The build servers and linux-next are complaining like this:
drivers/gpio/gpio-amd-fch.c: In function 'amd_fch_gpio_probe':
drivers/gpio/gpio-amd-fch.c:164:49: warning: passing argument 2 of
'devm_ioremap_resource' discards 'const' qualifier from pointer
target type [-Wdiscarded-qualifiers]
priv->base = devm_ioremap_resource(&pdev->dev, &amd_fch_gpio_iores);
^~~~~~~~~~~~~~~~~~~
In file included from include/linux/platform_device.h:14, from
drivers/gpio/gpio-amd-fch.c:15:
include/linux/device.h:709:15: note: expected 'struct resource *'
but argument is of type 'const struct resource *'
void __iomem *devm_ioremap_resource(struct device *dev,struct resource *res);
^~~~~~~~~~~~~~~~~~~~~
Let's just remove "const" for now.
It is possible that devm_ioremap_resource() should rather
be constified so we can pass const resources as arguments.
But right now I just want to get rid of this build warning.
Fixes: e09d168f13 ("gpio: AMD G-Series PCH gpio driver")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Cc: Enrico Weigelt <info@metux.net>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On i.MX8MQ platform, clock driver uses platform driver
model and it is probed after GPIO driver, so when GPIO
driver fails to get clock, it should check the error type
to decide whether to return defer probe or just ignore
the clock operation.
Fixes: 2808801aab ("gpio: mxc: add clock operation")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This augments the FTGPIO010 to register one irqchip
per instance instead of using a static definition.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
GPIO platform driver for the AMD G-series PCH (eg. on GX-412TC)
This driver doesn't registers itself automatically, as it needs to
be provided with platform specific configuration, provided by some
board driver setup code.
Didn't implement oftree probing yet, as it's rarely found on x86.
Cc: linux-gpio@vger.kernel.org
Cc: linus.walleij@linaro.org
Cc: bgolaszewski@baylibre.com
Cc: dvhart@infradead.org
Cc: platform-driver-x86@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For output-only gpios, direction_output should set proper output level.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change to use SoC compatible string instead of wildcard string.
The Spreadtrum SC9860 platform device trees and drivers' development
are still in progress, and now we will always recompile and ship
device trees at the same time as we will compile and ship the kernel,
so we do not need care about the backwards compatibility.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Handle both enable-gpio and enable-gpios properties of the GPIO
regulator in the quirk. The later is the preferred modern name
of the property.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Jan Kotas <jank@cadence.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: linux-renesas-soc@vger.kernel.org
To: linux-gpio@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 0e7d6f9401 ("gpio: of: Apply regulator-gpio quirk only to
enable-gpios") breaks the device tree ABI specified in the device tree
bindings for fixed regulators (compatible "regulator-fixed"). According
to these bindings the polarity of the GPIO is exclusively controlled by
the presence or absence of the enable-active-high property. As such the
polarity quirk implemented in of_gpio_flags_quirks() must be applied to
the GPIO specified for fixed regulators.
However, commit 0e7d6f9401 ("gpio: of: Apply regulator-gpio quirk only
to enable-gpios") restricted the quirk to the enable-gpios property for
fixed regulators as well, whereas according to the commit message itself
it should only apply to "regulator-gpio" compatible device tree nodes.
Fix this by actually implementing what the offending commit intended,
which is to ensure that the quirk is applied to the GPIO specified by
the "enable-gpio" property for the "regulator-gpio" bindings only.
This fixes a regression on Jetson TX1 where the fixed regulator for the
HDMI +5V pin relies on the flags quirk for the proper polarity.
Fixes: 0e7d6f9401 ("gpio: of: Apply regulator-gpio quirk only to enable-gpios")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the new helper that wraps the calls to platform_get_resource() and
devm_ioremap_resource() together.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement the irq_set_wake() method in the (optional) irq_chip of the
GPIO expander, and propagate wake-up settings to the upstream interrupt
controller. This allows GPIOs connected to a PCA953X GPIO expander to
serve as wake-up sources.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- gpio-mockup updates improving the user-space testing interface and
adding line state tracking for correct edge interrupts
- interrupt simulator patch exposing the irq type configuration to
users
-----BEGIN PGP SIGNATURE-----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=mEAi
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-updates-for-linus-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: updates for v5.1 - part 2
- gpio-mockup updates improving the user-space testing interface and
adding line state tracking for correct edge interrupts
- interrupt simulator patch exposing the irq type configuration to
users
This patch hunk is a lightly modified version of a diff found
in a Tegra code dump from a product tree. It makes a lot of
sense because this is what most drivers do.
Cc: Thierry Reding <treding@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Dmitry Osipenko <digetx@gmail.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Modify the way the debugfs interface works in gpio-mockup. Introduce
the concept of dummy pull config which will keep the mockup lines in
known state. The pull values can be modified by writing to the debugfs
files corresponding to lines. Lines in input mode always report the
current pull value, lines in output mode change the line value but
it will revert back to the one specified by current pull when released.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The unlocked variants only get called from places where we already have
the pointer to the underlying gpio_mockup_chip structure, so take it
as parameter instead of struct gpio_chip.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
While no user reported any race condition problems with gpio-mockup,
let's be on the safe side and use a mutex when performing any changes
on the dummy chip structures.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Since commit d6cd33ad71 ("regulator: gpio: Convert to use descriptors")
the GPIO regulator had inverted the polarity of the control GPIO. This
problem manifested itself on systems with DT containing the following
description (snippet from salvator-common.dtsi):
gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
gpios-states = <1>;
states = <3300000 1
1800000 0>;
Prior to the aforementioned commit, the gpio-regulator code used
gpio_request_array() to claim the GPIO(s) specified in the "gpios"
DT node, while the commit changed that to devm_gpiod_get_index().
The legacy gpio_request_array() calls gpio_request_one() and then
gpiod_request(), which parses the DT flags of the "gpios" node and
populates the GPIO descriptor flags field accordingly.
The new devm_gpiod_get_index() calls gpiod_get_index(), then
of_find_gpio(), of_get_named_gpiod_flags() with flags != NULL,
and then of_gpio_flags_quirks(). Since commit a603a2b8d8
("gpio: of: Add special quirk to parse regulator flags"),
of_gpio_flags_quirks() contains a quirk for regulator-gpio
which was never triggered by the legacy gpio_request_array()
code path, but is triggered by devm_gpiod_get_index() code
path.
This quirk checks whether a GPIO is associated with a fixed
or gpio-regulator and if so, checks two additional conditions.
First, whether such GPIO is active-low, and if so, ignores the
active-low flag. Second, whether the regulator DT node does
have an "enable-active-high" property and if the property is
NOT present, sets the GPIO flags as active-low.
The second check triggers a problem, since it is applied to all
GPIOs associated with a gpio-regulator, rather than only on the
"enable" GPIOs, as the old code did. This changes the way the
gpio-regulator interprets the DT description of the control
GPIOs.
The old code using gpio_request_array() explicitly parsed the
"enable-active-high" DT property and only applied it to the
GPIOs described in the "enable-gpios" DT node, and only if
those were present.
This patch fixes the quirk code by only applying the quirk
to "enable-gpios", thus restoring the old behavior.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Jan Kotas <jank@cadence.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Wolfram Sang <wsa+renesas@sang-engineering.com>
Cc: linux-renesas-soc@vger.kernel.org
To: linux-gpio@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Small clean up for Intel PMIC GPIO drivers, includes:
- optimizing IRQ handlers by usage of for_each_set_bit()
- sorting headers alphabetically for better maintenance
- conversion to SPDX identifier
The following is an automated git shortlog grouped by driver:
crystalcove:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Use for_each_set_bit() in IRQ handler
msic:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Remove duplicate check in IRQ handler
wcove:
- Convert to use SPDX identifier
- Fix indentation
- Sort headers alphabetically
- Allow return negative error code from to_reg()
-----BEGIN PGP SIGNATURE-----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=ScJF
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v5.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel
intel-gpio for v5.1-1
Small clean up for Intel PMIC GPIO drivers, includes:
- optimizing IRQ handlers by usage of for_each_set_bit()
- sorting headers alphabetically for better maintenance
- conversion to SPDX identifier
The following is an automated git shortlog grouped by driver:
crystalcove:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Use for_each_set_bit() in IRQ handler
msic:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Remove duplicate check in IRQ handler
wcove:
- Convert to use SPDX identifier
- Fix indentation
- Sort headers alphabetically
- Allow return negative error code from to_reg()
- support for a new variant of pca953x
- documentation fix from Wolfram
- some tegra186 name changes
- two minor fixes for madera and altera-a10sr
-----BEGIN PGP SIGNATURE-----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=nV64
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.1-updates-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.1
- support for a new variant of pca953x
- documentation fix from Wolfram
- some tegra186 name changes
- two minor fixes for madera and altera-a10sr
Change the coding style to make it does error checking first.
This also fixes checkpatch warning about line over 80 characters.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The new prefix allows the GPIOs to be uniquely identified on a per-chip
basis, which makes it easier to distinguish Tegra186 specific GPIOs from
those of later chips such as Tegra194 which supports a very different
set of GPIOs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
madera_gpio_chip is only used as a template so it can be marked as const.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The NXP PCAL6416, documented at [1], is a variant of the PCA GPIO
expander with 16 GPIOs, and supporting an interrupt and the "extended"
features for interrupt, pull-up/pull-down configuration, etc.
[1] https://www.nxp.com/docs/en/data-sheet/PCAL6416A.pdf
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Similarly to PXA3xx, pinctrl-single can't set pin direction on MMP2 either.
See also: commit 9dabfdd84b ("gpio: pxa: disable pinctrl calls for
PXA3xx")
Cc: stable@vger.kernel.org
Fixes: a770d94637 ("gpio: pxa: add pin control gpio direction and request")
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Unlike gpio_rcar_irq_set_wake(), which this solution was based on,
pcf857x_irq_set_wake() does not need to do anything else than calling
irq_set_irq_wake() for the upstream interrupt controller. Hence there
is no reason for making this call conditional, and no longer a need for
keeping a copy of the interrupt number that also serves as a flag.
Just propagate irq_set_irq_wake() to the upstream interrupt controller,
using the original interrupt number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following warning by adding a missing break:
drivers/gpio/gpio-eic-sprd.c: In function ‘sprd_eic_irq_set_type’:
drivers/gpio/gpio-eic-sprd.c:403:3: warning: this statement may fall through [-Wimplicit-fallthrough=]
switch (flow_type) {
^~~~~~
drivers/gpio/gpio-eic-sprd.c:435:2: note: here
default:
^~~~~~~
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Zynq GPIO driver currently implements runtime PM by:
- Enabling runtime PM support in ->probe() and letting the runtime PM
reference counter drop to zero at the end of ->probe().
