The Olinuxino board uses DDR3L chips which are supposed to be driven
with 1.35V. The reset default of the AXP is properly set to 1.36V.
While technically the chips can also run at 1.5 volts, changing the
voltage on the fly while booting Linux is asking for trouble. Also
running at a lower voltage saves power.
So fix the DCDC5 value to match the actual board design.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Martin Lucina <martin@lucina.net>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win board uses the AXP's ALDO1 power rail to drive the
VCC-CSI line, which, according to the schematic, needs to be set to 2.8V.
Also the ELDO3 power rail is connected to the CSI, with somewhat unclear
voltage requirements. Add this regulator and allow the voltage to be set
between 1.5V and 1.8V, which are the voltages mentioned in the
schematic.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win comes with 2 MB SPI flash, add the node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win features a soldered WiFi chip on the board, connected
via the SDIO interface. Add the required DT nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a green status LED, add the DT node for it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win exposes several UARTs on header pins, and connects one
to the on-board WiFi/Bluetooth chip.
Add the pinmux definitions to the UART nodes, but keep them disabled.
Enable the UART1, which is wired to the Bluetooth chip, and add a serdev
node. There is no binding for the BT8723 yet, so leave this mostly empty
for now.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has the usual Gigabit PHY connected to the EMAC.
Its power is controlled by GPIO PD14.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a micro USB-B socket, connected to the SoC's
USB-OTG port. Its power is supplied by the AXP PMIC, and the ID pin is
connected to GPIO PH9. It can serve both as a host or a client port.
Add the respective DT nodes to enable it.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: enable paired EHCI/OHCI device nodes and regulator supply]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has four standard USB-A sockets, connected to an
on-board USB hub. The hub's and socket's power regulators are enabled by
GPIO PD7.
Add the regulator to the DT to enable the power supply.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Orange Pi Win has a microSD card slot which is connected via all
four SD data lines. As the DT was not mentioning this fact, we got the
default single bit transfers, losing out on performance.
Also, as microSD does not have a write protect switch, we disable this
feature in the DT node.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The Pine64-LTS is a variant of the Pine64 board, from the software
visible side resembling a SoPine module on a baseboard, though the
board has the SoC and DRAM integrated on one PCB.
Due to this it basically shares the DT with the SoPine baseboard, which
we mimic in our DT by inclucing the boardboard .dts into the new file,
just overwriting the model name.
Having a separate .dts for this seems useful, since we don't know yet if
there are subtle differences between the two. Also the SoC on the LTS
board is technically an "R18" instead of the original "A64", although as
far as we know this is just a relabelled version of the original SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Current kernels complain when booting on an A64 Soc:
....
[ 1.904297] cacheinfo: Unable to detect cache hierarchy for CPU 0
....
Not a real biggie on this flat topology, but also easy enough to fix.
Add the L2 cache node and let each CPU point to it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Another user of cd-inverted seems to have crept in. Switch it away from
cd-inverted to be consistent with other sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A64 have a SID controller which consist of EFUSE (starting at 0x200)
and three registers to read/write some of the protected efuses.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A couple of late-merged changes that would be useful to get in this
merge window:
- Driver support for reset of audio complex on Meson platforms. The
audio driver went in this merge window, and these changes have been
in -next for a while (just not in our tree).
- Power management fixes for IOMMU on Rockchip platforms, getting
closer to kexec working on them, including Chromebooks.
- Another pass updating "arm,psci" -> "psci" for some properties that
have snuck in since last time it was done.
-----BEGIN PGP SIGNATURE-----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=dQaG
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late updates from Olof Johansson:
"A couple of late-merged changes that would be useful to get in this
merge window:
- Driver support for reset of audio complex on Meson platforms. The
audio driver went in this merge window, and these changes have been
in -next for a while (just not in our tree).
- Power management fixes for IOMMU on Rockchip platforms, getting
closer to kexec working on them, including Chromebooks.
- Another pass updating "arm,psci" -> "psci" for some properties that
have snuck in since last time it was done"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
iommu/rockchip: Move irq request past pm_runtime_enable
iommu/rockchip: Handle errors returned from PM framework
arm64: rockchip: Force CONFIG_PM on Rockchip systems
ARM: rockchip: Force CONFIG_PM on Rockchip systems
arm64: dts: Fix various entry-method properties to reflect documentation
reset: imx7: Fix always writing bits as 0
reset: meson: add meson audio arb driver
reset: meson: add dt-bindings for meson-axg audio arb
The idle-states binding documentation[1] mentions that the
'entry-method' property is required on 64-bit platforms and must be
set to "psci".
commit a13f18f59d ("Documentation: arm: Fix typo in the idle-states
bindings examples") attempted to fix this earlier but clearly more is
needed.
