Make use of USB quirk method to identify such HDD while reading
the cache status in sd_probe(). If cache quirk is present for
the HDD, lets assume that cache is enabled and make WCE bit
equal to 1.
Signed-off-by: Namjae Jeon <namjae.jeon@samsung.com>
Signed-off-by: Pankaj Kumar <pankaj.km@samsung.com>
Signed-off-by: Amit Sahrawat <a.sahrawat@samsung.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This has scsi_internal_device_unblock/scsi_target_unblock take
the new state to set the devices as an argument instead of
always setting to running. The patch also converts users of these
functions.
This allows the FC and iSCSI class to transition devices from blocked
to transport-offline, so that when fast_io_fail/replacement_timeout
has fired we do not set the devices back to running. Instead, we
set them to SDEV_TRANSPORT_OFFLINE.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds a new state SDEV_TRANSPORT_OFFLINE. It will
be used by transport classes to offline devices for cases like
when the fast_io_fail/recovery_tmo fires. In those cases we
want all IO to fail, and we have not yet escalated to dev_loss_tmo
behavior where we are removing the devices.
Currently to handle this state, transport classes are setting
the scsi_device's state to running, setting their internal
session/port structs state to something that indicates failed,
and then failing IO from some transport check in the queuecommand.
The reason for the new value is so that users can distinguish
between a device failure that is a result of a transport problem
vs the wide range of errors that devices get offlined for
when a scsi command times out and we offline the devices there.
It also fixes the confusion as to why the transport class is
failing IO, but has set the device state from blocked to running.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If ATA device supports "Device Attention", then tell scsi layer that
the device supports runtime power off.
Signed-off-by: Aaron Lu <aaron.lu@amd.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Several bug reports have been received recently for USB mass-storage
devices that don't handle READ CAPACITY(16) commands properly. They
report bogus sizes, in some cases becoming unusable as a result.
The bugs were triggered by commit
09b6b51b0b (SCSI & usb-storage: add
flags for VPD pages and REPORT LUNS), which caused usb-storage to stop
overriding the SCSI level reported by devices. By default, the sd
driver will try READ CAPACITY(16) first for any device whose level is
above SCSI_SPC_2.
It seems likely that any device large enough to require the use of
READ CAPACITY(16) (i.e., 2 TB or more) would be able to handle READ
CAPACITY(10) commands properly. Indeed, I don't know of any devices
that don't handle READ CAPACITY(10) properly.
Therefore this patch (as1559) adds a new flag telling the sd driver
to try READ CAPACITY(10) before READ CAPACITY(16), and sets this flag
for every USB mass-storage device. If a device really is larger than
2 TB, sd will fall back to READ CAPACITY(16) just as it used to.
This fixes Bugzilla #43391.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
"[RFC PATCH 0/2] audit of linux/device.h users in include/*"
https://lkml.org/lkml/2012/3/4/159
--
Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then
one to delete the device.h includes from the linux/include/ dir
wherever possible.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPbNxLAAoJEOvOhAQsB9HWR6QQAMRUZ94O2069/nW9h4TO/xTr
Hq/80lo/TBBiRmob3iWBP76lzgeeMPPVEX1I6N7YYlhL3IL7HsaJH1DvpIPPHXQP
GFKcBsZ5ZLV8c4CBDSr+/HFNdhXc0bw0awBjBvR7gAsWuZpNFn4WbhizJi4vWAoE
4ydhPu55G1G8TkBtYLJQ8xavxsmiNBSDhd2i+0vn6EVpgmXynjOMG8qXyaS97Jvg
pZLwnN5Wu21coj6+xH3QUKCl1mJ+KGyamWX5gFBVIfsDB3k5H4neijVm7t1en4b0
cWxmXeR/JE3VLEl/17yN2dodD8qw1QzmTWzz1vmwJl2zK+rRRAByBrL0DP7QCwCZ
ppeJbdhkMBwqjtknwrmMwsuAzUdJd79GXA+6Vm+xSEkr6FEPK1M0kGbvaqV9Usgd
ohMewewbO6ddgR9eF7Kw2FAwo0hwkPNEplXIym9rZzFG1h+T0STGSHvkn7LV765E
ul1FapSV3GCxEVRwWTwD28FLU2+0zlkOZ5sxXwNPTT96cNmW+R7TGuslZKNaMNjX
q7eBZxo8DtVt/jqJTntR8bs8052c8g1Ac1IKmlW8VSmFwT1M6VBGRn1/JWAhuUgv
dBK/FF+I1GJTAJWIhaFcKXLHvmV9uhS6JaIhLMDOetoOkpqSptJ42hDG+89WkFRk
o55GQ5TFdoOpqxVzGbvE
=3j4+
-----END PGP SIGNATURE-----
Merge tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull <linux/device.h> avoidance patches from Paul Gortmaker:
"Nearly every subsystem has some kind of header with a proto like:
void foo(struct device *dev);
and yet there is no reason for most of these guys to care about the
sub fields within the device struct. This allows us to significantly
reduce the scope of headers including headers. For this instance, a
reduction of about 40% is achieved by replacing the include with the
simple fact that the device is some kind of a struct.
