there is a chance that always get response CRC error after HS200 tuning,
the reason is that need set CMD_TA to 2. this modification is only for
MT8173.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Hsin-Yi Wang <hsinyi@chromium.org>
Cc: stable@vger.kernel.org
Fixes: 1ede5cb88a ("mmc: mediatek: Use data tune for CMD line tune")
Link: https://lore.kernel.org/r/20191204071958.18553-1-chaotian.jing@mediatek.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
In cases when SDIO IRQs have been enabled, runtime suspend is prevented by
the driver. However, this still means msdc_runtime_suspend|resume() gets
called during system suspend/resume, via pm_runtime_force_suspend|resume().
This means during system suspend/resume, the register context of the mtk-sd
device most likely loses its register context, even in cases when SDIO IRQs
have been enabled.
To re-enable the SDIO IRQs during system resume, the mtk-sd driver
currently relies on the mmc core to re-enable the SDIO IRQs when it resumes
the SDIO card, but this isn't the recommended solution. Instead, it's
better to deal with this locally in the mtk-sd driver, so let's do that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO IRQ is not defaultly triggered by low level,
but by falling edge. It needs to set related register
to enable SDIO IRQ low level trigger function.
Otherwise the SDIO IRQ may be lost in some specail condition.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MSDC IP which support 64G DRAM will support 24bits BDMA buffer length,
so add support it.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when plug out SD card, may get data CRC error, the MMC core will issue
CMD13 to get card status, then CMD13 timeout(due to card plug out) will
trigger CMD19 tuning, first CMD19 timeout has not call msdc_reset_hw()
and cause the next CMD19 gets controller busy.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
SDIO IRQ is triggered by low level. It need disable SDIO IRQ
detected function. Otherwise the interrupt register can't be cleared.
It will process the interrupt more.
Signed-off-by: Jjian Zhou <jjian.zhou@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Fixes: 5215b2e952 ("mmc: mediatek: Add MMC_CAP_SDIO_IRQ support")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mtk-sd silicon has integrated card-detect logic that is
enabled on the MT7621. The circuit is phased out on newer hardware so
we should be careful to only enabled it on hardware known to support
it. This a new "use_internal_cd" flag in struct mtk_mmc_compatible.
If the sdhci isn't marked non-removable and doesn't have a
cd-gpio configured, and if use_internal_cd is set, then assume the
internal cd logic should be used as recommended by
Documentation/devicetree/bindings/mmc/mmc.txt
Signed-off-by: NeilBrown <neil@brown.name>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
When using devicetree for configuration, interrupt trigger type
should be described in the dts file, not hard-coded in the C code.
The mtk-sd silicon in the mt7621 soc uses an active-high interrupt
and so cannot be used with the current code.
So replace IRQF_TRIGGER_LOW with IRQF_TRIGGER_NONE.
Also IRQF_ONESHOT is not needed - it is used for threaded interrupt
handlers, and this driver does not used a threaded interrupt handler.
So remove that setting.
Signed-off-by: NeilBrown <neil@brown.name>
Reviewed-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
'top_base' memory region is optional. Check that the resource is valid
before using it. This avoid getting a "invalid resource" error message
printed by the kernel.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
to set cmd internal delay, need set PAD_TUNE register but not PAD_CMD_TUNE
register.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Fixes: 1ede5cb88a ("mmc: mediatek: Use data tune for CMD line tune")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the tuning code is becoming more and more bloated, let's make the
set cmd/data delay to inline function to avoid too much redundant code.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MT8183 puts the tune register at top layer, so need add new code
to support it.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
for MSDC IP which supports both data tune and async fifo, it can
tune cmd/data together. which can save the time and make the tune
result of CMD more stable as data line are 4bit or 8bit.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when msdc_cmd_is_ready return fail, the req_timeout work has not been
inited and cancel_delayed_work() will return false, then, the request
return directly and never call mmc_request_done().
so need call mod_delayed_work() before msdc_cmd_is_ready()
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
as the mmc core layer has the mmc->actual_clock, so fill it
and drop msdc_host->sclk.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
when gate MSDC0_HCLK, access register will hang, even the MSDC driver
will never accessing register after HCLK was gated, but for safety, need
gate the bus_clk(which used to access register) too.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The usage of of_device_get_match_data() reduce the code size a bit.
