Driver sends update-SVID ramrod in the MFW notification path.
If there is a pending ramrod, driver doesn't retry the command
and storm firmware will never be updated with the SVID value.
The patch adds changes to send update-svid ramrod in process context with
retry/poll flags set.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There will be only one PHC clock per port. PTP should be enabled only on
one PF per port. The change enables PTP functionality on the PF that
initializes the port. The change is useful in multi-function modes e.g.,
NPAR where a port can have more than one PF.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlans are not getting removed when drivers are unloaded. The recent storm
firmware versions had added safeguards against re-configuring an already
configured vlan. As a result, PF inner reload flows (e.g., mtu change)
might trigger an assertion.
This change is going to remove vlans (same as we do for MACs) when doing
a chip cleanup during unload.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some customer setups it was observed that shmem contains a non-zero fip
MAC for 57711 which would lead to enabling of SW FCoE.
Add a software workaround to clear the bad fip mac address if no FCoE
connections are supported.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function hso_probe reads if_num from the USB device (as an u8) and uses
it without a length check to index an array, resulting in an OOB memory read
in hso_probe or hso_get_config_data.
Add a length check for both locations and updated hso_probe to bail on
error.
This issue has been assigned CVE-2018-19985.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_DEBUG_SHIRQ is enabled __free_irq() intentionally fires
a spurious interrupt. This interrupt causes a crash because
tp->dev->phydev is NULL at that time.
Fixes: 38caff5a44 ("r8169: handle all interrupt events in the hard irq handler")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stefan Schmidt says:
====================
pull-request: ieee802154 for net 2018-12-11
An update from ieee802154 for your *net* tree.
Just two more fixes for ieee802154 dribver before the final 4.20 release.
Alexander Aring fixes a problem in the nested parsing code of the
hwsim driver interface.
A fix for a potential overflow in the ca8210 driver by Yue Habing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warning this:
drivers/net/ieee802154/ca8210.c:730:10: warning:
comparison is always false due to limited range of data type [-Wtype-limits]
'len' is u8 type, we get it from buf[1] adding 2, which can overflow.
This patch change the type of 'len' to unsigned int to avoid this,also fix
the gcc warning.
Fixes: ded845a781 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Previously we did not ensure tcp flags have a place to be stored
when using IPv6. We correct this by including IPv6 key layer when
we match tcp flags and the IPv6 key layer has not been included
already.
Fixes: 07e1671cfc ("nfp: flower: refactor shared ip header in match offload")
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CP rings are accounted differently on the new 57500 chips. There
must be enough CP rings for the sum of RX and TX rings on the new
chips. The current logic may be over-estimating the RX and TX rings.
The output parameter max_cp should be the maximum NQs capped by
MSIX vectors available for networking in the context of 57500 chips.
The existing code which uses CMPL rings capped by the MSIX vectors
works most of the time but is not always correct.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new 57500 chips have introduced the NQ structure in addition to
the existing CP rings in all chips. We need to introduce a new
bnxt_nq_rings_in_use(). On legacy chips, the 2 functions are the
same and one will just call the other. On the new chips, they
refer to the 2 separate ring structures. The new function is now
called to determine the resource (NQ or CP rings) associated with
MSIX that are in use.
On 57500 chips, the RDMA driver does not use the CP rings so
we don't need to do the subtraction adjustment.
Fixes: 41e8d79837 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new 57500 chips use 1 NQ per MSIX vector, whereas legacy chips use
1 CP ring per MSIX vector. To better unify this, add a resv_irqs
field to struct bnxt_hw_resc. On legacy chips, we initialize resv_irqs
with resv_cp_rings. On new chips, we initialize it with the allocated
MSIX resources.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recent changes to support the 57500 devices have created this
regression. The bnxt_hwrm_queue_qportcfg() call was moved to be
called earlier before the RDMA support was determined, causing
the CoS queues configuration to be set before knowing whether RDMA
was supported or not. Fix it by moving it to the right place right
after RDMA support is determined.
Fixes: 98f04cf0f1 ("bnxt_en: Check context memory requirements from firmware.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx_ppp and tx_ppp can be set between 0 and 255, so don't clamp to 1.
Fixes: 6e8814ceb7 ("net/mlx4_en: Fix mixed PFC and Global pause user control requests")
Signed-off-by: Tarick Bedeir <tarick@google.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 624ca9c33c.
