Improve performance for the relevant systems and remove the DMA ordering
barrier from `readX_relaxed' and `writeX_relaxed' MMIO accessors, where
it is not needed according to our requirements[1]. For consistency make
the same arrangement with low-level port I/O accessors, but do not
actually provide any accessors making use of it.
References:
[1] "LINUX KERNEL MEMORY BARRIERS", Documentation/memory-barriers.txt,
Section "KERNEL I/O BARRIER EFFECTS"
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20865/
Cc: Ralf Baechle <ralf@linux-mips.org>
Architecturally the MIPS ISA does not specify ordering requirements for
uncached bus accesses such as MMIO operations normally use and therefore
explicit barriers have to be inserted between MMIO accesses where
unspecified ordering of operations would cause unpredictable results.
For example the R2020 write buffer implements write gathering and
combining[1] and as used with the DECstation models 2100 and 3100 for
MMIO accesses it bypasses the read buffer entirely, because conflicts
are resolved by the memory controller for DRAM accesses only[2] (NB the
R2020 and R3020 buffers are the same except for the maximum clock rate).
Consequently if a device has say a 16-bit control register at offset 0,
a 16-bit event mask register at offset 2 and a 16-bit reset register at
offset 4, and the initial value of the control register is 0x1111, then
in the absence of barriers a hypothetical code sequence like this:
u16 init_dev(u16 __iomem *dev);
u16 x;
write16(dev + 2, 0xffff);
write16(dev + 0, 0x2222);
x = read16(dev + 0);
write16(dev + 1, 0x3333);
write16(dev + 0, 0x4444);
return x;
}
will return 0x1111 and issue a single 32-bit write of 0x33334444 (in the
little-endian bus configuration) to offset 0 on the system bus.
This is because the read to set `x' from offset 0 bypasses the write of
0x2222 that is still in the write buffer pending the completion of the
write of 0xffff to the reset register. Then the write of 0x3333 to the
event mask register is merged with the preceding write to the control
register as they share the same word address, making it a 32-bit write
of 0x33332222 to offset 0. Finally the write of 0x4444 to the control
register is combined with the outstanding 32-bit write of 0x33332222 to
offset 0, because, again, it shares the same address.
This is an example from a legacy system, given here because it is well
documented and affects a machine we actually support. But likewise
modern MIPS systems may implement weak MMIO ordering, possibly even
without having it clearly documented except for being compliant with the
architecture specification with respect to the currently defined SYNC
instruction variants[3].
Considering the above and that we are required to implement MMIO
accessors such that individual accesses made with them are strongly
ordered with respect to each other[4], add the necessary barriers to our
`inX', `outX', `readX' and `writeX' handlers, as well the associated
special use variants. It's up to platforms then to possibly define the
respective barriers so as to expand to nil if no ordering enforcement is
actually needed for a given system; SYNC is supposed to be as cheap as
a NOP on strongly ordered MIPS implementations though.
Retain the option to generate weakly-ordered accessors, so that the
arrangement for `war_io_reorder_wmb' is not lost in case we need it for
fully raw accessors in the future. The reason for this is that it is
unclear from commit 1e820da3c9 ("MIPS: Loongson-3: Introduce
CONFIG_LOONGSON3_ENHANCEMENT") and especially commit 8faca49a67
("MIPS: Modify core io.h macros to account for the Octeon Errata
Core-301.") why they are needed there under the previous assumption that
these accessors can be weakly ordered.
References:
[1] "LR3020 Write Buffer", LSI Logic Corporation, September 1988,
Section "Byte Gathering", pp. 6-7
[2] "DECstation 3100 Desktop Workstation Functional Specification",
Digital Equipment Corporation, Revision 1.3, August 28, 1990,
Section 6.1 "Processor", p. 4
[3] "MIPS Architecture For Programmers, Volume II-A: The MIPS32
Instruction Set Manual", Imagination Technologies LTD, Document
Number: MD00086, Revision 6.06, December 15, 2016, Table 5.5
"Encodings of the Bits[10:6] of the SYNC instruction; the SType
Field", p. 409
[4] "LINUX KERNEL MEMORY BARRIERS", Documentation/memory-barriers.txt,
Section "KERNEL I/O BARRIER EFFECTS"
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
References: 8faca49a67 ("MIPS: Modify core io.h macros to account for the Octeon Errata Core-301.")
References: 1e820da3c9 ("MIPS: Loongson-3: Introduce CONFIG_LOONGSON3_ENHANCEMENT")
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20864/
Cc: Ralf Baechle <ralf@linux-mips.org>
Redefine `mmiowb' in terms of `iobarrier_w' so that it works correctly
for MIPS I platforms, which have no SYNC machine instruction and use a
call to `wbflush' instead.
This doesn't change the semantics for CONFIG_CPU_CAVIUM_OCTEON, because
`iobarrier_w' expands to `wmb', which is ultimately the same as the
current arrangement. For MIPS I platforms this not only makes any code
that would happen to use `mmiowb' build and run, but it actually
enforces the ordering required as well, as `iobarrier_w' has it already
covered with the use of `wmb'.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20863/
Cc: Ralf Baechle <ralf@linux-mips.org>
Define MMIO ordering barriers as separate operations so as to allow
making places where such a barrier is required distinct from places
where a memory or a DMA barrier is needed.
Architecturally MIPS does not specify ordering requirements for uncached
bus accesses such as MMIO operations normally use and therefore explicit
barriers have to be inserted between MMIO accesses where unspecified
ordering of operations would cause unpredictable results.
MIPS MMIO ordering barriers are implemented using the same underlying
mechanism that memory or a DMA barrier ordering barriers use, that is
either a suitable SYNC instruction or a platform-specific `wbflush'
call. However platforms may implement different ordering rules for
different kinds of bus activity, so having a separate API makes it
possible to remove unnecessary barriers and avoid a performance hit they
may cause due to unrelated bus activity by making their implementation
expand to nil while keeping the necessary ones.
Also having distinct barriers for each kind of use makes it easier for
the reader to understand what code has been intended to do.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20862/
Cc: Ralf Baechle <ralf@linux-mips.org>
Rewrite to use the `reorder' assembly mode and remove manually scheduled
delay slots except where GAS cannot schedule a delay-slot instruction
due to a data dependency or a section switch (as is the case with the EX
macro). No change in machine code produced.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
[paul.burton@mips.com:
Fix conflict with commit 932afdeec1 ("MIPS: Add Kconfig variable for
CPUs with unaligned load/store instructions")]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20834/
Cc: Ralf Baechle <ralf@linux-mips.org>
Fix a commit 8a8158c85e ("MIPS: memset.S: EVA & fault support for
small_memset") regression and remove assembly warnings:
arch/mips/lib/memset.S: Assembler messages:
arch/mips/lib/memset.S:243: Warning: Macro instruction expanded into multiple instructions in a branch delay slot
triggering with the CPU_DADDI_WORKAROUNDS option set and this code:
PTR_SUBU a2, t1, a0
jr ra
PTR_ADDIU a2, 1
This is because with that option in place the DADDIU instruction, which
the PTR_ADDIU CPP macro expands to, becomes a GAS macro, which in turn
expands to an LI/DADDU (or actually ADDIU/DADDU) sequence:
13c: 01a4302f dsubu a2,t1,a0
140: 03e00008 jr ra
144: 24010001 li at,1
148: 00c1302d daddu a2,a2,at
...
Correct this by switching off the `noreorder' assembly mode and letting
GAS schedule this jump's delay slot, as there is nothing special about
it that would require manual scheduling. With this change in place
correct code is produced:
13c: 01a4302f dsubu a2,t1,a0
140: 24010001 li at,1
144: 03e00008 jr ra
148: 00c1302d daddu a2,a2,at
...
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 8a8158c85e ("MIPS: memset.S: EVA & fault support for small_memset")
Patchwork: https://patchwork.linux-mips.org/patch/20833/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: stable@vger.kernel.org # 4.17+
The Microsemi Ocelot has a set of register for SerDes/switch port muxing
as well as PCIe muxing for a specific SerDes, so let's add the device
and all SerDes in the Device Tree.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HSIO contains registers for PLL5 configuration, SerDes/switch port
muxing and a thermal sensor, hence we can't keep it in the switch DT
node.
Acked-by: Paul Burton <paul.burton@mips.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a commit 8a8158c85e ("MIPS: memset.S: EVA & fault support for
small_memset") regression and remove assembly warnings:
arch/mips/lib/memset.S: Assembler messages:
arch/mips/lib/memset.S:243: Warning: Macro instruction expanded into multiple instructions in a branch delay slot
triggering with the CPU_DADDI_WORKAROUNDS option set and this code:
PTR_SUBU a2, t1, a0
jr ra
PTR_ADDIU a2, 1
This is because with that option in place the DADDIU instruction, which
the PTR_ADDIU CPP macro expands to, becomes a GAS macro, which in turn
expands to an LI/DADDU (or actually ADDIU/DADDU) sequence:
13c: 01a4302f dsubu a2,t1,a0
140: 03e00008 jr ra
144: 24010001 li at,1
148: 00c1302d daddu a2,a2,at
...
Correct this by switching off the `noreorder' assembly mode and letting
GAS schedule this jump's delay slot, as there is nothing special about
it that would require manual scheduling. With this change in place
correct code is produced:
13c: 01a4302f dsubu a2,t1,a0
140: 24010001 li at,1
144: 03e00008 jr ra
148: 00c1302d daddu a2,a2,at
...
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 8a8158c85e ("MIPS: memset.S: EVA & fault support for small_memset")
Patchwork: https://patchwork.linux-mips.org/patch/20833/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: stable@vger.kernel.org # 4.17+
Rework the defintion of struct siginfo so that the array padding
struct siginfo to SI_MAX_SIZE can be placed in a union along side of
the rest of the struct siginfo members. The result is that we no
longer need the __ARCH_SI_PREAMBLE_SIZE or SI_PAD_SIZE definitions.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
platform_nand_xxx definitions are just used by the plat_nand driver.
Let's move those definitions out of the core/driver-agnostic rawnand.h
header.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
We regularly have new NAND controller drivers that are making use of
fields/hooks that we want to get rid of but can't because of all the
legacy drivers that we might break if we do.
So, instead of removing those fields/hooks, let's move them to a
sub-struct which is clearly documented as deprecated.
We start with the ->IO_ADDR_{R,W] fields.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Let's make the raw NAND API consistent by patching all helpers and
hooks to take a nand_chip object instead of an mtd_info one or
remove the mtd_info object when both are passed.
In order to do that, we first need to update the platform_nand_ctrl
hooks to take a nand_chip object instead of an mtd_info.
We add temporary plat_nand_xxx() wrappers to the do the mtd -> chip
conversion, but those will be dropped when patching nand_chip hooks to
take a nand_chip object.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Krzysztof Halasa <khalasa@piap.pl>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add the ISO7816 ioctl and associated accessors and data structure.
Drivers can then use this common implementation to handle ISO7816
(smart cards).
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
[ludovic.desroches@microchip.com: squash and rebase, removal of gpios, checkpatch fixes]
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is nothing arch specific about building dtb files other than their
location under /arch/*/boot/dts/. Keeping each arch aligned is a pain.
The dependencies and supported targets are all slightly different.
Also, a cross-compiler for each arch is needed, but really the host
compiler preprocessor is perfectly fine for building dtbs. Move the
build rules to a common location and remove the arch specific ones. This
is done in a single step to avoid warnings about overriding rules.
The build dependencies had been a mixture of 'scripts' and/or 'prepare'.
These pull in several dependencies some of which need a target compiler
(specifically devicetable-offsets.h) and aren't needed to build dtbs.
All that is really needed is dtc, so adjust the dependencies to only be
dtc.
This change enables support 'dtbs_install' on some arches which were
missing the target.