- Increasing the runtime PM reference counter in ->request() and
decreasing it in ->free().
However, the latter is not sufficient: when a GPIO is used as an
interrupt, ->request() and ->free() are not called. Due to this, the
runtime PM counter remains to zero when the only GPIOs in use are used
as interrupts, causing them to simply not work.
To address this problem, this commit implement the
->irq_request_resources() and ->irq_release_resources() hooks,
ensuring that the runtime PM counter is properly
incremented/decremented. Since we override the default hooks, we keep
the existing behavior by making sure they call gpiochip_reqres_irq() /
gpiochip_relres_irq() respectively.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds a minimal implementation of the ->set_config() hook,
with support for the PIN_CONFIG_BIAS_PULL_UP and
PIN_CONFIG_BIAS_PULL_DOWN configurations.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds support for configuring the pull-up and pull-down
resistors available in some GPIO controllers. While configuring
pull-up/pull-down is already possible through the pinctrl subsystem,
some GPIO controllers, especially simple ones such as GPIO expanders
on I2C, don't have any pinmuxing capability and therefore do not use
the pinctrl subsystem.
This commit implements the GPIO_PULL_UP and GPIO_PULL_DOWN flags,
which can be used from the Device Tree, to enable a pull-up or
pull-down resistor on a given GPIO.
The flag is simply propagated all the way to the core GPIO subsystem,
where it is used to call the gpio_chip ->set_config callback with the
appropriate existing PIN_CONFIG_BIAS_* values.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As suggested by Linus Walleij, let's use the new gpio_set_config()
helper in gpiod_set_debounce() and gpiod_set_transitory().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit simply renames gpio_set_drive_single_ended() to
gpio_set_config(), as the function is not specific to setting the GPIO
drive type, and will be used for other purposes in followup commits.
In addition, it moves the function above gpiod_direction_input(), as
it will be used from gpiod_direction_input().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Interupts were generated using GPIN interrupts of
ADP5588. These interrupts have two important limitations:
1. Interrupts can only be generated for either rising or
falling edges but not both.
2. Interrupts are reasserted as long as the interrupt condition
persists (i.e. high or low level on that GPIN). This generates
lots of interrupts unless the event is very short.
To overcome this, ADP5588 provides an event system which queues
up to 10 events in a buffer. GPIN events are queued whenever the
GPIN is asserted or deasserted. This makes it possible to support
generating GPIN interrupts for both edges and to generate only one
interrupt per state change.
Thus it is possible to chain the gpio-keys driver for some GPIOs.
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make platform data optional and add DT id table.
Switch to dynamically mapped GPIOs and IRQs if not provided
via platform data.
Signed-off-by: Nikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's not necessary to remove gpio_chip which added with
devm_gpiochip_add_data().
Fixes: b868db94a6 ("gpio: tqmx86: Add GPIO from for this IO controller")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver for Gateworks PLD GPIO, that exist in
two instances on the Gateworks Cambria GW2358-4 router
platform at least.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New quirk enforces search for GPIO based on its type,
i.e. iterate over GpioIo resources only.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
There is no need to check for non-zero pending since for_each_set_bit() does it
on the first iteration.
While here, drop redundant assignment.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The type of to_reg() is unsigned int while it might return
a negative error code. Callers are also expecting a signed type.
For sake of type consistency replace unsigned int with plain int.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This simplifies and standardizes the AB IRQ handler by using
the for_each_set_bit() library function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
This fixes the kernel complains:
gpio gpiochip1: (1e000600.gpio-bank1): detected irqchip that is shared
with multiple gpiochips: please fix the driver.
gpio gpiochip2: (1e000600.gpio-bank2): detected irqchip that is shared
with multiple gpiochips: please fix the driver.
Fixes: 4ba9c3afda ("gpio: mt7621: Add a driver for MT7621")
Cc: stable@vger.kernel.org
Signed-off-by: René van Dorst <opensource@vdorst.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Tested-by: Greg Ungerer <gerg@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the Rohm Vendor ID to pci_ids.h instead of defining it in several
drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
On SoC reset all GPIO interrupts are disable. However, if kexec is
used to boot into a new kernel, the SoC does not experience a
reset. Hence GPIO interrupts can be left enabled from the previous
kernel. It is then possible for the interrupt to fire before an
interrupt handler is registered, resulting in the kernel complaining
of an "unexpected IRQ trap", the interrupt is never cleared, and so
fires again, resulting in an interrupt storm.
Disable all GPIO interrupts before registering the GPIO IRQ chip.
Fixes: 7f2691a196 ("gpio: vf610: add gpiolib/IRQ chip driver for Vybrid")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The checker complains during build
gpiolib-acpi.c:45: warning: Function parameter or member 'irq_requested' not described in 'acpi_gpio_event'
because the typo in the field description.
Fix the name to have documentation up-to-date.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some TQ-Systems ComExpress modules contain an IO controller with 8
GPIO lines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add missing '*' char to the start of the comment lines.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI chip selects were not properly inspected due to
a logic inversion. This made SPI GPIOs not work.
Cc: Jan Kotas <jank@cadence.com>
Reported-by: Jan Kotas <jank@cadence.com>
Tested-by: Jan Kotas <jank@cadence.com>
Fixes: f3186dd876 ("spi: Optionally use GPIO descriptors for CS GPIOs")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds the two new functions gpiochip_irq_domain_activate and
gpiochip_irq_domain_deactivate that can be used as the activate and
deactivate functions in the struct irq_domain_ops. This is for
situations where only gpiochip_{lock,unlock}_as_irq needs to be called.
SPMI and SSBI GPIO are two users that will initially use these
functions.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The altr_a10sr_gpio_direction_output should set proper output level
based on the value argument.
Fixes: 26a48c4cc2 ("gpio: altera-a10sr: Add A10 System Resource Chip GPIO support.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Tested by: Thor Thayer <thor.thayer@linux.intel.com>
Reviewed by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When setting async EIC as IRQ_TYPE_EDGE_BOTH type, we missed to set the
SPRD_EIC_ASYNC_INTMODE register to 0, which means detecting edge signals.
Thus this patch fixes the issue.
Fixes: 25518e024e ("gpio: Add Spreadtrum EIC driver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Neo Hou <neo.hou@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Since differnt type EICs have its own data register to read, thus fix the
incorrect data register.
Fixes: 25518e024e ("gpio: Add Spreadtrum EIC driver support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Neo Hou <neo.hou@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Nested interrupts run inside the calling thread's context and the top
half handler is never called which means that we never read the
timestamp.
This issue came up when trying to read line events from a gpiochip
using regmap_irq_chip for interrupts.
Fix it by reading the timestamp from the irq thread function if it's
still 0 by the time the second handler is called.
Fixes: d58f2bf261 ("gpio: Timestamp events in hardirq handler")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When multiple instances of pcf857x chips are present, a fix up
message [1] is printed during the probe of the 2nd and later
instances.
The issue is that the driver is using the same irq_chip data
structure between multiple instances.
Fix this by allocating the irq_chip data structure per instance.
[1] fix up message addressed by this patch
[ 1.212100] gpio gpiochip9: (pcf8575): detected irqchip that is shared with multiple gpiochips: please fix the driver.
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Basic implementation of driver is used to support Fintek
F81804 & F81966 gpios with custom register set.
Signed-off-by: Steffen Kothe <steffen.kothe.gc1993@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
R-Car GPIO controller provides two interfaces to set GPIO line output
signal state, and for a particular GPIO line the selected interface is
determined by OUTDTSEL bit value.
At the moment the driver supports only one of two interfaces, namely
OUTDT General Output Register is used to control the output signal.
While this selection is the default one on reset, it is not explicitly
configured on probe, thus it might be possible that kernel and userspace
consumers of a GPIO won't be able to set the wanted GPIO output signal.
Below is a simple test case to reproduce the described problem and
verify this fix in the kernel on H3 ULCB by setting non-default OUTDTSEL
configuration from a bootloader:
u-boot > mw.l 0xe6055440 0x3000 1
...
userspace > echo default-on > /sys/devices/platform/leds/leds/led5/trigger
userspace > echo default-on > /sys/devices/platform/leds/leds/led6/trigger
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Like the Spreadtrum EIC driver[1], this driver needs to emulate edge
triggered interrupts to support the generic gpio-keys driver.
[1]: https://www.spinics.net/lists/kernel/msg2764576.html
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch implements level-triggered IRQs in the Hollywood GPIO driver.
Edge triggered interrupts are not supported in this GPIO controller, so
I moved their emulation into a separate patch.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a system has two PCA953x GPIO expanders, the kernel complains with:
gpio gpiochip2: (0-0021): detected irqchip that is shared with multiple gpiochips: please fix the driver.
Indeed, there is a single instance of "struct irq_chip" that gets
re-used for both PCA953x instance. This commit moves the "struct
irq_chip" to be part of the "struct pca953x_chip", so that we have one
"struct irq_chip" per PCA953X instance.
As part of this, the name of the irq_chip is also made different on a
per-instance basis, now using the dev_name() of the I2C device. This
changes what is visible in /proc/interrupts.
Before:
47: 0 0 pca953x 10 Edge e0100000.sdhci cd
48: 0 0 pca953x 6 Edge e0101000.sdhci cd
After:
47: 0 0 0-0020 10 Edge e0100000.sdhci cd
48: 2 0 0-0020 6 Edge e0101000.sdhci cd
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The current design of pca953x_irq_setup() is:
if (all conditions to support IRQ are met) {
lots of code to support IRQs, which goes to a serious indentation
level.
}
return 0;
It makes more sense to handle this like this:
if (!all conditions to support IRQ are met)
return 0;
handle IRQ support
This commit does just this change, reducing by one tab the indentation
level of the IRQ setup code. Thanks to this reduced indentation level,
we are less restricted by the 80-column limit, and we can have more
function arguments on the same line.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Spreadtrum PMIC interrupt controller has no registers to set irq
trigger type, since it is always high level trigger. That means the
PMIC EIC controller as a child device of PMIC INTC does not need to
set the trigger type, so remove it.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set proper output level base on the argument of direction_output.