This commit is completely bogus. The STACR register has two formats, old
and new, depending on the version of the IP block used. There's a pair of
device-tree properties that can be used to specify the format used:
has-inverted-stacr-oc
has-new-stacr-staopc
What this commit did was to change the bit definition used with the old
parts to match the new parts. This of course breaks the driver on all
the old ones.
Instead, the author should have set the appropriate properties in the
device-tree for the variant used on his board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deleting a VLAN device using an ioctl the netdev is unregistered
before the VLAN filter is updated via ndo_vlan_rx_kill_vid(). It can
lead to a use-after-free in mlxsw in case the VLAN device is deleted
while being enslaved to a bridge.
The reason for the above is that when mlxsw receives the CHANGEUPPER
event, it wrongly assumes that the VLAN device is no longer its upper
and thus destroys the internal representation of the bridge port despite
the reference count being non-zero.
Fix this by checking if the VLAN device is our upper using its real
device. In net-next I'm going to remove this trick and instead make
mlxsw completely agnostic to the order of the events.
Fixes: c57529e1d5 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRE decap offload is configured when local routes prefix correspond to the
local address of one of the offloaded GRE tunnels. The matching check was
found to be too strict, such that for a flat GRE configuration, in which
the overlay and underlay traffic share the same non-default VRF, decap flow
was not offloaded.
Relax the check for decap flow offloading. A match occurs if the local
address of the tunnel matches the local route address while both share the
same VRF table.
Fixes: 4607f6d269 ("mlxsw: spectrum_router: Support IPv4 underlay decap")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It should never be possible for a user to set a VNI on a FID in case one
is already set. The driver therefore returns an error, but fails to drop
the reference count taken earlier when calling
mlxsw_sp_fid_8021d_lookup().
Drop the reference when this unlikely error is hit.
Fixes: 1c30d1836a ("mlxsw: spectrum: Enable VxLAN enslavement to bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible to trigger a warning in mlxsw in case a flood entry which
mlxsw is not aware of is deleted from the VxLAN device. This is because
mlxsw expects to find a singly linked list where the flood entry is
present in.
Fix by removing these warnings for now.
Will re-add them in the next release after we teach mlxsw to ask for a
dump of FDB entries from the VxLAN device, once it is enslaved to a
bridge mlxsw cares about.
Fixes: 6e6030bd54 ("mlxsw: spectrum_nve: Implement common NVE core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* hwsim
* AP mode (client powersave related)
* CSA/FTM interaction
* a busy loop in IE handling
* and similar
-----BEGIN PGP SIGNATURE-----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=MDbC
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-12-05' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg:
====================
As it's been a while, we have various fixes for
* hwsim
* AP mode (client powersave related)
* CSA/FTM interaction
* a busy loop in IE handling
* and similar
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The .validate phylink callback should empty the supported bitmap when
the interface mode is invalid.
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_phylink_validate() relies on the interface field of
phylink_link_state to determine valid link modes. However, when called
from phylink_sfp_module_insert() this field in not initialized. The
default switch case then excludes 10G link modes. This allows 10G SFP
modules that are detected correctly to be configured at max rate of
2.5G.
Catch the uninitialized PHY mode case, and allow 10G rates.
Fixes: d97c9f4ab0 ("net: mvpp2: 1000baseX support")
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
After getting a reference to the platform device's of_node the probe
function ends up calling of_find_matching_node() using the node as an
argument. The function takes care of decreasing the refcount on it. We
are then incorrectly decreasing the refcount on that node again.
This patch removes the unwarranted call to of_node_put().
Fixes: 414fd46e77 ("fsl/fman: Add FMan support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts:
ef1b5bf506 ("net: phy: Fix not to call phy_resume() if PHY is not attached")
8c85f4b812 ("net: phy: micrel: add toggling phy reset if PHY is not attached")
Andrew Lunn informs me that there are alternative efforts
underway to fix this more properly.
Signed-off-by: David S. Miller <davem@davemloft.net>
MLX4_EN depends on NETDEVICES, ETHERNET and INET Kconfigs.
Make sure they are listed in MLX4_EN Kconfig dependencies.
