When the VF driver does a reset, it (at least the Linux one) writes to
the VFCTRL register to issue a reset and then immediately sends a reset
message using the mailbox API. This is racy because when the PF driver
detects that the VFCTRL register reset pin has been asserted, it clears
the mailbox memory. Depending on ordering, the reset message sent by
the VF could be cleared by the PF driver. It then responds to the
cleared message with a NACK which causes the VF driver to malfunction.
Fix this by deferring clearing the mailbox memory until the reset
message is received.
Fixes: 939b701ad6 ("ixgbe: fix driver behaviour after issuing VFLR")
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move rx_ptype extracting to i40e_process_skb_fields() to avoid
duplicating the code.
Signed-off-by: Michał Mirosław <michal.miroslaw@atendesoftware.pl>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This fixes two bugs in hardware VLAN offload:
1. VLAN.TCI == 0 was being dropped
2. there was a race between disabling of VLAN RX feature in hardware
and processing RX queue, where packets processed in this window
could have their VLAN information dropped
Fix moves the VLAN handling into i40e_process_skb_fields() to save on
duplicated code. i40e_receive_skb() becomes trivial and so is removed.
Signed-off-by: Michał Mirosław <michal.miroslaw@atendesoftware.pl>
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous commit moved the ether_addr_copy() in i40e_set_mac() before
the mac filter del/add to avoid a race. However it wasn't taken into
account that this alters the mac address being handed to
i40e_del_mac_filter().
Also changed i40e_add_mac_filter() to operate on netdev->dev_addr,
hopefully that makes the code easier to read.
Fixes: 458867b2ca ("i40e: don't remove netdev->dev_addr when syncing uc list")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
One method, xsk_umem_setup, had an incorrect kernel doc
description, which has been corrected.
Also fixes small typos found in the comments.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the two 1000BaseLX enum values to the X550's check for 1Gbps modules,
allowing the core driver code to establish a link over this SFP type.
This is done by the out-of-tree driver but the fix wasn't in mainline.
Fixes: e23f333678 ("ixgbe: Fix 1G and 10G link stability for X550EM_x SFP+”)
Fixes: 6a14ee0cfb ("ixgbe: Add X550 support function pointers")
Signed-off-by: Josh Elsasser <jelsasser@appneta.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In __i40e_del_filter function, the flag __I40E_MACVLAN_SYNC_PENDING for
the PF state is wrongly set for the VSI. Deleting any of the MAC filters
has caused the incorrect syncing for the PF. Fix it by setting this state
flag to the intended PF.
CC: stable <stable@vger.kernel.org>
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the variable 'phy_word' may be used uninitialized.
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The assignment of the feature flag NETIF_F_NTUPLE and NETIF_F_HW_TC
occurs prior to the initial setup of the local hw_features variable.
This means the features are set as user-changeable, but are not set in
the currently active feature list. This results in the features being
disabled at the driver's initial load.
Move the assignment after the initial assignment of hw_features, and
assign to the local variable. This ensures that NETIF_F_NTUPLE and
NETIF_F_HW_TC are marked as user-changeable, and also enables them by
default when the driver loads.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit bacd75cfac ("i40e/i40evf: Add capability exchange for
outer checksum", 2017-04-06) the i40e driver has not reported support
for IP-in-IP offloads. This likely occurred due to a bad rebase, as the
commit extracts hw_enc_features into its own variable. As part of this
change, it dropped the NETIF_F_FSO_IPXIP flags from the
netdev->hw_enc_features. This was unfortunately not caught during code
review.
Fix this by adding back the missing feature flags.
For reference, NETIF_F_GSO_IPXIP4 was added in commit 7e13318daa
("net: define gso types for IPx over IPv4 and IPv6", 2016-05-20),
replacing NETIF_F_GSO_IPIP and NETIF_F_GSO_SIT.
NETIF_F_GSO_IPXIP6 was added in commit bf2d1df395 ("intel: Add support
for IPv6 IP-in-IP offload", 2016-05-20).
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since the req_speeds field in struct ice_link_status is a u8,
req_speeds & ICE_AQ_LINK_SPEED_40GB always returns 0. This was caught
by a coverity scan.
Fix this by changing req_speeds to be u16.
Reported-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The timecounter needs to be updated at least once per ~550 seconds in
order to avoid a 40-bit SYSTIM timestamp to be misinterpreted as an old
timestamp.
Since commit 500462a9de ("timers: Switch to a non-cascading wheel"),
scheduling of delayed work seems to be less accurate and a requested
delay of 540 seconds may actually be longer than 550 seconds. Also, the
PHC may be adjusted to run up to 6% faster than real time and the system
clock up to 10% slower. Shorten the delay to 360 seconds to be sure the
timecounter is updated in time.
This fixes an issue with HW timestamps on 82580/I350/I354 being off by
~1100 seconds for few seconds every ~9 minutes.
