Use a single common table of struct earlycon_id for both command line
and devicetree. Re-define OF_EARLYCON_DECLARE() macro to instance a
unique earlycon declaration (the declaration is only guaranteed to be
unique within a compilation unit; separate compilation units must still
use unique earlycon names).
The semantics of OF_EARLYCON_DECLARE() is different; it declares an
earlycon which can matched either on the command line or by devicetree.
EARLYCON_DECLARE() is semantically unchanged; it declares an earlycon
which is matched by command line only. Remove redundant instances of
EARLYCON_DECLARE().
This enables all earlycons to properly initialize struct console
with the appropriate name and index, which improves diagnostics and
enables direct earlycon-to-console handoff.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UART controller is capable to perform transfers up to 4 Mbps.
Remove artificial 115.2 Kbps limitation.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add receive DMA support for UARTDM type of controllers.
Tested on APQ8064, which have UARTDM v1.3 and ADM DMA engine
and APQ8016, which have UARTDM v1.4 and BAM DMA engine.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add transmit DMA support for UARTDM type of controllers.
Tested on APQ8064, which have UARTDM v1.3 and ADM DMA engine
and APQ8016, which have UARTDM v1.4 and BAM DMA engine.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make function naming consistent across this driver.
Also rename msm_irq to msm_uart_irq. No functional changes.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bit masks for RFR_LEVEL1 and STALE_TIMEOUT_MSB values in MR1 and
IPR registers respectively are different for UART and UART_DM hardware
cores. We have been using UART core mask values for these. Add the same
for UART_DM core.
There is no bit setting as UART_IPR_RXSTALE_LAST for UART_DM core so do
it only for UART core.
Signed-off-by: Pramod Gurav <gpramod@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
unregister_console() will be called from uart_remove_one_port() while
removing the platform driver. So not necessary to call it in driver
exit path.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The change does following:
- baud, flow, bits, parity were being overwritten as they were
being reinitialized after parsing. Initialize them when they are
declared so that user provided setting are not overwritten.
- msm_set_baud_rate() is anyway called in uart_set_options when it calls
msm_set_termios(). msm_reset() is called when we change the baud rate.
Hence doing away with both of these calls.
- CR_CMD_PROTECTION_EN and CR_TX_ENABLE settings are done in msm_set_baud_rate.
So do away with this here.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes, just
removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There are
some ath9k patches coming in through this tree that have been acked by
the wireless maintainers as they relied on the debugfs changes.
Everything has been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlSOD20ACgkQMUfUDdst+ylLPACg2QrW1oHhdTMT9WI8jihlHVRM
53kAoLeteByQ3iVwWurwwseRPiWa8+MI
=OVRS
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
If there isn't a DT alias then of_alias_get_id() will return
-ENODEV. This will cause the msm_serial driver to fail probe,
when we want to keep the previous behavior where we generated a
dynamic line number at probe time. Restore this behavior by
generating a dynamic id if the line number is still negative
after checking for an alias or in the non-DT case looking at the
.id field of the platform device.
Reported-by: Kevin Hilman <khilman@kernel.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We rely on probe order of this driver to determine the line number for
the uart port. This makes it impossible to know the line number
when these devices are populated via DT. Use the DT alias
mechanism to assign the line based on the aliases node.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need to issue a reset if we ever change the value of the IPR
register on DM hardware. If we don't reset the hardware the RX
stale interrupt never triggers and the only way to trigger an RX
handling event is by filling up the fifo. This causes things like
getty to not work so well considering it might change the baud
rate a few times. Fix this by moving the reset on startup and any
reprogramming required after the reset to be after we change the
baud rate.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To properly support sysrq on uartDM hardware we need to properly
handle break characters. With the DM hardware the fifo can pack 4
characters at a time, where a break is indicated by an all zero
byte. Unfortunately, we can't differentiate between an all zero
byte for a break and an all zero byte of data, so try and do as
best we can. First unmask the RX break start interrupt and record
the interrupt when it arrives. Then while processing the fifo,
detect the break by searching for an all zero character as long
as we recently received an RX break start interrupt. This should
make sysrq work fairly well.
