Disable interrupts first to prevent spurious WMI events arrival
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connect times out, scan was not re-enabled.
Strictly say, it is firmware issue - it should issue "disconnect"
event but it does not. Compensate in the driver.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Other parts of Rx path (BACK logic) will need to access associated data
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to multi-tx-queue design, wil_start_xmit() used to be executed
concurrently for different queues. Then, these transmits delivered
to the same queue, creating race.
As result, Tx descriptor may be skipped, causing stall in hardware.
Convert to single Tx queue fixes it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows to account for Tx errors
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move WMI related operations to wmi.c as helper functions
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce debug category "MISC", convert all raw wil_dbg() to this category.
This improves dynamic debug manageability
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make printings from IRQ appears in dmesg in chronological order
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the firmware, added is ability to report internal errors using IRQ.
Catch this IRQ and notify user space via netlink
User space get notified like (udevadm monitor --kernel --property):
KERNEL[12660.320520] change /devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12 (net)
ACTION=change
DEVPATH=/devices/pci0000:00/0000:00:1c.1/0000:02:00.0/0000:03:01.0/0000:05:00.0/net/wlan12
DEVTYPE=wlan
EVENT=FW_ERROR
IFINDEX=6
INTERFACE=wlan12
SEQNUM=2489
SOURCE=wil6210
SUBSYSTEM=net
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check that the array indexes are in-bounds before accessing the rate2 and tmp
arrays.
Found with the following semantic patch:
<smpl>
@@
identifier t;
identifier idx;
expression E;
statement S;
@@
* for (... ; <+... t[idx] ...+> && idx < E ; ...)
S
</smpl>
Signed-off-by: Cyril Roelandt <tipecaml@gmail.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix:
drivers/net/wireless/iwlegacy/4965.c: In function ‘il4965_post_associate’:
drivers/net/wireless/iwlegacy/4965.c:1751:25: warning: variable ‘conf’ set but
not used [-Wunused-but-set-variable]
seen when building allmodconfig on x86_64 with W=1 by removing the unused
variable.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is based on "iwlwifi: fix antenna bitmask".
(362b0563b2)
Like the new iwlagn devices, the old 4965N device only
supports a maximum of three antennas. Hence only three
bits are used, the fourth bit is likely the A-MPDU
indicator.
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of converting it to a bogus error code -1, we should
return the original error code from lower layer driver. This
error code will be printed so it may give user some clues on
what has happened.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If pci_iomap() fails in mwifiex_pcie_init(), it breaks off initialization,
deallocates all resources, but returns zero.
The patch adds -EIO as return value in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While using STA mode in the AP firmware, avoid
calling some firmware commands which are not
supported by the AP firmware.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Choose interface specific function calls
based on interface type instead of
firmware types.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add and delete self entry in the firmware sta database
for AP interface only. We do not need such an entry for
STA interface.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware supports hardware encryption feature
for the station interface running on AP
firmware.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set mac type for station interface on AP firmware
as secondary. This allows the firmware to set specific
characteristics for the STA interface.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When user wants to add a station interface when
AP firmware is loaded & in-use, allow creating
it and also notify user about the same.
Allow adding max one STA interface for AP fw.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Specify the STA support in iface_limit and
in wihpy->interface_modes
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This avoids calling mwl8k_cmd_rf_antenna functions every
time mwl8k_config function is called.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the commands, that might change the hw characteristics
of the PHY device, stop the running bsses and resume them
once command is complete.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow AP and Mesh mode to operate concurrently using
single radio. Verify this using fonera 2.0n featuring
RT3052 chipset and also TP-LINK TL-WN727N featuring
RT5370 chipset.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemal.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use this macro only on 3 places - remove it and replace by other
appropriate macros for printing messages.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Those messages can flood in dmesg, so do not print them by default.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some messages provide useful information, but are disabled without
CONFIG_RT2X00_DEBUG=y, so enable them by default
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sample data received through the spectral scan can be either in big or
little endian byteorder. This information isn't stored in the output file.
Therefore it is not possible for the analyzer software to find the correct byte
order.