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the driver does a TSO offload the bytecount sent to
netdev_tx_sent_queue will be incorrect. This is because in ice_tso we
overwrite the initial value that we set in ice_tx_map. This creates a
mismatch between the Tx and Tx clean flow. In the Tx clean flow we
calculate the bytecount (called total_bytes) as we clean the
descriptors so the value used in the Tx clean path is correct. Fix this
by using += in ice_tso instead of =. This fixes the mismatch in
bytecount mentioned above.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prior to this commit the driver was running into tx_timeouts when a
queue was stressed enough. This was happening because the HW tail
and SW tail (NTU) were incorrectly out of sync. Consequently this was
causing the HW head to collide with the HW tail, which to the hardware
means that all descriptors posted for Tx have been processed.
Due to the Tx logic used in the driver SW tail and HW tail are allowed
to be out of sync. This is done as an optimization because it allows the
driver to write HW tail as infrequently as possible, while still
updating the SW tail index to keep track. However, there are situations
where this results in the tail never getting updated, resulting in Tx
timeouts.
Tx HW tail write condition:
if (netif_xmit_stopped(txring_txq(tx_ring) || !skb->xmit_more)
writel(sw_tail, tx_ring->tail);
An issue was found in the Tx logic that was causing the afore mentioned
condition for updating HW tail to never happen, causing tx_timeouts.
In ice_xmit_frame_ring we calculate how many descriptors we need for the
Tx transaction based on the skb the kernel hands us. This is then passed
into ice_maybe_stop_tx along with some extra padding to determine if we
have enough descriptors available for this transaction. If we don't then
we return -EBUSY to the stack, otherwise we move on and eventually
prepare the Tx descriptors accordingly in ice_tx_map and set
next_to_watch. In ice_tx_map we make another call to ice_maybe_stop_tx
with a value of MAX_SKB_FRAGS + 4. The key here is that this value is
possibly less than the value we sent in the first call to
ice_maybe_stop_tx in ice_xmit_frame_ring. Now, if the number of unused
descriptors is between MAX_SKB_FRAGS + 4 and the value used in the first
call to ice_maybe_stop_tx in ice_xmit_frame_ring then we do not update
the HW tail because of the "Tx HW tail write condition" above. This is
because in ice_maybe_stop_tx we return success from ice_maybe_stop_tx
instead of calling __ice_maybe_stop_tx and subsequently calling
netif_stop_subqueue, which sets the __QUEUE_STATE_DEV_XOFF bit. This
bit is then checked in the "Tx HW tail write condition" by calling
netif_xmit_stopped and subsequently updating HW tail if the
afore mentioned bit is set.
In ice_clean_tx_irq, if next_to_watch is not NULL, we end up cleaning
the descriptors that HW sets the DD bit on and we have the budget. The
HW head will eventually run into the HW tail in response to the
description in the paragraph above.
The next time through ice_xmit_frame_ring we make the initial call to
ice_maybe_stop_tx with another skb from the stack. This time we do not
have enough descriptors available and we return NETDEV_TX_BUSY to the
stack and end up setting next_to_watch to NULL.
This is where we are stuck. In ice_clean_tx_irq we never clean anything
because next_to_watch is always NULL and in ice_xmit_frame_ring we never
update HW tail because we already return NETDEV_TX_BUSY to the stack and
eventually we hit a tx_timeout.
This issue was fixed by making sure that the second call to
ice_maybe_stop_tx in ice_tx_map is passed a value that is >= the value
that was used on the initial call to ice_maybe_stop_tx in
ice_xmit_frame_ring. This was done by adding the following defines to
make the logic more clear and to reduce the chance of mucking this up
again:
ICE_CACHE_LINE_BYTES 64
ICE_DESCS_PER_CACHE_LINE (ICE_CACHE_LINE_BYTES / \
sizeof(struct ice_tx_desc))
ICE_DESCS_FOR_CTX_DESC 1
ICE_DESCS_FOR_SKB_DATA_PTR 1
The ICE_CACHE_LINE_BYTES being 64 is an assumption being made so we
don't have to figure this out on every pass through the Tx path. Instead
I added a sanity check in ice_probe to verify cache line size and print
a message if it's not 64 Bytes. This will make it easier to file issues
if they are seen when the cache line size is not 64 Bytes when reading
from the GLPCI_CNF2 register.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the remove path, the vsi->netdev is being set to NULL before the call
to free vectors. This is causing the netif_napi_del call to never be made.
Add a call to ice_napi_del to the same location as the calls to
unregister_netdev and just prior to them. This will use the reverse flow
as the register and netif_napi_add calls.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Print should say "Enabling" instead of "Enaabling"
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to the spec, whenever insert PVID field is set, the VLAN
driver insertion mode should be set to 01b which isn't done currently.