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-kbuild@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: uclinux-h8-devel@lists.sourceforge.jp
Cc: linux-mips@linux-mips.org
Cc: nios2-dev@lists.rocketboards.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-xtensa@linux-xtensa.org
Signed-off-by: Rob Herring <robh@kernel.org>
Commit 8ce355cf2e ("MIPS: Setup boot_command_line before
plat_mem_setup") fixed a problem for systems which have
CONFIG_CMDLINE_BOOL=y & use a DT with a chosen node that has either no
bootargs property or an empty one. In this configuration
early_init_dt_scan_chosen() copies CONFIG_CMDLINE into
boot_command_line, but the MIPS code doesn't know this so it appends
CONFIG_CMDLINE (via builtin_cmdline) to boot_command_line again. The
result is that boot_command_line contains the arguments from
CONFIG_CMDLINE twice.
That commit took the approach of simply setting up boot_command_line
from the MIPS code before early_init_dt_scan_chosen() runs, causing it
not to copy CONFIG_CMDLINE to boot_command_line if a chosen node with no
bootargs property is found.
Unfortunately this is problematic for systems which do have a non-empty
bootargs property & CONFIG_CMDLINE_BOOL=y. There
early_init_dt_scan_chosen() will overwrite boot_command_line with the
arguments from DT, which means we lose those from CONFIG_CMDLINE
entirely. This breaks CONFIG_MIPS_CMDLINE_DTB_EXTEND. If we have
CONFIG_MIPS_CMDLINE_FROM_BOOTLOADER or
CONFIG_MIPS_CMDLINE_BUILTIN_EXTEND selected and the DT has a bootargs
property which we should ignore, it will instead be honoured breaking
those configurations too.
Fix this by reverting commit 8ce355cf2e ("MIPS: Setup
boot_command_line before plat_mem_setup") to restore the former
behaviour, and fixing the CONFIG_CMDLINE duplication issue by
initializing boot_command_line to a non-empty string that
early_init_dt_scan_chosen() will not overwrite with CONFIG_CMDLINE.
This is a little ugly, but cleanup in this area is on its way. In the
meantime this is at least easy to backport & contains the ugliness
within arch/mips/.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 8ce355cf2e ("MIPS: Setup boot_command_line before plat_mem_setup")
References: https://patchwork.linux-mips.org/patch/18804/
Patchwork: https://patchwork.linux-mips.org/patch/20813/
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: Jaedon Shin <jaedon.shin@gmail.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.16+
When using the legacy mmap layout, for example triggered using ulimit -s
unlimited, get_unmapped_area() fills memory from bottom to top starting
from a fairly low address near TASK_UNMAPPED_BASE.
This placement is suboptimal if the user application wishes to allocate
large amounts of heap memory using the brk syscall. With the VDSO being
located low in the user's virtual address space, the amount of space
available for access using brk is limited much more than it was prior to
the introduction of the VDSO.
For example:
# ulimit -s unlimited; cat /proc/self/maps
00400000-004ec000 r-xp 00000000 08:00 71436 /usr/bin/coreutils
004fc000-004fd000 rwxp 000ec000 08:00 71436 /usr/bin/coreutils
004fd000-0050f000 rwxp 00000000 00:00 0
00cc3000-00ce4000 rwxp 00000000 00:00 0 [heap]
2ab96000-2ab98000 r--p 00000000 00:00 0 [vvar]
2ab98000-2ab99000 r-xp 00000000 00:00 0 [vdso]
2ab99000-2ab9d000 rwxp 00000000 00:00 0
...
Resolve this by adjusting STACK_TOP to reserve space for the VDSO &
providing an address hint to get_unmapped_area() causing it to use this
space even when using the legacy mmap layout.
We reserve enough space for the VDSO, plus 1MB or 256MB for 32 bit & 64
bit systems respectively within which we randomize the VDSO base
address. Previously this randomization was taken care of by the mmap
base address randomization performed by arch_mmap_rnd(). The 1MB & 256MB
sizes are somewhat arbitrary but chosen such that we have some
randomization without taking up too much of the user's virtual address
space, which is often in short supply for 32 bit systems.
With this the VDSO is always mapped at a high address, leaving lots of
space for statically linked programs to make use of brk:
# ulimit -s unlimited; cat /proc/self/maps
00400000-004ec000 r-xp 00000000 08:00 71436 /usr/bin/coreutils
004fc000-004fd000 rwxp 000ec000 08:00 71436 /usr/bin/coreutils
004fd000-0050f000 rwxp 00000000 00:00 0
00c28000-00c49000 rwxp 00000000 00:00 0 [heap]
...
7f67c000-7f69d000 rwxp 00000000 00:00 0 [stack]
7f7fc000-7f7fd000 rwxp 00000000 00:00 0
7fcf1000-7fcf3000 r--p 00000000 00:00 0 [vvar]
7fcf3000-7fcf4000 r-xp 00000000 00:00 0 [vdso]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Huacai Chen <chenhc@lemote.com>
Fixes: ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
Cc: Huacai Chen <chenhc@lemote.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.4+
gcc 3.3 has been retired for a while, use PTRS_PER_PGD and remove the
asm-offsets.h inclusion.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20814/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
The crash utility initializes cpu state by reading the system kernel
memory, which is copied into vmcore.
It is also natural to preserve the online state for CPUs at crash.
Failing to do so could make the analysis tool present info for only 1 CPU
by default, and unable to find panic task.
Signed-off-by: Dengcheng Zhu <dzhu@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20809/
Cc: Paul Burton <pburton@wavecomp.com>
Cc: "ralf@linux-mips.org" <ralf@linux-mips.org>
Cc: "linux-mips@linux-mips.org" <linux-mips@linux-mips.org>
Cc: "rachel.mozes@intel.com" <rachel.mozes@intel.com>
In much the same vein as commit ac41f9c462 ("MIPS: Remove a temporary
hack for debugging cache flushes in SMTC configuration") and commit
eb75ecb113 ("MIPS: MT: Remove unused MT single-threaded cache flush
code"), remove the long obsolete ndflush & niflush command line
arguments which provided a hack that should not be useful outside of
debug sessions performed long ago.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Commit ac41f9c462 ("MIPS: Remove a temporary hack for debugging cache
flushes in SMTC configuration") removed an ugly hack that allowed cache
flushing to be performed single-threaded, something which should not be
necessary outside of debug sessions performed long ago.
Whilst the hack was removed from the cache flush code itself, the
mt_protdflush & mt_protiflush variables were left behind along with code
providing the protdflush & protiflush command line arguments. The
mt_cflush_lockdown() & mt_cflush_release() functions were also left
behind but are now entirely unused.
Remove all the unused code to complete the removal of the MT ASE
single-threaded cache flush hack.
Signed-off-by: Paul Burton <paul.burton@mips.com>
MIPSR6 CPUs do not support unaligned load/store instructions
(LWL, LWR, SWL, SWR and LDL, LDR, SDL, SDR for 64bit).
Currently the MIPS tree has some special cases to avoid these
instructions, and the code is testing for !CONFIG_CPU_MIPSR6.
This patch declares a new Kconfig variable:
CONFIG_CPU_HAS_LOAD_STORE_LR.
This variable indicates that the CPU supports these instructions.
Then, the patch does the following:
- Carefully selects this option on all CPUs except MIPSR6.
- Switches all the special cases to test for the new variable,
and inverts the logic:
'#ifndef CONFIG_CPU_MIPSR6' turns into
'#ifdef CONFIG_CPU_HAS_LOAD_STORE_LR'
and vice-versa.
Also, when this variable is NOT selected (e.g. MIPSR6),
CONFIG_GENERIC_CSUM will default to 'y', to compile generic
C checksum code (instead of special assembly code that uses the
unsupported instructions).
This commit should not affect any existing CPU, and is required
for future Lexra CPU support, that misses these instructions too.
Signed-off-by: Yasha Cherikovsky <yasha.che3@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20808/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
The ELF appended dtb can be accessed now via 'fw_passed_dtb'.
Since raw appended dtb is accessed via that variable too,
this now effectively allows to boot with CONFIG_MIPS_RAW_APPENDED_DTB=y
on Octeon.
Signed-off-by: Yasha Cherikovsky <yasha.che3@gmail.com>
[paul.burton@mips.com: Fix trivial __dtb_octeon_*_begin conflict]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20805/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Since commit 15f37e1588 ("MIPS: store the appended
dtb address in a variable"),
in kernels with MIPS_RAW_APPENDED_DTB=y, the early boot code detects
the dtb and stores it in the 'fw_passed_dtb' variable.
However, the dtb is not stored in 'fw_passed_dtb' in kernels with
MIPS_ELF_APPENDED_DTB=y.
Under MIPS_ELF_APPENDED_DTB=y, the dtb is also located in the
__appended_dtb section, so we just need to update the #ifdef.
This will allow to access the dtb in a more uniform way.
Fixes: 15f37e1588 ("MIPS: store the appended dtb address in a variable")
Signed-off-by: Yasha Cherikovsky <yasha.che3@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20803/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
It makes the code more readable, especially in the nested ifdefs.
Signed-off-by: Yasha Cherikovsky <yasha.che3@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20802/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Out-of-tree platforms may not be based on Generic as shown in customer
communication. Share the prepare method with all using UHI boot protocol,
and put into machine_kexec.c.
The benefit is that, when having kexec_args related problems, developers
will naturally look into machine_kexec.c, where "CONFIG_UHI_BOOT" will be
found, prompting them to add "select UHI_BOOT" to the platform Kconfig. It
would otherwise require a lot debugging or online searching to be aware
that the solution is in Generic code.
Tested-by: Rachel Mozes <rachel.mozes@intel.com>
Reported-by: Rachel Mozes <rachel.mozes@intel.com>
Signed-off-by: Dengcheng Zhu <dzhu@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20569/
Cc: pburton@wavecomp.com
Cc: ralf@linux-mips.org
Cc: linux-mips@linux-mips.org
We can rely on the system kernel and the dump capture kernel themselves in
memory usage.
Being restrictive with 512MB limit may cause kexec tool failure on some
platforms.
Tested-by: Rachel Mozes <rachel.mozes@intel.com>
Reported-by: Rachel Mozes <rachel.mozes@intel.com>
Signed-off-by: Dengcheng Zhu <dzhu@wavecomp.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20568/
Cc: pburton@wavecomp.com
Cc: ralf@linux-mips.org
Cc: linux-mips@linux-mips.org
The existing implementation lets machine_kexec() CPU jump to reboot code
buffer, whereas other CPUs to relocated_kexec_smp_wait. The natural way to
bring up an SMP new kernel would be to let CPU0 do it while others being
halted. For those failing to do so, fall back to the jumping method.
Signed-off-by: Dengcheng Zhu <dzhu@wavecomp.com>
[paul.burton@mips.com: Guard kexec_nonboot_cpu_jump with CONFIG_SMP]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20570/
Cc: pburton@wavecomp.com
Cc: ralf@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: rachel.mozes@intel.com
The only functional differences (modulo a few missing fixes in the arch
code) is that architectures without coherent caches need a hook to
convert a virtual or dma address into a pfn, given that we don't have
the kernel linear mapping available for the otherwise easy virt_to_page
call. As a side effect we can support mmap of the per-device coherent
area even on architectures not providing the callback, and we make
previous dangerous default methods dma_common_mmap actually save for
non-coherent architectures by rejecting it without the right helper.
In addition to that we need a hook so that some architectures can
override the protection bits when mmaping a dma coherent allocations.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS parts
All the cache maintainance is already stubbed out when not enabled,
but merging the two allows us to nicely handle the case where
cache maintainance is required for some devices, but not others.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com> # MIPS parts
Various architectures support both coherent and non-coherent dma on a
per-device basis. Move the dma_noncoherent flag from the mips archdata
field to struct device proper to prepare the infrastructure for reuse on
other architectures.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While both option select a form of conditional dma coherence they don't
actually share any code in the implementation, so untangle them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Original Loongson-3 pci_ops can only access standard pci config space,
this patch let it be able to access extended pci config space.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
[paul.burton@mips.com: Tweaks to fix checkpatch warnings, reverse xmas tree]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20707/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
New Loongson-3 (Loongson-3A R2, Loongson-3A R3, and newer) has SFB
(Store Fill Buffer) which can improve the performance of memory access.
Now, SFB enablement is controlled by CONFIG_LOONGSON3_ENHANCEMENT, and
the generic kernel has no benefit from SFB (even it is running on a new
Loongson-3 machine). With this patch, we can enable SFB at runtime by
detecting the CPU type (the expense is war_io_reorder_wmb() will always
be a 'sync', which will hurt the performance of old Loongson-3).