It is relative common to get the data from a low end AP in big endian mode and
transfer it to another computer in little endian mode to analyze it. Therefore,
it would be better to store it in network (big endian) byte order.
The extension of the 8 bit bins for each bin to 16 bit is not necessary. This
operation can be done in userspace or on a different machine. Instead the
max_exp defining the amount of shifting required for each bin is exported to
userspace.
The change of the output format requires a change of the type in the sample
tlv to allow the userspace program to correctly detect the bin format.
Reported-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Sven Eckelmann <sven@open-mesh.com>
[siwu@hrz.tu-chemnitz.de: squashed patches, update commit message, rebase, fix endianess bug]
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using the spectral scan feature, frames with phy errors are
returned for further processing to the driver. However, if the frames
also have an invalid CRC (which seems to happen quite often), the frame
is marked with bad CRC and not with the PHY error bit. The FFT
processing function will thus miss the frames.
Fix this by changing the precedence in error marking.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spectral packets are "bogus" packets and should not be further evaluated
by the RX path.
Statistics are added to keep track of these packets.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export the various parameters to userspace.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes invalid access of RxBD ring buffer descriptor's
length and flag inside PCIe send_data_complete() routine. We are
supposed to modify TxBD buffer descriptor's length and flag here.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Delete successive tests to the same location. This looks like simple code
duplication.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A scan request is split into multiple scan commands queued in
scan_pending_q. Each scan command will be sent to firmware and
its response is handlded one after another.
If any error is detected while parsing IE in command response
buffer the remaining data will be ignored and error is returned.
We should check if there is any more scan commands pending in
the queue before returning error. This ensures that we will call
cfg80211_scan_done if this is the last scan command, or send
next scan command in scan_pending_q to firmware.
Cc: "3.6+" <stable@vger.kernel.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In routine _rtl_rx_pre_process(), skb_dequeue() is called to get an skb;
however, the wrong variable name is used in subsequent calls.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This issue was reported on the wireless list (see [1]) in which
brcmsmac ran into a fatal error:
[ 588.284074] brcmsmac bcma0:0: frameid != txh->TxFrameID
[ 588.284098] brcmsmac bcma0:0: MI_TFS: fatal
[ 588.284103] brcmsmac bcma0:0: wl0: fatal error, reinitializing
[ 588.286208] ieee80211 phy0: Hardware restart was requested
The tx status feedback is processed in a loop limiting the number of
frames processed in one run. The code terminate processing when the
limit is reached regardless the txstatus value read from the device
register. When that status is is flagged as being valid it must be
processed as the hardware will clear it after is has been read.
Bisecting was done by Seth Forshee and showed following commit as the
culprit:
commit 57fe504817
Author: Piotr Haber <phaber@broadcom.com>
Date: Wed Nov 28 21:44:07 2012 +0100
brcmsmac: fix bounds checking in tx/rx
[1] http://www.spinics.net/lists/linux-wireless/msg101293.html
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The iwl-op-mode.h file uses a struct dentry for debugfs
so should include debugfs.h.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since drivers can support several BSS / P2P Client
interfaces, the rssi callback needs to inform the driver
about the interface teh rssi event relates to.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the pages are to be used by front-end, it may need
to know the page order, provide it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit f590dcec94
which has been reported to cause issues.
See https://lkml.org/lkml/2013/1/20/4 for further details.
Cc: stable@vger.kernel.org [3.7]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It is kept per-channel, so removing unnecessary (or constant) fields from
it can save quite a bit of memory.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They are no longer needed for ANI functionality
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dropping packets from aggregation sessions is usually not a good idea, as
it might upset the synchronization of the BlockAck receive window of the
remote node. The use of the retry_tx parameter to reset/tx-drain functions
also seemed a bit arbitrary.
This patch removes this parameter altogether and ensures that pending tx
frames are not dropped for no good reason.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Completing frame transmission can fail if the rx engine is stopped
prematurely, as the hw might be waiting for an ACK from the other side.
Shutting down tx before rx might make the DMA shutdown more reliable.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of variable packet_beacon might be uninitialized in the three files.
Signed-off-by: Cong Ding <dinggnu@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If hardware is not ready, il4965_pci_probe() breaks off initialization,
deallocates all resources, but returns zero.