Also, the only way to call msdc_drv_probe() is to match an entry in
msdc_of_ids[], so of_id cannot be NULL.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just applying the existing logic and adding its own characteristics into
the space pointed by an extra entry of struct of_device_id to have support
of MT7622 SoC.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Tested-by: Jumin Li <jumin.li@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
data lines have applied to perfer to use rise edge, also need
apply it to cmd line.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
enlarge outstanding value to improve read performance
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
some platform(eg.mt2701) does not support "stop clk fix", in
this case, need set correct latch-ck to avoid crc error caused
by stop clock block-internally.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
source clock need an independent cg to control, when doing clk mode
switch, need gate source clock to avoid hw issue(multi-bit sync hw hang)
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mt2712 supports stop_clk fix and enhance_rx, which can improve
host stability.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
bit7 of PATCH_BIT1 has different meaning in new design, to
compatible with previous platform, clear this bit in new
platform.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mt2701/mt2712 supports async fifo & data tune, which can improve
host stability.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
from mt2701, the register of PAD_TUNE has been phased out,
while there is a new register of PAD_TUNE0
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the origin design of hs400_tune_response is for mt8173 because of
mt8173 has a special design. for doing that, we add a new member
"compatible", by now it's only for mt8173.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mt2701/mt2712 has 12bit clock div, which is not compatible with
mt8135/mt8173. and, some additional features will be added in
mt2701/mt2712, so that need distinguish it by comatibale name.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Bail out everytime when mmc_regulator_get_supply() returns an errno, not
only when probing gets deferred. This is currently a no-op, because this
function only returns -EPROBE_DEFER or 0 right now. But if it will throw
another error somewhen, it will be for a reason. (This still doesn't change
that getting regulators is optional, so 0 can still mean no regulators
found). So, let us a) be future proof and b) have driver code which is
easier to understand.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const. Thus the mmc_host_ops
structure itself can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };
@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p
@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
if user plug out sd card slowly, finally card is plugged out but
cat /proc/partitions can find that card is still exist in kernel.
that's because alougth get card detect interrupt but CMD13 still
can get correct response(all other pins are connected expect card
detect pin).
add ops->get_cd() can avoid this issue.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we don't select a set of better parameters for our emmc host,
It may easily occur CMD response CRC error. And also it may cause
cannot boot up issue.
Fot getting a set of better parameters, our emmc host supports
data tune mechanism.Therefore, our emmc driver also should change
to use data tune for CMD line.
Because our emmc host use the different clock source to sample the
CMD signal between HS200 and HS400 mode, the parameters are also
different between these two modes.
Separate cmd internal delay for HS200/HS400 mode.
This change can fix "System can not boot up" issue.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This patch can fix two issues:
Issue 1:
In previous code, div may be overflow when setting clock frequency
as f_min. We can use DIV_ROUND_UP to fix this boundary related
issue.
Issue 2:
In previous code, we can not set the correct clock frequency when
div equals 0xff.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
msdc_card_busy only need check if the data0 is low.
In sdio data1 irq mode, data1 may be low because of interruption.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
An mmc host driver shouldn't rely on interrupt.h being included by another
public mmc header. Instead make that dependency explicit by including
interrupt.h in those host drivers that depends on it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The void (*pre_req) callback in the struct mmc_host_ops vtable
is passing an argument "is_first_req" indicating whether this is
the first request or not.
None of the in-kernel users use this parameter: instead, since
they all just do variants of dma_map* they use the DMA cookie
to indicate whether a pre* callback has already been done for
a request when they decide how to handle it.
Delete the parameter from the callback and all users, as it is
just pointless cruft.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/mmc/host/mtk-sd.ko | grep alias
$
After this patch:
$ modinfo drivers/mmc/host/mtk-sd.ko | grep alias
alias: of:N*T*Cmediatek,mt8135-mmcC*
alias: of:N*T*Cmediatek,mt8135-mmc
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
in our host design, rise edge latching is more stable than fall edge
latching. so that if rise edge has enough margin, no need scan fall edge.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
we did not deal with the read data of CMD21/CMD19 if there is
response CRC error of CMD21/CMD19, in this case, eMMC/SD may
still in send-data state. therefore, all of next commands cannot
get response as device is not in transfer state.
for resolving this issue, still need deal with the data receive
to make device back to transfer state.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the tune result of hs200 mode at 200Mhz is not suitable for 50Mhz,
mmc_select_hs400() will set clock frequency to 50Mhz, use defalut
tune setting for 50Mhz to avoid CRC error.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
for hs400 mode, should only tune DS delay, should not
tune PAD_TUNE for data path.
if eMMC will run at hs400 mode, do not tune data while
call ops->execute_tuning().
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 9250aea76b ("mmc: core: Enable runtime PM management of host
devices"), made some calls to the runtime PM API from the driver
redundant. Especially those which deals with runtime PM reference
counting, so let's remove them.
Cc: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