Unlike the much larger module.h cleanup, this one is simply two
commits. One to fix the implicit <linux/device.h> users, and then one
to delete the device.h includes from the linux/include/ dir wherever
possible."
* tag 'device-for-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
device.h: audit and cleanup users in main include dir
device.h: cleanup users outside of linux/include (C files)
The <linux/device.h> header includes a lot of stuff, and
it in turn gets a lot of use just for the basic "struct device"
which appears so often.
Clean up the users as follows:
1) For those headers only needing "struct device" as a pointer
in fcn args, replace the include with exactly that.
2) For headers not really using anything from device.h, simply
delete the include altogether.
3) For headers relying on getting device.h implicitly before
being included themselves, now explicitly include device.h
4) For files in which doing #1 or #2 uncovers an implicit
dependency on some other header, fix by explicitly adding
the required header(s).
Any C files that were implicitly relying on device.h to be
present have already been dealt with in advance.
Total removals from #1 and #2: 51. Total additions coming
from #3: 9. Total other implicit dependencies from #4: 7.
As of 3.3-rc1, there were 110, so a net removal of 42 gives
about a 38% reduction in device.h presence in include/*
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This patch (as1507) adds a skip_vpd_pages flag to struct scsi_device
and a no_report_luns flag to struct scsi_target. The first is used to
control whether sd will look at VPD pages for information on block
provisioning, limits, and characteristics. The second prevents
scsi_report_lun_scan() from issuing a REPORT LUNS command.
The patch also modifies usb-storage to set the new flag bits for all
USB devices and targets, and to stop adjusting the scsi_level value.
Historically we have seen that USB mass-storage devices often don't
support VPD pages or REPORT LUNS properly. Until now we have avoided
these things by setting the scsi_level to SCSI_2 for all USB devices.
But this has the side effect of storing the LUN bits into the second
byte of each CDB, and now we have a report of a device which doesn't
like that. The best solution is to stop abusing scsi_level and
instead have separate flags for VPD pages and REPORT LUNS.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Perry Wagle <wagle@mac.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1506) corrects a typo in the definition of the
scsi_target structure. pdt_1f_for_no_lun is supposed to be a
single-bit flag, not a full-sized integer.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All the handlers have now implemented the match function so We don't need to
use scsi_dev_info any more for matching purposes.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Some device handler types are not tied to the vendor/model
but rather to a specific capability. Eg ALUA is supported
if the 'TPGS' setting in the standard inquiry is set.
This patch implements a 'match' callback for device handler
which supersedes the original vendor/model lookup and
implements the callback for the ALUA handler.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Instead of issuing a standard inquiry from within the
alua device handler we can evaluate the TPGS setting from
the existing inquiry data of the sdev and save us the I/O.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: Arun Sharma <asharma@fb.com>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit c21e6beb removed our queue request_fn re-enter
protection, and defaulted to always running the queues from
kblockd to be safe. This was a known potential slow down,
but should be safe.
Unfortunately this is causing big performance regressions for
some, so we need to improve this logic. Looking into the details
of the re-enter, the real issue is on requeue of requests.
Requeue of requests upon seeing a BUSY condition from the device
ends up re-running the queue, causing traces like this:
scsi_request_fn()
scsi_dispatch_cmd()
scsi_queue_insert()
__scsi_queue_insert()
scsi_run_queue()
scsi_request_fn()
...
potentially causing the issue we want to avoid. So special
case the requeue re-run of the queue, but improve it to offload
the entire run of local queue and starved queue from a single
workqueue callback. This is a lot better than potentially
kicking off a workqueue run for each device seen.
This also fixes the issue of the local device going into recursion,
since the above mentioned commit never moved that queue run out
of line.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
During device discovery, scsi mid layer sends INQUIRY command to LUN
0. If the LUN 0 is not mapped to host, it creates a temporary
scsi_device with LUN id 0 and sends REPORT_LUNS command to it. After
the REPORT_LUNS succeeds, it walks through the LUN table and adds each
LUN found to sysfs. At the end of REPORT_LUNS lun table scan, it will
delete the temporary scsi_device of LUN 0.
