Commit Graph

433 Commits

Author SHA1 Message Date
Jacob Keller
8e2813f59e ixgbe: check for WoL support in single function
This patch consolidates the case logic for checking whether a device supports
WoL into a single place. Previously ethtool and probe used similar logic that
was copied and maintained separately. This patch encapsulates the core logic
into a function so that a user only has to update one place.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-27 02:31:26 -07:00
Matthew Vick
a27416bbca igb: Force flow control off during reset when forcing speed.
During igb_reset(), we initiate a hardware reset which will clear our
flow control settings. For auto-negotiation, we re-negotiate them when
linking up again, but we need to force them off properly for the forced
speed case.

Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-27 02:28:45 -07:00
Bruce Allan
bdc125f73f e1000e: 82579 potential system hang on stress when ME enabled
Previously, a workaround was added to address a hardware bug in the
PCIm2PCI arbiter where a write by the driver of the Transmit/Receive
Descriptor Tail register could happen concurrently with a write of any
MAC CSR register by the Manageability Engine (ME) which could cause the
Tail register to have an incorrect value.  The arbiter is supposed to
prevent the concurrent writes but there is a bug that can cause the Host
(driver) access to be acknowledged later than it should.
After further investigation, it was discovered that a driver write access
of any MAC CSR register after being idle for some time can be lost when
ME is accessing a MAC CSR register.  When this happens, no further target
access is claimed by the MAC which could hang the system.
The workaround to check bit 24 in the FWSM register (set only when ME is
accessing a MAC CSR register) and delay for a limited amount of time until
it is cleared is now done for all driver writes of MAC CSR registers on
82579 with ME enabled.  In the rare case when the driver is writing the
Tail register and ME is accessing any MAC CSR register for a duration
longer than the maximum delay, write the register and verify it has the
correct value before continuing, otherwise reset the device.

This patch also moves some pre-existing macros from the hardware-specific
header file to the more appropriate generic driver header file.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-27 02:25:13 -07:00
Bruce Allan
36ceeb43ce e1000e: 82579 packet drop workaround
In K1 mode (a MAC/PHY interconnect power mode), the 82579 device shuts down
the Phase Lock Loop (PLL) of the interconnect to save power.  When the PLL
starts working, the 82579 device may start to transfer the packet through
the interconnect before it is fully functional causing packet drops.  This
workaround disables shutting down the PLL in K1 mode for 1G link speed.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-27 02:21:13 -07:00
Matthew Vick
2cb7a9cc00 e1000e: Enable DMA Burst Mode on 82574 by default.
Performance testing has shown that enabling DMA burst on 82574
improves performance on small packets, so enable it by default.

Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-27 02:19:35 -07:00
Matthew Vick
1c1093a44f e1000e: Disable Far-End LoopBack following reset on 80003ES2LAN.
80003ES2LAN has an errata such that far-end loopback may be activated by
bit errors producing a reserved symbol. In order to disable far-end
loopback quickly enough, disable it immediately following a reset.

Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-27 02:17:38 -07:00
David S. Miller
f24001941c Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")

The former moved around the sysctl register/unregister calls, the
later simply removed them.

With help from Stephen Rothwell.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-23 23:15:17 -04:00
Alexander Duyck
b2db497eb2 ixgbe: Identify FCoE rings earlier to resolve memory corruption w/ FCoE
This patch makes it so that we identify FCoE rings earlier than
ixgbe_set_rx_buffer_len.  Instead we identify the Rx FCoE rings at
allocation time in ixgbe_alloc_q_vector.

The motivation behind this change is to avoid memory corruption when FCoE
is enabled.  Without this change we were initializing the rings at 0, and
2K on systems with 4K pages, then when we bumped the buffer size to 4K with
order 1 pages we were accessing offsets 2K and 6K instead of 0 and 4K.
This was resulting in memory corruptions.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-17 15:43:02 -07:00
Benjamin Poirier
34948a947d ixgbe: add missing rtnl_lock in PM resume path
Upon resume from standby, ixgbe may trigger the ASSERT_RTNL() in
netif_set_real_num_tx_queues(). The call stack is:
	netif_set_real_num_tx_queues
	ixgbe_set_num_queues
	ixgbe_init_interrupt_scheme
	ixgbe_resume

Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-17 15:40:34 -07:00
David S. Miller
56845d78ce Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/ethernet/atheros/atlx/atl1.c
	drivers/net/ethernet/atheros/atlx/atl1.h

Resolved a conflict between a DMA error bug fix and NAPI
support changes in the atl1 driver.

Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15 13:19:04 -04:00
Greg Rose
2b2027124f ixgbe: UTA table incorrectly programmed
The UTA table was being set to the functional equivalent of promiscuous
mode.  This was resulting in traffic from the virtual function being
flooded onto the wire and the PF device. This resulted in additional
overhead for VF traffic sent to the network and in the case of traffic
sent to the PF or another VF resulted in unwanted packets on the wire.

