Make it obvious that unexpected value read from ID register is printed in
hexadecimal.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Developing a driver for an Asus X205TA laptop I get these dmesg
errors:
rt5645 i2c-10EC5648:00: ASoC: mux RT5650 IF1 ADC1 Swap Mux has no paths
rt5645 i2c-10EC5648:00: ASoC: mux RT5650 IF1 ADC2 Swap Mux has no paths
rt5645 i2c-10EC5648:00: ASoC: mux RT5650 IF1 ADC3 Swap Mux has no paths
rt5645 i2c-10EC5648:00: ASoC: mux RT5650 IF1 ADC Mux has no paths
rt5645 i2c-10EC5648:00: ASoC: mux RT5650 IF1 DAC1 L Mux has no paths
rt5645 i2c-10EC5648:00: ASoC: mux RT5650 IF1 DAC1 R Mux has no paths
rt5645 i2c-10EC5648:00: ASoC: mux RT5650 IF1 DAC2 L Mux has no paths
rt5645 i2c-10EC5648:00: ASoC: mux RT5650 IF1 DAC2 R Mux has no paths
so, move these muxes to the rt5650_specific_dapm_widgets[] list.
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since hp-detect is optional, use devm_gpiod_get_optional instead.
In additional, it should return error if devm_gpiod_get_optional fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify the RT5645 driver to parse platform data from device tree. This is
missing from previous patch in sound/soc/codecs/rt5645.c, that was present
in v3.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move gpio to gpio_desc and use gpiod APIs in codec driver.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVddV1AAoJECTWi3JdVIfQQQsH/RG3lgOeot5jLWMsxJSKChEl
KI+aaMcOw6Dj2LDccN8i6vUp8q44cKSXIc7lGLOzJW4K+OydCCGAvE+sJGyRE1dd
yOHwcbvjJi4zFlt01RZchJ/Wa/S6zFucl5N9HxWsV4bEtfAA59IuhJLtospUlwsA
mf9mpvSdeUAeh3lM2+AqAbXhTo6dYfD5ky5nrtpAkZjG8gqUG0u8Tpauja0lLcHi
72/3EkzKR6KHaefyPw3LdN+/H/YK79uHCVcctZnQg5xUUymcO16ReoTxKwV9cnDb
lBJ6wO8RpUAO9evoG2Yj/l4p+czDCm5VkHMq0nPklHVRh7s/2PwKfox1aw4Pumg=
=wolq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2' into asoc-rt5645
ASoC: Updates for v4.2
The big thing this release has been Liam's addition of topology support
to the core. We've also seen quite a bit of driver work and the
continuation of Lars' refactoring for component support.
- Support for loading ASoC topology maps from firmware, intended to be
used to allow self-describing DSP firmware images to be built which
can map controls added by the DSP to userspace without the kernel
needing to know about individual DSP firmwares.
- Lots of refactoring to avoid direct access to snd_soc_codec where
it's not needed supporting future refactoring.
- Big refactoring and cleanup serieses for the Wolfson ADSP and TI
TAS2552 drivers.
- Support for TI TAS571x power amplifiers.
- Support for Qualcomm APQ8016 and ZTE ZX296702 SoCs.
- Support for x86 systems with RT5650 and Qualcomm Storm.
Register RT5650_TDM_CTRL_4(0x7A) is readable and used for mixer
setting. It should be added in rt5645_readable_register function.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5645_enable_push_button_irq uses snd_soc_dapm_*_unlocked
functions, so it needs to lock the required dapm mutex.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prevents frequent panic on boot, if the irq handler rt5645_irq
gets called before the workqueue rt5645_jack_detect_work is
initialized.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Use the standard name "Headphone" instead of "HP" for better
userspace integration.
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Acked-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5645_set_jack_detect() is usually called from
snd_soc_dai_link.init() and it calls snd_soc_jack_report() from
rt5645_irq_detection() if jack is inserted. snd_soc_jack_report()
results in kernel hang if it is called from a context which cannot
sleep.
This patch makes sure snd_soc_jack_report() is called from
workqueue. It can fix the kernel hang issue.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5645_jack_detect doesn't report the correct jack type consistently.
It mistakes OMTP type headset to CTIA type in particular HW design.
Register changes are needed for this issue. This patch can make it
more stable.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
IRQ of jack and button detection is abnormal if "LDO2" and
"Mic Det Power" power disable in rt5645_jack_detect.
This patch make these two power keep enabled until jack out.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The power of "micbias1" and "micbias2" are unnecessary for jack detection.
So, we remove it in rt5645_set_jack_detect function.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We add a calibration function and call it at the beginning of i2c_probe.
The calibration value will be kept until codec is shutdown. We will reset
the codec after the calibration is finished. So, we set cache_bypass in
the calibration function. The benefit is we can shorter the delay time
in headphone depop.
We also change the register setting in the depop sequence which will
reduce the pop noise in headphone playback.
