If the given videomode does not specify DISPLAY_FLAG_* for the specific
signal property, the driver used a default value. These defaults were
never thought through, as the expectation was that all the DISPLAY_FLAGS
are always set explicitly.
With DRM bridge and panel drivers this is not the case, and while that
issue should be resolved in the future, it's still good to have sane
signal defaults.
This patch changes the defaults to what the hardware has as reset
defaults. Also, based on my experience, I think they make sense and are
more likely correct than the defaults without this patch.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200417114151.25843-1-tomi.valkeinen@ti.com
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
drivers/gpu/drm/omapdrm/dss/venc.c:211:33:
warning: 'venc_config_pal_bdghi' defined but not used [-Wunused-const-variable=]
static const struct venc_config venc_config_pal_bdghi = {
^~~~~~~~~~~~~~~~~~~~~
It is never used, remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200415132105.43636-1-yuehaibing@huawei.com
These are the usual updates for SoC specific device drivers and related
subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU and
TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=qbsP
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"These are the usual updates for SoC specific device drivers and
related subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU
and TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers"
* tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (70 commits)
soc: fsl: qe: fix sparse warnings for ucc_slow.c
soc: fsl: qe: ucc_slow: remove 0 assignment for kzalloc'ed structure
soc: fsl: qe: fix sparse warnings for ucc_fast.c
soc: fsl: qe: fix sparse warnings for qe_ic.c
soc: fsl: qe: fix sparse warnings for ucc.c
soc: fsl: qe: fix sparse warning for qe_common.c
soc: fsl: qe: fix sparse warnings for qe.c
soc: qcom: Fix QCOM_APR dependencies
soc: qcom: pdr: Avoid uninitialized use of found in pdr_indication_cb
soc: imx: drop COMPILE_TEST for IMX_SCU_SOC
firmware: imx: add COMPILE_TEST for IMX_SCU driver
soc: imx: gpc: fix power up sequencing
soc: imx: increase build coverage for imx8m soc driver
soc: qcom: apr: Add avs/audio tracking functionality
dt-bindings: soc: qcom: apr: Add protection domain bindings
soc: qcom: Introduce Protection Domain Restart helpers
devicetree: bindings: firmware: add ipq806x to qcom_scm
memory: tegra: Correct debugfs clk rate-range on Tegra124
memory: tegra: Correct debugfs clk rate-range on Tegra30
memory: tegra: Correct debugfs clk rate-range on Tegra20
...
As a result of commit 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail) and changes to various debugfs
functions in drm/core and across various drivers, there is no need for
the drm_driver.debugfs_init() hook to have a return value. Therefore,
declare it as void.
This also includes refactoring all users of the .debugfs_init() hook to
return void across the subsystem.
v2: include changes to the hook and drivers that use it in one patch to
prevent driver breakage and enable individual successful compilation of
this change.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-18-wambui.karugax@gmail.com
Since 987d65d013 (drm: debugfs: make
drm_debugfs_create_files() never fail), there is no need to ever check
the return value for drm_debugfs_create_files(). Therefore remove the
checks for the return value and subsequent error handling in
omap_debugfs_init().
These changes also enables the changing of omap_debugfs_init() to return
0 directly.
v2: convert omap_debugfs_init() to return 0 instead of void to avoid
introduction of build issues and enable individual driver compilation.
References: https://lists.freedesktop.org/archives/dri-devel/2020-February/257183.html
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200310133121.27913-14-wambui.karugax@gmail.com
drm_fb_helper_{add,remove}_one_connector() and
drm_fb_helper_single_add_all_connectors() are dummy functions now
and serve no purpose. Hence remove their calls.
This is the preparatory step for removing the
drm_fb_helper_{add,remove}_one_connector() functions from
drm_fb_helper.h
This removal is done using below sementic patch and unused variable
compilation warnings are fixed manually.
@@
@@
- drm_fb_helper_single_add_all_connectors(...);
@@
expression e1;
statement S;
@@
- e1 = drm_fb_helper_single_add_all_connectors(...);
- S
@@
@@
- drm_fb_helper_add_one_connector(...);
@@
@@
- drm_fb_helper_remove_one_connector(...);
Changes since v1:
* Squashed warning fixes into the patch that introduced the
warnings (into 5/7) (Laurent, Emil, Lyude)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-6-pankaj.laxminarayan.bharadiya@intel.com
The max connector argument for drm_fb_helper_init() isn't used anymore
hence remove it.
All the drm_fb_helper_init() calls are modified with below sementic
patch.