When scsi devices are added to sysfs, it calls add_dev function of all
the registered class interfaces. If ses driver has been registered,
ses_intf_add() of ses module will be called. This function calls
scsi_device_enclosure() to check the inquiry data for EncServ
bit. Since inquiry was not allocated for temporary LUN 0 scsi_device,
it will cause NULL pointer exception.
To fix the problem, sdev->inquiry is checked for NULL before reading it.
Signed-off-by: Somasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Signed-off-by: Babu Moger <babu.moger@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Previously we were using strncmp in order to avoid having to include
whitespace in the devlist, but this means "HSV1000" matches a device
list entry that says "HSV100", which is wrong. This patch changes
scsi_dh.c to use scsi_devinfo's matching functions instead, since they
handle these cases correctly.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
I seem to have a knack for digging up buggy usb devices which don't work
with Linux, and I'm crazy enough to try to make them work. So this time a
friend of mine asked me to get an mp4 player (an mp3 player which can play
videos on a small screen) to work with Linux.
It is based on the well known rockbox chipset for which we already have an
unusual devs entries to work around some of its bugs. But this model
comes with an additional twist.
This model chokes on read_capacity_16 calls. Now normally we don't make
those calls, but this model comes with an sdcard slot and when there is no
card in there (and shipped from the factory there is none), it reports a
size of 0. However this time the programmers actually got the
read_capacity_10 response right! So they substract one from the size as
stored internally in the mp3 player before reporting it back, resulting in
an answer of ... 0xffffffff sectors, causing sd.c to try a
read_capacity_16, on which the device crashes.
This patch adds a flag to scsi_device to indicate that a a device cannot
handle read_capacity_16, and when this flag is set if a device reports an
lba of 0xffffffff as answer to a read_capacity_10, assumes it tries to
report a size of 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some USB devices emulate a usb-mass-storage attached (scsi) cdrom device,
usually this fake cdrom contains the windows software for the device.
While working on supporting Appotech ax3003 based photoframes, which do
this I discovered that they will go of into lala land when ever they see a
READ_DISC_INFO scsi command.
Thus this patch adds a scsi_device flag (which can then be set by the
usb-storage driver through an unsual-devs entry), to indicate this, and
makes the sr driver honor this flag.
I know this sucks, but as discussed on linux-scsi list there is no other
way to make this device work properly.
Looking at usb traces made under windows, windows never sends a
READ_DISC_INFO during normal interactions with a usb cdrom device. So as
this cdrom emulation thingie becomes more common we might see more of this
problem.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1398b) adds runtime PM support to the SCSI layer. Only
the machanism is provided; use of it is up to the various high-level
drivers, and the patch doesn't change any of them. Except for sg --
the patch expicitly prevents a device from being runtime-suspended
while its sg device file is open.
The implementation is simplistic. In general, hosts and targets are
automatically suspended when all their children are asleep, but for
them the runtime-suspend code doesn't actually do anything. (A host's
runtime PM status is propagated up the device tree, though, so a
runtime-PM-aware lower-level driver could power down the host adapter
hardware at the appropriate times.) There are comments indicating
where a transport class might be notified or some other hooks added.
LUNs are runtime-suspended by calling the drivers' existing suspend
handlers (and likewise for runtime-resume). Somewhat arbitrarily, the
implementation delays for 100 ms before suspending an eligible LUN.
This is because there typically are occasions during bootup when the
same device file is opened and closed several times in quick
succession.
The way this all works is that the SCSI core increments a device's
PM-usage count when it is registered. If a high-level driver does
nothing then the device will not be eligible for runtime-suspend
because of the elevated usage count. If a high-level driver wants to
use runtime PM then it can call scsi_autopm_put_device() in its probe
routine to decrement the usage count and scsi_autopm_get_device() in
its remove routine to restore the original count.
Hosts, targets, and LUNs are not suspended while they are being probed
or removed, or while the error handler is running. In fact, a fairly
large part of the patch consists of code to make sure that things
aren't suspended at such times.