Cc: Frank Rowand <frank.rowand@sonymobile.com>
Cc: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for DT based and command line based early console on platforms
with the msm serial hardware.
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Frank reports that after continuing in kgdb the RX stale event
doesn't occur until after the RX fifo is filled up with exactly
the amount of characters programmed for the RX watermark (in this
case it's 48). To read a single character from the uartdm
hardware we force a stale event so that any characters in the RX
packing buffer are flushed into the RX fifo immediately instead
of waiting for a stale timeout or for the fifo to fill. Forcing
that stale event asserts the stale interrupt but we never clear
that interrupt via UART_CR_CMD_RESET_STALE_INT in the polling
functions. So when kgdb continues the stale interrupt is left
pending in the hardware and we don't timeout with a stale event,
like we usually would if a user typed one character on the
console, until the reset stale interrupt and stale event commands
are sent. Frank could get things working again by running
handle_rx_dm(). By putting enough characters into the fifo he
could trigger a watermark interrupt, and thus cause
handle_rx_dm() to run finally resetting the stale interrupt
and enabling the stale event so that single characters would
cause timeouts again.
The fix is to just do what the interrupt routine was doing all
along and clear the stale interrupt and enable the event again.
Doing this also smooths over any differences in the fifo behavior
between v1.3 and v1.4 hardware allowing us to skip forcing the
uart into single character mode.
Reviewed-by: Frank Rowand <frank.rowand@sonymobile.com>
Tested-by: Frank Rowand <frank.rowand@sonymobile.com>
Fixes: f7e54d7ad7 "msm_serial: Add support for poll_{get,put}_char()"
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fixed below checkpatch.pl warning:
WARNING: else is not generally useful after a break or return
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes below checkpatch.pl warning and it remove extra blank lines:
WARNING: Missing a blank line after declarations
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
fixed below checkpatch.pl warning:
WARNING: braces {} are not necessary for any arm of this statement
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Kiran Padwal <kiran.padwal@smartplayin.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To support big-endian CPUs use the string versions of the io
read/write macros on the TX/RX fifos and the non-raw variants of
the readl/writel macros throughout. This way we don't byteswap
the characters coming from the fifos but we properly deal with
the little-endian nature of the serial hardware while controlling
it.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a risk that the variable will be used without being initialized.
This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A new set of bug fixes for 3.16, containing patches for seven platforms:
at91:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
imx:
- Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
because controller base CD/WP is not working in esdhc driver due to
runtime PM support
- A couple of random ventana gw5xxx board fixes
- Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
IPUv3 driver out of staging tree
- Fix enet/fec clock selection on imx6sl
- Fix display node on imx53-m53evk board
- A couple of Cubox-i updates from Russell, which were omitted from
the merge window due to dependency
integrator:
- fix an OF-related regression against 3.15
mvebu:
- mvebu (v7)
- Fix broken SoC ID detection
- Select ARM_CPU_SUSPEND for v7
- Remove armada38x compatible string (no users yet)
- Enable Dove SoC in mvebu_v7_defconfig
- kirkwood
- Fix phy-connection-type on GuruPlug board
qcom:
- enable gsbi driver in defconfig
- fix section mismatch warning in serial driver
samsung:
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
sti:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=fJMs
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A new set of bug fixes for 3.16, containing patches for seven
platforms:
at91:
- drivers/misc fix for Kconfig PWM symbol
- correction of several values in DT after conversion to CCF
- fix at91sam9261/at91sam9261ek mistake in slow crystal vs. slow RC osc
imx:
- Use GPIO for card CD/WP on imx51-babbage and eukrea-mbimxsd51,
because controller base CD/WP is not working in esdhc driver due to
runtime PM support
- A couple of random ventana gw5xxx board fixes
- Add IMX_IPUV3_CORE back to defconfig, which gets lost when moving
IPUv3 driver out of staging tree
- Fix enet/fec clock selection on imx6sl
- Fix display node on imx53-m53evk board
- A couple of Cubox-i updates from Russell, which were omitted from
the merge window due to dependency
integrator:
- fix an OF-related regression against 3.15
mvebu:
- mvebu (v7)
- Fix broken SoC ID detection
- Select ARM_CPU_SUSPEND for v7
- Remove armada38x compatible string (no users yet)
- Enable Dove SoC in mvebu_v7_defconfig
- kirkwood
- Fix phy-connection-type on GuruPlug board
qcom:
- enable gsbi driver in defconfig
- fix section mismatch warning in serial driver
samsung:
- use WFI macro in platform_do_lowpower because exynos cpuhotplug
includes a hardcoded WFI instruction and it causes compile error
in Thumb-2 mode.