The patch adds -EIO as return value in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If pci_iomap() fails in mwl8k_probe(), it breaks off initialization,
deallocates all resources, but returns zero.
There is a similar issue when priv->rxd_ops is NULL in mwl8k_probe_hw().
The patch adds proper error code return values.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When AP responds with appropriate status code, we forward that
code correctly to cfg80211. But sometimes when there is no
response from AP, our firmware uses proprietary status codes.
We will map authentication timeout to WLAN_STATUS_AUTH_TIMEOUT
and other proprietary codes to WLAN_STATUS_UNSPECIFIED_FAILURE.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since rt2800 hardware isn't capable of reporting the TX status of
BlockAckReq frames implement the TX status handling of BARs in
rt2x00lib. We keep track of all BARs that are send out and try to
match incoming BAs to the appropriate BARs. This allows us to report a
more or less accurate TX status for BAR frames which in turn improves
BA session stability.
This is loosley based on Christian Lamparter's patch for carl9170
"carl9170: fix HT peer BA session corruption".
We have to walk the list of pending BARs for every rx'red BA even
though most BAs don't belong to any of these BARs as they are just
acknowledging an AMPDU. To keep that overhead low use RCU which allows
us to walk the list of pending BARs without the need to acquire a lock.
This however requires us to _copy_ relevant information from the BAR
(RA, TA, control field, start sequence number) into our BAR list entry.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Tested-by: Andreas Hartmann <andihartmann@01019freenet.de>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is a missing break statement so SHARED_KEY authentication doesn't
work.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There were no break statements in this switch statement so everything
used the default settings. Per Walter Harms's suggestion, I've replaced
the switch statement and done a little cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
in ray_cs.c:
the a_current_ess_id is "Null terminated unless ESSID_SIZE long"
so we need buffer it with '\0' firstly, before using strlen or %s.
additional information:
in drivers/net/wireless/rayctl.h:
"NULL terminated unless 32 long" is a comment at line 616, 664
ESSID_SIZE is 32, at line 190
in include/uapi/linux/wireless.h:
IW_ESSID_MAX_SIZE is also 32
in drivers/net/wireless/ray_cs.c:
use strncpy for it, without '\0' terminated, at line 639
use memcpy for it, assume not '\0' terminated in line 1092..1097
buffer it with '\0' firstly, before using %s, in line 2576, 2598..2600
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ar900*_init_mode_regs needs to be called before RF banks are allocated,
otherwise the storage size of RF banks isn't known. This patch fixes
a memory overrun that can show up as a crash on unloading the module.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing "!" as we are supposed to check "!card->adapter"
in PCIe suspend handler.
Cc: "3.2+" <stable@vger.kernel.org>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Reviewed-by: Sergey V. <sftp.mtuci@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Chain swapping should only be enabled when the EEPROM chainmask is set to 5,
regardless of what the runtime chainmask is.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kbuild test robot reports the following warning with x86_64-randconfig-x955:
warning: (RTL8192CE && RTL8192SE && RTL8192DE && RTL8723AE && RTL8192CU) selects
RTLWIFI which has unmet direct dependencies (NETDEVICES && WLAN &&
(RTL8192CE || RTL8192CU || RTL8192SE || RTL8192DE))
This warning was introduced in commit a290593, "rtlwifi: Modify files for addition
of rtl8723ae", and is d ue to a missing dependence of RTLWIFI on RTL8723AE.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: kbuild test robot <fengguang.wu@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not correctly change interface type when switching from
IBSS mode to STA mode, that results in microcode errors.
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=886946
Reported-by: Jaroslav Skarvada <jskarvad@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Also when things go wrong (queues don't get emtpy), try to
get some data from the HW.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The rate scaling won't treat the information in a frame
with IEEE80211_TX_CTL_AMPDU set if IEEE80211_TX_STAT_AMPDU
is cleared. But all the frames coming from an AGG tx queue
have IEEE80211_TX_CTL_AMPDU set, and IEEE80211_TX_STAT_AMPDU
is set only if the frame was sent in an AMPDU.
