0f10cdd ("drbd: store in-core bitmap little endian,
regardless of architecture") drbd had made the sane choice to use
little-endian bitmap functions everywhere. However, it used the
horrible old functions names from <asm-generic/bitops/le.h>, that were
never really meant to be exported.
In the meantime, things got cleaned up, and in commit c4945b9ed4
("asm-generic: rename generic little-endian bitops functions") we
renamed the LE bitops to something sane, exactly so that they could be
used in random code without people gouging their eyes out when seeing
the crazy jumble of letters that were the old internal names.
As a result the drbd thing merged cleanly (commit 8d49a77568: "Merge
branch 'for-2.6.39/drivers' of git://git.kernel.dk/linux-2.6-block"),
since there was no data conflict - but the end result obviously doesn't
actually compile.
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-2.6.39/drivers' of git://git.kernel.dk/linux-2.6-block: (122 commits)
cciss: fix lost command issue
drbd: need include for bitops functions declarations
Revert "cciss: Add missing allocation in scsi_cmd_stack_setup and corresponding deallocation"
cciss: fix missed command status value CMD_UNABORTABLE
cciss: remove unnecessary casts
cciss: Mask off error bits of c->busaddr in cmd_special_free when calling pci_free_consistent
cciss: Inform controller we are using 32-bit tags.
cciss: hoist tag masking out of loop
cciss: Add missing allocation in scsi_cmd_stack_setup and corresponding deallocation
cciss: export resettable host attribute
drbd: drop code present under #ifdef which is relevant to 2.6.28 and below
drbd: Fixed handling of read errors on a 'VerifyS' node
drbd: Fixed handling of read errors on a 'VerifyT' node
drbd: Implemented real timeout checking for request processing time
drbd: Remove unused function atodb_endio()
drbd: improve log message if received sector offset exceeds local capacity
drbd: kill dead code
drbd: don't BUG_ON, if bio_add_page of a single page to an empty bio fails
drbd: Removed left over, now wrong comments
drbd: serialize admin requests for new verify run with pending bitmap io
...
* 'for-2.6.39/core' of git://git.kernel.dk/linux-2.6-block: (65 commits)
Documentation/iostats.txt: bit-size reference etc.
cfq-iosched: removing unnecessary think time checking
cfq-iosched: Don't clear queue stats when preempt.
blk-throttle: Reset group slice when limits are changed
blk-cgroup: Only give unaccounted_time under debug
cfq-iosched: Don't set active queue in preempt
block: fix non-atomic access to genhd inflight structures
block: attempt to merge with existing requests on plug flush
block: NULL dereference on error path in __blkdev_get()
cfq-iosched: Don't update group weights when on service tree
fs: assign sb->s_bdi to default_backing_dev_info if the bdi is going away
block: Require subsystems to explicitly allocate bio_set integrity mempool
jbd2: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
jbd: finish conversion from WRITE_SYNC_PLUG to WRITE_SYNC and explicit plugging
fs: make fsync_buffers_list() plug
mm: make generic_writepages() use plugging
blk-cgroup: Add unaccounted time to timeslice_used.
block: fixup plugging stubs for !CONFIG_BLOCK
block: remove obsolete comments for blkdev_issue_zeroout.
blktrace: Use rq->cmd_flags directly in blk_add_trace_rq.
...
Fix up conflicts in fs/{aio.c,super.c}
Under certain workloads a command may seem to get lost. IOW, the Smart Array
thinks all commands have been completed but we still have commands in our
completion queue. This may lead to system instability, filesystems going
read-only, or even panics depending on the affected filesystem. We add an
extra read to force the write to complete.
Testing shows this extra read avoids the problem.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use watch/notify for changes in rbd header
libceph: add lingering request and watch/notify event framework
rbd: update email address in Documentation
ceph: rename dentry_release -> d_release, fix comment
ceph: add request to the tail of unsafe write list
ceph: remove request from unsafe list if it is canceled/timed out
ceph: move readahead default to fs/ceph from libceph
ceph: add ino32 mount option
ceph: update common header files
ceph: remove debugfs debug cruft
libceph: fix osd request queuing on osdmap updates
ceph: preserve I_COMPLETE across rename
libceph: Fix base64-decoding when input ends in newline.