Also remove sama5d2_piobu_set_direction() as there is only one caller
now.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes the following sparse warning:
drivers/gpio/gpio-pca953x.c:292:28: warning:
symbol 'pca953x_i2c_regmap' was not declared. Should it be static?
Fixes: 4942723276 ("gpio: pca953x: Perform basic regmap conversion")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
__acpi_gpio_update_gpiod_flags purpose is to make the gpiod_flags used
when requesting a GPIO match the restrictions from the ACPI resource,
as stored in acpi_gpio_info.flags.
But acpi_gpio_info.flags only contains direction info, and the
requester may have passed in special non-direction flags like
GPIOD_FLAGS_BIT_NONEXCLUSIVE, which we currently clobber.
This commit modifies __acpi_gpio_update_gpiod_flags to preserve these
special flags, so that a requested of an ACPI GPIO can e.g. pass
GPIOD_FLAGS_BIT_NONEXCLUSIV and have it work as intended.
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct gpio_chip documentation recommends to always implement this
callback function.
A more concrete motivation is to be able (in combination with
GPIOD_ASIS) to detect whether the bootloader has changed the state of a
GPIO signal.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
acpi_gpiochip_alloc_event only continues allocating an event and adding
it to the list if gpiochip_request_own_desc does not return an error.
So events with an error desc are never placed on the events list and this
check is really not necessary.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Some core changes are already in outside of this pull
request as they came through the regulator tree, most
notably devm_gpiod_unhinge() that removes devres refcount
management from a GPIO descriptor. This is needed in
subsystems such as regulators where the regulator core
need to take over the reference counting and lifecycle
management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match()
as nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This
helps setting the direction now that we are two GPIO
maintainers.
- Handle the MMC CD/WP properties in the device tree core.
(The bulk of patches activating this code is already
merged through the MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so
we as gpiochips can request lines as active low or open
drain etc even from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has
been around for ages, and is now modernized to reduce code
duplication that has stacked up and is using regmap to read
write and cache registers.
- Intel drivers are now maintained in a separate tree and
start with a round of cleanups and unifications.
-----BEGIN PGP SIGNATURE-----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=05LW
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.21 kernel series.
Core changes:
- Some core changes are already in outside of this pull request as
they came through the regulator tree, most notably
devm_gpiod_unhinge() that removes devres refcount management from a
GPIO descriptor. This is needed in subsystems such as regulators
where the regulator core need to take over the reference counting
and lifecycle management for a GPIO descriptor.
- We dropped devm_gpiochip_remove() and devm_gpio_chip_match() as
nothing needs it. We can bring it back if need be.
- Add a global TODO so people see where we are going. This helps
setting the direction now that we are two GPIO maintainers.
- Handle the MMC CD/WP properties in the device tree core. (The bulk
of patches activating this code is already merged through the
MMC/SD tree.)
- Augment gpiochip_request_own_desc() to pass a flag so we as
gpiochips can request lines as active low or open drain etc even
from ourselves.
New drivers:
- New driver for Cadence GPIO blocks.
- New driver for Atmel SAMA5D2 PIOBU GPIO lines.
Driver improvements:
- A major refactoring of the PCA953x driver - this driver has been
around for ages, and is now modernized to reduce code duplication
that has stacked up and is using regmap to read write and cache
registers.
- Intel drivers are now maintained in a separate tree and start with
a round of cleanups and unifications"
* tag 'gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (99 commits)
gpio: sama5d2-piobu: Depend on OF_GPIO
gpio: Add Cadence GPIO driver
dt-bindings: gpio: Add bindings for Cadence GPIO
gpiolib-acpi: remove unused variable 'err', cleans up build warning
gpio: mxs: read pin level directly instead of using .get
gpio: aspeed: remove duplicated statement
gpio: add driver for SAMA5D2 PIOBU pins
dt-bindings: arm: atmel: describe SECUMOD usage as a GPIO controller
gpio/mmc/of: Respect polarity in the device tree
dt-bindings: gpio: rcar: Add r8a774c0 (RZ/G2E) support
memory: omap-gpmc: Get the header of the enum
ARM: omap1: Fix new user of gpiochip_request_own_desc()
gpio: pca953x: Add regmap dependency for PCA953x driver
gpio: raspberrypi-exp: decrease refcount on firmware dt node
gpiolib: Fix return value of gpio_to_desc() stub if !GPIOLIB
gpio: pca953x: Restore registers after suspend/resume cycle
gpio: pca953x: Zap single use of pca953x_read_single()
gpio: pca953x: Zap ad-hoc reg_output cache
gpio: pca953x: Zap ad-hoc reg_direction cache
gpio: pca953x: Perform basic regmap conversion
...
- Cleanup BKOPS support
- Introduce MMC_CAP_SYNC_RUNTIME_PM
- slot-gpio: Delete legacy slot GPIO handling
MMC host:
- alcor: Add new mmc host driver for Alcor Micro PCI based cardreader
- bcm2835: Several improvements to better recover from errors
- jz4740: Rework and fixup pre|post_req support
- mediatek: Add support for SDIO IRQs
- meson-gx: Improve clock phase management
- meson-gx: Stop descriptor on errors
- mmci: Complete the sbc error path by sending a stop command
- renesas_sdhi/tmio: Fixup reset/resume operations
- renesas_sdhi: Add support for r8a774c0 and R7S9210
- renesas_sdhi: Whitelist R8A77990 SDHI
- renesas_sdhi: Fixup eMMC HS400 compatibility issues for H3 and M3-W
- rtsx_usb_sdmmc: Re-work card detection/removal support
- rtsx_usb_sdmmc: Re-work runtime PM support
- sdhci: Fix timeout loops for some variant drivers
- sdhci: Improve support for error handling due to failing commands
- sdhci-acpi/pci: Disable LED control for Intel BYT-based controllers
- sdhci_am654: Add new SDHCI variant driver to support TI's AM654 SOCs
- sdhci-of-esdhc: Add support for eMMC HS400 mode
- sdhci-omap: Fixup reset support
- sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures
- sdhci-msm: Fixup sporadic write transfers issues for SDR104/HS200
- sdhci-msm: Fixup dynamical clock gating issues
- various: Complete converting all hosts into using slot GPIO descriptors
Other:
- Move GPIO mmc platform data for mips/sh/arm to GPIO descriptors
- Add new Alcor Micro cardreader PCI driver
- Support runtime power management for memstick rtsx_usb_ms driver
- Use USB remote wakeups for card detection for rtsx_usb misc driver
-----BEGIN PGP SIGNATURE-----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=mB5P
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"This time, this pull request contains changes crossing subsystems and
archs/platforms, which is mainly because of a bigger modernization of
moving from legacy GPIO to GPIO descriptors for MMC (by Linus
Walleij).
Additionally, once again, I am funneling changes to
drivers/misc/cardreader/* and drivers/memstick/* through my MMC tree,
mostly due to that we lack a maintainer for these.
Summary:
MMC core:
- Cleanup BKOPS support
- Introduce MMC_CAP_SYNC_RUNTIME_PM
- slot-gpio: Delete legacy slot GPIO handling
MMC host:
- alcor: Add new mmc host driver for Alcor Micro PCI based cardreader
- bcm2835: Several improvements to better recover from errors
- jz4740: Rework and fixup pre|post_req support
- mediatek: Add support for SDIO IRQs
- meson-gx: Improve clock phase management
- meson-gx: Stop descriptor on errors
- mmci: Complete the sbc error path by sending a stop command
- renesas_sdhi/tmio: Fixup reset/resume operations
- renesas_sdhi: Add support for r8a774c0 and R7S9210
- renesas_sdhi: Whitelist R8A77990 SDHI
- renesas_sdhi: Fixup eMMC HS400 compatibility issues for H3 and M3-W
- rtsx_usb_sdmmc: Re-work card detection/removal support
- rtsx_usb_sdmmc: Re-work runtime PM support
- sdhci: Fix timeout loops for some variant drivers
- sdhci: Improve support for error handling due to failing commands
- sdhci-acpi/pci: Disable LED control for Intel BYT-based controllers
- sdhci_am654: Add new SDHCI variant driver to support TI's AM654 SOCs
- sdhci-of-esdhc: Add support for eMMC HS400 mode
- sdhci-omap: Fixup reset support
- sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures
- sdhci-msm: Fixup sporadic write transfers issues for SDR104/HS200
- sdhci-msm: Fixup dynamical clock gating issues
- various: Complete converting all hosts into using slot GPIO descriptors
Other:
- Move GPIO mmc platform data for mips/sh/arm to GPIO descriptors
- Add new Alcor Micro cardreader PCI driver
- Support runtime power management for memstick rtsx_usb_ms driver
- Use USB remote wakeups for card detection for rtsx_usb misc driver"
* tag 'mmc-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (99 commits)
mmc: mediatek: Add MMC_CAP_SDIO_IRQ support
mmc: renesas_sdhi_internal_dmac: Whitelist r8a774c0
dt-bindings: mmc: renesas_sdhi: Add r8a774c0 support
mmc: core: Cleanup BKOPS support
mmc: core: Drop redundant check in mmc_send_hpi_cmd()
mmc: sdhci-omap: Workaround errata regarding SDR104/HS200 tuning failures (i929)
dt-bindings: sdhci-omap: Add note for cpu_thermal
mmc: sdhci-acpi: Disable LED control for Intel BYT-based controllers
mmc: sdhci-pci: Disable LED control for Intel BYT-based controllers
mmc: sdhci: Add quirk to disable LED control
mmc: mmci: add variant property to set command stop bit
misc: alcor_pci: fix spelling mistake "invailid" -> "invalid"
mmc: meson-gx: add signal resampling
mmc: meson-gx: align default phase on soc vendor tree
mmc: meson-gx: remove useless lock
mmc: meson-gx: make sure the descriptor is stopped on errors
mmc: sdhci_am654: Add Initial Support for AM654 SDHCI driver
dt-bindings: mmc: sdhci-of-arasan: Add deprecated message for AM65
dt-bindings: mmc: sdhci-am654: Document bindings for the host controllers on TI's AM654 SOCs
mmc: sdhci-msm: avoid unused function warning
...
This has been a busy release for the regmap-irq code, there's several
new features been added, including an API cleanup for how we specify
types that affected one existing driver (gpio-max77620):
- Support for hardware that flags rising and falling edges on separate
status bits from Bartosz Golaszewski.
- Support for explicitly clearing interrupts before unmasking from
Bartosz Golaszewski.