Fix the cpu-capacity.txt documentation that uses the incorrect value so
we don't get copy-paste errors like these. Clarify the language in
idle-states.txt by removing the reference to the psci bindings that
might be causing this confusion.
Finally, fix devicetrees of various boards to reflect current
documentation.
[1] Documentation/devicetree/bindings/arm/idle-states.txt (see
idle-states node)
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN and
PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor variants
of boards/platforms.
-----BEGIN PGP SIGNATURE-----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=J0qC
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Olof Johansson:
"Business as usual -- the bulk of our changes are to devicetree files
with new hardware support, new SoCs and platforms, and new board
types.
New SoCs/platforms:
- Raspberry Pi Compute Module (CM1) and IO board
- i.MX6SSL from NXP
- Renesas RZ/N1D SoC (R9A06G032), Dual Cortex-A7 with Ethernet, CAN
and PLC interfaces
- TI AM654 SoC, Quad Cortex-A53, safety subsystem with Cortex-R5
controllers, communication and PRU subsystem and lots of other
interfaces (PCIe, USB3, etc).
New boards and systems:
- Several Atmel at91-based boards from Laird
- Marvell Armada388-based Helios4 board from SolidRun
- Samsung Aires-based phones (s5pv210)
- Allwinner A64-based Pinebook laptop
In addition to the above, there's the usual amount of new devices
described on existing platforms, fixes and tweaks and new minor
variants of boards/platforms"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (478 commits)
arm64: dts: sdm845: Add tsens nodes
arm64: dts: msm8996: thermal: Initialise via DT and add second controller
arm64: dts: sprd: Add one suspend timer
arm64: dts: sprd: Add SC27XX ADC device
arm64: dts: sprd: Add SC27XX eFuse device
arm64: dts: sprd: Add SC27XX vibrator device
arm64: dts: sprd: Add SC27XX breathing light controller device
arm64: dts: meson-axg: add spdif-dit codec
arm64: dts: meson-axg: add lineout codec
arm64: dts: meson-axg: add linein codec
arm64: dts: meson-axg: add tdm interfaces
arm64: dts: meson-axg: add tdmout formatters
arm64: dts: meson-axg: add tdmin formatters
arm64: dts: meson-axg: add spdifout
arm64: dts: rockchip: add led support for Firefly-RK3399
arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399
arm64: dts: rockchip: add power button support for Firefly-RK3399
ARM: dts: aspeed: Add coprocessor interrupt controller
arm64: dts: meson-axg: add audio arb reset controller
arm64: dts: meson-axg: add usb power regulator
...
This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr. In addition, with the
continuing absence of Nic we have target updates for tcmu and target
core (all with reviews and acks). The biggest observable change is
going to be that we're (again) trying to switch to mulitqueue as the
default (a user can still override the setting on the kernel command
line). Other major core stuff is the removal of the remaining
Microchannel drivers, an update of the internal timers and some
reworks of completion and result handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCW3R3niYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishauRAP4yfBKK
dbxF81c/Bxi/Stk16FWkOOrjs4CizwmnMcpM5wD/UmM9o6ebDzaYpZgA8wIl7X/N
o/JckEZZpIp+5NySZNc=
=ggLB
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: mpt3sas, lpfc, qla2xxx,
hisi_sas, smartpqi, megaraid_sas, arcmsr.
In addition, with the continuing absence of Nic we have target updates
for tcmu and target core (all with reviews and acks).
The biggest observable change is going to be that we're (again) trying
to switch to mulitqueue as the default (a user can still override the
setting on the kernel command line).
Other major core stuff is the removal of the remaining Microchannel
drivers, an update of the internal timers and some reworks of
completion and result handling"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (203 commits)
scsi: core: use blk_mq_run_hw_queues in scsi_kick_queue
scsi: ufs: remove unnecessary query(DM) UPIU trace
scsi: qla2xxx: Fix issue reported by static checker for qla2x00_els_dcmd2_sp_done()
scsi: aacraid: Spelling fix in comment
scsi: mpt3sas: Fix calltrace observed while running IO & reset
scsi: aic94xx: fix an error code in aic94xx_init()
scsi: st: remove redundant pointer STbuffer
scsi: qla2xxx: Update driver version to 10.00.00.08-k
scsi: qla2xxx: Migrate NVME N2N handling into state machine
scsi: qla2xxx: Save frame payload size from ICB
scsi: qla2xxx: Fix stalled relogin
scsi: qla2xxx: Fix race between switch cmd completion and timeout
scsi: qla2xxx: Fix Management Server NPort handle reservation logic
scsi: qla2xxx: Flush mailbox commands on chip reset
scsi: qla2xxx: Fix unintended Logout
scsi: qla2xxx: Fix session state stuck in Get Port DB
scsi: qla2xxx: Fix redundant fc_rport registration
scsi: qla2xxx: Silent erroneous message
scsi: qla2xxx: Prevent sysfs access when chip is down
scsi: qla2xxx: Add longer window for chip reset
...