[jejb: fix up compile issues in PM config variations]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The best way to fix this is to eliminate the intenal kmalloc() and
make the caller allocate the required amount of storage.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (222 commits)
[SCSI] zfcp: Remove flag ZFCP_STATUS_FSFREQ_TMFUNCNOTSUPP
[SCSI] zfcp: Activate fc4s attributes for zfcp in FC transport class
[SCSI] zfcp: Block scsi_eh thread for rport state BLOCKED
[SCSI] zfcp: Update FSF error reporting
[SCSI] zfcp: Improve ELS ADISC handling
[SCSI] zfcp: Simplify handling of ct and els requests
[SCSI] zfcp: Remove ZFCP_DID_MASK
[SCSI] zfcp: Move WKA port to zfcp FC code
[SCSI] zfcp: Use common code definitions for FC CT structs
[SCSI] zfcp: Use common code definitions for FC ELS structs
[SCSI] zfcp: Update FCP protocol related code
[SCSI] zfcp: Dont fail SCSI commands when transitioning to blocked fc_rport
[SCSI] zfcp: Assign scheduled work to driver queue
[SCSI] zfcp: Remove STATUS_COMMON_REMOVE flag as it is not required anymore
[SCSI] zfcp: Implement module unloading
[SCSI] zfcp: Merge trace code for fsf requests in one function
[SCSI] zfcp: Access ports and units with container_of in sysfs code
[SCSI] zfcp: Remove suspend callback
[SCSI] zfcp: Remove global config_mutex
[SCSI] zfcp: Replace local reference counting with common kref
...
Make scsi_dh_activate() function asynchronous, by taking in two additional
parameters, one is the callback function and the other is the data to call
the callback function with.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Current FC HBA queue_depth ramp up code depends on last queue
full time. The sdev already has last_queue_full_time field to
track last queue full time but stored value is truncated by
last four bits.
So this patch updates last_queue_full_time without truncating
last 4 bits to store full value and then updates its only
current usages in scsi_track_queue_full to ignore last four bits
to keep current usages same while also use this field
in added ramp up code.
Adds scsi_handle_queue_ramp_up to ramp up queue_depth on
successful completion of IO. The scsi_handle_queue_ramp_up will
do ramp up on all luns of a target, just same as ramp down done
on all luns on a target.
The ramp up is skipped in case the change_queue_depth is not
supported by LLD or already reached to added max_queue_depth.
Updates added max_queue_depth on every new update to default
queue_depth value.
The ramp up is also skipped if lapsed time since either last
queue ramp up or down is less than LLD specified
queue_ramp_up_period.
Adds queue_ramp_up_period to sysfs but only if change_queue_depth
is supported since ramp up and queue_ramp_up_period is needed only
in case change_queue_depth is supported first.
Initializes queue_ramp_up_period to 120HZ jiffies as initial
default value, it is same as used in existing lpfc and qla2xxx.
-v2
Combined all ramp code into this single patch.
-v3
Moves max_queue_depth initialization after slave_configure is
called from after slave_alloc calling done. Also adjusted
max_queue_depth check to skip ramp up if current queue_depth
is >= max_queue_depth.
-v4
Changes sdev->queue_ramp_up_period unit to ms when using sysfs i/f
to store or show its value.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Tested-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Async scanning introduced a very wide window where the SCSI device is
up and running but has not yet been added to sysfs. We delay the
adding until all scans have completed to retain the same ordering as
sync scanning.
This delay in visibility causes an oops if a device is removed before
we make it visible because the SCSI removal routines have an inbuilt
assumption that if a device is in SDEV_RUNNING state, it must be
visible (which is not necessarily true in the async scanning case).
Fix this by introducing an additional is_visible flag which we can use
to condition the tear down so we do the right thing for running but
not yet made visible.
Reported-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When we moved the device handler functionality from dm layer to SCSI layer
we dropped the parameter functionality.
This path adds an interface to scsi dh layer to set device handler
parameters.
Basically, multipath layer need to create a string with all the parameters
and call scsi_dh_set_params() after it called scsi_dh_attach() on a
device.
If a device handler provides such an interface it will handle the parameters
as it expects them.
Reported-by: Eddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Tested-by: Eddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Problem reported: http://marc.info/?l=dm-devel&m=124585978305866&w=2
scsi_dh does not do a refernce count for attach/detach, and this affects
the way it is supposed to work with multipath when a device is not
in the dev_list of the hardware handler.
This patch adds a reference count that counts each attach.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
No one uses scsi_execute_async with data transfer now. We can remove
scsi_req_map_sg.
Only scsi_eh_lock_door uses scsi_execute_async. scsi_eh_lock_door
doesn't handle sense and the callback. So we can remove
scsi_io_context too.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_device_online() is not just a negation of SDEV_OFFLINE,
also devices in state SDEV_DEL are actually offline.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Based on prior work by Martin Petersen and James Bottomley, this patch
adds a generic helper for retrieving VPD pages from SCSI devices.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
scsi_execute() and scsi_execute_req() discard the residual length
information. Some callers need it. This adds residual argument
(optional) to scsi_execute and scsi_execute_req.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
by removing the unused timeout parameter we ensure a compile failure if
anyone is accidentally still using it rather than the block timeout.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
SCSI-ml manages the queueing limits for the device and host, but
does not do so at the target level. However something something similar
can come in userful when a driver is transitioning a transport object to
the the blocked state, becuase at that time we do not want to queue
io and we do not want the queuecommand to be called again.