This means that all the data in frames in AGG tx queues that
aren't sent as an AMPDU is thrown away.
This is even more harmful when in bad link conditions, the
frames are sent in an AMPDU and then finally sent as single
frame. So a lot of failures weren't reported and the rate
scaling got stuck in high rates leading to very poor
connectivity.
Fix that by clearing IEEE80211_TX_CTL_AMPDU when the frame
isn't part of an AMPDU.
This bug was introduced by
2eb81a40aa
iwlwifi: don't clear CTL_AMPDU on frame status
This fix basically reverts the aforementioned commit.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On resuming, the opmode may have to be able to talk
to the WoWLAN/D3 firmware in order to query it about
its status and wakeup reasons. To do that, the opmode
has to call the new d3_resume() transport API which
will set up the device for command communcation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Writing 130 dwords into the device one by one is
rather inefficient, every one needs to lock, grab
NIC access (a few register reads/writes) and then
write the address and data registers.
Use the new memory clearing function to make this
easier and faster.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sending a NULL pointer to iwl_trans_write_mem allows now
to zero SRAM.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enabling the RF-kill interrupt is sufficient for getting
RF-kill notifications, and no other interrupt is needed
as the device isn't functional when suspended and will be
restarted/reconfigured when mac80211 resumes it later.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The dma_addr_t type is a scalar value, so it should
just be assigned, not memset.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes a reported CPU soft lockup where the tasklet tries to acquire the
lock and blocks while ath_prepare_reset (holding the lock) waits for it
to complete.
Cc: stable@vger.kernel.org
Reported-by: Robert Shade <robert.shade@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: fix rx flush handling" added a deadlock that happens
because ath_rx_tasklet is called in a section that has already taken the
rx buffer lock.
It seems that the only purpose of the rxbuflock was a band-aid fix to the
reset vs rx tasklet race, which has been properly fixed in the commit
"ath9k: add a better fix for the rx tasklet vs rx flush race".
Now that the fix is in, we can safely remove the lock to avoid such issues.
Cc: stable@vger.kernel.org
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The reg_notifier()'s return value need not be checked
as it is only supposed to do post regulatory work and
that should never fail. Any behaviour to regulatory
that needs to be considered before cfg80211 does work
to a driver should be specified by using the already
existing flags, the reg_notifier() just does post
processing should it find it needs to.
Also make lbs_reg_notifier static.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[move lbs_reg_notifier to not break compile]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Improves stability on affected devices and also fixes the Tx IQ calibration
related regression on some AR9340 devices such as the TP-Link TL-WDR4300.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There was a copy+paste error in ar9002 for the endless spectral mode,
fix that.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set the beacon timestamp once during "transmission" so the
monitor interface also gets a timestamped beacon.
Also use a common base between TX timestamp and RX
mactime. This eliminates "TX" path delay, which shows up
as a constant error in Toffset.
Get the global TSF once before iterating over all RX HWs,
so they all set a mactime with the same time base.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On hardware reintialization reference count of
already existing timers would be increased again.
This leads to problems on module unloading.
Cc: stable@vger.kernel.org
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now the rx flush is not doing anything useful on AR9003+, as it only
works if the buffers in the rx FIFO have not been purged yet, as is done
by ath_stoprecv.
To fix this, always call ath_flushrecv from within ath_stoprecv before
the FIFO is emptied, but still after the hw receive path has been stopped.
This ensures that frames received (and ACKed by the hardware) shortly before
a reset will be seen by the software, which should improve A-MPDU session
stability.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure that the rx tasklet is no longer running when entering the reset path.
Also remove the distinction between flush and no-flush frame processing.
If a frame has been received and ACKed by the hardware, the stack needs to see
it, so that the BA receive window does not go out of sync.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During teardown, mac80211 will not return a new beacon. This is normal and
handled properly in the driver, so there's no need to spam the user with a kernel
warning here.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the next beacon is sent, the ath_buf from the previous run is reused.
If getting a new beacon from mac80211 fails, bf->bf_mpdu is not reset, yet
the skb is freed, leading to a double-free on the next beacon tx attempt,
resulting in a system crash.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR9300 the rx FIFO needs to be empty during reset to ensure that no
further DMA activity is generated, otherwise it might lead to memory
corruption issues.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SKBs that are allocated in the HTC layer do not have callbacks
registered and hence ended up not being freed, Fix this by freeing
them properly in the TX completion routine.