[paul.burton@mips.com: Further info from Huacai:
In practise, I found that sometimes there are boot failures if I
enable SFB/LPA in cpu_probe(). I don't know why because processor
designers also haven't give me an explaination, but I think this may
have some relationships to speculative execution.]
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20426/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
Call pcie_bus_configure_settings() on MIPS, like for other platforms.
The function pcie_bus_configure_settings() makes sure the MPS (Max
Payload Size) across the bus is uniform and provides the ability to
tune the MRSS (Max Read Request Size) and MPS (Max Payload Size) to
higher performance values. Some devices will not operate properly if
these aren't set correctly because the firmware doesn't always do it.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20649/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
This API is not used anywhere in the kernel and has remained
unused for years after being introduced.
Over time, we have developed a subsystem to deal with pin
control and this now managed pull up/down.
Delete the old and unused API. If this platform needs it,
we should implement a proper pin controller for it instead.
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MIPS already has memblock support and all the memory is already registered
with it.
This patch replaces bootmem memory reservations with memblock ones and
removes the bootmem initialization.
Since memblock allocates memory in top-down mode, we ensure that memblock
limit is max_low_pfn to prevent allocations from the high memory.
To have the exceptions base in the lower 512M of the physical memory, its
allocation in arch/mips/kernel/traps.c::traps_init() is using bottom-up
mode.
Signed-off-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20560/
Cc: Serge Semin <fancer.lancer@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-mm@kvack.org
Cc: linux-kernel@vger.kernel.org
This adds the DSA driver for the GSWIP Switch found in the VRX200 SoC.
This switch is integrated in the DSL SoC, this SoC uses a GSWIP version
2.1, there are other SoCs using different versions of this IP block, but
this driver was only tested with the version found in the VRX200.
Currently only the basic features are implemented which will forward all
packages to the CPU and let the CPU do the forwarding. The hardware also
support Layer 2 offloading which is not yet implemented in this driver.
The GPHY FW loaded is now done by this driver and not any more by the
separate driver in drivers/soc/lantiq/gphy.c, I will remove this driver
is a separate patch. to make use of the GPHY this switch driver is
needed anyway. Other SoCs have more embedded GPHYs so this driver should
support a variable number of GPHYs. After the firmware was loaded the
GPHY can be probed on the MDIO bus and it behaves like an external GPHY,
without the firmware it can not be probed on the MDIO bus.
The clock names in the sysctrl.c file have to be changed because the
clocks are now used by a different driver. This should be cleaned up and
a real common clock driver should provide the clocks instead.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This drives the PMAC between the GSWIP Switch and the CPU in the VRX200
SoC. This is currently only the very basic version of the Ethernet
driver.
When the DMA channel is activated we receive some packets which were
send to the SoC while it was still in U-Boot, these packets have the
wrong header. Resetting the IP cores did not work so we read out the
extra packets at the beginning and discard them.
This also adapts the clock code in sysctrl.c to use the default name of
the device node so that the driver gets the correct clock. sysctrl.c
should be replaced with a proper common clock driver later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DMA channel is opened the IRQ should not get activated
automatically, this allows it to pull data out manually without the help
of interrupts. This is needed for a workaround in the vrx200 Ethernet
driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix up several Kconfig dependencies in netfilter, from Martin Willi
and Florian Westphal.
2) Memory leak in be2net driver, from Petr Oros.
3) Memory leak in E-Switch handling of mlx5 driver, from Raed Salem.
4) mlx5_attach_interface needs to check for errors, from Huy Nguyen.
5) tipc_release() needs to orphan the sock, from Cong Wang.
6) Need to program TxConfig register after TX/RX is enabled in r8169
driver, not beforehand, from Maciej S. Szmigiero.
7) Handle 64K PAGE_SIZE properly in ena driver, from Netanel Belgazal.
8) Fix crash regression in ip_do_fragment(), from Taehee Yoo.
9) syzbot can create conditions where kernel log is flooded with
synflood warnings due to creation of many listening sockets, fix
that. From Willem de Bruijn.
10) Fix RCU issues in rds socket layer, from Cong Wang.
11) Fix vlan matching in nfp driver, from Pieter Jansen van Vuuren.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
nfp: flower: reject tunnel encap with ipv6 outer headers for offloading
nfp: flower: fix vlan match by checking both vlan id and vlan pcp
tipc: check return value of __tipc_dump_start()
s390/qeth: don't dump past end of unknown HW header
s390/qeth: use vzalloc for QUERY OAT buffer
s390/qeth: switch on SG by default for IQD devices
s390/qeth: indicate error when netdev allocation fails
rds: fix two RCU related problems
r8169: Clear RTL_FLAG_TASK_*_PENDING when clearing RTL_FLAG_TASK_ENABLED
erspan: fix error handling for erspan tunnel
erspan: return PACKET_REJECT when the appropriate tunnel is not found
tcp: rate limit synflood warnings further
MIPS: lantiq: dma: add dev pointer
netfilter: xt_hashlimit: use s->file instead of s->private
netfilter: nfnetlink_queue: Solve the NFQUEUE/conntrack clash for NF_REPEAT
netfilter: cttimeout: ctnl_timeout_find_get() returns incorrect pointer to type
netfilter: conntrack: timeout interface depend on CONFIG_NF_CONNTRACK_TIMEOUT
netfilter: conntrack: reset tcp maxwin on re-register
qmi_wwan: Support dynamic config on Quectel EP06
ethernet: renesas: convert to SPDX identifiers
...
dma_zalloc_coherent() now crashes if no dev pointer is given.
Add a dev pointer to the ltq_dma_channel structure and fill it in the
driver using it.
This fixes a bug introduced in kernel 4.19.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the devicetree nodes for the DMA core of the JZ4740 SoC, disabled
by default, as currently there are no clients for the DMA driver
(until the MMC driver and/or others get a devicetree node).
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Add the two devicetree nodes for the two DMA cores of the JZ4770 SoC,
disabled by default, as currently there are no clients for the DMA
driver (until the MMC driver and/or others get a devicetree node).
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The driver now accepts two memory resources, the first one for the
channel-specific registers, the second one for the controller-specific
registers.
Note that older devicetrees, without this commit, will still work with
the jz4780-dma driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Mathieu Malaterre <malat@debian.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
ARM:
- Fix a VFP corruption in 32-bit guest
- Add missing cache invalidation for CoW pages
- Two small cleanups
s390:
- Fallout from the hugetlbfs support: pfmf interpretion and locking
- VSIE: fix keywrapping for nested guests
PPC:
- Fix a bug where pages might not get marked dirty, causing
guest memory corruption on migration,
- Fix a bug causing reads from guest memory to use the wrong guest
real address for very large HPT guests (>256G of memory), leading to
failures in instruction emulation.
x86:
- Fix out of bound access from malicious pv ipi hypercalls (introduced
in rc1)
- Fix delivery of pending interrupts when entering a nested guest,
preventing arbitrarily late injection
- Sanitize kvm_stat output after destroying a guest
- Fix infinite loop when emulating a nested guest page fault
and improve the surrounding emulation code
- Two minor cleanups
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJbk5gAAAoJEED/6hsPKofoS0UH/1clCzg/8x3jhpDcKKp6tDm7
9XHOOQ6XmydT0HXYJNqZepGNqU99ip+2u4x8E9LCT5MTvTMZ1BcNM6PmenjJVULY
GMJtwZhjqoklrOcNkXGqIye4Ec+I0pBuMmt0AN0N85CcHO8VUBpMzsdxgJLuxcRm
UT6OZnCLyJsock6BqkZmqVsJj/gemFnI9MpudnrU8cCFk60roXmQWJ66fMIFfKjt
q0R61t8nmbapQKE8pjqBNgbCsuotVOtU1zgMkeM5LkaYEfc65ZPdgt3sdpyG8Guq
WA7Vt6HEvmNrcQxHFX5P0GxTVM9lOVCUx1bKXE4+57CMZOYl/8hDaTudlcacutg=
=FyuN
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- Fix a VFP corruption in 32-bit guest
- Add missing cache invalidation for CoW pages
- Two small cleanups
s390:
- Fallout from the hugetlbfs support: pfmf interpretion and locking
- VSIE: fix keywrapping for nested guests
PPC:
- Fix a bug where pages might not get marked dirty, causing guest
memory corruption on migration
- Fix a bug causing reads from guest memory to use the wrong guest
real address for very large HPT guests (>256G of memory), leading
to failures in instruction emulation.
x86:
- Fix out of bound access from malicious pv ipi hypercalls
(introduced in rc1)
- Fix delivery of pending interrupts when entering a nested guest,
preventing arbitrarily late injection
- Sanitize kvm_stat output after destroying a guest
- Fix infinite loop when emulating a nested guest page fault and
improve the surrounding emulation code
- Two minor cleanups"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (28 commits)
KVM: LAPIC: Fix pv ipis out-of-bounds access
KVM: nVMX: Fix loss of pending IRQ/NMI before entering L2
arm64: KVM: Remove pgd_lock
KVM: Remove obsolete kvm_unmap_hva notifier backend
arm64: KVM: Only force FPEXC32_EL2.EN if trapping FPSIMD
KVM: arm/arm64: Clean dcache to PoC when changing PTE due to CoW
KVM: s390: Properly lock mm context allow_gmap_hpage_1m setting
KVM: s390: vsie: copy wrapping keys to right place
KVM: s390: Fix pfmf and conditional skey emulation
tools/kvm_stat: re-animate display of dead guests
tools/kvm_stat: indicate dead guests as such
tools/kvm_stat: handle guest removals more gracefully
tools/kvm_stat: don't reset stats when setting PID filter for debugfs
tools/kvm_stat: fix updates for dead guests
tools/kvm_stat: fix handling of invalid paths in debugfs provider
tools/kvm_stat: fix python3 issues
KVM: x86: Unexport x86_emulate_instruction()
KVM: x86: Rename emulate_instruction() to kvm_emulate_instruction()
KVM: x86: Do not re-{try,execute} after failed emulation in L2
KVM: x86: Default to not allowing emulation retry in kvm_mmu_page_fault
...
The old rtc driver is getting in the way of some compat_ioctl
simplification. Looking up the loongson64 git history, it seems
that everyone uses the more modern but compatible RTC_CMOS driver
anyway, so let's remove the special case for loongson64.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
kvm_unmap_hva is long gone, and we only have kvm_unmap_hva_range to
deal with. Drop the now obsolete code.
Fixes: fb1522e099 ("KVM: update to new mmu_notifier semantic v2")
Cc: James Hogan <jhogan@kernel.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Set the PCI controller of_node such that PCI devices can be
instantiated via device tree.
Signed-off-by: Tobias Wolf <dev-NTEO@vplace.de>
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20423/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Enable the i2c controller on ocelot PCB123. While there are no i2c devices
on the board itself, it can be used to control the SFP transceivers.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20352/
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: linux-i2c@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Allan Nielsen <allan.nielsen@microchip.com>
Ocelot has an i2c controller, add it. There is only one possible pinmux
configuration so add it as well.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20353/
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: linux-i2c@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Allan Nielsen <allan.nielsen@microchip.com>
The comment describing arch_mem_init() was separated from the definition
of arch_mem_init() by commit a09fc446fb ("[MIPS] setup.c: use
early_param() for early command line parsing"). Move the comment such
that it's next to the definition again for ease of reading.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Clean up instances of casts to the type that a value already has, since
they are effectively no-ops and only serve to complicate the code.
This is the result of the following semantic patch:
@identitycast@
type T;
T *A;
@@
- (T *)(A)
+ A
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/19599/
When a system suffers from dcache aliasing a user program may observe
stale VDSO data from an aliased cache line. Notably this can break the
expectation that clock_gettime(CLOCK_MONOTONIC, ...) is, as its name
suggests, monotonic.
In order to ensure that users observe updates to the VDSO data page as
intended, align the user mappings of the VDSO data page such that their
cache colouring matches that of the virtual address range which the
kernel will use to update the data page - typically its unmapped address
within kseg0.
