In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For packets with computed IP/TCP/UDP checksum there is no need to tell
hardware to recompute it. For such kind of packets hardware expects the
packet to be at least 64 bytes and FCS to be computed.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move checksum clearing outside of spinlock. The SKB is protected by
networking lock (HARD_TX_LOCK()).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use netdev_tx_t return type for ndo_start_xmit function of macb driver.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GEM version in ZynqMP and most versions greater than r1p07 supports
TX and RX BD prefetch. The number of BDs that can be prefetched is a
HW configurable parameter. For ZynqMP, this parameter is 4.
When GEM DMA is accessing the last BD in the ring, even before the
BD is processed and the WRAP bit is noticed, it will have prefetched
BDs outside the BD ring. These will not be processed but it is
necessary to have accessible memory after the last BD. Especially
in cases where SMMU is used, memory locations immediately after the
last BD may not have translation tables triggering HRESP errors. Hence
always allocate extra BDs to accommodate for prefetch.
The value of tx/rx bd prefetch for any given SoC version is:
2 ^ (corresponding field in design config 10 register).
(value of this field >= 1)
Added a capability flag so that older IP versions that do not have
DCFG10 or this prefetch capability are not affected.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rx ring is allocated for all queues in macb_alloc_consistent.
Free the same for all queues instead of just Q0.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vendor guard Kconfig symbols for Cadence and Packet Engines use a
"NET_" prefix, while all other vendor guards use a "NET_VENDOR_"
prefix. Hence make them consistent with the rest, and add the missing
trailing "S" for Packet Engines while at it.
As these options don't directly affect the kernel build, and default to
"y", this change has no impact on kernels built with existing
(def)configs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb driver currently crashes on at91rm9200 with the following trace:
Unable to handle kernel NULL pointer dereference at virtual address 00000014
[...]
[<c031da44>] (macb_rx_desc) from [<c031f2bc>] (at91ether_open+0x2e8/0x3f8)
[<c031f2bc>] (at91ether_open) from [<c041e8d8>] (__dev_open+0x120/0x13c)
[<c041e8d8>] (__dev_open) from [<c041ec08>] (__dev_change_flags+0x17c/0x1a8)
[<c041ec08>] (__dev_change_flags) from [<c041ec4c>] (dev_change_flags+0x18/0x4c)
[<c041ec4c>] (dev_change_flags) from [<c07a5f4c>] (ip_auto_config+0x220/0x10b0)
[<c07a5f4c>] (ip_auto_config) from [<c000a4fc>] (do_one_initcall+0x78/0x18c)
[<c000a4fc>] (do_one_initcall) from [<c0783e50>] (kernel_init_freeable+0x184/0x1c4)
[<c0783e50>] (kernel_init_freeable) from [<c0574d70>] (kernel_init+0x8/0xe8)
[<c0574d70>] (kernel_init) from [<c00090e0>] (ret_from_fork+0x14/0x34)
Solve that by initializing bp->queues[0].bp in at91ether_init (as is done
in macb_init).
Fixes: ae1f2a56d2 ("net: macb: Added support for many RX queues")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When delta passed to gem_ptp_adjtime is negative, the sign is
maintained in the ns_to_timespec64 conversion. Hence timespec_add
should be used directly. timespec_sub will just subtract the negative
value thus increasing the time difference.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches noted that we have a few source files that for some
inexplicable reason (read: I'm too lazy to even go look at the history)
are marked executable:
drivers/gpu/drm/amd/amdgpu/vce_v4_0.c
drivers/net/ethernet/cadence/macb_ptp.c
A simple git command line to show executable C/asm/header files is this:
git ls-files -s '*.[chsS]' | grep '^100755'
and then you can fix them up with scripting by just feeding that output
into:
| cut -f2 | xargs chmod -x
and commit it.
Which is exactly what this commit does.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Call of_get_nvmem_mac_address() to fetch the MAC address from an nvmem
cell, if one is provided in the device tree. This allows the address to
be stored in an I2C EEPROM device for example.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This optional binding (as described in the ethernet DT bindings doc)
directs the netdev to the phydev to use. This is useful for a phy
chip that has >1 phy in it, and two netdevs are using the same phy
chip (i.e. the second mac's phy lives on the first mac's MDIO bus)
The devicetree snippet would look something like this:
ethernet@feedf00d {
...
phy-handle = <&phy0> // the first netdev is physically wired to phy0
...
phy0: phy@0 {
...
reg = <0x0> // MDIO address 0
...
}
phy1: phy@1 {
...
reg = <0x1> // MDIO address 1
...
}
...
