Some drivers (ath10k) report MCS 9 @ 20MHz, which
technically isn't defined. To get more meaningful value
than 0 out of this however, just extrapolate a bitrate
from ratio of MCS 7 and 9 in channels where it is allowed.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
[add a comment about it in the code]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This reverts commit c68df2e7be.
__sta_info_recalc_tim turns into a no-op if local->ops->set_tim is not
set. This prevents the beacon TIM bit from being set for all drivers
that do not implement this op (almost all of them), thus thoroughly
essential AP mode powersave functionality.
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: c68df2e7be ("mac80211: allow using AP_LINK_PS with mac80211-generated TIM IE")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is a workaround for VHT-enabled STAs which break the spec
and have the VHT-MCS Rx map filled in with value 3 for all eight
spacial streams, an example is AR9462 in AP mode.
As per spec, in section 22.1.1 Introduction to the VHT PHY
A VHT STA shall support at least single spactial stream VHT-MCSs
0 to 7 (transmit and receive) in all supported channel widths.
Some devices in STA mode will get firmware assert when trying to
associate, examples are QCA9377 & QCA6174.
Packet example of broken VHT Cap IE of AR9462:
Tag: VHT Capabilities (IEEE Std 802.11ac/D3.1)
Tag Number: VHT Capabilities (IEEE Std 802.11ac/D3.1) (191)
Tag length: 12
VHT Capabilities Info: 0x00000000
VHT Supported MCS Set
Rx MCS Map: 0xffff
.... .... .... ..11 = Rx 1 SS: Not Supported (0x0003)
.... .... .... 11.. = Rx 2 SS: Not Supported (0x0003)
.... .... ..11 .... = Rx 3 SS: Not Supported (0x0003)
.... .... 11.. .... = Rx 4 SS: Not Supported (0x0003)
.... ..11 .... .... = Rx 5 SS: Not Supported (0x0003)
.... 11.. .... .... = Rx 6 SS: Not Supported (0x0003)
..11 .... .... .... = Rx 7 SS: Not Supported (0x0003)
11.. .... .... .... = Rx 8 SS: Not Supported (0x0003)
...0 0000 0000 0000 = Rx Highest Long GI Data Rate (in Mb/s, 0 = subfield not in use): 0x0000
Tx MCS Map: 0xffff
...0 0000 0000 0000 = Tx Highest Long GI Data Rate (in Mb/s, 0 = subfield not in use): 0x0000
Signed-off-by: Filip Matusiak <filip.matusiak@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Some IPCB fields are currently set in udp_tunnel6_xmit_skb(), which are
never used before it reaches ip6tunnel_xmit(), and past that point the
control buffer is no longer interpreted as IPCB.
This clears these unused IPCB related codes. Currently there is no skb
scrubbing in ip6_udp_tunnel, otherwise IPCB(skb)->opt might need to be
cleared for IPv4 packets, as shown in 5146d1f151
("tunnel: Clear IPCB(skb)->opt before dst_link_failure called").
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Abstract unix domain socket may embed null characters,
these should be translated to '@' when printed out to
proc the same way the null prefix is currently being
translated.
This helps for tools such as netstat, lsof and the proc
based implementation in ss to show all the significant
bytes of the name (instead of getting cut at the first
null occurrence).
Signed-off-by: Isaac Boukris <iboukris@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEwBAABCgAaBQJYF6ANExxta2xAcGVuZ3V0cm9uaXguZGUACgkQPTuqJaypJWqQ
DAf+JRm7uhjaXEgITIhgiGIZBmCce7ONSBmBRr6cKcQyzMPaAHjfEZMcR5pltvH1
z03bspu5oug3bfSxk4iYK9hNxxAV+URxFxBDbOMdnolAsl6ZBcpOkx2jj/JFByZ5
fmOk8ChQr28qteEMLcTlm6O188eq2fZ+GUVZOh9iRslSVVcvGrM90NQoPFMUfP7G
On9+rZzSZlyNvdCSdFwrjUDzMVEW77P1Hv3gG10koefgIZKLelmMOIwDg7EvGTon
7HjqdZs6MFoSFAcbzJHB9lN0pAtK8nxWd3SPhdQof3kca8Dff/si4r5ZB2gAdSBq
w17LfdWoVE4p5/XvSyM4SM/X9A==
=Per+
-----END PGP SIGNATURE-----
Merge tag 'linux-can-fixes-for-4.9-20161031' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2016-10-31
this is a pull request of two patches for the upcoming v4.9 release.