This ensures that we don't introduce aliasing cache lines for the VDSO
data page, and therefore that userland will observe updates without
requiring cache invalidation.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Hauke Mehrtens <hauke@hauke-m.de>
Reported-by: Rene Nielsen <rene.nielsen@microsemi.com>
Reported-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes: ebb5e78cc6 ("MIPS: Initial implementation of a VDSO")
Patchwork: https://patchwork.linux-mips.org/patch/20344/
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Tested-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # v4.4+
The rt3352 has a pin that can be used as second spi chip select,
watchdog reset or GPIO. The pinmux setup was missing the definition of
said pin.
The pin is configured via the same bit on rt5350, so reuse the existing
macro.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20301/
Cc: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
arch/mips appears to have inherited SLOW_DOWN_IO from arch/x86 in
antiquity, but we never define CONF_SLOWDOWN_IO so this is unused code.
Perhaps it was once useful to keep the MIPS header close to the x86
version to ease comparisons or porting changes, but they've diverged
significantly at this point & x86 does this differently now anyway.
Delete the dead code.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20343/
Cc: linux-mips@linux-mips.org
MIPS has a copy of lib/iomap.c with minor alterations, none of which are
necessary given appropriate definitions of PIO_OFFSET, PIO_MASK &
PIO_RESERVED. Provide such definitions, select GENERIC_IOMAP & remove
arch/mips/lib/iomap.c to cut back on the needless duplication.
The one change this does make is to our mmio_{in,out}s[bwl] functions,
which began to deviate from their generic counterparts with commit
0845bb721e ("MIPS: iomap: Use __mem_{read,write}{b,w,l} for MMIO"). I
suspect that this commit was incorrect, and that the SEAD-3 platform
should have instead selected CONFIG_SWAP_IO_SPACE. Since the SEAD-3
platform code is now gone & the board is instead supported by the
generic platform (CONFIG_MIPS_GENERIC) which selects
CONFIG_SWAP_IO_SPACE anyway, this shouldn't be a problem any more.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20342/
Cc: linux-mips@linux-mips.org
For a long time arch/mips/Makefile used nm to discover the kernel entry
point by looking for the address of the kernel_entry symbol. This
doesn't work for systems which make use of bit 0 of the PC to reflect
the ISA mode - ie. microMIPS (and MIPS16, but we don't support building
kernels that target MIPS16 anyway).
So for a while with commit 5fc9484f5e ("MIPS: Set ISA bit in entry-y
for microMIPS kernels") we manually modified the last nibble of the
output from nm, which worked but wasn't particularly pretty.
Commit 27c524d174 ("MIPS: Use the entry point from the ELF file
header") then cleaned this up by using objdump to print the ELF entry
point which includes the ISA bit, rather than using nm to print the
address of the kernel_entry symbol which doesn't. That removed the ugly
replacement of the last nibble, but added its own ugliness by needing to
manually sign extend in the 32 bit case.
Unfortunately it has been pointed out that objdump's output is
localised, and therefore grepping for its "start address" output doesn't
work when the user's language settings are such that objdump doesn't
print in English.
We could simply revert commit 27c524d174 ("MIPS: Use the entry point
from the ELF file header") and return to the manual replacement of the
last nibble of entry-y, but it seems that was found sufficiently
unpalatable to avoid. We could attempt to force the language used by
objdump by setting an environment variable such as LC_ALL, but that
seems fragile. Instead we add a small tool named elf-entry which simply
prints out the entry point of the kernel in the format we require.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Philippe Reynes <philippe.reynes@softathome.com>
Tested-by: Philippe Reynes <philippe.reynes@softathome.com>
Fixes: 27c524d174 ("MIPS: Use the entry point from the ELF file header")
Patchwork: https://patchwork.linux-mips.org/patch/20322/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Setting GPIO 21 high seems to be required to enable power to USB ports
on the WNDR3400v3. As there is already similar code for WNR3500L,
make the existing USB power GPIO code generic and use that.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20259/
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
After changing over to 64-bit time_t syscalls, many architectures will
want compat_sys_utimensat() but not respective handlers for utime(),
utimes() and futimesat(). This adds a new __ARCH_WANT_SYS_UTIME32 to
complement __ARCH_WANT_SYS_UTIME. For now, all 64-bit architectures that
support CONFIG_COMPAT set it, but future 64-bit architectures will not
(tile would not have needed it either, but got removed).
As older 32-bit architectures get converted to using CONFIG_64BIT_TIME,
they will have to use __ARCH_WANT_SYS_UTIME32 instead of
__ARCH_WANT_SYS_UTIME. Architectures using the generic syscall ABI don't
need either of them as they never had a utime syscall.
Since the compat_utimbuf structure is now required outside of
CONFIG_COMPAT, I'm moving it into compat_time.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
---
changed from last version:
- renamed __ARCH_WANT_COMPAT_SYS_UTIME to __ARCH_WANT_SYS_UTIME32
The sys_llseek sytem call is needed on all 32-bit architectures and
none of the 64-bit ones, so we can remove the __ARCH_WANT_SYS_LLSEEK guard
and simplify the include/asm-generic/unistd.h header further.
Since 32-bit tasks can run either natively or in compat mode on 64-bit
architectures, we have to check for both !CONFIG_64BIT and CONFIG_COMPAT.
There are a few 64-bit architectures that also reference sys_llseek
in their 64-bit ABI (e.g. sparc), but I verified that those all
select CONFIG_COMPAT, so the #if check is still correct here. It's
a bit odd to include it in the syscall table though, as it's the
same as sys_lseek() on 64-bit, but with strange calling conventions.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
While converting compat system call handlers to work on 32-bit
architectures, I found a number of types used in those handlers
that are identical between all architectures.
Let's move all the identical ones into asm-generic/compat.h to avoid
having to add even more identical definitions of those types.
For unknown reasons, mips defines __compat_gid32_t, __compat_uid32_t
and compat_caddr_t as signed, while all others have them unsigned.
This seems to be a mistake, but I'm leaving it alone here. The other
types all differ by size or alignment on at least on architecture.
compat_aio_context_t is currently defined in linux/compat.h but
also needed for compat_sys_io_getevents(), so let's move it into
the same place.
While we still have not decided whether the 32-bit time handling
will always use the compat syscalls, or in which form, I think this
is a useful cleanup that we can merge regardless.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We have four generations of stat() syscalls:
- the oldstat syscalls that are only used on the older architectures
- the newstat family that is used on all 64-bit architectures but
lacked support for large files on 32-bit architectures.
- the stat64 family that is used mostly on 32-bit architectures to
replace newstat
- statx() to replace all of the above, adding 64-bit timestamps among
other things.
We already compile stat64 only on those architectures that need it,
but newstat is always built, including on those that don't reference
it. This adds a new __ARCH_WANT_NEW_STAT symbol along the lines of
__ARCH_WANT_OLD_STAT and __ARCH_WANT_STAT64 to control compilation of
newstat. All architectures that need it use an explict define, the
others now get a little bit smaller, and future architecture (including
64-bit targets) won't ever see it.
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20315/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: John Crispin <john@phrozen.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Split the common dma.c which shared by Loongson-2E and Loongson-2F,
since the code in 'common' directory is assumed be shared by all 64bit
Loongson platforms (but Loongson-3 doesn't use it now). By the way,
Loongson-2E and Loongson-2F have already dropped 32bit kernel support,
so CONFIG_64BIT isn't needed.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20302/
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Huacai Chen <chenhuacai@gmail.com>
Christoph Hellwig suggested a slightly different path for handling
backwards compatibility with the 32-bit time_t based system calls:
Rather than simply reusing the compat_sys_* entry points on 32-bit
architectures unchanged, we get rid of those entry points and the
compat_time types by renaming them to something that makes more sense
on 32-bit architectures (which don't have a compat mode otherwise),
and then share the entry points under the new name with the 64-bit
architectures that use them for implementing the compatibility.
The following types and interfaces are renamed here, and moved
from linux/compat_time.h to linux/time32.h:
old new
--- ---
compat_time_t old_time32_t
struct compat_timeval struct old_timeval32
struct compat_timespec struct old_timespec32
struct compat_itimerspec struct old_itimerspec32
ns_to_compat_timeval() ns_to_old_timeval32()
get_compat_itimerspec64() get_old_itimerspec32()
put_compat_itimerspec64() put_old_itimerspec32()
compat_get_timespec64() get_old_timespec32()
compat_put_timespec64() put_old_timespec32()
As we already have aliases in place, this patch addresses only the
instances that are relevant to the system call interface in particular,
not those that occur in device drivers and other modules. Those
will get handled separately, while providing the 64-bit version
of the respective interfaces.
I'm not renaming the timex, rusage and itimerval structures, as we are
still debating what the new interface will look like, and whether we
will need a replacement at all.
This also doesn't change the names of the syscall entry points, which can
be done more easily when we actually switch over the 32-bit architectures
to use them, at that point we need to change COMPAT_SYSCALL_DEFINEx to
SYSCALL_DEFINEx with a new name, e.g. with a _time32 suffix.
Suggested-by: Christoph Hellwig <hch@infradead.org>
Link: https://lore.kernel.org/lkml/20180705222110.GA5698@infradead.org/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- add build_{menu,n,g,x}config targets for compile-testing Kconfig
- fix and improve recursive dependency detection in Kconfig
- fix parallel building of menuconfig/nconfig
- fix syntax error in clang-version.sh
- suppress distracting log from syncconfig
- remove obsolete "rpm" target
- remove VMLINUX_SYMBOL(_STR) macro entirely
- fix microblaze build with CONFIG_DYNAMIC_FTRACE
- move compiler test for dead code/data elimination to Kconfig
- rename well-known LDFLAGS variable to KBUILD_LDFLAGS
- misc fixes and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Vsb2
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- add build_{menu,n,g,x}config targets for compile-testing Kconfig
- fix and improve recursive dependency detection in Kconfig
- fix parallel building of menuconfig/nconfig
- fix syntax error in clang-version.sh
- suppress distracting log from syncconfig
- remove obsolete "rpm" target
- remove VMLINUX_SYMBOL(_STR) macro entirely
- fix microblaze build with CONFIG_DYNAMIC_FTRACE
- move compiler test for dead code/data elimination to Kconfig
- rename well-known LDFLAGS variable to KBUILD_LDFLAGS
- misc fixes and cleanups
* tag 'kbuild-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kbuild: rename LDFLAGS to KBUILD_LDFLAGS
kbuild: pass LDFLAGS to recordmcount.pl
kbuild: test dead code/data elimination support in Kconfig
initramfs: move gen_initramfs_list.sh from scripts/ to usr/
vmlinux.lds.h: remove stale <linux/export.h> include
export.h: remove VMLINUX_SYMBOL() and VMLINUX_SYMBOL_STR()
Coccinelle: remove pci_alloc_consistent semantic to detect in zalloc-simple.cocci
kbuild: make sorting initramfs contents independent of locale
kbuild: remove "rpm" target, which is alias of "rpm-pkg"
kbuild: Fix LOADLIBES rename in Documentation/kbuild/makefiles.txt
kconfig: suppress "configuration written to .config" for syncconfig
kconfig: fix "Can't open ..." in parallel build
kbuild: Add a space after `!` to prevent parsing as file pattern
scripts: modpost: check memory allocation results
kconfig: improve the recursive dependency report
kconfig: report recursive dependency involving 'imply'
kconfig: error out when seeing recursive dependency
kconfig: add build-only configurator targets
scripts/dtc: consolidate include path options in Makefile
Commit a0f97e06a4 ("kbuild: enable 'make CFLAGS=...' to add
additional options to CC") renamed CFLAGS to KBUILD_CFLAGS.
Commit 222d394d30 ("kbuild: enable 'make AFLAGS=...' to add
additional options to AS") renamed AFLAGS to KBUILD_AFLAGS.
Commit 06c5040cdb ("kbuild: enable 'make CPPFLAGS=...' to add
additional options to CPP") renamed CPPFLAGS to KBUILD_CPPFLAGS.
For some reason, LDFLAGS was not renamed.
Using a well-known variable like LDFLAGS may result in accidental
override of the variable.
Kbuild generally uses KBUILD_ prefixed variables for the internally
appended options, so here is one more conversion to sanitize the
naming convention.