- Support for level triggered IRQs from Matti Vaittinen.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwhMAUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0MI0B/9K27CbnGskQHZqWQxcFg1iVck/ZPty
kqfIGYDafvqT2TaVL+tFM8kzjLB3dMuV3cbywppq6+pzEvR/BDzhUKbskNPSLjUo
zNxKbwiBJPFLqlZORhzncuPcpRvrGGp120B+gr7lKOJgSG73u6bvOEzYaZbJzPb8
KiKo5oFqB/wpj3Gw243RjYE+7yaM/i7IAR/mW//RoKMWYERv6koR+GL0jgalib4d
mezH0ipO/SGDPorVOeUWxm/mlUYhEbitTa9+BtAYC/0+Nba1ns1p6dduchhXrAA0
/cOCHHVypPSiKLxjth+FA20CbemALb6swoZztVWYNS+0jJ2/bkh1rCoB
=aiDq
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"This has been a busy release for the regmap-irq code, there's several
new features been added, including an API cleanup for how we specify
types that affected one existing driver (gpio-max77620):
- Support for hardware that flags rising and falling edges on
separate status bits from Bartosz Golaszewski.
- Support for explicitly clearing interrupts before unmasking from
Bartosz Golaszewski.
- Support for level triggered IRQs from Matti Vaittinen"
* tag 'regmap-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: irq: add an option to clear status registers on unmask
regmap: regmap-irq/gpio-max77620: add level-irq support
regmap: regmap-irq: Remove default irq type setting from core
regmap: debugfs: convert to DEFINE_SHOW_ATTRIBUTE
regmap: rbtree: convert to DEFINE_SHOW_ATTRIBUTE
regmap: irq: handle HW using separate rising/falling edge interrupts
regmap: add a new macro:REGMAP_IRQ_REG_LINE(_id, _reg_bits)
This has been a very busy release for the core, some fixes, one large new
feature and a big bit of refactoring to update the GPIO API:
- Support for coupled regulators from Dmitry Osipenko based on a prior
attempt by Maciej Purski, allowing us to handle situations where the
voltages on two regulators can't be too far apart from each other.
- Conversion of the GPIO support in both drivers and the core to use
GPIO descriptors rather than numbers, part of the overall project to
remove GPIO numbers.
- Support for standby mode suspend states from Andrei Stefanescu.
- New drivers for Allwinner AXP209, Cirrus Logic Lochnagar and
Microchip MPC16502.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwhKkcTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DFfB/91/ECmybKTP+RvwUTZ0rrqFFs2C9Vl
76vH242exyJuzv44inWi9gOcXFDn7c9hf7Vl4Jd5UVP53Nzm5I8ZwExQsxax9BsN
hltlX01UpRAmHNkMNrnJH6YAntD3EicYGSUDjohkWItIDqpMAjhWpx/yGXTEjBir
gvkV51bF3qAYQe0g6MmK3KeVw96QPNjUhoPbsqbpaXaF6fmyOVzMiFrffJGmUAyM
J5qRv3OhsZiZy2/zxNLkUI6y4XKDEaFJ3RhSKoUwItGyKQt2saXMoJGyEEWm2b6X
coTm0ZQk+EU+b659lDHErTM4YUx7p7tQt3VM09NoMD8B261TdZ0y99Oh
=8Rxt
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"This has been a very busy release for the core, some fixes, one large
new feature and a big bit of refactoring to update the GPIO API:
- Support for coupled regulators from Dmitry Osipenko based on a
prior attempt by Maciej Purski, allowing us to handle situations
where the voltages on two regulators can't be too far apart from
each other.
- Conversion of the GPIO support in both drivers and the core to use
GPIO descriptors rather than numbers, part of the overall project
to remove GPIO numbers.
- Support for standby mode suspend states from Andrei Stefanescu.
- New drivers for Allwinner AXP209, Cirrus Logic Lochnagar and
Microchip MPC16502"
* tag 'regulator-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (90 commits)
regulator: tps65910: fix a missing check of return value
regulator: mcp16502: Select REGMAP_I2C to fix build error
regulator: convert to DEFINE_SHOW_ATTRIBUTE
regulator: mcp16502: Fix missing n_voltages setting
regulator: mcp16502: Use #ifdef CONFIG_PM_SLEEP around mcp16502_suspend/resume_noirq
regulator: mcp16502: code cleanup
regulator: act8945a-regulator: make symbol act8945a_pm static
drivers/regulator: fix a missing check of return value
regulator: act8945a-regulator: fix 'defined but not used' compiler warning
regulator: axp20x: fix set_ramp_delay for AXP209/dcdc2
regulator: mcp16502: add support for suspend
mfd: axp20x: use explicit bit defines
mfd: axp20x: Clean up included headers
regulator: dts: enable soft-start and ramp delay for the OLinuXino Lime2
dt-bindings: mfd: axp20x: Add software based soft_start for AXP209 LDO3
regulator: axp20x: add software based soft_start for AXP209 LDO3
dt-bindings: mfd: axp20x: add support for regulator-ramp-delay for AXP209
regulator: axp20x: add support for set_ramp_delay for AXP209
mfd: axp20x: name voltage ramping define properly
regulator: mcp16502: add regulator driver for MCP16502
...
This driver clearly needs OF_GPIO so depend on it.
Fixes a build error.
Cc: Andrei Stefanescu <Andrei.Stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- ACPI IRQ request deferral
- OMAP: revert deferred wakeup quirk
- MAX7301: fix DMA safe memory handling
- MVEBU: selective probe failure on missing clk
-----BEGIN PGP SIGNATURE-----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=+Iw2
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Hopefully last round of GPIO fixes.
The ACPI patch is pretty important for some laptop users, the rest is
driver-specific for embedded (mostly ARM) systems.
I took out one ACPI patch that wasn't critical enough because I
couldn't justify sending it at this point, and that is why the commit
date is today, but the patches have been in linux-next.
Sorry for not sending some of them earlier :(
Notice that we have a co-maintainer for GPIO now, Bartosz Golaszewski,
and he might jump in and make some pull requests at times when I am
off.
Summary:
- ACPI IRQ request deferral
- OMAP: revert deferred wakeup quirk
- MAX7301: fix DMA safe memory handling
- MVEBU: selective probe failure on missing clk"
* tag 'gpio-v4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: mvebu: only fail on missing clk if pwm is actually to be used
gpio: max7301: fix driver for use with CONFIG_VMAP_STACK
gpio: gpio-omap: Revert deferred wakeup quirk handling for regressions
gpiolib-acpi: Only defer request_irq for GpioInt ACPI event handlers
This patch adds a driver for Cadence GPIO controller.
It can be enabled with GPIO_CADENCE Kconfig option.
It uses generic GPIO infrastructure and works
as an interrupt controller.
At the moment it only supports level sensitive irqs.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Variable err is defined but never used. Remove it. Cleans up warning:
warning: unused variable ‘err’ [-Wunused-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Calling readl directly instead of going through another function that
results in the same result to remove some overhead. I didn't try to
measure the performance gain, but IMHO there is little benefit from
abstracting a GPIO register access in the GPIO driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove duplicated assignment statement from aspeed_gpio_probe() function.
Signed-off-by: Tao Ren <taoren@fb.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PIOBU pins do not lose their voltage during Backup/Self-refresh.
This patch adds a simple GPIO controller for them and a
maintainer for the driver.
This driver adds support for using the pins as GPIO
offering the possibility to read/set the voltage.
Signed-off-by: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpio IP on Armada 370 at offset 0x18180 has neither a clk nor pwm
registers. So there is no need for a clk as the pwm isn't used anyhow.
So only check for the clk in the presence of the pwm registers. This fixes
a failure to probe the gpio driver for the above mentioned gpio device.
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
spi_read() and spi_write() require DMA-safe memory. When
CONFIG_VMAP_STACK is selected, those functions cannot be used
with buffers on stack.
This patch replaces calls to spi_read() and spi_write() by
spi_write_then_read() which doesn't require DMA-safe buffers.
Fixes: 0c36ec3147 ("gpio: gpio driver for max7301 SPI GPIO expander")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit ec0daae685 ("gpio: omap: Add level wakeup handling for omap4
based SoCs") attempted to fix omap4 GPIO wakeup handling as it was
blocking deeper SoC idle states. However this caused a regression for
GPIOs during runtime having over second long latencies for Ethernet
GPIO interrupt as reportedy by Russell King <rmk+kernel@armlinux.org.uk>.
Let's fix this issue by doing a partial revert of the breaking commit.
We still want to keep the quirk handling around as it is also used for
OMAP_GPIO_QUIRK_IDLE_REMOVE_TRIGGER.
The real fix for omap4 GPIO wakeup handling involves fixes for
omap_set_gpio_trigger() and omap_gpio_unmask_irq() and will be posted
separately. And we must keep the wakeup bit enabled during runtime
because of module doing clock autogating with autoidle configured.
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Fixes: ec0daae685 ("gpio: omap: Add level wakeup handling for omap4
based SoCs")
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add level active IRQ support to regmap-irq irqchip. Change breaks
existing regmap-irq type setting. Convert the existing drivers which
use regmap-irq with trigger type setting (gpio-max77620) to work
with this new approach. So we do not magically support level-active
IRQs on gpio-max77620 - but add support to the regmap-irq for chips
which support them =)
We do not support distinguishing situation where HW supports rising
and falling edge detection but not both. Separating this would require
inventing yet another flags for IRQ types.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The device tree bindings for the MMC card detect and
write protect lines specify that these should be active
low unless "cd-inverted" or "wp-inverted" has been
specified.
However that is not how the kernel code has worked. It
has always respected the flags passed to the phandle in
the device tree, but respected the "cd-inverted" and
"wp-inverted" flags such that if those are set, the
polarity will be the inverse of that specified in the
device tree.
Switch to behaving like the old code did and fix the
regression.
Fixes: 81c85ec15a ("gpio: OF: Parse MMC-specific CD and WP properties")
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Select REGMAP_I2C in Kconfig, since the driver now depends on regmap
and this was missing, thus breaking build on various systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We're getting a reference RPi's firmware node in order to be able to
communicate with it's driver. We should decrease the reference count on
the dt node after being done with it.
Fixes: a98d90e7d5 ("gpio: raspberrypi-exp: Driver for RPi3 GPIO expander via mailbox service")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using the name directly from the I2C client
to name the gpio_chip, use dev_name() on the client->dev,
so we get the sometimes more unique device name, as I2C has
a mechanism for naming its devices explicitly in e.g.
board data.