The first patch is by Lukas Resch for the sja1000 plx_pci driver that adds
support for Moxa CAN devices. The second patch is by Oliver Hartkopp and fixes
a potential kernel panic in the CAN broadcast manager.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, in rx path, before calling lock_sock, it needed to
hold assoc when got it by __sctp_lookup_association, in case other place
would free/put assoc.
But in __sctp_lookup_association, it lookup and hold transport, then got
assoc by transport->assoc, then hold assoc and put transport. It means
it didn't hold transport, yet it was returned and later on directly
assigned to chunk->transport.
Without the protection of sock lock, the transport may be freed/put by
other places, which would cause a use-after-free issue.
This patch is to fix this issue by holding transport instead of assoc.
As holding transport can make sure to access assoc is also safe, and
actually it looks up assoc by searching transport rhashtable, to hold
transport here makes more sense.
Note that the function will be renamed later on on another patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, it used a local variable to save the transport that is
looked up by __sctp_lookup_association(), and didn't return it back. But in
sctp_rcv, it is used to initialize chunk->transport. So when hitting this,
even if it found the transport, it was still initializing chunk->transport
with null instead.
This patch is to return the transport back through transport pointer
that is from __sctp_rcv_lookup_harder().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sctp_transport_lookup_process(), Commit 1cceda7849 ("sctp: fix
the issue sctp_diag uses lock_sock in rcu_read_lock") moved cb() out
of rcu lock, but it put transport and hold assoc instead, and ignore
that cb() still uses transport. It may cause a use-after-free issue.
This patch is to hold transport instead of assoc there.
Fixes: 1cceda7849 ("sctp: fix the issue sctp_diag uses lock_sock in rcu_read_lock")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Konovalov reported an issue with proc_register in bcm.c.
As suggested by Cong Wang this patch adds a lock_sock() protection and
a check for unsuccessful proc_create_data() in bcm_connect().
Reference: http://marc.info/?l=linux-netdev&m=147732648731237
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Sending zero checksum is ok for TCP, but not for UDP.
UDPv6 receiver should by default drop a frame with a 0 checksum,
and UDPv4 would not verify the checksum and might accept a corrupted
packet.
Simply replace such checksum by 0xffff, regardless of transport.
This error was caught on SIT tunnels, but seems generic.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At accept() time, it is possible the parent has a non zero
sk_err_soft, leftover from a prior error.
Make sure we do not leave this value in the child, as it
makes future getsockopt(SO_ERROR) calls quite unreliable.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a congestion control module doesn't provide .undo_cwnd function,
tcp_undo_cwnd_reduction() will set cwnd to
tp->snd_cwnd = max(tp->snd_cwnd, tp->snd_ssthresh << 1);
... which makes sense for reno (it sets ssthresh to half the current cwnd),
but it makes no sense for dctcp, which sets ssthresh based on the current
congestion estimate.
This can cause severe growth of cwnd (eventually overflowing u32).
Fix this by saving last cwnd on loss and restore cwnd based on that,
similar to cubic and other algorithms.
Fixes: e3118e8359 ("net: tcp: add DCTCP congestion control algorithm")
Cc: Lawrence Brakmo <brakmo@fb.com>
Cc: Andrew Shewmaker <agshew@gmail.com>
Cc: Glenn Judd <glenn.judd@morganstanley.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, ipv6 didn't do mtu lock check in ip6_update_pmtu.
It leaded to that mtu lock doesn't really work when receiving the pkt
of ICMPV6_PKT_TOOBIG.
This patch is to add mtu lock check in __ip6_rt_update_pmtu just as ipv4
did in __ip_rt_update_pmtu.
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to commit c146066ab8 ("ipv4: Don't use ufo handling on later
transformed packets"), don't perform UFO on packets that will be IPsec
transformed. To detect it we rely on the fact that headerlen in
dst_entry is non-zero only for transformation bundles (xfrm_dst
objects).