This fixes the following build break:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: ‘struct iphdr’ declared inside parameter list [enabled by default]
struct iphdr *iph)
^
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/ethernet/mellanox/mlx4/en_rx.c: In function ‘get_fixed_ipv4_csum’:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:586:20: error: dereferencing pointer to incomplete type
_u8 ipproto = iph->protocol;
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC driver minimal MTU size shall be set to ETH_MIN_MTU, as defined in
the RFC791 and in the network stack. Remove old mlx4_en only define for
it, which was set to wrong value.
Fixes: b80f71f581 ("ethernet/mellanox: use core min/max MTU checking")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable hardware level MAC learning because it breaks station roaming.
When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.
Signed-off-by: Anderson Luiz Alves <alacn1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A MAC address must be unique among all the macvlan devices with the same
lower device. The only exception is the passthru [sic] mode,
which shares the lower device address.
When duplicate addresses are detected, EBUSY is returned when bringing
the interface up:
# ip link add macvlan0 link eth0 type macvlan
# read addr </sys/class/net/eth0/address
# ip link set macvlan0 address $addr
# ip link set macvlan0 up
RTNETLINK answers: Device or resource busy
Use correct error code which is EADDRINUSE, and do the check also
earlier, on address change:
# ip link set macvlan0 address $addr
RTNETLINK answers: Address already in use
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a5681e20b5 ("net/ibmnvic: Fix deadlock problem
in reset") made the change to hold the RTNL lock during
driver reset but still calls netdev_notify_peers, which
results in a deadlock. Instead, use call_netdevice_notifiers,
which is functionally the same except that it does not
take the RTNL lock again.
Fixes: a5681e20b5 ("net/ibmnvic: Fix deadlock problem in reset")
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds toggling phy reset if PHY is not attached. Otherwise,
some boards (e.g. R-Car H3 Salvator-XS) cannot link up correctly if
we do the following method:
1) Kernel boots by using initramfs.
--> No open the nic, so phy_device_register() and phy_probe()
deasserts the reset.
2) Kernel enters the suspend.
--> So, keep the reset signal as deassert.
--> On R-Car Salvator-XS board, unfortunately, the board power is
turned off.
3) Kernel returns from suspend.
4) ifconfig eth0 up
--> Then, since edge signal of the reset doesn't happen,
it cannot link up.
5) ifconfig eth0 down
6) ifconfig eth0 up
--> In this case, it can link up.
Reported-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue that mdio_bus_phy_resume() doesn't call
phy_resume() if the PHY is not attached.
Fixes: 803dd9c77a ("net: phy: avoid suspending twice a PHY")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
The commit marked as fixed didn't do anything wrong, it just copied
existing functionality to the helper which is being fixed now.
Fixes: f3a6bd393c ("phylib: Add phy_set_max_speed helper")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a off-by-one mistake in nla_parse_nested() functions of
mac802154_hwsim driver. I had to enabled stack protector so I was able
to reproduce it.
Reference: https://github.com/linux-wpan/wpan-tools/issues/17
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
It's not supported right now (the goal of the initial patch was to support
'ip link del' only).
Before the patch:
$ ip link add foo type tun
[ 239.632660] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[snip]
[ 239.636410] RIP: 0010:register_netdevice+0x8e/0x3a0
This panic occurs because dev->netdev_ops is not set by tun_setup(). But to
have something usable, it will require more than just setting
netdev_ops.
Fixes: f019a7a594 ("tun: Implement ip link del tunXXX")
CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We copy vnet header unconditionally in page_to_skb() this is wrong
since XDP may modify the packet data. So let's keep a zeroed vnet
header for not confusing the conversion between vnet header and skb
metadata.
In the future, we should able to detect whether or not the packet was
modified and keep using the vnet header when packet was not touched.
Fixes: f600b69050 ("virtio_net: Add XDP support")
Reported-by: Pavel Popa <pashinho1990@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function lio_vf_rep_packet_sent_callback releases the occupation of
sc via octeon_free_soft_command. sc should not be used after that.
Unfortunately, sc->iq_no is read. To fix this, the patch stores sc->iq_no
into a local variable before releasing sc and then uses the local variable
instead of sc->iq_no.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP header is not necessarily located right after struct ethhdr,
there could be multiple 802.1Q headers in between, this is why
we call __vlan_get_protocol().