}
ethernet@deadbeef {
...
phy-handle = <&phy1> // tells the driver to use phy1 on the
// first mac's mdio bus (it's wired thusly)
...
}
The work done to add the phy_node in the first place (dacdbb4dfc:
"net: macb: add fixed-link node support") will consume the
device_node (if found).
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In phy_device's general probe, this device will already be set for
phy register polling, rendering this code redundant.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb mii setup (mii_probe() and mii_init()) previously was
somewhat interspersed, likely a result of organic growth and hacking.
This change moves mii bus registration into mii_init and probing the
bus for devices into mii_probe.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle HRESP error by doing a SW reset of RX and TX and
re-initializing the descriptors, RX and TX queue pointers.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the rx_fs_lock is no longer held across allocation, it's safe
to use GFP_KERNEL for allocating new entries.
This reverts commit 81da3bf6e3 ("net: macb: change GFP_KERNEL to
GFP_ATOMIC").
Cc: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ae8223de3d ("net: macb: Added support for RX filtering")
introduces a lock, rx_fs_lock which is intended to protect the list of
rx_flow items and synchronize access to the hardware rx filtering
registers.
However, the region protected by this lock is overscoped, unnecessarily
including things like slab allocation. Reduce this lock scope to only
include operations which must be performed atomically: list traversal,
addition, and removal, and hitting the macb filtering registers.
This fixes the use of kmalloc w/ GFP_KERNEL in atomic context.
Fixes: ae8223de3d ("net: macb: Added support for RX filtering")
Cc: Rafal Ozieblo <rafalo@cadence.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The list_for_each_entry() macro already handles the case where the list
is empty (by not executing the loop body). It's not necessary to handle
this case specially, so stop doing so.
Cc: Rafal Ozieblo <rafalo@cadence.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the phylib now being aware of the "reset-gpios" PHY node property,
there should be no need to frob the PHY reset in this driver anymore...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function gem_add_flow_filter called on line 2958 inside lock on line 2949
but uses GFP_KERNEL
Generated by: scripts/coccinelle/locks/call_kern.cocci
Fixes: ae8223de3d ("net: macb: Added support for RX filtering")
CC: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows filtering received packets to different
hardware queues (aka ntuple).
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To be able for packet reception on different RX queues some
configuration has to be performed. This patch checks how many
hardware queue does GEM support and initializes them.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the call of_node_put(bp->phy_node) to all associated error
paths for memory clean up.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We add the call of_phy_deregister_fixed_link to all associated
error paths for memory clean up.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable work_done is set to zero and this value is never read, instead
it is set to another value a few statements later. Remove the redundant
assignment. Cleans up clang warning:
drivers/net/ethernet/cadence/macb_main.c:1221:2: warning: Value stored
to 'work_done' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Alexander Dahl <ada@thorsis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
@match disable optional_qualifier@
identifier s;
@@
static struct ptp_clock_info s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
position ref.p;
identifier match.s,f,c;
expression e;
@@
(
e = s@p
|
e = s@p.f
|
c(...,s@p.f,...)
|
c(...,s@p,...)
)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct ptp_clock_info s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
791 336 0 1127 467 net/ethernet/cadence/macb_pci.o
File size After adding 'const':
text data bss dec hex filename
855 272 0 1127 467 net/ethernet/cadence/macb_pci.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per the SAMA5D3 device specification it supports Jumbo frames.
But the suggested flag and length of bytes it supports was not updated
in this driver config_structure.
The maximum jumbo frames the device supports :
10240 bytes as per the device spec.
While changing the MTU value greater than 1500, it threw error:
sudo ifconfig eth1 mtu 9000
SIOCSIFMTU: Invalid argument
Add this support to driver so that it works as expected and designed.
Signed-off-by: vishnuvardhan <vardhanraj4143@gmail.com>
[nicolas.ferre@microchip.com: modify slightly commit msg]
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When macro MACB_EXT_DESC is defined we end up with two identical
return statements and just one is sufficient. Remove the extra
return.
Detected by CoverityScan, CID#1449361 ("Structurally dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is based on original Harini's patch and Andrei's patch,
implemented in a separate file to ease the review/maintanance
and integration with other platforms.
This driver supports GEM-GXL:
- Register ptp clock framework
- Initialize PTP related registers
- HW time stamp on the PTP Ethernet packets are received using the
SO_TIMESTAMPING API. Time stamps are obtained from the dma buffer
descriptors
- add macb_ptp to compilation chain
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case that macb is compiled as a module, macb.c has been renamed to
macb_main.c to avoid naming confusion in Makefile.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for PTP timestamps in
DMA buffer descriptors. It checks capability at runtime
and uses appropriate buffer descriptor.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the MACB is directly connected to a
non-mdio PHY/device, it should be possible to provide
a fixed link configuration in the DT.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 83a77e9ec4, the phydev irq is explicitly set to PHY_POLL when
there is no pdata. It doesn't work on DT enabled platforms because the
phydev irq is already set by libphy before.