Unwanted segmentation can be observed with a NETIF_F_UFO capable device,
such as a dummy device:
DEV=dum0 LEN=1493
ip li add $DEV type dummy
ip addr add fc00::1/64 dev $DEV nodad
ip link set $DEV up
ip xfrm policy add dir out src fc00::1 dst fc00::2 \
tmpl src fc00::1 dst fc00::2 proto esp spi 1
ip xfrm state add src fc00::1 dst fc00::2 \
proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b
tcpdump -n -nn -i $DEV -t &
socat /dev/zero,readbytes=$LEN udp6:[fc00::2]:$LEN
tcpdump output before:
IP6 fc00::1 > fc00::2: frag (0|1448) ESP(spi=0x00000001,seq=0x1), length 1448
IP6 fc00::1 > fc00::2: frag (1448|48)
IP6 fc00::1 > fc00::2: ESP(spi=0x00000001,seq=0x2), length 88
... and after:
IP6 fc00::1 > fc00::2: frag (0|1448) ESP(spi=0x00000001,seq=0x1), length 1448
IP6 fc00::1 > fc00::2: frag (1448|80)
Fixes: e89e9cf539 ("[IPv4/IPv6]: UFO Scatter-gather approach")
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
In commit 2d18ac4ba7 ("tipc: extend broadcast link initialization
criteria") we tried to fix a problem with the initial synchronization
of broadcast link acknowledge values. Unfortunately that solution is
not sufficient to solve the issue.
We have seen it happen that LINK_PROTOCOL/STATE packets with a valid
non-zero unicast acknowledge number may bypass BCAST_PROTOCOL
initialization, NAME_DISTRIBUTOR and other STATE packets with invalid
broadcast acknowledge numbers, leading to premature opening of the
broadcast link. When the bypassed packets finally arrive, they are
inadvertently accepted, and the already correctly initialized
acknowledge number in the broadcast receive link is overwritten by
the invalid (zero) value of the said packets. After this the broadcast
link goes stale.
We now fix this by marking the packets where we know the acknowledge
value is or may be invalid, and then ignoring the acks from those.
To this purpose, we claim an unused bit in the header to indicate that
the value is invalid. We set the bit to 1 in the initial BCAST_PROTOCOL
synchronization packet and all initial ("bulk") NAME_DISTRIBUTOR
packets, plus those LINK_PROTOCOL packets sent out before the broadcast
links are fully synchronized.
This minor protocol update is fully backwards compatible.
Reported-by: John Thompson <thompa.atl@gmail.com>
Tested-by: John Thompson <thompa.atl@gmail.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rds use Kconfig option called "RDS_DEBUG" to enable rds debug messages.
This option cause the rds Makefile to add -DDEBUG to the rds gcc command
line.
When CONFIG_DYNAMIC_DEBUG is enabled, the "DEBUG" macro is used by
include/linux/dynamic_debug.h to decide if dynamic debug prints should
be sent by default to the kernel log.
rds should not enable this macro for production builds. rds dynamic
debug work as expected follow this fix.
Signed-off-by: Shamir Rabinovitch <shamir.rabinovitch@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Reviewed-by: Wengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* a fix to process all events while suspending, so any
potential calls into the driver are done before it is
suspended
* small markup fixes for the sphinx documentation conversion
that's coming into the tree via the doc tree
-----BEGIN PGP SIGNATURE-----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=toQY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2016-10-27' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two fixes:
* a fix to process all events while suspending, so any
potential calls into the driver are done before it is
suspended
* small markup fixes for the sphinx documentation conversion
that's coming into the tree via the doc tree
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix RCU usage for neighbor list, by Sven Eckelmann
- Fix BATADV_DBG_ALL loglevel to include TP Meter messages, by Sven Eckelmann
- Fix possible splat when disabling an interface, by Linus Luessing
-----BEGIN PGP SIGNATURE-----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=/5y8
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20161026' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are three batman-adv bugfix patches:
- Fix RCU usage for neighbor list, by Sven Eckelmann
- Fix BATADV_DBG_ALL loglevel to include TP Meter messages, by Sven Eckelmann
- Fix possible splat when disabling an interface, by Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When transmitting on a packet socket with PACKET_VNET_HDR and
PACKET_QDISC_BYPASS, validate device support for features requested
in vnet_hdr.
Drop TSO packets sent to devices that do not support TSO or have the
feature disabled. Note that the latter currently do process those
packets correctly, regardless of not advertising the feature.
Because of SKB_GSO_DODGY, it is not sufficient to test device features
with netif_needs_gso. Full validate_xmit_skb is needed.
Switch to software checksum for non-TSO packets that request checksum
offload if that device feature is unsupported or disabled. Note that
similar to the TSO case, device drivers may perform checksum offload
correctly even when not advertising it.
When switching to software checksum, packets hit skb_checksum_help,
which has two BUG_ON checksum not in linear segment. Packet sockets
always allocate at least up to csum_start + csum_off + 2 as linear.