Signed-off-by: John Lin <john.lin@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code uses wrong mask when setting RT5645_DMIC_2_DP_GPIO12 bit,
fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the ACPI match ID for rt5645/5650 codec
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We can know if dmic is used by reading the value of dmic1_data_pin
and dmic2_data_pin. Also IRQ must be used if codec JD or button
detection function is used. So, dmic_en and en_jd_func can be remove
from platform data.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"IF1 DAC0" and "IF1 DAC3" are used in rt5645_dapm_routes but missing
in rt5645_dapm_widgets.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The volume blocks have an step of 0.375dB, but TLV uses 0.01dB for
units. Only use the resolution supported, ignoring the LSB of the
volume register. This results in half the steps and 0.75dB per step,
but reports accurate levels through TLV.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds TDM slot control into dapm route. The control bits
are different between rt5645 and rt5650, so we have separate dapm
routes for each codec.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5645_I2S_BCLK_MS1 (reg 0x73 [5]) is reserverd in rt5645 and rt5650.
This function is move to TDM control. We can configure it by
snd_soc_dai_set_tdm_slot's slot_width parameter.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5645->btn_jack is for jack button report. So the mask should be
SND_JACK_BTN_0 | SND_JACK_BTN_1 | SND_JACK_BTN_2 | SND_JACK_BTN_3.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
kbuild robot reports a implicit declaration of function
'rt5645_irq_detection' error.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5650 support headset button detection. Currently, the button detection
is only implemented for rt5650 codec. The button detection configuration
register's default value is different from rt5645.
And we didn't touch the register in the driver, so we will get the wrong
value when we dump the registers. We will fix it in another patch.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
while building as a module we are getting warning about
section mismatch.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
kbuild robot reports following error/warnings
sound/soc/codecs/rt5645.c: In function 'rt5645_i2c_probe':
>> sound/soc/codecs/rt5645.c:2720:4: error: implicit declaration of
>> function 'devm_gpiod_get_index'
>> [-Werror=implicit-function-declaration]
gpiod = devm_gpiod_get_index(&i2c->dev, "rt5645", 0);
^
>> sound/soc/codecs/rt5645.c:2720:10: warning: assignment makes pointer
>> from integer without a cast
gpiod = devm_gpiod_get_index(&i2c->dev, "rt5645", 0);
^
>> sound/soc/codecs/rt5645.c:2722:4: error: implicit declaration of
>> function 'gpiod_direction_input'
>> [-Werror=implicit-function-declaration]
if (IS_ERR(gpiod) || gpiod_direction_input(gpiod)) {
^
>> sound/soc/codecs/rt5645.c:2726:5: error: implicit declaration of
>> function 'desc_to_gpio' [-Werror=implicit-function-declaration]
rt5645->pdata.hp_det_gpio = desc_to_gpio(gpiod);
^
>> sound/soc/codecs/rt5645.c:2728:7: error: implicit declaration of
>> function 'gpiod_is_active_low'
>> [-Werror=implicit-function-declaration]
= !gpiod_is_active_low(gpiod);
^
cc1: some warnings being treated as errors
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
set platform specific data for intel strago platform
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All drivers have the same line at the end of the set_bias_level callback to
update the bias_level state. Move this update into
snd_soc_dapm_force_bias_level() and remove them from the drivers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the new snd_soc_codec_force_bias_level() helper function to invoke the
bias_level callback of a driver instead of calling the callback by hand.
Currently the effect of this is the same, but having all bias level updates
go through a central place will allow us to move more of the bias level
management into the DAPM core.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current code uses wrong mask when setting RT5645_DMIC_2_DP_GPIO12 bit,
fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the ACPI match ID for rt5645/5650 codec
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver will set RT5645_DEPOP_MAN bit in headphone power up
depop process. We need to restore it in headphone power down
process. Otherwise, we will get headphone noise when push button
function is enabled.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In codec bias level off, we need to disable gate mode with MCLK
for power saving. It is set by one bit. We don't need to write
while register for that.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5645 doesn't support auto incrementing writes so driver should set
the use_single_rw flag for regmap.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5650 and rt5645 use different register bits for format configuration.
This patch modifies rt5645_hw_params and rt5645_set_dai_fmt to support
both codecs.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove adc stereo2 filter since it is not in rt5645/rt5650 codec.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5650 and rt5645 use different register bits for TDM configuration.
This patch modifies rt5645_set_tdm_slot to support both codecs.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch defines an API to select the clock source for specified filters.
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Acked-by: Kevin Strasser <kevin.strasser@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
If no one defined the rt5645->pdata.hp_det_gpio in coreboot/bios.
It will cause kernel to reboot because rt5645->pdata.hp_det_gpio
is 0. So it is worth to add a check in rt5645_jack_detect.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Fang, Yang A <yang.a.fang@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are 3 JD modes in RT5645. This patch configure register
values according to platform data.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