Fixes: fe1dc06999 ("net/mlx5e: don't set CHECKSUM_COMPLETE on SCTP packets")
Cc: Alaa Hleihel <alaa@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For flow offload adds, if the rhash insert code fails, the flow will still
have been offloaded but the reference to it in the driver freed.
Re-order the offload setup calls to ensure that a flow will only be written
to FW if a kernel reference is held and stored in the rhashtable. Remove
this hashtable entry if the offload fails.
Fixes: c01d0efa51 ("nfp: flower: use rhashtable for flow caching")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling nfp_compile_flow_metadata both assigns a stats context and
increments a ref counter on (or allocates) a mask id table entry. These
are released by the nfp_modify_flow_metadata call on flow deletion,
however, if a flow add fails after metadata is set then the flow entry
will be deleted but the metadata assignments leaked.
Add an error path to the flow add offload function to ensure allocated
metadata is released in the event of an offload fail.
Fixes: 81f3ddf254 ("nfp: add control message passing capabilities to flower offloads")
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously when unbinding a slave the 802.3ad implementation only told
partner that the port is not suitable for aggregation by setting the port
aggregation state from aggregatable to individual. This is not enough. If the
physical layer still stays up and we only unbinded this port from the bond there
is nothing in the aggregation status alone to prevent the partner from sending
traffic towards us. To ensure that the partner doesn't consider this
port at all anymore we should also disable collecting and distributing to
signal that this actor is going away. Also clear AD_STATE_SYNCHRONIZATION to
ensure partner exits collecting + distributing state.
I have tested this behaviour againts Arista EOS switches with mlx5 cards
(physical link stays up even when interface is down) and simulated
the same situation virtually Linux <-> Linux with two network namespaces
running two veth device pairs. In both cases setting aggregation to
individual doesn't alone prevent traffic from being to sent towards this
port given that the link stays up in partners end. Partner still keeps
it's end in collecting + distributing state and continues until timeout is
reached. In most cases this means we are losing the traffic partner sends
towards our port while we wait for timeout. This is most visible with slow
periodic time (LACP rate slow).
Other open source implementations like Open VSwitch and libreswitch, and
vendor implementations like Arista EOS, seem to disable collecting +
distributing to when doing similar port disabling/detaching/removing change.
With this patch kernel implementation would behave the same way and ensure
partner doesn't consider our actor viable anymore.
Signed-off-by: Toni Peltonen <peltzi@peltzi.fi>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last set of csum offload fixes had a leak:
Checksum enabled status bits from rx descriptor were incorrectly
interpreted. Consequently all the other valid logic worked on zero bits.
That caused rx checksum offloads never to trigger.
Tested by dumping rx descriptors and validating resulting csum_level.
Reported-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Dmitry Bogdanov <dmitry.bogdanov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Fixes: ad703c2b91 ("net: aquantia: invalid checksumm offload implementation")
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling mistake in the oct_stats_strings array, fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting up and tearing down debugfs is current unbalanced, as seen by
this error during resume from suspend:
[ 752.134067] dwc-eth-dwmac 2490000.ethernet eth0: ERROR failed to create debugfs directory
[ 752.134347] dwc-eth-dwmac 2490000.ethernet eth0: stmmac_hw_setup: failed debugFS registration
The imbalance happens because the driver creates the debugfs hierarchy
when the device is opened and tears it down when the device is closed.
There's little gain in that, and it could be argued that it is even
surprising because it's not usually done for other devices. Fix the
imbalance by moving the debugfs creation and teardown to the driver's
->probe() and ->remove() implementations instead.
Note that the ring descriptors cannot be read while the interface is
down, so make sure to return an empty file when the descriptors_status
debugfs file is read.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link modes that sfp_parse_support() detects are stored in the
'modes' bitmap. There is no reason to make an exception for 1000Base-PX
or 1000Base-BX10.
Fixes: 03145864bd ("sfp: support 1G BiDi (eg, FiberStore SFP-GE-BX) modules")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing MODULE_AUTHOR of ave driver and an entry to MAINTAINERS.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 26a4676faa ("arm64: mm: define NET_IP_ALIGN to 0"),
AVE controller affects this modification because the controller forces
to ignore lower 2bits of buffer start address, and make 2-byte headroom,
that is, data reception starts from (buffer + 2).
This patch defines AVE_FRAME_HEADROOM macro as hardware-specific value,
and replaces NET_IP_ALIGN with it.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