I did not touch Makefiles under tools/ since the tools build system
is a different world.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
- Fix microMIPS build failures by adding a .insn directive to the
barrier_before_unreachable() asm statement in order to convince the
toolchain that the asm statement is a valid branch target rather
than a bogus attempt to switch ISA.
- Clean up our declarations of TLB functions that we overwrite with
generated code in order to prevent the compiler making assumptions
about alignment that cause microMIPS kernels built with GCC 7 &
above to die early during boot.
- Fix up a regression for MIPS32 kernels which slipped into the main
MIPS pull for 4.19, causing CONFIG_32BIT=y kernels to contain
inappropriate MIPS64 instructions.
- Extend our existing workaround for MIPSr6 builds that end up using
the __multi3 intrinsic to GCC 7 & below, rather than just GCC 7.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCW37wVhUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN18iAD/ZO02rgkTgMG7NvZMtbOwflxe1aVz
YpAQzcOSz+CBxgUA/30ZwZm37hgMi3YWOJMSfmbuWKsYi+/vkcjwlfai7UUF
=oJFy
-----END PGP SIGNATURE-----
Merge tag 'mips_4.19_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
- Fix microMIPS build failures by adding a .insn directive to the
barrier_before_unreachable() asm statement in order to convince the
toolchain that the asm statement is a valid branch target rather
than a bogus attempt to switch ISA.
- Clean up our declarations of TLB functions that we overwrite with
generated code in order to prevent the compiler making assumptions
about alignment that cause microMIPS kernels built with GCC 7 &
above to die early during boot.
- Fix up a regression for MIPS32 kernels which slipped into the main
MIPS pull for 4.19, causing CONFIG_32BIT=y kernels to contain
inappropriate MIPS64 instructions.
- Extend our existing workaround for MIPSr6 builds that end up using
the __multi3 intrinsic to GCC 7 & below, rather than just GCC 7.
* tag 'mips_4.19_2' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: lib: Provide MIPS64r6 __multi3() for GCC < 7
MIPS: Workaround GCC __builtin_unreachable reordering bug
compiler.h: Allow arch-specific asm/compiler.h
MIPS: Avoid move psuedo-instruction whilst using MIPS_ISA_LEVEL
MIPS: Consistently declare TLB functions
MIPS: Export tlbmiss_handler_setup_pgd near its definition
Some versions of GCC suboptimally generate calls to the __multi3()
intrinsic for MIPS64r6 builds, resulting in link failures due to the
missing function:
LD vmlinux.o
MODPOST vmlinux.o
kernel/bpf/verifier.o: In function `kmalloc_array':
include/linux/slab.h:631: undefined reference to `__multi3'
fs/select.o: In function `kmalloc_array':
include/linux/slab.h:631: undefined reference to `__multi3'
...
We already have a workaround for this in which we provide the
instrinsic, but we do so selectively for GCC 7 only. Unfortunately the
issue occurs with older GCC versions too - it has been observed with
both GCC 5.4.0 & GCC 6.4.0.
MIPSr6 support was introduced in GCC 5, so all major GCC versions prior
to GCC 8 are affected and we extend our workaround accordingly to all
MIPS64r6 builds using GCC versions older than GCC 8.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Reported-by: Vladimir Kondratiev <vladimir.kondratiev@intel.com>
Fixes: ebabcf17bc ("MIPS: Implement __multi3 for GCC7 MIPS64r6 builds")
Patchwork: https://patchwork.linux-mips.org/patch/20297/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 4.15+
Some versions of GCC for the MIPS architecture suffer from a bug which
can lead to instructions from beyond an unreachable statement being
incorrectly reordered into earlier branch delay slots if the unreachable
statement is the only content of a case in a switch statement. This can
lead to seemingly random behaviour, such as invalid memory accesses from
incorrectly reordered loads or stores, and link failures on microMIPS
builds.
See this potential GCC fix for details:
https://gcc.gnu.org/ml/gcc-patches/2015-09/msg00360.html
Runtime problems resulting from this bug were initially observed using a
maltasmvp_defconfig v4.4 kernel built using GCC 4.9.2 (from a Codescape
SDK 2015.06-05 toolchain), with the result being an address exception
taken after log messages about the L1 caches (during probe of the L2
cache):
Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff]
VPE topology {2,2} total 4
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 64kB, 4-way, PIPT, no aliases, linesize 32 bytes
<AdEL exception here>
This is early enough that the kernel exception vectors are not in use,
so any further output depends upon the bootloader. This is reproducible
in QEMU where no further output occurs - ie. the system hangs here.
Given the nature of the bug it may potentially be hit with differing
symptoms. The bug is known to affect GCC versions as recent as 7.3, and
it is unclear whether GCC 8 fixed it or just happens not to encounter
the bug in the testcase found at the link above due to differing
optimizations.
This bug can be worked around by placing a volatile asm statement, which
GCC is prevented from reordering past, prior to the
__builtin_unreachable call.
That was actually done already for other reasons by commit 173a3efd3e
("bug.h: work around GCC PR82365 in BUG()"), but creates problems for
microMIPS builds due to the lack of a .insn directive. The microMIPS ISA
allows for interlinking with regular MIPS32 code by repurposing bit 0 of
the program counter as an ISA mode bit. To switch modes one changes the
value of this bit in the PC. However typical branch instructions encode
their offsets as multiples of 2-byte instruction halfwords, which means
they cannot change ISA mode - this must be done using either an indirect
branch (a jump-register in MIPS terminology) or a dedicated jalx
instruction. In order to ensure that regular branches don't attempt to
target code in a different ISA which they can't actually switch to, the
linker will check that branch targets are code in the same ISA as the
branch.
Unfortunately our empty asm volatile statements don't qualify as code,
and the link for microMIPS builds fails with errors such as:
arch/mips/mm/dma-default.s:3265: Error: branch to a symbol in another ISA mode
arch/mips/mm/dma-default.s:5027: Error: branch to a symbol in another ISA mode
Resolve this by adding a .insn directive within the asm statement which
declares that what comes next is code. This may or may not be true,
since we don't really know what comes next, but as this code is in an
unreachable path anyway that doesn't matter since we won't execute it.
We do this in asm/compiler.h & select CONFIG_HAVE_ARCH_COMPILER_H in
order to have this included by linux/compiler_types.h after
linux/compiler-gcc.h. This will result in asm/compiler.h being included
in all C compilations via the -include linux/compiler_types.h argument
in c_flags, which should be harmless.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 173a3efd3e ("bug.h: work around GCC PR82365 in BUG()")
Patchwork: https://patchwork.linux-mips.org/patch/20270/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-mips@linux-mips.org
- Restructure of lockdep and latency tracers
This is the biggest change. Joel Fernandes restructured the hooks
from irqs and preemption disabling and enabling. He got rid of
a lot of the preprocessor #ifdef mess that they caused.
He turned both lockdep and the latency tracers to use trace events
inserted in the preempt/irqs disabling paths. But unfortunately,
these started to cause issues in corner cases. Thus, parts of the
code was reverted back to where lockde and the latency tracers
just get called directly (without using the trace events).
But because the original change cleaned up the code very nicely
we kept that, as well as the trace events for preempt and irqs
disabling, but they are limited to not being called in NMIs.
- Have trace events use SRCU for "rcu idle" calls. This was required
for the preempt/irqs off trace events. But it also had to not
allow them to be called in NMI context. Waiting till Paul makes
an NMI safe SRCU API.
- New notrace SRCU API to allow trace events to use SRCU.
- Addition of mcount-nop option support
- SPDX headers replacing GPL templates.
- Various other fixes and clean ups.
- Some fixes are marked for stable, but were not fully tested
before the merge window opened.
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCW3ruhRQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qiM7AP47NhYdSnCFCRUJfrt6PovXmQtuCHt3
c3QMoGGdvzh9YAEAqcSXwh7uLhpHUp1LjMAPkXdZVwNddf4zJQ1zyxQ+EAU=
=vgEr
-----END PGP SIGNATURE-----
Merge tag 'trace-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
- Restructure of lockdep and latency tracers
This is the biggest change. Joel Fernandes restructured the hooks
from irqs and preemption disabling and enabling. He got rid of a lot
of the preprocessor #ifdef mess that they caused.
He turned both lockdep and the latency tracers to use trace events
inserted in the preempt/irqs disabling paths. But unfortunately,
these started to cause issues in corner cases. Thus, parts of the
code was reverted back to where lockdep and the latency tracers just
get called directly (without using the trace events). But because the
original change cleaned up the code very nicely we kept that, as well
as the trace events for preempt and irqs disabling, but they are
limited to not being called in NMIs.
- Have trace events use SRCU for "rcu idle" calls. This was required
for the preempt/irqs off trace events. But it also had to not allow
them to be called in NMI context. Waiting till Paul makes an NMI safe
SRCU API.
- New notrace SRCU API to allow trace events to use SRCU.
- Addition of mcount-nop option support
- SPDX headers replacing GPL templates.
- Various other fixes and clean ups.
- Some fixes are marked for stable, but were not fully tested before
the merge window opened.
* tag 'trace-v4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (44 commits)
tracing: Fix SPDX format headers to use C++ style comments
tracing: Add SPDX License format tags to tracing files
tracing: Add SPDX License format to bpf_trace.c
blktrace: Add SPDX License format header
s390/ftrace: Add -mfentry and -mnop-mcount support
tracing: Add -mcount-nop option support
tracing: Avoid calling cc-option -mrecord-mcount for every Makefile
tracing: Handle CC_FLAGS_FTRACE more accurately
Uprobe: Additional argument arch_uprobe to uprobe_write_opcode()
Uprobes: Simplify uprobe_register() body
tracepoints: Free early tracepoints after RCU is initialized
uprobes: Use synchronize_rcu() not synchronize_sched()
tracing: Fix synchronizing to event changes with tracepoint_synchronize_unregister()
ftrace: Remove unused pointer ftrace_swapper_pid
tracing: More reverting of "tracing: Centralize preemptirq tracepoints and unify their usage"
tracing/irqsoff: Handle preempt_count for different configs
tracing: Partial revert of "tracing: Centralize preemptirq tracepoints and unify their usage"
tracing: irqsoff: Account for additional preempt_disable
trace: Use rcu_dereference_raw for hooks from trace-event subsystem
tracing/kprobes: Fix within_notrace_func() to check only notrace functions
...
MIPS_ISA_LEVEL is always defined as the 64 bit ISA that is a compatible
superset of the ISA that the kernel build is targeting, and is used to
allow us to emit instructions that we may detect support for at runtime.
When we use a .set MIPS_ISA_LEVEL directive & are building a 32-bit
kernel, we therefore are temporarily allowing the assembler to generate
MIPS64 instructions. Using the move pseudo-instruction whilst this is
the case is problematic because the assembler is likely to emit a daddu
instruction which will generate a reserved instruction exception when
executed on a MIPS32 machine.
Unfortunately the combination of commit a0a5ac3ce8 ("MIPS: Fix delay
slot bug in `atomic*_sub_if_positive' for R10000_LLSC_WAR") and commit
4936084c2e ("MIPS: Cleanup R10000_LLSC_WAR logic in atomic.h") causes
us to do exactly this in atomic_sub_if_positive(), and the result is
MIPS64 daddu instructions in 32-bit kernels.
Fix this by using .set mips0 to restore the default ISA after the ll
instruction, and use .set MIPS_ISA_LEVEL again prior to the sc. This
ensures everything but the ll & sc are assembled using the default ISA
for the kernel build & the move pseudo-instruction is emitted as a
MIPS32 addu instruction.
We appear to have another pre-existing instance of the same issue in our
atomic_fetch_*_relaxed() functions, and fix that up too by moving our
.set move0 such that it occurs prior to use of the move
pseudo-instruction.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: a0a5ac3ce8 ("MIPS: Fix delay slot bug in `atomic*_sub_if_positive' for R10000_LLSC_WAR")
Fixes: 4936084c2e ("MIPS: Cleanup R10000_LLSC_WAR logic in atomic.h")
Patchwork: https://patchwork.linux-mips.org/patch/20253/
Cc: James Hogan <jhogan@kernel.org>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
Use new return type vm_fault_t for fault handler. For now, this is just
documenting that the function returns a VM_FAULT value rather than an
errno. Once all instances are converted, vm_fault_t will become a
distinct type.