The patch adds code similar to the exisiting SCSI_ML_*BUSY handlers.
You can now return SCSI_MLQUEUE_TARGET_BUSY when we hit
a transport level queueing issue like the hw cannot allocate some
resource at the iscsi session/connection level, or the target has temporarily
closed or shrunk the queueing window, or if we are transitioning
to the blocked state.
bnx2i, when they rework their firmware according to netdev
developers requests, will also need to be able to limit queueing at this
level. bnx2i will hook into libiscsi, but will allocate a scsi host per
netdevice/hba, so unlike pure software iscsi/iser which is allocating
a host per session, it cannot set the scsi_host->can_queue and return
SCSI_MLQUEUE_HOST_BUSY to reflect queueing limits on the transport.
The iscsi class/driver can also set a scsi_target->can_queue value which
reflects the max commands the driver/class can support. For iscsi this
reflects the number of commands we can support for each session due to
session/connection hw limits, driver limits, and to also reflect the
session/targets's queueing window.
Changes:
v1 - initial patch.
v2 - Fix scsi_run_queue handling of multiple blocked targets.
Previously we would break from the main loop if a device was added back on
the starved list. We now run over the list and check if any target is
blocked.
v3 - Rediff for scsi-misc.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Brian King <brking@linux.vnet.ibm.com> reported that fibre channel
devices can oops during scanning if their ports block (because the
device goes from CREATED -> BLOCK -> RUNNING rather than CREATED ->
BLOCK -> CREATED).
Fix this by adding a new state: CREATED_BLOCK which can only transition
back to CREATED and disallow the CREATED -> BLOCK transition. Now both
the created and blocked states that the mid-layer recognises can include
CREATED_BLOCK.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The created and blocked states are very shortly going to correspond to
mixed sdev_state states.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some USB devices set the protect bit in the INQUIRY data which
currently causes the DIF code in sd to assume (incorrectly) that they
support READ_CAPACITY(16). Fix this (only for the time being) by
making sure we only believe the protect bit in the inquiry data if the
device claims conformance to SCSI-3 or above.
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This re-introduces commit 2b14290078,
which was reverted due to the regression it caused by commit
fca082c9f1.
That regression was not root-caused by the original commit, it was just
uncovered by it, and the real fix was done by Alan Stern in commit
580da34847 ("Fix USB storage hang on
command abort").
We can thus re-introduce the change that was confirmed by Alan Jenkins
to be still required by his odd card reader.
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 2b14290078, since it
seems to break some other USB storage devices (at least a JMicron USB to
ATA bridge). As such, while it apparently fixes some cardreaders, it
would need to be made conditional on the exact reader it fixes in order
to avoid causing regressions.
Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The last_sector_bug flag was added to work around a bug in certain usb
cardreaders, where they would crash if a multiple sector read included the
last sector. The original implementation avoids this by e.g. splitting an 8
sector read which includes the last sector into a 7 sector read, and a single
sector read for the last sector. The flag is enabled for all USB devices.
This revealed a second bug in other usb cardreaders, which crash when they
get a multiple sector read which stops 1 sector short of the last sector.
Affected hardware includes the Kingston "MobileLite" external USB cardreader
and the internal USB cardreader on the Asus EeePC.
Extend the last_sector_bug workaround to ensure that any access which touches
the last 8 hardware sectors of the device is a single sector long. Requests
are shrunk as necessary to meet this constraint.
This gives us a safety margin against potential unknown or future bugs
affecting multi-sector access to the end of the device. The two known bugs
only affect the last 2 sectors. However, they suggest that these devices
are prone to fencepost errors and that multi-sector access to the end of the
device is not well tested. Popular OS's use multi-sector accesses, but they
rarely read the last few sectors. Linux (with udev & vol_id) automatically
reads sectors from the end of the device on insertion. It is assumed that
single sector accesses are more thoroughly tested during development.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Implement support for DMA of protection information for devices that
are data integrity capable.
- Add support for mapping an extra scatter-gather list containing
the protection information.
- Allocate protection scsi_data_buffer if host is DIX (integrity DMA)
capable.
- Accessor function for checking whether a device has protection
enabled.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Instead of having each and every driver implement its own
device table scanning code we should rather implement a common
routine and scan the device tables there.
This allows us also to implement a general notifier chain
callback for all device handler instead for one per handler.
