Add a function to update mc_disabled from switchdev attr
SWITCHDEV_ATTR_ID_BRIDGE_MC_DISABLED
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_port_orig_get returns the vport from the physical
port if needed, based on the original device.
This patch addresses the case where the original device is a bridge.
If it is vlan unaware bridge, it returns the matching vport. If it is vlan
aware bridge, there is no matching vport, and it returns the original port.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The decision whether to flood a multicast packet to a port dependent
on three flags: mc_disabled, mc_router_port, mc_flood.
If mc_disabled is on, the port will be flooded according to mc_flood,
otherwise, according to mc_router_port. To accomplish that, add those
flags into the mlxsw_sp_port struct and update the mc flood table
accordingly.
Update mc_router_port by switchdev attribute
SWITCHDEV_ATTR_ID_PORT_MC_ROUTER_PORT.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Break the bm (broadcast-multicast) into two tables, one for broadcast
(and link local multicast that behaves like bc) and one for unknown
multicasts.
Add a bool into mlxsw_sp_port named mc_flood that reflect the value this
port should have in the mc flood table (currently, always 1);
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is a per port flood update function only for the UC
table. Make the function more generic by changing the table type to be
an input.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the flood set function can't operate on only one table, but
sets both uc_flood and mb_flood together.
This patch creates a function that sets the flood state per table.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the device, a MID entry represents a group of local ports, which can
later be bound to a MDB entry.
The lookup of an existing MID entry is currently done using the provided
MC MAC address and VID, from the Linux bridge. However, this can result
in an incorrect reuse of the same MID index in different VLAN-unaware
bridges (same IP MC group and VID 0).
Fix this by performing the lookup based on FID instead of VID, which is
unique across different bridges.
Fixes: 3a49b4fde2 ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the number of resources is going to get much bigger, ease up the
addition by simly defining IDs. Convert the existing structure members
to a set array, one for validity, one for values. Introduce a set of
getters and setters for easy access.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, in order to offload a FIB entry to HW we use switchdev op.
However that has limits. Mainly in case we need to make the HW aware of
all route prefixes configured in kernel. HW needs to know those in order
to properly trap appropriate packets and pass the to kernel to do
the forwarding. Abort mechanism is now handled within the mlxsw driver.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use max lag and max ports in lag resources as the result of resource query
instead of using const to save them.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added on a bridge port we should use the existing unicast
flood configuration of the port instead of assuming it's enabled.
Fixes: 0293038e0c ("mlxsw: spectrum: Add support for flood control")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 14d39461b3 ("mlxsw: spectrum: Use per-FID struct for the
VLAN-aware bridge") I added a per-FID struct, which member ports can
take a reference on upon VLAN membership configuration.
However, sometimes only the VLAN flags (e.g. egress untagged) are
toggled without changing the VLAN membership. In these cases we
shouldn't take another reference on the FID.
Fixes: 14d39461b3 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now offload the learning configuration to the device and don't rely
on the driver to decide whether to learn the FDB record, so remove the
check.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we simply stored the learning configuration of a bridge
port in the driver and decided whether to learn a new FDB record based
on this value.
However, this is sub-optimal in cases where learning is disabled on the
bridge port, as the device repeatedly generates learning notifications
for the same record.
Instead, offload the learning configuration to the device, thereby
preventing it from generating notifications when learning is disabled.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to prevent the device from generating learning
notifications for a port that was configured with learning disabled.
Since learning configuration is done per {Port, VID} we need to apply
the port's learning configuration for any VID that is added to the
bridge port's VLAN filter list.
When a VID is added to the VLAN filter list of a VLAN-aware bridge port,
configure the {Port, VID} learning status according to the port's
configuration. When the VID is removed, disable learning for the {Port,
VID}.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing VLANs from the VLAN-aware bridge we shouldn't abort on the
first error, as we'll otherwise have resources that will never be freed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05978481e7 ("mlxsw: spectrum: Create PVID vPort before
registering netdevice") removed __mlxsw_sp_port_vlans_del() from the
init sequence of the driver, which forced it to be non-symmetric with
regards to __mlxsw_sp_port_vlans_add().