This patch is to add clocks property for fman ptp timer node.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable all 4 SEC units available on d05 boards.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Modify the base address of the mdio mux driver to point to the
start of the mdio mux block's register address space.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SDM845 has two tsens blocks, one with 13 sensors and the other with 8
sensors. It uses version 2 of the TSENS IP, so use the fallback property to
allow more common code.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
We also split up the regmap address space into two, for the TM and SROT
registers. This was required to deal with different address offsets for the
TM and SROT registers across different SoC families.
8996 has two TSENS IP blocks, initialise the second one too.
Since tsens-common.c/init_common() currently only registers one address
space, the order is important (TM before SROT). This is OK since the code
doesn't really use the SROT functionality yet.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
standard. LEDs and power button for the rk3399 firefly and removal of
some deprecated type-c properties from the rk3399 devicetree.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAltfHXEQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgepyB/9HJZvneyadfomxhywbflJ8wkZj4WWfHDNG
79hwcg33EBcP2+vRkTeYypkurmhZdv+sSF6h1sLUBmtFNuapzd7xlI7FW+NAwwgl
6UFU4DtiC2E0b9ljrCL1WQH34BEVpSyaENO7EF1gR8CvZAnb4BzRgzDxfAczbQlH
6uBRzfuHooW/zHrbLxMxzkMbeHlU7m8i3/F2E3Uftxy5/qHUNmFGNcOl0bCpT/i6
gS1QKIBAMmQ6yaNwrwG6GmPPampv2jXGUCNFAlCNkLPjKY0Ri7XdBq0k91sx78YT
bP7k8Qd+TANMZgHB+mHPhgupMDur8KL+hn5I+MO3DItfn3rUW4EL
=0BU+
-----END PGP SIGNATURE-----
Merge tag 'v4.19-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
A new board, the Vamrs Ficus using the rk3399 and followin the 96boards
standard. LEDs and power button for the rk3399 firefly and removal of
some deprecated type-c properties from the rk3399 devicetree.
* tag 'v4.19-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: add led support for Firefly-RK3399
arm64: dts: rockchip: remove deprecated Type-C PHY properties on rk3399
arm64: dts: rockchip: add power button support for Firefly-RK3399
arm64: dts: rockchip: drop out-of-tree properties from rk3399-ficus regulator
arm64: dts: rockchip: add voltage properties for vcc3v3_pcie on rk3399 ficus
arm64: dts: rockchip: add USB 2.0 and 3.0 support on Ficus board
arm64: dts: rockchip: add 96boards RK3399 Ficus board
dt-bindings: Add vendor prefix for Vamrs Ltd.
Signed-off-by: Olof Johansson <olof@lixom.net>
Use more specific compatible for the Inside Secure SafeXcel on the
Armada 37xx and the Armada 7K/8K SoCs.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCW1GhYAAKCRALBhiOFHI7
1UYeAKCZvsX0evzDYPCmL32CSuArmJ+OKwCdFYn7QoXQIYwGP60bK2UZzhcWROs=
=V7S+
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.19-2' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt64 for 4.19 (part 2)
Use more specific compatible for the Inside Secure SafeXcel on the
Armada 37xx and the Armada 7K/8K SoCs.