@@
expression E1, E2, E3;
@@
- drm_fb_helper_init(E1,E2, E3)
+ drm_fb_helper_init(E1,E2)
Signed-off-by: Pankaj Bharadiya <pankaj.laxminarayan.bharadiya@intel.com>
Reviewed-by: Emil Velikov <emil.velikov@collabora.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200305120434.111091-2-pankaj.laxminarayan.bharadiya@intel.com
In order to probe display subsystem (DSS) components with ti-sysc
interconnect target module without legacy platform data and using
devicetree, we need to update dss probing a bit.
In the device tree, we will be defining the data also for the interconnect
target modules as DSS really is a private interconnect. There is some
information about that in 4460 TRM in "Figure 10-3. DSS Integration" for
example where it mentions "32-bit interconnect (SLX)".
The changes we need to make are:
1. Parse also device tree subnodes for the compatible property fixup
2. Update the component code to consider device tree subnodes
Cc: dri-devel@lists.freedesktop.org
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap_dss_device .pre_enable(), .post_disable() and .set_timings()
are not used anymore. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-55-laurent.pinchart@ideasonboard.com
The omapdss_of_find_connected_device() function isn't used anymore,
remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-54-laurent.pinchart@ideasonboard.com
Inline the omapdss_display_get() in its only caller to simplify the
code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-53-laurent.pinchart@ideasonboard.com
The omap_connector implementation is now used for DSI only. Hardcode its
type and drop unused code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-52-laurent.pinchart@ideasonboard.com
In order to integrate with a chain of drm_bridge, the internal SDI
output has to expose its operations through the drm_bridge API.
Register a bridge at initialisation time to do so and remove the
omap_dss_device operations that are now unused.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-51-laurent.pinchart@ideasonboard.com
This makes it easier to quickly locate duplicate includes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-50-laurent.pinchart@ideasonboard.com
In order to integrate with a chain of drm_bridge, the internal DPI
output has to expose its operations through the drm_bridge API.
Register a bridge at initialisation time to do so and remove the
omap_dss_device operations that are now unused.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-49-laurent.pinchart@ideasonboard.com
The dpi_set_pll_clk() and dpi_set_dispc_clk() return various information
through pointer arguments that are never used by the callers. Remove
them to simplify the clock setting API.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-48-laurent.pinchart@ideasonboard.com
Group functions based on their purpose and split them in sections to
make the source code easier to navigate.
No functional change is included.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-47-laurent.pinchart@ideasonboard.com
This makes it easier to quickly locate duplicate includes.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-46-laurent.pinchart@ideasonboard.com
Now that the omap_dss_device EDID read operation has been removed,
simplify the bridge-based EDID access by merging multiple functions
together.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-45-laurent.pinchart@ideasonboard.com
Now that the omap_dss_device EDID read operation has been removed,
simplify the bridge-based EDID access by merging multiple functions
together.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-44-laurent.pinchart@ideasonboard.com
Now that the VENC output is driven fully through the drm_bridge API its
omap_dss_device operations are not used anymore. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-43-laurent.pinchart@ideasonboard.com
Now that the HDMI outputs are driven fully through the drm_bridge API
their omap_dss_device operations are not used anymore. Remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-42-laurent.pinchart@ideasonboard.com
Due to the removal of several omapdrm display drivers, the omapdss HPD,
detected and EDID operations are not used anymore. Remove them and all
related code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-41-laurent.pinchart@ideasonboard.com
The TPD12S015, OPA362 and analog and HDMI connectors are now supported
by DRM bridge drivers, and the omapdrm HDMI and VENC outputs can be
handled through the drm_bridge API. Switch the outputs to drm_bridge by
making the next bridge mandatory and removing the related
omapdrm-specific display drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-40-laurent.pinchart@ideasonboard.com
Use the drm_bridge_connector helper to create a connector for pipelines
that use drm_bridge. This allows splitting connector operations across
multiple bridges when necessary, instead of having the last bridge in
the chain creating the connector and handling all connector operations
internally.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-39-laurent.pinchart@ideasonboard.com
In order to integrate with a chain of drm_bridge, the internal VENC
encoder has to expose the mode valid, fixup and set, the enable and
disable and the get modes operations through the drm_bridge API.
Register a bridge at initialisation time to do so.
Most of those operations are removed from the omap_dss_device as they
are now called through the drm_bridge API by the DRM atomic helpers. The
only exception is the .get_modes() operation that is still invoked
through the omap_dss_device-based pipeline.