Fixes: 83a77e9ec4 ("net: macb: Added PCI wrapper for Platform Driver.")
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using a private copy of struct net_device_stats in struct
macb, use stats from struct net_device.
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that %z is standartised in C99 there is no reason to support %Z.
Unlike %L it doesn't even make format strings smaller.
Use BUILD_BUG_ON in a couple ATM drivers.
In case anyone didn't notice lib/vsprintf.o is about half of SLUB which
is in my opinion is quite an achievement. Hopefully this patch inspires
someone else to trim vsprintf.c more.
Link: http://lkml.kernel.org/r/20170103230126.GA30170@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/net/ethernet/cadence/macb.h:862:33: sparse: expected ; at end of declaration
drivers/net/ethernet/cadence/macb.h:862:33: sparse: Expected } at end of struct-union-enum-specifier
drivers/net/ethernet/cadence/macb.h:862:33: sparse: got phy_interface
drivers/net/ethernet/cadence/macb.h:877:1: sparse: Expected ; at the end of type declaration
drivers/net/ethernet/cadence/macb.h:877:1: sparse: got }
In file included from drivers/net/ethernet/cadence/macb_pci.c:29:0:
drivers/net/ethernet/cadence/macb.h:862:2: error: unknown type name 'phy_interface_t'
phy_interface_t phy_interface;
^~~~~~~~~~~~~~~
Add linux/phy.h to macb.h
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for 32 bit GEM in
64 bit system. It checks capability at runtime
and uses appropriate buffer descriptor.
Signed-off-by: Rafal Ozieblo <rafalo@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does the following:
- MACB/GEM-PTP interface
- registers and bitfields for TSU
- capability flags to enable PTP per platform basis
Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed function calls of resource allocation to new API. Changed way
of setting DMA mask. Removed unnecessary sanity check.
This patch is sent in regard to recently applied patch
Commit 83a77e9ec4
net: macb: Added PCI wrapper for Platform Driver.
Signed-off-by: Bartosz Folta <bfolta@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are hardware PCI implementations of Cadence GEM network
controller. This patch will allow to use such hardware with reuse of
existing Platform Driver.
Signed-off-by: Bartosz Folta <bfolta@cadence.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple conflicts resolved here:
1) In the MACB driver, a bug fix to properly initialize the
RX tail pointer properly overlapped with some changes
to support variable sized rings.
2) In XGBE we had a "CONFIG_PM" --> "CONFIG_PM_SLEEP" fix
overlapping with a reorganization of the driver to support
ACPI, OF, as well as PCI variants of the chip.
3) In 'net' we had several probe error path bug fixes to the
stmmac driver, meanwhile a lot of this code was cleaned up
and reorganized in 'net-next'.
4) The cls_flower classifier obtained a helper function in
'net-next' called __fl_delete() and this overlapped with
Daniel Borkamann's bug fix to use RCU for object destruction
in 'net'. It also overlapped with Jiri's change to guard
the rhashtable_remove_fast() call with a check against
tc_skip_sw().
5) In mlx4, a revert bug fix in 'net' overlapped with some
unrelated changes in 'net-next'.
6) In geneve, a stale header pointer after pskb_expand_head()
bug fix in 'net' overlapped with a large reorganization of
the same code in 'net-next'. Since the 'net-next' code no
longer had the bug in question, there was nothing to do
other than to simply take the 'net-next' hunks.
Signed-off-by: David S. Miller <davem@davemloft.net>
When a hardware issue happened as described by inline comments, the register
write pattern looks like the following:
<write ~MACB_BIT(RE)>
+ wmb();
<write MACB_BIT(RE)>
There might be a memory barrier between these two write operations, so add wmb
to ensure an flip from 0 to 1 for NCR.
Signed-off-by: Zumeng Chen <zumeng.chen@windriver.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On macb only (not gem), when a RX queue corruption was detected from
macb_rx(), the RX queue was reset: during this process the RX ring
buffer descriptor was initialized by macb_init_rx_ring() but we forgot
to also set bp->rx_tail to 0.
Indeed, when processing the received frames, bp->rx_tail provides the
macb driver with the index in the RX ring buffer of the next buffer to
process. So when the whole ring buffer is reset we must also reset
bp->rx_tail so the driver is synchronized again with the hardware.