Fix it.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_restore_vlan and active_vlans were originally put in place to
reprogram VLAN filters in the replay path. This is now done as part
of the much broader VSI rebuild/replay framework. So remove both
ice_restore_vlan and active_vlans
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the unload path, all VSIs are freed. Also free the related VSI
contexts to prevent memory leaks.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Setting Rx or Tx pause parameter currently results in link loss on the
interface, requiring the platform/host to be cold power cycled. Fix it.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The remove path does not currently check to see if a
reset is in progress before proceeding. This can cause
a resource collision resulting in various types of errors.
Check for reset in progress and wait for a reasonable
amount of time before allowing the remove to progress.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the carrier state post rebuild by querying the link status. Also
start/stop queues based on link status.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change resolves a driver bug where the driver is logging a
message that says "Spoofed packets detected". This can occur on the PF
(host) when a VF has VLAN+MACVLAN enabled and is re-started with a
different MAC address.
MAC and VLAN anti-spoofing filters are to be enabled together.
Signed-off-by: Radoslaw Tyl <radoslawx.tyl@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Acked-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a few new status code which will be used by the ice driver, and
rename a few to make them more consistent. Error code are mapped to
similar values as in i40e_status.h, so as to be compatible with older
VF drivers not using this status enum.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original work from Arnd Bergmann.
When XFRM_ALGO is not enabled, the new ixgbe IPsec code produces a
link error:
drivers/net/ethernet/intel/ixgbe/ixgbe_ipsec.o: In function `ixgbe_ipsec_vf_add_sa':
ixgbe_ipsec.c:(.text+0x1266): undefined reference to `xfrm_aead_get_byname'
Simply selecting XFRM_ALGO from here causes circular dependencies, so
to fix it, we probably want this slightly more complex solution that is
similar to what other drivers with XFRM offload do:
A separate Kconfig symbol now controls whether we include the IPsec
offload code. To keep the old behavior, this is left as 'default y'. The
dependency in XFRM_OFFLOAD still causes a circular dependency but is
not actually needed because this symbol is not user visible, so removing
that dependency on top makes it all work.
CC: Arnd Bergmann <arnd@arndb.de>
CC: Shannon Nelson <shannon.nelson@oracle.com>
Fixes: eda0333ac2 ("ixgbe: add VF IPsec management")
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
The upstream and out-of-tree drivers are once again at comparable
functionality. It's been a while since we updated the upstream driver
version, so bump it now.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device IDs for the Ethernet SDI Adapter devices were never added to
the upstream driver. The IDs are already in the pci.ids database, and
are supported by the out-of-tree driver.
Add the device IDs now, so that the upstream driver can recognize and
load these devices.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF drivers can trigger PCIe completer aborts any time they read a queue
that they don't own. Even in nominal circumstances, it is not possible
to prevent the VF driver from reading queues it doesn't own. VF drivers
may attempt to read queues it previously owned, but which it no longer
does due to a PF reset.
Normally these completer aborts aren't an issue. However, on some
platforms these trigger machine check errors. This is true even if we
lower their severity from fatal to non-fatal. Indeed, we already have
code for lowering the severity.
We could attempt to mask these errors conditionally around resets, which
is the most common time they would occur. However this would essentially
be a race between the PF and VF drivers, and we may still occasionally
see machine check exceptions on these strictly configured platforms.
Instead, mask the errors entirely any time we resume VFs. By doing so,
we prevent the completer aborts from being sent to the parent PCIe
device, and thus these strict platforms will not upgrade them into
machine check errors.
Additionally, we don't lose any information by masking these errors,
because we'll still report VFs which attempt to access queues via the
FUM_BAD_VF_QACCESS errors.
Without this change, on platforms where completer aborts cause machine
check exceptions, the VF reading queues it doesn't own could crash the
host system. Masking the completer abort prevents this, so we should
mask it for good, and not just around a PCIe reset. Otherwise malicious
or misconfigured VFs could cause the host system to crash.
Because we are masking the error entirely, there is little reason to
also keep setting the severity bit, so that code is also removed.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Current condition will always incorrectly report a full SM mailbox if an
IES API application is not running. Due to this, the
"fm10k_service_task" will be infinitely queued into the driver's
workqueue. This, in turn, will cause a "kworker" thread to report 100%
CPU utilization and might cause "soft lockup" events or system crashes.
To fix this issue, a new condition is added to determine if the SM
mailbox is in the correct state of FM10K_STATE_OPEN before proceeding.
In other words, an instance of the IES API must be running. If there is,
the remainder of the flow stays the same which is to determine if the SM
mailbox capacity has been exceeded or not and take appropriate action.
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The timecounter needs to be updated at least once per ~550 seconds in
order to avoid a 40-bit SYSTIM timestamp to be misinterpreted as an old
timestamp.
