drm_bridge_remove() is for unregistering a bridge driver, not for
detaching a bridge from its consumer.
Fixes: 656fa22f9c ("drm/vc4: Switch DSI to the panel-bridge layer, and support bridges.")
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170802203242.12815-3-eric@anholt.net
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The clocks are enabled/disabled at encoder enable/disable time, not at
component load. Fixes a WARN_ON at boot if V3D fails to probe.
Fixes: 4078f57571 ("drm/vc4: Add DSI driver")
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20170802203242.12815-2-eric@anholt.net
Acked-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
The DPHY spec requires a much larger T_INIT than I was specifying
before. In the absence of clear specs from the slave of what their
timing is, just use the value that the firmware was using.
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170627195839.3338-2-eric@anholt.net
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
The newer version of the RPi panel driver is going to be a combination
of a bridge and a panel, but we should also support panels without a
bridge, so the panel-bridge layer lets us do that cleanly.
v2: Drop "dev" argument.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511183128.25085-2-eric@anholt.net
Include <drm/*.h> instead of relative path from include/drm, then
remove the -Iinclude/drm compiler flag.
While we are here, use <...> instead of "..." for include/linux/*.h
and include/sound/*.h headers too.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1495081793-9707-2-git-send-email-yamada.masahiro@socionext.com
BCM2835's PLLD_DSI1 divider doesn't give us many choices for our pixel
clocks, so to support panels on the Raspberry Pi we need to set a
higher pixel clock rate than requested and adjust the mode we program
to extend out the HFP so that the refresh rate matches.
v2: Drop an unfinished comment (caught by Noralf)
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511235625.22427-2-eric@anholt.net
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If dsi_connector fails to allocate, the exit path via label 'fail'
checks if connector is null, which it always is, so the cleanup
that destroys connector is never going to be called. Hence the
failure path can be more optimally performed by removing this
and just returning ERR_PTR(-ENOMEM). This also removes the need
to initialize connector to NULL, and we can also remove ret too.
Detected by CoverityScan, CID#1399504 ("Logicall Dead Code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170203195624.7189-1-colin.king@canonical.com
The DSI0 and DSI1 blocks on the 2835 are related hardware blocks.
Some registers move around, and the featureset is slightly different,
as DSI1 (the 4-lane DSI) is a later version of the hardware block.
This driver doesn't yet enable DSI0, since we don't have any hardware
to test against, but it does put a lot of the register definitions and
code in place.
v2: Use the clk_hw interfaces, don't set CLK_IS_BASIC (from review by
Stephen Boyd)
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/20170131192912.11316-1-eric@anholt.net