* tag 'mvebu-dt64-4.19-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: armada-37xx: update the crypto engine compatible
arm64: dts: marvell: armada-cp110: update the crypto engine compatible
Signed-off-by: Olof Johansson <olof@lixom.net>
- add EINT support
- add gpio-ranges property to pinctrl
- add earlycon to rfb1 to find boot errros more easily
- fix uart clock
- add iommu and smi bindings
- mt6797:
- add support for the 96 board x20 development board
- fix cooling-cells of mt7622 and mt8173
-----BEGIN PGP SIGNATURE-----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=+G4b
-----END PGP SIGNATURE-----
Merge tag 'v4.18-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into next/dt
- mt7622:
- add EINT support
- add gpio-ranges property to pinctrl
- add earlycon to rfb1 to find boot errros more easily
- fix uart clock
- add iommu and smi bindings
- mt6797:
- add support for the 96 board x20 development board
- fix cooling-cells of mt7622 and mt8173
* tag 'v4.18-next-dts64' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: dts: Add Mediatek X20 Development Board support
dt-bindings: arm: mediatek: Document Mediatek X20 Development Board
dt-bindings: mediatek: Add binding for mt2712 IOMMU and SMI
arm64: dts: mt7622: update a clock property for UART0
arm64: dts: mt7622: add earlycon to mt7622-rfb1 board
arm64: dts: mt7622: use gpio-ranges to pinctrl device
arm64: dts: mediatek: Add missing cooling device properties for CPUs
arm64: dts: mt7622: add EINT support to pinctrl
Signed-off-by: Olof Johansson <olof@lixom.net>
Some interesting changes, especially:
- MMC support for the H6
- PMIC support for the PineH64
- HDMI simplefb support for the A64
- PWM support for the A64
- New board: Pinebook, Amarula A64-Relic
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEE0VqZU19dR2zEVaqr0rTAlCFNr3QFAltXJZEACgkQ0rTAlCFN
r3RIsw/8DUoWIlnSocPpRkBSonV55iC0qY4JKjamm/TrhQY5k4MjpX+7/PIyGQAU
uNHn6vOmRILOyQS5Zg+1uWLOPypdxI2aDcQUKYNPdNJ6RytdgH1zghUM0iupOuNb
CnolLpaA5RGjDvH/MarBwBoyxrAvnhLB/d5naUjzO/zoaw5j4K9idJdneJNX/aBi
nezBGxWzjF0Mu1MmFhRUZD9klZcbeUtJK4sJ4yJeKUThoi1kKynpbXvONDB5wL9L
JDVdWeNYrG3ylNHyAezOMM8gezGxSGjfya8zAaOZj/Wo5uvSDG4+oFaoJU2b+uPu
pdHO1pNGgw57HS6ePm/ON8J4U7v8Z99sRK3BZ+3NjxL3nRsvL5jzfZtSnza6v7gb
ONLlk89entDHDmtugpYYRWyw3GECv+1+oqBTngyRK9rctcFxrCsymx9cyHX7OWPC
M521xUHKL84zoFMmvXPKlMHapH+I70k+a6n5kRljQ9/lbKgnjsvenZerEUB41xvV
B2GXdo4MrZS/UYiPpD585InpoXmqC44cp7SOyXtUETAQ/pOQAbqE3cXHpVLnlUX9
yZfjCK6P6tp+lP9B0pFekIlzjhuUnhCqpNsTIp57ionGYRyK7oSVMOr2bf361vXZ
RBLNbQ+43G8IXPKItRLOFuYNHXQlyi7GR5LnLx/UbDcU3IKhj4w=
=MH+c
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner arm64 DT changes for 4.19
Some interesting changes, especially:
- MMC support for the H6
- PMIC support for the PineH64
- HDMI simplefb support for the A64
- PWM support for the A64
- New board: Pinebook, Amarula A64-Relic
* tag 'sunxi-dt64-for-4.19' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (22 commits)
arm64: allwinner: h6: enable MMC0/2 on Pine H64
arm64: allwinner: h6: add device tree nodes for MMC controllers
dt-binding: mmc: sunxi: add H6 compatible (with A64 fallback)
arm64: dts: allwinner: a64: Remove unused address-cells/size-cells of dwmac-sun8i
arm64: dts: allwinner: h6: enable AXP805 PMIC on Pine H64
arm64: dts: allwinner: h6: Use macros for R_CCU clock and reset indices
arm64: dts: allwinner: a64: add HDMI regulator to all DTs' simplefb_hdmi
arm64: dts: allwinner: a64: add device tree node for HDMI simplefb
arm64: dts: allwinner: a64: add necessary device tree nodes for DE2 CCU
arm64: dts: allwinner: h6: Add LED device nodes for Pine H64
arm64: allwinner: a64: allow laptops to wake up from lid
arm64: allwinner: a64: change TERES-I DLDO3's name to start with "vdd"
arm64: allwinner: a64-sopine: Add cd-gpios to mmc0 node
arm64: dts: allwinner: a64: add SRAM controller device tree node
arm64: dts: allwinner: add support for Pinebook
arm64: dts: allwinner: a64: Add PWM controllers
arm64: dts: allwinner: a64: add R_I2C controller
arm64: allwinner: a64-amarula-relic: Enable AP6330 WiFi support
arm64: allwinner: a64: Add RTC clock to phandle 32kHz external oscillator
arm64: allwinner: a64: Add Amarula A64-Relic initial support
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- new SoC: S905W
- new boards: based on S905W: Amlogic P281, Oranth Tanix TX3 Mini
- AXG: add DT for new audio clock controller
-----BEGIN PGP SIGNATURE-----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=bHuf
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64-2-1' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Amlogic 64-bit DT changes for v4.19, round 2
- new SoC: S905W
- new boards: based on S905W: Amlogic P281, Oranth Tanix TX3 Mini
- AXG: add DT for new audio clock controller
* tag 'amlogic-dt64-2-1' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gxl: add support for the Oranth Tanix TX3 Mini
ARM64: dts: meson-gxl: add support for the S905W SoC and the P281 board
dt-bindings: arm: amlogic: Add support for the Oranth Tanix TX3 Mini
dt-bindings: arm: amlogic: Add support for GXL S905W and the P281 board
dt-bindings: add vendor prefix for Shenzhen Oranth Technology Co., Ltd.