Tested by running github.com/wdebruij/kerneltools/psock_txring_vnet.c
ethtool -K eth0 tso off tx on
psock_txring_vnet -d $dst -s $src -i eth0 -l 2000 -n 1 -q -v
psock_txring_vnet -d $dst -s $src -i eth0 -l 2000 -n 1 -q -v -N
ethtool -K eth0 tx off
psock_txring_vnet -d $dst -s $src -i eth0 -l 1000 -n 1 -q -v -G
psock_txring_vnet -d $dst -s $src -i eth0 -l 1000 -n 1 -q -v -G -N
v2:
- add EXPORT_SYMBOL_GPL(validate_xmit_skb_list)
Fixes: d346a3fae3 ("packet: introduce PACKET_QDISC_BYPASS socket option")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use nla_parse_nested instead of open-coding the call to
nla_parse() with the attribute data/len.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates skb->protocol to ETH_P_IPV6 in ip6_tnl_xmit() when an
IPv6 header is installed to a socket buffer.
This is not a cosmetic change. Without updating this value, GSO packets
transmitted through an ipip6 tunnel have the protocol of ETH_P_IP and
skb_mac_gso_segment() will attempt to call gso_segment() for IPv4,
which results in the packets being dropped.
Fixes: b8921ca83e ("ip4ip6: Support for GSO/GRO")
Signed-off-by: Eli Cooper <elicooper@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of a series to implement faster SO_REUSEPORT lookups,
commit 086c653f58 ("sock: struct proto hash function may error")
added return values to protocol hash functions and
commit 496611d7b5 ("inet: create IPv6-equivalent inet_hash function")
implemented a new hash function for IPv6. However, the latter does
not respect the former's convention.
This properly propagates the hash errors in the IPv6 case.
Fixes: 496611d7b5 ("inet: create IPv6-equivalent inet_hash function")
Reported-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Craig Gallek <kraig@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Konovalov reported that KASAN detected that SCTP was using a slab
beyond the boundaries. It was caused because when handling out of the
blue packets in function sctp_sf_ootb() it was checking the chunk len
only after already processing the first chunk, validating only for the
2nd and subsequent ones.
The fix is to just move the check upwards so it's also validated for the
1st chunk.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel says:
While trying out [1][2], I noticed that tc monitor doesn't show the
correct handle on delete:
$ tc monitor
qdisc clsact ffff: dev eno1 parent ffff:fff1
filter dev eno1 ingress protocol all pref 49152 bpf handle 0x2a [...]
deleted filter dev eno1 ingress protocol all pref 49152 bpf handle 0xf3be0c80
some context to explain the above:
The user identity of any tc filter is represented by a 32-bit
identifier encoded in tcm->tcm_handle. Example 0x2a in the bpf filter
above. A user wishing to delete, get or even modify a specific filter
uses this handle to reference it.
Every classifier is free to provide its own semantics for the 32 bit handle.
Example: classifiers like u32 use schemes like 800:1:801 to describe
the semantics of their filters represented as hash table, bucket and
node ids etc.
Classifiers also have internal per-filter representation which is different
from this externally visible identity. Most classifiers set this
internal representation to be a pointer address (which allows fast retrieval
of said filters in their implementations). This internal representation
is referenced with the "fh" variable in the kernel control code.
When a user successfuly deletes a specific filter, by specifying the correct
tcm->tcm_handle, an event is generated to user space which indicates
which specific filter was deleted.
Before this patch, the "fh" value was sent to user space as the identity.
As an example what is shown in the sample bpf filter delete event above
is 0xf3be0c80. This is infact a 32-bit truncation of 0xffff8807f3be0c80
which happens to be a 64-bit memory address of the internal filter
representation (address of the corresponding filter's struct cls_bpf_prog);
After this patch the appropriate user identifiable handle as encoded
in the originating request tcm->tcm_handle is generated in the event.
One of the cardinal rules of netlink rules is to be able to take an
event (such as a delete in this case) and reflect it back to the
kernel and successfully delete the filter. This patch achieves that.
Note, this issue has existed since the original TC action
infrastructure code patch back in 2004 as found in:
https://git.kernel.org/cgit/linux/kernel/git/history/history.git/commit/
[1] http://patchwork.ozlabs.org/patch/682828/
[2] http://patchwork.ozlabs.org/patch/682829/
Fixes: 4e54c4816bfe ("[NET]: Add tc extensions infrastructure.")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc warns about an uninitialized pointer dereference in the vlan
priority handling:
net/core/flow_dissector.c: In function '__skb_flow_dissect':
net/core/flow_dissector.c:281:61: error: 'vlan' may be used uninitialized in this function [-Werror=maybe-uninitialized]
As pointed out by Jiri Pirko, the variable is never actually used
without being initialized first as the only way it end up uninitialized
is with skb_vlan_tag_present(skb)==true, and that means it does not
get accessed.