Make both functions symmetric as the constraint no longer exists.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now a learning session ended whenever the number of queried
records was zero. This turned out to be problematic in situations where
a large number of MACs (48K) had to be processed by the switch driver,
as RTNL mutex is held during the learning session.
Instead, limit the number of FDB records that can be processed in a
session to 64. This means that every time the device is queried for
learning notifications (currently, every 100ms), up to 64 records will
be processed by the switch driver.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before destroying the 802.1Q FID we should first remove the VID-to-FID
mapping. This makes mlxsw_sp_fid_destroy() symmetric with regards to
mlxsw_sp_fid_create().
Fixes: 14d39461b3 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After registering a netdevice it's possible for user space applications
to configure an IP address on it. From the driver's perspective, this
means a router interface (RIF) should be created for the PVID vPort.
Therefore, we must create the PVID vPort before registering the
netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with the previously introduced L3 interfaces, listen to 'inetaddr'
notifications sent for bridges devices configured on top of the port
netdevs and create / destroy router interfaces (RIFs) accordingly.
This also includes VLAN devices configured on top of the VLAN-aware
bridge.
The RIFs will be destroyed either when the last IP address is removed or
when the underlying FID is is destroyed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before introducing support for L3 interfaces on top of the VLAN-aware
bridge we need to add some missing infrastructure.
Such an interface can either be the bridge device itself or a VLAN
device on top of it. In the first case the router interface (RIF) is
associated with FID 1, which is created whenever the first port netdev
joins the bridge. We currently assume the default PVID is 1 and that
it's already created, as it seems reasonable. This can be extended in
the future.
However, in the second case it's entirely possible we've yet to create a
matching FID. This can happen if the VLAN device was configured before
making any bridge port member in the VLAN.
Prevent such ordering problems by using the VLAN device's CHANGEUPPER
event to configure the FID. Make the VLAN device hold a reference to the
FID and prevent it from being destroyed even if none of the port netdevs
is using it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we only supported bridged interfaces. Packets ingressing
through the switch ports were either classified to FIDs (in the case of
the VLAN-aware bridge) or vFIDs (in the case of VLAN-unaware bridges).
The packets were then forwarded according to the FDB. Routing was done
entirely in slowpath, by splitting the vFID range in two and using the
lower 0.5K vFIDs as dummy bridges that simply flooded all incoming
traffic to the CPU.
Instead, allow packets to be routed in the device by creating router
interfaces (RIFs) that will direct them to the router block.
Specifically, the RIFs introduced here are Sub-port RIFs used for VLAN
devices and port netdevs. Packets ingressing from the {Port / LAG ID, VID}
with which the RIF was programmed with will be assigned to a special
kind of FIDs called rFIDs and from there directed to the router.
Create a RIF whenever the first IPv4 address was programmed on a VLAN /
LAG / port netdev. Destroy it upon removal of the last IPv4 address.
Receive these notifications by registering for the 'inetaddr'
notification chain. A non-zero (10) priority is used for the
notification block, so that RIFs will be created before routes are
offloaded via FIB code.
Note that another trigger for RIF destruction are CHANGEUPPER
notifications causing the underlying FID's reference count to go down to
zero. This can happen, for example, when a VLAN netdev with an IP address
is put under bridge. While this configuration doesn't make sense it does
cause the device and the kernel to get out of sync when the netdev is
unbridged. We intend to address this in the future, hopefully in current
cycle.
Finally, Remove the lower 0.5K vFIDs, as they are deprecated by the RIFs,
which will trap packets according to their DIP.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are just about to introduce router interfaces (RIFs), but before that
we need to be able update the device with the correct RIF attributes
whenever they change for the netdev the RIF is backing. Two such
attributes are MTU and MAC.
The MAC is used both to set the source MAC of packets egressing from the
RIF and also to program an FDB rule that will direct packets to the
router block.