This is a prerequisite for being able to reference
uniquely any I2C GPIO expander defined in a board file
when setting up GPIO descriptor tables.
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It is possible that the PCA953x is powered down during suspend.
Use regmap cache to assure the registers in the PCA953x are in
line with the driver state after resume.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drop pca953x_write_single() which is used in one place.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the ad-hoc reg_output output register caching with generic
regcache cache. Drop pca953x_write_single() which is no longer used.
This reduces code duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Convert the driver to use regmap to access the chips. Due to the convoluted
register mapping scheme, implement read/write/volatile check functions that
untangle the mess and perform check accordingly. This patch does not zap the
internal register cache of the PCA953x driver, nor does it push the regmap
access down into the gpiochip accessors to simplify the review. All that is
in subsequent patches.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of having the I2C register calculation function spread across
multiple accessor functions, pull it out into a single function which
returns the adjusted register address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ad-hoc i2c block write can be replaced by standard register accessor
function, which correctly handles all the chip details and differences.
Do so to simplify the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PCA957x and PCA953x init functions are almost the same, except for
the different register mapping and one extra write to BKEN register in
case of PCA957x. Factor out the common code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At this point, the pca953x_{read,write}_regs_mul() can read single bank
PCA953x GPIO chips as well. Merge the _8 and _mul functions together to
simplify the code a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At this point, these two functions only differ in whether they do or do not
set the address increment bit. The 16 GPIO case does not need to set the AI
bit, except for PCA9575 on write, while the 24 GPIO and more case does set
the AI bit always. Merge these two functions together to simplify the code
a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
At this point, these two functions only differ in whether they do or do not
set the address increment bit on PCA9575. Merge these two functions together
to simplify the code a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The multi-byte IO on various pca953x chips requires the auto-increment bit,
while other chips toggle the LSbit automatically. Note that LSbit toggling
only alternates between two registers during the IO, it is not the same as
address auto-increment. The driver currently assumes that #gpios > 16 implies
auto-increment, while #gpios <= 16 implies LSbit toggling. This is incorrect
at there are chips with 16 GPIOs which require the auto-increment bit.
The PCA9575, according to NXP datasheet rev. 4.2 from 16 April 2015, section
7.3 Command Register, the bit 7 in command register is the auto-increment
bit, which allows programming multiple registers sequentially.
Set this bit both in pca953x_gpio_set_multiple(), where it fixes the multi
register programming, and in pca957x_write_regs_16(), where is simplifies
the function. In fact, the pca957x_write_regs_16() now looks rather similar
to pca953x_write_regs_24() and pca953x_write_regs_16(), which is intended
for subsequent patches.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PCAL_PINCTRL_MASK is too large. The extended register block on
PCAL6524, which is the largest chip with this block, has the block
limited to address range 0x40..0x7f. This is because the bit 7 in
the command register is used for the Address Increment functionality.
Trim the mask to 0x60 to match the datasheet and to prevent accidental
overwrite of the AI bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bank_shift = fls(...) code was duplicated in the driver 5 times,
pull it into separate function.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IRQ core code refers to the interrupt type by that name, whereas the
term flow is almost never used. Some GPIO controllers use the term
flow_type, but it is most consistent to just go with the IRQ core
terminology.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use managed resource allocation in pch and sodaville drivers.
Switch to use for_each_set_bit() in IRQ handlers.
Headers clean up.
Sort headers in inclusion block alphabetically for better maintenance.
Convert to SPDX identifier and fixing MODULE_LICENSE() when appropriate.
Additional format fixes to rectify debug and message printing.
There is a commit which had been applied to v4.20-rc4, that's why dup.
- c3bc3ff9e8 MAINTAINERS: Do maintain Intel GPIO drivers via separate tree
The following is an automated git shortlog grouped by driver:
ich:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Join string literals back
- Convert pr_<level> to dev_<level>
- Switch to use struct device instead of platform_device
- Simplify error handling in ichx_write_bit()
intel-mid:
- Convert to use SPDX identifier
- Remove linux/module.h and sort headers
lynxpoint:
- Convert to use SPDX identifier
- Remove linux/init.h and sort headers
- Use for_each_set_bit() in IRQ handler
MAINTAINERS:
- Do maintain Intel GPIO drivers via separate tree
merrifield:
- Convert to use SPDX identifier
- Remove linux/init.h
pch:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Remove duplicate assignments
- Remove redundant __func__ from debug print
- Use for_each_set_bit() in IRQ handler
- Convert to dev_pm_ops
- Convert to use managed functions pcim_* and devm_*
sch:
- Convert to use SPDX identifier
- Remove linux/init.h and sort headers
sodaville:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Use for_each_set_bit() in IRQ handler
- Convert to use managed functions pcim_* and devm_*
-----BEGIN PGP SIGNATURE-----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=5W0M
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel
intel-gpio for v4.21-1
Use managed resource allocation in pch and sodaville drivers.
Switch to use for_each_set_bit() in IRQ handlers.
Headers clean up.
Sort headers in inclusion block alphabetically for better maintenance.
Convert to SPDX identifier and fixing MODULE_LICENSE() when appropriate.
Additional format fixes to rectify debug and message printing.
There is a commit which had been applied to v4.20-rc4, that's why dup.
- c3bc3ff9e8 MAINTAINERS: Do maintain Intel GPIO drivers via separate tree
The following is an automated git shortlog grouped by driver:
ich:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Join string literals back
- Convert pr_<level> to dev_<level>
- Switch to use struct device instead of platform_device
- Simplify error handling in ichx_write_bit()
intel-mid:
- Convert to use SPDX identifier
- Remove linux/module.h and sort headers
lynxpoint:
- Convert to use SPDX identifier
- Remove linux/init.h and sort headers
- Use for_each_set_bit() in IRQ handler
MAINTAINERS:
- Do maintain Intel GPIO drivers via separate tree
merrifield:
- Convert to use SPDX identifier
- Remove linux/init.h
pch:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Remove duplicate assignments
- Remove redundant __func__ from debug print
- Use for_each_set_bit() in IRQ handler
- Convert to dev_pm_ops
- Convert to use managed functions pcim_* and devm_*
sch:
- Convert to use SPDX identifier
- Remove linux/init.h and sort headers
sodaville:
- Convert to use SPDX identifier
- Sort headers alphabetically
- Use for_each_set_bit() in IRQ handler
- Convert to use managed functions pcim_* and devm_*
Before things go out of hand, make it possible to pass
flags when requesting "own" descriptors from a gpio_chip.
This is necessary if the chip wants to request a GPIO with
active low semantics, for example.
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a function named devm_gpiod_unhinge() that removes
the resource management from a GPIO descriptor.
I am not sure if this is the best anglosaxon name for the
function, no other managed resources have an equivalent
currently, but I chose "unhinge" as the closest intuitive
thing I could imagine that fits Rusty Russell's API design
criterions "the obvious use is the correct one" and
"the name tells you how to use it".
The idea came out of a remark from Mark Brown that it should
be possible to handle over management of a resource from
devres to the regulator core, and indeed we can do that.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When we get a nonexeclusive GPIO descriptor using managed
resources, we should only add it to the list of managed
resources once: on the first user. Augment the
devm_gpiod_get_index() and devm_gpiod_get_from_of_node()
calls to account for this by checking if the descriptor
is already resource managed before we proceed to allocate
a new resource management struct.
Fixes: b0ce7b29bf ("regulator/gpio: Allow nonexclusive GPIO access")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This makes gpiod_get_from_of_node() respect the
GPIOD_FLAGS_BIT_NONEXCLUSIVE flag which is especially
nice when getting regulator GPIOs right out of device
tree nodes.
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: b0ce7b29bf ("regulator/gpio: Allow nonexclusive GPIO access")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This function already exist inside gpiolib, we were just
reluctant to make it available to the kernel at large as
the devm_* seemed to be enough for anyone.
However we found out that regulators need to do their own
lifecycle/refcounting on GPIO descriptors and explicitly
call gpiod_put() when done with a descriptor, so export
this function so we can hand the refcounting over to the
regulator core for these descriptors after retrieveal.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The problem is reported for allmodconfig build setup:
ERROR: "irq_chip_retrigger_hierarchy" [drivers/gpio/gpio-lpc18xx.ko] undefined!
make[2]: *** [scripts/Makefile.modpost:92: __modpost] Error 1
make[1]: *** [Makefile:1271: modules] Error 2
My testing in runtime shows that it is sufficient to remove .irq_retrigger
callback, which is assigned to unexported irq_chip_retrigger_hierarchy()
function, I did't observe any regressions, and thus apparently it is a
better fix rather than exporting the function defined in kernel/irq/chip.c
(see commit 52b2a05fa7 ("genirq: Export IRQ functions for module use"))
or sticking the GPIO controller driver build to built-in option only.
Reported-by: kbuild test robot <lkp@intel.com>
Fixes: 5ddabfe8d3 ("gpio: lpc18xx: add GPIO pin interrupt controller support")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
While here, sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
While here, sort header block alphabetically for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to include linux/module.h when at the same time
we include linux/init.h.
Remove redundant inclusion.
While here, remove no-op macro and sort header block alphabetically
for easy maintenance.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
dev_dbg includes the function name & line number by default when dynamic
debugging is enabled. Hence __func__ is redundant here and removed.
Do the same for any messages in ->probe() since it doesn't make sense.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
For easy grepping on debug purposes join string literals back in the
messages.
While here, fix spelling typo.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no need to have a pointer to struct platform_device.
Instead, switch to use struct device one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Simplify error handling in ichx_write_bit() and propagate its error code
to the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This simplifies and standardizes the AB IRQ handler by using
the for_each_set_bit() library function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This simplifies and standardizes the AB IRQ handler by using
the for_each_set_bit() library function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
checkpatch.pl suggests to use SPDX license tag. I am happy to
follow it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Zynq's gpios can be configured by the bootloader. But Linux will
erroneously report all gpios as inputs unless we implement
get_direction().
Signed-off-by: Brandon Maier <Brandon.Maier@collins.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 78d3a92edb ("gpiolib-acpi: Register GpioInt ACPI event handlers
from a late_initcall") deferred the entire acpi_gpiochip_request_interrupt
call for each event resource.