Send notifications when we change the rbd header (e.g. create a snapshot)
and wait for such notifications. This allows synchronizing the snapshot
creation between different rbd clients/rools.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Sage Weil <sage@newdream.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (47 commits)
doc: CONFIG_UNEVICTABLE_LRU doesn't exist anymore
Update cpuset info & webiste for cgroups
dcdbas: force SMI to happen when expected
arch/arm/Kconfig: remove one to many l's in the word.
asm-generic/user.h: Fix spelling in comment
drm: fix printk typo 'sracth'
Remove one to many n's in a word
Documentation/filesystems/romfs.txt: fixing link to genromfs
drivers:scsi Change printk typo initate -> initiate
serial, pch uart: Remove duplicate inclusion of linux/pci.h header
fs/eventpoll.c: fix spelling
mm: Fix out-of-date comments which refers non-existent functions
drm: Fix printk typo 'failled'
coh901318.c: Change initate to initiate.
mbox-db5500.c Change initate to initiate.
edac: correct i82975x error-info reported
edac: correct i82975x mci initialisation
edac: correct commented info
fs: update comments to point correct document
target: remove duplicate include of target/target_core_device.h from drivers/target/target_core_hba.c
...
Trivial conflict in fs/eventpoll.c (spelling vs addition)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k/block: amiflop - Remove superfluous amiga_chip_alloc() cast
m68k/atari: ARAnyM - Add support for network access
m68k/atari: ARAnyM - Add support for console access
m68k/atari: ARAnyM - Add support for block access
m68k/atari: Initial ARAnyM support
m68k: Kconfig - Remove unneeded "default n"
m68k: Makefiles - Change to new flags variables
m68k/amiga: Reclaim Chip RAM for PPC exception handlers
m68k: Allow all kernel traps to be handled via exception fixups
m68k: Use base_trap_init() to initialize vectors
m68k: Add helper function handle_kernel_fault()
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1480 commits)
bonding: enable netpoll without checking link status
xfrm: Refcount destination entry on xfrm_lookup
net: introduce rx_handler results and logic around that
bonding: get rid of IFF_SLAVE_INACTIVE netdev->priv_flag
bonding: wrap slave state work
net: get rid of multiple bond-related netdevice->priv_flags
bonding: register slave pointer for rx_handler
be2net: Bump up the version number
be2net: Copyright notice change. Update to Emulex instead of ServerEngines
e1000e: fix kconfig for crc32 dependency
netfilter ebtables: fix xt_AUDIT to work with ebtables
xen network backend driver
bonding: Improve syslog message at device creation time
bonding: Call netif_carrier_off after register_netdevice
bonding: Incorrect TX queue offset
net_sched: fix ip_tos2prio
xfrm: fix __xfrm_route_forward()
be2net: Fix UDP packet detected status in RX compl
Phonet: fix aligned-mode pipe socket buffer header reserve
netxen: support for GbE port settings
...
Fix up conflicts in drivers/staging/brcm80211/brcmsmac/wl_mac80211.c
with the staging updates.
amiga_chip_alloc() returns a void *, so we don't need a cast.