Cc: <stable@vger.kernel.org>
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BAND_G is implicit when BAND_GN is present.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently "adapter->config_bands" is updated during infra
association only if channel is provided by user in "iw connect"
command. config_bands is used while preparing association
request to calculate supported rates by intersecting our rates
with the rates advertised by AP.
There is corner case in which we include zero rates in
supported rates TLV based on previous IBSS network history,
which leads to association failure.
This patch fixes the problem by correctly updating config_bands.
Cc: "3.7.y" <stable@vger.kernel.org>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds the spectral scan feature for ath9k. AR92xx and AR93xx chips
are supported for now. The spectral scan is triggered by configuring
a mode through a debugfs control file. Samples can be gathered via
another relay debugfs file.
Essentially, to try it out:
echo chanscan > /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan_ctl
iw dev wlan0 scan
cat /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan0 > samples
echo disable > /sys/kernel/debug/ieee80211/phy0/ath9k/spectral_scan_ctl
This feature is still experimental.
The special "chanscan" mode is used to perform spectral scan while
mac80211 is scanning for channels. To allow this,
sw_scan_start/complete() ops have been added.
The patch contains code snippets and information from Zefir Kurtisi and
information provided by Adrian Chadd and Felix Fietkau.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For AR9550, program the synth value based on the ref. clock.
The logic for AR9550 is similar to AR9330, but keep the code
separate since changes for AR9330 are required - which would be
done later.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If queues are stopped in mwl8k_stop,
these should be started in mwl8k_start
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station deauths, we do not delete the streams with state
AMPDU_STREAM_NEW and these remain created forever. Fix this issue by
removing such streams in the driver
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever TX ring is drained, priv->tx_wait still points
to a valid completion. Making sure that it points to
NULL before returning from the mwl8k_tx_wait_empty
check.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When AGC calibration is to be done, a GPM message with the
payload, MCI_GPM_WLAN_CAL_REQ has to be sent. Currently this falls
within the IQ-CAL code block which is incorrect. Fix this by using
a separate variable to decide when IQ-CAL is to be done separately
and call ar9003_mci_init_cal_req correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IQ calibration doesn't complete and times out for half/quarter
rates, so skip it correctly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch is an enhacement to mwifiex_pcie driver to use
map/unmap PCI memory APIs. This reduces one memcpy each in TX
path and RX path, and enhances throughput.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds handler to clean PCIe TX rings after disconnect
or bss stop is called for PCIe based mwifiex driver.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses pci_alloc_consistent and pci_free_consistent
APIs for mwifiex_pcie driver. Consistent DMA memory is allocated
for TX, RX and event rings. Command buffer and command response
buffer also uses map/unmap memory APIs to download commands and
get command responses.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for init_fw_port handler for PCIe
interface, which resets RXBD read pointer for PCIe.
This fixes issue where RX doesn't work until some TX from
driver happens.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a bug for few instances where PCIe interrupt
status variable is accessed without holding spin lock.
This can result into missing interrupts.
Fix this by copying interrupt status to a local variable and
then using it for calling specific routine.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TX_IQ_ON_AGC_CAL should not be enabled for AR9340. TX-IQ calibration
is run as part of AGC calibration only for AR9485, AR9462 and AR9565.
For the others (AR9300, AR9330, AR9340), TX-IQ cal is done independent
of AGC-cal.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New firmware is required to support
a) Add support for additional ampdu streams
b) Handle corresponding watchdog events to destroy ampdu streams
Bumping firmware API version by one.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, command path waits till all the tx host queues
are empty. Whenever watchdog event is raised, firmware
expects driver to destroy ampdu queues immediately.
This requires corresponding commands i.e.
mwl8k_cmd_get_watchdog_bitmap and mwl8k_destroy_ba to be
sent without waiting for the tx queues to be completely
empty.