[sekharan: Fix rejections caused by conflicting bug fix]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (102 commits)
[SCSI] scsi_dh: fix kconfig related build errors
[SCSI] sym53c8xx: Fix bogus sym_que_entry re-implementation of container_of
[SCSI] scsi_cmnd.h: remove double inclusion of linux/blkdev.h
[SCSI] make struct scsi_{host,target}_type static
[SCSI] fix locking in host use of blk_plug_device()
[SCSI] zfcp: Cleanup external header file
[SCSI] zfcp: Cleanup code in zfcp_erp.c
[SCSI] zfcp: zfcp_fsf cleanup.
[SCSI] zfcp: consolidate sysfs things into one file.
[SCSI] zfcp: Cleanup of code in zfcp_aux.c
[SCSI] zfcp: Cleanup of code in zfcp_scsi.c
[SCSI] zfcp: Move status accessors from zfcp to SCSI include file.
[SCSI] zfcp: Small QDIO cleanups
[SCSI] zfcp: Adapter reopen for large number of unsolicited status
[SCSI] zfcp: Fix error checking for ELS ADISC requests
[SCSI] zfcp: wait until adapter is finished with ERP during auto-port
[SCSI] ibmvfc: IBM Power Virtual Fibre Channel Adapter Client Driver
[SCSI] sg: Add target reset support
[SCSI] lib: Add support for the T10 (SCSI) Data Integrity Field CRC
[SCSI] sd: Move scsi_disk() accessor function to sd.h
...
Adds a new scsi_device flag, start_stop_pwr_cond: If enabled, the sd
driver will not send plain START STOP UNIT commands but ones with the
power condition field set to 3 (standby) or 1 (active) respectively.
Some FireWire disk firmwares do not stop the motor if power condition is
zero. Or worse, they become unresponsive after a START STOP UNIT with
power condition = 0 and start = 0.
http://lkml.org/lkml/2008/4/29/704
This patch only adds the necessary code to sd_mod but doesn't activate
it. Follow-up patches to the FireWire drivers will add detection of
affected devices and enable the code for them.
I did not add power condition values to scsi_error.c::scsi_eh_try_stu()
for now. The three firmwares which suffer from above mentioned problems
do not need START STOP UNIT in the error handler, and they are not
adversely affected by START STOP UNIT with power condition = 0 and start
= 1 (like scsi_eh_try_stu() sends it if scsi_device.allow_restart is
enabled).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: Tino Keitel <tino.keitel@gmx.de>
Some of the storage devices (that can be accessed through multiple paths),
do need some special handling for
1. Activating the passive path of the storage access.
2. Decode and handle the special sense codes returned by the devices.
3. Handle the I/Os being sent to the passive path, especially
during the device probe time.
when accessed through multiple paths.
As of today this special device handling is done at the dm-multipath
layer using dm-handlers. That works well for (1); for (2) to be handled
at dm layer, scsi sense information need to be exported from SCSI to dm-layer,
which is not very attractive; (3) cannot be done at all at the dm layer.
Device handler has been moved to SCSI mainly to handle (2) and (3) properly.
Signed-off-by: Chandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: Mike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current target allocation code registeres each possible target
with sysfs; it will be deleted again if no useable LUN on this target
was found. This results in a string of 'target add/target remove' uevents.
Based on a patch by Hannes Reinecke <hare@suse.de> this patch reworks
the target allocation code so that only uevents for existing targets
are sent. The sysfs registration is split off from the existing
scsi_target_alloc() into a in a new scsi_add_target() function, which
should be called whenever an existing target is found. Only then a
uevent is sent, so we'll be generating events for existing targets
only.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds a new scsi_device flag (last_sector_bug) for devices
which contain a bug where the device crashes when the last sector is
read in a larger then 1 sector read.
This is for example the case with sdcards in the HP PSC1350 printer
cardreader and in the HP PSC1610 printer cardreader.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The current scsi_test_unit_ready() is updated to return sense code
information (in struct scsi_sense_hdr). The sd and sr drivers are
changed to interpret the sense code return asc 0x3a as no media and
adjust the device status accordingly.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Some SCSI tape medium changers that need the BLIST_SINGLELUN flag have
the medium changer at one LUN and the tape drive at a different LUN.
The inquiry string of the tape drive may be different from that of the
medium changer. In order for single_lun to be effective, every
scsi_device under a given scsi_target must have it set. This means that
there needs to be a blacklist entry for BOTH the medium changer AND the
tape drive, which is impractical because some medium changers may be
paired with a variety of different tape drive models. It makes more
sense to put the single_lun flag in scsi_target instead of scsi_device,
which causes every device at a given target ID to inherit the single_lun
flag from one LUN. This makes it possible to blacklist just the medium
changer and not the tape drive.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The esp_reset_cleanup() function is called with the host lock held and
invokes starget_for_each_device() which wants to take it too. Here is a
fix along the lines of shost_for_each_device()/__shost_for_each_device()
adding a __starget_for_each_device() counterpart which assumes the lock
has already been taken.