Use the existing netdevice notification block and respond to CHANGEADDR
and CHANGEMTU accordingly. Store both attributes in the RIF struct
in case we need to revert to old attributes following a failed update.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement ipv4 FIB entries addition and removal. Initially, we support
local and broadcast routes using "ip2me" trap action.
Also, unicast routes without nexthop are supported using "local" action.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port isn't bridged it is still possible to invoke switchdev ops and
configure the device's VLAN filters.
However, this will require us to use different Router InterFaces (RIFs)
for the same netdev, instead of one per-netdev as with any other
configuration.
Taking the above into account and the fact that this functionality is
questionable with regards to the device's normal use-case, remove it and
instead return an error.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For debug purposes, it's useful to know the order in which the driver
responds to changes in the topology of its upper devices.
Add debug prints to signal these events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FDB entries are learned using {Port / LAG ID, FID} and therefore should
be flushed whenever a port (vPort) leaves its FID (vFID).
However, when the bridge port is a LAG device (or a VLAN device on top),
then FDB flushing is conditional. Ports removed from such LAG
configurations must not trigger flushing, as other ports might still be
members in the LAG and therefore the bridge port is still active.
The decision whether to flush or not was previously computed in the
netdevice notification block, but in order to flush the entries when a
port leaves its FID this decision should be computed there.
Strip the notification block from this logic and instead move it to one
FDB flushing function that is invoked from both the FID / vFID leave
functions.
When port isn't member in LAG, FDB flushing should always occur.
Otherwise, it should occur only when the last port (vPort) member in the
LAG leaves the FID (vFID).
This will allow us - in the next patch - to simplify the cleanup code
paths that are hit whenever the topology above the port netdevs changes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all vPorts will have FIDs assigned to them, so make sure functions
first test for FID presence.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As previously explained, not all vPorts will be assigned FIDs, so instead
of returning the FID index of a vPort, return a pointer to its FID
struct. This will allow us to know whether it's legal to access the
vPort's FID parameters such as index and device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a very similar way to the vFIDs, make the first 4K FIDs - used in the
VLAN-aware bridge - use the new FID struct.
Upon first use of the FID by any of the ports do the following:
1) Create the FID
2) Setup a matching flooding entry
3) Create a mapping for the FID
Unlike vFIDs, upon creation of a FID we always create a global
VID-to-FID mapping, so that ports without upper vPorts can use it
instead of creating an explicit {Port, VID} to FID mapping.
When a port leaves a FID the reverse is performed. Whenever the FID's
reference count reaches zero the FID is deleted along with the global
mapping.
The per-FID struct will later allow us to configure L3 interfaces on top
of the VLAN-aware bridge.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we had a dedicated struct only for vFIDs, but before
introducing support for L3 interfaces we need to make it generic and
use it for all three types of FIDs:
1) FIDs - 0..4K-1, used for the VLAN-aware bridge
2) vFIDs - 4K..15K-1, used for VLAN-unaware bridges
3) rFIDs - 15K..16K-1, used to direct traffic to / from the router in
the device. Will be introduced later in the series.
The three types of L3 interfaces - Router InterFaces, RIFs - that will
be introduced correspond to the three types of FIDs and are configured
using them. Therefore, we'll need to store the links between them as
well as a reference count on the underlying FID, so that the
corresponding RIF will be destroyed when it reaches zero.
Note that the lower 0.5K vFIDs are currently used for for non-bridged
netdevs, so that traffic could be flooded to the CPU port. However, when
rFIDs will be introduced we'll no longer need these and they too will be
used for VLAN-unaware bridges.
Make the vFID struct generic by renaming it and some of its fields. FIDs
will be converted to use it later in the series.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use a FID index instead of vFID and ease the transition towards a
generic FID struct.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all call sites 'only_uc' is set to false, so strip it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
When we fail to set the flooding configuration for the broadcast and
unregistered multicast traffic, we should revert the flooding
configuration of the unknown unicast traffic.