Use "watchdog_event_pending" to ensure the above mentioned
two commands are sent down immediately.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With more ampdu streams, we need to handle watchdog
events for the new ampdu streams. Handle these
events appropriately.
Earlier mwl8k_cmd_get_watchdog_bitmap used to return
only one stream index and hence bitwise operations
on the return value were not required. Now the function
returns a bitmap with different bits are mapped with
different stream indices.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, mwl8k_ampdu_stream is passed as one of the
argument to the function mwl8k_destroy_ba. Instead of
this pass only the stream index. This will be helpful
during watchdog event handling when bitmap of stream
indices are received.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, we have 2 ampdu streams that can be created
simultaneously. Firmware is capable of supporting
additional streams. Add support to use these streams.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set ACK policy to NORMAL when its not going to
be an AMPDU packet.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ampdu stream index can be derived from stream->idx.
So we no longer need stream->txq_idx, hence removing it.
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is not enabled for any chip and is unused.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Doing this in ath9k_hw_fill_cap_info() is odd and it's
cleaner to do this in the init function for calibration.
Also, setup the supported calibration type in init_cal_settings.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for parsing WMM IEs from hostapd
and setting them to FW via sys configure command.
Patch also sets wiphy flag to advertise AP uAPSD support.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is observed that same htcapinfo ie is included in beacon for
HT20, HT40+ and HT40- ibss networks. This patch makes sure that
we will not advertise 40Mhz flags while creating/joining ibss
network in HT20 mode.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We know 'firmware' is non-NULL from the beginning of mwifiex_prog_fw_w_helper,
remove all !firmware paths from the rest of the function.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If pci_set_dma_mask() or pci_set_consistent_dma_mask() fails in p54p_probe(),
it breaks off initialization, deallocates all resources, but returns zero.
Similar issue is if check for returned value of pci_resource_len() fails.
The patch implements proper error code propagation.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On interface up dongle gets inialized. Move UP command to common
routine and update these common init routines using ifp.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Netdev xmit routine brcfm_netdev_start_xmit was defined
incorrectly and used wrong return codes. Always eat the
packet and return ok. Remove drvr_up check since it is not
relevant.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CDC errors are retained. However, it is never used so it can
be removed.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stumbled into a curly braces used for if statement with only
one conditional statement. Removing them.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The header of the ethernet packet is processed conditionally, but
the check is wrong as it checks skb length is at least ETH_ALEN. It
should check it is at least sizeof struct ethhdr instead.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver had some global definitions in dhd.h to map event
identifiers to event names. With redesign of firmware event
processing this has all moved to fweh module so these definitions
can be removed.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CDC debug is partly done with TRACE and partly with CTL, however
CDC hardly ever needs debugging. Use dedicated level CDC and
replace TRACE and CTL in dhd_cdc with that.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The use of the function brcmf_proto_hdrpull() is moved to the
common part of the driver and consequently it can be removed
from the bus interface.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bus interface provided a wrapper function to pass a single
packet to the common driver part filling a skb queue with one
packet. For clarity the caller now sets up the skb queue and
call the rx bus interface function.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Several source files (but not all) define the pr_fmt() macro in exactly
the same way. Instead this commit defines it in a header file so driver
logging is consistent.
Cc: Joe Perches <joe@perches.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upon unloading the brcmfmac module the USB firmware should be reset
as the device remains powered. The reset assures a known device
state when a new brcmfmac driver load is being done.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set bitrate_mask is not desired anymore. The firmware will
determine the correct rates to be used.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When USB device gets removed rx complete comes with 0-length
packets. Do not refill those packets. In some rare cases it can
cause infinite loop.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dead code after AMPDU restructure.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The interface address of the wireless device is determined by
the permanent address stored in the device. This patch allows
it to be overridden from user-space.
Reported-by: Maximilian Engelhardt <maxi@daemonizer.de>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All callbacks that access driver functions should do that under
perimeter lock protection. The add_interface() callback was lacking
this lock.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On hardware reintialization reference count of
already existing timers would be increased again.
This leads to problems on module unloading.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both the rtt2x00usb_eeprom_read and the ioremap
functions are allowed to fail, however their
return values are not checked in the read_eeprom
functions in the rt2800{pci,usb} drivers.