This was actually not the intended behavior. Now that we can program
the embedded switch correctly we can remove this snippit of code. Users
who want to support this should configure the FDB correctly using the
FDB ops.

Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15 13:06:05 -04:00
John Fastabend
9dcb373c55 ixgbe: allow RAR table to be updated in promisc mode
This allows RAR table updates while in promiscuous. With
SR-IOV enabled it is valuable to allow the RAR table to
be updated even when in promisc mode to configure forwarding

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15 13:06:05 -04:00
John Fastabend
0f4b0add85 ixgbe: enable FDB netdevice ops
Enable FDB ops on ixgbe when in SR-IOV mode.

Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15 13:06:04 -04:00
Don Skidmore
8f56e4b9ab ixgbe: add I2C clock stretching
This patch adds support for I2C clock stretching which is required per
SFF-8636.  Customers with passive DA cables implement clock stretching
would fail without this patch.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-14 02:10:50 -07:00
Carolyn Wyborny
be0c006814 igb: Update version to 3.4.7.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-14 02:07:13 -07:00
Bruce Allan
04499ec4ee e1000e: cleanup boolean logic
Replace occurrences of 'if (<bool expr> == <1|0>)' with
'if ([!]<bool expr>)'

Replace occurrences of '<bool var> = (<non-bool expr>) ? true : false'
with '<bool var> = <non-bool expr>'.

Replace occurrence of '<bool var> = <non-bool expr>' with
'<bool var> = !!<non-bool expr>'

While the latter replacement is not really necessary, it is done here for
consistency and clarity.  No functional changes.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-14 02:05:00 -07:00
Bruce Allan
6ad651456e e1000e: cleanup remaining strings split across multiple lines
Now that split strings generate checkpatch warnings (per Chapter 2 of
Documentation/CodingStyle to make it easier to grep the code for the
string) cleanup the remaining instances of them in the driver.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-14 02:04:02 -07:00
Richard Cochran
48425b1492 e100: enable transmit time stamping.
This patch enables software (and phy device) transmit time stamping.
Tested on an old PIII laptop with built in NIC.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-14 02:02:41 -07:00
Richard Cochran
abe0c5d165 e100: Support the get_ts_info ethtool method.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-14 02:01:33 -07:00
Don Skidmore
c509e754af ixgbe: fix WoL issue with fiber
There are times we turn of the laser before shutdown.  This is a bad thing
if we want to wake on lan to work so now we make sure the laser is on
before shutdown if we support WoL.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-14 01:47:11 -07:00
Bruce Allan
92fe173391 e1000e: issues in Sx on 82577/8/9
A workaround was previously put in the driver to reset the device when
transitioning to Sx in order to activate the changed settings of the PHY
OEM bits (Low Power Link Up, or LPLU, and GbE disable configuration) for
82577/8/9 devices.  After further review, it was found such a reset can
cause the 82579 to confuse which version of 82579 it actually is and broke
LPLU on all 82577/8/9 devices.  The workaround during an S0->Sx transition
on 82579 (instead of resetting the PHY) is to restart auto-negotiation
after the OEM bits are configured; the restart of auto-negotiation
activates the new OEM bits as does the reset.  With 82577/8, the reset is
changed to a generic reset which fixes the LPLU bits getting set wrong.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-14 01:45:54 -07:00
David S. Miller
06eb4eafbd Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net 2012-04-10 14:30:45 -04:00
Rob Herring
695e00789a net: remove ixp2000 ethernet driver
The platform is removed, so there are no users of this driver.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-04 18:09:37 -04:00
Richard Cochran
7ebae8177e igb: offer a PTP Hardware Clock instead of the timecompare method
This commit removes the legacy timecompare code from the igb driver and
offers a tunable PHC instead.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-04 00:48:13 -07:00
Richard Cochran
d339b13316 igb: add PTP Hardware Clock code
This patch adds a source file implementing a PHC. Only the basic
clock operations have been implemented, although the hardware
would offer some ancillary functions. The code is fairly self
contained and is not yet used in the main igb driver.

Every timestamp and clock read operation must consult the overflow
counter to form a correct time value. Access to the counter is
protected by a spin lock, and the counter is implemented using the
standard cyclecounter/timecounter code.

Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-04 00:34:23 -07:00
Emil Tantilov
7116130251 ixgbe: consolidate reporting of MSIX vectors into a single function
This patch modifies ixgbe_get_pcie_msix_count_generic() to support
all current HW and removes the 82598 specific function.

- change the type of ixgbe_get_pcie_msix_count_generic() to u16
- include a check to make sure the maximum allowed number of vectors
is not exceeded.

Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-04 00:27:19 -07:00
Bruce Allan
fad59b0d3f e1000e: update driver version number
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-04 00:25:52 -07:00
Bruce Allan
1e36052e44 e1000e: cleanup indexed register arrays
Some Rx and Tx specific registers are arrays indexed by the queue number.
For clarity, specify the intended queue rather than obscuring it behind a
define.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-04 00:24:42 -07:00
Bruce Allan
c58c8a784b e1000e: cleanup NAPI routine
Rename NAPI polling routine and a parameter with more appropriate names,
refactor a conditional branch to get rid of an unnecessary goto/label and
fix a line exceeding 80 columns.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-04 00:23:40 -07:00
Matthew Vick
397c020ac2 e1000e: Minor comment clean-up.
Move the first phrase of a multi-line comment to the second line.

Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-04 00:22:37 -07:00
Ben Greear
e825b73182 e1000: Support RX-ALL flag.
This allows the NIC to receive errored frames (bad FCS, etc)
and pass them up the stack.  This can be useful when using
sniffers.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-04 00:21:27 -07:00
Matthew Vick
bf03085f85 e1000e: Guarantee descriptor writeback flush success.
In rare circumstances, a descriptor writeback flush may not work if it
arrives on a specific clock cycle as a writeback request is going out.

Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-03 15:25:16 -07:00
Bruce Allan
bb9e44d0d0 e1000e: prevent oops when adapter is being closed and reset simultaneously
When the adapter is closed while it is simultaneously going through a
reset, it can cause a null-pointer dereference when the two different code
paths simultaneously cleanup up the Tx/Rx resources.

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-03 15:25:08 -07:00
Multanen, Eric W
aacc1bea19 ixgbe: driver fix for link flap
Fix up code so that changes in DCB settings
are detected only when ixgbe_dcbnl_set_all is called.
Previously, a series of 'change' commands followed by
a call to ixgbe_dcbnl_set_all() would always be handled
as a HW change - even if the net change was zero.
This patch checks for this case of no actual change and
skips going through the HW set process.

Without this fix, the link could reset and result in
a link flap.

The core change in this patch is to check for changes
in the ixgbe_copy_dcb_cfg() routine - and return
a bitmask of detected changes.  The other
places where changes were detected previously can be removed.

Signed-off-by: Eric Multanen <eric.w.multanen@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-04-03 15:24:57 -07:00
Don Skidmore
8e4f3250f4 ixgbe: update version number
Update the driver version number to better match version of out of tree
driver that has similar functionality.

Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-03-27 23:46:28 -07:00
Don Skidmore
70e5576cb0 ixgbe: fix typo in enumeration name
This was pointed out to me by Xiaojun Zhang on Source Forge.

CC: Xiaojun Zhang <zhangxiaojun@sourceforge.net>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-03-27 23:34:54 -07:00
stephen hemminger
b3f4d5990b intel: make wired ethernet driver message level consistent (rev2)
Dan Carpenter noticed that ixgbevf initial default was different than
the rest. But the problem is broader than that, only one Intel driver (ixgb)
was doing it almost right.

The convention for default debug level should be consistent among
Intel drivers and follow established convention.

Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-03-27 23:29:22 -07:00
Jiri Pirko
52f5509fe8 e1000: fix vlan processing regression
This patch fixes a regression introduced by commit "e1000: do vlan
cleanup (799d531)".

Apparently some e1000 chips (not mine) are sensitive about the order of
setting vlan filter and vlan stripping/inserting functionality. So this
patch changes the order so it's the same as before vlan cleanup.

Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-03-27 18:43:55 -07:00
Linus Torvalds
9f3938346a Merge branch 'kmap_atomic' of git://github.com/congwang/linux
Pull kmap_atomic cleanup from Cong Wang.

It's been in -next for a long time, and it gets rid of the (no longer
used) second argument to k[un]map_atomic().

Fix up a few trivial conflicts in various drivers, and do an "evil
merge" to catch some new uses that have come in since Cong's tree.

