Remove a spurious blank line in the quota code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In case of system low latency configure passive scan to be fragmented.
Set the following scan parameters for both immediate and scheduled scan:
- passive scan fragment duration = 20ms
- out-of-channel time = 70ms
- suspend time = 105ms
Restructure channel's active/passive dwell time configuration to better
suit the above change.
The idea is that under low latency traffic passive scan is fragmented,
i.e. that dwell on a particular channel will be fragmented. Each
fragment dwell time is 20ms and fragments period is 105ms. Skipping to
next channel will be delayed by the same period (105ms). So suspend_time
parameter describing both fragments and channels skipping periods is set
to 105ms. This value is chosen so that overall passive scan duration
will not be too long. Max_out_time in this case is set to 70ms, so for
active scanning operating channel will be left for 70ms while for
passive still for 20ms (fragment dwell).
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Some scan parameters should be dependent on traffic conditions.
Centralize conditions verification in one function and obtain
scan max out-of-channel and suspend time in that new function.
Rely on bound interfaces indication instead of association state
to calculate scan parameters. If no bound interfaces use default
values for out-of-channel and suspend time parameters.
Additionally, get rid of NL80211_SCAN_FLAG_LOW_PRIORITY checks
since no use case for this exists so far.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
[reword commit log a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware decided to not implement this API in this way,
so for now remove setting the field completely. This will
allow the firmware to change how to use this field later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In order to debug the firmware, we need to be able to set
the BT priority of WiFi packets. This priority is set based
on the type of the packet (control frames, EAPOL etc...).
For debugging purposes, allow to override this priority by
a debugfs controlled value.
Enable this feature that needs this priority to be able to
test it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When the firmware asserts, the driver will dump the firmware
state to an internal buffer. This buffer is kept aside until
it is dumped through debugfs. Once an external application
fetched the data, the buffer is freed and a new buffer can
be allocated in case another assert occurs.
A udev event is sent to trigger an external application.
A simple rule like:
DRIVER=="iwlwifi", ACTION=="change", RUN+="/sbin/dump_sram.sh"
can fetch the data from debugfs.
Here is my dump_sram.sh:
phyname=$(basename ${DEVPATH})
date=$(date +%F_%H_%M)
filename=/var/log/iwl-sram-${phyname}-${date}.bin
cat /sys/kernel/debug/ieee80211/${phyname}/iwlwifi/iwlmvm/fw_error_dump > ${filename}
The current SRAM size is 80KB so, currently:
$ ls -lh iwl-sram-phy0-2014-03-16_13_14.bin
-rw-r--r-- 1 emmanuel emmanuel 81K Mar 16 13:15 iwl-sram-phy0-2014-03-16_13_14.bin
and after compression:
$ ls -lh iwl-sram-phy0-2014-03-16_13_14.bin.xz
-rw-r--r-- 1 emmanuel emmanuel 13K Mar 16 13:15 iwl-sram-phy0-2014-03-16_13_14.bin.xz
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The pairing process initiated through mgmt sets the conn->auth_type
value regardless of BR/EDR or LE pairing. This value will contain the
MITM flag if the local IO capability allows it. When sending the SMP
pairing request we should check the value and ensure that the MITM bit
gets correctly set in the bonding flags.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The SMP specification is written with the assumption that both key
information, plaintextData and encryptedData follow the same little
endian byte ordering as the rest of SMP.
Since the kernel crypto routines expect big endian data the code has had
to do various byte swapping tricks to make the behavior as expected,
however the swapping has been scattered all around the place.
This patch centralizes the byte order swapping into the smp_e function
by making its public interface match what the other SMP functions expect
as per specification. The benefit is vastly simplified calls to smp_e.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make it possible to (correctly) pass data declared as const as the
src parameter to the swap56 and swap128 functions declare this parameter
also as const.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch adds the Redpine Signals' 91x wireless driver.
Signed-off-by: Fariya Fatima <fariyaf@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When disconnecting some CID, corresponded Tx vring get released. During vring
release, all descriptors get freed. It is possible that Tx NAPI working on the same
vring simultaneously. If it happens, descriptor may be double freed.
To protect from the race above, make sure NAPI won't process the same vring.
Introduce 'enabled' flag in the struct vring_tx_data. Proceed with Tx NAPI only if
'enabled' flag set. Prior to Tx vring release, clear this flag and make sure NAPI
get synchronized.
NAPI enablement status protected by wil->mutex, add protection where it was
missing and check for it.