Ref-> commit 1c8f422059 ("mm: change return type to vm_fault_t")
In this patch all the caller of handle_mm_fault() are changed to return
vm_fault_t type.
Link: http://lkml.kernel.org/r/20180617084810.GA6730@jordon-HP-15-Notebook-PC
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: James Hogan <jhogan@kernel.org>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: David S. Miller <davem@davemloft.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Levin, Alexander (Sasha Levin)" <alexander.levin@verizon.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking updates from David Miller:
"Highlights:
- Gustavo A. R. Silva keeps working on the implicit switch fallthru
changes.
- Support 802.11ax High-Efficiency wireless in cfg80211 et al, From
Luca Coelho.
- Re-enable ASPM in r8169, from Kai-Heng Feng.
- Add virtual XFRM interfaces, which avoids all of the limitations of
existing IPSEC tunnels. From Steffen Klassert.
- Convert GRO over to use a hash table, so that when we have many
flows active we don't traverse a long list during accumluation.
- Many new self tests for routing, TC, tunnels, etc. Too many
contributors to mention them all, but I'm really happy to keep
seeing this stuff.
- Hardware timestamping support for dpaa_eth/fsl-fman from Yangbo Lu.
- Lots of cleanups and fixes in L2TP code from Guillaume Nault.
- Add IPSEC offload support to netdevsim, from Shannon Nelson.
- Add support for slotting with non-uniform distribution to netem
packet scheduler, from Yousuk Seung.
- Add UDP GSO support to mlx5e, from Boris Pismenny.
- Support offloading of Team LAG in NFP, from John Hurley.
- Allow to configure TX queue selection based upon RX queue, from
Amritha Nambiar.
- Support ethtool ring size configuration in aquantia, from Anton
Mikaev.
- Support DSCP and flowlabel per-transport in SCTP, from Xin Long.
- Support list based batching and stack traversal of SKBs, this is
very exciting work. From Edward Cree.
- Busyloop optimizations in vhost_net, from Toshiaki Makita.
- Introduce the ETF qdisc, which allows time based transmissions. IGB
can offload this in hardware. From Vinicius Costa Gomes.
- Add parameter support to devlink, from Moshe Shemesh.
- Several multiplication and division optimizations for BPF JIT in
nfp driver, from Jiong Wang.
- Lots of prepatory work to make more of the packet scheduler layer
lockless, when possible, from Vlad Buslov.
- Add ACK filter and NAT awareness to sch_cake packet scheduler, from
Toke Høiland-Jørgensen.
- Support regions and region snapshots in devlink, from Alex Vesker.
- Allow to attach XDP programs to both HW and SW at the same time on
a given device, with initial support in nfp. From Jakub Kicinski.
- Add TLS RX offload and support in mlx5, from Ilya Lesokhin.
- Use PHYLIB in r8169 driver, from Heiner Kallweit.
- All sorts of changes to support Spectrum 2 in mlxsw driver, from
Ido Schimmel.
- PTP support in mv88e6xxx DSA driver, from Andrew Lunn.
- Make TCP_USER_TIMEOUT socket option more accurate, from Jon
Maxwell.
- Support for templates in packet scheduler classifier, from Jiri
Pirko.
- IPV6 support in RDS, from Ka-Cheong Poon.
- Native tproxy support in nf_tables, from Máté Eckl.
- Maintain IP fragment queue in an rbtree, but optimize properly for
in-order frags. From Peter Oskolkov.
- Improvde handling of ACKs on hole repairs, from Yuchung Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1996 commits)
bpf: test: fix spelling mistake "REUSEEPORT" -> "REUSEPORT"
hv/netvsc: Fix NULL dereference at single queue mode fallback
net: filter: mark expected switch fall-through
xen-netfront: fix warn message as irq device name has '/'
cxgb4: Add new T5 PCI device ids 0x50af and 0x50b0
net: dsa: mv88e6xxx: missing unlock on error path
rds: fix building with IPV6=m
inet/connection_sock: prefer _THIS_IP_ to current_text_addr
net: dsa: mv88e6xxx: bitwise vs logical bug
net: sock_diag: Fix spectre v1 gadget in __sock_diag_cmd()
ieee802154: hwsim: using right kind of iteration
net: hns3: Add vlan filter setting by ethtool command -K
net: hns3: Set tx ring' tc info when netdev is up
net: hns3: Remove tx ring BD len register in hns3_enet
net: hns3: Fix desc num set to default when setting channel
net: hns3: Fix for phy link issue when using marvell phy driver
net: hns3: Fix for information of phydev lost problem when down/up
net: hns3: Fix for command format parsing error in hclge_is_all_function_id_zero
net: hns3: Add support for serdes loopback selftest
bnxt_en: take coredump_record structure off stack
...
Move the source statements of arch-independent Kconfig files instead of
duplicating the includes in every arch/$(SRCARCH)/Kconfig.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gsQJ
-----END PGP SIGNATURE-----
Merge tag 'kconfig-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig consolidation from Masahiro Yamada:
"Consolidation of Kconfig files by Christoph Hellwig.
Move the source statements of arch-independent Kconfig files instead
of duplicating the includes in every arch/$(SRCARCH)/Kconfig"
* tag 'kconfig-v4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: add a Memory Management options" menu
kconfig: move the "Executable file formats" menu to fs/Kconfig.binfmt
kconfig: use a menu in arch/Kconfig to reduce clutter
kconfig: include kernel/Kconfig.preempt from init/Kconfig
Kconfig: consolidate the "Kernel hacking" menu
kconfig: include common Kconfig files from top-level Kconfig
kconfig: remove duplicate SWAP symbol defintions
um: create a proper drivers Kconfig
um: cleanup Kconfig files
um: stop abusing KBUILD_KCONFIG
- Support 64-bit timestamps
MTD changes:
Core changes:
- Support sub-partitions
- Clarify mtd_oob_ops documentation
- Make Kconfig formatting consistent
- Fix potential overflows in mtdchar_{write,read}()
- Fallback to ->_{read,write}() when ->_{read,write}_oob() is missing
and no OOB data were requested
- Remove VLA usage in the bch lib
Driver changes:
- Use mtd_device_register() instead of mtd_device_parse_register()
where applicable
- Use proper printk format to print physical addresses in the
solutionengine driver
- Add missing mtd_set_of_node() call in the powernv driver
- Remove unneeded variables in a few drivers
- Plug the TRX part parser to the DT partition parsers logic
- Check ioremap_cache() return code in the gpio-addr-flash driver
- Stop using VMLINUX_SYMBOL_STR() in gen_probe.c
SPI NOR changes:
Core changes:
- Apply reset hacks only when reset is explicitly marked as broken in
the DT
Driver changes:
- Minor cleanup/fixes in the m25p80 driver
- Release flash_np in the nxp-spifi driver
- Add suspend/resume hooks to the atmel-quadspi driver
- Include gpio/consumer.h instead of gpio.h in the atmel-quadspi
driver
- Use %pK instead of %p in the stm32-quadspi driver
- Improve timeout handling in the cadence-quadspi driver
- Use mtd_device_register() instead of mtd_device_parse_register()
in the intel-spi driver
NAND changes:
Core changes:
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op().
-----BEGIN PGP SIGNATURE-----
iQI5BAABCAAjBQJbcSYdHBxib3Jpcy5icmV6aWxsb25AYm9vdGxpbi5jb20ACgkQ
Ze02AX4ItwA85Q//ViUNiWoluaj7q3Kpv44NZZClPjVfirDtIHEfyzob7HbkrqjT
ivjNUu5cjKU2aqptR24UzIV2lwmaSGicIzvyANN5bNedHy8tb4BWXo1iTEflXc1P
lYihrRz7AeHQqdrOYAiHxq0fcqgIm2NjCDxfdtkP1HJsMQH+LgvoosOkd8RyLF8E
jV5IyreTfg10AiVS44yvnqdsYo7GDVZRgnx1dBRbdJ+WwZS05m6LSeNu0ivgfLMM
NmISrn7pzlMYnuDkzckXwVka7STFhV9befoSCmAHedqNEHtzaGDaNMLEilaC4WzV
1yvsdRGI3hDkdO4s44nP/Vs2XlVmCevuTpOOQ1dEK94Bbek+us7NEPjxOIAf22jE
5MVZR6vpNN7JXJ+nvEZjjL8X9zysqZgk2r6os35Wi2zJK7iHIrFpjlMYwTJfVPzv
JKabOQZuOUqRACbL0isTTdG0+Tzr1BxaQqFiFUteQ9QpG4nSifoHUmI+9XUCJmil
iGTOy6rEkaMd6qu3xapPtZbxGbUbvcLiJvNrZ02ZfsELDAELowz66O0PX6rSwTV9
NIWeVNXK9Bsp0oxbb8P8oJIB5K4F6vqncPBls34J7E/xrLO9nLk1VvFQrGqzuwwP
HmEdgcRwKeXrvJITZz2u0u6lrKpgdDA3FTqfGCNec51PCgb1FwxcpKF/Xz0=
=yIkF
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-4.19' of git://git.infradead.org/linux-mtd
Pull mtd updates from Boris Brezillon:
"JFFS2 changes:
- Support 64-bit timestamps
MTD core changes:
- Support sub-partitions
- Clarify mtd_oob_ops documentation
- Make Kconfig formatting consistent
- Fix potential overflows in mtdchar_{write,read}()
- Fallback to ->_{read,write}() when ->_{read,write}_oob() is missing
and no OOB data were requested
- Remove VLA usage in the bch lib
MTD driver changes:
- Use mtd_device_register() instead of mtd_device_parse_register()
where applicable
- Use proper printk format to print physical addresses in the
solutionengine driver
- Add missing mtd_set_of_node() call in the powernv driver
- Remove unneeded variables in a few drivers
- Plug the TRX part parser to the DT partition parsers logic
- Check ioremap_cache() return code in the gpio-addr-flash driver
- Stop using VMLINUX_SYMBOL_STR() in gen_probe.c
SPI NOR core changes:
- Apply reset hacks only when reset is explicitly marked as broken in
the DT
SPI NOR driver changes:
- Minor cleanup/fixes in the m25p80 driver
- Release flash_np in the nxp-spifi driver
- Add suspend/resume hooks to the atmel-quadspi driver
- Include gpio/consumer.h instead of gpio.h in the atmel-quadspi
driver
- Use %pK instead of %p in the stm32-quadspi driver
- Improve timeout handling in the cadence-quadspi driver
- Use mtd_device_register() instead of mtd_device_parse_register() in
the intel-spi driver
NAND core changes:
- Add the SPI-NAND framework.
- Create a helper to find the best ECC configuration.
- Create NAND controller operations.
- Allocate dynamically ONFI parameters structure.
- Add defines for ONFI version bits.
- Add manufacturer fixup for ONFI parameter page.
- Add an option to specify NAND chip as a boot device.
- Add Reed-Solomon error correction algorithm.
- Better name for the controller structure.
- Remove unused caller_is_module() definition.
- Make subop helpers return unsigned values.
- Expose _notsupp() helpers for raw page accessors.
- Add default values for dynamic timings.
- Kill the chip->scan_bbt() hook.
- Rename nand_default_bbt() into nand_create_bbt().
- Start to clean the nand_chip structure.
- Remove stale prototype from rawnand.h.
Raw NAND controllers drivers changes:
- Qcom: structuring cleanup.
- Denali: use core helper to find the best ECC configuration.
- Possible build of almost all drivers by adding a dependency on
COMPILE_TEST for almost all of them in Kconfig, implies various
fixes, Kconfig cleanup, GPIO headers inclusion cleanup, and even
changes in sparc64 and ia64 architectures.
- Clean the ->probe() functions error path of a lot of drivers.
- Migrate all drivers to use nand_scan() instead of
nand_scan_ident()/nand_scan_tail() pair.
- Use mtd_device_register() where applicable to simplify the code.
- Marvell:
* Handle on-die ECC.
* Better clocks handling.
* Remove bogus comment.
* Add suspend and resume support.
- Tegra: add NAND controller driver.