* 'kmap_atomic' of git://github.com/congwang/linux: (59 commits)
  feature-removal-schedule.txt: schedule the deprecated form of kmap_atomic() for removal
  highmem: kill all __kmap_atomic() [swarren@nvidia.com: highmem: Fix ARM build break due to __kmap_atomic rename]
  drbd: remove the second argument of k[un]map_atomic()
  zcache: remove the second argument of k[un]map_atomic()
  gma500: remove the second argument of k[un]map_atomic()
  dm: remove the second argument of k[un]map_atomic()
  tomoyo: remove the second argument of k[un]map_atomic()
  sunrpc: remove the second argument of k[un]map_atomic()
  rds: remove the second argument of k[un]map_atomic()
  net: remove the second argument of k[un]map_atomic()
  mm: remove the second argument of k[un]map_atomic()
  lib: remove the second argument of k[un]map_atomic()
  power: remove the second argument of k[un]map_atomic()
  kdb: remove the second argument of k[un]map_atomic()
  udf: remove the second argument of k[un]map_atomic()
  ubifs: remove the second argument of k[un]map_atomic()
  squashfs: remove the second argument of k[un]map_atomic()
  reiserfs: remove the second argument of k[un]map_atomic()
  ocfs2: remove the second argument of k[un]map_atomic()
  ntfs: remove the second argument of k[un]map_atomic()
  ...
2012-03-21 09:40:26 -07:00
Cong Wang
4679026d78 net: remove the second argument of k[un]map_atomic()
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
2012-03-20 21:48:19 +08:00
Alexander Duyck
8f4a0a3d9f ixgbe: Fix issues with SR-IOV loopback when flow control is disabled
This patch allows us to avoid a Tx hang when SR-IOV is enabled.  This hang
can be triggered by sending small packets at a rate that was triggering Rx
missed errors from the adapter while the internal Tx switch and at least
one VF are enabled.

This was all due to the fact that under heavy stress the Rx FIFO never
drained below the flow control high water mark.  This resulted in the Tx
FIFO being head of line blocked due to the fact that it relies on the flow
control high water mark to determine when it is acceptable for the Tx to
place a packet in the Rx FIFO.

The resolution for this is to set the FCRTH value to the RXPBSIZE - 32 so
that even if the ring is almost completely full we can still place Tx
packets on the Rx ring and drop incoming Rx traffic if we do not have
sufficient space available in the Rx FIFO.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-19 17:37:21 -04:00
David S. Miller
f24fd89ab5 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-next 2012-03-19 17:24:27 -04:00
Jeff Kirsher
8af3c33f4d ixgbe: fix namespace issues when FCoE/DCB is not enabled
Resolve namespace issues when FCoE or DCB is not enabled.
The issue is with certain configurations we end up with namespace
problems. A simple example:

ixgbe_main.c
 - defines func A()
 - uses func A()

ixgbe_fcoe.c
 - uses func A()

ixgbe.h
 - has prototype for func A()

For default (FCoE included) all is good.  But when it isn't the namespace
checker complains about how func A() could be static.

To resolve this, created a ixgbe_lib file to contain functions used
by DCB/FCoE and their helper functions so that they are always in
namespace whether or not DCB/FCoE is enabled.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
2012-03-19 13:59:11 -07:00
Joe Perches
449e39d9d7 igbvf: Use ETH_ALEN
Remove an unnecessary #define and use memcpy
instead of a loop to copy an ethernet address.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-19 16:53:08 -04:00
Alexander Duyck
567d2de291 ixgbe: Correct flag values set by ixgbe_fix_features
This patch replaces the variable name data with the variable name features
for ixgbe_fix_features and ixgbe_set_features.  This helps to make some
issues more obvious such as the fact that we were disabling Rx VLAN tag
stripping when we should have been forcing it to be enabled when DCB is
enabled.

In addition there was deprecated code present that was disabling the LRO
flag if we had the itr value set too low.  I have updated this logic so
that we will now allow the LRO flag to be set, but will not enable RSC
until the rx-usecs value is high enough to allow enough time for Rx packet
coalescing.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-03-19 13:43:34 -07:00
Alexander Duyck
ef6afc0cac ixgbe: Add support for enabling UDP RSS via the ethtool rx-flow-hash command
This patch adds support for enabling or disabling UDP RSS via the
ethtool -N rx-flow-hash command.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-03-19 02:03:15 -07:00
Alexander Duyck
581330ba7b ixgbe: Whitespace cleanups
This patch contains several fixes for formatting in regards to whitespace.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-03-19 02:02:21 -07:00
Alexander Duyck
6ca4350788 ixgbe: Two minor fixes for RSS and FDIR set queues functions
This change fixes two minor issues. The first was the fact that we were
setting the return value to false twice in the set_rss_queues function.
The second is the fact that we should have been using "min_t(int," instead
of "min((int)" in set_fdir_queues.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-03-19 02:01:28 -07:00
Alexander Duyck
35937c055a ixgbe: drop err_eeprom tag which is at same location as err_sw_init
The err_eeprom and err_sw_init tags both go to the same location.  So
instead of maintaining two tags this patch combines them so we only use
err_sw_init.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-03-19 02:00:32 -07:00
Alexander Duyck
eb01b9759e ixgbe: Move poll routine in order to improve readability
This change relocates the ixgbe_poll routine so it is right next to the
interrupt routine that schedules and calls it.

Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2012-03-19 01:58:58 -07:00