- fix GIC reg sizes for exynos4 SoCs
- remove reset timer counter value during boot and resume for mct
to fix a big jump in printk timestamps
- fix pm code to check cortex-A9 for another exynos SoCs
- don't rely on firmware's secondary_cpu_start for mcpm
sti:
- Ethernet clocks were wrongly defined for STiH415/416 platforms
- STiH416 B2020 revision E DTS file name contained uppercase, change to
lowercase"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
ARM: at91/dt: sam9261: remove slow RC osc
ARM: at91/dt: define sam9261ek slow crystal frequency
ARM: at91/dt: sam9261: correctly define mainck
ARM: at91/dt: sam9n12: correct PLLA ICPLL and OUT values
ARM: at91/dt: sam9x5: correct PLLA ICPLL and OUT values
misc: atmel_pwm: fix Kconfig symbols
ARM: integrator: fix OF-related regression
ARM: mvebu: Fix the improper use of the compatible string armada38x using a wildcard
ARM: dts: kirkwood: fix phy-connection-type for Guruplug
ARM: EXYNOS: Don't rely on firmware's secondary_cpu_start for mcpm
ARM: dts: imx51-eukrea-mbimxsd51-baseboard: unbreak esdhc.
ARM: dts: imx51-babbage: Fix esdhc setup
ARM: dts: mx5: Move the display out of soc {} node
ARM: dts: mx5: Fix IPU port node placement
ARM: mvebu: select ARM_CPU_SUSPEND for Marvell EBU v7 platforms
ARM: mvebu: Fix broken SoC ID detection
ARM: imx_v6_v7_defconfig: Enable CONFIG_IMX_IPUV3_CORE
ARM: multi_v7_defconfig: Add QCOM GSBI driver
ARM: stih41x: Rename stih416-b2020-revE.dts to stih416-b2020e.dts
tty: serial: msm: Fix section mismatch warning
...
If IGNBRK is set without either BRKINT or PARMRK set, some uart
drivers send a 0x00 byte for BREAK without the TTYBREAK flag to the
line discipline, when it should send either nothing or the TTYBREAK flag
set. This happens because the read_status_mask masks out the BI
condition, which uart_insert_char() then interprets as a normal 0x00 byte.
SUS v3 is clear regarding the meaning of IGNBRK; Section 11.2.2, General
Terminal Interface - Input Modes, states:
"If IGNBRK is set, a break condition detected on input shall be ignored;
that is, not put on the input queue and therefore not read by any
process."
Fix read_status_mask to include the BI bit if IGNBRK is set; the
lsr status retains the BI bit if a BREAK is recv'd, which is
subsequently ignored in uart_insert_char() when masked with the
ignore_status_mask.