During reset, disconnect all peers first, then proceed with the Rx vring. It allows for
the disconnect flow to observe proper 'wil->status' and correctly notify cfg80211 about
connection status change
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
make sure reset flow executed in order
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use 'real' indication for hardware state.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
GRO is easy to enable when already using NAPI framework,
and it improves CPU utilisation. Enable it by default.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These methods can change device state, serialize with others
similar ones like up/down
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when STA receiving connect() when already connected,
it should return error
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
upon fw error interrupt - in STA mode, disconnect/cancel scan and
then reset FW/HW
added module param - no_fw_recovery which is false by default
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wil_reset() removes vring's
At the same time NAPI may be active performing Rx/Tx completion.
If this happens, Rx/Tx polling functions going to access already removed vrings
Make sure NAPI is idle and won't be started prior to vring removal.
For this, track NAPI enabled state
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When switching between STA and AP modes, memory allocated for Rx vring leaks
This is because start_ap() allocates Rx vring but stop_ap() do not free it.
Logically, Rx vring is not valid (HW can't use it anymore), so free it in reset()
Also, check double init for Rx vring and bail out with -EINVAL
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Convert 2 often printed messages to dynamic ones
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure hardware to perform full reset on "power good". This mean,
reset HW on system boot. This improves card stability.
By default this is off.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Put all registers in order for easier navigation;
fix naming to reflect hardware cluster
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware bug triggered by the MSI init while INTx asserted for some reason.
De-assert INTx prior to MSI set-up
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Useful to detect hardware problems
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When FW crashes, dmesg get polluted with the "FW not ready"
error message. Print it only once per FW lifecycle
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Support for new chip revision. Revision read from the
internal register, PCIE config's "revision id" register
do not indicate HW version properly
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce enum to describe mapping type; allow 'none' in addition to
'single' and 'page'; this is preparation for GSO
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When setting fragmented skb for Tx, assign skb to the last descriptor
and set number of fragments in the 1-st one
On Tx complete, HW sets "DU" bit in Tx descriptor only for the last
descriptor; so search for it using number of fragments field.
Middle descriptors may have "DU" bit not set by the hardware.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New firmware do support scan while connected. Enable it.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connection established, as reported by WMI_CONNECT_EVENTID,
4-way handshaking required for the secure connection is not done
yet. It is indicated by another WMI event. Wait for it and only then
allow data traffic. In case of non-secure connection, FW reports
"data port open" immediately after connection.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The registers for temperature compensation need to
be programmed only for active chains. Use the TX chainmask
to make sure that this is done properly for QCA953x.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Along with AR9340 and AR955x, this is also needed for
the QCA953x SoC.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Eeprom read operations are mixed in the probe function.
Make the code more readable and clean by extracting this code and
moving it in a dedicated function.
The variable eeprom_cck_table_adr, now useless, is here because
it will be needed for rtl8187se support, that I hope to add soon.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SLOT, SIFS, DIFS, EIFS, CW and ACK-timeout registers are set in an
RF-code callback and their values are fixed.
This patch moves this off the rf-code, and introduce two new functions
that calculate these values depending by slot time and CW values
requested by mac80211.
This seems to improve performances on my setup.
Currently the ack and slot time values could be stored in a local
variable, but this patch stores it in the driver "priv" structure
because it will be useful for rtl8187se support that will be added
(hopefully) soon.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Basic rates setting is done with hardcoded register write with
fixed settings.
This patch introduces a new function that makes it possible to
configure basic rates and it add a check for mac80211
BSS_CHANGED_BASIC_RATES flag in order to eventually invoke that
function when needed.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While changing board-type variable to enum, I have added enum
value for rtl8187se by mistake.
This will causes gcc warnings with unhandled switch/cases.
Remove it temporarily until I will push also rtl8187se changes.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The nl80211 iftype was converted to a mode value and stored in
brcmf_cfg80211_vif structure. The value was used only within
brcmfmac driver to decide execution of conditional code. Better
use wireless_dev::iftype for that as the wdev is contained in
the brcmf_cfg80211_vif structure.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the SDIO driver goes in low power state it must assure that
a clock request in ChipCLKCSR is set. Otherwise waking up the
device can fail. The register is read and if necessary the ALP
clock will be requested.
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connecting without specifying the channel it can take quite
some time to connect. This is because not all parameters for the
scan operation are set to optimized values. This patch changes
these parameters resulting in a much faster connect in certain
situations.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SDIO tx uses a sequence number which is common for data
and control. This requires that access to this sequence number
is protected. A mutex was used to achieve this, but it also
required the reordering of code for tx control.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Daniel (Deognyoun) Kim <dekim@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCM4354 is an a/b/g/n/ac 2x2 WiFi chip. This patch adds support for it through
SDIO interface.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xikL
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.15: First pull request
This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