For the time being make the next bridge in the chain optional as the
VENC output is still based on omap_dss_device. The create_connector
argument to the bridge attach function is also ignored for the same
reason. This will be changed later when removing the related
omapdrm-specific display drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-38-laurent.pinchart@ideasonboard.com
The omapdss_hdmi_ops .set_hdmi_mode() and .set_infoframe() operations
operations are not used anymore, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-37-laurent.pinchart@ideasonboard.com
The HDMI4 encoder is transitioning to the drm_bridge API, implement the
last missing operation.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-36-laurent.pinchart@ideasonboard.com
Move the omap_dss_device .set_timings(), .enable() and .disable()
operations to the drm_bridge functions. As the drm_bridge for the HDMI
encoder is unconditionally registered and attached, those operations
will be called at the appropriate time.
The omapdss device .set_infoframe() and .set_hdmi_mode() operations have
no equivalent in drm_bridge. Thir content is thus moved to the bridge
.enable() operation as the data they store is not needed before the HDMI
encoder gets enabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-35-laurent.pinchart@ideasonboard.com
Move the omap_dss_device .set_timings(), .enable() and .disable()
operations to the drm_bridge functions. As the drm_bridge for the HDMI
encoder is unconditionally registered and attached, those operations
will be called at the appropriate time.
The omapdss device .set_infoframe() and .set_hdmi_mode() operations have
no equivalent in drm_bridge. Thir content is thus moved to the bridge
.enable() operation as the data they store is not needed before the HDMI
encoder gets enabled.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-34-laurent.pinchart@ideasonboard.com
In order to integrate with a chain of drm_bridge, the internal HDMI5
encoder has to expose the EDID read operation through the drm_bridge
API. Register a bridge at initialisation time to do so.
For the time being make the next bridge in the chain optional as the
HDMI output is still based on omap_dss_device. The create_connector
argument to the bridge attach function is also ignored for the same
reason. This will be changed later when removing the related
omapdrm-specific display drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-33-laurent.pinchart@ideasonboard.com
In order to integrate with a chain of drm_bridge, the internal HDMI4
encoder has to expose the EDID read operation through the drm_bridge
API. Register a bridge at initialisation time to do so.
For the time being make the next bridge in the chain optional as the
HDMI output is still based on omap_dss_device. The create_connector
argument to the bridge attach function is also ignored for the same
reason. This will be changed later when removing the related
omapdrm-specific display drivers.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-32-laurent.pinchart@ideasonboard.com
In preparation of adding DRM bridge support to the hdmi5 encoder code,
rework the EDID read to isolate data read.
The hdmi_read_edid() function is the main entry point. It performs all
initialisation steps required prior to reading the EDID (such as
ensuring the device is powered on), as well as corresponding cleanup
steps afterwards. EDID read itself is handled by hdmi_read_edid_data()
that calls the hdmi5_core_ddc_read() function to read individual blocks.
This new code architecture will allow reusing hdmi_read_edid() and
hdmi5_core_ddc_read() for the drm_bridge EDID read implementation, while
swapping out hdmi_read_edid_data() for the DRM drm_do_get_edid()
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-31-laurent.pinchart@ideasonboard.com
In preparation of adding DRM bridge support to the hdmi4 encoder code,
rework the EDID read to isolate data read.
The hdmi_read_edid() function is the main entry point. It performs all
initialisation steps required prior to reading the EDID (such as
ensuring the device is powered on), as well as corresponding cleanup
steps afterwards. EDID read itself is handled by hdmi_read_edid_data()
that calls the hdmi4_core_ddc_read() function to read individual blocks.
This new code architecture will allow reusing hdmi_read_edid() and
hdmi4_core_ddc_read() for the drm_bridge EDID read implementation, while
swapping out hdmi_read_edid_data() for the DRM drm_do_get_edid()
function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-30-laurent.pinchart@ideasonboard.com
Bring the omapdss-specific .read_edid() operation in sync with the
drm_bridge .get_edid() operation to ease code reuse.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-29-laurent.pinchart@ideasonboard.com
As part of the move to drm_bridge ops, the dssdev ops will become empty
for some of the internal encoders. Make them optional in the driver to
allow them to be removed completely, easing the transition.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-28-laurent.pinchart@ideasonboard.com
In order to support drm_bridge-based pipeline, the internal HDMI
encoders will need to expose the EDID read operation through the
drm_bridge API, and thus to expose a drm_bridge instance corresponding
to the encoder. The HDMI encoders are however handled as omap_dss_device
instances, which conflicts with this requirement.