Eventually, I think the driver should get modified so that more work is
done as a softirq rather than in the interrupt context, but for now it
fixes a bug that causes the spinlock debugger to fire.
While at it, it fixes a small number of cosmetic problems with
starget_for_each_device() too.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removes an obsolete method scsi_device_cancel which isn't being used
anywhere in the kernel.
Signed-off-by: Priyanka Gupta <priyankag@google.com>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When reporting SCSI devices to the SCSI midlayer, use the FCP LUN as
LUN reported to the SCSI layer. With this approach, zfcp does not have
to create unique LUNS, and this code can be removed.
Signed-off-by: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The following patch adds support for sysfs/uevent modalias
attribute for scsi devices (like disks, tapes, cdroms etc),
based on whatever current sd.c, sr.c, st.c and osst.c drivers
supports.
The modalias format is like this:
scsi:type-0x04
(for TYPE_WORM, handled by sr.c now).
Several comments.
o This hexadecimal type value is because all TYPE_XXX constants
in include/scsi/scsi.h are given in hex, but __stringify() will
not convert them to decimal (so it will NOT be scsi:type-4).
Since it does not really matter in which format it is, while
both modalias in module and modalias attribute match each other,
I descided to go for that 0x%02x format (and added a comment in
include/scsi/scsi.h to keep them that way), instead of changing
them all to decimal.
o There was no .uevent routine for SCSI bus. It might be a good
idea to add some more ueven environment variables in there.
o osst.c driver handles tapes too, like st.c, but only SOME tapes.
With this setup, hotplug scripts (or whatever is used by the
user) will try to load both st and osst modules for all SCSI
tapes found, because both modules have scsi:type-0x01 alias).
It is not harmful, but one extra module is no good either.
It is possible to solve this, by exporting more info in
modalias attribute, including vendor and device identification
strings, so that modalias becomes something like
scsi:type-0x12:vendor-Adaptec LTD:device-OnStream Tape Drive
and having that, match for all 3 attributes, not only device
type. But oh well, vendor and device strings may be large,
and they do contain spaces and whatnot.
So I left them for now, awaiting for comments first.
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Implement SBC START/STOP management. sdev->mange_start_stop is added.
When it's set to one, sd STOPs the device on suspend and shutdown and
STARTs it on resume. sdev->manage_start_stop defaults is in sdev
instead of scsi_disk cdev to allow ->slave_config() override the
default configuration but is exported under scsi_disk sysfs node as
sdev->allow_restart is.
When manage_start_stop is zero (the default value), this patch doesn't
introduce any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Rejections fixed and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch enhances SCSI error printing by:
- Making use of scsi_print_result() in the completion functions.
- Having scmd_printk() output the disk name (when applicable).
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
there's a USB mass storage device which exists in two version. One
reports the correct size and the other does not. Apart from that they
are identical and cannot be told apart. Here's a heuristic based on the
empirical finding that drives have even sizes.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since it often takes around 20-30 seconds to scan a scsi bus, it's
highly advantageous to do this in parallel with other things. The bulk
of this patch is ensuring that devices don't change numbering, and that
all devices are discovered prior to trying to start init. For those
who build SCSI as modules, there's a new scsi_wait_scan module that will
ensure all bus scans are finished.
This patch only handles drivers which call scsi_scan_host. Fibre Channel,
SAS, SATA, USB and Firewire all need additional work.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
device_reprobe() should return an error code. When it does so,
scsi_device_reprobe() should propagate it back.
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Original from Christoph Hellwig and Eric Moore. This version exports
the scsi_reprobe_device() function as an inline.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In order to use the new execute_in_process_context() API, you have to
provide it with the work storage, which I do in SCSI in scsi_device and
scsi_target, but which also means that we can no longer queue up the
target reaps, so instead I moved the target to a state model which
allows target_alloc to detect if we've received a dying target and wait
for it to be gone. Hopefully, this should also solve the target
namespace race.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some non-standard SCSI targets or protocols, such as USB UFI, report "no
LUN present" by setting the Peripheral Device Type to 0x1f and the
Peripheral Qualifier to 0 (not 3 as the standard requires) in the INQUIRY
response. This patch (as650b) adds a new target flag and code to
accomodate such targets.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As devfs has been disabled from the kernel tree for a number of months
now (5 to be exact), here's a patch against 2.6.16-rc1-git1 that removes
support for it from the SCSI subsystem.