Affected drivers:
8250 - all
serial_txx9
mfd
amba-pl010
amba-pl011
atmel_serial
bfin_uart
dz
ip22zilog
max310x
mxs-auart
netx-serial
pnx8xxx_uart
pxa
sb1250-duart
sccnxp
serial_ks8695
sirfsoc_uart
st-asc
vr41xx_siu
zs
sunzilog
fsl_lpuart
sunsab
ucc_uart
bcm63xx_uart
sunsu
efm32-uart
pmac_zilog
mpsc
msm_serial
m32r_sio
Unaffected drivers:
omap-serial
rp2
sa1100
imx
icom
Annotated for fixes:
altera_uart
mcf
Drivers without break detection:
21285
xilinx-uartps
altera_jtaguart
apbuart
arc-uart
clps711x
max3100
uartlite
msm_serial_hs
nwpserial
lantiq
vt8500_serial
Unknown:
samsung
mpc52xx_uart
bfin_sport_uart
cpm_uart/core
Fixes: Bugzilla #71651, '8250_core.c incorrectly handles IGNBRK flag'
Reported-by: Ivan <athlon_@mail.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
WARNING: drivers/tty/built-in.o(.data+0x3544): Section mismatch in
reference from the variable msm_platform_driver to the function
.init.text:msm_serial_probe()
The variable msm_platform_driver references
the function __init msm_serial_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch removes direct access of the GSBI registers. GSBI configuration
should be done through the GSBI driver directly.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Implement the polling functionality for the MSM serial driver.
This allows us to use KGDB on this hardware.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We recently added support to send more than one character at a
time for UARTDM hardware but we didn't add the same support in
the console code path. Add support here to speed up console
messages on UARTDM hardware.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all UARTDM hardware is part of a GSBI complex. Add support
for these devices and fix a bug where we assumed uartdm meant the
hardware was part of a GSBI complex.
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In downstream kernel we've standardized the clock consumer names
that MSM device drivers use. Replace the uart specific clock
names in this driver with the more standard 'core' and 'iface'
names. Also simplify the code by assuming that clk_prepare_enable
and clk_disable_unprepare() will properly check for NULL pointers
(it will because MSM uses the common clock framework).
Cc: David Brown <davidb@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current driver triggers a lockdep warning for if tty_flip_buffer_push() is
called with uart_port->lock locked. This never shows up on UP kernels and comes
up only on SMP kernels.
Crash looks like this (produced with samsung.c driver):
-----
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8)
[<c01b59ac>] (do_raw_spin_unlock+0xc4/0xd8) from [<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0)
[<c03627e4>] (_raw_spin_unlock_irqrestore+0xc/0x38) from [<c020a1a8>] (s3c24xx_serial_rx_chars+0)
[<c020a1a8>] (s3c24xx_serial_rx_chars+0x12c/0x260) from [<c020aae8>] (s3c64xx_serial_handle_irq+)
[<c020aae8>] (s3c64xx_serial_handle_irq+0x48/0x60) from [<c006aaa0>] (handle_irq_event_percpu+0x)
[<c006aaa0>] (handle_irq_event_percpu+0x50/0x194) from [<c006ac20>] (handle_irq_event+0x3c/0x5c)
[<c006ac20>] (handle_irq_event+0x3c/0x5c) from [<c006d864>] (handle_fasteoi_irq+0x80/0x13c)
[<c006d864>] (handle_fasteoi_irq+0x80/0x13c) from [<c006a4a4>] (generic_handle_irq+0x20/0x30)
[<c006a4a4>] (generic_handle_irq+0x20/0x30) from [<c000f454>] (handle_IRQ+0x38/0x94)
[<c000f454>] (handle_IRQ+0x38/0x94) from [<c0008538>] (gic_handle_irq+0x34/0x68)