Since macb_init_rx_ring() is called from many locations, currently from
macb_rx() and macb_init_rings(), we'd rather add the "bp->rx_tail = 0;"
line inside macb_init_rx_ring() than add the very same line after each
call of this function.
Without this fix, the rx queue is not reset properly to recover from
queue corruption and connection drop may occur.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: 9ba723b081 ("net: macb: remove BUG_ON() and reset the queue to handle RX errors")
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
at91ether_start_xmit() does not check for dma mapping errors.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
New Cadence GEM hardware support Large Segment Offload (LSO):
TCP segmentation offload (TSO) as well as UDP fragmentation
offload (UFO). Support for those features was added to the driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some applications want to tune the size of the macb rx/tx ring buffers.
The ethtool set_ringparam function is the standard way of doing it.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macb driver hardcoded the tx/rx ring sizes. This made it
impossible to change the sizes at run time.
Add tx_ring_size, and rx_ring_size variables to macb object, which
are initilized with default vales during macb_init. Change all
references to RX_RING_SIZE and TX_RING_SIZE to their respective
replacements.
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ensure the dev->phydev pointer is not used after becoming invalid in
mdiobus_unregister, set it to NULL. This happens when removing the macb
driver without first taking its interface down, since unregister_netdev
will end up calling macb_close.
Signed-off-by: Xander Huff <xander.huff@ni.com>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Reviewed-by: Moritz Fischer <moritz.fischer@ettus.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix missing unlock before return from function macb_start_xmit()
in the error handling case.
Fixes: 007e4ba3ee ("net: macb: initialize checksum when using
checksum offloading")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm still struggling to get this fix right..
Changes since v2:
- do not blindly modify SKB contents according to Dave's legitimate
objection
Changes since v1:
- dropped disabling HW checksum offload for Zynq
- initialize checksum similar to net/ethernet/freescale/fec_main.c
-- >8 --
MACB/GEM needs the checksum field initialized to 0 to get correct
results on transmit in all cases, e.g. on Zynq, UDP packets with
payload <= 2 otherwise contain a wrong checksums.
Signed-off-by: Helmut Buchsbaum <helmut.buchsbaum@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the platforms like zynqmp ultrascale+ has a
separate clock gate for the rx clock. Add an optional
rx_clk so that the clock can be enabled.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing free_netdev() before return from function macb_probe()
in the platform_get_irq() error handling case.
Fixes: c69618b3e4 ("net/macb: fix probe sequence to setup clocks earlier")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for 64 bit addressing and BDs.
-> Enable 64 bit addressing in DMACFG register.
-> Set DMA mask when design config register shows support for 64 bit addr.
-> Add new BD words for higher address when 64 bit DMA support is present.
-> Add and update TBQPH and RBQPH for MSB of BD pointers.
-> Change extraction and updation of buffer addresses to use
64 bit address.
-> In gem_rx extract address in one place insted of two and use a
separate flag for RXUSED.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
USRIO and JUMBO CAPS have the same mask.
Fix the same.
Fixes: ce721a7021 ("net: ethernet: cadence-macb: Add disabled usrio caps")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phydev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The current sequence makes us register for a network device prior to
registering and probing the MDIO bus which could lead to some unwanted
consequences, like a thread of execution calling into ndo_open before
register_netdev() returns, while the MDIO bus is not ready yet.
Rework the sequence to register for the MDIO bus, and therefore attach
to a PHY prior to calling register_netdev(), which implies reworking the
error path a bit.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now mdiobus_scan() returns ERR_PTR(-ENODEV) instead of NULL if the PHY
device ID was read as all ones. As this was not an error before, this
value should be filtered out now in this driver.
Fixes: b74766a0a0 ("phylib: don't return NULL from get_phy_device()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checkpatch suggests using ether_addr_copy over memcpy
to copy the mac address.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit deals with a bunch of checkpatch suggestions
that without changing behavior make checkpatch happier.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit takes care of the coding style warnings
that are mostly due to a different comment style and
lines over 80 chars, as well as a dangling else.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl gave the following error:
ERROR: space required before the open parenthesis '('
+ for(; p < end; p++, offset += 4)
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GPIOlib will print warning messages if we call GPIO functions without a
valid GPIO. Change the code to avoid doing so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes two BUG_ON() used to notify about RX queue corruptions
on macb (not gem) hardware without actually handling the error.
The new code skips corrupted frames but still processes faultless frames.
Then it resets the RX queue before restarting the reception from a clean
state.
This patch is a rework of an older patch proposed by Neil Armstrong:
http://patchwork.ozlabs.org/patch/371525/
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_interrupt() should not use macb_writel(bp, ISR, <value>) but only
queue_writel(queue, ISR, <value>).