The patch adds the missing checks, and converts
all read_eeprom functions to return an int value,
so the error values can be propagated up to the
'rt2800_validate_eeprom' function.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/brcm80211/brcmsmac/main.c: In function ‘brcms_b_recv’:
drivers/net/wireless/brcm80211/brcmsmac/main.c:7636: warning: ‘morepending’ may be used uninitialized in this function
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Power save support was removed from iwlegacy due to possible firmware
crashes problems it cause. I use to plan first inspect code to find
reason of problems, fix them and then allow to enable PS. But
realistically - code inspection will not happen, so let's do it, and
wait for eventual bug reports.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dump implementation of flush, which just wait until all TX queues
become empty.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some 3-column initval arrays have wrong comments. The
column of these arrays is indexed by the 'freqIndex'
variable in 'ar5008_hw_process_ini' which only depends
on the actual band.
The 'initvals' tool from 'qca-swiss-army-knife' prints
the correct comment lines for these arrays, since commit
'atheros-initvals: fix comments for non-fastclock 3-column tables'
however the comments were not refreshed in ath9k.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves parts of carl9170_update_beacon
into separate subroutines, so the parts become
more manageable.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit: "mac80211: introduce IEEE80211_NUM_TIDS and use it"
introduced a generic NUM_TID definitions for all everyone.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While the driver supports HW offload in a single
P2P client configuration, it doesn't support HW
offload in the concurrent P2P GO+CLIENT
configuration.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously, op_start would set disable_offload always
to false, even if it was set to true by the fw parser.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise carl9170 triggers a warning in cfg80211, from net/wireless/core.c
/* Combinations with just one interface aren't real */
if (WARN_ON(c->max_interfaces < 2))
Note: The number of supported interfaces is set by
the carl9170 firmware. The default number of
supported interfaces for all current firmwares is 2.
Therefore this warning can only be observed with
custom firmwares.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Janusz Dziedzic reported that after a change in wpa_supplicant
["nl80211: Automatically use concurrent P2P if possible"],
carl9170 was no longer able to host a P2P network.
This patch tackles the problem by allowing GO interfaces to be
registered, long after the P2P_CLIENT interface is brought up.
Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on a quick test [ath9k and carl9170],
TDLS seemed to be working fine. And while
we are at it, let's move the wiphy feature
flag set from carl9170_alloc into a single
place in carl9170_fw.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800_init_rfcsr() is too big, split RF initialization into per chip
functions. Code will change, but we should setup the same values onto
RF registers and in the same order as before.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent versions of udev cause synchronous firmware loading from the
probe routine to fail because the request to user space would time
out. The original fix for b43 (commit 6b6fa58) moved the firmware
load from the probe routine to a work queue, but it still used synchronous
firmware loading. This method is OK when b43 is built as a module;
however, it fails when the driver is compiled into the kernel.
This version changes the code to load the initial firmware file
using request_firmware_nowait(). A completion event is used to
hold the work queue until that file is available. This driver
reads several firmware files - the remainder can be read synchronously.
On some test systems, the async read fails; however, a following synch
read works, thus the async failure falls through to the sync try.
Reported-and-Tested by: Felix Janda <felix.janda@posteo.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> (V3.4+)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fields must be null-terminated, or simple_strtoul will cause issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not dereference p->station_id after kfree(cmd) because p
points into the cmd data structure.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Julian Wollrath <jwollrath@web.de>
Acked-by: Larry Finger <Larry.finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds support for the 60 GHz 802.11ad Wilocity card
through a new driver, wil6210. Wilocity implemented the
firmware, QCA maintains the device driver.
Currently supported:
- STA: with security
- AP: limited to 1 connected STA, security disabled
- Monitor: due to a hardware/firmware limitation
either control or non-control frames are monitored
Using a STA and AP with this drive, one can assemble
a fully functional BSS. Throughput of 1.2Gbps is achieved
with iperf.
The wil6210 cards have on-board flash memory for the
firmware, the cards comes pre-flashed and no firmware
download is required.