ARM64: dts: meson-axg: add the audio clock controller
clk: meson: expose GEN_CLK clkid
clk: meson-axg: add pcie and mipi clock bindings
dt-bindings: clock: add meson axg audio clock controller bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
On Spreadtrum platform, the current clocksource for timekeeping will be
stopped in suspend state, thus add one always-on timer to calculate the
suspend time.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the Spreadtrum SC27XX PMICs ADC device node which contains 32 channels.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the eFuse device node for Spreadtrum SC27XX PMICs.
The SC27XX eFuse contains 32 blocks and each block's data width is
16 bits.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds the vibrator device node for Spreadtrum SC27XX PMICs.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The SC27xx breathing light controller can support 3 outputs:
red LED, green LED and blue LED.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add support for PM8005/PM8998 and related nodes
* Add/fix nodes on SDM845 for I2c, SPI, UART, and RPMH
* Fix BT LED trigger on DB410c
* Drop legacy clock names on MSM8916
* Add gpio line names on DB820c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DQjU
-----END PGP SIGNATURE-----
Merge tag 'qcom-arm64-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/dt
Qualcomm ARM64 Updates for v4.19
* Add support for PM8005/PM8998 and related nodes
* Add/fix nodes on SDM845 for I2c, SPI, UART, and RPMH
* Fix BT LED trigger on DB410c
* Drop legacy clock names on MSM8916
* Add gpio line names on DB820c
* tag 'qcom-arm64-for-4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
arm64: dts: qcom: db410c: Fix Bluetooth LED trigger
arm64: dts: sdm845: Default qupv3_id_0 as "disabled" like _id_1
arm64: dts: msm8916: drop legacy suffix for clocks used by MSM DRM driver
arm64: dts: qcom: db820c: Add gpio-line-names property
arm64: dts: sdm845: Add rpmh-clk node
arm64: dts: sdm845: Add rpmh-rsc node
arm64: dts: qcom: sdm845: Enable debug UART and I2C10 on sdm845-mtp
arm64: dts: qcom: sdm845: Add I2C, SPI, and UART9 nodes
arm64: dts: qcom: Add pm8005 and pm8998 support
arm64: dts: qcom: Add pmu node to sdm845
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the SPDIF playback codec to the axg s400 board
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the es7154 digital to analog converter which supplies the
lienout jack of the s400
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the es7241 analog to digital converter which is fed by the
lienin jack of the s400
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the devices reponsible for managing the i2s/tdm clocks and pads
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the tdm devices responsible for serializing audio samples
for i2s/tdm interfaces
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the tdm devices responsible for decoding the data provided
through audio serial interface.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the SPDIF output device of the axg audio subsystem
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This commit adds led support for the Firefly-RK3399. The board has two
leds, this commit enables them.
Signed-off-by: Shohei Maruyama <cheat.sc.linux@outlook.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Commit 0fbc47d9e4 ("phy: rockchip-typec: deprecate some DT properties
for various register fields.") deprecates some Rockchip Type-C
properties. As these are now not needed, remove from the device tree
file.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This commit adds power button support for the Firefly-RK3399.
Signed-off-by: Shohei Maruyama <cheat.sc.linux@outlook.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the audio memory arbiter which control the access of the audio
fifos to the DDR.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The usb power regulator is supplied by the vcc 5v regulator and
controlled by a GPIO. This will be needed to enable usb.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