- Atmel:
* Add module param to avoid using dma.
* Drop Wenyou Yang from MAINTAINERS.
- Denali: optimize timings handling.
- FSMC: Stop using chip->read_buf().
- FSL:
* Switch to SPDX license tag identifiers.
* Fix qualifiers in MXC init functions.
Raw NAND chip drivers changes:
- Micron:
* Add fixup for ONFI revision.
* Update ecc_stats.corrected.
* Make ECC activation stateful.
* Avoid enabling/disabling ECC when it can't be disabled.
* Get the actual number of bitflips.
* Allow forced on-die ECC.
* Support 8/512 on-die ECC.
* Fix on-die ECC detection logic.
- Hynix:
* Fix decoding the OOB size on H27UCG8T2BTR.
* Use ->exec_op() in hynix_nand_reg_write_op()"
* tag 'mtd/for-4.19' of git://git.infradead.org/linux-mtd: (188 commits)
mtd: rawnand: atmel: Select GENERIC_ALLOCATOR
MAINTAINERS: drop Wenyou Yang from Atmel NAND driver support
mtd: rawnand: allocate dynamically ONFI parameters during detection
mtd: spi-nor: only apply reset hacks to broken hardware
mtd: spi-nor: cadence-quadspi: fix timeout handling
mtd: spi-nor: atmel-quadspi: Include gpio/consumer.h instead of gpio.h
mtd: spi-nor: intel-spi: use mtd_device_register()
mtd: spi-nor: stm32-quadspi: replace "%p" with "%pK"
mtd: spi-nor: atmel-quadspi: add suspend/resume hooks
mtd: rawnand: allocate model parameter dynamically
mtd: rawnand: do not export nand_scan_[ident|tail]() anymore
mtd: rawnand: txx9ndfmc: convert driver to nand_scan()
mtd: rawnand: txx9ndfmc: clarify ECC parameters assignation
mtd: rawnand: tegra: convert driver to nand_scan()
mtd: rawnand: jz4740: convert driver to nand_scan()
mtd: rawnand: jz4740: group nand_scan_{ident, tail} calls
mtd: rawnand: jz4740: fix probe function error path
mtd: rawnand: docg4: convert driver to nand_scan()
mtd: rawnand: do not execute nand_scan_ident() if maxchips is zero
mtd: rawnand: atmel: convert driver to nand_scan()
...
An overview of the general architecture changes:
- Massive DMA ops refactoring from Christoph Hellwig (huzzah for
deleting crufty code!).
- We introduce NT_MIPS_DSP & NT_MIPS_FP_MODE ELF notes & corresponding
regsets to expose DSP ASE & floating point mode state respectively,
both for live debugging & core dumps.
- We better optimize our code by hard-coding cpu_has_* macros at
compile time where their values are known due to the ISA revision
that the kernel build is targeting.
- The EJTAG exception handler now better handles SMP systems, where it
was previously possible for CPUs to clobber a register value saved
by another CPU.
- Our implementation of memset() gained a couple of fixes for MIPSr6
systems to return correct values in some cases where stores fault.
- We now implement ioremap_wc() using the uncached-accelerated cache
coherency attribute where supported, which is detected during boot,
and fall back to plain uncached access where necessary. The
MIPS-specific (and unused in tree) ioremap_uncached_accelerated() &
ioremap_cacheable_cow() are removed.
- The prctl(PR_SET_FP_MODE, ...) syscall is better supported for SMP
systems by reworking the way we ensure remote CPUs that may be
running threads within the affected process switch mode.
- Systems using the MIPS Coherence Manager will now set the
MIPS_IC_SNOOPS_REMOTE flag to avoid some unnecessary cache
maintenance overhead when flushing the icache.
- A few fixes were made for building with clang/LLVM, which
now sucessfully builds kernels for many of our platforms.
- Miscellaneous cleanups all over.
And some platform-specific changes:
- ar7 gained stubs for a few clock API functions to fix build failures
for some drivers.
- ath79 gained support for a few new SoCs, a few fixes & better
gpio-keys support.
- Ci20 now exposes its SPI bus using the spi-gpio driver.
- The generic platform can now auto-detect a suitable value for
PHYS_OFFSET based upon the memory map described by the device tree,
allowing us to avoid wasting memory on page book-keeping for systems
where RAM starts at a non-zero physical address.
- Ingenic systems using the jz4740 platform code now link their
vmlinuz higher to allow for kernels of a realistic size.
- Loongson32 now builds the kernel targeting MIPSr1 rather than MIPSr2
to avoid CPU errata.
- Loongson64 gains a couple of fixes, a workaround for a write
buffering issue & support for the Loongson 3A R3.1 CPU.
- Malta now uses the piix4-poweroff driver to handle powering down.
- Microsemi Ocelot gained support for its SPI bus & NOR flash, its
second MDIO bus and can now be supported by a FIT/.itb image.
- Octeon saw a bunch of header cleanups which remove a lot of
duplicate or unused code.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCW3G6JxUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN0n/gD/Rpdgay31G/4eTTKBmBrcaju6Shjt
/2Iu6WC5Sj4hDHUBAJSbuI+B9YjcNsjekBYxB/LLD7ImcLBl6nLMIvKmXLAL
=cUiF
-----END PGP SIGNATURE-----
Merge tag 'mips_4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
"Here are the main MIPS changes for 4.19.
An overview of the general architecture changes:
- Massive DMA ops refactoring from Christoph Hellwig (huzzah for
deleting crufty code!).
- We introduce NT_MIPS_DSP & NT_MIPS_FP_MODE ELF notes &
corresponding regsets to expose DSP ASE & floating point mode state
respectively, both for live debugging & core dumps.
- We better optimize our code by hard-coding cpu_has_* macros at
compile time where their values are known due to the ISA revision
that the kernel build is targeting.
- The EJTAG exception handler now better handles SMP systems, where
it was previously possible for CPUs to clobber a register value
saved by another CPU.
- Our implementation of memset() gained a couple of fixes for MIPSr6
systems to return correct values in some cases where stores fault.
- We now implement ioremap_wc() using the uncached-accelerated cache
coherency attribute where supported, which is detected during boot,
and fall back to plain uncached access where necessary. The
MIPS-specific (and unused in tree) ioremap_uncached_accelerated() &
ioremap_cacheable_cow() are removed.
- The prctl(PR_SET_FP_MODE, ...) syscall is better supported for SMP
systems by reworking the way we ensure remote CPUs that may be
running threads within the affected process switch mode.
- Systems using the MIPS Coherence Manager will now set the
MIPS_IC_SNOOPS_REMOTE flag to avoid some unnecessary cache
maintenance overhead when flushing the icache.
- A few fixes were made for building with clang/LLVM, which now
sucessfully builds kernels for many of our platforms.
- Miscellaneous cleanups all over.
And some platform-specific changes:
- ar7 gained stubs for a few clock API functions to fix build
failures for some drivers.
- ath79 gained support for a few new SoCs, a few fixes & better
gpio-keys support.
- Ci20 now exposes its SPI bus using the spi-gpio driver.
- The generic platform can now auto-detect a suitable value for
PHYS_OFFSET based upon the memory map described by the device tree,
allowing us to avoid wasting memory on page book-keeping for
systems where RAM starts at a non-zero physical address.
- Ingenic systems using the jz4740 platform code now link their
vmlinuz higher to allow for kernels of a realistic size.
- Loongson32 now builds the kernel targeting MIPSr1 rather than
MIPSr2 to avoid CPU errata.
- Loongson64 gains a couple of fixes, a workaround for a write
buffering issue & support for the Loongson 3A R3.1 CPU.
- Malta now uses the piix4-poweroff driver to handle powering down.
- Microsemi Ocelot gained support for its SPI bus & NOR flash, its
second MDIO bus and can now be supported by a FIT/.itb image.
- Octeon saw a bunch of header cleanups which remove a lot of
duplicate or unused code"
* tag 'mips_4.19' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (123 commits)
MIPS: Remove remnants of UASM_ISA
MIPS: netlogic: xlr: Remove erroneous check in nlm_fmn_send()
MIPS: VDSO: Force link endianness
MIPS: Always specify -EB or -EL when using clang
MIPS: Use dins to simplify __write_64bit_c0_split()
MIPS: Use read-write output operand in __write_64bit_c0_split()
MIPS: Avoid using array as parameter to write_c0_kpgd()
MIPS: vdso: Allow clang's --target flag in VDSO cflags
MIPS: genvdso: Remove GOT checks
MIPS: Remove obsolete MIPS checks for DST node "chosen@0"
MIPS: generic: Remove input symbols from defconfig
MIPS: Delete unused code in linux32.c
MIPS: Remove unused sys_32_mmap2
MIPS: Remove nabi_no_regargs
mips: dts: mscc: enable spi and NOR flash support on ocelot PCB123
mips: dts: mscc: Add spi on Ocelot
MIPS: Loongson: Merge load addresses
MIPS: Loongson: Set Loongson32 to MIPS32R1
MIPS: mscc: ocelot: add interrupt controller properties to GPIO controller
MIPS: generic: Select MIPS_AUTO_PFN_OFFSET
...
Add addition argument 'arch_uprobe' to uprobe_write_opcode().
We need this in later set of patches.
Link: http://lkml.kernel.org/r/20180809041856.1547-3-ravi.bangoria@linux.ibm.com
Reviewed-by: Song Liu <songliubraving@fb.com>
Acked-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Pull perf update from Thomas Gleixner:
"The perf crowd presents:
Kernel updates:
- Removal of jprobes
- Cleanup and consolidatation the handling of kprobes
- Cleanup and consolidation of hardware breakpoints
- The usual pile of fixes and updates to PMUs and event descriptors
Tooling updates:
- Updates and improvements all over the place. Nothing outstanding,
just the (good) boring incremental grump work"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (103 commits)
perf trace: Do not require --no-syscalls to suppress strace like output
perf bpf: Include uapi/linux/bpf.h from the 'perf trace' script's bpf.h
perf tools: Allow overriding MAX_NR_CPUS at compile time
perf bpf: Show better message when failing to load an object
perf list: Unify metric group description format with PMU event description
perf vendor events arm64: Update ThunderX2 implementation defined pmu core events
perf cs-etm: Generate branch sample for CS_ETM_TRACE_ON packet
perf cs-etm: Generate branch sample when receiving a CS_ETM_TRACE_ON packet
perf cs-etm: Support dummy address value for CS_ETM_TRACE_ON packet
perf cs-etm: Fix start tracing packet handling
perf build: Fix installation directory for eBPF
perf c2c report: Fix crash for empty browser
perf tests: Fix indexing when invoking subtests
perf trace: Beautify the AF_INET & AF_INET6 'socket' syscall 'protocol' args
perf trace beauty: Add beautifiers for 'socket''s 'protocol' arg
perf trace beauty: Do not print NULL strarray entries
perf beauty: Add a generator for IPPROTO_ socket's protocol constants
tools include uapi: Grab a copy of linux/in.h
perf tests: Fix complex event name parsing
perf evlist: Fix error out while applying initial delay and LBR
...
Pull locking/atomics update from Thomas Gleixner:
"The locking, atomics and memory model brains delivered:
- A larger update to the atomics code which reworks the ordering
barriers, consolidates the atomic primitives, provides the new
atomic64_fetch_add_unless() primitive and cleans up the include
hell.
- Simplify cmpxchg() instrumentation and add instrumentation for
xchg() and cmpxchg_double().
- Updates to the memory model and documentation"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (48 commits)
locking/atomics: Rework ordering barriers
locking/atomics: Instrument cmpxchg_double*()
locking/atomics: Instrument xchg()
locking/atomics: Simplify cmpxchg() instrumentation
locking/atomics/x86: Reduce arch_cmpxchg64*() instrumentation
tools/memory-model: Rename litmus tests to comply to norm7
tools/memory-model/Documentation: Fix typo, smb->smp
sched/Documentation: Update wake_up() & co. memory-barrier guarantees
locking/spinlock, sched/core: Clarify requirements for smp_mb__after_spinlock()
sched/core: Use smp_mb() in wake_woken_function()
tools/memory-model: Add informal LKMM documentation to MAINTAINERS
locking/atomics/Documentation: Describe atomic_set() as a write operation
tools/memory-model: Make scripts executable
tools/memory-model: Remove ACCESS_ONCE() from model
tools/memory-model: Remove ACCESS_ONCE() from recipes
locking/memory-barriers.txt/kokr: Update Korean translation to fix broken DMA vs. MMIO ordering example
MAINTAINERS: Add Daniel Lustig as an LKMM reviewer
tools/memory-model: Fix ISA2+pooncelock+pooncelock+pombonce name
tools/memory-model: Add litmus test for full multicopy atomicity
locking/refcount: Always allow checked forms
...