For more details see:
http://wireless.kernel.org/en/users/Drivers/wil6210
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wait_event_interruptible function returns -ERESTARTSYS if it's
interrupted by a signal. Driver should check the return value
and handle this case properly.
In mwifiex_wait_queue_complete() routine, as we are now checking
wait_event_interruptible return value, the condition check is not
required. Also, we have removed mwifiex_cancel_pending_ioctl()
call to avoid a chance of sending second command to FW by other path
as soon as we clear current command node. FW can not handle two
commands simultaneously.
Cc: "3.6+" <stable@vger.kernel.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ath9k consists of 2 different sub-modules: ATH9K and ATH9K_HTC.
Both uses common Atheros code from ath.ko and need ATH_COMMON.
However, while ATH9K selects ATH_COMMON, ATH9K_HTC does not.
As result, if ATH9K_HTC is the only Atheros card selected, compilation fails with
unresolved symbols.
This patch moves ATH_COMMON selection to the common part for both
ATH9K and ATH9K_HTC
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A beacon period starts at TSF time 0. Spoof this by
rounding the starting beacon time to a multiple of the
beacon interval, and keep TBTT aligned on TSF adjustment.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For testing various timing-sensitive protocols (power
save, MBCA, etc.), a beacon accuracy of jiffies is not
sufficient. A tasklet_hrtimer is used for the beacon since
it runs the callback in soft-IRQ context with hrtimer
resolution.
Also handle BSS_CHANGED_BEACON_ENABLED for hwsim.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[simplify timer container_of]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make hwsim TSF offset adjustments cumulative and relative
to the fake PHY TSF. Now adding 1000us, then adding -1000us
doesn't result in a tsf_offset of -1000. Also the beacon
timestamp can now correctly be expressed as (tsf +
data->tsf_offset), which will be done in a later patch.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows to let sparse check that the NIC access is
always released.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix typo in the macro name and the wrong value.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Synchronizing the IRQ is pointless when we will
then enable the RF-Kill interrupt again, but is
needed before we free it and the data needed to
handle IRQs; move it to the free function.
Simiarly, cancelling the replenish work struct
can move to the function that frees the RX data
structures.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's no need to request the IRQ every time the
device is started, we can request it just once.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
iwl_trans_grab_nic_access returns a boolean. So ret should
explicitely set to an error code and not rely on the value
returned by iwl_trans_grab_nic_access.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a bug in the currently released firmware version,
the sequence control in the Tx response isn't updated in
all cases. Take it from the packet as a workaround.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Different transports implement the access to the SRAM in
different ways. Virtualize it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since different transports have different ways to wake the
up the NIC, we need to virtualize it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By accident, commit eb6476441b
("iwlwifi: protect use_ict with irq_lock") changed the return
value of the iwl_pcie_isr() function in case it handles an
interrupt -- it now returns IRQ_NONE instead of IRQ_HANDLED.
Put back the correct return value.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use __packed instead of __attribute__((packed)).
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some cases, the fw should run even if the NIC is in
RFKILL. Make the API more flexible to allow that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
No need to verify that the fw has been written correctly.
In case it hasn't, we won't get ALIVE notification.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we take a pointer to the tid_data, then use it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When TX aggregation is stopped, there are a few
different cases:
- connection with the peer was dropped
- session stop was requested locally
- session stop was requested by the peer
- connection was dropped while a session is stopping
The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.
Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.
In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of returning an error and filling a pointer
return the pointer and an ERR_PTR value in error cases.
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The channel bandwidth handling isn't really quite right,
it assumes that a 40 MHz channel is really two 20 MHz
channels, which isn't strictly true. This is the way the
regulatory database handling is defined right now though
so remove the logic to handle other channel widths.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Paged RX, i.e. SKBs with (some of) the data in pages instead
of the SKB header data (skb->data) can behave differently in
the stack and cause other bugs. To make debugging easier add
an option to hwsim to test with such SKBs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
RSN IEs got incorrectly parsed and therefore ap mode using WPA2
security was not working.
Cc: stable@vger.kernel.org
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Patches from Canonical involved the introduction of new source
files debug.[ch]. That coincided with other patches from Broadcom
introducing the same files.
Cc: Seth Forshee <seth.forshee@canonical.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