This means it also delays the gpiochip_request_own_desc(..., "ACPI:Event")
call. This is a problem if some AML code reads the GPIO pin before we
run the deferred acpi_gpiochip_request_interrupt, because in that case
acpi_gpio_adr_space_handler() will already have called
gpiochip_request_own_desc(..., "ACPI:OpRegion") causing the call from
acpi_gpiochip_request_interrupt to fail with -EBUSY and we will fail to
register an event handler.
acpi_gpio_adr_space_handler is prepared for acpi_gpiochip_request_interrupt
already having claimed the pin, but the other way around does not work.
One example of a problem this causes, is the event handler for the OTG
ID pin on a Prowise PT301 tablet not registering, keeping the port stuck
in whatever mode it was in during boot and e.g. only allowing charging
after a reboot.
This commit fixes this by only deferring the request_irq call and the
initial run of edge-triggered IRQs instead of deferring all of
acpi_gpiochip_request_interrupt.
Cc: stable@vger.kernel.org
Fixes: 78d3a92edb ("gpiolib-acpi: Register GpioInt ACPI event ...")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change adds support of LPC18xx/LPC43xx GPIO pin interrupt controller
block within SoC GPIO controller. The new interrupt controller driver
allows to configure and capture edge or level interrupts on 8 arbitrary
selectedinput GPIO pins, and lift the signals to be reported as NVIC rising
edge interrupts. Configuration of a particular GPIO pin to serve as
interrupt and its mapping to an interrupt on NVIC is done by SCU pin
controller, for more details see description of 'nxp,gpio-pin-interrupt'
device tree property of a GPIO pin [1].
From LPC18xx and LPC43xx User Manuals the GPIO controller consists of
the following blocks:
* GPIO pin interrupt block at 0x40087000, this change adds its support,
* GPIO GROUP0 interrupt block at 0x40088000,
* GPIO GROUP1 interrupt block at 0x40089000,
* GPIO port block at 0x400F4000, it is supported by the original driver.
While all 4 sub-controller blocks have their own I/O addresses, moreover
all 3 interrupt blocks are APB0 peripherals and high-speed GPIO block is
an AHB slave, according to the hardware manual the GPIO controller is
seen as a single block, and 4 sub-controllers have the shared reset signal
RGU #28 and clock to register interface CLK_CPU_GPIO on CCU1.
Likely support of two GPIO group interrupt blocks won't be added in short
term, because the mechanism to mask several interrupt sources is not well
defined.
[1] Documentation/devicetree/bindings/pinctrl/nxp,lpc1850-scu.txt
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a non-functional change, it simplifies multiple access to
'struct device' pointer derived from a platform device pointer,
the new local variable will also be used in the following changes.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace GPLv2 header with the SPDX identifier.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The error cases of mediatek_gpio_bank_probe() would go unnoticed (except
for the dev_err() messages). The probe function should return an error
if one of the banks failed to initialize properly indicated by
not returning non-0.
Fixes: 4ba9c3afda ("gpio: mt7621: Add a driver for MT7621")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
kasprintf() may return NULL on failure of internal allocation thus the
assigned label is not safe if not explicitly checked. On error
mediatek_gpio_bank_probe() returns negative values so -ENOMEM in the
(unlikely) failure case should be fine here.
Fixes: 4ba9c3afda ("gpio: mt7621: Add a driver for MT7621")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change simplifies dereferences to the mediated struct device, also
it allows to limit the scope of the platform device usage to probe and
remove functions only.
Non-functional change.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This simplifies and standardizes the AB IRQ handler by using
the for_each_set_bit() library function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Convert the legacy system PM callbacks to new ones. Meanwhile, remove the
redundant calls to the PCI for changing a power state since it's done by bus
code.
While here, remove weird indentation with backslash in use.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Volume is a little higher than usual due to a set of gpio fixes for
Davinci platforms that's been around a while, still seemed appropriate
to not hold off until next merge window.
Besides that it's the usual mix of minor fixes, mostly corrections of
small stuff in device trees.
Major stability-related one is the removal of a regulator from DT on
Rock960, since DVFS caused undervoltage. I expect it'll be restored once
they figure out the underlying issue.
-----BEGIN PGP SIGNATURE-----
iQJDBAABCAAtFiEElf+HevZ4QCAJmMQ+jBrnPN6EHHcFAlwEMLEPHG9sb2ZAbGl4
b20ubmV0AAoJEIwa5zzehBx3WewP/2shRXHQ8mSwMbqLApBUgPASpGtyJsLgP4vX
ROMHdfQr2nhZPu9vy973aVAztkG3FCsWNhKqNVWTfvNf9eNYRh62D8/gqNYavQJH
Gtq/TpiJWWDWoXzxHpOE5vSunNDUGWRrbigmgcONogNs42iX0ngLAy7GWzWHB7oc
O3HAYxNevsBTJkkKpKGnDqDM1P4WaEG5OPdjMUN25UD7IBshzuVq4eG3LuqLLZ01
NzGV/RErCnnLP8VSJlu+LQkLBeO5WpcvqZMeC6lNGBEBQAscTYRTucmM9tflJgCK
B3+GczLFdJXKwluVV055MfrBxUweZ+Tm2gk7Ojtou/ozhFOdWICVT6KSwTHiOUIB
ZDP/f56QfJCxxc/NFX5fJHSaYhXl+tj1HVxwG/dK/l3blMOX5I7cZkBKnjI9sDVl
H3on9r5S3j1x1T534zf/n0OUwztIBmPiEZTPeoz6L1HuqpusmWJZB3knW6RnA4Lv
3JQPowK2k97/3Xp4xnzl5rQreBomXv1hsszXmPKX0pIFXF1C+BQ0LwNd9cC/Hnq2
dz02JkzoAoEg1L5DYhG63vg/3beg//3Z7uGNMu4LMcaNlLxl5AqMM7O18qJCfMth
nFZRx+ZkZ7h8EJqXnMxnXgwHUzWN6Iq2AjKFfmVWRQcDZk+Ys9BlRV5O9m0N0JHb
KfdtL0SC
=m41T
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Volume is a little higher than usual due to a set of gpio fixes for
Davinci platforms that's been around a while, still seemed appropriate
to not hold off until next merge window.
Besides that it's the usual mix of minor fixes, mostly corrections of
small stuff in device trees.
Major stability-related one is the removal of a regulator from DT on
Rock960, since DVFS caused undervoltage. I expect it'll be restored
once they figure out the underlying issue"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
MAINTAINERS: Remove unused Qualcomm SoC mailing list
ARM: davinci: dm644x: set the GPIO base to 0
ARM: davinci: da830: set the GPIO base to 0
ARM: davinci: dm355: set the GPIO base to 0
ARM: davinci: dm646x: set the GPIO base to 0
ARM: davinci: dm365: set the GPIO base to 0
ARM: davinci: da850: set the GPIO base to 0
gpio: davinci: restore a way to manually specify the GPIO base
ARM: davinci: dm644x: define gpio interrupts as separate resources
ARM: davinci: dm355: define gpio interrupts as separate resources
ARM: davinci: dm646x: define gpio interrupts as separate resources
ARM: davinci: dm365: define gpio interrupts as separate resources
ARM: davinci: da8xx: define gpio interrupts as separate resources
ARM: dts: at91: sama5d2: use the divided clock for SMC
ARM: dts: imx51-zii-rdu1: Remove EEPROM node
ARM: dts: rockchip: Remove @0 from the veyron memory node
arm64: dts: rockchip: Fix PCIe reset polarity for rk3399-puma-haikou.
arm64: dts: qcom: msm8998: Reserve gpio ranges on MTP
arm64: dts: sdm845-mtp: Reserve reserved gpios
arm64: dts: ti: k3-am654: Fix wakeup_uart reg address
...
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This makes the error handling much more simpler than open-coding everything
and in addition makes the probe function smaller an tidier.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
When retrieveing CD (card detect) and WP (write protect)
GPIO handles from the device tree, make sure to assign
them active low by default unless the "cd-inverted" or
"wp-inverted" properties are set. These properties mean
that respective signal is active HIGH since the SDHCI
specification stipulates that this kind of signals
should be treated as active LOW.
If the twocell GPIO flag is also specified as active
low, well that's nice and we will silently ignore the
tautological specification.
If however the GPIO line is specified as active low
in the GPIO flasg cell and "cd-inverted" or "wp-inverted"
is also specified, the latter takes precedence and we
print a warning.
The current effect on the MMC slot-gpio core are as
follows:
For CD GPIOs: no effect. The current code in
mmc/core/host.c calls mmc_gpiod_request_cd() with
the "override_active_level" argument set to true,
which means that whatever the GPIO descriptor
thinks about active low/high will be ignored, the
core will use the MMC_CAP2_CD_ACTIVE_HIGH to keep
track of this and reads the raw value from the
GPIO descriptor, totally bypassing gpiolibs inversion
semantics. I plan to clean this up at a later point
passing the handling of inversion semantics over
to gpiolib, so this patch prepares the ground for
that.
Fow WP GPIOs: this is probably fixing a bug, because
the code in mmc/core/host.c calls mmc_gpiod_request_ro()
with the "override_active_level" argument set to false,
which means it will respect the inversion semantics of
the gpiolib and ignore the MMC_CAP2_RO_ACTIVE_HIGH
flag for everyone using this through device tree.
However the code in host.c confusingly goes to great
lengths setting up the MMC_CAP2_RO_ACTIVE_HIGH flag
from the GPIO descriptor and by reading the "wp-inverted"
property of the node. As far as I can tell this is all
in vain and the inversion is broken: device trees that
use "wp-inverted" do not work as intended, instead the
only way to actually get inversion on a line is by
setting the second cell flag to GPIO_ACTIVE_HIGH (which
will be the default) or GPIO_ACTIVE_LOW if they want
the proper MMC semantics. Presumably all device trees do
this right but we need to parse and handle this properly.
Cc: linux-mmc@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 587f7a694f ("gpio: davinci: Use dev name for label and
automatic base selection") broke the network support in legacy boot
mode for da850-evm since we can no longer request the MDIO clock GPIO.
Other boards may be broken too, which I haven't tested.
The problem is in the fact that most board files still use the legacy
GPIO API where lines are requested by numbers rather than descriptors.
While this should be fixed eventually, in order to unbreak the board
for now - provide a way to manually specify the GPIO base in platform
data.
Fixes: 587f7a694f ("gpio: davinci: Use dev name for label and automatic base selection")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
It's easy to verify that the change of drivers/gpio/gpiolib-of.c license
header to SPDX standard changes the license from GPLv2+ to GPLv2, and
this change corrects it.