The patch also removes the scsi_disk devfs_name field as it's no longer
needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
When the scsi_execute_async interface was added it ended up reducing
the flexibility of userspace to send arbitrary scsi commands through
sg using SG_IO. The SG_IO interface allows userspace to specify the
CDB length. This is now ignored in scsi_execute_async and it is
guessed using the COMMAND_SIZE macro, which is not always correct,
particularly for vendor specific commands. This patch adds a cmd_len
parameter to the scsi_execute_async interface to allow the caller
to specify the length of the CDB.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add scsi helpers to create really-large-requests and convert
scsi-ml to scsi_execute_async().
Per Jens's previous comments, I placed this function in scsi_lib.c.
I made it follow all the queue's limits - I think I did at least :), so
I removed the warning on the function header.
I think the scsi_execute_* functions should eventually take a request_queue
and be placed some place where the dm-multipath hw_handler can use them
if that failover code is going to stay in the kernel. That conversion
patch will be sent in another mail though.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make the vendor, model and rev fields in scsi_device pointers to const
and update a few prototypes of functions using them.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
New dev_printk wrappers, which allow us to shrink code, and
eliminate direct references to host/channel/id/lun members:
scmd_printk()
Introduce wrappers for highly common idioms, which may also help us
eliminate some ->{channel,id} references in the future:
{scmd,sdev}_id()
{scmd,sdev}_channel()
The scmd_* wrappers are present in scsi/scsi_device.h because they all
employ the dereference chain cmd->device->$member. We would prefer to
use static inline functions rather than macros, but that would have a
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This should eliminate (at least in the mid layer) to make numeric
assumptions about any of the enumeration variables. As a side effect,
it will also make all the messages consistent and line us up nicely for
the error logging strategy (if it ever shows itself again).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently we just ignore the device, which means there are a few
arrays out there that we don't find.
This patch updates the scsi_report_lun_scan() to take a target instead
of a device so it can be called on a return of
SCSI_SCAN_TARGET_PRESENT, which is what a PQ 3 device returns.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The original API returned either an ERR_PTR() or a refcounted sdev.
Unfortunately, if it's successful, you need to do a scsi_device_put() on
the sdev otherwise the refcounting is wrong.
Everyone seems to expect that scsi_add_device() should be callable
without doing the ref put, so alter the API so it is (we still have
__scsi_add_device with the original behaviour).
The only actual caller that needs altering is the one in firewire ...
not because it gets this right, but because it acts on the error if one
is returned.
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This one removes struct scsi_request entirely from sd. In the process,
I noticed we have no callers of scsi_wait_req who don't immediately
normalise the sense, so I updated the API to make it take a struct
scsi_sense_hdr instead of simply a big sense buffer.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This one's slightly more difficult. The transport class uses
REQ_FAILFAST, so another interface (scsi_execute) had to be invented to
take the extra flag. Also, the sense functions are shifted around to
allow spi_execute to place data directly into a struct scsi_sense_hdr.
With this change, there's probably a lot of unnecessary sense buffer
allocation going on which we can fix later.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
After this, we just have some drivers, all the ULDs and the SPI
transport class using scsi_wait_req().
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
int_to_scsilun() takes a pointer to a struct scsi_lun in it's
prototype, so add this structure to scsi_device.h to avoid declaration
inside function prototype warnings.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
One of the issues we had was reverting the midlayers lun value
into the 8byte lun value that we wanted to send to the device.
Historically, there's been some combination of byte swapping,
setting high/low, etc. There's also been no common thread between
how our driver did it and others. I also got very confused as
to why byteswap routines were being used.
Anyway, this patch is a LLDD-callable function that reverts the
midlayer's lun value, stored in an int, to the 8-byte quantity
(note: this is not the real 8byte quantity, just the same amount
that scsilun_to_int() was able to convert and store originally).
This also solves the dilemma of the thread:
http://marc.theaimsgroup.com/?l=linux-kernel&m=112116767118981&w=2
A patch for the lpfc driver to use this function will be along
in a few days (batched with other patches).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This gives the HBA driver notice when a target is created and
destroyed to allow it to manage its own target based allocations
accordingly.
This is a much reduced verson of the original patch sent in by
James.Smart@Emulex.com
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch removes volatile qualifier from scsi_device->device_busy,
Scsi_Host->host_busy and ->host_failed as the volatile qualifiers
don't serve any purpose now. While at it, convert those fields from
unsigned short to unsigned int as suggested by Christoph.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- add a comment to the device structure that the device_busy field
is now protected by the request_queue->queue_lock
- null out sdev->request_queue after the queue is released to trap
any (and there shouldn't be any) use after the queue is freed.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The current problem seen is that the queue lock is actually in the
SCSI device structure, so when that structure is freed on device
release, we go boom if the queue tries to access the lock again.
The fix here is to move the lock from the scsi_device to the queue.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!