However, the warning hints at some related issues that I'm addressing
here:
- the second check for the vlan tag is different from the first one
that tests the skb for being NULL first, causing both the warning
and a possible NULL pointer dereference that was not entirely fixed.
- The same patch that introduced the NULL pointer check dropped an
earlier optimization that skipped the repeated check of the
protocol type
- The local '_vlan' variable is referenced through the 'vlan' pointer
but the variable has gone out of scope by the time that it is
accessed, causing undefined behavior
Caching the result of the 'skb && skb_vlan_tag_present(skb)' check
in a local variable allows the compiler to further optimize the
later check. With those changes, the warning also disappears.
Fixes: 3805a938a6 ("flow_dissector: Check skb for VLAN only if skb specified.")
Fixes: d5709f7ab7 ("flow_dissector: For stripped vlan, get vlan info from skb->vlan_tci")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Eric Garver <e@erig.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to IPv4, do not consider link state when validating next hops.
Currently, if the link is down default routes can fail to insert:
$ ip -6 ro add vrf blue default via 2100:2::64 dev eth2
RTNETLINK answers: No route to host
With this patch the command succeeds.
Fixes: 8c14586fc3 ("net: ipv6: Use passed in table for nexthop lookups")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt6_add_route_info and rt6_add_dflt_router were updated to pull the FIB
table from the device index, but the corresponding rt6_get_route_info
and rt6_get_dflt_router functions were not leading to the failure to
process RA's:
ICMPv6: RA: ndisc_router_discovery failed to add default route
Fix the 'get' functions by using the table id associated with the
device when applicable.
Also, now that default routes can be added to tables other than the
default table, rt6_purge_dflt_routers needs to be updated as well to
look at all tables. To handle that efficiently, add a flag to the table
denoting if it is has a default route via RA.
Fixes: ca254490c8 ("net: Add VRF support to IPv6 stack")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First bug was added in commit ad6f939ab1 ("ip: Add offset parameter to
ip_cmsg_recv") : Tom missed that ipv4 udp messages could be received on
AF_INET6 socket. ip_cmsg_recv(msg, skb) should have been replaced by
ip_cmsg_recv_offset(msg, skb, sizeof(struct udphdr));
Then commit e6afc8ace6 ("udp: remove headers from UDP packets before
queueing") forgot to adjust the offsets now UDP headers are pulled
before skb are put in receive queue.
Fixes: ad6f939ab1 ("ip: Add offset parameter to ip_cmsg_recv")
Fixes: e6afc8ace6 ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Sam Kumar <samanthakumar@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Tested-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7303a14750 ("sctp: identify chunks that need to be fragmented
at IP level") made the chunk be fragmented at IP level in the next round
if it's size exceed PMTU.
But there still is another case, PMTU can be updated if transport's dst
expires and transport's pmtu_pending is set in sctp_packet_transmit. If
the new PMTU is less than the chunk, the same issue with that commit can
be triggered.
So we should drop this packet and let it retransmit in another round
where it would be fragmented at IP level.
This patch is to fix it by checking the chunk size after PMTU may be
updated and dropping this packet if it's size exceed PMTU.
Fixes: 90017accff ("sctp: Add GSO support")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When suspending without WoWLAN, cfg80211 will ask drivers to
disconnect. Even when the driver does this synchronously, and
immediately returns with a notification, cfg80211 schedules
the handling thereof to a workqueue, and may then call back
into the driver when the driver was already suspended/ing.
Fix this by processing all events caused by cfg80211_leave_all()
directly after that function returns. The driver still needs to
do the right thing here and wait for the firmware response, but
that is - at least - true for mwifiex where this occurred.
Reported-by: Amitkumar Karwar <akarwar@marvell.com>
Tested-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Johan Hedberg says:
====================
pull request: bluetooth 2016-10-21
Here are some more Bluetooth fixes for the 4.9 kernel:
- Fix to btwilink driver probe function return value
- Power management fix to hci_bcm
- Fix to encoding name in scan response data
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of getsockopt handlers in net/sctp/socket.c check len against
sizeof some structure like:
if (len < sizeof(int))
return -EINVAL;
On the first look, the check seems to be correct. But since len is int
and sizeof returns size_t, int gets promoted to unsigned size_t too. So
the test returns false for negative lengths. Yes, (-1 < sizeof(long)) is
false.