Pull scheduler updates from Thomas Gleixner:
- Cleanup and improvement of NUMA balancing
- Refactoring and improvements to the PELT (Per Entity Load Tracking)
code
- Watchdog simplification and related cleanups
- The usual pile of small incremental fixes and improvements
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
watchdog: Reduce message verbosity
stop_machine: Reflow cpu_stop_queue_two_works()
sched/numa: Move task_numa_placement() closer to numa_migrate_preferred()
sched/numa: Use group_weights to identify if migration degrades locality
sched/numa: Update the scan period without holding the numa_group lock
sched/numa: Remove numa_has_capacity()
sched/numa: Modify migrate_swap() to accept additional parameters
sched/numa: Remove unused task_capacity from 'struct numa_stats'
sched/numa: Skip nodes that are at 'hoplimit'
sched/debug: Reverse the order of printing faults
sched/numa: Use task faults only if numa_group is not yet set up
sched/numa: Set preferred_node based on best_cpu
sched/numa: Simplify load_too_imbalanced()
sched/numa: Evaluate move once per node
sched/numa: Remove redundant field
sched/debug: Show the sum wait time of a task group
sched/fair: Remove #ifdefs from scale_rt_capacity()
sched/core: Remove get_cpu() from sched_fork()
sched/cpufreq: Clarify sugov_get_util()
sched/sysctl: Remove unused sched_time_avg_ms sysctl
...
Since at least the beginning of the git era we've declared our TLB
exception handling functions inconsistently. They're actually functions,
but we declare them as arrays of u32 where each u32 is an encoded
instruction. This has always been the case for arch/mips/mm/tlbex.c, and
has also been true for arch/mips/kernel/traps.c since commit
86a1708a9d ("MIPS: Make tlb exception handler definitions and
declarations match.") which aimed for consistency but did so by
consistently making the our C code inconsistent with our assembly.
This is all usually harmless, but when using GCC 7 or newer to build a
kernel targeting microMIPS (ie. CONFIG_CPU_MICROMIPS=y) it becomes
problematic. With microMIPS bit 0 of the program counter indicates the
ISA mode. When bit 0 is zero instructions are decoded using the standard
MIPS32 or MIPS64 ISA. When bit 0 is one instructions are decoded using
microMIPS. This means that function pointers become odd - their least
significant bit is one for microMIPS code. We work around this in cases
where we need to access code using loads & stores with our
msk_isa16_mode() macro which simply clears bit 0 of the value it is
given:
#define msk_isa16_mode(x) ((x) & ~0x1)
For example we do this for our TLB load handler in
build_r4000_tlb_load_handler():
u32 *p = (u32 *)msk_isa16_mode((ulong)handle_tlbl);
We then write code to p, expecting it to be suitably aligned (our LEAF
macro aligns functions on 4 byte boundaries, so (ulong)handle_tlbl will
give a value one greater than a multiple of 4 - ie. the start of a
function on a 4 byte boundary, with the ISA mode bit 0 set).
This worked fine up to GCC 6, but GCC 7 & onwards is smart enough to
presume that handle_tlbl which we declared as an array of u32s must be
aligned sufficiently that bit 0 of its address will never be set, and as
a result optimize out msk_isa16_mode(). This leads to p having an
address with bit 0 set, and when we go on to attempt to store code at
that address we take an address error exception due to the unaligned
memory access.
This leads to an exception prior to the kernel having configured its own
exception handlers, so we jump to whatever handlers the bootloader
configured. In the case of QEMU this results in a silent hang, since it
has no useful general exception vector.
Fix this by consistently declaring our TLB-related functions as
functions. For handle_tlbl(), handle_tlbs() & handle_tlbm() we do this
in asm/tlbex.h & we make use of the existing declaration of
tlbmiss_handler_setup_pgd() in asm/mmu_context.h. Our TLB handler
generation code in arch/mips/mm/tlbex.c is adjusted to deal with these
definitions, in most cases simply by casting the function pointers to
u32 pointers.
This allows us to include asm/mmu_context.h in arch/mips/mm/tlbex.c to
get the definitions of tlbmiss_handler_setup_pgd & pgd_current, removing
some needless duplication. Consistently using msk_isa16_mode() on
function pointers means we no longer need the
tlbmiss_handler_setup_pgd_start symbol so that is removed entirely.
Now that we're declaring our functions as functions GCC stops optimizing
out msk_isa16_mode() & a microMIPS kernel built with either GCC 7.3.0 or
8.1.0 boots successfully.
Signed-off-by: Paul Burton <paul.burton@mips.com>
We export tlbmiss_handler_setup_pgd in arch/mips/mm/tlbex.c close to a
declaration of it, rather than close to its definition as is standard.
We've supported exporting symbols in assembly code since commit
22823ab419 ("EXPORT_SYMBOL() for asm"), so move the export to follow
the function's (stub) definition.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Commit 33679a5037 ("MIPS: uasm: Remove needless ISA abstraction")
removed use of the MIPS_ISA preprocessor macro, but left a couple of
unused definitions of it behind.
Remove the dead code.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Use the standard WARN_ON instead.
If a small kernel is desired, WARN_ON can be disabled globally.
Also remove SSB_DEBUG. Besides WARN_ON it only adds a tiny debug check.
Include this check unconditionally.
Signed-off-by: Michael Buesch <m@bues.ch>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In nlm_fmn_send() we have a loop which attempts to send a message
multiple times in order to handle the transient failure condition of a
lack of available credit. When examining the status register to detect
the failure we check for a condition that can never be true, which falls
foul of gcc 8's -Wtautological-compare:
In file included from arch/mips/netlogic/common/irq.c:65:
./arch/mips/include/asm/netlogic/xlr/fmn.h: In function 'nlm_fmn_send':
./arch/mips/include/asm/netlogic/xlr/fmn.h:304:22: error: bitwise
comparison always evaluates to false [-Werror=tautological-compare]
if ((status & 0x2) == 1)
^~
If the path taken if this condition were true all we do is print a
message to the kernel console. Since failures seem somewhat expected
here (making the console message questionable anyway) and the condition
has clearly never evaluated true we simply remove it, rather than
attempting to fix it to check status correctly.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20174/
Cc: Ganesan Ramalingam <ganesanr@broadcom.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Jayachandran C <jnair@caviumnetworks.com>
Cc: John Crispin <john@phrozen.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
When building the VDSO with clang it appears to invoke ld without
specifying endianness, even though clang itself was provided with a -EB
or -EL flag. This results in the build failing due to a mismatch between
the objects that are the input to ld, and the output it is attempting to
create:
VDSO arch/mips/vdso/vdso.so.dbg.raw
mips-linux-ld: arch/mips/vdso/elf.o: compiled for a big endian system
and target is little endian
mips-linux-ld: arch/mips/vdso/elf.o: endianness incompatible with that
of the selected emulation
mips-linux-ld: failed to merge target specific data of file
arch/mips/vdso/elf.o
...
Work around this problem by explicitly specifying the link endianness
using -Wl,-EB or -Wl,-EL when -EB or -EL are part of KBUILD_CFLAGS. This
resolves the build failure when using clang, and doesn't have any
negative effect on gcc.
Signed-off-by: Paul Burton <paul.burton@mips.com>
When building using clang, always specify -EB or -EL in order to ensure
we target the desired endianness.
Since clang cross compiles using a single compiler build with multiple
targets, our -dumpmachine tests which don't specify clang's --target
argument check output based upon the build machine rather than the
machine our build will target. This means our detection of whether to
specify -EB fails miserably & we never do. Providing the endianness flag
unconditionally for clang resolves this issue & simplifies the clang
path somewhat.
Signed-off-by: Paul Burton <paul.burton@mips.com>
The code in __write_64bit_c0_split() is used by MIPS32 kernels running
on MIPS64 CPUs to write a 64-bit value to a 64-bit coprocessor 0
register using a single 64-bit dmtc0 instruction. It does this by
combining the 2x 32-bit registers used to hold the 64-bit value into a
single register, which in the existing code involves three steps:
1) Zero extend register A which holds bits 31:0 of our data, since it
may have previously held a sign-extended value.
2) Shift register B which holds bits 63:32 of our data in bits 31:0
left by 32 bits, such that the bits forming our data are in the
position they'll be in the final 64-bit value & bits 31:0 of the
register are zero.
3) Or the two registers together to form the 64-bit value in one
64-bit register.
From MIPS r2 onwards we have a dins instruction which can effectively
perform all 3 of those steps using a single instruction.
Add a path for MIPS r2 & beyond which uses dins to take bits 31:0 from
register B & insert them into bits 63:32 of register A, giving us our
full 64-bit value in register A with one instruction.
Since we know that MIPS r2 & above support the sel field for the dmtc0
instruction, we don't bother special casing sel==0. Omiting the sel
field would assemble to exactly the same instruction as when we
explicitly specify that it equals zero.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Commit c22c804310 ("MIPS: Fix input modify in
__write_64bit_c0_split()") modified __write_64bit_c0_split() constraints
such that we have both an input & an output which we hope to assign to
the same registers, and modify the output rather than incorrectly
clobbering an input.
The way in which we use both an output & an input parameter with the
input constrained to share the output registers is a little convoluted &
also problematic for clang, which complains if the input & output values
have different widths. For example:
In file included from kernel/fork.c:98:
./arch/mips/include/asm/mmu_context.h:149:19: error: unsupported
inline asm: input with type 'unsigned long' matching output with
type 'unsigned long long'
write_c0_entryhi(cpu_asid(cpu, next));
~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~
./arch/mips/include/asm/mmu_context.h:93:2: note: expanded from macro
'cpu_asid'
(cpu_context((cpu), (mm)) & cpu_asid_mask(&cpu_data[cpu]))
^
./arch/mips/include/asm/mipsregs.h:1617:65: note: expanded from macro
'write_c0_entryhi'
#define write_c0_entryhi(val) __write_ulong_c0_register($10, 0, val)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./arch/mips/include/asm/mipsregs.h:1430:39: note: expanded from macro
'__write_ulong_c0_register'
__write_64bit_c0_register(reg, sel, val); \
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./arch/mips/include/asm/mipsregs.h:1400:41: note: expanded from macro
'__write_64bit_c0_register'
__write_64bit_c0_split(register, sel, value); \
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~
./arch/mips/include/asm/mipsregs.h:1498:13: note: expanded from macro
'__write_64bit_c0_split'
: "r,0" (val)); \
^~~
We can both fix this build failure & simplify the code somewhat by
assigning the __tmp variable with the input value in C prior to our
inline assembly, and then using a single read-write output operand (ie.
a constraint beginning with +) to provide this value to our assembly.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Passing an array (swapper_pg_dir) as the argument to write_c0_kpgd() in
setup_pw() will become problematic if we modify __write_64bit_c0_split()
to cast its val argument to unsigned long long, because for 32-bit
kernel builds the size of a pointer will differ from the size of an
unsigned long long. This would fall foul of gcc's pointer-to-int-cast
diagnostic.
Cast the value to a long, which should be the same width as the pointer
that we ultimately want & will be sign extended if required to the
unsigned long long that __write_64bit_c0_split() ultimately needs.
Signed-off-by: Paul Burton <paul.burton@mips.com>
The MIPS VDSO code filters out a subset of known-good flags from
KBUILD_CFLAGS to use when building VDSO libraries. When we build using
clang we need to allow the --target flag through, otherwise we'll
generally attempt to build the VDSO for the architecture of the build
machine rather than for MIPS.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Patchwork: https://patchwork.linux-mips.org/patch/20154/
Cc: James Hogan <jhogan@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: linux-mips@linux-mips.org