In order to move forward with the drm_bridge transition, add support for
creating drm_bridge instances local to DSS outputs. If a local bridge is
passed to the omapdss_device_init_output() function, it is used as the
first bridge in the chain, and the omap_dss_device.next_bridge field is
set to the next bridge for the use of the internal encoders' bridges.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-27-laurent.pinchart@ideasonboard.com
The DSS core looks up the next device connected to an output by
traversing the OF graph. It currently hardcodes the local port number to
0, which breaks any output with a different port number (SDI on OMAP3
and any DPI output but the first one). Fix this by repurposing the
currently unused of_ports bitmask in omap_dss_device with an of_port
output port number, and use it to traverse the OF graph.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-26-laurent.pinchart@ideasonboard.com
Replace the manual panel handling code by a drm_panel_bridge. This
simplifies the driver and allows all components in the display pipeline
to be treated as bridges, paving the way to generic connector handling.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-25-laurent.pinchart@ideasonboard.com
Move the code that computes the DRM connector type for the
omapdss_device display type to a new omapdss_device_connector_type()
function for later reuse.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-24-laurent.pinchart@ideasonboard.com
Remove the omap_connector_get_hdmi_mode() function as the HDMI mode can
be accessed directly from the connector's display info.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-23-laurent.pinchart@ideasonboard.com
When the DSS initialises its output DPI and SDI ports, failures don't
clean up previous successfully initialised ports. This can lead to
resource leak or memory corruption. Fix it.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-22-laurent.pinchart@ideasonboard.com
Most bridge drivers create a DRM connector to model the connector at the
output of the bridge. This model is historical and has worked pretty
well so far, but causes several issues:
- It prevents supporting more complex display pipelines where DRM
connector operations are split over multiple components. For instance a
pipeline with a bridge connected to the DDC signals to read EDID data,
and another one connected to the HPD signal to detect connection and
disconnection, will not be possible to support through this model.
- It requires every bridge driver to implement similar connector
handling code, resulting in code duplication.
- It assumes that a bridge will either be wired to a connector or to
another bridge, but doesn't support bridges that can be used in both
positions very well (although there is some ad-hoc support for this in
the analogix_dp bridge driver).
In order to solve these issues, ownership of the connector should be
moved to the display controller driver (where it can be implemented
using helpers provided by the core).
Extend the bridge API to allow disabling connector creation in bridge
drivers as a first step towards the new model. The new flags argument to
the bridge .attach() operation allows instructing the bridge driver to
skip creating a connector. Unconditionally set the new flags argument to
0 for now to keep the existing behaviour, and modify all existing bridge
drivers to return an error when connector creation is not requested as
they don't support this feature yet.
The change is based on the following semantic patch, with manual review
and edits.
@ rule1 @
identifier funcs;
identifier fn;
@@
struct drm_bridge_funcs funcs = {
...,
.attach = fn
};
@ depends on rule1 @
identifier rule1.fn;
identifier bridge;
statement S, S1;
@@
int fn(
struct drm_bridge *bridge
+ , enum drm_bridge_attach_flags flags
)
{
... when != S
+ if (flags & DRM_BRIDGE_ATTACH_NO_CONNECTOR) {
+ DRM_ERROR("Fix bridge driver to make connector optional!");
+ return -EINVAL;
+ }
+
S1
...
}
@ depends on rule1 @
identifier rule1.fn;
identifier bridge, flags;
expression E1, E2, E3;
@@
int fn(
struct drm_bridge *bridge,
enum drm_bridge_attach_flags flags
) {
<...
drm_bridge_attach(E1, E2, E3
+ , flags
)
...>
}
@@
expression E1, E2, E3;
@@
drm_bridge_attach(E1, E2, E3
+ , 0
)
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226112514.12455-10-laurent.pinchart@ideasonboard.com
The call to of_find_matching_node returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
drivers/gpu/drm/omapdrm/dss/omapdss-boot-init.c:212:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 209, but without a corresponding object release within this function.
drivers/gpu/drm/omapdrm/dss/omapdss-boot-init.c:237:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 209, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Cc: Markus Elfring <Markus.Elfring@web.de>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1554692313-28882-2-git-send-email-wen.yang99@zte.com.cn
Instead of dma_dev->device_prep_dma_memcpy() use the existing macro to
prepare the memcpy.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190731094233.13890-2-peter.ujfalusi@ti.com
Fixes coccicheck warning:
drivers/gpu/drm/omapdrm/displays/panel-dsi-cm.c:681:1-15: WARNING: Assignment of 0/1 to bool variable
drivers/gpu/drm/omapdrm/displays/panel-dsi-cm.c:732:1-15: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Bin <zhengbin13@huawei.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1579763123-62749-1-git-send-email-zhengbin13@huawei.com
Since the if statement only checks for the value of the `id` variable,
it can be replaced by the more concise BUG_ON() macro for error
reporting.
Issue found using coccinelle.
Signed-off-by: Wambui Karuga <wambui.karugax@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200102095515.7106-1-wambui.karugax@gmail.com