Fixes: dae5f0afcf ("gpio: Use SPDX header for core library")
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove linux/gpio/driver.h which is included more than once
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some SoCs need the gpio clock to be enabled before accessing
HW registers. This patch add the optional clock handling.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 3edfb7bd76 ("gpiolib: Show correct direction from the
beginning") fixed an existing issue but broke libgpiod tests by
changing the default direction of dummy lines to output.
We don't break user-space so make gpio-mockup behave as before.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As pointed out by Gregor, spitz keyboard matrix is broken, with or
without CONFIG_PINCTRL set, quoting :
"The gpio matrix keypard on the Zaurus C3x00 (see spitz.c) does not work
properly. Noticeable are that rshift+c does nothing where as lshift+c
creates C. Opposite it is for rshift+a vs lshift+a, here only rshift
works. This affects a few other combinations using the rshift or lshift
buttons."
As a matter of fact, as for platform_data based builds CONFIG_PINCTRL=n
is required for now (as opposed for devicetree builds where it should be
set), this means gpio driver should change the direction, which is what
was attempted by commit c4e5ffb6f2 ("gpio: pxa: fix legacy non pinctrl
aware builds").
Unfortunately, the input case was inverted, and the direction change was
never done. This wasn't seen up until now because the initial platform
setup (MFP) was setting this direction. Yet in Gregory's case, the
matrix-keypad driver changes back and forth the direction dynamically,
and this is why he's the first to report it.
Fixes: c4e5ffb6f2 ("gpio: pxa: fix legacy non pinctrl aware builds")
Tested-by: Greg <greguu@null.net>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
During noirq suspend/resume phase, GPIO irq could arrive
and its registers like IMR will be changed by irq handle
process, to make the GPIO registers exactly when it is
powered ON after resume, move the GPIO noirq suspend/resume
callback to syscore suspend/resume phase, local irq is
disabled at this phase so GPIO registers are atomic.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch updates license to use SPDX-License-Identifier
instead of verbose license text.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 48207d7595 ("gpio: drop devm_gpiochip_remove()") dropped the
last user of drop devm_gpio_chip_match(), causing a defined but not used
compilation warning. Fix it by removing the function.
Fixes: 48207d7595 ("gpio: drop devm_gpiochip_remove()")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The change corrects the error path in gpiochip_add_data_with_key()
by avoiding to call ida_simple_remove(), if ida_simple_get() returns
an error.
Note that ida_simple_remove()/ida_free() throws a BUG(), if id argument
is negative, it allows to easily check the correctness of the fix by
fuzzing the return value from ida_simple_get().
Fixes: ff2b135922 ("gpio: make the gpiochip a real device")
Cc: stable@vger.kernel.org # v4.6+
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiod_request_commit() copies the pointer to the label passed as
an argument only to be used later. But there's a chance the caller
could immediately free the passed string(e.g., local variable).
This could trigger a use after free when we use gpio label(e.g.,
gpiochip_unlock_as_irq(), gpiochip_is_requested()).
To be on the safe side: duplicate the string with kstrdup_const()
so that if an unaware user passes an address to a stack-allocated
buffer, we won't get the arbitrary label.
Also fix gpiod_set_consumer_name().
Signed-off-by: Muchun Song <smuchun@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Trivial fix to clean up an indentation issue, remove space
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Keeping the irq_chip definition static will make it shared with multiple
giochips in the system. This practice is considered to be bad and now we
will get the below warning from gpiolib core:
"detected irqchip that is shared with multiple gpiochips: please fix the
driver."
Hence, move the irq_chip definition from static to `struct pl061` for
using a unique irq_chip for each gpiochip.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is hardly any reason to call devm_gpiochip_remove() because the
driver core handles calling gpiochip_remove() automatically.
To make it harder to introduce new (and probably unneeded) callers, drop
the function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch masks the read inputs with the word mask in order to ensure
only requested input states are returned in the bits array.
Suggested-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With a new subsystem co-maintainer on board it is good to draw
up the ongoing changes and future plans for the subsystem, i.e.
what is in my head and being worked on long term.
What better way is there than simply adding a TODO right in the
code and send it out to the mailing list.
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO
lines as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can
use only the fastpatch callbacks to enable/disable irqs
like any normal irqchip, especially the gpiod_lock_as_irq()
has been improved to be callable in fastpath context.
A bunch of rework had to be done to achieve this but it is
a big win since I never liked to restrict this to slowpath.
The only call requireing slowpath was try_module_get() and
this is kept at the .request_resources() slowpath callback.
In the GPIO CEC driver this is a big win sine a single
line is used for both outgoing and incoming traffic, and
this needs to use IRQs for incoming traffic while actively
driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a
"cookie" (struct gpio_array) and a bitmap for setting or
getting multiple GPIO lines at once. This improvement
orginated in a specific need to speed up an OMAP1 driver and
has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot
of checks and code when we want things to go really fast.
The previous code would minimize the number of calls
down to the driver callbacks assuming the CPU speed was
orders of magnitude faster than the I/O latency, but this
assumption was wrong on several platforms: what we needed
to do was to profile and improve the speed on the hot
path of the array functions and this change is now
completed.
- Clean out the painful and hard to grasp BNF experiments
from the device tree bindings. Future approaches are looking
into using JSON schema for this purpose. (Rob Herring
is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and
other contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin
control driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver.
-----BEGIN PGP SIGNATURE-----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=YosT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.20 series:
Core changes:
- A patch series from Hans Verkuil to make it possible to
enable/disable IRQs on a GPIO line at runtime and drive GPIO lines
as output without having to put/get them from scratch.
The irqchip callbacks have been improved so that they can use only
the fastpatch callbacks to enable/disable irqs like any normal
irqchip, especially the gpiod_lock_as_irq() has been improved to be
callable in fastpath context.
A bunch of rework had to be done to achieve this but it is a big
win since I never liked to restrict this to slowpath. The only call
requireing slowpath was try_module_get() and this is kept at the
.request_resources() slowpath callback. In the GPIO CEC driver this
is a big win sine a single line is used for both outgoing and
incoming traffic, and this needs to use IRQs for incoming traffic
while actively driving the line for outgoing traffic.
- Janusz Krzysztofik improved the GPIO array API to pass a "cookie"
(struct gpio_array) and a bitmap for setting or getting multiple
GPIO lines at once.
This improvement orginated in a specific need to speed up an OMAP1
driver and has led to a much better API and real performance gains
when the state of the array can be used to bypass a lot of checks
and code when we want things to go really fast.
The previous code would minimize the number of calls down to the
driver callbacks assuming the CPU speed was orders of magnitude
faster than the I/O latency, but this assumption was wrong on
several platforms: what we needed to do was to profile and improve
the speed on the hot path of the array functions and this change is
now completed.
- Clean out the painful and hard to grasp BNF experiments from the
device tree bindings. Future approaches are looking into using JSON
schema for this purpose. (Rob Herring is floating a patch series.)
New drivers:
- The RCAR driver now supports r8a774a1 (RZ/G2M).
- Synopsys GPIO via CREGs driver.
Major improvements:
- Modernization of the EP93xx driver to use irqdomain and other
contemporary concepts.
- The ingenic driver has been merged into the Ingenic pin control
driver and removed from the GPIO subsystem.
- Debounce support in the ftgpio010 driver"
* tag 'gpio-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (116 commits)
gpio: Clarify kerneldoc on gpiochip_set_chained_irqchip()
gpio: Remove unused 'irqchip' argument to gpiochip_set_cascaded_irqchip()
gpio: Drop parent irq assignment during cascade setup
mmc: pwrseq_simple: Fix incorrect handling of GPIO bitmap
gpio: fix SNPS_CREG kconfig dependency warning
gpiolib: Initialize gdev field before is used
gpio: fix kernel-doc after devres.c file rename
gpio: fix doc string for devm_gpiochip_add_data() to not talk about irq_chip
gpio: syscon: Fix possible NULL ptr usage
gpiolib: Show correct direction from the beginning
pinctrl: msm: Use init_valid_mask exported function
gpiolib: Add init_valid_mask exported function
GPIO: add single-register GPIO via CREG driver
dt-bindings: Document the Synopsys GPIO via CREG bindings
gpio: mockup: use device properties instead of platform_data
gpio: Slightly more helpful debugfs
gpio: omap: Remove set but not used variable 'dev'
gpio: omap: drop omap_gpio_list
Accept partial 'gpio-line-names' property.
gpio: omap: get rid of the conditional PM runtime calls
...
There were no significant changes to the core this time!
New drivers:
- Broadcom Northstar pin control driver.
- Mediatek MT8183 subdriver.
- Mediatek MT7623 subdriver.
- Mediatek MT6765 subdriver.
- Meson g12a subdriver.
- Nuvoton NPCM7xx pin control and GPIO driver.
- Qualcomm QCS404 pin control and GPIO subdriver.
- Qualcomm SDM660 pin control and GPIO subdriver.
- Renesas R8A7744 PFC subdriver.
- Renesas R8A774C0 PFC subdriver.
- Renesas RZ/N1 pinctrl driver
Major improvements:
- Pulled the GPIO support for Ingenic over from the GPIO
subsystem and consolidated it all in the Ingenic pin control
driver.
- Major cleanups and consolidation work in all Intel drivers.
- Major cleanups and consolidation work in all Mediatek drivers.
- Lots of incremental improvements to the Renesas PFC pin
controller family.
- All drivers doing GPIO now include <linux/gpio/driver.h> and
nothing else.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJbzcMKAAoJEEEQszewGV1z7UYP/1XnwE8EyOam4XuQMQPI5t3w
q6vUDClR2dgLDFdQOaSU+5+GgO9ke/RLLIcp9e4EWS7a9gcq7Q/w371GL3PplnKZ
s718SJnJRUGO4Cdzz57emhsqXgJus6Clj11Gqtey+s6a5rlaJJldgRrwha2iGCaP
Wn3OByCtRNlvRPDmP7EmO+BeZrYvN9xzC7trweetKxx6/QibopnrgRPmARn5HvEq
0myUQis8RSpZ3ck1Ky375WKnUkeuVoADp7PeH12gQUYdvhQ5+G9/4NDAkUuShYD/
RLylNCVwgKOU4zhH/z2Rx0zY92u6JjDphiM6GSt1z0DUf3hmp2sJkQWUrLJJmh2t
MO5csePHn18UXiHSee8Uhc39dHDY5wCywScYetFZuJwhhJY9yGQ0610qpO2HQ67q
9RobHS6pH8EWqIqwFe9rg4YncWU9R7gkxHAMSEBvnrXKyHNTl35lKHwyKQzgUKDu
EXbgoE7cKMTGtlD9paMltDNM9rDQfARnKxI8gW43ju0AKfIdBrWlVYwGiGxmfvpm
Fzb7I6stEKs8EprgHo7/SYUZPhFpQVzX+VMWQxbag2aQoMx1jHGYT4yDf7Z1Liy0
2/8SZDqOnyWOCt/Npb/v7yS8+9FQ3PL3OndsgfoZIKyyBTO+lnMzXVFkn0g9umXc
5rASYfGie9JTXW7XeQ17
=rBtH
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.20 series:
There were no significant changes to the core this time! Bur the new
Qualcomm, Mediatek and Broadcom drivers are quite interesting as they
will be used in a few million embedded devices the coming years as it
seems.