Fix this in sctp by explicitly checking len < 0 before any getsockopt
handler is called.
Note that sctp_getsockopt_events already handled the negative case.
Since we added the < 0 check elsewhere, this one can be removed.
If not checked, this is the result:
UBSAN: Undefined behaviour in ../mm/page_alloc.c:2722:19
shift exponent 52 is too large for 32-bit type 'int'
CPU: 1 PID: 24535 Comm: syz-executor Not tainted 4.8.1-0-syzkaller #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.9.1-0-gb3ef39f-prebuilt.qemu-project.org 04/01/2014
0000000000000000 ffff88006d99f2a8 ffffffffb2f7bdea 0000000041b58ab3
ffffffffb4363c14 ffffffffb2f7bcde ffff88006d99f2d0 ffff88006d99f270
0000000000000000 0000000000000000 0000000000000034 ffffffffb5096422
Call Trace:
[<ffffffffb3051498>] ? __ubsan_handle_shift_out_of_bounds+0x29c/0x300
...
[<ffffffffb273f0e4>] ? kmalloc_order+0x24/0x90
[<ffffffffb27416a4>] ? kmalloc_order_trace+0x24/0x220
[<ffffffffb2819a30>] ? __kmalloc+0x330/0x540
[<ffffffffc18c25f4>] ? sctp_getsockopt_local_addrs+0x174/0xca0 [sctp]
[<ffffffffc18d2bcd>] ? sctp_getsockopt+0x10d/0x1b0 [sctp]
[<ffffffffb37c1219>] ? sock_common_getsockopt+0xb9/0x150
[<ffffffffb37be2f5>] ? SyS_getsockopt+0x1a5/0x270
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-sctp@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise we'll overflow the integer. This occurs when layer 3 tunneled
packets are handed off to the IPv6 layer.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a681574c99
("ipv4: disable BH in set_ping_group_range()") because we never
read ping_group_range in BH context (unlike local_port_range).
Then, since we already have a lock for ping_group_range, those
using ip_local_ports.lock for ping_group_range are clearly typos.
We might consider to share a same lock for both ping_group_range
and local_port_range w.r.t. space saving, but that should be for
net-next.
Fixes: a681574c99 ("ipv4: disable BH in set_ping_group_range()")
Fixes: ba6b918ab2 ("ping: move ping_group_range out of CONFIG_SYSCTL")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Eric Salo <salo@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit bc51dddf98 ("netns: avoid disabling irq for
netns id") as it was found to cause problems with systems running
SELinux/audit, see the mailing list thread below:
* http://marc.info/?t=147694653900002&r=1&w=2
Eventually we should be able to reintroduce this code once we have
rewritten the audit multicast code to queue messages much the same
way we do for unicast messages. A tracking issue for this can be
found below:
* https://github.com/linux-audit/audit-kernel/issues/23
Reported-by: Stephen Smalley <sds@tycho.nsa.gov>
Reported-by: Elad Raz <e@eladraz.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Baozeng reported this deadlock case:
CPU0 CPU1
---- ----
lock([ 165.136033] sk_lock-AF_INET6);
lock([ 165.136033] rtnl_mutex);
lock([ 165.136033] sk_lock-AF_INET6);
lock([ 165.136033] rtnl_mutex);
Similar to commit 87e9f03159
("ipv4: fix a potential deadlock in mcast getsockopt() path")
this is due to we still have a case, ipv6_sock_mc_close(),
where we acquire sk_lock before rtnl_lock. Close this deadlock
with the similar solution, that is always acquire rtnl lock first.
Fixes: baf606d9c9 ("ipv4,ipv6: grab rtnl before locking the socket")
Reported-by: Baozeng Ding <sploving1@gmail.com>
Tested-by: Baozeng Ding <sploving1@gmail.com>
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Fix compilation warning in xt_hashlimit on m68k 32-bits, from
Geert Uytterhoeven.
2) Fix wrong timeout in set elements added from packet path via
nft_dynset, from Anders K. Pedersen.
3) Remove obsolete nf_conntrack_events_retry_timeout sysctl
documentation, from Nicolas Dichtel.
4) Ensure proper initialization of log flags via xt_LOG, from
Liping Zhang.
5) Missing alias to autoload ipcomp, also from Liping Zhang.
6) Missing NFTA_HASH_OFFSET attribute validation, again from Liping.
7) Wrong integer type in the new nft_parse_u32_check() function,
from Dan Carpenter.
8) Another wrong integer type declaration in nft_exthdr_init, also
from Dan Carpenter.