Fixes: 0293038e0c ("mlxsw: spectrum: Add support for flood control")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up patch is going to need to use delayed work as well and
frequently. The FDB notification processing is already using that and
also quite frequently. It makes sense to create separate workqueue just
for mlxsw driver in this case and do not pollute system_wq.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c62987bbd8 ("bridge: push bridge setting ageing_time down to
switchdev") added a check for minimum and maximum ageing time, but this
breaks existing behaviour where one can set ageing time to 0 for a
non-learning bridge.
Push this check down to the driver and allow the check in the bridge
layer to be removed. Currently ageing time 0 is refused by the driver,
but we can later add support for this functionality.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PVID is toggled off on a port member in a VLAN filtering bridge or
the PVID VLAN is deleted, make the port drop untagged packets. Reverse
the operation when PVID is toggled back on.
Set the PVID back to the default (1), when leaving the bridge so that
untagged traffic will be directed to the CPU.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When switchdev drivers process FDB notifications from the underlying
device they resolve the netdev to which the entry points to and notify
the bridge using the switchdev notifier.
However, since the RTNL mutex is not held there is nothing preventing
the netdev from disappearing in the middle, which will cause
br_switchdev_event() to dereference a non-existing netdev.
Make switchdev drivers hold the lock at the beginning of the
notification processing session and release it once it ends, after
notifying the bridge.
Also, remove switchdev_mutex and fdb_lock, as they are no longer needed
when RTNL mutex is held.
Fixes: 03bf0c2812 ("switchdev: introduce switchdev notifier")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dumping the FDB we can't compare the actual pointers of the ports
structs, as it's possible the struct represents a vPort instead of the
underlying physical port.
Solve this by comparing the local port number instead, as it's shared
between the physical ports and all the vPorts on top of him.
Fixes: 54a732018d ("mlxsw: spectrum: Adjust switchdev ops for VLAN devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAG FDB records can only point to LAG devices or VLAN devices configured
on top of them. Therefore, when dumping the FDB we shouldn't associate
these records with the underlying physical ports.
Fixes: 8a1ab5d766 ("mlxsw: spectrum: Implement FDB add/remove/dump for LAG")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LAG FDB entries pointing to VLAN devices should be reported to the
bridge with the matching VLAN device and not the underlying LAG device.
Fixes: aac78a4408 ("mlxsw: spectrum: Adjust FDB notifications for VLAN devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dumping the hardware FDB we should report entries pointing to VLAN
devices with VLAN 0, as packets coming into the bridge are untagged.
Likewise, pass FDB_{ADD,DEL} notifications with VLAN 0 for these
devices.
Fixes: 54a732018d ("mlxsw: spectrum: Adjust switchdev ops for VLAN devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disable learning on bridge port we should still update the
software bridge's FDB when entry pointing to this bridge port is
aged-out. We can otherwise have an inconsistency between software and
hardware tables.
Fixes: 8a1ab5d766 ("mlxsw: spectrum: Implement FDB add/remove/dump for LAG")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is put into LISTENING state it shouldn't populate the FDB, so
set the port's STP state in hardware to DISCARDING instead of LEARNING.
It will therefore keep listening to BPDU packets, but discard other
non-control packets and won't perform any learning.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When STP state is set to DISABLED the port is assumed to be inactive, but
currently we forward packets ingressing through it.
Instead, set the port's STP state in hardware to DISCARDING, which means
it doesn't forward packets or perform any learning, but it does trap
control packets. However, these packets will be dropped by bridge code,
which results in the expected behavior.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible for a user to remove a port from a LAG device, while the
LAG device or VLAN devices on top of it are bridged. In these cases,
bridge's teardown sequence is never issued, so we need to take care of
it ourselves.
When LAG's unlinking event is received by port netdev:
1) Traverse its vPorts list and make those member in a bridge leave it.
They will be deleted later by LAG code.
2) Make the port netdev itself leave its bridge if member in one.
Fixes: 0d65fc1304 ("mlxsw: spectrum: Implement LAG port join/leave")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