Since commit 500462a9d ("timers: Switch to a non-cascading wheel"),
scheduling of delayed work seems to be less accurate and a requested
delay of 540 seconds may actually be longer than 550 seconds. Shorten
the delay to 480 seconds to be sure the timecounter is updated in time.
This fixes an issue with HW timestamps on 82580/I350/I354 being off by
~1100 seconds for few seconds every ~9 minutes.
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking fixes from David Miller:
"What better way to start off a weekend than with some networking bug
fixes:
1) net namespace leak in dump filtering code of ipv4 and ipv6, fixed
by David Ahern and Bjørn Mork.
2) Handle bad checksums from hardware when using CHECKSUM_COMPLETE
properly in UDP, from Sean Tranchetti.
3) Remove TCA_OPTIONS from policy validation, it turns out we don't
consistently use nested attributes for this across all packet
schedulers. From David Ahern.
4) Fix SKB corruption in cadence driver, from Tristram Ha.
5) Fix broken WoL handling in r8169 driver, from Heiner Kallweit.
6) Fix OOPS in pneigh_dump_table(), from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (28 commits)
net/neigh: fix NULL deref in pneigh_dump_table()
net: allow traceroute with a specified interface in a vrf
bridge: do not add port to router list when receives query with source 0.0.0.0
net/smc: fix smc_buf_unuse to use the lgr pointer
ipv6/ndisc: Preserve IPv6 control buffer if protocol error handlers are called
net/{ipv4,ipv6}: Do not put target net if input nsid is invalid
lan743x: Remove SPI dependency from Microchip group.
drivers: net: remove <net/busy_poll.h> inclusion when not needed
net: phy: genphy_10g_driver: Avoid NULL pointer dereference
r8169: fix broken Wake-on-LAN from S5 (poweroff)
octeontx2-af: Use GFP_ATOMIC under spin lock
net: ethernet: cadence: fix socket buffer corruption problem
net/ipv6: Allow onlink routes to have a device mismatch if it is the default route
net: sched: Remove TCA_OPTIONS from policy
ice: Poll for link status change
ice: Allocate VF interrupts and set queue map
ice: Introduce ice_dev_onetime_setup
net: hns3: Fix for warning uninitialized symbol hw_err_lst3
octeontx2-af: Copy the right amount of memory
net: udp: fix handling of CHECKSUM_COMPLETE packets
...
Drivers using generic NAPI interface no longer need to include
<net/busy_poll.h>, since busy polling was moved to core networking
stack long ago.
See commit 79e7fff47b ("net: remove support for per driver
ndo_busy_poll()") for reference.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
When the physical link goes up or down, the driver is supposed to
receive a link status event (LSE). The driver currently has the code
to handle LSEs but there is no firmware support for this feature yet.
So this patch adds the ability for the driver to poll for link status
changes. The polling itself is done in ice_watchdog_subtask.
For namespace cleanliness, this patch also removes code that handles
LSE. This code will be reintroduced once the feature is officially
supported.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Allocate VF interrupts using VPINT_ALLOC_PCI. Multiple interrupts are
specified as a range from "first" to "last".
Also, according to the spec, the queue mapping for a VF needs to be set
in both contig and scatter queue modes. So make this change as well.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_dev_onetime_setup contains a couple of driver workarounds for current
firmware limitations. These workarounds are expected to go away once
these limitations are fixed in the firmware.
On a firmware release that has these issues addressed, these workarounds
(while unnecessary) will not break anything.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware now returns the capability count in the command buffer.
Use it.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update to the current firmware major and minor version which are
1 and 3 respectively.
Also remove an empty comment line.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Basically remove references to C810 and use E810C (from the branding
string) instead.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
commit 158a08a694 ("ice: remove ndo_poll_controller") removed
ice_netpoll and introduced a namespace warning for ice_msix_clean_rings.
Fix the namespace warning by making ice_msix_clean_rings static.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that the documents have been updated to conform to the reStructured Text
guidelines, we can now change the file extensions and update the other
related references.
This converts all of the Intel wired LAN driver documentation to *.rst.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Added the fm10k kernel documentation, which apparently was missing.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Add link establishment methods
Add auto negotiation methods
Add read MAC address method
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add PHY's ID support
Add support for initialization, acquire and release of PHY
Enable register access
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code for NVM support and get MAC address, complete probe
method.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add code for hardware initialization and reset
Add code for semaphore handling
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for allocating, configuring, and freeing Tx/Rx ring
resources. With these changes in place the descriptor queues are in a
state where they are ready to transmit or receive if provided buffers.
This also adds the transmit and receive fastpath and interrupt handlers.
With this code in place the network device is now able to send and receive
frames over the network interface using a single queue.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change adds the defines and structures necessary to support both Tx
and Rx descriptor rings.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch set adds interrupt support for the igc interfaces.
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