[<c0008538>] (gic_handle_irq+0x34/0x68) from [<c00123c0>] (__irq_svc+0x40/0x70)
Exception stack(0xc04cdf70 to 0xc04cdfb8)
df60: 00000000 00000000 0000166e 00000000
df80: c04cc000 c050278f c050278f 00000001 c04d444c 410fc0f4 c03649b0 00000000
dfa0: 00000001 c04cdfb8 c000f758 c000f75c 60070013 ffffffff
[<c00123c0>] (__irq_svc+0x40/0x70) from [<c000f75c>] (arch_cpu_idle+0x28/0x30)
[<c000f75c>] (arch_cpu_idle+0x28/0x30) from [<c0054888>] (cpu_startup_entry+0x5c/0x148)
[<c0054888>] (cpu_startup_entry+0x5c/0x148) from [<c0497aa4>] (start_kernel+0x334/0x38c)
BUG: spinlock lockup suspected on CPU#0, kworker/0:1/360
lock: s3c24xx_serial_ports+0x1d8/0x370, .magic: dead4ead, .owner: <none>/-1, .owner_cpu: -1
CPU: 0 PID: 360 Comm: kworker/0:1 Not tainted 3.11.0-rc6-next-20130819-00003-g75485f1 #2
Workqueue: events flush_to_ldisc
[<c0014d58>] (unwind_backtrace+0x0/0xf8) from [<c0011908>] (show_stack+0x10/0x14)
[<c0011908>] (show_stack+0x10/0x14) from [<c035da34>] (dump_stack+0x6c/0xac)
[<c035da34>] (dump_stack+0x6c/0xac) from [<c01b581c>] (do_raw_spin_lock+0x100/0x17c)
[<c01b581c>] (do_raw_spin_lock+0x100/0x17c) from [<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28)
[<c03628a0>] (_raw_spin_lock_irqsave+0x20/0x28) from [<c0203224>] (uart_start+0x18/0x34)
[<c0203224>] (uart_start+0x18/0x34) from [<c01ef890>] (__receive_buf+0x4b4/0x738)
[<c01ef890>] (__receive_buf+0x4b4/0x738) from [<c01efb44>] (n_tty_receive_buf2+0x30/0x98)
[<c01efb44>] (n_tty_receive_buf2+0x30/0x98) from [<c01f2ba8>] (flush_to_ldisc+0xec/0x138)
[<c01f2ba8>] (flush_to_ldisc+0xec/0x138) from [<c0031af0>] (process_one_work+0xfc/0x348)
[<c0031af0>] (process_one_work+0xfc/0x348) from [<c0032138>] (worker_thread+0x138/0x37c)
[<c0032138>] (worker_thread+0x138/0x37c) from [<c0037a7c>] (kthread+0xa4/0xb0)
[<c0037a7c>] (kthread+0xa4/0xb0) from [<c000e5f8>] (ret_from_fork+0x14/0x3c)
-----
Release the port lock before calling tty_flip_buffer_push() and reacquire it
after the call.
Similar stuff was already done for few other drivers in the past, like:
commit 2389b27216
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Tue May 29 21:53:50 2007 +0100
[ARM] 4417/1: Serial: Fix AMBA drivers locking
Cc: David Brown <davidb@codeaurora.org> (maintainer:ARM/QUALCOMM MSM...)
Cc: Daniel Walker <dwalker@fifo99.com> (maintainer:ARM/QUALCOMM MSM...)
Cc: Bryan Huntsman <bryanh@codeaurora.org> (maintainer:ARM/QUALCOMM MSM...)
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following sparse warning:
drivers/tty/serial/msm_serial.c:237:37: error: incompatible types in comparison expression (different type sizes)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UARTDM cores have a TX fifo that can accept more than one
character per register write, but the msm_serial driver currently
only supports 1 character mode. Add support for this mode of operation
to speed up the transmit path on DM devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently msm_set_baud_rate() assumes the uart clock rate is
1.8432 MHz. This is not always true, and limits our options to
program the baud rate. Instead of assuming the rate and
hard-coding the baud_code based on it, calculate the divider that
we want and try to find the closest baud_code that matches. This
allows us to support uarts with faster clock speeds.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/msm_serial.c:302:6: warning: symbol 'msm_set_mctrl' was
not declared. Should it be static?