9) Fix insufficient mode validation in nft_range.
10) Fix compilation warning in nft_range due to possible uninitialized
value, from Arnd Bergmann.
11) Zero nf_hook_ops allocated via xt_hook_alloc() in x_tables to
calm down kmemcheck, from Florian Westphal.
12) Schedule gc_worker() to run again if GC_MAX_EVICTS quota is reached,
from Nicolas Dichtel.
13) Fix nf_queue() after conversion to single-linked hook list, related
to incorrect bypass flag handling and incorrect hook point of
reinjection.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As long as there is still a reference for a hard interface held, there might
still be a forwarding packet relying on its attributes.
Therefore avoid setting hard_iface->soft_iface to NULL when disabling a hard
interface.
This fixes the following, potential splat:
batman_adv: bat0: Interface deactivated: eth1
batman_adv: bat0: Removing interface: eth1
cgroup: new mount options do not match the existing superblock, will be ignored
batman_adv: bat0: Interface deactivated: eth3
batman_adv: bat0: Removing interface: eth3
------------[ cut here ]------------
WARNING: CPU: 3 PID: 1986 at ./net/batman-adv/bat_iv_ogm.c:549 batadv_iv_send_outstanding_bat_ogm_packet+0x145/0x643 [batman_adv]
Modules linked in: batman_adv(O-) <...>
CPU: 3 PID: 1986 Comm: kworker/u8:2 Tainted: G W O 4.6.0-rc6+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
Workqueue: bat_events batadv_iv_send_outstanding_bat_ogm_packet [batman_adv]
0000000000000000 ffff88001d93bca0 ffffffff8126c26b 0000000000000000
0000000000000000 ffff88001d93bcf0 ffffffff81051615 ffff88001f19f818
000002251d93bd68 0000000000000046 ffff88001dc04a00 ffff88001becbe48
Call Trace:
[<ffffffff8126c26b>] dump_stack+0x67/0x90
[<ffffffff81051615>] __warn+0xc7/0xe5
[<ffffffff8105164b>] warn_slowpath_null+0x18/0x1a
[<ffffffffa0356f24>] batadv_iv_send_outstanding_bat_ogm_packet+0x145/0x643 [batman_adv]
[<ffffffff8108b01f>] ? __lock_is_held+0x32/0x54
[<ffffffff810689a2>] process_one_work+0x2a8/0x4f5
[<ffffffff81068856>] ? process_one_work+0x15c/0x4f5
[<ffffffff81068df2>] worker_thread+0x1d5/0x2c0
[<ffffffff81068c1d>] ? process_scheduled_works+0x2e/0x2e
[<ffffffff81068c1d>] ? process_scheduled_works+0x2e/0x2e
[<ffffffff8106dd90>] kthread+0xc0/0xc8
[<ffffffff8144de82>] ret_from_fork+0x22/0x40
[<ffffffff8106dcd0>] ? __init_kthread_worker+0x55/0x55
---[ end trace 647f9f325123dc05 ]---
What happened here is, that there was still a forw_packet (here: a BATMAN IV
OGM) in the queue of eth3 with the forw_packet->if_incoming set to eth1 and the
forw_packet->if_outgoing set to eth3.
When eth3 is to be deactivated and removed, then this thread waits for the
forw_packet queued on eth3 to finish. Because eth1 was deactivated and removed
earlier and by that had forw_packet->if_incoming->soft_iface, set to NULL, the
splat when trying to send/flush the OGM on eth3 occures.
Fixes: c6c8fea297 ("net: Add batman-adv meshing protocol")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
[sven@narfation.org: Reduced size of Oops message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In commit 4ee3bd4a8c ("ipv4: disable BH when changing ip local port
range") Cong added BH protection in set_local_port_range() but missed
that same fix was needed in set_ping_group_range()
Fixes: b8f1a55639 ("udp: Add function to make source port for UDP tunnels")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Eric Salo <salo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Baozeng Ding reported KASAN traces showing uses after free in
udp_lib_get_port() and other related UDP functions.
A CONFIG_DEBUG_PAGEALLOC=y kernel would eventually crash.