There is one IRQ and one set of {ISR, IER, IDR, IMR} [1] registers per
queue on gem hardware, though only queue0 is actually used for now to
receive frames: other queues can already be used to transmit frames.
The queue_readl() and queue_writel() helper macros are designed to access
the relevant IRQ registers.
[1]
ISR: Interrupt Status Register
IER: Interrupt Enable Register
IDR: Interrupt Disable Register
IMR: Interrupt Mask Register
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Fixes: bfbb92c446 ("net: macb: Handle the RXUBR interrupt on all devices")
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver calls gpiod_set_value() with GPIOD_OUT_* instead of 0 and 1, as
a result the PHY isn't really put back into reset state in macb_remove().
Moreover, the driver assumes that something else has set the GPIO direction
to output, so if it has not, the PHY may not be taken out of reset in
macb_probe() either...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On AT91 SoCs, the User Register (USRIO) exposes a switch to configure the
"Reduced" or "Traditional" version of the Media Independent Interface
(RMII vs. MII or RGMII vs. GMII).
As on the older EMAC version, on GMAC, this switch is set by default to the
non-reduced type of interface, so use the existing capability and extend it to
GMII as well. We then keep the current logic in the macb_init() function.
The capabilities of sama5d2, sama5d4 and sama5d3 GEM interface are updated in
the macb_config structure to be able to properly enable them with a traditional
interface (GMII or MII).
Reported-by: Romain HENRIET <romain.henriet@l-acoustics.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As requested by Rob Herring on patch
https://patchwork.ozlabs.org/patch/580862/.
This is a new property that it's still in net-next and has never been
used in production, so we are not breaking anything with the
incompatible binding change.
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested on Acqua A5 SoM (http://www.acmesystems.it/acqua).
Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are getting build warning about:
macb.c:2889:13: warning: 'tx_clk' may be used uninitialized in this function
macb.c:2888:11: warning: 'hclk' may be used uninitialized in this function
In reality they are not used uninitialized as clk_init() will initialize
them, this patch will just silence the warning.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disabling interrupts with the IDR register does not stop the macb hardware
from asserting its interrupt line if there are interrupts pending. Always
clear the interrupts using ISR, and be sure to write it on hardware that
is not read-to-clear, like Zynq. Not doing so will cause interrupts when
the driver doesn't expect them.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare a new NP4 SoC variant having USRIO_DISABLED as capability bit.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, the macb integration does not use the USRIO
register to configure the (R)MII port and clocks.
When the register is not implemented and the MACB error signal
is connected to the bus error, reading or writing to the USRIO
register can trigger some Imprecise External Aborts on ARM platforms.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of being at the MAC level the reset gpio preperty is moved at the
PHY child node level. It is still managed by the MAC, but from the point
of view of the binding it make more sense to be part of the PHY node.
This commit also fixes a build errors if GPIOLIB is not selected.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With device tree it is no more possible to reset the PHY at board
level. Furthermore, doing in the driver allow to power down the PHY when
the network interface is no more used.
This reset can't be done at the PHY driver level. The PHY must be able to
answer the to the mii bus scan to let the kernel creating a PHY device.
The patch introduces a new optional property "phy-reset-gpios" inspired
from the one use for the FEC.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the sgmii phy interface.
Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
If an architecture defines readl/writel using CPP macros, we
get the following kinds of build failure:
> > > drivers/net/ethernet/cadence/macb.c:164:1: error: macro "writel"
> > > passed 3 arguments, but takes just 2
> macb_or_gem_writel(bp, SA1B, bottom);
> ^
Rename the methods so that this doesn't happen.
Signed-off-by: David S. Miller <davem@davemloft.net>
macb_count_tx_descriptors() repeats the generic macro DIV_ROUND_UP(). The patch
does a replacement.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following warnings:
drivers/net/ethernet/cadence/macb.c: In function ‘macb_handle_link_change’:
drivers/net/ethernet/cadence/macb.c:266: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c:267: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c:291: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c: In function ‘gem_update_stats’:
drivers/net/ethernet/cadence/macb.c:1908: warning: comparison between signed and unsigned
drivers/net/ethernet/cadence/macb.c: In function ‘gem_get_ethtool_strings’:
drivers/net/ethernet/cadence/macb.c:1988: warning: comparison between signed and unsigned
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid messages like
macb macb.0 (unnamed net_device) (uninitialized): Cadence caps 0x00000000
macb macb.0 (unnamed net_device) (uninitialized): invalid hw address, using random
let's use dev_*() macros.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