New drivers:
- Broadcom Northstar pin control driver.
- Mediatek MT8183 subdriver.
- Mediatek MT7623 subdriver.
- Mediatek MT6765 subdriver.
- Meson g12a subdriver.
- Nuvoton NPCM7xx pin control and GPIO driver.
- Qualcomm QCS404 pin control and GPIO subdriver.
- Qualcomm SDM660 pin control and GPIO subdriver.
- Renesas R8A7744 PFC subdriver.
- Renesas R8A774C0 PFC subdriver.
- Renesas RZ/N1 pinctrl driver
Major improvements:
- Pulled the GPIO support for Ingenic over from the GPIO subsystem
and consolidated it all in the Ingenic pin control driver.
- Major cleanups and consolidation work in all Intel drivers.
- Major cleanups and consolidation work in all Mediatek drivers.
- Lots of incremental improvements to the Renesas PFC pin controller
family.
- All drivers doing GPIO now include <linux/gpio/driver.h> and
nothing else"
* tag 'pinctrl-v4.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (153 commits)
pinctrl: sunxi: Fix a memory leak in 'sunxi_pinctrl_build_state()'
gpio: uniphier: include <linux/bits.h> instead of <linux/bitops.h>
pinctrl: uniphier: include <linux/bits.h> instead of <linux/bitops.h>
dt-bindings: pinctrl: bcm4708-pinmux: improve example binding
pinctrl: geminilake: Sort register offsets by value
pinctrl: geminilake: Get rid of unneeded ->probe() stub
pinctrl: geminilake: Update pin list for B0 stepping
pinctrl: renesas: Fix platform_no_drv_owner.cocci warnings
pinctrl: mediatek: Make eint_m u16
pinctrl: bcm: ns: Use uintptr_t for casting data
pinctrl: madera: Fix uninitialized variable bug in madera_mux_set_mux
pinctrl: gemini: Fix up TVC clock group
pinctrl: gemini: Drop noisy debug prints
pinctrl: gemini: Mask and set properly
pinctrl: mediatek: select GPIOLIB
pinctrl: rza1: don't manually release devm managed resources
MAINTAINERS: update entry for Mediatek pin controller
pinctrl: bcm: add Northstar driver
dt-bindings: pinctrl: document Broadcom Northstar pin mux controller
pinctrl: qcom: fix 'const' pointer handling
...
The reason of including <linux/bitops.h> here is just for BIT() and
GENMASK macros.
Since commit 8bd9cb51da ("locking/atomics, asm-generic: Move some
macros from <linux/bitops.h> to a new <linux/bits.h> file"),
<linux/bits.h> is enough for such compile-time macros.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This doesn't support nested anymore, so drivers shouldn't call it with
the handler set to NULL.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This argument hasn't ever been used since it was introduced in commit
1425052097 ("gpio: add IRQ chip helpers in gpiolib"). Let's drop it to
reduce reading confusion.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We want to set the irq parent for interrupts that we're setting up to be
cascaded from another interrupt controller, but we may or may not have
already mapped the gpiochip irqs into the kernel's virtual irq number
space at this point. If we have mapped irqs before calling here, then
we've gone through gpiochip_irq_map() and called irq_set_parent()
already. If we haven't mapped irqs, then the gpiochip is dynamically
mapping irqs and we can rely on gpiochip_irq_map() or the gpio driver's
irqdomain ops to setup the irq parent properly.
Either way, setting the parent here when cascading the gpiochip doesn't
make much sense because it should be done at irq mapping time. In the
dynamic mapping case, this code is mapping virq 0 to some parent virq in
a loop. While that's benign, let's drop this code to simplify.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix kconfig warning for GPIO_SNPS_CREG:
WARNING: unmet direct dependencies detected for OF_GPIO
Depends on [n]: GPIOLIB [=y] && OF [=n] && HAS_IOMEM [=y]
Selected by [y]:
- GPIO_SNPS_CREG [=y] && GPIOLIB [=y] && HAS_IOMEM [=y] && (ARC || COMPILE_TEST [=y])
Drivers in drivers/gpio/Kconfig depend on OF_GPIO, not select it.
This prevents attempting to build when OF is not enabled.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows nonexclusive (simultaneous) access to a single
GPIO line for the fixed regulator enable line. This happens
when several regulators use the same GPIO for enabling and
disabling a regulator, and all need a handle on their GPIO
descriptor.
This solution with a special flag is not entirely elegant
and should ideally be replaced by something more careful as
this makes it possible for several consumers to
enable/disable the same GPIO line to the left and right
without any consistency. The current use inside the regulator
core should however be fine as it takes special care to
handle this.
For the state of the GPIO backend, this is still the
lesser evil compared to going back to global GPIO
numbers.
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Jon Hunter <jonathanh@nvidia.com>
Fixes: efdfeb079c ("regulator: fixed: Convert to use GPIO descriptor only")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
gpio_hog depends on gdev field being initialized. This patch fixes an
OOPs during initialization of TI's AM335x-ICEv2.
Fixes: 3edfb7bd76 ("gpiolib: Show correct direction from the beginning")
Tested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpiochip_set_cascaded_irqchip() is passed 'parent_irq' as an argument
and then the address of that argument is assigned to the gpio chips
gpio_irq_chip 'parents' pointer shortly thereafter. This can't ever
work, because we've just assigned some stack address to a pointer that
we plan to dereference later in gpiochip_irq_map(). I ran into this
issue with the KASAN report below when gpiochip_irq_map() tried to setup
the parent irq with a total junk pointer for the 'parents' array.
BUG: KASAN: stack-out-of-bounds in gpiochip_irq_map+0x228/0x248
Read of size 4 at addr ffffffc0dde472e0 by task swapper/0/1
CPU: 7 PID: 1 Comm: swapper/0 Not tainted 4.14.72 #34
Call trace:
[<ffffff9008093638>] dump_backtrace+0x0/0x718
[<ffffff9008093da4>] show_stack+0x20/0x2c
[<ffffff90096b9224>] __dump_stack+0x20/0x28
[<ffffff90096b91c8>] dump_stack+0x80/0xbc
[<ffffff900845a350>] print_address_description+0x70/0x238
[<ffffff900845a8e4>] kasan_report+0x1cc/0x260
[<ffffff900845aa14>] __asan_report_load4_noabort+0x2c/0x38
[<ffffff900897e098>] gpiochip_irq_map+0x228/0x248
[<ffffff900820cc08>] irq_domain_associate+0x114/0x2ec
[<ffffff900820d13c>] irq_create_mapping+0x120/0x234
[<ffffff900820da78>] irq_create_fwspec_mapping+0x4c8/0x88c
[<ffffff900820e2d8>] irq_create_of_mapping+0x180/0x210
[<ffffff900917114c>] of_irq_get+0x138/0x198
[<ffffff9008dc70ac>] spi_drv_probe+0x94/0x178
[<ffffff9008ca5168>] driver_probe_device+0x51c/0x824
[<ffffff9008ca6538>] __device_attach_driver+0x148/0x20c
[<ffffff9008ca14cc>] bus_for_each_drv+0x120/0x188
[<ffffff9008ca570c>] __device_attach+0x19c/0x2dc
[<ffffff9008ca586c>] device_initial_probe+0x20/0x2c
[<ffffff9008ca18bc>] bus_probe_device+0x80/0x154
[<ffffff9008c9b9b4>] device_add+0x9b8/0xbdc
[<ffffff9008dc7640>] spi_add_device+0x1b8/0x380
[<ffffff9008dcbaf0>] spi_register_controller+0x111c/0x1378
[<ffffff9008dd6b10>] spi_geni_probe+0x4dc/0x6f8
[<ffffff9008cab058>] platform_drv_probe+0xdc/0x130
[<ffffff9008ca5168>] driver_probe_device+0x51c/0x824
[<ffffff9008ca59cc>] __driver_attach+0x100/0x194
[<ffffff9008ca0ea8>] bus_for_each_dev+0x104/0x16c
[<ffffff9008ca58c0>] driver_attach+0x48/0x54
[<ffffff9008ca1edc>] bus_add_driver+0x274/0x498
[<ffffff9008ca8448>] driver_register+0x1ac/0x230
[<ffffff9008caaf6c>] __platform_driver_register+0xcc/0xdc
[<ffffff9009c4b33c>] spi_geni_driver_init+0x1c/0x24
[<ffffff9008084cb8>] do_one_initcall+0x240/0x3dc
[<ffffff9009c017d0>] kernel_init_freeable+0x378/0x468
[<ffffff90096e8240>] kernel_init+0x14/0x110
[<ffffff9008086fcc>] ret_from_fork+0x10/0x18
The buggy address belongs to the page:
page:ffffffbf037791c0 count:0 mapcount:0 mapping: (null) index:0x0
flags: 0x4000000000000000()
raw: 4000000000000000 0000000000000000 0000000000000000 00000000ffffffff
raw: ffffffbf037791e0 ffffffbf037791e0 0000000000000000 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffffffc0dde47180: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0dde47200: f1 f1 f1 f1 f8 f8 f8 f8 f8 f8 f8 f8 f8 f8 f2 f2
>ffffffc0dde47280: f2 f2 00 00 00 00 00 00 00 00 00 00 f3 f3 f3 f3
^
ffffffc0dde47300: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffffffc0dde47380: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Let's leave around one unsigned int in the gpio_irq_chip struct for the
single parent irq case and repoint the 'parents' array at it. This way
code is left mostly intact to setup parents and we waste an extra few
bytes per structure of which there should be only a handful in a system.
Cc: Evan Green <evgreen@chromium.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Fixes: e0d8972898 ("gpio: Implement tighter IRQ chip integration")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