I could write a reproducer with two threads doing :
static int sock_fd;
static void *thr1(void *arg)
{
for (;;) {
connect(sock_fd, (const struct sockaddr *)arg,
sizeof(struct sockaddr_in));
}
}
static void *thr2(void *arg)
{
struct sockaddr_in unspec;
for (;;) {
memset(&unspec, 0, sizeof(unspec));
connect(sock_fd, (const struct sockaddr *)&unspec,
sizeof(unspec));
}
}
Problem is that udp_disconnect() could run without holding socket lock,
and this was causing list corruptions.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Baozeng Ding <sploving1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, GRO can do unlimited recursion through the gro_receive
handlers. This was fixed for tunneling protocols by limiting tunnel GRO
to one level with encap_mark, but both VLAN and TEB still have this
problem. Thus, the kernel is vulnerable to a stack overflow, if we
receive a packet composed entirely of VLAN headers.
This patch adds a recursion counter to the GRO layer to prevent stack
overflow. When a gro_receive function hits the recursion limit, GRO is
aborted for this skb and it is processed normally. This recursion
counter is put in the GRO CB, but could be turned into a percpu counter
if we run out of space in the CB.
Thanks to Vladimír Beneš <vbenes@redhat.com> for the initial bug report.
Fixes: CVE-2016-7039
Fixes: 9b174d88c2 ("net: Add Transparent Ethernet Bridging GRO support.")
Fixes: 66e5133f19 ("vlan: Add GRO support for non hardware accelerated vlan")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for an underflow of tmp_prefered_lft is always false
because tmp_prefered_lft is unsigned. The intention of the check
was to guard against racing with an update of the
temp_prefered_lft sysctl, potentially resulting in an underflow.
As suggested by David Miller, the best way to prevent the race is
by reading the sysctl variable using READ_ONCE.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Fixes: 76506a986d ("IPv6: fix DESYNC_FACTOR")
Signed-off-by: David S. Miller <davem@davemloft.net>
nf_queue handling is broken since e3b37f11e6 ("netfilter: replace
list_head with single linked list") for two reasons:
1) If the bypass flag is set on, there are no userspace listeners and
we still have more hook entries to iterate over, then jump to the
next hook. Otherwise accept the packet. On nf_reinject() path, the
okfn() needs to be invoked.
2) We should not re-enter the same hook on packet reinjection. If the
packet is accepted, we have to skip the current hook from where the
packet was enqueued, otherwise the packets gets enqueued over and
over again.
This restores the previous list_for_each_entry_continue() behaviour
happening from nf_iterate() that was dealing with these two cases.
This patch introduces a new nf_queue() wrapper function so this fix
becomes simpler.
Fixes: e3b37f11e6 ("netfilter: replace list_head with single linked list")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When the maximum evictions number is reached, do not wait 5 seconds before
the next run.
CC: Florian Westphal <fw@strlen.de>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This improves AEN handler for Host Network Controller Driver Status
Change (HNCDSC):
* The channel's lock should be hold when accessing its state.
* Do failover when host driver isn't ready.
* Configure channel when host driver becomes ready.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue was found on BCM5718 which has two NCSI channels in one
package: C0 and C1. C0 is in link-up state while C1 is in link-down
state. C0 is chosen as active channel until unplugging and plugging
C0's cable: On unplugging C0's cable, LSC (Link State Change) AEN
packet received on C0 to report link-down event. After that, C1 is
chosen as active channel. LSC AEN for link-up event is lost on C0
when plugging C0's cable back. We lose the network even C0 is usable.
This resolves the issue by recording the (hot) channel that was ever
chosen as active one. The hot channel is chosen to be active one
if none of available channels in link-up state. With this, C0 is still
the active one after unplugging C0's cable. LSC AEN packet received
on C0 when plugging its cable back.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The issue was found on BCM5718 which has two NCSI channels in one
package: C0 and C1. Both of them are connected to different LANs,
means they are in link-up state and C0 is chosen as the active one
until resetting BCM5718 happens as below.
Resetting BCM5718 results in LSC (Link State Change) AEN packet
received on C0, meaning LSC AEN is missed on C1. When LSC AEN packet
received on C0 to report link-down, it fails over to C1 because C1
is in link-up state as software can see. However, C1 is in link-down
state in hardware. It means the link state is out of synchronization
between hardware and software, resulting in inappropriate channel (C1)
selected as active one.
This resolves the issue by sending separate GLS (Get Link Status)
commands to all channels in the package before trying to do failover.
The last link states of all channels in the package are retrieved.
With it, C0 (not C1) is selected as active one as expected.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several if/else statements in the state machine implemented
by switch/case in ncsi_suspend_channel() to avoid duplicated code. It
makes the code a bit hard to be understood.
This drops if/else statements in ncsi_suspend_channel() to improve the
code readability as Joel Stanley suggested. Also, it becomes easy to
add more states in the state machine without affecting current code.
No logical changes introduced by this.
Suggested-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