drivers/tty/serial/msm_serial.c:597:17: warning: incorrect type in argument 2
(different address spaces)
drivers/tty/serial/msm_serial.c:597:17: expected void volatile [noderef] <asn:2>*addr
drivers/tty/serial/msm_serial.c:597:17: got unsigned int *
drivers/tty/serial/msm_serial.c:608:33: warning: incorrect type in argument 1
(different address spaces)
drivers/tty/serial/msm_serial.c:608:33: expected void volatile [noderef] <asn:2>*addr
drivers/tty/serial/msm_serial.c:608:33: got unsigned int *gsbi_base
drivers/tty/serial/msm_serial.c:648:37: warning: incorrect type in assignment
(different address spaces)
drivers/tty/serial/msm_serial.c:648:37: expected unsigned int *gsbi_base
drivers/tty/serial/msm_serial.c:648:37: got void [noderef] <asn:2>*
Mark the ioremapped memory as __iomem and use writel instead of
iowrite because we're not dealing with PCI devices. Also, mark
msm_set_mctrl() static because it isn't used outside this file.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UARTDM serial devices require us to wait for the entire TX fifo
to drain before we can change the contents of the NCF_TX
register. Furthermore, if we write any characters to the TX fifo
within the same clock cycle of changing the NCF_TX register the
NCF_TX register won't latch properly.
To fix these issues we should read back the NCF_TX register to
delay any TX fifo accesses by a clock cycle and we should wait
for the TX fifo to drain (instead of just waiting for the fifo to
be ready to receive more characters). Failure to do so leads to
random NUL bytes interspersed in the output.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing iounmap() before return from msm_request_port()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clocks are not clk_put() in this driver's error paths during
probe. The code that checks for clock errors also fails to
properly return the error code from the pclk member if it turns
out to be the failing clock, leading to potentially confusing
error values if the clk member is not an error pointer. Fix these
problems with devm_clk_get() and proper error checking.
Removing the clk_put() in msm_serial_remove() also points out
that msm_port is unused. Furthermore, msm_port is the wrong type
and so the clk_put() would be using the wrong pointer. Replace it
with the proper type and call uart_remove_one_port() to do the
proper cleanup.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Add calls to clk_prepare and unprepare so that MSM can migrate to
the common clock framework.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David Brown <davidb@codeaurora.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_string this time.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver explicitly requests a clock rate for the UART, but it is
off by a factor of four from the dividers that it programs into the
UART. Fix this by setting the rate to 1/4 of the current value.
Signed-off-by: David Brown <davidb@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* 'next/dt' of git://git.linaro.org/people/arnd/arm-soc:
ARM: gic: use module.h instead of export.h
ARM: gic: fix irq_alloc_descs handling for sparse irq
ARM: gic: add OF based initialization
ARM: gic: add irq_domain support
irq: support domains with non-zero hwirq base
of/irq: introduce of_irq_init
ARM: at91: add at91sam9g20 and Calao USB A9G20 DT support
ARM: at91: dt: at91sam9g45 family and board device tree files
arm/mx5: add device tree support for imx51 babbage
arm/mx5: add device tree support for imx53 boards
ARM: msm: Add devicetree support for msm8660-surf
msm_serial: Add devicetree support
msm_serial: Use relative resources for iomem
Fix up conflicts in arch/arm/mach-at91/{at91sam9260.c,at91sam9g45.c}
Add devicetree support to the msm_serial driver. Clocks are still
queried by direct name from the driver until device tree clock support
is implemented.
Change-Id: Ia6b2ddfcf1e5dc3bd25dd502662f971202e6d56f
Signed-off-by: David Brown <davidb@codeaurora.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Device tree iomem resources are only accessible by index, and not by
name. The msm_serial devices always have either 1 or 2 iomem
resources, that are always in the same order. Convert the
platform_get_resource_byname into just platform_get_resource to
facilitate device tree conversion.
Change-Id: I4fd0f1037e07f2725a2a25c7b07dea2ca9397db7
Signed-off-by: David Brown <davidb@codeaurora.org>