Also clean up coding style while we're at it.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
* 'for-linus' of git://xenbits.xen.org/people/sstabellini/linux-pvhvm:
xen: suspend: remove xen_hvm_suspend
xen: suspend: pull pre/post suspend hooks out into suspend_info
xen: suspend: move arch specific pre/post suspend hooks into generic hooks
xen: suspend: refactor non-arch specific pre/post suspend hooks
xen: suspend: add "arch" to pre/post suspend hooks
xen: suspend: pass extra hypercall argument via suspend_info struct
xen: suspend: refactor cancellation flag into a structure
xen: suspend: use HYPERVISOR_suspend for PVHVM case instead of open coding
xen: switch to new schedop hypercall by default.
xen: use new schedop interface for suspend
xen: do not respond to unknown xenstore control requests
xen: fix compile issue if XEN is enabled but XEN_PVHVM is disabled
xen: PV on HVM: support PV spinlocks and IPIs
xen: make the ballon driver work for hvm domains
xen-blkfront: handle Xen major numbers other than XENVBD
xen: do not use xen_info on HVM, set pv_info name to "Xen HVM"
xen: no need to delay xen_setup_shutdown_event for hvm guests anymore
* 'stable/ia64' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: ia64 build broken due to "xen: switch to new schedop hypercall by default."
* 'stable/blkfront-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: Union the blkif_request request specific fields
* 'stable/cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: annotate functions which only call into __init at start of day
xen p2m: annotate variable which appears unused
xen: events: mark cpu_evtchn_mask_p as __refdata
This reverts commit 978eb516a4.
The commit was broken, relying on other changes that have not been
committed yet.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
and fix a nearby typo, "do" that should have been "due"
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Controller will DMA only 32-bits of the tag per command
on completion if it knows we are only using 32-bit tags.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
In process_nonindexed_cmd, hoist figuring of masked tag out of loop since
it is the same throughout.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This bit got lost somewhere along the way. Without this, panic.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This attribute, requested by Redhat, allows kexec-tools to know
whether the controller can honor the reset_devices kernel parameter
and actually reset the controller. For kdump to work properly it
is necessary that the reset_devices parameter be honored. This
attribute enables kexec-tools to warn the user if they attempt to
designate a non-resettable controller as the dump device.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This code became obsolete and unused last December with
drbd: bitmap keep track of changes vs on-disk bitmap
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Just deal with it more gracefully, if we fail to add even a single page
to an empty bio. We used to BUG_ON() there, but it has been observed in
some Xen deployment, so we need to handle that case more robustly now.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This is an addendum to
drbd: serialize admin requests for new resync with pending bitmap io
It avoids a race that could trigger "FIXME" assert log messages.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When we receive a barrier ack, we walk the ring list of drbd requests
in the transfer log of the respective epoch, do some housekeeping,
and free those objects.
We tried to keep epochs of mirrored and unmirrored drbd requests
separate, and assert that no local-only requests are present in a
barrier_acked epoch.
It turns out that this has quite a number of corner cases and would
add bloated code without functional benefit.
We now revert the (insufficient) commits
drbd: Fixed an issue with AHEAD -> SYNC_SOURCE transitions
drbd: Ensure that an epoch contains only requests of one kind
and instead fix the processing of barrier acks to cope with
a mix of local-only and mirrored requests.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we fail to send the information that we lost our disk,
we have no connection, and no disk: no access to data anymore.
That is either expected (deconfiguration), or there will be so much
noise in the logs that "Sending state failed" is not useful at all.
Drop it.
If the reason for a shorter than expected receive was a signal,
which we sent because we already decided to disconnect,
these additional log messages are confusing and useless.
This patch follows this pattern:
- dev_warn(DEV, "short read expecting header on sock: r=%d\n", r);
+ if (!signal_pending(current))
+ dev_warn(DEV, "short read expecting header on sock: r=%d\n", r);
Also make them all dev_warn for consistency.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now that we do no longer in-place endian-swap the bitmap, we allow
selected bitmap operations (testing bits, sometimes even settting bits)
during some bulk operations.
This caused us to hit a lot of FIXME asserts similar to
FIXME asender in drbd_bm_count_bits,
bitmap locked for 'write from resync_finished' by worker
Which now is nonsense: looking at the bitmap is perfectly legal
as long as it is not being resized.
This cosmetic patch defines some flags to describe expectations in finer
detail, so the asserts in e.g. bm_change_bits_to() can be skipped if
appropriate.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
